Search results for "dishwasher water"

W11434044 Genuine OEM Whirlpool Dishwasher Water Inlet Valve The W11434044 is a Genuine OEM Whirlpool replacement dishwasher water inlet valve assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, and Caloric dishwashers. The water inlet valve is mounted at the base of the dishwasher and connects to the household cold water supply line. When the control board calls for water during the fill cycle, the valve's internal solenoid opens, allowing water to flow into the tub. The valve closes the instant the control board cuts power, stopping flow precisely when the correct water level is reached. Without a properly functioning inlet valve, the dishwasher can't get water into the tub — meaning it can't wash, rinse, or complete a cycle. Rated 120V AC, 50/60Hz, 6/5W. Approximate dimensions: 2.9" H x 2.3" W with a 0.9" threaded orifice for the water supply connection. The package includes the water inlet valve, water outlet pipe (inlet hose), and two hose clamps — everything needed for the connection between the valve and the dishwasher's water divider. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11434044 directly replaces W11187724, W11025972, W11025970, AWP44732, AP6987233, and PS16217908. Important: the water inlet connection uses plastic threads, which are easily damaged by over-tightening or cross-threading — hand-tighten the water line carefully during installation. Installs in 30–45 minutes with basic hand tools. Quick Answer The W11434044 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Maytag, KitchenAid, JennAir, and Kenmore dishwashers that aren't filling with water, fill slowly, aren't washing properly, drain immediately after filling, or leak at the valve. 120V AC, 50/60Hz, 6/5W. Approximately 2.9"H x 2.3"W. Genuine OEM. Includes inlet valve, water outlet pipe, and 2 hose clamps. Replaces W11187724, W11025972, W11025970, AWP44732, AP6987233, PS16217908. Compatible with WDT750SAKZ, KDTM404KPS, MDB4949SKZ, WDTA50SAKZ, KDTE204KPS, WDPA70SAMZ, WDPS7024, WDT740SAL, WDT751SAP, WDT970SAK series and related models. Plastic-thread inlet connection — hand-tighten carefully to avoid stripping. Common Problems This Part Fixes Dishwasher not filling with water — valve solenoid not opening when commanded Dishwasher filling too slowly — valve partially clogged with sediment or weak solenoid Dishes not being washed properly due to insufficient water fill Dishwasher fills but doesn't reach normal water level Water leaking from the valve body or its connections Dishwasher continuously running water even when the cycle should be complete — valve stuck open Dishwasher won't advance past the fill phase due to insufficient water detection Excessive cycle times as the dishwasher tries to fill from a partially clogged valve Multimeter test on the valve solenoid shows no continuity Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11434044, W11025970, W11025972, W11187724, AP6987233, AWP44732, EAP16217908, PD00064823, PS16217908. W11434044 is the current OEM production part superseding W11187724, W11025972, and W11025970. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: Whirlpool dishwashers — WDPA70SAMZ0, WDPA70SAMZ2, WDPA70SAMZ3, WDPS7024RV0, WDPS7024RZ0 series Whirlpool dishwashers — WDT740SALB2, WDT740SALB3, WDT740SALW2, WDT740SALW3, WDT740SALZ3 series Whirlpool dishwashers — WDT750SAKB0/B2/B3, WDT750SAKV0/V2/V3, WDT750SAKW0/W2/W3, WDT750SAKZ0/Z2/Z3 series Whirlpool dishwashers — WDT751SAPZ0, WDT751SAPZ1 series Whirlpool dishwashers — WDT970SAKV2, WDT970SAKV3, WDT970SAKZ2, WDT970SAKZ3 series Whirlpool dishwashers — WDTA50SAKB0/B2/B3, WDTA50SAKT0/T2/T3, WDTA50SAKV0/V2/V3, WDTA50SAKZ0/Z2/Z3 series KitchenAid dishwashers — KDTM404KPS, KDTE204KPS and related models Maytag dishwashers — MDB4949SKZ and related models JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, Caloric — select Whirlpool-built dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles Solenoid-actuated — opens precisely when the control board calls for water and closes the moment the call is dropped 120V AC, 50/60Hz, 6/5W — correct electrical specifications for compatible Whirlpool-platform dishwashers Dimensions: approximately 2.9" H x 2.3" W · 0.9" threaded orifice diameter Includes water inlet valve, water outlet pipe (inlet hose), and 2 hose clamps for a complete connection set Current OEM production part — supersedes W11187724, W11025972, and W11025970 Also replaces AWP44732, AP6987233, and PS16217908 Compatible with Whirlpool WDT740SAL, WDT750SAK, WDT751SAP, WDT970SAK, WDTA50SAK, WDPA70SAMZ, WDPS7024 series and select KitchenAid, JennAir, Kenmore, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, and related Whirlpool-built dishwashers DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W11434044 Supersedes W11187724, W11025972, W11025970 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Voltage 120V AC Frequency 50/60 Hz Wattage 6/5W Dimensions Approximately 2.9" H x 2.3" W Threaded Orifice Diameter 0.9" Inlet Thread Material Plastic (hand-tighten carefully to avoid stripping) Body Material ABS Plastic / Stainless Steel Includes 1x Inlet Valve, 1x Water Outlet Pipe, 2x Hose Clamps Compatible Brands Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, Caloric Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves — DON'T OVER-TIGHTEN PLASTIC THREADS Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Have towels ready — residual water remains in the supply line and will spill when disconnected. Critical: the W11434044's water supply connection uses plastic threads. Multiple installers have reported stripping the plastic threads by over-tightening or cross-threading the water line during installation — always hand-tighten the fitting carefully and align the threads squarely before tightening. If your dishwasher is installed under a counter, working through the lower access panel is possible but tight — many installers find it easier to pull the dishwasher partially out from the cabinet, or lay it on its side, to reach the inlet connection cleanly (this also lets you use a 90-degree hose fitting without cross-threading). Remove the lower access panel (typically 2 screws) at the front bottom of the dishwasher. Locate the water inlet valve. Photograph the wire harness and hose connections before disconnecting anything. Disconnect the household water supply line from the valve. Squeeze the hose clamps with pliers and slide them back to release the outlet hose from the valve, then disconnect the wire harness plug. Remove the mounting screws holding the valve in place. Install the new W11434044 valve, secure the mounting hardware, and reconnect the outlet hose and hose clamps. Push the electrical connector's fixing plate firmly into place before connecting the wire harness plug — this prevents the connector from falling out during operation. Reconnect the household water supply — hand-tighten the fitting carefully to avoid stripping the plastic threads. Restore water and power. Run a test cycle and check for leaks at all connections. Tools needed: Phillips screwdriver, adjustable wrench (used lightly on plastic threads only!), channel-lock pliers, work gloves, safety glasses. Frequently Asked Questions My dishwasher isn't filling with water — is the inlet valve the problem? Very likely, yes — that's the most common symptom of a failed dishwasher water inlet valve. Before replacing, do a few quick checks: 1) confirm the household water supply to the dishwasher is turned on at the shutoff valve; 2) check the household water pressure at a nearby fixture (a nearby faucet) to make sure your home has normal pressure; 3) inspect the inlet screen on the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean but the dishwasher still won't fill, the W11434044 valve solenoid has likely failed and replacing it will resolve the issue. You can also test the solenoid with a multimeter — no continuity means the solenoid has burned out. What is the difference between W11434044 and W11025970/W11025972/W11187724? These are the same water inlet valve across production revisions. W11025970 was the original OEM part number, W11025972 and W11187724 were mid-generation revisions, and W11434044 is the current OEM production version. All are physically and functionally interchangeable — if your dishwasher's parts diagram or the part on your appliance shows any of these numbers, the W11434044 is the correct current replacement, and this listing covers all of them. Why is over-tightening the water line connection such a common issue? The water supply inlet on the W11434044 has plastic threads to reduce cost and simplify manufacturing — but plastic threads are much less forgiving than brass or metal fittings. Cross-threading (starting the fitting at an angle instead of straight-in) or applying too much torque with a wrench will strip the plastic threads or split the fitting. Always align the water line fitting carefully by hand first, get several turns of engagement before applying any tool, and use only enough torque to snug the connection (typically hand-tight plus a very light quarter-turn with a wrench). If the threads are already stripped, the valve or a replacement plastic fitting will need to be ordered — the connection can't be repaired. Should I lay the dishwasher on its side for this repair? If you're finding it difficult to reach the water inlet connection cleanly through the lower access panel — which is a common complaint from installers — laying the dishwasher on its side (or pulling it partially out from the cabinet) makes the connection much easier to work with. This is especially helpful if your water supply line uses a 90-degree hose fitting that needs a straight approach for correct thread engagement. Before laying the dishwasher down, disconnect all connections and drain any residual water from the tub to avoid spills. Note that if the door has been damaged or bent, laying the unit on its side can worsen the damage — inspect first. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same water inlet valve installed in compatible Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, and related Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

AEC74337401 Dishwasher Water Inlet Guide - Compatible with LG Dishwashers Product Description Restore your dishwasher’s cleaning performance with the AEC74337401 Water Inlet Guide from Parts-O-Matic. This genuine OEM replacement guide directs water from the inlet valve into the dishwasher tub, ensuring proper water flow for wash and rinse cycles. Designed for LG dishwashers, it fixes issues like insufficient water, poor cleaning, or water inlet error codes.  Note: Includes one water inlet guide. Take photos of connections during disassembly and clean the inlet valve before installation. Replaces part numbers: AEC74337401, AP6233501, PD00056036, PS12078211. Compatibility: Compatible with models including but not limited to: Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand Compatibility: Fits select LG dishwasher models. 💧 Specifications: OEM plastic water inlet guide, designed for secure water flow and durability. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Reliable Fixes: Resolves insufficient water, poor cleaning, or water inlet error codes. Installation Notes: Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Clean the inlet valve and hose to prevent clogs. Access the inlet guide (inside or near the bottom of the dishwasher), disconnect the old guide, and install the new one, ensuring tight connections. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

Choice Manufactured Parts Choice 628334 Dishwasher Water Valve Replaces 10023852 Aftermarket dishwasher water inlet solenoid valve for select Bosch and Thermador dishwashers. Product Overview The Choice 628334 Dishwasher Water Valve is an aftermarket replacement water inlet solenoid valve designed for select Bosch and Thermador dishwashers. It replaces Bosch part 10023852 and earlier valve numbers including 00628334 and 628334. The valve controls the incoming household water supply during the dishwasher fill cycle. Quick Answer Choice part 628334CM is a dishwasher water inlet solenoid valve with a garden-hose-style inlet and push-on outlet hose connection. It replaces Bosch 10023852 on compatible Bosch and Thermador dishwashers. Common Problems This Part May Fix Dishwasher will not fill with water Dishwasher fills slowly or inconsistently Water inlet valve leaks Dishwasher continues to receive water when it should not Poor wash performance caused by insufficient fill Replaces and Cross-References 10023852, 00628334, 628334CM, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, OEM21579333, PD00075605, PS8729241 Cross-reference numbers are provided for identification. This is a Choice Manufactured Parts aftermarket replacement and is not a Genuine Bosch OEM part. Compatibility Designed for select Bosch and Thermador dishwashers. Compatible model examples include: SHE33T56UC/01 SHE53T52UC SHE53T55UC SHEM63W55N/01 SHP65T55UC/01 SHP68T55UC/01 SHS863WD5N/10 SHX68T55UC/01 DWHD440MFP Important: This is only a partial compatibility list. Verify the complete appliance model number and original valve part number before ordering. Key Features Choice Manufactured Parts aftermarket replacement Water inlet solenoid valve Garden-hose-style inlet connection Push-on outlet hose connection Replaces Bosch 10023852 For select Bosch and Thermador dishwashers Specifications Brand Choice Manufactured Parts Choice Part Number 628334CM Part Type Dishwasher Water Inlet Solenoid Valve Replaces 10023852 / 00628334 / 628334 Inlet Garden-hose-style connection Outlet Push-on hose connection Condition New Quality Aftermarket Replacement Installation Notes Disconnect electrical power to the dishwasher. Shut off the household water supply before disconnecting the inlet line. Use a towel or shallow pan for residual water in the line. Transfer hoses/connectors exactly as configured on the original valve. After installation, restore water and power and carefully inspect all connections for leaks. A no-fill condition can also be caused by a closed water supply, clogged screen, float/float switch problem, wiring issue, or control fault. Diagnose the appliance before replacing parts. FAQ Does Choice 628334 replace Bosch 10023852? Yes. Choice 628334CM is marketed as an aftermarket replacement for Bosch 10023852 and earlier 00628334 / 628334. Is this a Genuine Bosch OEM part? No. This is a Choice Manufactured Parts aftermarket replacement. Will it fit every Bosch dishwasher? No. Fitment is model-specific. Verify the full dishwasher model number and original valve number before ordering. Shop With Confidence Confirm your dishwasher model number before purchase. Compatibility assistance is available if you are unsure whether 628334CM / 10023852 is correct for your appliance. Choice ReplacementBosch / Thermador FitmentWater Inlet ValveCompatibility Support

Read more less

W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve The W10844024 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers. This valve regulates the flow of water into the appliance during each fill stage of the wash cycle, opening and closing to admit the correct amount of water at the right times. Weighing approximately 0.2 lbs, common failure causes include mineral or sediment buildup inside the valve and general electrical wear in the solenoid. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, or a valve that's unusually noisy — starting and stopping repeatedly — during heavy wash cycles as it struggles to regulate flow correctly. It directly replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 Quick Answer The W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers that aren't filling with water, or that are unusually noisy — starting and stopping — during heavy wash cycles. Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996. Some households need a separate hose adapter for this valve if the existing water line connector has a smaller diameter than the new valve's fitting — check before you start, or be prepared for a quick hardware store trip. Common Problems This Part Fixes Dishwasher not filling with water at all Valve unusually noisy — starting and stopping repeatedly during heavy wash cycles Cycle stalling at the fill step and never advancing to wash Poor washing results due to insufficient water fill Leaking near the valve connections Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W10844024, 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers built on the Whirlpool platform, including model numbers such as KUDR25SHWH1, MDB4629AWB1, DU900PWKB0, DU900PWKQ0, and Kenmore 665.15522000, 66517662991, and 66516669991. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher during each fill stage of the cycle Resolves "won't fill" and "noisy, starts and stops when filling" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996 Compatible with Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W10844024 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Weight Approx. 0.2 lbs Function Regulates water flow into the dishwasher during fill Repair Difficulty Easy to Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, Amana Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Check Your Hose Connector Size First Disconnect power at the outlet or shut off the circuit breaker, and disconnect the water lines connected to the old valve before beginning. Wear work gloves. Have a shop vacuum on hand — some customers have needed to remove standing water from the bottom of the dishwasher before starting this repair. Locate the old valve and use pliers to unscrew any screws or bolts connecting it to the appliance. Clean the area where the old valve was located, removing any debris before installing the new one. Check the diameter of your existing water line connector before starting — some households have a smaller-diameter connector than this new valve's fitting requires, in which case you'll need a separate hose adapter from a hardware store to complete the connection. Take the new W10844024 and place it in the same position as the old valve, making sure it's connected correctly, and secure any screws or bolts. Reattach the water lines to the new valve and reconnect power. Double-check all connections before restoring power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: pliers, possibly a hose adapter, shop vacuum (if needed), work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Will I need any extra parts for this installation? Possibly. A few customers have found their existing water line connector had a smaller diameter than this valve's fitting, requiring a separate hose adapter purchased locally from a hardware store to complete the connection. It's worth checking your connector size beforehand, or having a quick trip to the hardware store planned just in case. My dishwasher makes a noisy, start-and-stop sound when filling. Is that this valve? Yes, this is a documented symptom. One customer described their valve as "very noisy on heavy wash cycles, started and stopped when filling" before replacing it with this exact part, which resolved the issue. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

10023852 Genuine OEM Bosch Dishwasher Water Valve The 10023852 is a genuine Bosch OEM warm water inlet valve for Bosch, Thermador, Dacor, and Gaggenau dishwashers. This valve regulates the flow of warm water into the dishwasher during each wash cycle — a solenoid opens when the dishwasher calls for water and closes once the required amount has been reached, which is what prevents overfilling or underfilling and supports thorough cleaning performance. Rated 110-127V, 60Hz. Common causes of a bad valve range from mineral buildup due to hard water, which can obstruct the valve, to general mechanical wear and electrical problems that impair the valve's ability to open or close correctly. Symptoms of a failing valve include inadequate water filling the dishwasher, overfilling that can lead to leaks and water damage, unusual noises coming from the valve area, or the dishwasher failing to start. It directly replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. Quick Answer The 10023852 Genuine OEM Bosch Dishwasher Water Valve fixes Bosch, Thermador, Dacor, and Gaggenau dishwashers with inadequate water filling, overfilling, unusual noise near the valve, or a dishwasher that won't start. 110-127V, 60Hz. Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If you're also seeing a slow leak near the sump area, be aware that on some Bosch models the sump gasket is built into the sump itself rather than sold as a separate part — a leak there is a different repair from this valve. Common Problems This Part Fixes Inadequate water filling the dishwasher Overfilling, which can lead to leaks and water damage Unusual noises coming from the valve area Dishwasher failing to start Poor washing results due to insufficient water supply Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: 10023852, 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Bosch dishwashers, and also fits select Thermador, Dacor, and Gaggenau dishwashers built on the Bosch platform, including model numbers such as SHXM98W75N/01, SHX863WD5N/01, SHEM63W55N/01, and SHPM65Z55N/01, and spanning model series SHE, DWH, SHX, SHV, and SHP. Note: This valve is not universal — it's designed for specific Bosch, Thermador, Dacor, and Gaggenau models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Bosch OEM part — factory-specified solenoid design and flow rate Regulates warm water flow into the dishwasher during each wash cycle Resolves "won't fill properly," "overfilling," "unusual noise," and "won't start" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and connections Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241 Compatible with Bosch, Thermador, Dacor, and Gaggenau dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 10023852 Part Type Dishwasher Warm Water Inlet Valve Condition Genuine OEM Brand Bosch Voltage 110-127V Frequency 60 Hz Function Regulates warm water flow into the dishwasher during fill Repair Difficulty Easy to Moderate Quantity 1 valve Compatible Brands Bosch, Thermador, Dacor, Gaggenau Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. On many Bosch models, pulling the dishwasher out from under the counter gives the best access to the valve and surrounding sump area. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and water line from the old valve, remove its mounting hardware, and pull it free. Install the new 10023852 in the same position, reconnect the water line and electrical connector fully, and secure the mounting hardware. If you're troubleshooting a slow leak in this general area rather than a fill problem, be aware that on some Bosch models the sump gasket is built directly into the sump itself and isn't sold as a separate part — a leak there is a different repair involving the sump assembly (diverter, circulation pump, drain pump, and aqua-sensor) rather than this valve. Restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with enough water. Is this the right part? Yes, this is one of the most direct symptoms of a failed water inlet valve. Since this valve is what admits warm water from your household supply into the dishwasher, mineral buildup, mechanical wear, or an electrical fault can prevent it from opening fully, leaving the dishwasher without enough water for a proper wash. I have a slow leak near the bottom of my dishwasher. Is that this valve too? Not necessarily. One customer traced a slow, worsening leak on a Bosch dishwasher to the sump gasket, not the water valve — and found that on their model, the gasket is built into the sump itself rather than being a separately replaceable part, requiring a more involved repair pulling the sump apart to address it. If your leak is coming specifically from the sump area rather than showing up as a fill problem, it may be a different repair than this valve replacement. What causes this valve to fail over time? The most common cause is mineral buildup from hard water, which can gradually obstruct the valve's internal passages. Mechanical wear and general electrical problems can also affect the valve's ability to open and close correctly over years of use. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP DD62-00067A Dishwasher Water Valve Replaces Part Numbers:DD62-00067A, AP4341924, 1606674, PS4222444   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

DD31-00016B Dishwasher Drain Pump Motor - Compatible with Samsung Dishwashers Product Description Restore your dishwasher’s performance with the DD31-00016B Dishwasher Drain Pump Motor. This genuine OEM replacement pump ensures efficient water drainage during wash and rinse cycles, preventing water pooling and error codes. Designed for Samsung dishwashers. Replaces part numbers: DD31-00016B, AP7244901, PS17504318, EAP17504318, PD00089738. Verify your model number or contact support for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung dishwasher models. 💧 Specifications: OEM drain pump motor, 120V, 60Hz, 3.5" x 3.5" x 2.5", with plastic impeller and electrical connector for reliable drainage. DD31-00016B Motor Bldc PUMP; BD15-3C, 2800-3400RPM, 230 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves water pooling, poor drainage, or 5E/SE error codes. Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

WD19X25278 Dishwasher Diverter Assembly The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning. The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK. Quick Answer The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first. Common Problems This Part Fixes Water pooling or leaking underneath the dishwasher Poor washing performance from one or both spray arms Unusual noise during the wash cycle Water not properly directed to the correct spray arm Inconsistent cleaning results between the upper and lower racks Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers: WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB. Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement diverter assembly — controls water flow to the spray arms Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms Valve and float assembly engineered to optimize water flow while minimizing noise Direct drop-in replacement matching the original mounting and connections Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair Product Specifications Part Number WD19X25278 OEM Part Number WD19X25278 Part Type Dishwasher Diverter Valve Assembly Condition Aftermarket Replacement Function Controls water flow direction to the upper and lower spray arms Design Valve and float assembly Repair Difficulty Easy to Moderate — DIY-friendly Quantity 1 diverter assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions I'm seeing water pooling under my dishwasher. Is this the part I need? Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it. Any tips to avoid damaging the new part during installation? Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this. Is this a difficult repair? No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11087376 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers:W11087376, W10917114, 4534143, AP6237961, PS12074533. California Residents only WARNING: California’s Proposition 65 

Read more less

WD19X25278 Dishwasher Genuine OEM Diverter Assembly Replaces Part Numbers: WD19X25278, WD18X21678, 4922277, WD00X25260, AP6871922, PS12710077. Description: This Diverter Valve Assembly Kit serves a Genuine OEM replacement Part for specific GE dishwasher models. Its key function is to provide an alternative passage for water to reach the upper spray arms of the dishwasher. A faulty or damaged diverter valve often manifests as water leaks within the dishwasher. When such leaks occur and can be traced back to the diverter valve, this assembly kit offers a comprehensive solution. It includes all necessary components and fasteners to efficiently replace the valve. This kit is suitable for use with specific General Electric dishwasher models.

Read more less

A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line. Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535. Quick Answer The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause. Common Problems This Part Fixes Dishwasher won't drain at the end of the cycle Water pooling at the bottom of the tub after a completed cycle Grinding or humming noise coming from the pump area Dishwasher won't start a new cycle because it detects leftover water from the previous one Dishes not getting properly cleaned due to poor water circulation Pump running but producing little or no actual drainage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform. Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified motor speed and impeller design Pumps water out of the tub and through the drain hose at the end of each cycle Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure Includes pump motor, impeller, and seal Rated 120V, 60Hz, 35W, 0.8A, 3600RPM 1/4" male terminals for a direct plug-in electrical fit Direct drop-in replacement — no modification required Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number A00126401 Part Type Dishwasher Drain Pump Motor Assembly Condition Genuine OEM Brand Frigidaire Voltage 120V Frequency 60 Hz Wattage 35 W Amperage 0.8 A Motor Speed 3600 RPM Terminals 1/4" male Kit Contents Pump motor, impeller, seal Dimensions Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H Color White / Green Repair Difficulty Easy to Moderate — under an hour Quantity 1 drain pump motor assembly Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore Installation Notes ⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves. Frequently Asked Questions My dishwasher won't drain. How do I know if it's actually the pump and not something simpler? Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix. I already replaced the pump and it's still not draining. What should I check next? This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing. Does this kit include the check valve flapper? This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD31-00005A Dishwasher Drain Pump Motor The XPARTCO DD31-00005A is an aftermarket replacement drain pump motor for Samsung dishwashers. This pump uses an internal impeller to force wastewater out of the tub and through the drain hose during the drain phase of the wash cycle — it's the component doing the physical work every time your dishwasher empties itself between cycle stages and at the end of the wash. Rated 120V, 0.8A. Over time, the impeller can wear down, debris can jam the motor, or the motor windings themselves can fail electrically. A failing drain pump produces a very recognizable pattern: standing water left in the tub after a cycle finishes, water leaking from underneath the dishwasher, unusually loud or grinding noise during the drain phase, or a pump that audibly tries to run for a moment and then shuts off right away without actually clearing the water. It directly replaces AP4342621 and PS4222308. Quick Answer The XPARTCO DD31-00005A Dishwasher Drain Pump Motor fixes Samsung dishwashers that won't drain, leave standing water in the tub, leak underneath the unit, or run unusually noisy during the drain phase. 120V, 0.8A. Replaces AP4342621, PS4222308. This is the drain pump — not the same part as the wash/circulation pump (DD31-00004B), which handles spraying water during the wash itself rather than draining it afterward. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Water leaking from underneath the dishwasher Unusually loud, grinding, or strange noise during the drain phase Pump that tries to run briefly, then shuts off right away without draining Dishwasher running noisily overall Cycle that stalls or won't advance past the drain step Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: DD31-00005A, 1550731, DW0005A, AP4342621, ASM35435 PD00002014, PS4222308 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as: DMR57LFB, DMR57LFS, DMR57LFW DMR77LHB, DMR77LHS, DMR77LHW DMR78AHB, DMR78AHS, DMR78AHW DMT300RFB, DMT300RFS, DMT300RFW DMT400RHB, DMT400RHS, DMT400RHW DMT800RHB, DMT800RHS, DMT800RHW Note — drain pump, not wash pump: This is the drain pump, which removes wastewater from the tub. It is a different part from the DD31-00004B wash/circulation pump motor, which sprays water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Aftermarket replacement drain pump motor — removes wastewater from the tub during the drain phase Resolves "not draining," "standing water," "leaking underneath," and "noisy drain phase" symptoms caused by pump failure Impeller-driven design for efficient water removal through the drain hose Rated 120V, 0.8A Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4342621 and PS4222308 Compatible with a range of Samsung dishwasher models Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DD31-00005A OEM Part Number DD31-00005A Part Type Dishwasher Drain Pump Motor Condition Aftermarket Replacement Brand Samsung Function Removes wastewater from the tub during the drain phase Voltage 120V Amperage 0.8 A Related Part DD31-00004B wash/circulation pump (different function, sold separately) Repair Difficulty Moderate — tight working space under the unit Quantity 1 drain pump motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Remove Standing Water First Unplug the dishwasher and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Access to the drain pump is typically from underneath the unit, which can mean a tight working space — pulling the dishwasher partially out from under the counter, or working from the front after removing the lower access panel, makes this considerably easier depending on your installation. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old pump, remove its mounting screws or clips, and pull it free. Install the new DD31-00005A pump in the same position, reconnect the drain hose connections securely, and reconnect the electrical connector fully. Restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, pliers, towels or a small cup for removing standing water, work gloves. Frequently Asked Questions My dishwasher pump tries to run for a second, then shuts off. Is that the drain pump? Yes, this is a documented symptom of a failing drain pump motor — one customer described exactly this pattern, where the pump attempted to run and then shut off right away without actually clearing the standing water. This typically points to a motor that's jammed, worn, or electrically failing rather than a clog, since a simple clog usually lets the motor keep running (just ineffectively) rather than shutting off immediately. Access to my drain pump is really tight. Is that normal? Yes, this is a common challenge with under-counter dishwasher installations — the drain pump often sits low and toward the back, and reaching it can mean working in a cramped space regardless of the model. Removing standing water first and having patience with the process makes a real difference, and pulling the unit partially forward, if your installation allows it, can improve access significantly. Is this the same as the wash pump on my dishwasher? No. This DD31-00005A is specifically the drain pump, which removes wastewater from the tub. Your dishwasher's separate wash/circulation pump (DD31-00004B) is what sprays water through the spray arms during the actual wash portion of the cycle. If your dishwasher isn't cleaning dishes well but drains fine, the wash pump — not this drain pump — is more likely the issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical rating, impeller design, and mounting configuration of the original DD31-00005A drain pump motor used in compatible Samsung dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less