WD26X10025 Dishwasher Genuine OEM Drain Pump
Fits Specific GE Dishwasher Models.
Replaces Part Numbers: WD26X10025, 1168314, AH1021347, EA1021347, OEM15537486, AP3884371, PS1021347.
Description: This Drain Pump Assembly is an OEM part for GE dishwashers. This component is responsible for removing water from the dishwasher during the drain cycle, ensuring that your dishes are cleaned and rinsed effectively. The pump works by expelling the used water through the drain hose and into the household plumbing.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WD26X25104 Dishwasher Genuine OEM Drain Pump
Fits Specific GE Dishwasher Models.
Replaces Part Numbers: WD26X25104, WD26X22810, WD26X20306, AP6990087, PS16217045
Description: The Variable Drain Pump Kit is a Genuine OEM replacement part for select GE built-in dishwasher models. It includes both the drain pump and clamps needed to remove water from the dishwasher during cycles. Common causes are blockages in the drain hose inhibiting water outflow or failure of the electric pump motor components over extended use.
PK136277-2 Lower Dishrack Roller and Axle Set
Pack of 2
Replaces: WD12X10136, WD12X10277
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
ERP 3129480 Dryer Drum Support Roller Shaft
Fits Specific Maytag, Amana, Admiral Dryer Models.
Replaces Part Number: WP6-3129480, 6-3129480, 1480353, 3-12948, 312948, W10912638, WP6-3129480VP, Y312948, AP6009858, PS11743031.
Description: The Dryer Drum Roller Axle is a replacement part for specific Maytag, Admiral, Whirlpool dryer models. It plays a role in the dryer's operation by offering support and an axis for the drum roller to spin smoothly. This guarantees effective and balanced tumbling of clothes throughout the drying cycle.
This is an aftermarket part that can be used as a replacement for the OEM part.
W11126005CM Dishwasher Wash Vane Sensor
Description: This Sensor is a replacement component specifically designed for certain Whirlpool dishwasher models. It plays a crucial role in monitoring cycle conditions like temperature and soil levels to automatically customize wash sequences. Causes of a bad sensor can include leaking or faulty wiring disrupting signals over time, mineral buildup gumming internal mechanisms, or damage from impact.
Replaces Part Numbers: W11126005, W11503875, W10380177, W10380483, W10647239, AP6261394, PS12114437.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: California’s Proposition 65
XPARTCO W10195417 Dishwasher Lower Rack Roller
Replaces Part Numbers: WPW10195417, W10195417, AP6016764, PS11750057
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
8270020CM Dishwasher Door Spring
Door balance spring - 7.75" overall length.
Fits Whirlpool dishwashers.
Replaces Part Numbers:WP8270020, 8270020, AP6012319, PS11745526.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 5304519906 Dishwasher Pump and Motor Assembly
Product Overview
The XPARTCO 5304519906 Dishwasher Pump and Motor Assembly is designed to circulate water through the spray arms and ensure proper cleaning performance. This Motor & Pump Assembly is a replacement part for specific Frigidaire dishwasher models. This assembly is crucial for circulating water throughout the dishwasher during the wash and rinse cycles, ensuring that dishes are cleaned effectively. You should replace this motor and pump assembly if it becomes faulty. Common causes of a bad motor and pump assembly include electrical issues, wear and tear from regular use, or blockages caused by debris or food particles.
Quick Answer
If your dishwasher is not cleaning dishes, has weak spray pressure, makes unusual noises, or fails to circulate water, the 5304519906 pump and motor assembly may be faulty. Replacing it restores proper wash performance and water circulation.
Replaces Part Numbers
Replaces OEM part number: 5304519906, 154843901, EAP12712308, AFR18422, PD00053471, AP6840161, P154792801.
Compatibility
This pump and motor assembly is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible dishwashers.
Frigidaire Dishwashers
Electrolux Dishwashers
Kenmore Dishwashers
Always verify your appliance model number before ordering.
Common Problems This Part Fixes
Dishes not getting clean
Weak or no water spray
Dishwasher making loud or grinding noise
Water not circulating during wash cycle
Key Features
Integrated pump and motor assembly
Restores strong water circulation
High-quality aftermarket replacement
Reliable and durable construction
Product Specifications
Part Number: XP5304519906
Part Type: Dishwasher Pump and Motor Assembly
Brand: XPARTCO
Condition: New
OEM / Aftermarket: Aftermarket
Application: Dishwasher Water Circulation
Troubleshooting Guide
Dishes remain dirty → Weak or failed pump motor
No spray action → Pump not circulating water
Loud noise during wash → Motor or impeller issue
When Should You Replace This Assembly?
Replace this assembly if your dishwasher is not cleaning properly, lacks water pressure, or makes abnormal noises during operation.
Installation Notes
⚠️ Disconnect power and water supply before installation. Access the pump and motor assembly from the bottom of the unit and install securely according to your dishwasher model.
Related Parts
Dishwasher Spray Arm
Water Inlet Valve
Drain Pump
Frequently Asked Questions
Will this assembly fit my dishwasher?This part fits many Frigidaire and compatible dishwashers. Always verify your model number.
What does a pump and motor assembly do?It circulates water through the dishwasher to clean dishes effectively.
What are signs of a bad pump motor?Poor cleaning, weak spray, or loud noises during operation.
Is this OEM or aftermarket?This is a high-quality aftermarket replacement part.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support.
Fast Shipping Quality Tested Parts Compatibility Support
AEC74337401 Dishwasher Water Inlet Guide - Compatible with LG Dishwashers
Product Description
Restore your dishwasher’s cleaning performance with the AEC74337401 Water Inlet Guide from Parts-O-Matic. This genuine OEM replacement guide directs water from the inlet valve into the dishwasher tub, ensuring proper water flow for wash and rinse cycles. Designed for LG dishwashers, it fixes issues like insufficient water, poor cleaning, or water inlet error codes.
Note: Includes one water inlet guide. Take photos of connections during disassembly and clean the inlet valve before installation.
Replaces part numbers: AEC74337401, AP6233501, PD00056036, PS12078211.
Compatibility:
Compatible with models including but not limited to:
Verify your model number or contact Parts-O-Matic support for assistance.
Key Features:
✅ Brand Compatibility: Fits select LG dishwasher models.
💧 Specifications: OEM plastic water inlet guide, designed for secure water flow and durability.
💰 Cost-Effective: OEM performance at a competitive price.
🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–30 minutes.
🛡️ Reliable Fixes: Resolves insufficient water, poor cleaning, or water inlet error codes.
Installation Notes:
Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks.
Clean the inlet valve and hose to prevent clogs.
Access the inlet guide (inside or near the bottom of the dishwasher), disconnect the old guide, and install the new one, ensuring tight connections.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today!
Add to cart now for a budget-friendly fix!
W10518394 Genuine OEM Whirlpool Dishwasher Heating Element
The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades.
This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed.
Common Problems This Part Fixes
Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase
Wash water not getting hot enough — poor cleaning performance even with proper detergent
Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation
Heated dry cycle not working — no warm air at the end of the cycle
Element visibly burned through, broken, or showing arcing damage
Multimeter continuity test on the element shows an open circuit (no continuity)
Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element)
Detergent not fully dissolving — water too cool to activate the formulation
Replaces Part Numbers
This dishwasher heating element directly replaces the following OEM and cross-reference part numbers:
W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead.
Compatibility
This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including:
Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models
Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram)
Maytag dishwashers — select models (verify with parts diagram)
KitchenAid dishwashers — select models
Amana dishwashers — ADB1400AGW and related models
Kenmore / Sears dishwashers — select Whirlpool-built models
Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase
Rated 1200W for efficient heating and reliable temperature control
Oval-shape element approximately 15" L x 3" W x 3" H
Mounts in the bottom of the dishwasher tub, secured underneath with large nuts
Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement
Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times)
Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070
Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
W10518394
Part Type
Dishwasher Heating Element
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Shape
Oval (NOT interchangeable with horseshoe-style elements)
Wattage
1200W
Dimensions
Approximately 15" L x 3" W x 3" H
Mounting Location
Bottom of dishwasher tub
Related Parts (Sold Separately)
Rubber Washer (717273), Heater Nut (8268548)
Post-Install Step
Diagnostic reset required on most Whirlpool dishwashers
Compatible Brands
Whirlpool, Maytag, KitchenAid, Amana, Kenmore
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses.
Frequently Asked Questions
Why are my dishes coming out wet — is the heating element the cause?
Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed.
After installing the new element, the dishwasher still isn't heating — why?
On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well.
How is the W10518394 different from horseshoe-shape heating elements?
The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher.
Do I need to replace the rubber washers and nuts when installing this?
Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WR2X7054CM Dishwasher / Refrigerator Push-on Nut
Push on retainer clip.
Used on GE dishwashers and refrigerators.
Replaces Part Numbers:WR2X7054, WD02X0429, WD2X429, WR02X7054, AH298353, EA298353, AP2059046, PS298353.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
