Search results for "washer water valve"

ERP 5304514775 Washer Drain Pump Replaces Part Number:5304514775,  5304509619, 5304505248, AP6329666, PS12365827.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 3949247 Washer Lid Switch Replaces 3949247V The XPARTCO 3949247 is an aftermarket replacement lid switch assembly for Whirlpool top-load washers, and also fits select Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid models, including stacked washer/dryer laundry center units. This switch mounts to the underside of the cabinet top panel and tells the washing machine the lid is closed, allowing the wash cycle to begin. Black plastic with wire leads, sold individually. Over time, the plastic on the switch's actuator can become brittle with age and break when the lid is closed roughly, or from the movement of an unbalanced load causing parts of the washer to strike it. Symptoms of a failing lid switch include the wash cycle not starting even when the lid is closed, error codes related to the lid being open, inability to advance through cycle selections, or the washer not spinning while still agitating normally. It directly replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098. Quick Answer The XPARTCO 3949247 Washer Lid Switch fixes Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid top-load washers (including laundry center combo units) that won't start with the lid closed, show lid-open error codes, won't advance through cycle selections, or agitate but won't spin. Black plastic, wire leads, sold individually. Replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098. Not the same as our 3949238 listing — these are separate, similarly-numbered switches used on different models. Common Problems This Part Fixes Wash cycle won't start even when the lid is closed Error codes related to the lid being open Inability to advance through cycle selections Washer agitates but won't spin Flashes or other improper lid switch behavior Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch is compatible with select Whirlpool top-load washers, and also fits select Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers built on the Whirlpool platform, including stacked washer/dryer laundry center units, and model numbers such as 11010202000, 11010202001, 11010502990, 11010502991, 11010852990, 11010852991, 11012202100, 11012502100, 11012852100, 11013202200, 11013212200, 11014102300, 11014112300, 11014202300, 11014212200, 11018202790, 11018522790, 11018522791, 11018532790, 11018542890, 11018542891, 11018609890, 11018702790, 11018702791, 11019101990, 11019101991, 11019101992, 11019202200, and 11020112000. Note — not the same as 3949238: Our 3949238 listing is a separate, similarly-numbered lid switch used on different models. Whirlpool also uses several other distinct lid switch designs, including the direct-drive style (8318084) and the thin-twin style (3355806), which are not interchangeable with this switch. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your washer needs. Key Features Aftermarket replacement lid switch assembly — confirms the lid is closed before allowing the wash cycle to begin Resolves "won't start," "lid-open error codes," "can't advance cycle selections," and "agitates but won't spin" symptoms Black plastic construction with wire leads Mounts to the underside of the cabinet top panel Direct drop-in replacement matching the original mounting and connection Replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098 Compatible with Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers, including laundry center units Aftermarket replacement built to OEM-equivalent quality standards Sold individually Product Specifications Part Number 3949247 OEM Part Number 3949247V Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Material plastic Wiring Wire leads Mounting Location Underside of cabinet top panel Function Confirms lid is closed before allowing the wash cycle to begin Repair Difficulty Easy — basic hand tools Quantity 1 lid switch (sold individually) Compatible Brands Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, KitchenAid Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Unplug your washer from the wall outlet and turn off the water supply before beginning. Wear work gloves. Remove the screws holding the access panel in place at the back of the machine, then carefully remove the panel and set it aside. Locate the lid switch assembly near the top, center of the washer's interior. Use a Phillips and flathead screwdriver to unscrew the three screws that hold the lid switch assembly in place. Disconnect the wire harness from the old lid switch and carefully remove it from the machine. Install the new 3949247 into the machine in the exact same manner the old switch was removed. Connect the wire harness to the new switch. Reattach the three screws to secure the switch in place. Replace the access panel and reattach its screws. Turn on the water supply and plug in the washer. Run a test cycle with the lid closed to confirm the washer starts and spins normally. Tools needed: Phillips head screwdriver, flat head screwdriver. Frequently Asked Questions My washer agitates but won't spin. Is this the part I need? Yes, this is a well-documented symptom of a failed lid switch. This switch tells the washer's control system that the lid is closed before allowing certain functions, and spin specifically often requires this signal — a failed switch commonly leaves agitation working while blocking spin. Why does this switch fail over time? The plastic on the switch's actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it during a cycle. Is this the same as the 3949238 switch? No, these are separate lid switch part numbers, despite the similar numbering. Our 3949238 listing is used on different models. Always confirm your exact part number from your washer's parts diagram or the sticker on your old switch before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the material, wiring, and switching function of the original 3949247V lid switch assembly used in compatible Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC64-00519D Washer Genuine OEM Door Lock Replaces Part Numbers:  DC64-00519D, 4545806, AP6027082, PS11762120. Description: This Washer Door Lock Switch is an essential component for maintaining the security and functionality of your Samsung washer. Designed to ensure that the washer door remains securely locked during operation, this genuine OEM part guarantees reliable performance and durability. By replacing a faulty or damaged door lock switch with this high-quality assembly, you can restore your washer's ability to operate safely and efficiently.   

Read more less

XPARTCO WH49X10042 Washer Agitator Coupler The XPARTCO WH49X10042 is an aftermarket replacement agitator coupling kit for GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. Also known as the agitator drive bell or drive block, this small but essential part connects the transmission drive shaft to the agitator base, transmitting the back-and-forth rotational motion that lets the agitator move clothes through the wash cycle. Made of pale yellow plastic with a matte finish, this coupler measures approximately 3-7/16"L x 3-7/16"W x 3-1/8"H, and includes 1 agitator drive bell plus 1 hold-down bolt. Common causes of failure include normal wear and tear over time, or overuse with heavy or unbalanced loads that place extra strain on the coupler's plastic teeth. Symptoms of a bad coupler include the agitator not moving at all, moving too slowly or weakly, loud banging or grinding noises during operation, or oil stains appearing on clothes. It directly replaces WH43X10032, WH02X10037, WH43X10009, AH1517844, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, EA1482517, EA1517844, EAP1517844, PD00001044, PS1482517, PS1517844, AP3964635, and AP3995059. Quick Answer The XPARTCO WH49X10042 Washer Agitator Coupler fixes GE, Hotpoint, RCA, Haier, Monogram, and Café top-load washers where the agitator won't move, moves too slowly, makes banging or grinding noise, or leaves oil stains on clothes. Pale yellow plastic, includes drive bell and bolt. Replaces WH43X10032, WH02X10037, WH43X10009, AH1517844, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, EA1482517, EA1517844, EAP1517844, PD00001044, PS1482517, PS1517844, AP3964635, AP3995059. Several customers describe this as an easy repair — a 7/16" socket removes the bolt, and the agitator hub then pulls off by hand. Common Problems This Part Fixes Agitator not moving at all during the wash cycle Agitator moving too slowly or weakly Loud banging or grinding noise during operation Oil stains appearing on clothes after washing Agitator feeling loose or slipping when pushed or pulled by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer agitator coupler directly replaces the following OEM and cross-reference part numbers: WH49X10042, WH43X10032, WH02X10037, WH43X10009, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, AH1517844, AGE26676, AP3964635, OEM11893914, EA1517844, EAP1517844, PD00001044, PS1517844 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This agitator coupler is compatible with select GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform. Fits newer top-load washer designs. Note: Always verify your full model number before ordering, since GE uses different agitator coupler designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement agitator coupling kit — also known as the agitator drive bell or drive block Connects the transmission drive shaft to the agitator base Resolves "agitator not moving," "moving too slowly," "banging or grinding noise," and "oil stains on clothes" symptoms Pale yellow plastic, matte finish Approximately 3-7/16"L x 3-7/16"W x 3-1/8"H Includes 1 agitator drive bell and 1 hold-down bolt Direct drop-in replacement matching the original mounting Replaces WH43X10032, WH02X10037, WH43X10009, AH1517844, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, EA1482517, EA1517844, EAP1517844, PD00001044, PS1482517, PS1517844, AP3964635, and AP3995059 Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café top-load washers Aftermarket replacement built to OEM-equivalent quality standards Simple, quick DIY repair with basic tools Product Specifications Part Number XPWH49X10042 OEM Part Number WH49X10042 Part Type Washer Agitator Coupling Kit (Drive Bell) Condition Aftermarket Replacement Color Pale Yellow Material Plastic Finish Matte Dimensions 3-7/16"L x 3-7/16"W x 3-1/8"H Includes 1 agitator drive bell, 1 hold-down bolt Repair Difficulty Easy — 7/16" socket required Quantity 1 agitator coupling kit Compatible Brands GE, Hotpoint, RCA, Haier Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Remove the fabric softener dispenser or cap from the top of the agitator if your model has one. Using a 7/16" socket, remove the hold-down bolt securing the agitator to the transmission drive shaft. Pull the agitator straight up and off the hub — this typically comes off easily by hand once the bolt is removed. Locate the old coupler (drive bell) on the drive shaft and remove it, noting its orientation. Install the new WH49X10042 coupler onto the drive shaft in the same orientation. Place the agitator back down onto the hub, aligning it correctly, and reinstall the hold-down bolt, tightening it securely with the 7/16" socket. Reattach the fabric softener dispenser or cap. Restore power and run a test cycle to confirm the agitator moves properly through its full back-and-forth range with no unusual noise. Tools needed: 7/16" socket and ratchet, work gloves. Frequently Asked Questions My agitator isn't moving at all. Is this the part I need? Yes, this is the most common symptom of a failed agitator coupler. Since this part is what transmits rotational motion from the transmission to the agitator, worn or stripped plastic teeth inside the coupler can prevent that motion from being transferred, leaving the agitator still or barely moving even though the motor and transmission are working fine. Is this a difficult repair? No, this is one of the simpler washer repairs. Multiple customers describe it as very easy: remove a single 7/16" bolt, pull the agitator off the hub by hand, swap the coupler, and reverse the process. No special skills are typically required. Why does my washer make banging or grinding noise? A worn agitator coupler can cause this noise as its plastic components degrade and no longer mesh smoothly with the transmission shaft. Replacing the coupler typically resolves this noise along with any accompanying agitation problems. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the size, material, and drive shaft fit of the original WH49X10042 agitator coupling kit used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11130359 Washer Suspension Rod Kit – Compatible with Whirlpool, Maytag, Amana, Crosley, and Roper Washers Product Description Reduce vibration and restore smooth, stable operation with the XPARTCO W11130359 Washer Suspension Rod Kit. This high-quality aftermarket replacement supports the washer tub and absorbs movement during wash and spin cycles. Worn or broken suspension rods can cause loud banging noises, excessive shaking, or unbalanced loads. Replacing them with this reliable XPARTCO kit ensures balanced performance and extends the life of your washer. Replaces Part Numbers W11130359, W11027215, 4813873, W10594082, W10785954, W10821704, W10901060, W11033536, W11226784, AP6261901, PD00042502, EAP12347544, PS12347544. Compatibility This replacement suspension rod kit fits select Whirlpool, Maytag, Amana, Crosley, and Roper top-load washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC565FW0, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to match OEM performance and stability 🌀 Reduces Vibration – Keeps washer tub balanced during spin cycles 💰 Cost-Effective Solution – High-quality kit at a lower cost than OEM parts 🛠️ Complete Kit – Includes four suspension rods, bushings, and suspension springs 🛡️ Fixes Common Issues – Solves excessive shaking, banging, or unbalanced load problems 📐 Product Specification Part Number: W11130359 Component Type: Washer Suspension Rod Kit Includes: 4 suspension rods with springs and mounting bushings Material: Heavy-duty steel with corrosion-resistant coating Mounting: Direct-fit installation under washer tub Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, socket wrench ⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock or injury. Steps: Disconnect power and remove the washer lid or top panel. Support the washer tub with a sturdy object or strap. Remove the old suspension rods from their mounting holes. Install the new XPARTCO W11130359 rods one by one, attaching springs and bushings. Reassemble panels, plug in the washer, and run a test cycle to confirm smooth operation. ⏱️ Time Required: 30–40 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Eliminate noise and vibration — Add to Cart Now for a stable, long-lasting repair!

Read more less

WH08X10049 Washer Genuine OEM Door Boot Seal Washer Front Door Boot Gasket Fits specific GE Front Load Washer models. Replaces Part Numbers: WH08X10049, 1796738, AH3417678, EA3417678, AP4588624, PS3417678. Description: This Gasket is an OEM part for specific GE washing machine models. This gasket forms a seal between the washer door and the drum, preventing water from leaking during the wash cycle. It is crucial for maintaining the efficiency and cleanliness of the washing process by ensuring a tight seal.  You should replace this gasket if it becomes damaged or worn out. Causes of a bad gasket include wear and tear from regular use, exposure to harsh detergents or cleaning chemicals, mold or mildew buildup, or physical damage such as cuts or tears. Keeping the gasket in good condition is essential for preventing leaks and ensuring optimal washer performance.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM WH08X37938 Washer Lid Switch Assembly The WH08X37938 is a genuine OEM lid switch (lid lock) assembly from GE for GE and Hotpoint top-load washers, also used on select Kenmore models. The assembly locks the lid while the washer is running and releases it when the cycle ends, and it tells the control board the lid is closed and it's safe to run. When it wears out, cracks, or fails electrically, the washer may refuse to start, stop in the middle of a cycle, show a lid or door lock error, or fail to lock the lid at all. This assembly replaces the original lock and switch as a unit, so you do not have to diagnose which internal contact has failed. As a genuine OEM part, not an aftermarket equivalent, it matches the original factory fit and specification. It mounts on the washer cabinet with an electrical connector and is a straightforward repair, usually done in under an hour. Quick Answer The Genuine OEM WH08X37938 Lid Switch Assembly fixes a GE or Hotpoint top-load washer that won't start, stops mid-cycle, won't lock the lid, or shows a lid or door lock error because the lid lock is worn or has failed. Complete replacement lock and switch assembly, genuine OEM. Classic symptom: you close the lid and nothing happens, or the washer starts then stops and signals a lid or lock fault. Common Problems This Part Fixes Washer won't start when the lid is closed Washer stops partway through the wash, rinse, or spin Lid will not lock, or stays locked after the cycle ends Lid or door lock error codes Loose, cracked, or visibly damaged lid lock Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid switch assembly replaces the following part numbers: WH08X37938, WH08X32697, WH02X24399, WH08X32657, WH01X26694, WH01X24112, WH01X24114, WH01X26114, WH01X27954, WH08X31577, WH08X31222, 290D1580P001, 290D1580P002, 290D1580P003, 290D1580P004, 290D3070P001, EG-380843 M, AGE26076, AP7225583, EAP17626546, OEM21676758, PD00087323, PS17626546 These are earlier GE numbers for the lid lock, as the part was updated over time. If your old lock or parts diagram shows any of them, match against this list. Compatibility This assembly is listed for select top-load washers from: GE and Hotpoint, including GTUN275EM0WW, GTUN275GM0WW, GTUP240EM0WW, and GTUP240EM2WW Kenmore, including 363.71542211, 363.71542310, and 363.71542410 Note: The model list above is only a sample, and lid locks differ between GE washer generations. Confirm fit by matching the number on your old lock or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This part is for top-load washers. Key Features Genuine OEM GE lid switch (lid lock) assembly, not an aftermarket equivalent Replaces the lock and switch as a unit, with no need to find the failed contact Restores starting, locking, and unlocking at the end of the cycle Cross-references to WH08X32697, WH08X31577, and other earlier GE numbers Fits select GE, Hotpoint, and Kenmore top-load washers Mounts on the cabinet with a plug-in electrical connector Product Specifications Part Number WH08X37938 OEM Part Number WH08X37938 Part Type Washer Lid Switch (Lid Lock) Assembly Condition Genuine OEM Application Select GE, Hotpoint & Kenmore Top-Load Washers Installation Notes ⚠️ Unplug Power and Shut Off Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Open the lid and, following your model's service guide, remove the top panel or cabinet section to reach the lid lock mounted on the cabinet. Note the position of the old assembly, disconnect its wiring connector, and remove the screws holding it in place. Fit the new assembly in the same position, secure it, and reconnect the connector. Reassemble the washer, restore power and water, and run a short cycle to confirm the lid locks, the washer starts, and the lid releases at the end. Frequently Asked Questions My washer won't start with the lid closed. Is this the part I need? A failed lid lock is a common cause. The control board won't start a cycle unless it sees the lid is closed and locked. Check that the lid closes fully and that nothing is blocking it. If it still won't start, the lid lock is a likely cause. Is a lid switch the same as a lid lock? On these washers, the lid switch and lock are combined in one assembly, which this part replaces. My old part is marked WH08X32697 or WH08X31577. Will this work? Those numbers are on the Replaces list. Compare the connector and mounting against your old part, or contact our support team with your model number and we'll confirm. Will this fit my front-load washer? No. This is for top-load washers. Is this an OEM part? Yes. This is a genuine OEM GE part, not an aftermarket equivalent, so it matches the original factory fit and specification. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO MDS47123602 Washer Door Boot Gasket – Compatible with LG Front-Load Washers Product Description Stop leaks and restore proper sealing with the XPARTCO MDS47123602 Washer Door Boot Gasket. This high-quality aftermarket replacement forms a watertight seal between the washer door and tub, preventing water from leaking during wash and spin cycles. A worn, torn, or mold-damaged gasket can lead to leaks, odors, or excessive vibration. Replacing it with this durable XPARTCO gasket provides long-lasting protection and reliable washer performance. Replaces Part Numbers MDS47123602, MDS64237201, MDS64237202, MDS47123612, EAP3535210, PD00028934, AH3535210, EA3535210, AP5218575, PS3535210. Compatibility This replacement door boot gasket fits select LG front-load washers. Example compatible models include (but are not limited to):LG WM2650HWA, WM3470HVA, WM3570HWA, WM8000HVA, and WM3997HWA. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM fit, thickness, and sealing performance 💧 Leak-Proof Design – Forms a tight seal to prevent water escaping from the washer door 🌿 Mold-Resistant Material – High-grade rubber reduces mildew and odor buildup 🛠️ Durable Construction – Built to withstand heat, detergent, and high-spin vibration 🛡️ Fixes Common Issues – Solves leaks, mold/mildew odor, door seal tears, or water pooling 📐 Product Specification Part Number: MDS47123602 Component Type: Washer Door Boot Gasket (Door Seal) Material: High-strength, mold-resistant rubber Color: Gray (standard for LG models) Mounting: Installed between front tub and door frame using clamps Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, spring clamp tool (recommended), pliers ⚠️ Safety First: Always unplug the washer before installation to prevent electrical shock. Steps: Remove the washer top and front panel for access. Release the outer retaining spring clamp and remove the old gasket edge. Detach the inner clamp from the tub and remove the old gasket completely. Align and install the new XPARTCO MDS47123602 gasket around the tub opening. Reinstall inner clamp, then secure the outer clamp around the door frame. Reassemble the washer and perform a quick rinse cycle to test for leaks. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop washer leaks the right way — Add to Cart Now for a durable, budget-friendly replacement!

Read more less

W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly The W11670519 is a genuine Whirlpool OEM lid lock latch assembly for Maytag top-load washers on the Cabrio-style MVW platform. Unlike a simple mechanical lid switch, this is a true electronic lid lock: a 3-wire connector feeds the assembly, which both senses whether the lid is closed and physically locks it shut once a cycle with spin is underway. The control won't allow the washer to spin — and on many cycles won't even let it start — until this assembly confirms the lid is closed and locked, which is why a failing latch produces such a wide range of symptoms: a washer that won't start, a lid that won't lock or won't release, cycles that stall or interrupt partway through, or a washer that fills and agitates but refuses to spin. Built from high-strength, wear-resistant ABS and PP plastic with a precision locking mechanism, this assembly is designed to prevent the lid from popping open mid-spin, which protects against water leakage and the safety hazard of an open lid on a spinning basket. Common failure modes include a locking mechanism that has worn out and can no longer engage or release reliably, a broken internal switch that stops signaling lid status to the control board, and simple wear from years of daily cycling. It directly replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992. As a genuine OEM part, the W11670519 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly fixes Maytag top-load washers on the Cabrio-style MVW platform where the washer won't start, the lid won't lock or won't release, the washer fills and agitates but won't spin, the cycle stalls or interrupts, or the lid clicks repeatedly without locking. 3-wire electronic lid lock, ABS/PP construction. Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, EAP17215992. This is a locking latch assembly, not a simple lid switch — it's a different design from the direct-drive and GE-platform lid switches elsewhere in our catalog. Common Problems This Part Fixes Washer won't start even though the lid is closed Lid won't lock, or locks but won't release when the cycle ends Washer fills and agitates normally but won't spin Persistent clicking sound from the lid area without the lid actually locking Cycle stalling or interrupting partway through Lid feels loose or doesn't seat and lock the way it used to Error code related to the lid lock displayed on the control panel Water leakage risk from a lid that isn't sealing and locking properly during spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid lock latch assembly directly replaces the following OEM and cross-reference part numbers: W11670519, W11368616, AP7214714, AWP46151, PD00085482, 4981394, PS17215992, EAP17215992 W11368616 was an earlier number for this same assembly. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock latch assembly is compatible with select Maytag top-load washers on the Cabrio-style MVW platform, including model numbers such as: MVW4505MW0, MVW4505MW1, MVW4505MW2 MVW5035MW1, MVW5035MW2 MVW5430MW1, MVW5430MW2, MVW5430PBK0, MVW5430PBK1 MVW5435PBK0, MVW5435PBK1, MVW5435PW0, MVW5435PW1 Note: This is an electronic locking latch assembly for the Maytag Cabrio-style MVW platform, and it is a different design from the simpler lid switches used on other Whirlpool platforms — including our 8318084 (direct-drive top-load), 3355806 (Whirlpool thin-twin), WH12X955 (GE combo/spacemaker), and WH01X29528 (GE front-load door lock) listings. None of those are interchangeable with this assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which lid lock or switch your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism and switch design Electronic lid lock — both senses lid position and physically locks the lid during spin cycles Resolves "won't start," "lid won't lock or release," "fills but won't spin," and "cycle interruptions" symptoms caused by latch failure 3-wire connector for a direct plug-and-play electrical connection Constructed from high-strength ABS and PP plastic for wear and aging resistance Precision-designed locking mechanism helps prevent accidental lid opening during spin Direct drop-in replacement — no modification required Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11670519 Part Type Washer Lid Lock Latch Assembly Condition Genuine OEM Brand Whirlpool / Maytag Application Maytag Cabrio-Style Top-Load Washers (MVW Platform) Electrical Connection 3-wire connector Material High-strength ABS and PP plastic Function Senses lid closure and physically locks the lid during spin Supersedes W11368616 Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag Installation Notes ⚠️ Unplug Washer Before Starting — If The Lid Is Locked Shut, Release It Manually First Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. If the old latch has failed in the locked position and you can't open the lid, insert a small flathead screwdriver into the latch opening where the lock mechanism engages through the lid, and gently slide the mechanism back to release it — then prop the lid open so it can't re-close and re-lock while you work. Remove the two screws holding the top section (control panel, lid, and wash basket opening) and slide the top of the unit forward and up to remove it, then prop it securely (a sturdy support between the cabinet frame and the top panel works well) rather than relying on your hands to hold it up. With the top propped open, remove the plastic cowl that the lid latch sits inside, which also retains the lock mechanism. Unclip the wiring harness from the retaining clips running around the inside of the lid and let the assembly hang free. Photograph the wiring connections before disconnecting the 3-wire connector from the old assembly. At the back of the lid, two metal spring clips retain the mechanism — squeeze these with your fingers or a set of pliers to release the old assembly, then pop the new W11670519 into place the same way. Reconnect the 3-wire connector, reclip the wiring harness into its retaining clips, and reinstall the plastic cowl. Lower the top panel back into position, reinstall its retaining screws, and confirm the lid closes, latches, and locks correctly through a full test cycle including spin. Tools needed: small flathead screwdriver, Phillips screwdriver, pliers, a sturdy prop for the top panel, work gloves. Frequently Asked Questions My washer fills and agitates but won't spin. Is this the lid lock? Yes, this is one of the most common symptoms of a failing lid lock latch on this platform. The control requires confirmation that the lid is closed and locked before it will allow the higher-speed, higher-torque spin cycle to run, even if it's willing to run the gentler fill and agitate steps without full confirmation. If your washer gets partway through a cycle and simply refuses to spin, this assembly is a strong suspect. The lid keeps clicking but never actually locks. What does that mean? A repeated clicking sound without the lid actually locking usually points to a worn or failing internal locking mechanism inside this assembly — it's attempting to engage but can't complete the lock reliably. This is a textbook symptom that this part has worn out and needs replacement. My washer's lid is locked shut and won't open. How do I even get it open to do this repair? With the washer unplugged, you can usually manually release the lock: insert a small flathead screwdriver into the latch opening where the mechanism engages through the lid, and gently slide it back to disengage the lock. Once the lid is open, prop it so it can't fall shut and re-lock while you continue the repair. Is this the same part as the lid switches used on other Whirlpool washers? No. This is an electronic locking latch assembly specific to the Maytag Cabrio-style MVW platform, and it works differently from the simpler mechanical lid switches used on other Whirlpool-family platforms, including the direct-drive top-load switch, the Whirlpool thin-twin switch, and various GE-platform switches we also carry. These parts are not interchangeable with each other — always match the assembly to your specific washer platform. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-wire electrical connection, locking mechanism, and ABS/PP construction as the lid lock latch assembly originally installed in your Maytag Cabrio-style washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11612327 Dishwasher Genuine Circulation Pump Circulation pump and motor assembly Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935. Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.

Read more less

Genuine OEM WPW10453947 Washer or Dryer Control Knob  The Genuine OEM WPW10453947 is a factory-original control knob used on both washers and dryers across the Whirlpool platform — the same knob design is shared between select top-load washer cycle-selector dials and dryer cycle/timer dials, depending on the model. It mounts onto the control shaft on the console and is what the user grips to select a wash or dry cycle. Over time these knobs commonly crack, the D-shaped shaft-grip inside wears out and starts spinning freely on the shaft, or the knob's pointer/indicator fades or breaks off. As the genuine Whirlpool part, it matches the factory shaft profile, detent feel, and indicator marking of the original equipment, so there's no fit or cosmetic mismatch. It directly replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Installs in under 5 minutes with no tools required — it's a simple push-on friction fit in most applications. Quick Answer The Genuine OEM WPW10453947 Washer or Dryer Control Knob fixes Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers with a cracked, spinning, or missing cycle-selector knob. This is the factory-original Whirlpool knob — not an aftermarket equivalent — and is used on both washer and dryer control panels depending on model. Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Classic symptom: knob spins freely on the shaft without turning the dial, or won't stay in the selected cycle position. Common Problems This Part Fixes Control knob spins freely on the shaft without engaging the dial underneath Knob is cracked, chipped, or has broken retaining tabs on the back Knob won't stay pointed at the selected cycle Indicator marking or pointer on the knob is faded, worn, or broken off Knob is missing entirely, making it difficult to select a cycle Knob feels loose or wobbly on the control shaft Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This control knob directly replaces the following OEM and cross-reference part numbers: W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control knob is compatible with select washer and dryer models from the following brands: Whirlpool washers and dryers (including WTW4616FW1, NTW4700YQ0, and related models) Amana washers and dryers (select models) Admiral washers and dryers (select models) Inglis washers and dryers (select models) Roper washers and dryers (select models) Kenmore washers and dryers (select Whirlpool-built models) Crosley washers and dryers (select models) Maytag washers and dryers (select Whirlpool-built models) Note: This same knob is used across hundreds of washer and dryer model numbers on both appliance types. Always verify fit using your appliance's exact model number before ordering, since visually similar knobs with a different shaft profile are used on other platforms. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM control knob — factory-original fit, feel, and appearance Used on both washer and dryer control panels across the Whirlpool platform Resolves "knob spins freely," "cracked knob," and "missing cycle indicator" symptoms Matches original detent feel and cycle-position indicator Push-on friction fit — no tools required for installation Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979 Compatible with Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers Genuine OEM part — factory-specified materials and markings Product Specifications Part Number WPW10453947 OEM Part Number WPW10453947 Part Type Washer / Dryer Control Knob Condition Genuine OEM Replacement Application Washer or Dryer Cycle-Selector Control Panel Mounting Push-on friction fit to control shaft Compatible Brands Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, Maytag Installation Notes ℹ️ No Tools Required — Unplug Appliance First Disconnect power to the washer or dryer before beginning. Note the current cycle position of the old knob before removing it, so you can align the new one the same way. Grip the old knob firmly and pull straight outward, away from the console, to release it from the friction fit on the shaft. If it's cracked and difficult to grip, work a flat-blade screwdriver gently behind the knob's edge to help pry it free, taking care not to damage the console. Line up the new WPW10453947 knob's D-shaped (or splined) center opening with the flat side of the control shaft, and press straight in until it seats fully against the console. Restore power and test that the knob turns smoothly through each cycle position and the indicator lines up correctly. Frequently Asked Questions Is this knob for a washer or a dryer? Both — this is a shared control knob design used on select Whirlpool-platform washers and dryers, depending on the model. The knob itself is identical; what it controls (wash cycle vs. dry cycle) depends on which appliance and console it's installed in. Confirm your appliance's model number before ordering to make sure this is the correct knob for your specific control panel. My knob spins freely and doesn't change the cycle — is this the fix? Yes, in most cases. This happens when the knob's internal shaft-grip (the D-shaped or splined opening that mates with the control shaft) wears out or cracks, so the knob spins independently of the shaft underneath it. Replacing the knob restores a snug grip on the shaft so turning it actually moves the selector. Do I need any tools to install this? No — it's a simple push-on friction fit. Pull the old knob straight off the shaft (a flat-blade screwdriver can help pry a stuck or cracked one loose) and press the new one on, matching the shaft's flat side to the knob's opening. No screws or fasteners are involved. Is this a genuine Whirlpool part or an aftermarket equivalent? This is the genuine, factory-original Whirlpool knob — not an aftermarket equivalent. It matches the original shaft profile, detent feel, and cycle-indicator markings, so there's no mismatch in fit or appearance versus the original equipment. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine Whirlpool OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less