Search results for "washer switches"

XPARTCO 3406107 Dryer Door Switch Replaces WP3406107 The XPARTCO 3406107 is an aftermarket replacement door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. Mounted inside the upper corner of the front panel, this safety switch has a spring-loaded black tab that gets pressed in when the door closes. That contact tells the control board the door is shut, which is required before the dryer will start, and it also powers the interior drum light. Over time the switch's internal contacts wear out or the tab loses spring tension, and the dryer either won't start at all or runs with the door open — a safety condition the switch is specifically designed to prevent. This is a three-wire SPDT (single pole, double throw) switch built to the same dimensions and mounting points as the original, and it's designed to remain compatible with older two-wire harnesses as well. Direct-fit aftermarket replacement, no wiring modifications needed. Quick Answer The XPARTCO 3406107 Dryer Door Switch fixes a dryer that won't start, runs with the door open, or has a dead interior light. Direct-fit replacement for OEM WP3406107. Classic symptom: pressing start does nothing until you push and hold the door shut, or the drum light never comes on. Common Problems This Part Fixes Dryer won't start even though the door is closed Dryer runs with the door open (safety switch failure) Interior drum light doesn't turn on Door doesn't seem to latch or seal properly against the switch tab Drum doesn't spin, or cycle stops intermittently Touchpad or start button appears unresponsive Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, AWP47183, PS11741701 This switch design was updated to a three-wire configuration at some point in its production history (superseding older 3405100/3405101/3406100/3406101 numbers), but the current three-wire version remains compatible with older two-wire harnesses, so it's a safe direct replacement across all of these part numbers. Compatibility This door switch is compatible with a wide range of Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including units across the: Whirlpool/Kenmore Series 60, 70, 80, 90, 500, 600, 700, and 800 dryer lines AED4475TQ1, MEDC400VW0, and numerous additional model numbers Note: This switch has been used across a very wide range of Whirlpool-built dryers (including Kenmore, Maytag, and KitchenAid badged units) spanning many production years, so the list above is only a sample. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket door safety switch for Whirlpool-built dryers Three-wire SPDT design, backward-compatible with two-wire harnesses Controls both the start-permission safety interlock and the interior drum light Resolves no-start, runs-with-door-open, and dead-light symptoms White plastic and metal tab construction, approx. 6.5" length Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number 3406107 OEM Part Number WP3406107 Part Type Dryer Door Safety Switch Condition Aftermarket Replacement Switch Type SPDT (Single Pole, Double Throw) Wire Configuration Three-Wire (Backward-Compatible with Two-Wire Harnesses) Length Approx. 6.5 Inches Color / Material White; Plastic & Metal Construction Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. The switch is mounted inside the upper corner of the front panel, so you'll need to remove the front panel or top panel per your model's service guide to access it. Disconnect the wire connector from the old switch, then remove the mounting screw(s) holding it in place. Install the new switch in the same position, reconnect the wire connector, and reinstall the panel. Before closing everything up, you can test the switch by pressing the black tab — you should feel spring resistance and hear or feel a distinct click. Restore power and confirm the dryer starts normally with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start — is this the part I need? This is one of the most common causes of a dryer that won't start even with the door closed. Try pressing the black tab on the switch by hand — if it feels loose, doesn't click, or offers no resistance, the switch has likely failed and needs replacement. My dryer runs even with the door open — is that dangerous? Yes, this indicates the door safety switch has failed in a way that no longer prevents operation with the door open, which is a safety hazard. Replace the switch promptly and avoid running the dryer with the door open in the meantime. My dryer has a two-wire connector — will this three-wire switch still work? Yes. This switch was redesigned to a three-wire configuration but remains compatible with older two-wire wiring harnesses, so it's a safe direct replacement regardless of which wire configuration your dryer currently has. Does this switch also control the interior light? Yes. This switch serves a dual function — it's the safety interlock that permits the dryer to run only with the door closed, and it also powers the interior drum light when the door is open. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406105 Dryer Door Switch Replaces WP3406105 The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open. This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560. Common Problems This Part Fixes Dryer will not start at all — door switch not completing the circuit when door is closed Dryer starts only when the door is slammed or held firmly closed Dryer continues to run after the door is opened — switch not opening the circuit Drum light not turning on when the door is opened (on models with drum light) Dryer starts intermittently — door switch contact worn and making unreliable contact Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear Door switch visibly cracked, broken, or the actuator button no longer springs back Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Roper dryers Estate dryers Crosley dryers Inglis dryers Admiral dryers Jenn-Air dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L Stainless steel terminals and heat-resistant housing Kit includes switch and 3-wire harness assembly — complete plug-in replacement Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560 Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3406105 OEM Part Number WP3406105 Part Type Dryer Door Switch Assembly (SPDT 3-Wire) Condition Aftermarket Replacement Application Gas and Electric Dryers Switch Type Single Pole, Double Throw (SPDT) Wires 3-wire Voltage 120-240V Frequency 50-60Hz Amperage 11A Horsepower 1/3 HP Switch Body Dimensions 1-3/4" L x 1-5/8" W x 1-1/4" H Harness Length 7-3/4 inches Color Off-White / Black / Gray Material Plastic / Metal (stainless steel terminals) Includes Switch and 3-wire harness assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife. Frequently Asked Questions What does the dryer door switch do? The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit. How do I test the door switch with a multimeter? Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed. What is the difference between 3406105 and 3406104? The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement. Why does this switch have 3 wires when my old switch only had 2? The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WP3406107 Dryer Door Switch The Genuine OEM Whirlpool WP3406107 is a dryer door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. It mounts inside the top of the dryer's front panel, with one end connecting to the wiring harness and the other passing through the panel to make contact with the door. When the door closes, it presses the switch's black tab, which tells the dryer the door is shut so it can run. When the switch wears out, the dryer may not start, may run with the door open, or may lose its interior light. This is the original Whirlpool part, a white, 6.5 inch, three-wire switch. Retailers describe the switch as a regular wear part and rate the repair as really easy, typically 15 to 30 minutes. Quick Answer The Genuine OEM WP3406107 Door Switch fixes a Whirlpool, Kenmore, Maytag, or KitchenAid dryer that won't start, runs with the door open, has a light that doesn't work, or has a door that won't close properly. Quick test: with the dryer unplugged, press the switch's black tab. If it has no resistance and doesn't click, the switch likely needs replacing. Common Problems This Part Fixes Dryer won't start Dryer runs with the door open Interior light doesn't work Door won't close or latch properly against the switch Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, W10569603, 3405100, 3405101, 3406100, 3406101, 528948, 11259-65, 11288-80, WP3406107VP, AP6008561, AWP47183, EAP11741701, PD00002378, PS11741701 These numbers come from retailer cross-reference lists and span several generations of Whirlpool's own numbering for this switch. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This door switch is listed for Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including these examples: Kenmore 11060372710, 11060522900, 11060702990, 11060802990 Kenmore 11061202010, 11061262311, 11061802000 Whirlpool EED4400WQ Note: The models above are a small sample of a longer list, not a full list. This is a three-wire switch that replaces the two-wire switch found on many models, so compare it to your old switch, and contact our support team with your model number to verify fit before ordering. Key Features Genuine OEM Whirlpool dryer door switch, not an aftermarket equivalent Three-wire design; replaces the two-wire switch on many models White, 6.5 inch switch with a spring-loaded black tab Resolves no-start, runs-with-door-open, and light problems caused by a worn switch Typically a 15 to 30 minute repair Product Specifications Part Number WP3406107 OEM Part Number WP3406107 Part Type Dryer Door Switch Condition Genuine OEM Manufacturer Whirlpool Length 6.5 Inches Color White Wire Configuration Three-Wire Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as cabinet edges can be sharp. The switch is mounted inside the top of the front panel, so follow your model's service guide to remove the panel needed to reach it. Note how the wiring connector is attached, disconnect it, and remove the old switch. Fit the new switch in the same position, reconnect the wiring, and reassemble. Restore power and confirm the dryer starts with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start. Is this the part I need? A worn door switch is a common cause. With the dryer unplugged, press the switch's black tab. If there is no resistance and no click, the switch likely needs replacing. My dryer runs with the door open. Is that a problem? Yes. The door switch is a safety part that stops the dryer from running when the door is open. If the dryer runs with the door open, replace the switch promptly. My dryer has a two-wire switch. Will this three-wire switch work? Retailers list this three-wire switch as the replacement for the two-wire switch found on many models. Compare it to your old switch and your wiring, or contact our support team with your model number, before ordering. Will this fit my dryer? It is listed for many Whirlpool, Kenmore, Maytag, and KitchenAid dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC64-00828B Dryer Door Switch The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open. This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers. Common Problems This Part Fixes Dryer not starting even though the door is closed Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently Error codes dC, dF, dE, or d0 displayed on models with digital displays Dryer continuing to run with the door open (unsafe failure mode — replace immediately) Interior dryer light not turning on when the door is opened Door switch button visibly broken, stuck, or not making the expected click when pressed Multimeter test shows the switch fails to change state when actuated Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including: Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related) Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related) Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related) Samsung dryers — DV5 series (DV50K7500EW and related) Samsung dryers — DVE series (DVE60M9900W and related electric models) Samsung dryers — DVG series (DVG45N5300V and related gas models) Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch that detects whether the dryer door is closed — required for the dryer to start and run Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing Durable plastic housing with metal contacts — withstands frequent door open/close cycles Resolves Samsung door-related error codes including dC, dF, dE, and d0 Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436 Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC64-00828B Also Replaces DC64-00828A (prior version) Part Type Dryer Door Switch (Door Jamb Switch) Condition Aftermarket Replacement Application Electric and Gas Dryers (Samsung platform) Dimensions Approximately 1.73"L x 1.73"W x 0.47"H Color White Material Plastic / Metal Error Codes Resolved dC, dF, dE, d0 (door-related) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What do error codes dC, dF, dE, and d0 mean on Samsung dryers? These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage. My dryer is running with the door open — what should I do? A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer. What is the difference between DC64-00828B and DC64-00828A? These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing. My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch? Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10420741 Genuine OEM Dryer Push To Start Switch - Compatible with Whirlpool, Kenmore, Maytag Product Description Restore your dryer’s functionality with the WPW10420741 Genuine OEM Dryer Push To Start Switch. This Whirlpool-manufactured switch, featuring screw terminals, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It initiates the drying cycle with a simple button press, addressing issues like the dryer not starting or starting inconsistently. Built for durability, it ensures reliable performance under frequent use. Note: Includes (1) push to start switch. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WPW10420741, W10420741, PD00008413, EAP3632880, AP6021228, PS11754549. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WET4027HW0, WET4027HW1, WET4027HW2, YWET4027HW0, 7MWGT4027HW0 Kenmore: 110.97591420, 110.97591220, 110.97592420 Maytag: YNED4655EW, YIED4671EW Roper: RED4516FW0, RED4640YQ0, RED4640YQ1, RED4645EW0 Crosley: VDEW6511RW0, VED6505GW0 Amana: NED4655EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana, and other dryers. 🔧 Specifications: Genuine OEM Whirlpool push to start switch with screw terminals, 120V, 2-terminal configuration. 💪 Reliable Performance: Initiates drying cycle with a button press, ensuring consistent operation. 🛠️ Easy Installation: Requires a screwdriver; typically installed in 10–20 minutes. 🛡️ Effective Fixes: Resolves dryer not starting or inconsistent starting issues. Product Specification Part Number: WPW10420741 Component Type: Dryer push to start switch Material: Plastic and brass/stainless steel Electrical Specs: 120V, 2-terminal, normally open, single-pole single-throw (SPST) Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

Genuine OEM WPW10446920 Dryer Push-To-Start Switch The Genuine OEM WPW10446920 is a factory-original push-to-start switch manufactured by Whirlpool for use in Whirlpool, Maytag, Amana, Kenmore, Inglis, and other Whirlpool-built dryers that use a momentary push-button start control rather than a pull/rotary start knob. Pressing and releasing the button sends a signal to the timer or control board that begins the drying cycle; the switch itself does not stay latched, so the control electronics — not the switch — keep the dryer running after you let go. When this switch fails, the dryer typically has power (the display and drum lights, if equipped, still work) but pressing Start does nothing, or the button feels mushy and requires several presses to register. As the genuine Whirlpool part, it ships with the exact factory-specified contacts, housing, and three-terminal wiring connector used on original production, so there's no fit or function guesswork. It directly replaces W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857. Installs in 15–30 minutes with basic hand tools. Quick Answer The Genuine OEM WPW10446920 Dryer Push-To-Start Switch fixes Whirlpool, Maytag, Amana, Kenmore, and Inglis dryers that won't start when the Start button is pressed, even though the dryer otherwise has power. This is the factory-original Whirlpool switch — not an aftermarket equivalent — with a 3-terminal wiring connector. Replaces W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857. Classic symptom: display and lights work, but pressing Start produces no response at all. Common Problems This Part Fixes Dryer won't start when the Start button is pressed Start button feels loose, mushy, or requires multiple presses to register Dryer has power (lights/display work) but the motor never engages Intermittent starting — sometimes works, sometimes doesn't Audible click from the button with no response from the dryer Start switch visibly cracked, stuck, or not returning after being pressed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This push-to-start switch directly replaces the following OEM and cross-reference part numbers: WPW10446920, W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This push-to-start switch is compatible with select Whirlpool-built dryers from the following brands: Whirlpool dryers (including 7MWED1650EQ0, 7MWGD1750EQ0, 7MWGD1850EI0 and related models) Maytag dryers (select Whirlpool-built models, including MED4005SW0, MGD4005SW0) Amana dryers (select models, including NED4700YQ0, NGD4700YQ1) Kenmore dryers (select Whirlpool-built models, including 11062332511, 11072332510) Inglis, KitchenAid, Jenn-Air, Magic Chef, and Admiral dryers (select Whirlpool-built models) Note: This switch is specific to dryers with a push-to-start button. It is not used on models with a rotary or pull-to-start knob — those use a different start switch design. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM push-to-start switch — factory-original fit, form, and function Resolves "won't start," "mushy button," and "intermittent start" symptoms caused by switch failure Momentary contact design — signals the timer/control board to begin the cycle 3-terminal wiring connector matching original factory harness Direct-fit mounting to the original control panel opening Replaces W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857 Compatible with Whirlpool, Maytag, Amana, Kenmore, and Inglis dryers Genuine OEM part — factory-specified materials and electrical rating Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number WPW10446920 OEM Part Number WPW10446920 Part Type Dryer Push-To-Start Switch Condition Genuine OEM Replacement Switch Type Momentary Push Button Terminals 3-terminal wiring connector Application Push-To-Start Dryer Control Panels Compatible Brands Whirlpool, Maytag, Amana, Kenmore, Inglis Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Access the control panel — on most models this means removing a few screws along the top or rear of the console, or releasing spring clips, and tilting or lifting the panel to expose the back of the start switch. Photograph the wiring before disconnecting. Unplug the 3-terminal wiring connector from the old switch — note the connector orientation. Depress the retaining tabs or remove the mounting screw(s) holding the switch in the control panel and push it out from the back. Install the new WPW10446920 switch into the same opening until it snaps or seats into place. Reconnect the wiring connector, matching your photos. Reassemble the control panel and secure it with its screws or clips. Plug the dryer back in and test by pressing Start — confirm the dryer begins its cycle. Tools needed: Phillips screwdriver, putty knife or flat-blade screwdriver (for spring clips, if applicable). Frequently Asked Questions My dryer has power but won't start when I press the button — is this the part? This is the classic symptom of a failed push-to-start switch. If the display and any lights still work but pressing Start produces no response — not even a click or hum from the motor — the start switch is the most common cause. If you do hear a hum or click but the drum still doesn't turn, also check the thermal fuse and cycling thermostat, since a tripped thermal fuse can sometimes present with similar no-start symptoms. Will this fit my dryer? WPW10446920 and its cross-reference numbers fit a range of Whirlpool-built dryers across several brands, but only models with a push-to-start button — not a rotary or pull-to-start knob. Confirm fit using your dryer's exact model number before ordering, since the two start mechanisms are not interchangeable. Is this a genuine Whirlpool part or an aftermarket equivalent? This is the genuine, factory-original Whirlpool part — not an aftermarket equivalent. It ships with the same contacts, housing, and 3-terminal connector used in original production, so there's no guesswork on fit, feel, or electrical rating. Do I need any special tools to install this? No — just a Phillips screwdriver and, on some models, a putty knife or flat-blade screwdriver to release the control panel's spring clips. No soldering or wire splicing is required; the switch connects via its original 3-terminal plug. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine Whirlpool OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH03X36897 Washer Genuine OEM Mode Shifter Actuator – Compatible with GE & Hotpoint Washers Product Description Restore proper wash and spin operation with the WH03X36897 Washer Genuine OEM Mode Shifter Actuator. This factory-approved component shifts the washer between agitation and spin modes during the wash cycle. A failing mode shifter can cause the washer to agitate but not spin, spin improperly, make clicking noises, or display cycle errors. Replacing it with this Genuine OEM actuator ensures precise shifting, reliable performance, and correct cycle operation. Replaces Part Numbers WH03X36897, WH18X27186, AP7225424, PD00087767, EAP17626543, PS17626543 Compatibility This Genuine OEM mode shifter actuator fits select GE and Hotpoint top-load washers. Example compatible models include (but are not limited to):GE GTW335ASN1WW, GTW465ASN2WW, GTW485ASJ1WSHotpoint HTW240ASK6WS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and dependable operation 🔄 Accurate Mode Shifting – Properly switches between wash and spin cycles 🔇 Quiet, Smooth Operation – Reduces clicking or erratic shifting noises 💪 OEM-Grade Durability – Designed for long service life under repeated cycles 🛡️ Fixes Common Issues – Solves no-spin, improper agitation, or cycle errors 📐 Product Specification Part Number: WH03X36897 Component Type: Washer Mode Shifter Actuator Voltage: 120V AC Mounting: Direct-fit installation on transmission assembly Function: Controls agitation-to-spin shifting Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Steps: Disconnect power and tilt the washer back for bottom access. Locate the mode shifter actuator near the transmission. Disconnect the wiring harness and remove mounting screws. Install the new WH03X36897 actuator and secure it in place. Reconnect wiring, return washer upright, and restore power. Run a test cycle to confirm proper shifting. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore correct washer cycle operation — Add to Cart Now for a factory-quality repair!

Read more less

XPARTCO W10195039 Dishwasher Float Switch The XPARTCO W10195039 is an aftermarket replacement float switch for Whirlpool-built dishwashers sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana and related brand names. The float switch is the safety device that shuts off the water fill valve if the water level gets too high before the timed fill cycle ends, so a failed float can mean overfilling or a dishwasher that won't fill properly. This is a direct-fit aftermarket replacement for the original Whirlpool float switch, which is sold as W10195039 and WPW10195039. Float problems can look like valve or control problems, so check the float for a stuck or damaged action before replacing it. Quick Answer The XPARTCO W10195039 Float Switch fixes a Whirlpool-built dishwasher that overfills, leaks from too much water, or won't fill because the float is stuck, damaged, or no longer switching. It is also listed as WPW10195039. Classic symptom: water keeps filling past the normal level, or the dishwasher won't fill and the float looks stuck or cracked. Common Problems This Part Fixes Dishwasher overfills or the water level gets too high Water leaking from too much water in the tub Dishwasher won't fill because the float switch is stuck or failed Float is cracked, broken, or doesn't move freely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This float switch directly replaces the following part numbers: WPW10195039, W10195039, W10734532, 1872053, MS10-06, AP6016738, AWP49215, EAP11750031, PD00002753, PS11750031 W10195039 is the older Whirlpool number and WPW10195039 is its current replacement. W10734532 comes from a single retailer cross-reference, so confirm against your dishwasher's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This float switch is listed for Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana, and Inglis dishwashers, including these examples: Kenmore 66513979K017, 66515049K111, 66513964K017, 66512776K310 ADB1100AWB0, CDBW4400SB0, KUDC10FBBL0, KUDS30FXSS0, MDB4709PAB0 Note: The models above are a sample of a much longer list, not a full list. A dishwasher that won't fill can also be caused by the inlet valve, so test the float and valve before ordering. Confirm your model number against your parts diagram, or contact our support team to verify fit. Key Features Direct-fit aftermarket float switch for Whirlpool-built dishwashers Shuts off the fill valve if the water level gets too high Replaces both W10195039 and WPW10195039 Fits Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air and related brands Product Specifications Part Number W10195039 OEM Part Number W10195039, WPW10195039 Part Type Dishwasher Float Switch Condition Aftermarket Replacement Application Whirlpool-Built Dishwashers Installation Notes ⚠️ Disconnect Power and Shut Off the Water Unplug the dishwasher or switch off its circuit breaker, and turn off the water supply before beginning. Wear work gloves to protect your hands. Follow your model's service guide to reach the float switch, and note the position of each wire connector before disconnecting it. Install the new float switch in the same position, reconnect the wires, and check that the float moves freely before closing the dishwasher. Run a cycle and check for leaks. Frequently Asked Questions What does the float switch do? It shuts off the water fill valve if the water level gets too high before the timed fill cycle ends. It is a safety device that helps prevent overflow. My dishwasher still won't fill. Will this fix it? Only if the float is the cause. A dishwasher that won't fill can also have a bad inlet valve, a clogged inlet screen, or a control problem. Check that the float moves freely and test the valve first. Is W10195039 the same as WPW10195039? Yes. W10195039 is the older Whirlpool number and WPW10195039 is its replacement. This float switch covers both. Will this fit my dishwasher? It is listed for many Whirlpool-built dishwashers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XPARTCO WH03X30517 Washer Shift Actuator The XPARTCO WH03X30517 is an aftermarket replacement shift actuator (mode shifter) for GE top-load washers, and also fits select Hotpoint and Kenmore models. Mounted at the bottom of the washer, this actuator changes the function of the washer's motor between agitation and spin cycles, effectively managing the conversion from agitation to high-speed rotation that removes moisture from clothing at the end of the wash. Made mostly of plastic, with two mounting holes and a single wire harness connection. Over time, the actuator's internal motor can burn out or fail electrically. Symptoms of a failing shift actuator include the washer failing to switch between agitation and spin modes, the washer not spinning or agitating at all, abnormal noise or grinding during the cycle, or clothes coming out still soggy after a completed wash. It directly replaces WH03X30517, WH05X24435, WH05X25036, 290D1056G001, 4588015, 4961069, AP7014559, AGE25894, PD00068062, EAP16554752, PS16554752. Quick Answer The XPARTCO WH03X30517 Washer Shift Actuator fixes GE, Hotpoint, and Kenmore top-load washers that won't switch between agitation and spin, won't spin or agitate at all, or leave clothes still soggy after a wash. Sold individually. Replaces WH03X30517, WH05X24435, WH05X25036, 290D1056G001, 4588015, 4961069, AP7014559, AGE25894, PD00068062, EAP16554752, PS16554752. If your washer agitates and spins fine individually but still won't switch between the two modes after replacing this actuator, the underlying cause may lie elsewhere — one customer found this exact residual symptom after installing this part. Common Problems This Part Fixes Washer won't switch between agitation and spin modes Washer not spinning or agitating at all Abnormal noise or grinding during the wash cycle Clothes still soggy after a completed wash cycle No clicking sound heard when the washer attempts to change modes Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer shift actuator directly replaces the following OEM and cross-reference part numbers: WH03X30517, WH05X24435, WH05X25036, 290D1056G001, 4588015, 4961069, AP7014559, AGE25894, PD00068062, EAP16554752, PS16554752 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shift actuator is compatible with select GE top-load washers, and also fits select Hotpoint and Kenmore washers built on the GE platform, including model numbers such as: GTW680BSJ0WS, GTW680BSJ1WS, GTW680BSJ2WS, GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS, GTW680BSJ7WS GTW220ACK1WW, GTW220ACK2WW, GTW220ACK3WW, GTW220ACK7WW GTW540ASP0WS, GTW540ASP1WS, GTW465ASN2WW, GTW500ASN1WS, GTW685BSL2WS YTW4514SN0WS, YTW4514SN1WS, YTW4514PN0DG, YTW4514PN1DG GTW335ASN0WW, GTW335ASN2WW, GTW460AMJ2WW, GTW750CPL0DG GTW490ACJ1WW, GTW490ACJ1WS, GTW490ACJ6WW, GTW490ACJ6WS HTW200ASK0WW, HTW200ASK1WW, HTW200ASK2WW, HTW200ASK3WW, HTW200ASK4WW HTW240ASK0WS, HTW240ASK1WS, HTW240ASK2WS, HTW240ASK3WS, HTW240ASK4WS, HTW240ASK5WS, HTW240ASK6WS Note: This is the standalone shift actuator only, sold individually. A related but separate combined kit exists that also includes a shift clutch (WH05X24185); if you also need the clutch, order it separately. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement shift actuator (mode shifter) — switches the motor between agitation and spin Resolves "won't switch modes," "won't spin or agitate," and "clothes still soggy" symptoms caused by actuator failure Mostly plastic construction, two mounting holes, single wire harness Direct drop-in replacement matching the original mounting Replaces WH03X30517, WH05X24435, WH05X25036, 290D1056G001, 4588015, 4961069, AP7014559, AGE25894, PD00068062, EAP16554752, PS16554752 Compatible with GE, Hotpoint, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Sold individually Typical repair takes 15 to 30 minutes Product Specifications Part Number XPWH03X30517 OEM Part Number WH03X30517 Part Type Washer Shift Actuator (Mode Shifter) Condition Aftermarket Replacement Material Plastic Mounting Two screw holes Wiring Single wire harness Related Part WH05X24185 shift clutch (sold separately) Repair Difficulty Easy to Moderate — 15 to 30 minutes Quantity 1 shift actuator (sold individually) Compatible Brands GE, Hotpoint, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Laying The Washer On Its Side Makes Access Easier Disconnect power at the outlet before beginning. Wear work gloves. This repair typically requires tipping or laying the washer on its side to access the bottom of the machine, where the shift actuator is mounted. Lay the washer down carefully, protecting the floor and the washer's exterior. Locate the shifter connector and unplug it, then remove the two screws holding the actuator in place. Take out the old actuator. Install the new WH03X30517 in the same position, securing it with the two mounting screws, and reconnect the wire harness connector fully. Stand the washer back upright. Restore power and run a test cycle to confirm the washer switches correctly between agitation and spin, listening for a clicking sound as it changes modes. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My washer won't switch from wash to spin, but it will spin if I catch it there. Is this the part I need? Yes, this is a well-documented symptom of a failing shift actuator. One customer described their machine not going to wash mode with no clicking sound heard when the mode should change, which is a classic sign this part has failed. They accessed the actuator by laying the machine on its side, then unplugged the shifter connector and removed two screws to complete the swap. I replaced this part but my washer still won't switch from wash to spin. What's going on? This is a fair question, and it's worth knowing that replacing this actuator doesn't always resolve every mode-switching problem on its own. One customer replaced the mode shifter, cleared all codes, and confirmed the washer agitated and spun fine individually, but it still wouldn't switch between the two modes — suggesting a different or additional component may have been involved in their specific case. If you're still having trouble after installing this part, further diagnosis of the transmission or related components may be needed. Does this come with the clutch too? No, this listing is for the shift actuator only, sold individually. A related shift clutch, WH05X24185, is a separate part — if your repair requires replacing both, you'll need to order the clutch separately. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the mounting, wiring, and switching function of the original WH03X30517 shift actuator used in compatible GE, Hotpoint, and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10352973 Washer Genuine Dispenser Actuator Dispenser Drawer Switch Actuator for Washer Replaces Part Numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574. ✅ Product Description: Restore proper detergent dispensing with this genuine OEM WPW10352973 washer dispenser actuator. Designed to control the flow of detergent and fabric softener into your wash cycle, this part is a direct replacement for worn or non-functioning actuators in many Whirlpool, Maytag, Amana, Kenmore, and Crosley top-load washing machines. Part Features: Genuine OEM quality – built to factory specs Replaces part numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574. Controls dispenser drawer movement for proper release timing Easy to install with basic tools Fixes the following symptoms: Dispenser drawer not opening Detergent or softener not dispensing Error codes related to actuator failure Inconsistent or incomplete wash cycles Compatible with:Many models from Whirlpool, Maytag, Kenmore, Amana, and more.(Check model number before ordering or contact us for fitment help.) ✅ Why Buy from Parts-O-Matic? Guaranteed OEM-quality parts Always Fast and Free U.S. shipping Competitive pricing Expert support for part compatibility 🛒 Get your washer working like new – order the WPW10352973 Dispenser Actuator now at Parts-O-Matic.com, and enjoy fast, free shipping with no minimum.

Read more less