Search results for "washer switches"

Genuine OEM Frigidaire / Electrolux Washer Part 134762010 Washer Genuine OEM Water Level Pressure Switch Monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Product Overview The Frigidaire 134762010 Washer Water Level Pressure Switch senses changes in air pressure through the washer pressure hose to monitor the amount of water inside the tub. It signals the washer control system when the correct water level has been reached so the appliance can fill, wash, drain, and advance through the cycle correctly. This is a new Genuine OEM Frigidaire / Electrolux replacement part manufactured to the original equipment specifications for proper fit, electrical connection, and operation in compatible washers. Quick Answer 134762010 is a Genuine OEM water-level pressure switch for select Frigidaire, Electrolux, Kenmore, and Crosley front-load washers. It replaces 7134762010. This listing is for the pressure switch only; the pressure hose, clamp, wiring harness, and mounting hardware are not included unless specifically shown. Common Problems This Part May Fix Washer overfills with water Washer does not fill or underfills Incorrect or inconsistent water level Cycle stops or will not advance Washer does not drain or complete the cycle correctly E35 or another water-level-related error on applicable models Replaces and Cross-References 134762010, 1482962, 7134762010, AH2349296, AP4368525, AFR14413, EA2349296, PD00007813, PS2349296. 134762010 is the current manufacturer part number. Other numbers are previous manufacturer or retailer cross-references. Compatibility Designed for select front-load washers manufactured by Electrolux and sold under Frigidaire, Electrolux, Kenmore, and Crosley brand names. Confirmed model examples include: 41741100000 41744130000 EIFLS55IRR0 EIFLS60JIW1 FAFS4473LN0 FAFW3921NW0 FFFW5000QW0 CFW4700LW0 CFW7400QW0 Important: This is a partial compatibility list. Pressure switches can look alike while using different settings, terminals, mounting tabs, or control calibration. Verify the complete washer model number before ordering. Key Features Genuine OEM Frigidaire / Electrolux replacement part Monitors the water level inside the washer tub Signals the control system when the correct fill level is reached Supports proper filling, washing, draining, and cycle operation Snap-tab mounting design on compatible models Designed for original fit and electrical connection Product Specifications Manufacturer Part Number 134762010 Brand Frigidaire / Electrolux Part Type Washer Water Level Pressure Switch Condition New Quality Genuine OEM Application Front-Load Washing Machine Primary Function Senses and controls the washer water level Included One Water Level Pressure Switch Installation Notes Unplug the washer and shut off both water-supply valves. Remove the washer top panel as required for your model. Photograph the wire connector and pressure-hose connection before disconnecting them. Disconnect the electrical connector without pulling on the wires. Release the clamp and carefully remove the pressure hose. Remove the old switch and install the replacement in the same position. Reconnect the hose, clamp, and electrical connector, then reinstall the top panel. Diagnostic tip: Inspect the pressure hose for cracks, pinholes, blockage, moisture, loose connections, or trapped debris. A damaged or obstructed hose can cause the same symptoms as a failed pressure switch. Frequently Asked Questions Is 134762010 a genuine OEM part? Yes. It is a Genuine OEM Frigidaire / Electrolux washer water-level pressure switch. What does the pressure switch do? It monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Which part number does it replace? It replaces previous manufacturer part number 7134762010. Does this include the pressure hose? No. The listing is for the pressure switch only unless additional components are specifically shown and stated as included. Will it fit every Frigidaire or Electrolux washer? No. Verify the complete appliance model number and required manufacturer part number before purchasing. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and operation. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers Product Description Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts. Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083. Compatibility: Compatible with models including but not limited to: Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS Other brands: Select models requiring DC96-01703G Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G. 🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA). Product Specification Part Number: XPDC96-01703G Component Type: Washer water level pressure switch Material: Durable plastic housing with metal contacts Terminal Type: Electrical connector. Operating Conditions: Suitable for high-humidity washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO EBF61315802 Washer Door Lock Switch The XPARTCO EBF61315802 is an aftermarket replacement washer door lock switch assembly compatible with a wide range of LG front-load washers and Kenmore 796-series front-load washing machines. The door lock switch is mounted on the front panel just inside the door opening — when the door is closed, the door's striker engages the lock and the switch reports back to the control board that the door is securely closed. The lock then engages electromagnetically to physically prevent the door from being opened during the wash and spin cycles, eliminating the risk of water leaks and protecting the user from the high-speed spinning drum. When this part fails, the washer will not start (since the control board can't confirm the door is locked), will stop mid-cycle, may display DE1 or DE2 error codes, may not actually lock the door (allowing it to open during a cycle), or may leak water around the door. Rated 125V AC, 60Hz, with a 3-pin connector. It directly replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, and PD00008063. Often replaced alongside the door lock strike (MFG63099101, sold separately), which is the matching component on the door itself. Installs in 15–20 minutes with basic hand tools — no full front panel removal needed on most models. Quick Answer The XPARTCO EBF61315802 Washer Door Lock Switch fixes LG and Kenmore 796-series front-load washers that won't start, won't lock the door, stop mid-cycle, display DE1 or DE2 error codes, allow the door to open during a cycle, or leak water around the door. 125V AC, 60Hz, 3-pin connector. Replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, PD00008063. Often paired with the door lock strike (MFG63099101, sold separately). Common Problems This Part Fixes Washer won't start — control board not detecting a locked door Door fails to lock at the start of the cycle DE1 or DE2 error codes displayed on the control panel Washer stops mid-cycle due to a door lock fault Door pops open or unlatches during the wash or spin cycle (safety concern) Water leaking around the door during operation — door not sealing because the lock isn't fully engaging Stuck, aged, worn, or broken door lock Door open/close action no longer smooth — lock binding Repeated mid-cycle shutdowns or interruptions Replaces Part Numbers This door lock switch directly replaces the following OEM and cross-reference part numbers: EBF61315802, EBF62534401, AP6992889, PS16223547, ALG54705, AP5672154, PD00008063, PS7792232, B088MG37Y9 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock switch is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3180CW series LG front-load washers — WM3250HRA, WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HWA, WM3400CW, WM3460CV, WM3488HS, WM3488HW, WM3499HVA, WM3500CW, WM3555HWA series LG front-load washers — WM3570HVA, WM3570HWA, WM3600HVA, WM3670HVA, WM3670HWA, WM3700HVA, WM3700HWA series LG front-load washers — WM3770HVA, WM3770HWA, WM3900HBA, WM3900HWA, WM3997HWA, WM3998HBA series LG front-load washers — WM4070HVA, WM4070HWA, WM4200HBA, WM4200HWA, WM4270HVA, WM4270HWA, WM4370HKA, WM4370HWA, WM4500HBA series LG front-load washers — WM5000HVA, WM5000HWA, WM8000HVA, WM8000HWA, WM8100HVA, WM8100HWA, WM8500HVA series LG front-load washers — WM9000HVA, WM9000HWA, WM9500HKA series LG WashTower units — WKE100HVA, WKE100HWA, WKEX200HBA, WKEX200HWA, WKG101HVA, WKG101HWA, WKGX201HBA series LG Studio models — GCWP1069CD/CD1/CD2/CD3, GCWW1069CD7, GCWW1069CS7 series Kenmore / Sears front-load washers — 796-series (79641002610, 79641072310, 79641073310, 79641182310, 79641183310, 79641262610, 79641282310, 79641283310, 79641302610, 79641303610, 79641382410, 79641383410, 79641392610, 79641482410, 79641572210, 79641573210, 79641582410, 79641962610, 79641963610, 79641982410, and many related models) Note: The door lock switch (EBF61315802) and the door lock strike (MFG63099101) are two separate components that work together — if both have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new switch. Always verify your model number before ordering. Key Features Door lock switch assembly — detects when the door is closed and electromagnetically locks it during wash and spin cycles Resolves DE1 and DE2 error codes caused by door lock failure on compatible LG and Kenmore washers Prevents water leaks and protects the user by ensuring the door cannot open during operation 125V AC, 60Hz — correct electrical specifications for compatible LG and Kenmore washers 3-pin connector for secure wire harness fit Replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, and PD00008063 Compatible with LG WM1388, WM3050, WM3170, WM3250, WM3370, WM3500, WM3570, WM3670, WM3770, WM3900, WM3997, WM4070, WM4270, WM4370, WM5000, WM8000, WM8100, WM8500, WM9000, WM9500 series and Kenmore 796-series front-load washers Compatible with LG WashTower (WKEX, WKE, WKG, WKGX) units Often replaced together with the door lock strike (MFG63099101, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools (no full front panel removal needed on most models) Product Specifications Part Number EBF61315802 Part Type Washer Door Lock Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore Samsung-built platform) Voltage 125V AC Frequency 60 Hz Connector 3-pin connector Lock Type Electromagnetic Error Codes Resolved DE1, DE2 (door lock errors) Often Paired With Door Lock Strike (MFG63099101, sold separately) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. On most LG and Kenmore front-load models, you can replace the door lock switch without removing the whole front panel — a much faster repair than expected. Open the washer door (if the door is stuck locked, use a putty knife to pry the white latch on the door lock assembly through the bottom service opening, then open the door). Remove the spring-loaded wire clamp securing the door boot to the front panel — needle-nose pliers help here. Peel back the rubber door boot from the front panel to expose the rear of the door lock switch. Remove the 2 Phillips screws holding the switch to the front panel. Reach in and pull the switch out through the boot opening. Disconnect the wire harness from the old switch. Connect the wire harness to the new EBF61315802, position it in place, and secure with the 2 mounting screws. Press the rubber door boot back fully into the groove at the front panel — this is the trickiest part of the install (an extra pair of hands helps). Reinstall the spring-loaded wire clamp around the boot to secure it. Restore power and test by closing the door and starting a cycle. Tools needed: Phillips screwdriver, needle-nose pliers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What do error codes DE1 and DE2 mean on LG washers? DE (Door Error) codes on LG front-load washers indicate the control board cannot confirm the door is properly closed and locked. DE1 typically appears when the door switch reports the door as open at the start of a cycle, and DE2 typically appears when the door signal is lost during a cycle. Both can be caused by a failed door lock switch, a worn or broken door lock strike (MFG63099101) on the door itself, or a damaged wiring harness. Replacing the EBF61315802 door lock switch resolves these codes when the switch is the cause; if the codes return after replacement, the strike on the door or the harness should be inspected next. Do I need to replace the door lock strike (MFG63099101) too? Not always, but often. The door lock strike is the matching component mounted on the door itself — it's the part that the switch's electromagnetic lock grips when the door closes. If the strike is worn, cracked, or its plastic teeth are broken, the new switch won't lock reliably even if it's working perfectly. Inspect the strike on the door for visible damage before replacing just the switch. Many repair scenarios call for replacing both at the same time, since both wear together and the parts complement each other. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing switch has failed, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the installation. Always disconnect power from the washer before attempting this. Do I really not need to remove the front panel? Correct — on most LG and Kenmore front-load models, you can replace the door lock switch by working through the door opening after pulling back the rubber door boot. This avoids the much more involved process of removing the entire front panel. The trickiest part of the repair is pressing the rubber door boot back into its groove on the front panel after the switch is installed — an extra pair of hands is helpful for this step. The whole repair typically takes 15–20 minutes. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the electrical specifications (125V AC, 60Hz), 3-pin connector configuration, electromagnetic lock function, and dimensions of the original EBF61315802 door lock switch used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC96-01703H Washer Water Pressure Switch - Compatible with Samsung Washers Product Description Ensure your Samsung washer operates flawlessly with the replacement DC96-01703H Washer Water Pressure Switch. This replacement part is designed for select Samsung washing machines, providing precise water level control to prevent overfilling, underfilling, or water leakage. It resolves issues like error codes, inconsistent water levels, or failure to start wash cycles, delivering reliable performance for your appliance. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: DC96-01703H, PD00030634, EAP8764044, AP5799898, 3997570, PS8764044. Compatibility: Compatible with models including but not limited to: Samsung: WA48J7700AW/A2, WA48H7400AW/A2, WA50F9A7DSP/A2, WA52M7750AV/A4, WA56H9000AP/A2 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung washing machines. 🔥 Specifications: Water pressure switch with electrical connectors and 28" hose attachment. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves water level issues, error codes, and improper filling. Product Specification Part Number: XPDC96-01703H Component Type: Washer water pressure switch Mounting: Secures to washer control panel with screws or clips Operating Conditions: Suitable for washer environments Installation Notes: Safety First: Disconnect the washer from power and water sources before installation. Follow the owner’s manual for guidance. Shop for high-quality replacement appliance parts with a 30-day return policy. Fix your washer today! Add to cart now for a reliable solution!

Read more less

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

XPARTCO WH01X27954 Washer Lid Switch (Old Style) Product Overview The XPARTCO WH01X27954 Washer Lid Switch (Old Style) is designed to restore proper lid detection and washer operation. This high-quality replacement detects whether the washer lid is closed, allowing safe operation during wash and spin cycles. A broken or faulty switch can cause the washer not to start, stop mid-cycle, or fail to spin. Replacing it with this durable XPARTCO switch restores normal functionality and safety performance. Old-style GE lid switch (does not require harness replacement). Quick Answer If your washer will not spin, drain, or start properly, a faulty WH01X27954 lid switch may be the cause. Replacing this old style washer lid switch helps restore normal washer operation and cycle performance. Replaces Part Numbers Replaces OEM part number: WH08X32697, WH01X27954, WH08X31577, WH01X24114, WH01X26114, 290D1580P001, 290D1580P004, 290D1580P002, 290D1580P003, WH08X31577, AP7015047, PS16554755. Compatibility This washer lid switch is compatible with select GE, Hotpoint, and other compatible top-load washers that use the old style lid switch design. Example compatible models include (but are not limited to): GE GTW220ACK1WW GTW220ACK2WW GTW220ACK3WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW330ASK2WW GTW330ASK3WW GTW330ASK4WW GTW330ASKWW GTW335ASN0WW GTW335ASN2WW GTW335ASNWW GTW460AMJ0WW GTW460AMJ1WW GTW460AMJ2WW GTW460AMJ3WW GTW460AMJ4WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW335ASN0WW. GE Top-Load Washers Hotpoint Washers Old Style Lid Switch Applications Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Washer not spinning Washer not draining Washer not starting cycle Lid switch not detecting closed lid Key Features Designed for old style washer lid switch applications Helps restore safe and proper washer operation High-quality aftermarket replacement Durable construction for reliable performance Product Specifications Part Number: WH01X27954 Part Type: Washer Lid Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Top-Load Washers Style: Old Style Troubleshooting Guide Washer fills but does not spin → Lid switch may be faulty Washer will not start cycle → Lid switch may not detect closed lid Washer stops before spin cycle → Defective lid switch can interrupt operation When Should You Replace This Lid Switch? Replace this lid switch if your washer does not start, spin, or drain properly, or if the switch no longer detects when the lid is closed. Installation Notes ⚠️ Disconnect power before installation. Access the lid switch area according to your washer design and install the replacement securely. Refer to your appliance manual if needed. Related Parts Washer Lid Strike Washer Timer Washer Door or Lid Lock Components Frequently Asked Questions Will this lid switch fit my washer?This switch fits select GE and compatible washers that use the old style lid switch. Always verify your model number. What does a washer lid switch do?It detects whether the washer lid is closed so the machine can operate safely. What are signs of a bad lid switch?Common signs include the washer not spinning, not starting, or stopping before the cycle completes. Is this the old style version?Yes, this listing is for the old style WH01X27954 washer lid switch. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality aftermarket parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

Genuine OEM WH08X37938 Washer Lid Switch Assembly The WH08X37938 is a genuine OEM lid switch (lid lock) assembly from GE for GE and Hotpoint top-load washers, also used on select Kenmore models. The assembly locks the lid while the washer is running and releases it when the cycle ends, and it tells the control board the lid is closed and it's safe to run. When it wears out, cracks, or fails electrically, the washer may refuse to start, stop in the middle of a cycle, show a lid or door lock error, or fail to lock the lid at all. This assembly replaces the original lock and switch as a unit, so you do not have to diagnose which internal contact has failed. As a genuine OEM part, not an aftermarket equivalent, it matches the original factory fit and specification. It mounts on the washer cabinet with an electrical connector and is a straightforward repair, usually done in under an hour. Quick Answer The Genuine OEM WH08X37938 Lid Switch Assembly fixes a GE or Hotpoint top-load washer that won't start, stops mid-cycle, won't lock the lid, or shows a lid or door lock error because the lid lock is worn or has failed. Complete replacement lock and switch assembly, genuine OEM. Classic symptom: you close the lid and nothing happens, or the washer starts then stops and signals a lid or lock fault. Common Problems This Part Fixes Washer won't start when the lid is closed Washer stops partway through the wash, rinse, or spin Lid will not lock, or stays locked after the cycle ends Lid or door lock error codes Loose, cracked, or visibly damaged lid lock Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid switch assembly replaces the following part numbers: WH08X37938, WH08X32697, WH02X24399, WH08X32657, WH01X26694, WH01X24112, WH01X24114, WH01X26114, WH01X27954, WH08X31577, WH08X31222, 290D1580P001, 290D1580P002, 290D1580P003, 290D1580P004, 290D3070P001, EG-380843 M, AGE26076, AP7225583, EAP17626546, OEM21676758, PD00087323, PS17626546 These are earlier GE numbers for the lid lock, as the part was updated over time. If your old lock or parts diagram shows any of them, match against this list. Compatibility This assembly is listed for select top-load washers from: GE and Hotpoint, including GTUN275EM0WW, GTUN275GM0WW, GTUP240EM0WW, and GTUP240EM2WW Kenmore, including 363.71542211, 363.71542310, and 363.71542410 Note: The model list above is only a sample, and lid locks differ between GE washer generations. Confirm fit by matching the number on your old lock or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This part is for top-load washers. Key Features Genuine OEM GE lid switch (lid lock) assembly, not an aftermarket equivalent Replaces the lock and switch as a unit, with no need to find the failed contact Restores starting, locking, and unlocking at the end of the cycle Cross-references to WH08X32697, WH08X31577, and other earlier GE numbers Fits select GE, Hotpoint, and Kenmore top-load washers Mounts on the cabinet with a plug-in electrical connector Product Specifications Part Number WH08X37938 OEM Part Number WH08X37938 Part Type Washer Lid Switch (Lid Lock) Assembly Condition Genuine OEM Application Select GE, Hotpoint & Kenmore Top-Load Washers Installation Notes ⚠️ Unplug Power and Shut Off Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Open the lid and, following your model's service guide, remove the top panel or cabinet section to reach the lid lock mounted on the cabinet. Note the position of the old assembly, disconnect its wiring connector, and remove the screws holding it in place. Fit the new assembly in the same position, secure it, and reconnect the connector. Reassemble the washer, restore power and water, and run a short cycle to confirm the lid locks, the washer starts, and the lid releases at the end. Frequently Asked Questions My washer won't start with the lid closed. Is this the part I need? A failed lid lock is a common cause. The control board won't start a cycle unless it sees the lid is closed and locked. Check that the lid closes fully and that nothing is blocking it. If it still won't start, the lid lock is a likely cause. Is a lid switch the same as a lid lock? On these washers, the lid switch and lock are combined in one assembly, which this part replaces. My old part is marked WH08X32697 or WH08X31577. Will this work? Those numbers are on the Replaces list. Compare the connector and mounting against your old part, or contact our support team with your model number and we'll confirm. Will this fit my front-load washer? No. This is for top-load washers. Is this an OEM part? Yes. This is a genuine OEM GE part, not an aftermarket equivalent, so it matches the original factory fit and specification. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH08X37938 Washer Lid Switch Assembly The XPARTCO WH08X37938 is an aftermarket replacement lid switch (lid lock) assembly for GE and Hotpoint top-load washers, also used on select Kenmore models. The assembly locks the lid while the washer is running and releases it when the cycle ends, and it tells the control board the lid is closed and it's safe to run. When it wears out, cracks, or fails electrically, the washer may refuse to start, stop in the middle of a cycle, show a lid or door lock error, or fail to lock the lid at all. This assembly replaces the original lock and switch as a unit, so you do not have to diagnose which internal contact has failed. It mounts on the washer cabinet with an electrical connector and is a straightforward repair, usually done in under an hour. Quick Answer The XPARTCO WH08X37938 Lid Switch Assembly fixes a GE or Hotpoint top-load washer that won't start, stops mid-cycle, won't lock the lid, or shows a lid or door lock error because the lid lock is worn or has failed. Complete replacement lock and switch assembly, aftermarket. Classic symptom: you close the lid and nothing happens, or the washer starts then stops and signals a lid or lock fault. Common Problems This Part Fixes Washer won't start when the lid is closed Washer stops partway through the wash, rinse, or spin Lid will not lock, or stays locked after the cycle ends Lid or door lock error codes Loose, cracked, or visibly damaged lid lock Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid switch assembly replaces the following part numbers: WH08X37938, WH08X32697, WH02X24399, WH08X32657, WH01X26694, WH01X24112, WH01X24114, WH01X26114, WH01X27954, WH08X31577, WH08X31222, 290D1580P001, 290D1580P002, 290D1580P003, 290D1580P004, 290D3070P001, EG-380843 M, AGE26076, AP7225583, EAP17626546, PD00087323, PS17626546 These are earlier GE numbers for the lid lock, as the part was updated over time. If your old lock or parts diagram shows any of them, match against this list. Compatibility This assembly is listed for select top-load washers from: GE and Hotpoint, including GTUN275EM0WW, GTUN275GM0WW, GTUP240EM0WW, and GTUP240EM2WW Kenmore, including 363.71542211, 363.71542310, and 363.71542410 Note: The model list above is only a sample, and lid locks differ between GE washer generations. Confirm fit by matching the number on your old lock or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This part is for top-load washers. Key Features Aftermarket replacement lid switch (lid lock) assembly Replaces the lock and switch as a unit, with no need to find the failed contact Restores starting, locking, and unlocking at the end of the cycle Cross-references to WH08X32697, WH08X31577, and other earlier GE numbers Fits select GE, Hotpoint, and Kenmore top-load washers Mounts on the cabinet with a plug-in electrical connector Product Specifications Part Number XPWH08X37938 OEM Part Number WH08X37938 Part Type Washer Lid Switch (Lid Lock) Assembly Condition Aftermarket Replacement Application Select GE, Hotpoint & Kenmore Top-Load Washers Installation Notes ⚠️ Unplug Power and Shut Off Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Open the lid and, following your model's service guide, remove the top panel or cabinet section to reach the lid lock mounted on the cabinet. Note the position of the old assembly, disconnect its wiring connector, and remove the screws holding it in place. Fit the new assembly in the same position, secure it, and reconnect the connector. Reassemble the washer, restore power and water, and run a short cycle to confirm the lid locks, the washer starts, and the lid releases at the end. Frequently Asked Questions My washer won't start with the lid closed. Is this the part I need? A failed lid lock is a common cause. The control board won't start a cycle unless it sees the lid is closed and locked. Check that the lid closes fully and that nothing is blocking it. If it still won't start, the lid lock is a likely cause. Is a lid switch the same as a lid lock? On these washers, the lid switch and lock are combined in one assembly, which this part replaces. My old part is marked WH08X32697 or WH08X31577. Will this work? Those numbers are on the Replaces list. Compare the connector and mounting against your old part, or contact our support team with your model number and we'll confirm. Will this fit my front-load washer? No. This is for top-load washers. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the GE WH08X37938. If you prefer a genuine OEM assembly, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304511335 Washer Water Level Pressure Switch – Compatible with Frigidaire & Electrolux Washers Product Description Restore accurate water level control and proper washer operation with the XPARTCO 5304511335 Washer Water Level Pressure Switch. It is responsible for detecting the water level inside the washer tub and ensuring accurate water level control during the wash cycle. It detects the pressure changes caused by the water level, allowing the washer to adjust the water intake accordingly. A faulty pressure switch can cause overfilling, under-filling, or cycles not advancing properly. Replacing it with this reliable XPARTCO component helps ensure correct water levels and consistent wash performance. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers 5304511335, 4584277, EAP12176459, AFR17584, OEM18784872, PD00046588, AP6261621, PS12176459. Compatibility This replacement washer water level pressure switch fits select Frigidaire, Electrolux, Gibson, Crosley, and Kenmore (Frigidaire-manufactured) washers. Common compatible models include (but are not limited to): Frigidaire FFTW4120SW1, FFTW4120SW0, FFTW4120SW, FFTW4120SW0 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pressure sensing performance 💧 Accurate Water Level Detection – Ensures proper fill and cycle control ⚙️ Fixes Common Issues – Resolves overfill, underfill, and cycle errors 🧩 Direct-Fit Design – Installs easily with existing hose and wiring 💰 Cost-Effective Repair – Affordable alternative to OEM pressure switches ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: 💧 Washer overfilling or underfilling ⚠️ Incorrect water levels during cycles 🔄 Cycle not advancing properly 🛑 Washer stops mid-cycle 🚫 No water or continuous filling Replacing this pressure switch can restore proper water level control and washer performance. 📐 Product Specification Part Number: 5304511335 Component Type: Washer Water Level Pressure Switch Function: Detects water level and signals control board Connection Type: Air hose + electrical connector Application: Washer water level sensing system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the control panel or top panel. Locate the pressure switch and disconnect the air hose and wiring. Remove mounting screws and remove the old switch. Install the new XPARTCO 5304511335 pressure switch. Reconnect hose and wiring, reassemble, and restore power. Run a test cycle to verify correct water levels. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore accurate water level control and reliable washer performance — Add to Cart Now for a dependable repair!

Read more less

XPARTCO W10810403 Washer Lid Switch Assembly The XPARTCO W10810403 is an aftermarket replacement lid lock assembly for Whirlpool Cabrio and Maytag Bravos XL top-load washers. Positioned on the underside of the washer lid, this assembly detects whether the lid is open or closed and locks it shut during the wash cycle, preventing the washer from spinning or agitating — and preventing the lid from being opened — while the cycle is running. This is a safety mechanism as much as a functional one, keeping users from contacting moving parts or being splashed by water or detergent mid-cycle. This assembly includes the lid lock mechanism and its wiring harness, and ships with a white bezel. Many of these lid locks also contain an internal fuse as part of the switch circuit — if that fuse blows, the symptom isn't limited to lid-related errors; it can prevent the entire control board from powering up at all, since the switch sits in the same circuit path. A failing lid lock typically shows up as the lid not closing or locking properly, the washer failing to start, the cycle stopping mid-way, or in more severe cases, a completely unresponsive control panel with no lights at all. It directly replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, and PS11731620. Quick Answer The XPARTCO W10810403 Washer Lid Switch Assembly fixes Whirlpool Cabrio, Maytag Bravos XL, and select Kenmore 600/700 Series top-load washers where the lid won't lock, the washer won't start, the cycle stops mid-way, or the control panel is completely unresponsive with no lights. White bezel. Replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, PS11731620. If your original lock has a grey bezel, you need part number W10861642 instead — same mechanism, different bezel color, so match the color of your existing lock before ordering. Common Problems This Part Fixes Lid won't lock or lock reliably during the cycle Lid won't open after a cycle finishes Washer won't start Washer won't agitate or spin because the lid isn't sensed as locked Cycle stops partway through Washer pumps but won't spin Control panel completely unresponsive with no lights, potentially from an internal fuse in the switch circuit Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select Whirlpool Cabrio and Maytag Bravos XL top-load washers, and also fits select Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea washers built on the same platform, including model numbers such as MVWB855DW1, MVWB865GW1, MVWB835DW3, and MVWB765FW4. Note — bezel color and lid lock platform both matter: This assembly has a white bezel. If your original lock has a grey bezel, order W10861642 instead — same lock mechanism, different bezel color. Separately, Whirlpool has used several distinct lid lock designs across its Cabrio-era washer lineup, including a different 3-wire electronic lock (our W11670519 listing) used on other Cabrio/MVW models. These are not the same part despite both serving Cabrio-platform washers. Always verify your full model number and match your original lock's exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement lid lock assembly — includes the lock mechanism and wiring harness Resolves "lid won't lock," "washer won't start," "cycle stops mid-way," and "unresponsive control panel" symptoms White bezel finish Safety mechanism that prevents lid opening and drum movement from occurring at the same time Direct drop-in replacement — mounts to the original position on the underside of the lid Replaces W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 Compatible with Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10810403 OEM Part Number W10810403 Part Type Washer Lid Lock/Switch Assembly Condition Aftermarket Replacement Application Whirlpool Cabrio / Maytag Bravos XL Top-Load Washers Bezel Color White (grey bezel = W10861642) Included Components Lid lock mechanism + wiring harness Location Underside of the washer lid Repair Difficulty Easy — basic hand tools Quantity 1 lid switch assembly Compatible Brands Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, Ikea Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the washer lid and locate the lid lock assembly mounted on its underside, typically secured with a couple of screws. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws, disconnect the wiring harness connector from the old assembly, and pull it free. Install the new W10810403 in the same position, reconnect the wiring harness connector fully, and secure the mounting screws. Restore power and run a test cycle to confirm the lid locks securely, the washer starts and completes a full cycle, and the lid unlocks normally once finished. Tools needed: multi-screwdriver, work gloves. Frequently Asked Questions My control panel has no lights at all. Could the lid lock really cause that? Yes, and this is a less obvious but documented cause. Some of these lid lock assemblies include an internal fuse as part of the switch circuit. If that fuse blows, it can prevent the control board from powering up entirely, producing a completely dark, unresponsive panel rather than a symptom that's obviously tied to the lid. If your washer has no lights and no response at all, this lock assembly is worth checking alongside the more obvious suspects. My old lock has a grey bezel. Can I still use this part? This specific listing has a white bezel. If your original lock is grey, order part number W10861642 instead — it's the same lock mechanism, just finished with a grey bezel to match certain washer trim colors. Using the wrong bezel color won't affect function, but it will look mismatched against your washer's lid. Is this the same lock used on all Cabrio washers? No — Whirlpool has used more than one lid lock design across its Cabrio-era lineup. This W10810403 is a distinct assembly from other Cabrio/MVW-platform locks, such as our W11670519 listing, which uses a different 3-wire electronic locking design. Always match your exact original part number rather than assuming any "Cabrio lock" will fit, since the mounting and electrical interface can differ between designs. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the locking mechanism, wiring harness, and bezel design of the original W10810403 lid lock assembly used in compatible Whirlpool Cabrio, Maytag Bravos XL, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE04X28977 Dryer Genuine Door Switch The WE04X28977 is a genuine GE dryer door switch for GE and Hotpoint dryers, and also fits select Haier, Monogram, and Café models built on the GE platform. This small latch-style switch communicates with the control board when the door is fully closed, allowing the drying cycle to safely begin, and signals the control board to stop the cycle if the door is opened during operation. White in color, measuring approximately 3"H x 2"W, weighing about 1 lb. Also known by the part number WE10X23879. Over time, this switch can become damaged from extended use or excessive force when closing the door. Symptoms of a failing door switch include the dryer failing to start, or the door not closing or latching properly. Replacing this switch requires a few basic tools and some slight disassembly of the dryer. It directly replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948. Quick Answer The WE04X28977 Dryer Genuine Door Switch fixes GE, Hotpoint, Haier, Monogram, and Café dryers that won't start or have a door that won't close or latch properly. White, small latch style, ~3"H x 2"W, ~1 lb. Replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948. This is a dryer part — it's sold individually and typically requires removing the front panel for access. Common Problems This Part Fixes Dryer won't start Door won't close or latch properly Dryer stops mid-cycle when the door is bumped or jostled Switch damaged from excessive force when closing the door Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer door switch directly replaces the following OEM and cross-reference part numbers: WE04X28977, WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select GE dryers, and also fits select Hotpoint, Haier, Monogram, and Café dryers built on the GE platform, including model numbers such as GTD42GASJ2WW, GTD45EASJ1WS, GTD45EASJ0WS, GTD45EASJ2WS, GTD42EASJ1WW, GTD42GASJ1WW, GTD72EBSN0WS, GTX22GASK0WW, GTD45GASJ2WS, GTD45GASJ1WS, GTX22EASK0WW, GTD42EASJ2WW, GTD42EASJ0WW, GTD42GASJ0WW, GTD72EBPN0DG, GTD45GASJ0WS, PTD60EBPR0DG, YTD74E2SN0WS, YTD74E2PN0DG, GTD84ECPN1DG, GTX52GASP0WB, PTD60GBSR0WS, GTD84GCPN0DG, VTD52EASR0WB, GTD84GCPN1DG, GTD84ECPN0DG, YTD74G2PN1DG, GTD84GCSN0WS, YTD74G2PN0DG, PTD60EBSR0WS, YTD74E2PN1DG, PTD60GBPR0DG, YTD74E2SN1WS, GTD84GCSN1WS, GTD65EBSJ4WS, VTD52GASR0WB, GTD84ECSN0WS, YTD74G2SN0WS, GTD84ECSN1WS, YTD74G2SN1WS, GTX52EASP0WB, HTX24GASK0WW, HTX24GASK0WS, HTX21EASK0WW, HTX21PASK0WW, HTX24EASK0WS, HTX24EASK0WW, HTX21GASK0WW, GTX65EBSJ2WS, GTD75ECPL0DG, GTD75GCPL0DG, GTD65GBSJ4WS, GTX42GASJ1WW, GTX65GBSJ2WS, GTD33PASK0WW, GTX33EASK0WW, GTX33GASK0WW, GTX60EBSJ0WS, GTD65EBSJ0WS, GTD65EBSJ3WS, GTX42EASJ1WW, 5TX62E9ST0WS, 5TX62E9ST1WS, 5TX62G9ST0WS, and ETD48EASW0WB. Note: This is a dryer part, sold individually. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified switch design Small latch-style door switch — communicates door status to the control board Resolves "won't start" and "door won't close" symptoms caused by switch failure White, approximately 3"H x 2"W, about 1 lb Also known as WE10X23879 Direct drop-in replacement matching the original mounting Replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948 Compatible with GE, Hotpoint, Haier, Monogram, and Café dryers Genuine OEM replacement — guaranteed fit, materials, and performance Sold individually Product Specifications Part Number WE04X28977 Also Known As WE10X23879 Part Type Dryer Door Switch (Small Latch Style) Condition Genuine OEM Brand GE Color White Height Approx. 3" Width Approx. 2" Weight Approx. 1 lb Repair Difficulty Easy to Moderate — front panel removal required Quantity 1 door switch (sold individually) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Turn the two screws located at the bottom corners of the front panel counter-clockwise until they come out, then slide the panel up and off the dryer to access the door switch. Locate the wires connected to the old door switch and disconnect them, noting their positions. Remove the mounting screws or clips securing the old switch and pull it free. Install the new WE04X28977 in the same position, reconnect the wires to their original positions, and secure the mounting hardware. Slide the front panel back into place and secure the two bottom corner screws. Restore power and test that the dryer starts normally with the door closed, and stops if the door is opened during a cycle. Tools needed: screwdriver, wrench, pliers. Frequently Asked Questions My dryer won't start. Is this the part I need? Yes, this is one of the most common symptoms of a failed door switch. Since this switch tells the control board whether the door is closed, a damaged or malfunctioning switch can prevent the dryer from starting even when the door is fully shut. My dryer door won't close properly. Could this be the same part? Yes, a damaged door switch — often from excessive force when closing the door over time — can cause the door to not latch or close correctly, in addition to preventing the dryer from starting. Is this a difficult repair? It's a straightforward repair for a confident DIYer, requiring a screwdriver, wrench, and pliers, along with some slight disassembly of the dryer's front panel to access the switch. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original switch design and mounting configuration of the door switch originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH44X10288 Washer Lid Lock and Switch Assembly Replaces Part Numbers: WH44X10288, 1974376, AH3496878, EA3496878, AP5270191, PS3496878. 120V, 60Hz, lid lock and switch assembly. Fits select GE laundry center. Description: This Door Latch Lid Lock is a replacement part for select GE washing machine models. It is designed to securely lock the washing machine's lid or door during operation, ensuring safety and preventing water from spilling during the wash cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less