285751 Washer Genuine Agitator Dog Cam Kit
Replaces Part Numbers: 285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624.
Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO AGM30045804 Dryer Thermostat Kit
The XPARTCO AGM30045804 is an aftermarket replacement high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does.
Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335. As an aftermarket replacement, the AGM30045804 kit is built to OEM-equivalent quality standards.
Quick Answer
The XPARTCO AGM30045804 Dryer Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step.
What's In The Kit
Component
Function
High-Limit Thermostat
Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools.
Thermistor (with wire harness)
Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle.
Common Problems This Kit Fixes
Dryer overheating, sometimes scorching or damaging clothing
Dryer running with little or no heat
Inconsistent drying times — cycle shuts off too early or runs longer than necessary
Temperature-related error code displayed on the control panel
Clothes remaining damp after a full drying cycle
High-limit thermostat that keeps tripping repeatedly
Dryer that has already had its high-limit thermostat replaced once but the problem returned
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers:
AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335, AGM75510744, EAP16746326, PD00083166, ALG53211, AP7195784, PS16746326.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform.
Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order.
Key Features
Aftermarket replacement built to match LG's factory-specified resistance values and switch thresholds
Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit
Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms
Thermistor ships with its wire harness included
High-limit thermostat resets automatically after tripping — no replacement needed after each trip
Direct drop-in replacement for both original components
Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335
Compatible with LG and select Kenmore and GE-branded LG-built dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
AGM30045804
Part Type
Dryer High-Limit Thermostat and Thermistor Kit
OEM Part Number
AGM30045804
Condition
Aftermarket Replacement
Brand
LG
Kit Contents
High-limit thermostat + thermistor with wire harness
Thermistor Location
Blower housing
High-Limit Thermostat Type
Automatically resetting
Repair Difficulty
Easy to Moderate — 30 to 60 minutes
Compatible Brands
LG, select Kenmore, GE (LG-built models)
Installation Notes
⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead?
This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit.
What's the difference between the thermistor and the high-limit thermostat?
The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating.
My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing?
Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the resistance values, switch threshold, and wire harness configuration of the original AGM30045804 high-limit thermostat and thermistor kit used in compatible LG, Kenmore, and GE-branded LG-built dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
CIM15 Ice Maker (Copper) 15 Feet Copper Tubing and Self Tapping Saddle Valve
Includes 15' 1/4" copper tubing, self tapping saddle valve and compression fitting.
Low lead valve and fittings.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W11130359 Washer Suspension Rod Kit – Compatible with Whirlpool, Maytag, Amana, Crosley, and Roper Washers
Product Description
Reduce vibration and restore smooth, stable operation with the XPARTCO W11130359 Washer Suspension Rod Kit. This high-quality aftermarket replacement supports the washer tub and absorbs movement during wash and spin cycles. Worn or broken suspension rods can cause loud banging noises, excessive shaking, or unbalanced loads. Replacing them with this reliable XPARTCO kit ensures balanced performance and extends the life of your washer.
Replaces Part Numbers
W11130359, W11027215, 4813873, W10594082, W10785954, W10821704, W10901060, W11033536, W11226784, AP6261901, PD00042502, EAP12347544, PS12347544.
Compatibility
This replacement suspension rod kit fits select Whirlpool, Maytag, Amana, Crosley, and Roper top-load washers.
Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC565FW0, and Amana NTW4516FW3.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Built to match OEM performance and stability
🌀 Reduces Vibration – Keeps washer tub balanced during spin cycles
💰 Cost-Effective Solution – High-quality kit at a lower cost than OEM parts
🛠️ Complete Kit – Includes four suspension rods, bushings, and suspension springs
🛡️ Fixes Common Issues – Solves excessive shaking, banging, or unbalanced load problems
📐 Product Specification
Part Number: W11130359
Component Type: Washer Suspension Rod Kit
Includes: 4 suspension rods with springs and mounting bushings
Material: Heavy-duty steel with corrosion-resistant coating
Mounting: Direct-fit installation under washer tub
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, pliers, socket wrench
⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock or injury.
Steps:
Disconnect power and remove the washer lid or top panel.
Support the washer tub with a sturdy object or strap.
Remove the old suspension rods from their mounting holes.
Install the new XPARTCO W11130359 rods one by one, attaching springs and bushings.
Reassemble panels, plug in the washer, and run a test cycle to confirm smooth operation.
⏱️ Time Required: 30–40 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Eliminate noise and vibration — Add to Cart Now for a stable, long-lasting repair!
8270020CM Dishwasher Door Spring
Door balance spring - 7.75" overall length.
Fits Whirlpool dishwashers.
Replaces Part Numbers:WP8270020, 8270020, AP6012319, PS11745526.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
(8 Pack) 3977394 Dryer Thermal Cut-Off Kit – Replaces 3977394 – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers
Product Description
Protect your dryer from overheating with the 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable 3977394 kit restores safe temperature control and helps prevent damage to internal components.
Replaces Part Numbers
XPTC352, 3977394, 352F
Compatibility
This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers.
Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM safety and temperature performance
🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats
💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits
🛠️ Easy Installation – Direct-fit design with included thermostats and connectors
🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely
📐 Product Specification
Part Number: 3977394
Component Type: Dryer Thermal Cut-Off Kit
Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors
Temperature Rating: Cut-off opens at ~352°F.
Material: Metal thermostat housing and heat-resistant components
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Nut driver, Phillips screwdriver
⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock.
Steps:
Disconnect power and remove the rear dryer panel.
Locate the heating element housing and identify the cut-off and thermostat.
Disconnect wires and remove the old components.
Install the new 3977394 cut-off and thermostat in the same locations.
Reconnect wires, reassemble the back panel, and restore power.
Run a short test cycle to verify proper heating.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!
XPARTCO 279393 Dryer Terminal Block Screw Kit
The XPARTCO 279393 is an aftermarket replacement terminal block screw kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, and Norge. The terminal block screws secure the dryer power cord wires to the terminal block — the connection point where 240V power enters the dryer. Loose, corroded, or damaged screws at this connection can cause intermittent power loss, blown fuses, tripped breakers, or dangerous arcing.
This kit includes 3 chrome-plated screws and 3 nuts — everything needed to restore a secure, conductive connection at the terminal block. The chrome plating improves electrical conductivity and corrosion resistance. Screws measure 7/16" L x 7/16" W x 11/16" H; nuts measure 1/2" L x 1/2" W x 1/8" H. Installs in under 15 minutes with basic hand tools.
Quick Answer
The XPARTCO 279393 Terminal Block Screw Kit fixes electric dryers with intermittent power, blown fuses, tripped circuit breakers, hot terminals, or visible arcing and scorching at the power cord connection. Includes 3 chrome-plated screws and 3 nuts. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more.
Common Problems This Part Fixes
Dryer has intermittent power or will not start at all
Internal fuses repeatedly blowing without another clear cause
Circuit breaker for the dryer repeatedly tripping
Terminal block area is hot to the touch during or after operation
Visible arcing, sparks, scorch marks, or smoke around the terminal block cover
Heating element or motor works intermittently but not consistently
Dryer power cord connection is loose, corroded, or visibly damaged
Replaces Part Numbers
This terminal block screw kit directly replaces the following OEM and cross-reference part numbers:
279393, 279393D, 279393VP, 3184, EAP334188, AWP39844, PD00003883, AH334188, EA334188, AP3020386, PS334188
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This terminal block screw kit is compatible with select electric dryers from the following brands:
Whirlpool electric dryers
Kenmore / Sears electric dryers (Whirlpool-built models)
Maytag electric dryers
KitchenAid electric dryers
Amana electric dryers
Roper electric dryers
Admiral electric dryers
Estate electric dryers
Crosley electric dryers
Inglis electric dryers
Magic Chef, Norge, and Jenn-Air electric dryers
Note: This kit is for electric dryers only. Gas dryers do not use a terminal block for power cord connections.
Key Features
Secures the dryer power cord wires to the terminal block for a safe, reliable 240V connection
Kit includes 3 screws and 3 nuts — one complete set for all three terminal positions
Chrome-plated metal construction — improves electrical conductivity and resists corrosion
Screw dimensions: 7/16" L x 7/16" W x 11/16" H; Nut dimensions: 1/2" L x 1/2" W x 1/8" H
Direct replacement for OEM part numbers 279393, 279393D, and 279393VP — no modification required
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in under 15 minutes with basic hand tools
Product Specifications
Part Number
279393
Part Type
Terminal Block Screw and Nut Kit
Condition
Aftermarket Replacement
Application
Electric Dryers (240V terminal block)
Kit Contents
3 chrome-plated screws and 3 nuts
Screw Dimensions
7/16" L x 7/16" W x 11/16" H
Nut Dimensions
1/2" L x 1/2" W x 1/8" H
Material
Chrome-plated metal
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, Norge, Jenn-Air
Dryer Type
Electric dryers only
⚠️ Electrical Safety Warning This kit connects the power cord to the dryer's terminal block — a high-voltage connection carrying 240V. Always unplug the dryer and shut off the circuit breaker before beginning installation. Loose or improperly tightened terminal screws can cause arcing, overheating, blown fuses, or fire. If you are not comfortable working with high-voltage electrical connections, have this part installed by a qualified appliance technician.
Installation Notes
⚠️ Unplug and Switch Off Breaker Before Starting Unplug the dryer from the wall outlet and turn off the circuit breaker for the dryer before beginning any work on the terminal block. Locate the terminal block cover plate on the back of the dryer and remove it by unscrewing the retaining screw. Use needle-nose pliers to carefully disconnect the power cord wires from the terminal block. Remove the old screws and nuts using a Phillips or flat-head screwdriver. Install the new 279393 screws and nuts into the terminal block. Reconnect the power cord wires to the correct terminals — refer to the label inside the terminal block cover or your dryer's wiring diagram to confirm wire positions. Tighten all screws firmly but do not overtighten. Replace the terminal block cover plate. Restore power and run a test cycle to verify correct operation. Tip: While the cover is off, inspect the terminal block itself (part 694431) for burn marks or damage. If the block is damaged, replace it before reinstalling. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers.
Frequently Asked Questions
What is the terminal block screw kit used for?
The terminal block screw kit secures the three wires of the dryer's power cord (two hots and a neutral, or two hots and a ground depending on cord type) to the terminal block at the back of the dryer. This is the point where 240V power enters the machine. The screws must be firmly tightened to maintain a safe, low-resistance electrical connection. If they loosen or corrode over time, resistance increases at the connection — causing heat, arcing, blown fuses, or power loss.
Can I also use this kit when installing a new dryer power cord?
Yes — this kit is commonly needed when installing a new 3-wire or 4-wire dryer power cord. When switching from a 3-wire to 4-wire cord (or vice versa), the terminal block screws and nuts often need to be loosened and retightened, and replacing them with a fresh set ensures a secure, corrosion-free connection from the start.
Should I also inspect the terminal block itself?
Yes. While the terminal block cover is off, inspect the block itself (part 694431) for burn marks, melted plastic, or damaged terminals. If the block shows any of these signs, it should be replaced before reinstalling — new screws alone cannot fix a damaged terminal block. Contact our support team to find the correct terminal block for your model.
Does this kit work for gas dryers?
No. Gas dryers use a standard 120V three-prong household plug and do not have a terminal block for power cord connections. The 279393 kit is for electric dryers only, which use a 240V outlet and require a hard-wired terminal block connection for the power cord.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from chrome-plated metal to match the dimensions and electrical performance of the original 279393 screw kit.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag
Product Description
Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts.
Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures.
Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW
Kenmore: 110.60022010, 110.70102312, 110.78002012
Maytag: MEDC215EW1, MGDX655DW1
Roper: RED4640YQ0
Estate: EED4400WQ0
KitchenAid: YKEHS01PMT0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers.
🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F).
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes.
🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start.
Product Specification
Part Number: 279769
Component Type: Dryer thermostat kit
Material: Metal and plastic
Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16)
Weight: 2.4 oz (Based on web:1, web:15)
Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C)
Mounting: Screw-mounted on heater housing.
Operating Conditions: Suitable for high-heat dryer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today!
Add to cart now for a budget-friendly fix!
EXP651 Dryer Belt and Idler Pulley Kit Replaces WPW10112954, W10837240
The EXP651 is an aftermarket dryer repair kit containing two essential drum drive components for select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The kit includes one drum belt (replaces WPW10112954) and one idler pulley assembly with bracket (replaces W10837240) — the two parts most commonly worn together when a dryer drum stops spinning or becomes noisy.
Replacing both the belt and idler pulley at the same time is the smart repair choice. Since the dryer must be disassembled to access either part, doing both in one repair saves you from having to take the machine apart again if the second part fails shortly after. This kit covers the two most common failure points in the Whirlpool-family dryer drum drive system.
Quick Answer
The EXP651 Dryer Belt and Idler Pulley Kit fixes dryers where the drum is not spinning, making loud squeaking or grinding noises, or the belt has broken. Includes one 93-1/4" x 5/16" 5-rib drum belt (WPW10112954) and one idler pulley assembly with bracket (W10837240). Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers.
What's in the Kit
Part 1 of 2
Dryer Drum Belt — Replaces WPW10112954
93-1/4" L x 5/16" W x 1/8" H · 5-rib Multi-V rubber belt · Wraps around drum and connects to motor and idler pulleys to drive drum rotation
Part 2 of 2
Idler Pulley Assembly with Bracket — Replaces W10837240
2-1/8" pulley diameter · 6-1/4" L x 1-1/4" W x 3-7/16" H overall · Plastic/metal construction · Maintains correct belt tension to spin the drum · Fits Whirlpool dryers with lint screen inside door
Common Problems This Kit Fixes
Dryer drum not spinning — motor runs but drum stays still
Loud squeaking, squealing, or grinding noise during operation
Clothes not tumbling during the drying cycle
Thumping or slapping noise when dryer is running
Belt slipping off or repeatedly breaking
Burning rubber smell coming from the dryer
Dryer drum turning erratically or stopping while motor continues to run
Replaces Part Numbers
Drum Belt (WPW10112954) cross-references:
WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388.
Idler Pulley Assembly (W10837240) cross-references:
W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, AWP41730, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244.
If your part numbers are not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select dryers from the following brands:
Whirlpool dryers (gas and electric — fits models with lint screen inside door)
Maytag dryers (gas and electric)
Amana dryers
Kenmore / Sears dryers (select Whirlpool-built models)
KitchenAid dryers
Crosley dryers
Admiral dryers
Inglis dryers
Roper dryers
Note: The W10837240 idler pulley fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley part number may be required. Contact our support team to confirm before ordering.
Key Features
Two-part kit covers the most common drum drive failures in Whirlpool-family dryers in a single repair
Belt: 93-1/4" L x 5/16" W, 5-rib Multi-V rubber — resists cracking, stretching, and heat damage
Idler pulley: 2-1/8" diameter pulley with arm and bracket — maintains correct belt tension for smooth drum rotation
Replacing both parts together saves a second disassembly if the other part fails soon after
Aftermarket replacement built to OEM-equivalent quality standards
Belt directly replaces WPW10112954 / W10112954 — no modification required
Idler pulley directly replaces W10837240 / W10547287 / W10547290 — no modification required
DIY-friendly repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Kit Part Number
EXP651
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Kit Includes
1x Drum Belt (WPW10112954), 1x Idler Pulley Assembly with Bracket (W10837240)
Belt Length
93-1/4 inches
Belt Width
5/16 inch
Belt Height
1/8 inch
Belt Ribs
5 ribs, 4 grooves (Multi-V)
Belt Material
Rubber
Pulley Diameter
2-1/8 inches
Pulley Overall Dimensions
6-1/4" L x 1-1/4" W x 3-7/16" H
Pulley Material
Plastic / Metal
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper
Installation Notes
⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension at the old idler pulley, lift the drum slightly, and slide the old belt off. Remove the old idler arm assembly by unscrewing the mounting screw, then install the new W10837240 idler pulley assembly and secure with the screw. Loop the new WPW10112954 belt around the drum with the ribbed side facing inward, then route it around the new idler pulley and motor pulley. Consult your model's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tools needed: Phillips screwdriver, putty knife or flat pry tool.
Frequently Asked Questions
Why should I replace the belt and idler pulley at the same time?
The belt and idler pulley wear together — when one fails, the other is usually close behind. Since the dryer must be fully disassembled to access either part, replacing both in a single repair saves you from having to take the machine apart again soon after. It also protects the new belt from being damaged by a worn pulley, and vice versa.
How does the W10837240 differ from other Whirlpool idler pulleys?
The W10837240 is the updated idler pulley arm and bracket assembly designed for Whirlpool-family dryers that have the lint screen inside the door. It replaces the older W10547287 and W10547290 assemblies. Some older or different Whirlpool models use a different idler pulley style — if you're unsure which one your dryer needs, contact our support team with your model number before ordering.
What is the difference between WPW10112954 and W10112954?
These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954. Both refer to the identical drum belt included in this kit.
Should I also replace the drum rollers at the same time?
It depends on the condition of your rollers. Since the dryer is already fully disassembled, it is a good opportunity to inspect the drum support rollers for flat spots, cracks, or wobbling. If they show any wear, replacing them at the same time is recommended to avoid a third disassembly. Check your model's roller part number before ordering.
Are these OEM or aftermarket parts?
Both parts in this kit are aftermarket replacements built to OEM-equivalent quality standards. They are not genuine Whirlpool OEM parts, but are manufactured to match the dimensions and performance of the original WPW10112954 belt and W10837240 idler pulley assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 330031 Surface Burner Receptacle Kit – Compatible with Whirlpool, Maytag & Kenmore Ranges
Product Description
Restore reliable burner operation and eliminate heating issues with the XPARTCO 330031 Surface Burner Receptacle Kit. This high-quality aftermarket replacement kit includes a surface element receptacle block with high-temperature wire leads, designed to deliver proper power to electric range burners. A worn or burned receptacle can cause burners not to heat, heat intermittently, or spark. Replacing it with this durable XPARTCO kit ensures a secure electrical connection and dependable cooking performance.
XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price.
Replaces Part Numbers
This kit replaces part numbers 330031, AP3075808, W10841094, 14200040, 14200233, 14203070, 14205001, 14205727, 14209631, 14210007, 14254131, 3374, 42147, 42153, 4335480, 5303935058, 550226, 71930, 74-06-132, 74-06-190, 766339, 99989649, 9E28000199, AH340571, EA340571, FSP330031, PS340571, R0157526, R0167091, R300, TS300, W10116799, W10116803, WB17X210, Y0042147, Y0042153, Y0045536, Y0045546, Y0051088, Y0054794, Y0067069, Y0071930, Y0071931, Y0075054, Y0086726, Y0088866, Y0089227, Y0089291, Y0089336, Y0090094, Y0300678, Y0308306, Y89336, YC2711501, YC2716501, YR0181149, 5303935058, 5301167733, 08002879, 08002916, 08002917, 08002918, 08002919, 08008697, 08011962, 08012830, 08012865, 09957075, 12871, 318112500, 318366400, 42822, 53-003, 709T026P01, 709T026S01, 709T026S02, 709T034P01, 709T045P01, 868464, 9175, A1505240, A1505979, G54972, G55667, K001167470, K001315483, K001319226, K1167204, K1167205, K1167470, K1310415, K1311332, K1312169, K1312179, K1312800, K1315200, K1315483, K1319226, K1323982, K5043104, K5043105, K5137801, PS470125, R201A, RR104, RR109, RR110, RR117, S5303310284, AP2591744, WB17X5091, AP2021538, 245919, AH232634, EA232634, PS232634, R117.
Compatibility
This replacement surface burner receptacle kit fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper electric ranges.
Commonly used on 6-inch and 8-inch surface elements.
Always verify your range’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement Kit – Matches OEM fit and electrical performance
🔥 High-Temperature Receptacle – Designed for repeated heating cycles
🔧 Includes Wire Leads – Complete repair solution
⚡ Improves Electrical Contact – Restores consistent burner heating
💰 Cost-Effective Repair – Reliable alternative to OEM kits
📐 Product Specification
Part Number: 330031
Component Type: Surface Burner Receptacle Kit
Includes: Receptacle block with high-temp wires and two mounting bracket.
Application: Electric range surface burner connection
Voltage: 240V
Mounting: Plug-in / screw-mounted (model dependent)
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, wire cutters/strippers
⚠️ Safety First: Disconnect power at the breaker before servicing the range to avoid electrical shock.
Basic Steps:
Turn off power to the range at the breaker.
Remove the burner element and access the receptacle.
Disconnect the old receptacle and cut damaged wires if needed.
Connect the new XPARTCO 330031 receptacle using approved wire connectors.
Secure the receptacle and reinstall the burner element.
Restore power and test burner operation.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore safe, consistent burner heating — Add to Cart Now for a dependable, budget-friendly repair!
279311 Genuine OEM Dryer Igniter Kit and Bracket - Compatible with Whirlpool, Maytag, Kenmore
Product Description
Restore your gas dryer’s heating performance with the 279311 Genuine OEM Dryer Igniter Kit and Bracket. This Whirlpool-manufactured kit includes a silicon carbide igniter, ceramic holder, bracket, wire leads, and plug, designed to ignite the gas burner in select Whirlpool, Maytag, Kenmore, and other compatible gas dryers. It addresses issues like no heat, intermittent heating, or prolonged drying times, ensuring efficient operation. Handle with care, as the igniter is fragile.
Note: Includes (1) igniter kit with bracket, wire leads, and plug. Disconnect power and gas supply before installation. Verify compatibility with your dryer model.
Replaces part numbers: 279311, 239233, 239300, 239302, 26000279311, 279185, 279311VP, 338899, 338900, 3389895, 340607, 3415, 343128, 41-311, 6-85211, 660991, 685211, 686590, 687399, 691039, 8113, 99912719, AH334180, DE351, DE354, DE363, PD00002344, EAP334180, EA334180, K35-166, AP3094138, PS334180.
Compatibility:
Compatible with select gas dryer models, including but not limited to:
Whirlpool: CG1751XWN0, CG1751XWW0, CG2101XMW0, CG2501XMW0, WGD4910XQ1
Maytag: MGDX655DW, MGDC415YW0, MGD6000BW0
Kenmore: 110.97591420, 110.97591220, 110.97592420
Amana: NGD4655EW0
Roper: RGD4515EW0
Common models: Whirlpool WGD4815EW, Maytag MGD3500FW0, Kenmore 110.97561601
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, Roper, and other gas dryers.
🔧 Specifications: Genuine OEM Whirlpool silicon carbide igniter with ceramic holder, bracket, wire leads, and plug.
💪 Reliable Performance: Ignites gas burner for consistent heating, ensuring efficient drying.
🛠️ Easy Installation: Requires a screwdriver, nut driver, and pliers; typically installed in 20–30 minutes.
🛡️ Effective Fixes: Resolves no heat, intermittent heating, thermal fuse tripping, or prolonged drying times.
Product Specification
Part Number: 279311
Component Type: Gas dryer igniter kit
Material: Silicon carbide igniter with ceramic holder and metal bracket
Operating Conditions: Suitable for gas dryer burner assemblies, 120V
Compliance: UL-listed, Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source and gas supply before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer heating efficiently today!
Add to cart now for a reliable fix!
