XPARTCO W10599356 Washer Water Valve
The XPARTCO W10599356 is an aftermarket replacement water inlet valve for Whirlpool-built front-load washers, including full-size and compact models. This valve sits at the back of the washer where the hot and cold water supply hoses connect, and it's the gatekeeper for every drop of water that enters the drum. When the control calls for water, it energizes the valve's solenoid coils to open the hot side, the cold side, or both together, and closes them again once the correct fill level is reached. A valve that won't open leaves you with no fill at all; a valve that won't fully close can let water trickle or flow into the drum even when the cycle isn't calling for it.
Over time, mineral deposits and sediment from the water supply can build up inside the valve body and prevent it from sealing fully, the internal solenoid coil can burn out electrically, and the rubber diaphragm or seal inside can simply wear out with age. A failing valve on this platform commonly triggers an F8 E1 or similar fill-related error code, since the control expects water to reach the correct level within a set time and flags it when that doesn't happen. It directly replaces AP5692067, 3023192, PS8689091, and W10509710.
Quick Answer
The XPARTCO W10599356 Washer Water Valve fixes Whirlpool-built front-load washers that won't fill, fill slowly, overfill, leak water into the drum when the cycle isn't running, or throw an F8 E1 or similar fill-related error code. Solenoid-actuated water inlet valve for the hot and cold supply connections. Replaces AP5692067, 3023192, PS8689091, W10509710. Consider replacing the fill hoses at the same time — they wear on a similar schedule and share the same access point.
Common Problems This Part Fixes
Washer won't fill with water at the start of the cycle
Washer fills much more slowly than normal
Washer overfills or takes on more water than the cycle calls for
Water trickling or leaking into the drum when the washer is off or between cycles
F8 E1 or similar fill-related error code displayed on the control panel
Cycle stalling at the fill step and never advancing to wash
No hot water, no cold water, or neither reaching the drum
Water pooling underneath or behind the washer near the supply connections
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
W10599356, W10509710, AP5692067, 3023192, 33090084, C-022/16-B21, EAP8689091, AWP41165, PD00022876, PS8689091
W10509710 was the immediately preceding number that Whirlpool revised to W10599356. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including:
Whirlpool front-load washers — WFW series
Maytag front-load washers — MHW series (select Whirlpool-built models)
KitchenAid, Jenn-Air, and Amana front-load washers (select models)
Magic Chef, Admiral, and Norge front-load washers (select models)
Roper and Kenmore front-load washers (select Whirlpool-built models)
Verified model numbers include: WFW70HEBW0, WFW70HEBW1, WFW70HEBW2, WFW72HEDW0, WFW7590FW0, WFW75HEFW0, WFW80HEBC0, WFW80HEBC1, WFW80HEBC2, WFW80HEBW0, WFW80HEBW1, WFW80HEBW2, WFW81HEDW0, MHW3000BG0, MHW3000BG1, MHW3000BG2, MHW3000BW0, MHW3000BW1, MHW3000BW2, MHW3100DW0, MHW4000BW1, MHW4000BW2, MHW4100DW0, MHW5100DC0, MHW5100DW0, NFW5700BW0, NFW5700BW1, NFW5800DW0, 7MWFW72HEDW0, 7MWFW80HEBW0, and 7MWFW81HEDW0.
Note: This valve fits Whirlpool's front-load washer platform. It is not intended for top-load washers, which use a different valve design and mounting configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement solenoid-actuated water inlet valve for hot and cold supply connections
Resolves "won't fill," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure
Commonly resolves F8 E1 and similar fill-related error codes
Direct drop-in replacement for the superseded W10509710 valve
Replaces AP5692067, 3023192, PS8689091, and W10509710
Compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair — typically completed in 30 to 60 minutes
Product Specifications
Part Number
W10599356
OEM Part Number
W10599356 (formerly W10509710)
Part Type
Washer Water Inlet Valve
Condition
Aftermarket Replacement
Application
Front-Load Washers (Whirlpool-Built)
Actuation
Solenoid-operated
Connections
Hot and cold water supply inlets
Supersedes
W10509710
Repair Difficulty
Easy to Moderate — 30 to 60 minutes
Quantity
1 valve
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the hot and cold water supply lines from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Use a 1/4" nut driver or socket to remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve from inside the cabinet. Photograph the wiring connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove the mounting screw or bracket (often a T-20 Torx screw), and pull the valve free from its mounting position. Install the new W10599356 in the same orientation, secure the mounting screw, and reconnect the electrical connector fully. Reattach the hot and cold water supply lines to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. While everything is accessible, consider replacing the fill hoses as well, since they wear on a similar schedule. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves.
Frequently Asked Questions
My washer shows an F8 E1 error. Does that mean the valve is definitely bad?
It's a strong indicator, but check the basics first. F8 E1 and similar fill-related codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm both hot and cold supply valves at the wall are fully open, check the inlet screens inside the valve ports for sediment or debris, and make sure the fill hoses aren't kinked. If those check out and the washer still won't fill properly, the inlet valve itself is the likely cause.
Water keeps trickling into the drum even when the washer is off. Is that the valve?
Yes, this is one of the classic symptoms of a valve that isn't sealing fully closed. Mineral deposits, sediment, or a worn internal diaphragm can prevent the valve from shutting off completely, letting a slow trickle of water continue into the drum between cycles. This can eventually lead to an overfill or water pooling at the front of the washer, so it's worth addressing promptly rather than waiting.
Only hot or only cold water isn't coming in. Do I need to replace the whole valve?
Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair.
Should I replace the fill hoses while I'm in there?
It's a good idea. The fill hoses connect right at the same point you'll already have exposed, wear on a similar timeline as the valve, and are a common source of slow leaks that get blamed on the valve. Since you're already accessing this area, replacing hoses that show any cracking, bulging, or stiffness saves you from repeating the disassembly later.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the solenoid design, flow rate, and mounting configuration of the original W10599356 / W10509710 valve used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
EXPW79SC (4 Pack) Washing Machine Fill Hose Gasket with Screen
4 Pack
compatible with 5/ 8 inch washing machine and 3/4 inch garden hose
Fine Screen
the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively
XPARTCO DC66-00777A Washer Pulsator Cap – Compatible with Samsung Washers
Product Description
Keep your washer operating smoothly with the XPARTCO DC66-00777A Washer Pulsator Cap. This high-quality aftermarket replacement covers the central pulsator bolt, preventing water, detergent, and debris from entering the washer hub. A cracked or missing cap can lead to corrosion, noise, or imbalance during spin cycles. Replacing it with this durable XPARTCO cap restores a secure seal and helps maintain optimal washing performance.
Replaces Part Numbers
DC66-00777A, PD00025125, EAP8753312, AP5788799, 3282678, PS8753312.
Compatibility
This replacement pulsator cap fits select Samsung top-load washers.
Example compatible models include (but are not limited to): Samsung WA400PJHDWR/AA, WA422PRHDWR/AA, and WA45H7000AW/A2.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and performance for Samsung washers
💧 Protective Seal – Keeps water and detergent away from the pulsator bolt area
💰 Cost-Effective Solution – Durable and affordable alternative to OEM caps
🛠️ Simple Installation – No tools required; snaps directly into place
🛡️ Fixes Common Issues – Replaces missing or damaged caps to prevent rust and noise
📐 Product Specification
Part Number: DC66-00777A
Component Type: Washer Pulsator (Washplate) Cap
Material: High-strength molded plastic
Color: Gray or silver finish (varies by batch)
Mounting: Snap-fit installation on top of pulsator bolt
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Always unplug the washer before performing any maintenance to avoid electrical shock.
Steps:
Open the washer lid and locate the center of the pulsator (washplate).
Remove any remaining parts of the old or damaged cap.
Align the new XPARTCO DC66-00777A cap with the pulsator hub opening.
Press firmly until it clicks into place.
Verify the cap is secure before running a wash cycle.
⏱️ Time Required: Less than 5 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Protect your washer from wear and debris — Add to Cart Now for a quick, reliable fix!
W11230103 Dishwasher Sump Pump and Motor
Replaces Part Numbers: W11230103, W10620220, 4591207, AP6329759, PS12349660.
Description: This Pump & Motor is an OEM part for Whirlpool dishwasher models. It serves as the heart of the wash system by providing water circulation and spray throughout all cycles. The pump circulates water mixed with detergent to clean dishes effectively.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 5220FR2008C Washer Water Valve
The XPARTCO 5220FR2008C is an aftermarket replacement water inlet and dispenser valve assembly for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's water source and to the washer's solenoid wiring, controlling exactly how much water enters the tub and ensuring the correct fill level for each cycle. The assembly has 1 inlet and 4 outlets.
Rated 120V, 60Hz. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer continuing to fill even after it should be full, filling slowly, overfilling, or leaking water into the drum when the washer is off. On some LG models, this can also trigger an FE error code specifically tied to the fill process. It directly replaces 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429
Quick Answer
The XPARTCO 5220FR2008C Washer Water Valve fixes LG and select Kenmore front-load washers that keep filling past full, fill slowly, overfill, or leak water into the drum when off — sometimes accompanied by an FE error code. 120V, 60Hz, 1 inlet, 4 outlets. Replaces 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429. Some LG steam washers use this valve alongside a separate hot water valve — if only one side is failing, you may only need to replace the specific valve at fault rather than the whole group.
Common Problems This Part Fixes
Washer continues filling with water even after it should be full
Washer filling slowly
Washer overfilling
Water leaking into the drum when the washer is turned off
FE error code displayed during the fill portion of the cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform.
Note: LG uses several visually similar water valves across its washer lineup, including 5220FR2006H and 5221ER1003S. This part is also closely related to our 5220FR2008C cold water inlet valve listing — some model listings note that either may fit depending on the exact production run, but they are separate part numbers. Always confirm your exact part number — comparing your old valve's printed number and photo against the listing is the most reliable way to avoid ordering a similar-looking but incorrect valve. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement water inlet and dispenser valve assembly
Resolves "won't stop filling," "fills slowly," "overfills," "leaks when off," and "FE error code" symptoms
1 inlet, 4 outlets
Rated 120V, 60Hz
Sold individually
Direct drop-in replacement — matches the original mounting and hose connections
Replaces 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429
Compatible with LG and select Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XP5220FR2008C
OEM Part Number
5220FR2008C
Part Type
Washer Water Inlet & Dispenser Valve Assembly
Condition
Aftermarket Replacement
Application
Front-Load Washers
Voltage
120V
Frequency
60 Hz
Inlets / Outlets
1 inlet, 4 outlets
Weight
Approx. 0.60 lbs
Package Dimensions
5.12" x 4.69" x 3.98"
Repair Difficulty
Easy to Moderate
Quantity
1 valve (sold individually)
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access on most LG front-load washers requires removing the top cover to reach the water valve assembly and its electrical connections and hoses. On models with multiple valves (some LG steam washers use one separate hot water valve plus a group of cold water valves), identify specifically which valve is failing before removing anything — check your old valve's printed part number and compare it against a reference photo, since several LG valves look very similar. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and hose from the failing valve, remove its mounting screws, and pull it free. Install the new 5220FR2008C in the same position, reconnect the hose and electrical connector fully, and secure the mounting screws. Restore the water supply and power, then run a full test cycle to confirm correct fill behavior with no leaking or error codes. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
My washer shows an FE error code. Is this the valve I need?
Possibly. One customer reported an FE error appearing while the machine was still "filling," which pointed to one of the hot or cold water valves not working correctly. If your FE error consistently appears during the fill portion of the cycle, this valve is a reasonable place to start troubleshooting.
My washer has more than one water valve. Do I need to replace all of them?
Not necessarily. Some LG steam washers use a separate hot water valve plus a group of valves fed from the cold water main, and it's common for only one specific valve in that group to actually be bad. One customer confirmed this exact setup, testing and replacing only the single failing valve rather than the entire group, which resolved their issue.
How do I make sure I'm ordering the correct valve, since several look similar?
Check the part number printed directly on your old valve and compare it, along with a photo if available, against the listing before ordering. One customer specifically noted that several LG valves looked alike, and having a clear reference photo was what let them positively identify the correct replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the solenoid design, inlet/outlet configuration, and electrical rating of the original 5220FR2008C valve used in compatible LG and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly
The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises.
This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump).
Quick Answer
The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ.
Common Problems This Part Fixes
Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms
Weak water pressure at the spray arms — impeller worn or motor failing
Loud droning noise that gets louder over time — worn motor bearings
Grinding or unusual noise during operation
Water retention/pooling in the bottom of the tub
Leaks from the pump housing — seal breakdown
Motor humming but spray arms barely turning
Reduced cleaning performance overall
Motor not running at all — failed pump motor windings
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers:
W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783
W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This circulation pump motor assembly is compatible with select dishwashers from the following brands:
Whirlpool dishwashers — select models (verify with your parts diagram)
KitchenAid dishwashers — select models
Maytag dishwashers — select models
Jenn-Air dishwashers — select models
Amana dishwashers — select models
Magic Chef dishwashers — select models
Admiral dishwashers — select models
Norge dishwashers — select models
Roper dishwashers — select models
Kenmore / Sears dishwashers — select Whirlpool-built models
Ikea dishwashers — select Whirlpool-built models
This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing
Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure
Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns
Current OEM production part — directly supersedes W11122133
Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317
Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine
Drain pump is not included — your existing drain pump transfers to the new assembly
Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers
DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
W11414076
Supersedes
W11122133
Part Type
Dishwasher Circulation Pump & Motor Assembly
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Function
Delivers water to the spray arms for washing and rinsing
Motor Attachment
Separates from pump case with 3 Torx screws
Drain Pump
Not included — transfer your existing drain pump
Location
Bottom of dishwasher (access by laying unit on its back)
Compatible Brands
Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves.
Frequently Asked Questions
The motor runs but water barely reaches the spray arms — do I definitely need a new pump?
Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try.
My dishwasher motor is loud and getting louder — is that the pump?
Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing.
Does this come with the drain pump?
No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub.
What's the difference between W11414076 and W11122133?
These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11305308 Dishwasher Genuine Whirlpool Control Board
Control Board
Main electronic control board.
Fits Specific Whirlpool Dishwasher Models.
Replaces Part Numbers:W11305308, W11131683, W10918994, W11170192, W11227807, AP6832578, PS12704681.
XPARTCO WH01X20826 Washing Machine Shock Absorber
The XPARTCO WH01X20826 is an aftermarket replacement shock absorber (damper) for GE front-load washers. The wash tub inside a front-load washer hangs suspended inside the cabinet, and a set of these shock absorbers is what controls that movement — dampening the tub's vibration and motion during spin so it doesn't bang against the cabinet or shake the whole machine. These washers typically use four shock absorbers working together around the tub, and this listing is for a single individual shock absorber.
Over time the internal damping material in these shocks wears out, or the shock can physically separate from its mounting point — something that can also happen if the washer is moved or shifted without the tub properly secured first. Because all four shocks on a given washer are typically the same age and under the same stress, if one has failed the others are often not far behind — many technicians recommend ordering four of this same part and replacing the full set together as a preventative measure. A worn or detached shock absorber produces a very recognizable symptom: excessive vibration, shaking, or banging noise during the spin cycle, sometimes strong enough that the washer visibly moves or "walks" across the floor. It directly replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130.
Quick Answer
The XPARTCO WH01X20826 Washing Machine Shock Absorber fixes GE front-load washers (and select Hotpoint, Haier, Monogram, Café, and Kenmore models built on the GE platform) that vibrate, shake, or bang excessively during spin, or seem to "walk" across the floor. Sold as a single individual shock absorber. Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. These washers use four shock absorbers total — if one has failed, order four of this part to replace the full set, since they wear on the same schedule.
Common Problems This Part Fixes
Excessive vibration or shaking during the spin cycle
Loud banging or knocking noise from inside the cabinet during spin
Washer that seems to "walk" or move across the floor during operation
Tub striking the cabinet frame or nearby panels
Shock absorber that has visibly separated or detached from its mounting point
Noise or vibration that started or worsened after the washer was moved or relocated
Visible wear, cracking, or looseness in the shock absorber material
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washing machine shock absorber directly replaces the following OEM and cross-reference part numbers:
WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This shock absorber is compatible with select GE front-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform.
Note: GE uses several different shock absorber part numbers across its washer lineup, including separate parts such as WH01X10727 and WH03X29516 for other platforms. This WH01X20826 shock is specific to the front-load models listed above and is not interchangeable with those other GE shocks. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement shock absorber — dampens tub vibration and movement during spin
Sold individually — order four to replace the full set on a typical front-load washer
Resolves "excessive vibration," "banging or knocking noise," and "washer walking across the floor" symptoms caused by worn or detached shocks
Durable plastic and rubber construction for long-term damping performance
Direct drop-in replacement — no modification required
Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130.
Compatible with GE, Hotpoint, Haier, Monogram, Café, and select Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPWH01X20826
OEM Part Number
WH01X20826
Part Type
Washing Machine Shock Absorber (Damper)
Condition
Aftermarket Replacement
Application
GE Front-Load Washers
Material
Plastic and rubber
Function
Dampens tub vibration and movement during spin
Typical Quantity Per Washer
4 (this listing is for 1 individual shock)
Quantity
1 shock absorber
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café, Kenmore
Installation Notes
⚠️ Unplug Washer Before Starting — Consider Replacing All Four Shocks Together Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shock absorbers typically requires removing the top and/or front panel of the washer to reach the tub suspension points — check your model's service diagram, since access varies. Photograph how each old shock absorber connects to the frame and the tub before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Disconnect the old shock absorber from its mounting point at both the frame and tub ends, and remove the mounting pin. Install the new shock absorber in the same position with its mounting pin, matching the original orientation. If you're only replacing one shock, be aware the remaining three original shocks are the same age and under the same stress — many technicians recommend ordering three more of this same part and replacing all four together to avoid reopening the washer again soon after. Once installed, gently rock the tub by hand to confirm even resistance at each corner before reassembling the panels. Restore power and run a full spin cycle to confirm the vibration, shaking, or banging noise has resolved. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
Do I need to order more than one of these?
This listing is for a single shock absorber, but GE front-load washers use four of them working together around the tub. If one has failed, it's strongly worth ordering four total and replacing the full set, since all four are typically the same age and have been under the same stress — replacing just one risks having to reopen the washer again soon after for the next one.
My washer started shaking right after I moved it to a new spot. Is that related?
Yes, this is a documented cause of shock absorber problems on this platform. If the tub wasn't properly secured or the washer was tilted significantly during a move, one or more shock absorbers can separate from their mounting point. Check that all four shocks are still properly connected at both ends before assuming a shock itself has failed — sometimes reseating a separated shock is all that's needed, though if it shows wear it's worth replacing regardless.
How much vibration is normal, and how do I know it's actually the shocks?
Some vibration during high-speed spin is normal, especially with an unbalanced load. But vibration strong enough to move the washer across the floor, or accompanied by a banging or knocking noise from inside the cabinet, points to a suspension problem rather than a simple unbalanced load. Try redistributing the laundry evenly in the drum and running the spin cycle again — if the shaking persists with a balanced load, inspect the shock absorbers for wear, cracking, or separation.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, mounting configuration, and damping performance of the original WH01X20826 shock absorber used in compatible GE, Hotpoint, Haier, Monogram, Café, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
