XPARTCO 17438200000160 Gas Dryer Flame Switch
The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet.
When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers.
Common Problems This Part Fixes
Gas dryer not heating — flame switch not confirming flame presence to the control board
Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal
No-heat fault code displayed on models with digital control panels
Dryer runs and tumbles normally but produces no heat
Burner repeatedly cycling on and off rapidly during a heat cycle
Visible damage, corrosion, or carbon buildup on the flame switch near the burner
Replaces Part Numbers
This flame switch directly replaces the following part number:
17438200000160, AP7153000, PS18188577.
This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This flame switch is compatible with select Midea, Insignia gas dryers, including:
Midea MLG45N1BWW gas dryer
Midea MLG45N3BMG gas dryer
Midea MLG45N3BWW gas dryer
Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load)
Midea CDG41N1AW gas dryer (Criterion, air vent)
Midea CDG45N1AW gas dryer (Criterion, air vent)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Confirms flame presence at the burner after ignition and signals the control board accordingly
Safety component — helps ensure the gas valve closes promptly if a flame is not detected
Mounts directly to the burner assembly in the same position as the original switch
Genuine Midea manufacturer part number — designed as a direct fit for compatible models
Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers
Installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
XP17438200000160
Part Type
Gas Dryer Flame Switch
Condition
Aftermarket Replacement
Application
Gas Dryers (Midea platform)
Location
Mounted on the burner assembly
Compatible Brands
Midea
Installation Notes
⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician.
⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
What does the flame switch do, and how is it different from an igniter?
The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring.
My burner lights and then shuts off after a few seconds — is this the flame switch?
Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement.
Why is this called a "flame switch" rather than a "flame sensor"?
Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept.
Why does this repair require opening the whole dryer cabinet?
On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM WH22X38697 Washer Main Control Board
The Genuine OEM GE WH22X38697 is the main control board for select GE front-load washers. The main control board is the electronic control for the washer, so it is replaced when it has been diagnosed as the cause of a washer fault.
This is the original GE part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering, because GE uses many similar control boards with different part numbers.
Quick Answer
The Genuine OEM WH22X38697 Main Control Board replaces the main control board on a compatible GE front-load washer when it has failed. Replaces WH22X29546, WH22X30897, WH22X32058, WH22X32458, WH22X34357, WH22X34660, WH22X35518, WH22X36638 and WH22X37837. Confirm the board is the cause before replacing it.
When To Replace This Part
The main control board has been diagnosed as faulty
Your old board carries one of the superseded numbers listed below
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This main control board replaces or supersedes the following part numbers:
WH22X38697, WH22X37837, WH22X36638, WH22X32458, WH22X35518, WH22X30897, WH22X29546, WH22X32058, WH22X34660, WH22X36858, WH22X37838, AGE26929, AP8054699, OEM24164106, PD00093156, PS17874598
If your old board shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This main control board is listed for select GE front-load washers. Retailers do not publish a model list for this part, so please verify your model before ordering.
Note: GE sells many similar-looking washer control boards under different part numbers, and not all are interchangeable. Send us your full model number, or check it against your parts diagram, and we'll verify fit before you order.
Key Features
Genuine OEM GE part, not an aftermarket equivalent
Main control board for select GE front-load washers
Replaces nine earlier GE control board part numbers
Sold individually
Product Specifications
Part Number
WH22X38697
OEM Part Number
WH22X38697
Part Type
Washer Main Control Board
Condition
Genuine OEM
Manufacturer
GE
Quantity
1 Board
Application
Select GE Front-Load Washers
Installation Notes
⚠️ Disconnect Power And Water Before Installing Unplug the washer and turn off the water supply before you begin. Control boards are sensitive to static, so touch bare metal on the washer frame before handling the board. Photograph or label each wire connector, disconnect them, and remove the old board. Fit the new board, reconnect every connector to its original position, restore power and water, and run a test cycle.
Frequently Asked Questions
How do I know the control board is the problem?
Control boards share symptoms with other parts, such as switches, sensors, wiring and motors. Check those and your model's service guide first, and confirm the board is at fault before replacing it.
Is this an OEM or aftermarket part?
This is a genuine OEM part from GE, not an aftermarket equivalent.
Does this replace my old board number?
It replaces WH22X29546, WH22X30897, WH22X32058, WH22X32458, WH22X34357, WH22X34660, WH22X35518, WH22X36638 and WH22X37837. If your board shows another number, contact our support team and we'll check it.
Will this fit my washer?
It is listed for select GE front-load washers, but no model list is published for this part. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly
The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase.
When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models.
Quick Answer
The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series.
Common Problems This Part Fixes
Error code H2O displayed — dishwasher not receiving enough water or no water at all
Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained
Dishwasher not filling with water when a cycle is started
Dishwasher overfilling — sensor not signaling the control board to stop filling
Dishwasher stopping mid-cycle without completing the wash
Excessive noise during operation — sensor not accurately controlling spray arm water pressure
Dishwasher requires priming with water to start (filling the tub manually before it will run)
Replaces Part Numbers
This pressure sensor directly replaces the following OEM and cross-reference part numbers:
WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines:
GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series
GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series
GE dishwashers — GDP615, GDP645, GDP665 series
GE Profile dishwashers — PDT715, PDT775, PDT785 series
GE Café dishwashers — CDT800, CDT875 series
GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series
Hotpoint dishwashers — HDF310, HDF330 series
Haier dishwashers (select GE-platform models)
GE / Café / Profile — QDP555 series
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage
Resolves H2O and FTD error codes on compatible GE dishwashers
Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement
Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001
Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series
Sold individually
Quick DIY repair — installs in 15–20 minutes with a screwdriver
Product Specifications
Part Number
WD21X25468
Part Type
Dishwasher Pressure Sensor Assembly (Pressure Switch)
Condition
Genuine OEM
Application
GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers
Function
Monitors tub water level and pressure — signals control board for fill and drain control
Error Codes Resolved
H2O (no/low water), FTD (Failure to Drain)
Sold As
Single sensor assembly
Compatible Brands
GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver.
Frequently Asked Questions
What does the dishwasher pressure sensor do?
The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles.
What do error codes H2O and FTD mean on GE dishwashers?
H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes.
Should I try cleaning the sensor before replacing it?
Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468.
My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor?
Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH42X10650 Washer Control Panel, White
Replaces Part Numbers: WH42X10650, AP3995175, 1264621, AH1482468, EA1482468, PS1482468.
The WH42X10650 is a genuine GE replacement part, specifically designed as a control panel for GE washing machines. It houses and operates the control buttons and display, ensuring compatibility and reliability for your appliance.
17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor)
The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time.
When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools.
Quick Answer
The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models.
Common Problems This Part Fixes
Dryer overheating — thermistor not accurately reporting rising temperature to the control board
Dryer not heating at all — thermistor circuit open or shorted
Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle
Dryer taking much longer than normal to complete a cycle
Not-heating fault code displayed on models with digital control panels
Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading
Dryer cycling heat on and off erratically
Replaces Part Numbers
This temperature sensor directly replaces the following OEM and cross-reference part numbers:
17438200000404, WF-123X2060, AP7157538, PS18188581
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including:
Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW
Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW
Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13
Criterion — CDE41N1AW (electric), CDG41N1AW (gas)
Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1
Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring
Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating
Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly
Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models
Replaces WF-123X2060
Installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
17438200000404
Part Type
Dryer Temperature Sensor (NTC Thermistor)
Condition
Genuine OEM
Application
Electric and Gas Dryers (Midea platform)
Sensor Type
NTC (Negative Temperature Coefficient)
Resistance at Room Temp
Approximately 10,000 – 12,000 ohms (~70°F)
Location
Blower housing/exhaust duct or drum cavity, depending on model
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing).
Frequently Asked Questions
How do I test if the temperature sensor (thermistor) has failed?
Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine.
My Midea dryer has more than one temperature sensor — how do I know which one to replace?
Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor.
What is the difference between 17438200000404 and WF-123X2060?
These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part.
Does this sensor fit my Insignia or Criterion dryer?
Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit
The AGM30045804 is a genuine LG OEM high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does.
Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335.
Quick Answer
The AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step.
What's In The Kit
Component
Function
High-Limit Thermostat
Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools.
Thermistor (with wire harness)
Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle.
Common Problems This Kit Fixes
Dryer overheating, sometimes scorching or damaging clothing
Dryer running with little or no heat
Inconsistent drying times — cycle shuts off too early or runs longer than necessary
Temperature-related error code displayed on the control panel
Clothes remaining damp after a full drying cycle
High-limit thermostat that keeps tripping repeatedly
Dryer that has already had its high-limit thermostat replaced once but the problem returned
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers:
AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform.
Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order.
Key Features
Genuine LG OEM part — factory-specified resistance values and switch thresholds
Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit
Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms
Thermistor ships with its wire harness included
High-limit thermostat resets automatically after tripping — no replacement needed after each trip
Direct drop-in replacement for both original components
Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335
Compatible with LG and select Kenmore and GE-branded LG-built dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
AGM30045804
Part Type
Dryer High-Limit Thermostat and Thermistor Kit
Condition
Genuine OEM
Brand
LG
Kit Contents
High-limit thermostat + thermistor with wire harness
Thermistor Location
Blower housing
High-Limit Thermostat Type
Automatically resetting
Repair Difficulty
Easy to Moderate — 30 to 60 minutes
Compatible Brands
LG, select Kenmore, GE (LG-built models)
Installation Notes
⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead?
This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit.
What's the difference between the thermistor and the high-limit thermostat?
The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating.
My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing?
Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same resistance values, switch threshold, and wire harness configuration as the high-limit thermostat and thermistor originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO EBF61315802 Washer Door Lock Switch
The XPARTCO EBF61315802 is an aftermarket replacement washer door lock switch assembly compatible with a wide range of LG front-load washers and Kenmore 796-series front-load washing machines. The door lock switch is mounted on the front panel just inside the door opening — when the door is closed, the door's striker engages the lock and the switch reports back to the control board that the door is securely closed. The lock then engages electromagnetically to physically prevent the door from being opened during the wash and spin cycles, eliminating the risk of water leaks and protecting the user from the high-speed spinning drum.
When this part fails, the washer will not start (since the control board can't confirm the door is locked), will stop mid-cycle, may display DE1 or DE2 error codes, may not actually lock the door (allowing it to open during a cycle), or may leak water around the door. Rated 125V AC, 60Hz, with a 3-pin connector. It directly replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, and PD00008063. Often replaced alongside the door lock strike (MFG63099101, sold separately), which is the matching component on the door itself. Installs in 15–20 minutes with basic hand tools — no full front panel removal needed on most models.
Quick Answer
The XPARTCO EBF61315802 Washer Door Lock Switch fixes LG and Kenmore 796-series front-load washers that won't start, won't lock the door, stop mid-cycle, display DE1 or DE2 error codes, allow the door to open during a cycle, or leak water around the door. 125V AC, 60Hz, 3-pin connector. Replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, PD00008063. Often paired with the door lock strike (MFG63099101, sold separately).
Common Problems This Part Fixes
Washer won't start — control board not detecting a locked door
Door fails to lock at the start of the cycle
DE1 or DE2 error codes displayed on the control panel
Washer stops mid-cycle due to a door lock fault
Door pops open or unlatches during the wash or spin cycle (safety concern)
Water leaking around the door during operation — door not sealing because the lock isn't fully engaging
Stuck, aged, worn, or broken door lock
Door open/close action no longer smooth — lock binding
Repeated mid-cycle shutdowns or interruptions
Replaces Part Numbers
This door lock switch directly replaces the following OEM and cross-reference part numbers:
EBF61315802, EBF62534401, AP6992889, PS16223547, ALG54705, AP5672154, PD00008063, PS7792232, B088MG37Y9
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door lock switch is compatible with select LG and Kenmore 796-series front-load washers, including:
LG front-load washers — WM1388HW, WM1455HWA series
LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3180CW series
LG front-load washers — WM3250HRA, WM3250HVA, WM3250HWA, WM3270CW series
LG front-load washers — WM3370HRA, WM3370HVA, WM3370HWA, WM3400CW, WM3460CV, WM3488HS, WM3488HW, WM3499HVA, WM3500CW, WM3555HWA series
LG front-load washers — WM3570HVA, WM3570HWA, WM3600HVA, WM3670HVA, WM3670HWA, WM3700HVA, WM3700HWA series
LG front-load washers — WM3770HVA, WM3770HWA, WM3900HBA, WM3900HWA, WM3997HWA, WM3998HBA series
LG front-load washers — WM4070HVA, WM4070HWA, WM4200HBA, WM4200HWA, WM4270HVA, WM4270HWA, WM4370HKA, WM4370HWA, WM4500HBA series
LG front-load washers — WM5000HVA, WM5000HWA, WM8000HVA, WM8000HWA, WM8100HVA, WM8100HWA, WM8500HVA series
LG front-load washers — WM9000HVA, WM9000HWA, WM9500HKA series
LG WashTower units — WKE100HVA, WKE100HWA, WKEX200HBA, WKEX200HWA, WKG101HVA, WKG101HWA, WKGX201HBA series
LG Studio models — GCWP1069CD/CD1/CD2/CD3, GCWW1069CD7, GCWW1069CS7 series
Kenmore / Sears front-load washers — 796-series (79641002610, 79641072310, 79641073310, 79641182310, 79641183310, 79641262610, 79641282310, 79641283310, 79641302610, 79641303610, 79641382410, 79641383410, 79641392610, 79641482410, 79641572210, 79641573210, 79641582410, 79641962610, 79641963610, 79641982410, and many related models)
Note: The door lock switch (EBF61315802) and the door lock strike (MFG63099101) are two separate components that work together — if both have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new switch. Always verify your model number before ordering.
Key Features
Door lock switch assembly — detects when the door is closed and electromagnetically locks it during wash and spin cycles
Resolves DE1 and DE2 error codes caused by door lock failure on compatible LG and Kenmore washers
Prevents water leaks and protects the user by ensuring the door cannot open during operation
125V AC, 60Hz — correct electrical specifications for compatible LG and Kenmore washers
3-pin connector for secure wire harness fit
Replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, and PD00008063
Compatible with LG WM1388, WM3050, WM3170, WM3250, WM3370, WM3500, WM3570, WM3670, WM3770, WM3900, WM3997, WM4070, WM4270, WM4370, WM5000, WM8000, WM8100, WM8500, WM9000, WM9500 series and Kenmore 796-series front-load washers
Compatible with LG WashTower (WKEX, WKE, WKG, WKGX) units
Often replaced together with the door lock strike (MFG63099101, sold separately)
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–20 minutes with basic hand tools (no full front panel removal needed on most models)
Product Specifications
Part Number
EBF61315802
Part Type
Washer Door Lock Switch Assembly
Condition
Aftermarket Replacement
Application
Front-Load Washers (LG / Kenmore Samsung-built platform)
Voltage
125V AC
Frequency
60 Hz
Connector
3-pin connector
Lock Type
Electromagnetic
Error Codes Resolved
DE1, DE2 (door lock errors)
Often Paired With
Door Lock Strike (MFG63099101, sold separately)
Compatible Brands
LG, Kenmore (LG-built)
Installation Notes
⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. On most LG and Kenmore front-load models, you can replace the door lock switch without removing the whole front panel — a much faster repair than expected. Open the washer door (if the door is stuck locked, use a putty knife to pry the white latch on the door lock assembly through the bottom service opening, then open the door). Remove the spring-loaded wire clamp securing the door boot to the front panel — needle-nose pliers help here. Peel back the rubber door boot from the front panel to expose the rear of the door lock switch. Remove the 2 Phillips screws holding the switch to the front panel. Reach in and pull the switch out through the boot opening. Disconnect the wire harness from the old switch. Connect the wire harness to the new EBF61315802, position it in place, and secure with the 2 mounting screws. Press the rubber door boot back fully into the groove at the front panel — this is the trickiest part of the install (an extra pair of hands helps). Reinstall the spring-loaded wire clamp around the boot to secure it. Restore power and test by closing the door and starting a cycle. Tools needed: Phillips screwdriver, needle-nose pliers, putty knife (for stuck doors), work gloves.
Frequently Asked Questions
What do error codes DE1 and DE2 mean on LG washers?
DE (Door Error) codes on LG front-load washers indicate the control board cannot confirm the door is properly closed and locked. DE1 typically appears when the door switch reports the door as open at the start of a cycle, and DE2 typically appears when the door signal is lost during a cycle. Both can be caused by a failed door lock switch, a worn or broken door lock strike (MFG63099101) on the door itself, or a damaged wiring harness. Replacing the EBF61315802 door lock switch resolves these codes when the switch is the cause; if the codes return after replacement, the strike on the door or the harness should be inspected next.
Do I need to replace the door lock strike (MFG63099101) too?
Not always, but often. The door lock strike is the matching component mounted on the door itself — it's the part that the switch's electromagnetic lock grips when the door closes. If the strike is worn, cracked, or its plastic teeth are broken, the new switch won't lock reliably even if it's working perfectly. Inspect the strike on the door for visible damage before replacing just the switch. Many repair scenarios call for replacing both at the same time, since both wear together and the parts complement each other.
My washer door is stuck closed — how do I get it open to install this?
If the door is stuck in the locked position because the existing switch has failed, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the installation. Always disconnect power from the washer before attempting this.
Do I really not need to remove the front panel?
Correct — on most LG and Kenmore front-load models, you can replace the door lock switch by working through the door opening after pulling back the rubber door boot. This avoids the much more involved process of removing the entire front panel. The trickiest part of the repair is pressing the rubber door boot back into its groove on the front panel after the switch is installed — an extra pair of hands is helpful for this step. The whole repair typically takes 15–20 minutes.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the electrical specifications (125V AC, 60Hz), 3-pin connector configuration, electromagnetic lock function, and dimensions of the original EBF61315802 door lock switch used in compatible LG and Kenmore 796-series front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WH13X26535 Genuine OEM GE Washer Water Valve
The WH13X26535 is a genuine GE OEM water inlet valve assembly for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This valve controls the flow of hot and cold water into the tub during the fill portion of the cycle, ensuring each wash uses the correct amount of water at the right temperature blend. It's housed in durable gray plastic.
Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use — five years is a commonly cited service life before this valve starts to show problems. A failing valve produces a clear set of symptoms: the washer not filling properly, water continuing to fill or drip even when the washer is turned off, or leaking near the valve area. It directly replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736. As a genuine OEM part, the WH13X26535 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The WH13X26535 Genuine OEM GE Washer Water Valve fixes GE top-load washers that aren't filling properly, are overfilling, or have water slowly dripping into the tub even when the washer is off. Housed in gray plastic. Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, PD00052736. This replacement valve does not include a thermistor or gasket — if your old valve has a thermistor mounted in front of the solenoids, you'll need to transfer it (with its gasket) to the new valve. Also not the same as the similarly-numbered WH13X26534, which is a separate valve for other GE/Hotpoint models.
Common Problems This Part Fixes
Washer not filling with water properly
Washer overfilling
Water slowly dripping or leaking into the tub even when the washer is turned off
Leaking near the valve connections
No hot water reaching the tub, or no cold water reaching the tub
Cycle stalling at the fill step and never advancing to wash
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
WH13X26535, WH13X24386, WH13X24392, 4931303, 003C17, AGE26261, AP6892695, 4476388, 4931303, OEM20678094, EAP11729481, EAP12726769, K-78637-2, PD00052736, PS12726769.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, spanning model series GTW460, GTW465, GTW485, GTW490, GTW500, GTW525, GTW540, and VTW540, including specific model numbers such as 5TW4207ST0WS, 5TW4307SW0WS, ETW485ASW0WB, GTW460AMJ0WW, GTW460AMJ1WW, and GTW460AMJ2WW.
Note — thermistor transfer required, and not the same as WH13X26534: This valve does not include a thermistor or the rubber gasket that seats it. If your original valve has a thermistor mounted in front of the solenoids, you must transfer that thermistor and its gasket onto this new valve during installation. Separately, this part is not the same as the similarly-numbered WH13X26534, a distinct valve used on other GE/Hotpoint models with its own cross-reference set (PS12726768, AP6891106). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified solenoid design and housing
Controls hot and cold water flow into the tub
Resolves "won't fill properly," "overfilling," and "dripping into the tub when off" symptoms caused by valve failure
Durable gray plastic housing
Direct drop-in replacement — matches the original mounting and hose connections
Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736
Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair, typically 30 to 60 minutes
Product Specifications
Part Number
WH13X26535
Part Type
Washer Water Inlet Valve
Condition
Genuine OEM
Application
Top-Load Washers
Housing Material
Gray plastic
Includes Thermistor/Gasket
No — transfer from old valve if equipped
Repair Difficulty
Moderate — 30 to 60 minutes
Quantity
1 valve
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Watch For The Thermistor O-Ring Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access is typically behind the front control panel or top of the cabinet, depending on your model. The valve assembly is usually held in place with a metal plate and two screws. Photograph the wiring and hose connections before disconnecting anything. If your old valve has a thermistor (temperature sensor) mounted in front of the solenoids, it fits into a small hole in the bracket and uses an O-ring seal that's known to degrade and leak over time — this new valve does not include one, so you'll need to carefully transfer the thermistor and its gasket from the old valve to the new one. Disconnect the electrical connector and outlet hoses from the old valve, remove its mounting screws, and pull it free. Transfer the thermistor and gasket to the new WH13X26535 if applicable, then install it in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
Does this valve come with the thermistor?
No. This valve no longer comes with the rubber gasket or thermistor that some GE washers use, mounted directly in front of the solenoids. If your old unit has one, you'll need to remove it from the old valve, along with its gasket, and transfer it onto this new valve during installation.
Water has been slowly leaking into my tub even when the washer is off. Is that this valve?
Yes, this is a documented cause. One customer traced over a year of slow leaking directly to this valve's thermistor O-ring, which is known to degrade over time and let water seep through even when the washer isn't running. Replacing the valve (and transferring a good thermistor and gasket if your model uses one) resolves this type of slow leak.
Is this the same as WH13X26534?
No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, housing, and connection type of the water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4)
The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine.
Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required.
Quick Answer
The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841.
Common Problems This Kit Fixes
Washer vibrating violently or shaking excessively during the spin cycle
Loud banging or thumping — tub striking the cabinet walls during spin
Washer "walking" or moving across the floor during high-speed spin
Error code dc displayed — Samsung out-of-balance error during spin
Error code UE displayed — unbalanced load error the washer cannot self-correct
Washer repeatedly stopping and rebalancing the load without completing the spin cycle
Visible broken, detached, or sagging suspension rod inside the washer cabinet
Rattling or clunking during agitation — tub no longer centered
Replaces Part Numbers
This suspension rod kit directly replaces the following OEM and cross-reference part numbers:
DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This suspension rod kit is compatible with select top-load washers from the following Samsung series:
Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models
Samsung WA41 series — WA41A3000AW and related models
Samsung WA42 series — WA422PRHDWR and related models
Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models
Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models
Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models
Kenmore / Sears top-load washers (select Samsung-built models)
Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet.
Key Features
Set of 4 suspension rods — complete replacement covering all four tub mounting points
Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact
Resolves Samsung error codes dc (out of balance) and UE (unbalanced load)
Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches
Spring steel construction with plastic end caps — durable and corrosion resistant
Rods are pre-coated with grease — wear work gloves during installation
Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support
No special tools required — installs in 20–30 minutes
Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
DC97-16350U
Part Type
Washer Suspension Rod and Spring Assembly
Condition
Aftermarket Replacement
Application
Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series
Quantity
Set of 4 (replace all four rods at the same time)
Rod Length
26.4–26.5 inches overall
Rod Diameter
1-1/4 inches
Material
Spring steel / Plastic end caps
Color
Brass / Black / White / Pink
Lubrication
Pre-coated with grease — wear gloves during installation
Error Codes Resolved
dc (out of balance), UE (unbalanced load)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves.
Frequently Asked Questions
What is the difference between DC97-16350U and DC97-16350V?
Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering.
Why must I replace all 4 rods instead of just the broken one?
All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair.
Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U?
Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U.
What do error codes dc and UE mean on Samsung washers?
Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases.
Is this an OEM or aftermarket part?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO Washer Replacement Part
XPARTCO W10144820 Water Inlet Valve Assembly Replaces WPW10144820
Complete hot/cold washer inlet valve assembly with vacuum break and built-in thermistor for water-temperature sensing.
Product Overview
The XPARTCO W10144820 Washer Water Inlet Valve Assembly controls hot and cold water flow into compatible Whirlpool-built top-load washers. The complete assembly includes the hot-water valve, cold-water valve, vacuum-break section, and thermistor used by the washer to sense incoming water temperature.
This is a quality XPARTCO aftermarket replacement part designed to replace WPW10144820 on compatible models.
Quick Answer
Use this assembly when a compatible washer fills slowly, will not fill, overfills because a valve does not close correctly, or has a failed inlet thermistor. Verify the full washer model number before ordering because similar Whirlpool-built washers may use different valve assemblies.
Common Problems This Part May Fix
Washer fills slowly
Washer will not fill with hot or cold water
Incorrect water temperature
Water continues entering after fill should stop
Intermittent filling
Fault related to inlet water-temperature sensing
Cracked or leaking inlet valve body
Replaces and Cross-References
WPW10144820, W10144820, W10311458, WPW10144820VP, 33190126, 33190127, W10140914, W10140911, PD00002258, EAP11749042, AP6015761, AWP49944, PS11749042.
Cross-reference numbers are provided for identification. XPARTCO is an aftermarket replacement brand and is not manufactured by Whirlpool.
Compatibility
Fits select Whirlpool-built top-load washers sold under Whirlpool, Maytag, Amana, Admiral, Crosley, Estate, Inglis, Kenmore, and Roper brands. Compatible examples include:
WTW5505VQ1
WTW5300VW2
1CWTW5200VQ1
NTW4500XQ0
NTW4600VQ1
RTW4305VQ1
MVWC400VW1
110.29722801
CAWSS16445WQ0
Important: This is only a partial model list. Confirm the complete washer model number and original valve assembly before purchase.
Key Features
Quality XPARTCO aftermarket replacement
Complete hot/cold inlet valve assembly
Built-in thermistor for water-temperature sensing
Integrated vacuum-break section
Controls incoming washer water flow
Replaces WPW10144820 and earlier numbers
Product Specifications
XPARTCO Part Number
W10144820
Replaces
WPW10144820
Part Type
Washer Water Inlet Valve Assembly
Configuration
Hot + Cold Inlet Valve Assembly
Temperature Sensor
Built-In Thermistor
Vacuum Break
Included
Condition
New
Part Quality
Aftermarket Replacement
Quantity
1 Assembly
Installation Notes
Unplug the washer and shut off both hot and cold water supplies.
Relieve hose pressure and disconnect the inlet hoses.
Photograph the original wiring and hose routing before removal.
Inspect inlet screens and supply hoses for restriction or damage.
Transfer connections only after confirming the replacement matches the original assembly.
Reconnect hot and cold hoses to the correct inlets and check carefully for leaks.
Restore power and water, then run a fill test to confirm proper hot/cold operation and temperature sensing.
Diagnostic tip: Slow filling can also be caused by clogged inlet screens, kinked hoses, low household water pressure, or partially closed supply valves.
Frequently Asked Questions
Does this assembly include the temperature sensor?
Yes. This valve assembly includes a thermistor used for incoming water-temperature sensing.
Does W10144820 replace WPW10144820?
This XPARTCO part is designed as an aftermarket replacement for the OEM WPW10144820 valve assembly.
Is this a Genuine Whirlpool OEM valve?
No. It is a quality XPARTCO aftermarket replacement.
Will this fit every Whirlpool top-load washer?
No. Whirlpool-built washers use several different inlet-valve designs, so the complete model number should be verified before ordering.
Shop With Confidence
Verify your washer model and original valve number before ordering. Our compatibility team can help confirm whether XPARTCO W10144820 is correct for your appliance.
Hot + Cold ValveBuilt-In ThermistorXPARTCO ReplacementCompatibility Support
XPARTCO W10316760 Refrigerator Thermistor Sensor
The XPARTCO W10316760 is an aftermarket replacement temperature thermistor compatible with a wide range of Whirlpool-built refrigerators sold under the Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef brands. The thermistor sits inside the fresh food or freezer compartment and continuously reports internal temperature back to the electronic control board, which uses that reading to cycle the compressor, evaporator fan, and damper to keep the compartment in range. When the thermistor drifts out of calibration or fails outright, the control board loses an accurate temperature signal and the refrigerator commonly responds with erratic cooling, a warmer-than-normal compartment, food freezing when it shouldn't, or a flashing/blank temperature display.
This XPARTCO version is built with a quick-connect mounting clip, so it plugs in without cutting or splicing wires — unlike the genuine Whirlpool OEM part, which ships as a splice-in kit requiring you to cut the old thermistor's leads and join the new ones with included wire connectors. It directly replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944, and additional cross-reference numbers listed below. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10316760 Refrigerator Thermistor Sensor fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators that are running warm, running constantly, freezing food unexpectedly, or showing a flashing/blank temperature display. This version uses a quick-connect clip — no wire cutting or splicing like the genuine Whirlpool splice-kit version requires. Replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944. Classic symptom: fridge or freezer running warmer than the setting, or running nonstop.
Common Problems This Part Fixes
Refrigerator or freezer running noticeably warmer than the temperature setting
Fridge running constantly and never cycling off
Temperature display flashing, showing dashes, or displaying an error code
Food freezing in the fresh food compartment when it shouldn't be
Compressor and fans not cycling normally, or running nonstop
Inconsistent or swinging temperature readings on the display
One compartment (fridge or freezer) running warm while the other stays normal
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers:
W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermistor is used across a wide range of Whirlpool-built refrigerators from the following brands:
Whirlpool refrigerators (including WRF535SMBM00, WRX735SDBM00, and related French door / side-by-side models)
KitchenAid refrigerators (including KBFS22EWBL1, KBFS22EWMS1, KBFS22EWMS3, KBFS22EWMS5, KBFS22EWMS7, KBFS22EWWH1)
Maytag refrigerators (select Whirlpool-built models, including KRFF302ESS)
Jenn-Air refrigerators (select Whirlpool-built models, including MFI2269VEM)
Amana refrigerators (select models)
Inglis refrigerators (select models)
Magic Chef refrigerators (select models)
Note: Many of these refrigerators use separate thermistors for the fresh food and freezer compartments, so confirm which sensor location your model uses before ordering — appearance can be similar across positions. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Direct-fit replacement refrigerator temperature thermistor — reports compartment temperature to the electronic control board
Resolves "running warm," "running constantly," "freezing food," and "flashing display" symptoms caused by thermistor failure
Quick-connect mounting clip — no wire cutting or splicing required
Matches OEM electrical resistance curve for accurate temperature sensing
Approximate lead length ~5 inches
Replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944, and additional cross-reference numbers
Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
XPW10316760
OEM Part Number
W10316760
Part Type
Refrigerator Temperature Thermistor / Sensor
Condition
Aftermarket Replacement
Application
Whirlpool-Built Refrigerators (Fresh Food / Freezer Compartment)
Mounting
Quick-connect clip (no splicing)
Approx. Lead Length
~5 inches (may vary by model)
Compatible Brands
Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, Magic Chef
Installation Notes
⚠️ Disconnect Power Before Starting Unplug the refrigerator or shut off power at the breaker before accessing internal panels. Locate the thermistor at its mounting position inside the fresh food or freezer compartment (location varies by model — consult your model's parts diagram if unsure). Photograph the wire routing before disconnecting. On this XPARTCO version, simply unplug the old thermistor's connector from the wiring harness — no cutting or splicing needed. Release the old thermistor from its mounting clip or bracket and remove it. Install the new thermistor in the same position, securing it in its mounting clip. Plug the new thermistor's connector into the wiring harness, matching your photos. Reassemble any panels removed for access. Restore power and allow the refrigerator several hours to stabilize before checking temperatures. Tools needed: nut driver or screwdriver (for panel access), needle-nose pliers (for mounting clip).
Frequently Asked Questions
Is this the same as the genuine Whirlpool W10316760 thermistor?
It's a direct-fit aftermarket equivalent, not the genuine Whirlpool part. The key functional difference is installation: the genuine OEM version ships as a splice-in kit requiring you to cut the old wires and use included splice connectors, while this XPARTCO version has a quick-connect clip that simply plugs in — no splicing tools needed.
Will this fit my refrigerator?
W10316760 and its cross-reference numbers span a wide range of Whirlpool-built models across several brands. Confirm fit using your refrigerator's exact model number before ordering, since visually similar thermistors are used across different platforms and compartment locations. Contact our support team with your model number if you're unsure.
My fridge is warm but the freezer is fine (or vice versa) — could this part be the cause?
Yes. Most of these refrigerators use separate thermistors for the fresh food and freezer compartments, so a single failed sensor can cause one section to run warm while the other stays normal. Confirm which sensor location your model uses before ordering.
Do I need any tools to install this?
Basic hand tools to access the interior panel (typically a nut driver or screwdriver) plus needle-nose pliers to release the old mounting clip. Because this version uses a plug-style connector, no wire strippers, cutters, or splice connectors are needed — unlike the genuine OEM splice-kit version.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical resistance curve, mounting position, and temperature-sensing function of the original W10316760 thermistor used in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
W11481722 Genuine OEM Whirlpool Washer Shift Actuator
The W11481722 is a genuine Whirlpool OEM shift actuator (gear case) for Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers. Mounted at the bottom of the washer, this component does two jobs in one assembly: it physically shifts the transmission between modes by moving an arm on the cam assembly, engaging and disengaging either the basket or the agitator/washplate depending on what the cycle calls for, and it houses the tachometer that reports drum speed back to the control board throughout the cycle.
Rated 120V, 60Hz, with a 6-pin wire connector for a direct plug-in fit. Because this single part handles both mechanical shifting and speed sensing, a failure here can produce a range of symptoms depending on which function is affected: the washer may fail to spin or agitate properly, get stuck in one mode without transitioning to the other, or the control board may throw an error code related to a lost tachometer signal or improper basket engagement. It directly replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781.
Quick Answer
The W11481722 Genuine OEM Whirlpool Washer Shift Actuator fixes Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers that won't spin or agitate properly, get stuck in one mode, or throw a tachometer/basket-engagement error code. 120V, 60Hz, 6-pin connector. Replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781. This part also contains the tachometer — a single failure here can affect both cycle shifting and speed sensing at once.
Common Problems This Part Fixes
Washer won't spin
Washer won't agitate
Washer gets stuck in one mode and won't transition between agitate and spin
Error code related to a tachometer signal or basket engagement
Basket doesn't engage or disengage correctly during the cycle
Cycle stalls partway through as the control loses accurate speed feedback
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer shift actuator directly replaces the following OEM and cross-reference part numbers:
W11481722, W10597177, WPW10597177, W11237117, W11398781, AP6990751, AWP45140, EAP16221077, PD00067016, PS16221077
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This shift actuator is compatible with select Whirlpool top-load washers, and also fits select Maytag, Amana, Crosley, and Kenmore washers built on the Whirlpool platform, including model numbers such as:
WTW5100HW1, WTW5100HC1, WTW6120HC1
WTW4616FW3, WTW4655JW2, WTW4715EW0, WTW4715EW2
WET4027HW2, WETLV27HW3, WGT4027HW0, WGTLV27HW0
NTW4516FW0, NTW4516FW2, NTW4516FW4, NTW4519JW2
NTW4601BQ1, NTW4605EW0, NTW4611BQ1, NTW4615EW0, NTW4631BQ1, NTW4635EW0, NTW4651BQ1, NTW4655EW0, NTW4701BQ1, NTW4705EW0, NTW4750BQ1, NTW4755EW0
Crosley VAW3584GW0, VAW3584GW1, VAW3584GW2
Kenmore 110-series models (110.xxxxx)
Note: Always verify your full model number before ordering, since Whirlpool uses several different shift actuator designs across its washer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified shifting mechanism and tachometer calibration
Combines two functions in one assembly: transmission mode shifting and drum speed sensing
Resolves "won't spin," "won't agitate," "stuck in one mode," and "tachometer error code" symptoms
Rated 120V, 60Hz
6-pin connector for a direct plug-in electrical fit
Direct drop-in replacement — mounts to the original gear case position
Replaces W10597177, W11237117, W11398781, WPW10597177, and W10625252
Compatible with Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W11481722
Part Type
Washer Shift Actuator (Gear Case)
Condition
Genuine OEM
Brand
Whirlpool
Location
Bottom of the washer, in the gear case
Function
Shifts transmission between agitate/wash and spin modes; houses the tachometer
Voltage
120V
Frequency
60 Hz
Connector
6-pin
Material
Metal
Repair Difficulty
Moderate — gear case access required
Quantity
1 shift actuator
Compatible Brands
Whirlpool, Maytag, Amana, Crosley, Kenmore
Installation Notes
⚠️ Unplug Washer Before Starting — Note Cam Position Before Removal Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shift actuator is through the gear case at the bottom of the washer, which typically requires tipping the washer back or removing surrounding panels per your model's service instructions to reach it. Photograph the wiring harness connection and the actuator's mounting position before disconnecting anything. Disconnect the 6-pin wiring harness connector from the old actuator, remove its mounting screws, and pull it free from the gear case. Install the new W11481722 in the same position, secure the mounting screws, and reconnect the 6-pin harness connector fully. Reassemble any panels removed for access, restore power, and run a full test cycle through both agitate and spin to confirm the washer shifts between modes correctly with no error codes. Tools needed: Phillips or nut driver screwdriver, work gloves.
Frequently Asked Questions
My washer is stuck in one mode — it will either agitate or spin, but not both. Is this the shift actuator?
Yes, this is a classic symptom of a failed shift actuator. This part is what physically moves the arm on the cam assembly to switch the transmission between agitate/wash mode and spin mode. If it fails, the washer can get mechanically stuck engaging only one of those two functions, since the shifting mechanism itself is no longer moving the cam correctly.
My control board shows a tachometer error. Why would that be the shift actuator and not something else?
Because this single part combines both the mechanical shifting function and the tachometer that reports drum speed to the control board, a failure inside the actuator can knock out the speed-sensing function even if the shifting mechanism is unaffected, or vice versa. A tachometer-related error code is a direct signal that this component — not a separate sensor — is the likely cause.
Is this a difficult repair?
It's a moderate repair, since accessing the gear case at the bottom of the washer typically requires tipping the unit back or removing surrounding panels, depending on your specific model. It's within reach for a confident DIYer with basic hand tools, but budget more time than a simple top-panel swap.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original shifting mechanism, tachometer calibration, and 6-pin harness configuration of the shift actuator originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
