WD19X25278 Dishwasher Genuine OEM Diverter Assembly
Replaces Part Numbers: WD19X25278, WD18X21678, 4922277, WD00X25260, AP6871922, PS12710077.
Description: This Diverter Valve Assembly Kit serves a Genuine OEM replacement Part for specific GE dishwasher models. Its key function is to provide an alternative passage for water to reach the upper spray arms of the dishwasher. A faulty or damaged diverter valve often manifests as water leaks within the dishwasher. When such leaks occur and can be traced back to the diverter valve, this assembly kit offers a comprehensive solution. It includes all necessary components and fasteners to efficiently replace the valve. This kit is suitable for use with specific General Electric dishwasher models.
W10518394 Genuine OEM Whirlpool Dishwasher Heating Element
The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades.
This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed.
Common Problems This Part Fixes
Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase
Wash water not getting hot enough — poor cleaning performance even with proper detergent
Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation
Heated dry cycle not working — no warm air at the end of the cycle
Element visibly burned through, broken, or showing arcing damage
Multimeter continuity test on the element shows an open circuit (no continuity)
Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element)
Detergent not fully dissolving — water too cool to activate the formulation
Replaces Part Numbers
This dishwasher heating element directly replaces the following OEM and cross-reference part numbers:
W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead.
Compatibility
This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including:
Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models
Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram)
Maytag dishwashers — select models (verify with parts diagram)
KitchenAid dishwashers — select models
Amana dishwashers — ADB1400AGW and related models
Kenmore / Sears dishwashers — select Whirlpool-built models
Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase
Rated 1200W for efficient heating and reliable temperature control
Oval-shape element approximately 15" L x 3" W x 3" H
Mounts in the bottom of the dishwasher tub, secured underneath with large nuts
Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement
Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times)
Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070
Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
W10518394
Part Type
Dishwasher Heating Element
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Shape
Oval (NOT interchangeable with horseshoe-style elements)
Wattage
1200W
Dimensions
Approximately 15" L x 3" W x 3" H
Mounting Location
Bottom of dishwasher tub
Related Parts (Sold Separately)
Rubber Washer (717273), Heater Nut (8268548)
Post-Install Step
Diagnostic reset required on most Whirlpool dishwashers
Compatible Brands
Whirlpool, Maytag, KitchenAid, Amana, Kenmore
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses.
Frequently Asked Questions
Why are my dishes coming out wet — is the heating element the cause?
Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed.
After installing the new element, the dishwasher still isn't heating — why?
On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well.
How is the W10518394 different from horseshoe-shape heating elements?
The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher.
Do I need to replace the rubber washers and nuts when installing this?
Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WPW10455261 Dishwasher Genuine OEM Pump and Motor Assembly
Fits specific Whirlpool, Maytag, Kenmore Dishwasher models
Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it.
Replaces Part Numbers: WPW10455261, W10455261, 2312159, W10500284, AP6021679, PS11755005.
California Residents only
WARNING: California’s Proposition 65
WD26X10025 Dishwasher Genuine OEM Drain Pump
Fits Specific GE Dishwasher Models.
Replaces Part Numbers: WD26X10025, 1168314, AH1021347, EA1021347, OEM15537486, AP3884371, PS1021347.
Description: This Drain Pump Assembly is an OEM part for GE dishwashers. This component is responsible for removing water from the dishwasher during the drain cycle, ensuring that your dishes are cleaned and rinsed effectively. The pump works by expelling the used water through the drain hose and into the household plumbing.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit
The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet.
This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours.
Quick Answer
The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258.
Common Problems This Part Fixes
Dishes not getting clean — food soil, grit, or film left behind after a full cycle
Top rack not getting wet or not getting cleaned while the bottom rack washes normally
Spray arms turning slowly or not turning at all — insufficient water pressure
Loud humming, whining, or grinding noise during the wash portion of the cycle
Dishwasher runs a full cycle quietly with no audible water circulation
Water pooling in the base pan under the dishwasher from a leaking pump shaft seal
Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle
Cleaning performance that has gradually declined over months as bearings wear
Pump motor humming but the impeller not turning — seized shaft or jammed impeller
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers:
WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands:
GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series)
Café dishwashers (CDT865 and CDT866 series)
Monogram dishwashers (ZDT915 and ZDT975 series)
Hotpoint dishwashers (select GE-built models)
Haier dishwashers (select GE-platform models)
Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS.
Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile
Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed
Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump
Drives water through the lower spray arm, middle spray arm, and upper wash manifold
Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure
Sealed shaft design protects the motor from sump water intrusion
Direct drop-in replacement for the superseded WD26X22789 — no modifications required
Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms
Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WD26X25103
Part Type
Dishwasher Variable Wash Pump Kit (Circulation Pump)
Condition
Genuine OEM
Brand
GE Appliances
Motor Type
Variable speed
Voltage
120V / 60 Hz
Function
Circulates water under pressure to the spray arms and upper wash manifold
Kit Contents
Wash pump assembly + integrated wiring harness
Location
Underneath the tub, mounted to the sump housing
Connections
2 hose clamps + 2 electrical connections
Supersedes
WD26X22789
Repair Difficulty
Moderate — 1 to 2 hours
Quantity
1 pump kit
Compatible Brands
GE, GE Profile, Café, Monogram, Hotpoint, Haier
Installation Notes
⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves.
Frequently Asked Questions
My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump?
It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced.
What does "variable" mean on this pump, and does it matter?
It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly.
The dishwasher is making a loud grinding noise. Do I need the whole pump?
Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak.
I found water in the pan underneath the dishwasher. Could the pump cause that?
Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear.
Does this kit include everything, or do I need to reuse parts from the old pump?
The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks."
What's the difference between WD26X25103 and WD26X22789?
They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11665769 Dishwasher Sump Pump and Motor
Pump and Motor Assembly
Replaces Part Numbers: W11665769, W11085683, W10917110, W11164469, AP7212556, PS16875975.
Description: This dishwasher pump and motor assembly is compatible with specific Whirlpool, Maytag, Kenmore dishwasher models. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.
5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm
The 5304517203 is a genuine Frigidaire OEM lower spray arm for Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers. Positioned at the bottom of the dishwasher tub, this arm rotates as water is pumped through it, spraying water in all directions through its nozzle openings to clean dishes in the lower rack. It snaps directly into the bottom sump assembly and is essential for proper water distribution during the wash cycle.
Made of durable plastic and metal, finished in gray/blue. Over time, the arm can crack, warp, or wear from general use and repeated exposure to hot water and detergent — high heat exposure in particular is a documented cause of failure. A broken or worn spray arm typically shows up as visible damage on the arm itself, dishes in the lower rack not getting cleaned properly, reduced or uneven water coverage, or the arm having difficulty rotating or getting stuck. It directly replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623
Quick Answer
The 5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm fixes Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers where the lower rack isn't getting cleaned properly, water coverage is reduced or uneven, or the arm won't rotate freely or has visible cracks. Snaps into the bottom sump assembly. Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623. After installing, confirm the arm spins freely by hand and doesn't contact the heating element before running a cycle.
Common Problems This Part Fixes
Dishes in the lower rack not getting cleaned properly
Reduced or uneven water coverage during the wash cycle
Spray arm that won't rotate freely or gets stuck
Visible cracks, warping, or damage on the arm itself
Arm that has come loose or detached from the sump assembly
Clogged nozzle holes reducing water pressure and spray coverage
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher lower spray arm directly replaces the following OEM and cross-reference part numbers:
5304517203, 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This lower spray arm is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers built on the same platform.
Note: Non-genuine versions of this exact part number are sold by several third-party sellers. A customer using a non-genuine version of this spray arm reported it came loose and broke during operation, so confirm you're ordering the genuine Frigidaire part rather than a lower-cost imitation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Frigidaire OEM part — factory-specified nozzle pattern and rotation fit
Snaps directly into the bottom sump assembly for a secure, no-tools installation
Resolves "not cleaning lower rack dishes," "uneven water coverage," and "won't rotate freely" symptoms
Durable plastic and metal construction, gray/blue finish
Approximate dimensions: 16.00" x 3.10" x 3.10" (L x W x H)
Direct drop-in replacement — no modification required
Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623
Compatible with Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
5304517203
Part Type
Dishwasher Lower Spray Arm
Condition
Genuine OEM
Brand
Frigidaire
Location
Bottom of the dishwasher tub, in the lower sump assembly
Material
Plastic and metal
Color
Gray / Blue
Dimensions
Approx. 16.00" x 3.10" x 3.10" (L x W x H)
Repair Difficulty
Very Easy — no tools required
Quantity
1 lower spray arm
Compatible Brands
Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, Kenmore
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Confirm Clearance From The Heating Element Disconnect power to the dishwasher and shut off the water supply before beginning. Wear work gloves. Open the dishwasher and pull out the lower rack, setting it aside. Remove the old lower spray arm by releasing the locking tabs on each side and gently pulling it off the sump assembly. Snap the new 5304517203 spray arm onto the sump assembly in the same position. Before closing everything up, spin the arm gently by hand to confirm it rotates freely and does not make contact with the heating element — a real customer account described a spray arm and its support becoming loose and falling into the tub during use, so it's worth double-checking that the arm is fully and securely seated before running a cycle. Return the lower dish rack to its position and close the dishwasher door. Restore power and water, then run a test cycle to confirm the arm spins smoothly and dishes in the lower rack are getting properly cleaned. Tools needed: none.
Frequently Asked Questions
My dishes in the lower rack aren't getting clean. Is this the part I need?
Yes, this is one of the most common symptoms of a worn or damaged lower spray arm. If the arm is cracked, clogged, or not rotating freely, water can't reach dishes in the lower rack evenly, leaving them dirty even when the upper rack comes out clean.
I've read that a spray arm can come loose during operation. How do I prevent that?
This has been reported, particularly with non-genuine imitation parts under the same number. To help prevent it, make sure the new arm snaps fully and securely onto the sump assembly during installation, and spin it gently by hand to confirm it's seated correctly and rotates without wobbling before running your first cycle with it installed.
Do I need any tools to replace this spray arm?
No. This is a simple snap-in, snap-out repair — release the locking tabs on the old arm to remove it, and press the new one onto the sump assembly until it clicks into place. No tools are required.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original nozzle pattern, dimensions, and sump connection of the lower spray arm originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor
The WPW10348269 is a genuine Whirlpool OEM drain pump motor for Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers. This pump uses an electric motor to create suction, pulling wastewater out of the tub and expelling it through the drain hose at the end of each cycle. This is the dedicated drain pump, distinct from a circulation pump — such as our WPW10605057 listing — which handles spraying water through the spray arms during the wash itself rather than draining it afterward.
Rated 120VAC, 60Hz, 45W, 0.7A, with a run time pattern of 5 minutes on, 30 minutes off. Ships as a complete pump motor with impeller and O-ring. If the impeller becomes damaged or the motor shorts out and stops draining, the pump body itself can crack over time, leading to leakage — replacing the pump before that happens is the more reliable fix. Symptoms of a failing drain pump include water not draining from the tub, unusual noise such as grinding during the drain phase, or visible leaks from underneath the unit. It directly replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379
Quick Answer
The WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor fixes Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers that aren't draining, are making grinding noise during the drain phase, or are leaking from underneath. 120VAC, 60Hz, 45W, 0.7A. Includes impeller and O-ring. Replaces W10348269, WPW10348269VP, W10084573, W10158351, 661662, 8558995, 8565839, 2813258, AP6020066, EAP11753379, PD00004898, PS11753379. This is the drain pump — a separate part from our WPW10605057 circulation pump listing, which handles spraying water rather than draining it.
Common Problems This Part Fixes
Dishwasher not draining — standing water left in the tub after a cycle
Grinding noise coming from the drain pump area
Water leaking from underneath the dishwasher
Cycle stalling or failing to advance past the drain step
Dishes not getting cleaned as a downstream effect of drainage problems
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
WPW10348269, W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Whirlpool dishwashers, and also fits select KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers built on the Whirlpool platform.
Note — drain pump, not circulation pump: This is the dedicated drain pump, which removes wastewater from the tub. It is a separate part from our WPW10605057 listing, which is the circulation pump and diverter motor responsible for spraying water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs.
Key Features
Genuine Whirlpool OEM part — factory-specified motor and impeller design
Pumps wastewater out of the tub through the drain hose
Resolves "not draining," "grinding noise," and "leaking underneath" symptoms caused by pump failure
Complete assembly — includes pump motor, impeller, and O-ring
Rated 120VAC, 60Hz, 45W, 0.7A
Run time: 5 minutes on, 30 minutes off
Dimensions: approximately 3-1/2"L x 3"W x 3-1/2"H
Direct drop-in replacement — matches the original mounting and hose connections
Replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WPW10348269
Part Type
Dishwasher Drain Pump Motor (with Impeller and O-Ring)
Condition
Genuine OEM
Brand
Whirlpool
Function
Pumps wastewater out of the tub through the drain hose
Voltage
120VAC
Frequency
60 Hz
Wattage
45 W
Amperage
0.7 A
Run Time
5 min ON / 30 min OFF
Dimensions
Approx. 3-1/2"L x 3"W x 3-1/2"H
Color
White / Gray / Black / Yellow
Related Part
WPW10605057 circulation pump & diverter motor (different function, sold separately)
Repair Difficulty
Beginner to Moderate
Quantity
1 drain pump motor
Compatible Brands
Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, Roper
Installation Notes
⚠️ Unplug Dishwasher Before Starting — Removing The Unit Makes Access Easier Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This repair can be done without pulling the dishwasher out from under the counter, but many technicians find it considerably easier to access the pump if you do pull the unit out first. Remove the lower rack and any components blocking access to the tub floor, then work from underneath the dishwasher to reach the drain pump. Test the old pump for continuity with a multimeter before removing it — if it shows no continuity, or if it's getting power but still won't run, that confirms the pump has failed. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connection from the old pump, remove its mounting hardware, and pull it free. Install the new WPW10348269 in the same position, reconnect the drain hose connection securely, and reconnect the electrical connector fully. Reinstall any components removed for access and the lower rack. Restore power, run a test cycle, and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, 5/16" nut driver, 5/8" wrench, flathead screwdriver, multimeter, work gloves.
Frequently Asked Questions
Do I need to pull the dishwasher out from under the counter for this repair?
Not strictly — this pump can be replaced without fully removing the dishwasher. That said, several customers who've done this repair note that pulling the unit out first makes access considerably easier, since you're working from underneath the appliance either way. If you have the space to pull it out, it's worth doing to make the job smoother.
How do I know if the pump has actually failed?
Test the pump motor with a multimeter set to continuity before replacing it. If there's no continuity, or if the pump is receiving power but still won't run, that confirms the motor has failed and the pump should be replaced. This quick check avoids replacing a part that isn't actually the problem.
My old pump was leaking. Why does that happen?
If the impeller becomes damaged or the motor shorts out and stops running, the pump body itself can develop a crack over time, which leads to leakage. Rather than trying to repair a leaking pump, replacing the complete assembly resolves both the drainage failure and the leak at the same time.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original motor, impeller, and hose connection configuration of the drain pump originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11612327 Dishwasher Genuine Circulation Pump
Circulation pump and motor assembly
Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935.
Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.
WD24X10018 Dishwasher Genuine Piston & Nut Assembly
Replaces Part Numbers: WD24X10018, 821081, WD22X0133, WD22X133, WD24X0199, WD24X0220, WD24X199, WD24X220, AH260690, EA260690, AP2617344, PS260690.
Description: This Piston & Nut Assembly is a Genuine parts for specific GE dishwasher models. It plays a critical role in the dishwasher’s water management system, helping to control water flow and ensuring proper drainage during the wash cycle. You should replace this piston & nut assembly if it becomes worn out or damaged. Common causes of a bad piston & nut assembly can include mineral buildup from hard water, general wear and tear from regular use, or physical damage due to debris or foreign objects in the dishwasher.
8269144A Dishwasher Genuine Drain Hose Extension
Replaces Part Number: 8269144A, 1489097, 8269144, AH2358130, EA2358130, AP4399659, PS2358130.
Description: This Drain Hose is a Genuine OEM part for select Whirlpool dishwasher models. This flexible hose is designed to carry waste water from the dishwasher to the kitchen drain system or garbage disposal, ensuring that the dishwasher drains properly after each wash cycle. Common causes of damage to the Drain Hose often involve regular wear and tear, bending or kinking of the hose during installation or maintenance activities, or deterioration over time due to exposure to hot water and detergents.
