Search results for "refrigerator damper"

XPARTCO 3392519 Dryer Thermal Fuse Replaces WP3392519 The XPARTCO 3392519 is an aftermarket replacement dryer thermal fuse compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. The thermal fuse is a critical one-time-use safety device mounted on the exhaust duct or blower wheel housing that monitors the dryer's operating temperature. When the dryer overheats — typically due to a clogged exhaust vent or restricted airflow — the thermal fuse permanently opens the circuit and cuts power to the heating system to prevent a fire. Once blown, the thermal fuse cannot be reset and must be replaced. This part measures 2 inches long x 1/2 inch wide, features two 3/16-inch terminals, and opens at approximately 196°F (91°C). Important: always check and clear the exhaust vent when replacing this fuse, as restricted airflow is the most common cause of thermal fuse failure. Quick Answer The XPARTCO 3392519 Dryer Thermal Fuse fixes dryers that won't start, won't heat, or stop mid-cycle due to overheating. It is a one-time-use safety fuse that permanently opens at 196°F (91°C) to cut power and prevent fires. Compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef dryers. Replaces WP3392519 and many other part numbers. Common Problems This Part Fixes Dryer won't start at all Dryer runs but produces no heat Dryer stops mid-cycle and won't restart Timer advances but drum does not heat Dryer shuts off too soon before clothes are dry No continuity detected across fuse terminals during testing Replaces Part Numbers This thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (including Duet and Cabrio series) Kenmore / Sears dryers (including Elite series) KitchenAid dryers Maytag dryers (including Centennial and Neptune series) Roper dryers Estate dryers Inglis dryers Crosley dryers Amana dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-time-use safety device — permanently opens at 196°F (91°C) to cut power and prevent dryer fires Mounts on the exhaust duct or blower wheel housing — easy access for DIY replacement Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Broad compatibility across 11 major appliance brands DIY-friendly repair — installs with basic hand tools in under 30 minutes Budget-friendly safety fix — one of the most common and least expensive dryer repairs Product Specifications Part Number 3392519 Part Type Dryer Thermal Fuse Condition Aftermarket Replacement Application Gas and Electric Dryers Opening Temperature 196°F (91°C) Length 2 inches Width 1/2 inch Terminal Size 3/16 inch (2 terminals) Resettable No — one-time use only, must be replaced when blown Location on Dryer Exhaust duct / blower wheel housing Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef Installation Notes ⚠️ Safety First — Unplug Dryer and Shut Off Gas Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. The thermal fuse is located on the exhaust duct or blower wheel housing — access it by removing the back or front panel depending on your dryer model. Disconnect the two wire terminals from the old fuse, remove the fuse from its bracket, install the new fuse in the same position, reconnect the terminals, and reassemble the panel. Tools needed: Phillips screwdriver, 1/4-inch nut driver, and a multimeter to confirm the new fuse has continuity. ⚠️ Important: Before completing the repair, always check and clear the exhaust vent of any lint buildup — a blocked vent is the most common cause of thermal fuse failure and will blow the new fuse if not corrected. Frequently Asked Questions Will the 3392519 fit my dryer? This thermal fuse is compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. Use the model search above to verify your model, or contact our support team before ordering. What does a dryer thermal fuse do? The thermal fuse is a one-time-use safety device that monitors the temperature inside the dryer. When the dryer overheats — typically due to a clogged exhaust vent — the fuse permanently opens the circuit, cutting power to the heating system to prevent a fire. Once blown, it cannot be reset and must be replaced. How do I know if my thermal fuse is blown? Test the fuse with a multimeter set to continuity mode. Touch the probes to each of the two terminals. A working fuse will show continuity (beep or near-zero ohms). A blown fuse will show no continuity (open circuit). If there is no continuity, the fuse is blown and must be replaced. Why did my thermal fuse blow? The most common cause is restricted airflow due to a clogged or kinked exhaust vent, a plugged lint trap, or a damaged blower wheel. Always check and clear the exhaust vent before or after replacing the fuse — failing to do so will cause the new fuse to blow again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable overheat protection at a more affordable price point. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE04X20685 Genuine OEM GE Dryer Thermistor The WE04X20685 is a genuine GE OEM center outlet thermistor for GE dryers, and also fits select Hotpoint, RCA, and Kenmore models. This thermistor monitors exhaust air temperature and communicates real-time readings to the control board, letting it track how the dryer is operating throughout the cycle. Importantly, this thermistor is not part of the heating circuit itself, so it's unlikely to be the cause of a dryer that won't heat or produces too much or too little heat. Instead, when this thermistor malfunctions, it typically affects cycle timing or triggers a fault code, since the control board is receiving inaccurate or missing temperature data from this specific sensor location rather than losing its ability to regulate the heating element. A healthy thermistor reads approximately 100K ohms at room temperature. Common failure causes include moisture exposure gradually degrading the electronics over time, or physical stress damaging the thin connecting wires. Before assuming this thermistor is the cause of any symptom, it's worth confirming your exhaust venting has good airflow and is free of obstructions. It directly replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518. Quick Answer The WE04X20685 Genuine OEM GE Dryer Thermistor fixes GE, Hotpoint, RCA, and Kenmore dryers with incorrect cycle timing or a fault code related to this sensor. Reads approximately 100K ohms at room temperature. Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518. This thermistor is not part of the heating circuit — it's unlikely to be the cause of a no-heat or overheating problem, but can affect cycle timing or trigger a fault code if defective. Common Problems This Part Fixes Incorrect or inconsistent cycle timing Fault code related to this thermistor or temperature sensing Erratic cycle behavior not explained by a heating element or thermal fuse issue Control board receiving inaccurate temperature data from this sensor location Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermistor directly replaces the following OEM and cross-reference part numbers: WE04X20685, WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is compatible with select GE dryers, and also fits select Hotpoint, RCA, and Kenmore dryers built on the GE platform. Note: This is a center outlet thermistor and is not in the heating circuit — a different function from some other GE thermistors that do regulate heat output directly. Always verify your full model number before ordering, since GE uses different thermistor designs and resistance ratings across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified resistance curve and mounting fit Center outlet thermistor monitors exhaust air temperature and reports it to the control board Not part of the heating circuit — affects cycle timing and fault codes rather than heat output Reads approximately 100K ohms at room temperature Direct drop-in replacement matching the original mounting and wiring Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518 Compatible with GE, Hotpoint, RCA, and Kenmore dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WE04X20685 Part Type Dryer Center Outlet Thermistor Condition Genuine OEM Brand GE In Heating Circuit No Typical Resistance Approx. 100K ohms at room temperature Function Monitors exhaust air temperature and reports to the control board Repair Difficulty Easy Quantity 1 thermistor Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Check Venting Before Assuming This Sensor Is At Fault Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Before replacing this thermistor, confirm that airflow at the home's outside vent hood is good and that the dryer's venting is free of obstructions, since this thermistor is not part of the heating circuit and won't cause a heating problem on its own. Remove the back panel of the dryer, typically secured with several screws, to access the thermistor's mounting location. Test the old thermistor with a multimeter for electrical continuity to confirm it's actually faulty before replacing it. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old thermistor and remove it from its mounting position. Install the new WE04X20685 in the same position, reconnect the wire terminals, and reattach the back panel. Restore power and run a test cycle to confirm normal cycle timing with no fault codes. Tools needed: Phillips or nut driver (model-dependent), multimeter, work gloves. Frequently Asked Questions My dryer isn't heating. Is this thermistor the cause? Unlikely. This is a center outlet thermistor and is specifically not part of the dryer's heating circuit, so a fault here is unlikely to explain a no-heat or overheating symptom. If your dryer isn't heating, check the thermal fuse, heating element, or high-limit thermostat first. This thermistor is more likely to be the cause if you're seeing incorrect cycle timing or a specific fault code instead. What symptoms does this thermistor actually cause when it fails? Since this sensor feeds temperature data to the control board without being in the heating circuit itself, a failure here typically shows up as incorrect cycle timing or a fault code related to this specific sensor, rather than affecting how hot or cold the dryer runs. Should I check anything else before replacing this part? Yes — confirm your dryer's exhaust venting has good airflow and no obstructions before assuming this thermistor is at fault, since venting issues can cause a range of symptoms that might otherwise be mistaken for a sensor problem. This is a quick check worth doing first. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original resistance curve and mounting configuration of the thermistor originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10195622 Dishwasher Dish Rack Stop Clip Replaces WPW10195622 The XPARTCO W10195622 is an aftermarket replacement upper dishrack stop clip for Whirlpool dishwashers, and also fits select Jenn-Air, Kenmore, KitchenAid, and Amana models. This small plastic clip mounts at the back end of the upper dishrack's slide rail, preventing the rack from sliding in too far and striking the rear wall of the dishwasher cabinet, or from coming off the track entirely when pulled out. Light gray in color, measuring approximately 1-1/4" wide, and sold individually — one clip works for either the left or right side of the upper rack. Over time, the plastic can crack or break from repeated use, allowing the rack to slide too far or come loose from its track. A broken stop clip typically shows up as the upper rack sliding out too far, coming off the rails, or falling when pulled forward. It directly replaces WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071. Quick Answer The W10195622 Dishwasher Dish Rack Stop Clip fixes Whirlpool, Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers where the upper rack slides too far, comes off the rails, or falls out when pulled forward. Light gray, approx. 1-1/4" wide, sold individually. Replaces WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071. This clip is sold individually — if both the left and right stops need replacing, order two. Common Problems This Part Fixes Upper dishrack slides in too far and hits the rear wall of the cabinet Upper dishrack comes off the slide rail when pulled forward Upper dishrack falls out of the dishwasher Broken or missing stop clip visible at the back of the track Rack rollers coming out of the track Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher dish rack stop clip directly replaces the following OEM and cross-reference part numbers: WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This stop clip is compatible with select Whirlpool dishwashers, and also fits select Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers built on the Whirlpool platform, including model numbers such as WDT710PAHZ, WML35011KB, WVU7130JS, KUDC10FXSS5, KUDE40FXBL1, WDT790SAYM1, 7WDT770PAYM0, 7WDT770PAYM1, 7WDT770PAYW0, 7WDT790SAYM0, and WDF730PAYB0. Note: This clip mounts at the back end of the slide rail/drawer track (a related but separate part, WPW10195623). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement upper dishrack stop clip Resolves "rack slides too far," "comes off the rails," and "rack falls out" symptoms Light gray, approximately 1-1/4" wide Works for either the left or right side of the upper rack Snap-fit installation — no screws required Sold individually Replaces WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071 Compatible with Whirlpool, Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10195622 OEM Part Number WPW10195622 Part Type Dishwasher Upper Dishrack Stop Clip Condition Aftermarket Replacement Color Light Gray Width Approx. 1-1/4" Fits Left or right side (universal for either) Related Part WPW10195623 slide rail/drawer track (sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 stop clip (sold individually) Compatible Brands Whirlpool, Jenn-Air, Kenmore, KitchenAid, Amana Installation Notes ⚠️ Unplug Dishwasher Before Starting Disconnect power to the dishwasher before beginning. Wear work gloves. Slide out the upper dish rack to locate the existing stop clip at the back end of the slide rail. Using a flathead screwdriver, gently pry out the old, broken stop clip from the track. Snap the new W10195622 clip into the same position at the back of the track, pressing it in firmly until it's securely seated — this is a snap-fit clip rather than a screwed connection. Slide the rack back onto the rails and test it by pulling it forward and pushing it back, confirming it stops properly at both ends without sliding off the track or hitting the rear wall. Tools needed: flathead screwdriver. Frequently Asked Questions My upper rack fell out of the dishwasher. Is this the part I need? Yes, this is a well-documented symptom of a broken stop clip. One customer described exactly this: "Plastic stop on upper dishwasher rack was broken allowing the rack to come out and fall," and resolved it by prying out the old, broken clip and snapping in a new one in just a few minutes. Do I need one clip or two? This part is sold individually, and one clip works for either the left or right side of the upper rack. If both the left and right stop clips need replacing, you'll need to order two. Do I need to screw this in, or does it snap into place? This clip snaps into place rather than being screwed in. A flathead screwdriver is useful for prying out the old, damaged clip, but installing the new one is a simple snap-fit into the track — no screwing required. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the size, color, and snap-fit mounting of the original WPW10195622 stop clip used in compatible Whirlpool, Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703 The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement. Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more. Common Problems This Part Fixes Violent shaking or vibrating during the spin cycle Loud banging, thumping, or clunking noise during spin Washer "walking" across the floor during the spin cycle Outer tub hitting the sides of the cabinet during high-speed spin Spin cycle errors caused by excessive tub movement triggering the imbalance sensor Visible oil leak, broken mount, or collapsed shock absorber body Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration Replaces Part Numbers This shock absorber directly replaces the following OEM and cross-reference part numbers: WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — GHW and WFW series Maytag front-load washers — MHWE and MFW series Kenmore / Sears front-load washers (select Whirlpool-built models) KitchenAid front-load washers — KHWS series Amana front-load washers Jenn-Air front-load washers Admiral front-load washers Roper front-load washers Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after. Key Features Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life Direct replacement for WP8182703 and 8181646 — no modification required Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers Sold individually — most models require 4 shock absorbers; replace all 4 at the same time Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 8182703 OEM Part Number WP8182703 Part Type Front-Load Washer Shock Absorber (Hydraulic Dampener) Condition Aftermarket Replacement Application Front-Load Washers Quantity Per Washer 4 (2 front, 2 rear) — sold individually Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper Compatible Series GHW, WFW, MHWE, MFW, KHWS Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves. Frequently Asked Questions What does the washer shock absorber do? The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time. How many shock absorbers does my front-load washer have? Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one. What is the difference between 8182703 and WP8182703? These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers. My washer still vibrates after replacing the shock absorbers — what else could it be? If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WR55X11132 Refrigerator LED Light Product Overview The XPARTCO WR55X11132 Refrigerator LED Light provides bright, energy-efficient illumination inside your refrigerator, improving visibility and enhancing overall appliance functionality. This high-quality LED module restores clear lighting for easy food access. Note: This is LED Light only, Cover is not included. Quick Answer If your refrigerator light is dim, flickering, or not turning on, the WR55X11132 LED light module may be faulty. Replacing it restores proper interior lighting and visibility. Replaces Part Numbers Replaces OEM part number: WR55X11132, EAP4704284, AGE28811, PD00030062, AP5646375, 3033142, PS4704284. Compatibility This refrigerator LED light is compatible with select GE, Hotpoint, and GE Profile refrigerators. . GE Refrigerators: GFE26GGHBBB, GFE26GGHBWW, GFE26GGHCBB, GFE26GGHCWW, GFE26GGHDBB, GFE26GGHDWW, GFE26GGHEBB, GFE26GGHEWW, GFE26GGHFBB, GFE26GGHFWW, GFE26GGHGBB, GFE26GGHGWW, GFE26GGKBBB, GFE26GGKBWW, GFE26GMHBES, GFE26GMHCES, GFE26GMHDES, GFE26GMHEES, GFE26GMHGES, GFE26GMKBES, GFE26GSHBSS, GFE26GSHCSS. Always verify your appliance model number before ordering. Common Problems This Part Fixes Refrigerator light not working Dim or flickering LED light Poor visibility inside fridge Key Features Bright LED illumination Energy-efficient lighting Long-lasting performance High-quality aftermarket replacement Product Specifications Part Number: XPWR55X11132 Part Type: Refrigerator LED Light Module Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Refrigerator Interior Lighting Troubleshooting Guide No interior light → Failed LED module Flickering light → Failing LED board Dim lighting → Aging LED unit When Should You Replace This Light? Replace this LED light if your refrigerator interior lighting is not functioning properly or has become dim or inconsistent. Installation Notes ⚠️ Disconnect power before installation. Remove the light cover, disconnect the module, and install the new LED light securely. Related Parts Refrigerator Door Switch Control Board Light Cover Frequently Asked Questions Will this light fit my refrigerator?This LED module fits many GE and compatible models. Always verify your model number. Is this LED or bulb type?This is an LED light module, not a traditional bulb. What are signs of a bad LED module?No light, flickering, or dim lighting indicate replacement is needed. Is installation difficult?Most modules are easy to replace, but follow your appliance manual for best results. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

D510181 Genuine OEM Dryer Metal Door Strike - Compatible with Speed Queen, Alliance, Huebsch Product Description Secure your dryer door with the D510181 Genuine OEM Dryer Metal Door Strike. This Speed Queen-manufactured metal strike is designed as a replacement for select Speed Queen, Alliance, Huebsch, and other compatible dryers. It latches into the door catch when the dryer door is closed, ensuring a secure seal during operation. This part addresses issues like the door not closing properly or not staying closed, often caused by a worn or damaged strike. Note: Includes (1) metal door strike. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: D510181, 510181, 500039, 54661, H87020228, PD00041917, TU21401, AP6284686. Compatibility: Compatible with select dryer models, including but not limited to: Speed Queen: ADE3SRGS175TW01, ADE4BRGS175TW01, ADEE9BGS175TW01, KDEBXRGS175TW01 Alliance: JDEJEAGW303EW01, JDEJGAGW303EW01, JSGJEAGW303EW01 Huebsch: YDE3TRGS171CW01, YDE4BRGS171CW01 Econowash: CA025L, CA025N Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Speed Queen, Alliance, Huebsch, Econowash, and other dryers. 🔧 Specifications: Genuine OEM Speed Queen metal door strike, corrosion-resistant. 💪 Reliable Performance: Ensures secure door closure for safe and efficient drying. 🛠️ Easy Installation: Requires pliers; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves door not closing or staying closed issues. Product Specification Part Number: D510181 Component Type: Dryer door strike Material: Metal Additional Specs: Corrosion-resistant metal, designed for front panel attachment  Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a reliable fix!

Read more less

Genuine Bosch 00617090 Microwave Waveguide Cover - Compatible with Bosch Microwaves Product Description Protect your microwave with the Genuine Bosch 00617090 Microwave Waveguide Cover. This OEM waveguide cover is designed for select Bosch built-in microwaves, shielding the magnetron from food splatter and moisture to ensure safe and efficient operation. Made of silicone-bonded mica and measuring approximately 4-1/8" x 2-5/8"", it prevents arcing, sparking, or microwave failure due to a damaged cover, delivering reliable performance as an authentic Bosch part. Note: Includes one waveguide cover. Disconnect power before installation. Inspect waveguide channel for debris to ensure optimal performance. Replaces part numbers: 00617090, 12014089, PD00053143, EAP9492671, AP5806321, PS9492671. Compatibility: Compatible with models including but not limited to: Bosch: HBL5751UC/01, HBL8751UC/01, HMC80151UC/01, HMC87151UC/01, HMC80152UC/01, HMC80251UC/01, HMC80252UC/01, HMC87152UC/01, HMB50152UC/01, HMB50162UC/01, HMB57152UC/01 Thermador: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Bosch built-in microwaves. 🛡️ Specifications: OEM waveguide cover, silicone-bonded mica, approximately 4-1/8" x 2-5/8". 💪 Reliable Performance: Authentic Bosch part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver; typically installed in 5–10 minutes. 🔥 Effective Fixes: Prevents arcing, sparking, or microwave failure due to damaged cover. Product Specification Part Number: Genuine Bosch 00617090 Component Type: Microwave waveguide cover Material: Silicone-bonded mica Mounting: Screw-mounted or clip-in (model-dependent) Operating Conditions: Suitable for high-temperature microwave environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the microwave from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your microwave running safely today! Add to cart now for a reliable fix!

Read more less

17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools. Quick Answer The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models. Common Problems This Part Fixes Dryer overheating — thermistor not accurately reporting rising temperature to the control board Dryer not heating at all — thermistor circuit open or shorted Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle Dryer taking much longer than normal to complete a cycle Not-heating fault code displayed on models with digital control panels Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading Dryer cycling heat on and off erratically Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 17438200000404, WF-123X2060, AP7157538, PS18188581 Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including: Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13 Criterion — CDE41N1AW (electric), CDG41N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models Replaces WF-123X2060 Installs in 20–30 minutes with basic hand tools Product Specifications Part Number 17438200000404 Part Type Dryer Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at Room Temp Approximately 10,000 – 12,000 ohms (~70°F) Location Blower housing/exhaust duct or drum cavity, depending on model Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing). Frequently Asked Questions How do I test if the temperature sensor (thermistor) has failed? Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine. My Midea dryer has more than one temperature sensor — how do I know which one to replace? Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor. What is the difference between 17438200000404 and WF-123X2060? These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part. Does this sensor fit my Insignia or Criterion dryer? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool WP37001042 Dryer Drum Roller - Compatible with Admiral, Amana, Magic Chef, Maytag, Speed Queen Product Description Restore smooth and quiet operation to your dryer with the Genuine Whirlpool WP37001042 Dryer Drum Roller. This OEM drum roller is designed for select Admiral, Amana, Magic Chef, Maytag, and Speed Queen dryers, supporting the drum for even tumbling and efficient drying. Made of durable rubber, metal, and plastic, it ensures long-lasting performance, addressing issues like loud rumbling, squeaking, or uneven drum movement. Note: Includes one drum roller. Disconnect power and gas (if applicable) before installation. For even wear, replace all rollers at the same time. Replaces part numbers: WP37001042, 37001042, 14218934, 500214, 500214P, WP37001042VP, 5-0214, 500214P-REPL, 500214-REPL,37001042-REPL, 500214P, 500214, PD00002495, EAP11741913, AP6008773, PS11741913. Compatibility: Compatible with models including but not limited to: Admiral: ADE7005AKW, ADE7005AYW, ADE9005AGW, ADG7005AWW Amana: AEM197, AEM377, AEM397, AEM407L, AEM407W, ALE120RAW, ALE230RAW Maytag: MDE3706AGW, MDG2706AGW Speed Queen: AGM199, AGM379, AGM399 Bosch, Crosley, Danby, Kenmore, Magic Chef: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Admiral, Amana, Magic Chef, Maytag, and Speed Queen dryers. 🔄 Specifications: OEM drum roller made of rubber, metal, and plastic for smooth drum rotation. 💪 Reliable Performance: Authentic Whirlpool part ensures superior durability and performance. 🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves loud rumbling, squeaking, or uneven drum movement. Product Specification Part Number: Genuine Whirlpool WP37001042 Component Type: Dryer drum roller Material: Rubber, metal, plastic Mounting: Bolt-mounted to dryer drum assembly Operating Conditions: Suitable for household and commercial dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO 691366 Dryer Idler Pulley Assembly Replaces WP691366 The XPARTCO 691366 is an aftermarket replacement dryer idler pulley assembly compatible with a wide range of Whirlpool-family dryers — particularly models with the lint filter on top — including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef, and Norge. The idler pulley assembly is a spring-tensioned arm and wheel that presses against the drum drive belt to maintain correct belt tension as it wraps around the drum and motor pulley. Without proper tension, the belt slips off the motor pulley, causing the drum to stop spinning. A worn idler pulley bearing also causes squealing, squeaking, or thumping noises during operation. This is a complete idler arm and pulley assembly — it includes both the spring arm and the wheel, and mounts directly to the existing bracket in the dryer. Overall dimensions are 6"L x 1-5/8"W x 3-7/8"H with a 1-7/8" diameter pulley wheel. It replaces older Teflon friction-style idler pulleys and provides a smoother, longer-lasting ball-bearing wheel. It directly replaces WP691366, 691366, 239477, 337116, 337407, 3394332, 347034, 347226, 4319391, 688166, W10612905, AP6010582, PS11743765, and over 20 additional cross-reference numbers. Often replaced together with the drum belt (341241) and drum support rollers (349241T) as the 4392065 maintenance kit. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 691366 Dryer Idler Pulley Assembly fixes Whirlpool-family dryers that are squealing, thumping, or where the drum stops spinning because the belt has lost tension. Complete arm and pulley assembly. 6"L x 1-5/8"W x 3-7/8"H overall, 1-7/8" pulley diameter. Replaces older Teflon friction pulleys with ball-bearing wheel. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, and more. Replaces WP691366, 239477, 337116, 3394332, 347034, AP6010582, PS11743765. Often replaced with 341241 belt and 349241T rollers. Common Problems This Part Fixes Drum not spinning — belt has lost tension and slipped off the motor pulley Loud squealing or squeaking noise during the drying cycle — worn idler pulley bearing Thumping or clunking noise as the pulley wheel wobbles on a worn bearing Belt repeatedly slipping or falling off after being reinstalled Grinding noise from the idler pulley area — bearing fully failed Dryer drum spinning intermittently due to inconsistent belt tension Idler pulley arm visibly cracked, broken, or wheel no longer spinning freely Replaces Part Numbers This idler pulley assembly directly replaces the following OEM and cross-reference part numbers: WP691366, 691366, 239477, 26000691366, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, WP691366VP, AWP48059, EAP11743765, AP6010582, PD00002256, PS11743765. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley assembly is compatible with select gas and electric dryers from the following brands — particularly models with the lint filter on top: Whirlpool dryers (gas and electric — WED, WGD, LE, LG, and related series with top lint filter) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Norge dryers Note: The 691366 idler pulley is for older Whirlpool-family dryers with the lint filter on top. Newer Whirlpool dryers with the lint screen inside the door use the W10837240 idler pulley arm assembly instead. Always verify your model number before ordering. Key Features Complete idler arm and pulley assembly — includes both the spring-tensioned arm and the pulley wheel Maintains correct drive belt tension so the belt grips the drum and motor pulley without slipping Redesigned ball-bearing pulley wheel replaces older Teflon friction-style pulleys for longer service life and quieter operation Overall dimensions: 6"L x 1-5/8"W x 3-7/8"H; pulley wheel diameter: 1-7/8" Plastic arm with metal shaft and ball-bearing pulley wheel Replaces WP691366, 239477, 337116, 3394332, 347034, AP6010582, and over 30 additional cross-reference numbers Compatible with 12 major appliance brands on the Whirlpool top-lint-filter platform Often replaced together with the drum belt (341241) and drum rollers (349241T) — all three included in the 4392065 maintenance kit Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 691366 OEM Part Number WP691366 Part Type Dryer Idler Pulley Assembly (Arm and Wheel) Condition Aftermarket Replacement Application Gas and Electric Dryers (lint filter on top models) Overall Dimensions 6"L x 1-5/8"W x 3-7/8"H Pulley Wheel Diameter 1-7/8 inches Material Plastic arm / Metal shaft / Ball-bearing pulley wheel Color Black / White Includes Complete idler arm and pulley assembly Often Replaced With 341241 Drum Belt, 349241T Drum Rollers (4392065 kit) Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to fully access the drum drive components. Release belt tension by pushing the idler pulley arm toward the motor and sliding the belt off. Note how the belt is routed before removing — take a photo. Unclip or unscrew the old idler pulley assembly from its mounting bracket. Install the new 691366 idler pulley in the same position. Re-route the belt around the drum (ribbed side in), under the idler pulley, and around the motor pulley, then release the idler arm to create tension. Reassemble the front and top panels, restore power, and run a test cycle. Tip: while the dryer is open, inspect and replace the drum belt (341241) and drum support rollers (349241T) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife. Frequently Asked Questions What does the idler pulley do? The idler pulley is a spring-loaded arm and wheel assembly that presses against the drive belt between the drum and the motor pulley, keeping the belt under constant tension. This tension is what allows the belt to grip both the drum and the motor pulley without slipping as the motor spins. Without proper tension — or with a pulley bearing that has failed — the belt slips, the drum stops spinning, and the dryer produces heat but does not tumble clothes. A worn bearing also creates the high-pitched squealing sound that is the most common sign of idler pulley failure. What is the difference between 691366 and WP691366? These are the same idler pulley assembly. WP691366 is the updated Whirlpool OEM part number that superseded the original 691366. The W10612905 is also a cross-reference for the same assembly. This aftermarket replacement is compatible with all three numbers. What is the difference between 691366 and W10837240? Both are Whirlpool dryer idler pulley assemblies, but for different dryer generations. The 691366 (WP691366) is used on older Whirlpool-family dryers with the lint filter on top of the dryer. The W10837240 is a larger, redesigned idler arm and bracket assembly used on newer Whirlpool-family dryers with the lint screen inside the door. They are not interchangeable. Always verify your model number to confirm which idler pulley is correct for your dryer. Should I also replace the belt and drum rollers at the same time? Yes — since the dryer must be disassembled to replace the idler pulley, this is the ideal time to also inspect and replace the drum belt (341241) and rear drum support rollers (349241T). All three parts are part of the same drum drive system and wear at similar rates. The 4392065 maintenance kit includes all three together and is the recommended approach for a complete drum drive repair — one teardown covers everything. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with a ball-bearing pulley wheel to match the dimensions and performance of the original WP691366 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10757833 Dishwasher Control Panel Fits specific KitchenAid dishwasher models. Replaces Part Numbers: W10757833, 8531268, 3452787, 8531265, 8531537, 8564487, 8564565, AP5956414, PS10064580. Description: This Rack Adjuster is a Genuine OEM part for Whirlpool dishwashers, designed to allow for the easy adjustment of the dishwasher rack's height. This feature accommodates dishes of various sizes. By providing the flexibility to adjust the rack height, this part enhances the dishwasher's adaptability to different washing needs.

Read more less