Search results for "washer Drain Pumps"

XPARTCO DC66-00777A Washer Pulsator Cap – Compatible with Samsung Washers Product Description Keep your washer operating smoothly with the XPARTCO DC66-00777A Washer Pulsator Cap. This high-quality aftermarket replacement covers the central pulsator bolt, preventing water, detergent, and debris from entering the washer hub. A cracked or missing cap can lead to corrosion, noise, or imbalance during spin cycles. Replacing it with this durable XPARTCO cap restores a secure seal and helps maintain optimal washing performance. Replaces Part Numbers DC66-00777A, PD00025125, EAP8753312, AP5788799, 3282678, PS8753312. Compatibility This replacement pulsator cap fits select Samsung top-load washers. Example compatible models include (but are not limited to): Samsung WA400PJHDWR/AA, WA422PRHDWR/AA, and WA45H7000AW/A2. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and performance for Samsung washers 💧 Protective Seal – Keeps water and detergent away from the pulsator bolt area 💰 Cost-Effective Solution – Durable and affordable alternative to OEM caps 🛠️ Simple Installation – No tools required; snaps directly into place 🛡️ Fixes Common Issues – Replaces missing or damaged caps to prevent rust and noise 📐 Product Specification Part Number: DC66-00777A Component Type: Washer Pulsator (Washplate) Cap Material: High-strength molded plastic Color: Gray or silver finish (varies by batch) Mounting: Snap-fit installation on top of pulsator bolt Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: None ⚠️ Safety First: Always unplug the washer before performing any maintenance to avoid electrical shock. Steps: Open the washer lid and locate the center of the pulsator (washplate). Remove any remaining parts of the old or damaged cap. Align the new XPARTCO DC66-00777A cap with the pulsator hub opening. Press firmly until it clicks into place. Verify the cap is secure before running a wash cycle. ⏱️ Time Required: Less than 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your washer from wear and debris — Add to Cart Now for a quick, reliable fix!

Read more less

XPARTCO 349241T Dryer Drum Roller Set (2-Pack) The XPARTCO 349241T is an aftermarket replacement dryer rear drum support roller set compatible with a wide range of Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef. The drum support rollers are cylindrical rubber-and-metal wheels mounted on shafts at the rear of the dryer cabinet that cradle and support the outer edge of the drum as it rotates. Without the rollers, the drum would drag directly on the cabinet, causing rapid wear and generating the loud thumping or squealing noise that indicates failing rollers. This set includes 2 drum rollers, 4 tri-ring retaining clips, and 2 retaining washers — everything needed for a complete rear roller replacement. Each roller measures 3-1/4"L x 1"W x 3-1/4"H and is constructed from rubber over a metal bearing hub with a plastic axle support. Both rollers must always be replaced at the same time. The set directly replaces 349241, 349241TVP, 8170, 8205, 337089, 340352, 661562, 3389901, 3397588, 3397590, AP3098345, PS347627, and several additional cross-reference numbers. Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 349241T Dryer Drum Roller Set fixes Whirlpool-family 29" dryers that are squealing, thumping, rumbling, or where the drum is not turning smoothly. Set of 2 rollers with 4 tri-rings and 2 retaining washers. 3-1/4"L x 1"W x 3-1/4"H each. Replace both rollers at the same time. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef 29" dryers. Replaces 349241, 8170, 8205, 337089, 3389901, AP3098345, PS347627. Common Problems This Part Fixes Loud thumping, rumbling, or squealing noise during the drying cycle Grinding or scraping sound when the drum is turning Drum turning unevenly or wobbling during operation Drum not spinning — rollers so worn they can no longer support the drum Squealing or squeaking that gets worse over time as roller bearings degrade Marks or scuff lines on clothes — drum dragging against the dryer cabinet Excessive vibration during the drying cycle Replaces Part Numbers This drum roller set directly replaces the following OEM and cross-reference part numbers: 349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AWP39168, AH347627, EA347627, K34-895, PD00002257, EAP347627, AP3098345, PS347627.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum roller set is compatible with select 29-inch gas and electric dryers from the following brands: Whirlpool dryers (gas and electric — 29" models) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Note: The 349241T rollers are for 29-inch Whirlpool-family dryers. Newer Whirlpool Duet front-load dryers and larger-capacity models use different roller part numbers (such as WPW10314173 / 8536974). Always verify your model number before ordering. Key Features Set of 2 rear drum support rollers — supports and cradles the drum as it rotates for smooth, quiet operation Includes all hardware: 2 rollers, 4 tri-ring retaining clips, 2 retaining washers — everything needed for a complete installation Dimensions: 3-1/4"L x 1"W x 3-1/4"H per roller Rubber wheel over metal bearing hub with plastic axle support — designed to resist wear and heat under continuous drum load Both rollers must be replaced at the same time — replacing only one results in uneven drum support and accelerated wear on the new roller Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair Compatible with 11 major appliance brands on the Whirlpool 29-inch platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 349241T Part Type Dryer Rear Drum Support Roller Set Condition Aftermarket Replacement Application 29-inch Gas and Electric Dryers Quantity Set of 2 rollers (replace both at the same time) Roller Dimensions 3-1/4"L x 1"W x 3-1/4"H (per roller) Material Rubber wheel / Metal bearing hub / Plastic axle support Color Black / White Kit Includes 2 drum rollers, 4 tri-ring retaining clips, 2 retaining washers Often Replaced With 341241 Drum Belt, 691366 or 279640 Idler Pulley Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to access the drum. Release the drive belt from the idler pulley, lift the drum forward, and set it aside. The rear drum support rollers are mounted on shafts on the rear bulkhead — each roller is secured with a tri-ring clip and a retaining washer. Use needle-nose pliers to remove the old tri-ring clips, then slide the old rollers off the shafts. Install the new rollers, new retaining washers, and new tri-ring clips on the shafts. Reinstall the drum, re-route the belt around the motor and idler pulley, and reassemble the front and top panels. Restore power and run a test cycle to verify quiet, smooth drum operation. Tip: while the dryer is open, inspect and replace the drum belt (341241) and idler pulley (691366 or 279640) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife, needle-nose pliers. Frequently Asked Questions What do the drum support rollers do? The rear drum support rollers are cylindrical wheels mounted on fixed shafts at the back of the dryer cabinet. As the drum rotates, its rear outer rim rests on these rollers, which carry the drum's weight and allow it to spin smoothly and quietly. When the rubber wheels wear down or the bearing hubs corrode, the drum no longer rides smoothly on the rollers — causing thumping, rumbling, or squealing noises that get progressively worse. In severe cases, worn rollers allow the drum to sag and drag against the cabinet rear panel. Why must I replace both rollers at the same time? Both rear drum support rollers carry the same load and experience the same wear through every drying cycle. When one roller fails, the other has been under the same stress for the same number of cycles and is almost certainly near the end of its useful life. Replacing only the failed roller leaves one worn roller supporting the drum unevenly, which puts extra stress on the new roller and causes it to wear out much faster. Replace both rollers at the same time to ensure even drum support and get the full service life from the new parts. Should I also replace the belt and idler pulley at the same time? Yes — this is the ideal time. Since the dryer must be fully disassembled to access the rear drum rollers, replacing the drum belt (341241) and idler pulley (691366 or 279640) at the same time is strongly recommended. All three parts wear at similar rates, and a worn belt or idler pulley is often what caused the rollers to wear prematurely. Doing all three in one repair eliminates the most common drum drive failure points and saves you from repeating the teardown in the near future. The 4392065 maintenance kit includes all three parts together. What causes dryer drum rollers to wear out? Drum rollers wear naturally over time from the continuous load of supporting the rotating drum. The most common accelerating factors are operating the dryer with a worn or broken belt (which allows the drum to sag and puts extra weight on the rollers), running very large or heavy loads frequently, and allowing lint to accumulate around the roller shafts, which causes the bearings to run dry and wear faster. Regular dryer maintenance — including cleaning lint from around the drum and periodically checking the belt — helps extend roller life. Is this an OEM or aftermarket part? This is an aftermarket replacement set built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from rubber, metal, and plastic to match the dimensions and load-bearing performance of the original 349241T drum roller set. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO MDS47123602 Washer Door Boot Gasket – Compatible with LG Front-Load Washers Product Description Stop leaks and restore proper sealing with the XPARTCO MDS47123602 Washer Door Boot Gasket. This high-quality aftermarket replacement forms a watertight seal between the washer door and tub, preventing water from leaking during wash and spin cycles. A worn, torn, or mold-damaged gasket can lead to leaks, odors, or excessive vibration. Replacing it with this durable XPARTCO gasket provides long-lasting protection and reliable washer performance. Replaces Part Numbers MDS47123602, MDS64237201, MDS64237202, MDS47123612, EAP3535210, PD00028934, AH3535210, EA3535210, AP5218575, PS3535210. Compatibility This replacement door boot gasket fits select LG front-load washers. Example compatible models include (but are not limited to):LG WM2650HWA, WM3470HVA, WM3570HWA, WM8000HVA, and WM3997HWA. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM fit, thickness, and sealing performance 💧 Leak-Proof Design – Forms a tight seal to prevent water escaping from the washer door 🌿 Mold-Resistant Material – High-grade rubber reduces mildew and odor buildup 🛠️ Durable Construction – Built to withstand heat, detergent, and high-spin vibration 🛡️ Fixes Common Issues – Solves leaks, mold/mildew odor, door seal tears, or water pooling 📐 Product Specification Part Number: MDS47123602 Component Type: Washer Door Boot Gasket (Door Seal) Material: High-strength, mold-resistant rubber Color: Gray (standard for LG models) Mounting: Installed between front tub and door frame using clamps Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, spring clamp tool (recommended), pliers ⚠️ Safety First: Always unplug the washer before installation to prevent electrical shock. Steps: Remove the washer top and front panel for access. Release the outer retaining spring clamp and remove the old gasket edge. Detach the inner clamp from the tub and remove the old gasket completely. Align and install the new XPARTCO MDS47123602 gasket around the tub opening. Reinstall inner clamp, then secure the outer clamp around the door frame. Reassemble the washer and perform a quick rinse cycle to test for leaks. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop washer leaks the right way — Add to Cart Now for a durable, budget-friendly replacement!

Read more less

W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve The W10844024 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers. This valve regulates the flow of water into the appliance during each fill stage of the wash cycle, opening and closing to admit the correct amount of water at the right times. Weighing approximately 0.2 lbs, common failure causes include mineral or sediment buildup inside the valve and general electrical wear in the solenoid. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, or a valve that's unusually noisy — starting and stopping repeatedly — during heavy wash cycles as it struggles to regulate flow correctly. It directly replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 Quick Answer The W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers that aren't filling with water, or that are unusually noisy — starting and stopping — during heavy wash cycles. Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996. Some households need a separate hose adapter for this valve if the existing water line connector has a smaller diameter than the new valve's fitting — check before you start, or be prepared for a quick hardware store trip. Common Problems This Part Fixes Dishwasher not filling with water at all Valve unusually noisy — starting and stopping repeatedly during heavy wash cycles Cycle stalling at the fill step and never advancing to wash Poor washing results due to insufficient water fill Leaking near the valve connections Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W10844024, 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers built on the Whirlpool platform, including model numbers such as KUDR25SHWH1, MDB4629AWB1, DU900PWKB0, DU900PWKQ0, and Kenmore 665.15522000, 66517662991, and 66516669991. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher during each fill stage of the cycle Resolves "won't fill" and "noisy, starts and stops when filling" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 Compatible with Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W10844024 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Weight Approx. 0.2 lbs Function Regulates water flow into the dishwasher during fill Repair Difficulty Easy to Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, Amana Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Check Your Hose Connector Size First Disconnect power at the outlet or shut off the circuit breaker, and disconnect the water lines connected to the old valve before beginning. Wear work gloves. Have a shop vacuum on hand — some customers have needed to remove standing water from the bottom of the dishwasher before starting this repair. Locate the old valve and use pliers to unscrew any screws or bolts connecting it to the appliance. Clean the area where the old valve was located, removing any debris before installing the new one. Check the diameter of your existing water line connector before starting — some households have a smaller-diameter connector than this new valve's fitting requires, in which case you'll need a separate hose adapter from a hardware store to complete the connection. Take the new W10844024 and place it in the same position as the old valve, making sure it's connected correctly, and secure any screws or bolts. Reattach the water lines to the new valve and reconnect power. Double-check all connections before restoring power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: pliers, possibly a hose adapter, shop vacuum (if needed), work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Will I need any extra parts for this installation? Possibly. A few customers have found their existing water line connector had a smaller diameter than this valve's fitting, requiring a separate hose adapter purchased locally from a hardware store to complete the connection. It's worth checking your connector size beforehand, or having a quick trip to the hardware store planned just in case. My dishwasher makes a noisy, start-and-stop sound when filling. Is that this valve? Yes, this is a documented symptom. One customer described their valve as "very noisy on heavy wash cycles, started and stopped when filling" before replacing it with this exact part, which resolved the issue. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688994 Washer Water Inlet Valve (Hot) The XPARTCO W11688994 is an aftermarket replacement hot water inlet valve compatible with select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The hot water inlet valve is mounted at the back of the washer where the hot water supply hose connects. When the washer's control board calls for hot water during a wash cycle, the valve's internal solenoid opens, letting hot water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with hot water at all, fill very slowly with hot water, fail to deliver hot or warm wash temperatures (even when selected), continuously drip water into the tub even when off, or display fill-related error codes. Construction is red and white plastic with a metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688994, W11036928, W11316255, W11486360, and AP7218602. Often replaced as a pair with the cold water inlet valve (W11688995, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688994 Washer Water Inlet Valve (Hot) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers that aren't filling with hot water, fill slowly with hot water, can't reach hot or warm wash temperatures, or have continuous water dripping into the tub when off. Red/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036928, W11316255, W11486360, AP7218602. Often paired with the cold water valve (W11688995, sold separately). Common Problems This Part Fixes Washer not filling with hot water — valve solenoid not opening when commanded Washer filling slowly with hot water — valve partially clogged or weak solenoid No hot or warm water in selected wash temperatures — only cold water flowing in Hot wash cycle running cool — hot valve not delivering normal flow Water continuously dripping into the tub when the washer is off — hot valve stuck open or not fully closing Water leaks at the hot valve body — internal seal failure Wash cycles taking much longer than normal due to slow hot fill Fill-related error codes when hot fill is required by the selected cycle Replaces Part Numbers This hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688994, W11316255, W11036928, W11486360, 4983330, AP7218602, AWP46795, EAP17216729, FIX17216729, OEM21655815, PD00085626, PS17216729.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — 7MWFC9822HC1, 8TWFC6810LW0, WFC682CLW0, WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0-HC3, MHW5630HW0-HW3, MHW6630HC0-HC3, MHW6630HW0-HW3, MHW8630HC0-HC4, MHW8630HW0-HW4 series Amana front-load washers — NFW5800HW0, NFW5800HW1, NFW5800HW2, NFW5800HW3, NFW5800HW4 and related models Inglis front-load washers — IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the hot water inlet valve (typically red). The matching cold water inlet valve is part number W11688995 (typically blue). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of hot water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for hot water and closes the moment the call is dropped 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Red and white plastic body with metal solenoid coil — heat-resistant construction designed for hot water cycle pressure and temperature Replaces W11036928, W11316255, W11486360, AP7218602, and PD00085626 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the cold water inlet valve (W11688995, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688994 Part Type Washer Water Inlet Valve (Hot) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Hot (paired cold valve is W11688995) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Red / White Material Plastic / Metal (heat-resistant) Often Paired With Cold Water Inlet Valve (W11688995, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Important: if the washer has just been running a hot cycle, allow the hot supply hose and valve to cool before handling — hot water can scald. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the hot valve is typically red. Disconnect the hot water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688994 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the hot supply hose at the wall, restore water and power, and run a test cycle on a hot or warm setting to confirm normal hot water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the cold water valve (W11688995) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions My washer isn't filling with hot water — is the hot valve the problem? Likely, yes — that's the most common symptom of a failed hot water inlet valve. Before replacing, do a few quick checks: 1) confirm the hot water supply at the wall is turned on and your home actually has hot water at that connection (test the faucet nearby); 2) check the supply hose for kinks or pinches; 3) inspect the inlet screen on the back of the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean, but the washer still won't get hot water, the W11688994 valve solenoid has likely failed and replacing it will resolve the issue. My washer fills but my hot wash isn't actually hot — could it still be this valve? Yes — when the hot inlet valve is partially failed (opening but not fully, or opening only briefly), the washer may complete its fill cycle by drawing extra cold water to compensate, but the resulting mix is much cooler than the selected wash temperature should be. If you've confirmed your home's hot water is hot, the supply hose is good, and you're still ending up with lukewarm "hot" washes, the hot valve is a likely cause. Replacing it restores proper hot water delivery and accurate wash temperatures. Should I replace the cold water valve at the same time? Yes, it's strongly recommended. The hot and cold inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching cold water valve is part number W11688995 (blue, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — could the hot valve be the cause? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the cold water supply at the wall and check if dripping continues. If it stops, the cold valve is at fault; if it continues, this hot valve is the cause. Replacing the W11688994 will resolve a leaking hot valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688994 hot water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers Product Description Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts. Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083. Compatibility: Compatible with models including but not limited to: Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS Other brands: Select models requiring DC96-01703G Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G. 🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA). Product Specification Part Number: XPDC96-01703G Component Type: Washer water level pressure switch Material: Durable plastic housing with metal contacts Terminal Type: Electrical connector. Operating Conditions: Suitable for high-humidity washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

471823492CM Blue Tip Diaphragm for Wascomat Water Valve Diaphragm with guide. Fits Wascomat water valves. Also replaces 823492.    This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10780048 Washer Suspension Rods Kit Washer Suspension Rods Kit, set of 4. Fits specific Kenmore, Maytag, Whirlpool top load machine models. Replaces Part numbers: W10780048, W10349191, 4185114, W10257087, W10257088, W10349193, W10748952, W10821948, AP5971398, PS11703290. Description: This Suspension Rods are replacement parts for specific Kenmore, Maytag, Whirlpool washing machine models. They are designed to support the washer's tub assembly, maintaining balance and stability during the spin and agitation cycles. These rods connect the tub to the washer's frame and help absorb vibrations, preventing excessive movement that can lead to operational issues.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

WD19X25278 Dishwasher Diverter Assembly The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning. The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK. Quick Answer The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first. Common Problems This Part Fixes Water pooling or leaking underneath the dishwasher Poor washing performance from one or both spray arms Unusual noise during the wash cycle Water not properly directed to the correct spray arm Inconsistent cleaning results between the upper and lower racks Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers: WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB. Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement diverter assembly — controls water flow to the spray arms Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms Valve and float assembly engineered to optimize water flow while minimizing noise Direct drop-in replacement matching the original mounting and connections Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair Product Specifications Part Number WD19X25278 OEM Part Number WD19X25278 Part Type Dishwasher Diverter Valve Assembly Condition Aftermarket Replacement Function Controls water flow direction to the upper and lower spray arms Design Valve and float assembly Repair Difficulty Easy to Moderate — DIY-friendly Quantity 1 diverter assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions I'm seeing water pooling under my dishwasher. Is this the part I need? Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it. Any tips to avoid damaging the new part during installation? Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this. Is this a difficult repair? No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X24378 Washer / Dryer Cycle Selector Knob The XPARTCO WH01X24378 is an aftermarket replacement cycle selector knob (options knob) compatible with a wide range of GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. The selector knob is one of the primary user controls on the appliance's control panel — it's what you grip and turn to choose the wash or dry options and settings for each load. On many GE-platform washers and dryers, this smaller selector knob works alongside a larger main timer/cycle knob to give you fine-grained control over the specific options within your selected cycle. Over time, selector knobs wear out from repeated twisting motions, get cracked or dropped, or lose their grip on the internal shaft — all of which make it difficult or impossible to change the appliance's settings. Constructed from heat-resistant plastic with a clean white and chrome finish. Snap-on installation — no tools required. Pulls straight off the control shaft and pushes back on. This knob directly replaces WH01X24378, AP5986397, 4396548, and PS11726904. Important: this is the smaller cycle selector/options knob. If you need the larger main timer knob for your GE washer, that's a different part number (PS11736611) — check which knob is broken before ordering. Installs in under 1 minute — no tools required. Quick Answer The XPARTCO WH01X24378 Washer Cycle Selector Knob replaces a cracked, loose, stripped, or missing selector knob on GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Heat-resistant plastic, white and chrome finish. Snap-on installation — pulls straight off, pushes back on. Replaces AP5986397, 4396548, PS11726904. This is the smaller cycle/options knob — NOT the larger main timer knob (PS11736611). No tools required. Common Problems This Part Fixes Selector knob cracked, broken, or split from age and repeated use Knob loose and slipping on the control shaft — no longer changes settings when turned Knob has stripped or damaged internal grip and won't stay coupled to the shaft Knob missing entirely from the control panel Knob damaged from impact — dropped or bumped Knob discolored, faded, or worn from years of daily handling Difficulty selecting cycle options — knob no longer clicks into detent positions cleanly Water or detergent damage to the knob material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycle selector knob directly replaces the following OEM and cross-reference part numbers: WH01X24378, 4396548, AGE26094, AP5986397, EAP11726904, OEM17959200, PD00037085, PS11726904. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This selector knob is compatible with select washers and dryers from the following brands: GE washers — GTW500ASNWS and related top-load models GE dryers — GTX42GASJWW, GTD45GASJ2WS and related models GE Profile and GE Café washers and dryers (select models) GE Monogram washers and dryers (select models) Hotpoint washers and dryers (select models) RCA washers and dryers (select GE-built models) Haier washers and dryers (select models using GE-platform controls) Important — Two Knobs, Two Part Numbers: Many GE washers and dryers have TWO knobs on the control panel: a larger main timer/cycle knob and a smaller cycle selector/options knob. The WH01X24378 is the smaller cycle selector/options knob. If your broken knob is the larger main timer knob, you need a different part number (PS11736611 on many GE models). Before ordering, visually confirm which knob is broken and compare the size and shape to the images. Contact our support team with your model number if you're unsure. Key Features Cycle selector/options knob — used to choose specific settings within your selected wash or dry cycle Snap-on installation — pulls straight off the control shaft, pushes straight back on; no tools or hardware required Heat-resistant plastic construction — designed for years of daily use without warping or cracking Clean white and chrome finish complements GE appliance styling Ergonomic shape for comfortable grip and precise cycle selection Restores full cycle control when the original knob has cracked, stripped, or gone missing Replaces WH01X24378, AP5986397, 4396548, and PS11726904 Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers Important: this is the smaller cycle selector/options knob — NOT the larger main timer knob (PS11736611, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick replacement — installs in under 1 minute Product Specifications Part Number XPWH01X24378 Part Type Washer/Dryer Cycle Selector Knob (Options Knob) Condition Aftermarket Replacement Application Washers and Dryers (GE platform) Knob Size Smaller cycle/options knob (NOT the larger main timer knob) Color White / Chrome Material Heat-resistant plastic Installation Snap-on — no tools required Larger Timer Knob Different part — PS11736611 (sold separately) Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer/Dryer Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Wear work gloves if desired. Locate the old cycle selector knob on the control panel of your washer or dryer. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools or hardware required). If the knob is stuck or the internal grip has stripped and it's spinning without releasing, use a soft cloth wrapped around it for better grip, or gently pry it off with a plastic tool (avoid metal tools that could damage the control panel finish). Once the old knob is off, inspect the metal or plastic control shaft — if it's damaged, worn round, or spinning freely with no resistance, the underlying switch or shaft may also need replacement. If the shaft is intact, align the new WH01X24378 knob with the flat sides of the shaft (the knob has a matching D-shape or flat receiver inside) and push it firmly into place until it seats fully. Rotate the knob through its full range of positions to confirm it clicks into detents cleanly and turns smoothly. Restore power and run a test cycle. Tools needed: None (soft cloth optional). Frequently Asked Questions Is this the smaller or larger knob on my GE washer? The WH01X24378 is the smaller cycle selector (options) knob. Many GE washers and dryers have two knobs on the control panel: a larger main timer/cycle knob that selects the primary wash program, and a smaller cycle options knob (this one) that selects sub-options like temperature, spin speed, or soil level. Before ordering, look at your control panel and identify which knob has failed — if the smaller knob is broken, this is the correct part. If the larger main timer knob is broken, you need a different part (PS11736611 on many GE models). The two knobs are not interchangeable. How do I remove the old knob if it's cracked or spinning without coming off? If the internal grip on the old knob has stripped and it's spinning freely on the shaft without releasing, wrap a soft cloth around it for extra grip and pull firmly straight up. If that still doesn't work, gently pry it off with a plastic pry tool (a plastic putty knife or credit card can work). Avoid metal tools that could scratch the control panel finish. If the knob is cracked, you can sometimes break away the broken pieces to expose the internal grip on the shaft, then work each piece off. Once the old knob is off, inspect the control shaft — if it's damaged or spinning without resistance, the underlying switch may need replacement too. Do I really not need any tools for this? Correct — the WH01X24378 uses a snap-on installation with no screws or hardware. To install, align the new knob with the flat side (D-shape) of the control shaft and push it straight down until it seats fully. The whole replacement typically takes under a minute. Just make sure the knob is fully seated and rotates through all positions with the correct detent clicks before you plug the appliance back in. The knob installs fine but my washer still doesn't change settings — what next? If the new knob is installed correctly (fully seated and rotates through positions with detent clicks) but changing the knob position doesn't change the cycle behavior, the underlying selector switch or control shaft has likely failed — not the knob. Common causes include the shaft spinning freely without engaging the switch inside (the shaft has stripped or broken), or the electrical selector switch itself has failed. In these cases, replacing just the knob won't fix the problem — the switch assembly behind the panel also needs to be replaced. Contact our support team with your model number for the correct switch part number. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from heat-resistant plastic to match the dimensions, D-shape shaft receiver, snap-on installation, and cycle selection function of the original WH01X24378 selector knob used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE04X28977 Dryer Genuine Door Switch The WE04X28977 is a genuine GE dryer door switch for GE and Hotpoint dryers, and also fits select Haier, Monogram, and Café models built on the GE platform. This small latch-style switch communicates with the control board when the door is fully closed, allowing the drying cycle to safely begin, and signals the control board to stop the cycle if the door is opened during operation. White in color, measuring approximately 3"H x 2"W, weighing about 1 lb. Also known by the part number WE10X23879. Over time, this switch can become damaged from extended use or excessive force when closing the door. Symptoms of a failing door switch include the dryer failing to start, or the door not closing or latching properly. Replacing this switch requires a few basic tools and some slight disassembly of the dryer. It directly replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948. Quick Answer The WE04X28977 Dryer Genuine Door Switch fixes GE, Hotpoint, Haier, Monogram, and Café dryers that won't start or have a door that won't close or latch properly. White, small latch style, ~3"H x 2"W, ~1 lb. Replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948. This is a dryer part — it's sold individually and typically requires removing the front panel for access. Common Problems This Part Fixes Dryer won't start Door won't close or latch properly Dryer stops mid-cycle when the door is bumped or jostled Switch damaged from excessive force when closing the door Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer door switch directly replaces the following OEM and cross-reference part numbers: WE04X28977, WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select GE dryers, and also fits select Hotpoint, Haier, Monogram, and Café dryers built on the GE platform, including model numbers such as GTD42GASJ2WW, GTD45EASJ1WS, GTD45EASJ0WS, GTD45EASJ2WS, GTD42EASJ1WW, GTD42GASJ1WW, GTD72EBSN0WS, GTX22GASK0WW, GTD45GASJ2WS, GTD45GASJ1WS, GTX22EASK0WW, GTD42EASJ2WW, GTD42EASJ0WW, GTD42GASJ0WW, GTD72EBPN0DG, GTD45GASJ0WS, PTD60EBPR0DG, YTD74E2SN0WS, YTD74E2PN0DG, GTD84ECPN1DG, GTX52GASP0WB, PTD60GBSR0WS, GTD84GCPN0DG, VTD52EASR0WB, GTD84GCPN1DG, GTD84ECPN0DG, YTD74G2PN1DG, GTD84GCSN0WS, YTD74G2PN0DG, PTD60EBSR0WS, YTD74E2PN1DG, PTD60GBPR0DG, YTD74E2SN1WS, GTD84GCSN1WS, GTD65EBSJ4WS, VTD52GASR0WB, GTD84ECSN0WS, YTD74G2SN0WS, GTD84ECSN1WS, YTD74G2SN1WS, GTX52EASP0WB, HTX24GASK0WW, HTX24GASK0WS, HTX21EASK0WW, HTX21PASK0WW, HTX24EASK0WS, HTX24EASK0WW, HTX21GASK0WW, GTX65EBSJ2WS, GTD75ECPL0DG, GTD75GCPL0DG, GTD65GBSJ4WS, GTX42GASJ1WW, GTX65GBSJ2WS, GTD33PASK0WW, GTX33EASK0WW, GTX33GASK0WW, GTX60EBSJ0WS, GTD65EBSJ0WS, GTD65EBSJ3WS, GTX42EASJ1WW, 5TX62E9ST0WS, 5TX62E9ST1WS, 5TX62G9ST0WS, and ETD48EASW0WB. Note: This is a dryer part, sold individually. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified switch design Small latch-style door switch — communicates door status to the control board Resolves "won't start" and "door won't close" symptoms caused by switch failure White, approximately 3"H x 2"W, about 1 lb Also known as WE10X23879 Direct drop-in replacement matching the original mounting Replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948 Compatible with GE, Hotpoint, Haier, Monogram, and Café dryers Genuine OEM replacement — guaranteed fit, materials, and performance Sold individually Product Specifications Part Number WE04X28977 Also Known As WE10X23879 Part Type Dryer Door Switch (Small Latch Style) Condition Genuine OEM Brand GE Color White Height Approx. 3" Width Approx. 2" Weight Approx. 1 lb Repair Difficulty Easy to Moderate — front panel removal required Quantity 1 door switch (sold individually) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Turn the two screws located at the bottom corners of the front panel counter-clockwise until they come out, then slide the panel up and off the dryer to access the door switch. Locate the wires connected to the old door switch and disconnect them, noting their positions. Remove the mounting screws or clips securing the old switch and pull it free. Install the new WE04X28977 in the same position, reconnect the wires to their original positions, and secure the mounting hardware. Slide the front panel back into place and secure the two bottom corner screws. Restore power and test that the dryer starts normally with the door closed, and stops if the door is opened during a cycle. Tools needed: screwdriver, wrench, pliers. Frequently Asked Questions My dryer won't start. Is this the part I need? Yes, this is one of the most common symptoms of a failed door switch. Since this switch tells the control board whether the door is closed, a damaged or malfunctioning switch can prevent the dryer from starting even when the door is fully shut. My dryer door won't close properly. Could this be the same part? Yes, a damaged door switch — often from excessive force when closing the door over time — can cause the door to not latch or close correctly, in addition to preventing the dryer from starting. Is this a difficult repair? It's a straightforward repair for a confident DIYer, requiring a screwdriver, wrench, and pliers, along with some slight disassembly of the dryer's front panel to access the switch. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original switch design and mounting configuration of the door switch originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less