Search results for "washer water valve"

XPARTCO 22003483 Washer Drive Belt The XPARTCO 22003483 is an aftermarket replacement drive belt for Whirlpool-built Maytag Atlantis top-load washers. This belt is the mechanical link between the drive motor and the washer's drive system — it's what actually transmits the motor's rotation to spin the drum, so both agitation and spin depend entirely on this belt gripping its pulleys correctly and staying properly tensioned. Made of black rubber, this belt measures 52 inches long. Over years of use, the belt material gradually hardens and glazes over, becoming smooth and "slick" rather than gripping the pulleys firmly — this degradation can cause the belt to slip under load even before it shows any visible cracking or damage. A worn belt produces a range of symptoms depending on how far the wear has progressed: the washer may pump water but fail to spin, fail to agitate at all, spin noticeably slower than normal, or produce a chirping or slipping noise, especially as the motor shifts between wash and spin modes. It directly replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667. Quick Answer The XPARTCO 22003483 Washer Drive Belt fixes Maytag (Whirlpool-built) top-load washers that pump but won't spin, won't agitate, spin slowly, or make a chirping/slipping noise as the motor shifts modes. 52 inches long, black rubber. Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, 824667. A belt can slip and cause symptoms well before it looks visibly worn — years of use leave the rubber "slick" and unable to grip the pulleys properly, even without visible cracking. Common Problems This Part Fixes Washer pumps water but won't spin Washer won't agitate Washer spins noticeably slower than it used to Chirping or slipping noise, especially as the motor shifts between wash and spin modes Belt that has become glazed, hardened, or "slick" from years of use Visible cracking, fraying, or glazing on the belt surface General noise or vibration during the wash or spin cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP22003483 22003483, 22002709, 62618130, 824667, AP6006365, EAP11739438, WP22003483VP, AWP47150, PD00002551, PS11739438 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Maytag Atlantis top-load washers built on the Whirlpool platform, including model numbers such as: MAV4057AWQ, MAV4057AWW, MAV4500AWW MAV5000AWQ, MAV5000AWW, MAV5057AWQ, MAV5057AWW, MAV5960AWW MAV6000AWQ, MAV6000AWW, MAV6057AWQ, MAV6057AWW MAV6200AWQ, MAV6200AWW, MAV6250AWQ, MAV6250AWW, MAV6257AWQ, MAV6257AWW MAV6548AWQ, MAV6548AWW, MAV6601AWQ, MAV6601AWW, MAV6650AWW, MAV7000AWQ Note: Always verify your full model number before ordering, since Whirlpool and Maytag use different belt lengths and profiles across their washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drive belt — transmits motor power to spin the washer drum Resolves "pumps but won't spin," "won't agitate," "spins slowly," and "chirping/slipping noise" symptoms caused by belt wear 52 inches long, black rubber construction Rides on three pulleys to transfer motor rotation to the drive system Direct drop-in replacement matching the original length and profile Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667 Compatible with Maytag Atlantis top-load washers built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 22003483 OEM Part Number WP22003483 Part Type Washer Drive Belt Condition Aftermarket Replacement Application Maytag Atlantis Top-Load Washers (Whirlpool-Built) Length 52 inches Material Rubber Color Black Function Transmits motor rotation to the drive system to spin the drum Quantity 1 drive belt Compatible Brand Maytag (Whirlpool-built) Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the motor and belt area. Loosen the motor's mounting screws so the motor can be pushed toward the drum, releasing tension on the old belt. Slide the old belt off its three pulleys and remove it. Route the new 22003483 belt over the same three pulleys, matching the original path. With the belt in place, gently push the motor away from the drum by hand to apply tension, then tighten the motor's mounting screws while continuing to check belt tightness — the belt should have firm, even tension across all three pulleys with no excess slack. Reinstall the rear panel, restore power, and run a full test cycle through both agitate and spin to confirm smooth, quiet operation with no chirping or slipping. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions My washer makes a chirping noise when it shifts from agitate to spin. Is that the belt? Yes, this is a documented symptom of a worn belt. One long-term owner traced this exact chirp to a 10-year-old belt that had become "slick" from age — smooth and hardened enough that it briefly slipped on the pulleys as the motor shifted between modes, rather than moving cleanly into position. Replacing the belt resolved the noise completely. My belt doesn't look cracked or damaged. Could it still be the problem? Yes. A belt can degrade in ways that aren't obvious at a glance — the rubber can harden and glaze over time, becoming slick and losing its grip on the pulleys even without visible cracking or fraying. If your washer is slipping, chirping, or spinning weakly and the belt has been in service for many years, age-related slickness is a reasonable explanation even if the belt still looks intact. How do I know if I have the right belt length for my washer? This belt is 52 inches long and specific to the Maytag Atlantis top-load platform. Whirlpool and Maytag use different belt lengths across other washer models, so always confirm your model number matches the compatibility list, or measure your old belt for comparison, before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, profile, and material of the original WP22003483 drive belt used in compatible Maytag Atlantis top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA97-07603B Genuine OEM Samsung Refrigerator Ice Maker The DA97-07603B is a genuine Samsung OEM ice maker assembly for Samsung and select Maytag refrigerators. This is the freezer ice maker, located inside the freezer compartment — it is not the in-door icemaker used on many other Samsung models. This is a plastic tray-style ice maker with a 9-cube flex tray design, an 8-pin connector, and includes a motor for ice ejection, a water valve to fill the mold, and a thermostat that senses temperature and signals when it's time to release the finished ice. This complete assembly contains the entire ice maker and its housing. If the mold's coating is flaking, or internal components have stopped functioning, replacing the full assembly resolves both problems at once. Failure symptoms include the ice maker not producing ice, reduced ice production, or loud popping sounds coming from the ice maker during operation. It directly replaces DA61-03213B, DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313. Quick Answer The DA97-07603B Genuine OEM Samsung Refrigerator Ice Maker fixes Samsung and select Maytag refrigerators where the freezer ice maker has stopped producing ice, is making less ice than usual, or is making loud popping sounds during operation. 9-cube flex tray, 8-pin connector. Replaces DA61-03213B, DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313. This is the freezer ice maker — it does not fit an in-door icemaker, and it is not a substitute for the DA97-07603C icemaker used on other models. Common Problems This Part Fixes Ice maker has stopped producing ice entirely Ice maker producing less ice than it used to Loud popping sounds coming from the ice maker during operation Ice mold coating visibly flaking or deteriorating Ice maker cycling but not ejecting ice properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers: DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This freezer ice maker is compatible with select Samsung refrigerators, and also fits select Maytag refrigerators built on the Samsung platform, spanning model series including RF220D, RF220N, RF221N, RF22A4, RF23HC, RF260BE, RF261BE, RF263TE, RF27T5, RF28HD, RF28HF, RF28R6, RF28T5, RF30HD, and RF323T, including specific model numbers such as RF220NCTABC/AAA-0001. Note — freezer icemaker only, and not a substitute for DA97-07603C: This is a drop-in replacement for the freezer icemaker only. It will not fit an in-door icemaker used on many other Samsung models. It also replaces the earlier DA97-07603A version, but is not a suitable substitute for the DA97-07603C icemaker used on other models, despite the similar numbering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which icemaker your refrigerator needs. Key Features Genuine Samsung OEM part — factory-specified mold design and cycling mechanism 9-cube flex tray design Includes motor for ice ejection, water valve for mold fill, and thermostat for temperature sensing Resolves "not making ice," "reduced ice production," and "loud popping sounds" symptoms 8-pin connector for a direct electrical fit Complete assembly — includes the ice maker and its housing Direct drop-in replacement for the freezer compartment icemaker Replaces DA61-03213B, DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313 Compatible with Samsung and select Maytag refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number DA97-07603B Part Type Refrigerator Freezer Ice Maker Assembly Condition Genuine OEM Brand Samsung Tray Style Plastic, 9-cube flex tray Connector 8-pin Location Freezer compartment (not an in-door icemaker) Included Components Ejection motor, water valve, thermostat, housing Repair Difficulty Easy — approx. 15 to 30 minutes Quantity 1 ice maker assembly Compatible Brands Samsung, Maytag Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the power outlet and turn off the water supply before beginning. Wear work gloves. On bottom-freezer drawer-style models, most of the time in this repair goes toward removing the trays from the freezer and pulling the freezer door/drawer out for access — budget extra time for this step. Remove the ice maker cover by lifting it away from the housing. Remove the ice bucket and any cover plates blocking access. Photograph the wiring connection before disconnecting anything. Unscrew the ice maker from its housing, disconnect the water line connection and the 8-pin electrical connector, and carefully lift the old assembly out of its compartment. Install the new DA97-07603B in the same position, reconnect the water line and electrical connector fully, and secure it to the housing with its screws. Reinstall the ice maker cover, cover plates, and ice bucket, then replace the freezer trays and close the freezer door/drawer. Restore the water supply and power, then allow several hours for the first cycle to complete and confirm ice is being produced normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My ice maker makes loud popping sounds. Is this the part I need? Yes, this is a documented symptom of a failing ice maker assembly, alongside reduced or stopped ice production. If you're hearing unusual popping noises during the ice-making cycle, replacing the complete assembly addresses the underlying mechanical or electrical issue rather than trying to isolate and repair a specific internal component. My refrigerator has an in-door ice maker. Will this part fit? No. This DA97-07603B is specifically a drop-in replacement for the freezer compartment icemaker and will not fit an in-door icemaker used on many other Samsung refrigerator models. Check where your current ice maker is physically located — inside the freezer versus built into the refrigerator door — before ordering. Is this the same as the DA97-07603C icemaker I've seen for other models? No. While this part does replace the earlier DA97-07603A version, it is explicitly not a suitable substitute for the DA97-07603C icemaker used on other Samsung models, despite the similar numbering. Always confirm your full model number rather than assuming based on a close part number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It matches the original mold design, motor, water valve, and thermostat configuration of the freezer ice maker originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X10025 Dishwasher Genuine OEM Drain Pump Fits Specific GE Dishwasher Models.  Replaces Part Numbers: WD26X10025, 1168314, AH1021347, EA1021347, OEM15537486, AP3884371, PS1021347. Description: This Drain Pump Assembly is an OEM part for GE dishwashers. This component is responsible for removing water from the dishwasher during the drain cycle, ensuring that your dishes are cleaned and rinsed effectively. The pump works by expelling the used water through the drain hose and into the household plumbing.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM WE03X23875 Dryer Drum Bearing Support - Compatible with GE, Hotpoint, RCA, Kenmore, and Fisher & Paykel Dryers Product Description Keep your dryer running smoothly with the Genuine OEM WE03X23875 Dryer Drum Bearing Support from Parts-O-Matic. This authentic GE front drum support assembly, designed for GE, Hotpoint, RCA, Kenmore, and Fisher & Paykel dryers, secures the drum at the front, ensuring smooth rotation during the drying cycle. Made of durable gray plastic, it includes bearings and a light fixture, addressing issues like squeaking, grinding noises, loose drum movement, or reduced drying efficiency caused by wear or damage. Note: Includes one front drum support assembly with bearings and light. Clean lint and debris from the drum and front panel before installation. Take photos of component placement during disassembly. Replaces part numbers: WE03X23875, EAP11767002, PD00050010, AP6037232, 4587455, PS11767002. Compatibility: Compatible with models including but not limited to: GE: GTD65EBSJ1WS, GTD65GBSJ0WS, GTD72GBPNDG, GTD84GCSNWS, GTD42EASJ0WW, GTDP490ED7WS Hotpoint: HTDX100EM8WW, HTDP120ED6WW RCA: RTD42EASJ0WW Kenmore: 2661532210, 36361532412 Fisher & Paykel: DG70FA1-96975, DE60FA-US1-96987 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Hotpoint, RCA, Kenmore, and Fisher & Paykel dryer models. 🔥 Specifications: OEM front drum support assembly, gray plastic, includes bearings and light fixture, designed for smooth drum rotation and durability. 💰 Genuine OEM Quality: Authentic GE part ensures perfect fit and reliable performance. 🛠️ Easy Installation: Requires a Phillips screwdriver, nut driver, work gloves; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves squeaking or grinding noises, loose or sagging drum, reduced drying efficiency, or unusual noises when opening/closing the door. Installation Notes: Safety First: Unplug the dryer from the power source before installation. Shop Parts-O-Matic for high-quality OEM appliance parts with a 30-day return policy. Keep your dryer running smoothly and efficiently today! Add to cart now for a reliable OEM fix!

Read more less

W11676494 Dryer Genuine OEM Knob Replaces Part Numbers: W11676494, W10215799, AP7215412, .

Read more less

XPARTCO W10837240 Dryer Idler Pulley The XPARTCO W10837240 is an aftermarket replacement idler pulley assembly compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The idler pulley maintains correct tension on the drive belt, allowing the belt to spin the dryer drum smoothly and consistently. When the idler pulley wears out, the belt loses tension — causing squeaking, grinding noises, or a drum that stops spinning entirely. This complete assembly includes the idler arm, pulley, and bracket — everything needed for a direct drop-in installation. The pulley is 2-1/8 inches in diameter and the overall assembly measures 6-1/4" L x 1-1/4" W x 3-7/16" H. It directly replaces OEM part numbers W10837240, W10547287, and W10547290, and fits Whirlpool-family dryers with the lint screen located inside the door. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W10837240 Dryer Idler Pulley fixes dryers that are squeaking, grinding, or have a drum that won't spin due to lost belt tension. Includes idler arm, pulley, and bracket. Pulley diameter 2-1/8". Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. Fits models with lint screen inside the door. Common Problems This Part Fixes Loud squeaking or squealing noise during dryer operation Grinding or rumbling noise as the drum rotates Dryer drum not spinning — belt loses tension when pulley bearing fails Belt repeatedly slipping off or breaking due to improper tension Dryer drum turning erratically or stopping while motor continues to run Excessive vibration or shaking during the drying cycle Visible wear, cracking, or a pulley that no longer spins freely on its shaft Replaces Part Numbers This idler pulley assembly directly replaces the following OEM and cross-reference part numbers: W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric — fits models with lint screen inside door) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) KitchenAid dryers Crosley dryers Admiral dryers Inglis dryers Roper dryers Important: The W10837240 fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley may be required. Contact our support team with your model number to confirm before ordering. Key Features Maintains correct tension on the drive belt for smooth, consistent drum rotation every cycle Complete assembly — includes idler arm, 2-1/8" diameter pulley, and bracket — ready to install Overall dimensions: 6-1/4" L x 1-1/4" W x 3-7/16" H Durable plastic and metal construction — resists wear and heat damage Direct replacement for W10837240, W10547287, and W10547290 — no modification required Updated design replaces older W10547287 and W10547290 assemblies Aftermarket replacement built to OEM-equivalent quality standards Often replaced together with the drum belt (WPW10112954 or 661570V) for a complete drum drive repair DIY-friendly repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number W10837240 Part Type Dryer Idler Pulley Assembly with Arm and Bracket Condition Aftermarket Replacement Application Gas and Electric Dryers Pulley Diameter 2-1/8 inches Overall Dimensions 6-1/4" L x 1-1/4" W x 3-7/16" H Material Plastic / Metal Color White Includes Idler arm, pulley, and bracket assembly Lint Screen Location Fits dryers with lint screen inside the door Compatible Brands Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper Often Replaced With WPW10112954 or 661570V Drum Belt Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release the drive belt tension by pushing the idler arm, then slide the belt off the idler pulley. Remove the mounting screw securing the old idler arm assembly and lift it out. Install the new W10837240 idler assembly, secure with the mounting screw, then re-route the drive belt around the new pulley and motor pulley. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the dryer is open, inspect the drum belt (WPW10112954) and drum support rollers for wear and replace if needed. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What does the idler pulley do? The idler pulley is a spring-tensioned wheel mounted on an arm and bracket inside the dryer. It presses against the drive belt to maintain the correct tension needed to keep the belt gripping the drum and motor pulley. Without proper tension, the belt slips, loses contact, or causes the drum to stop spinning. A worn or seized idler pulley is one of the most common causes of dryer squeaking and drum spin failure. Does W10837240 replace W10547287 and W10547290? Yes. The W10837240 is the updated part number that directly supersedes both the W10547287 and W10547290 idler pulley assemblies. If your dryer originally used either of those older part numbers, the W10837240 is the correct current replacement. How do I know if my lint screen is inside the door? Open the dryer door and look for a slot or housing just inside the door opening — typically at the top or bottom of the door opening — where you pull out the lint filter. If the filter pulls out from inside the door frame, the W10837240 is designed for your dryer style. If the lint screen pulls out from the top of the dryer cabinet, contact our support team with your model number to identify the correct idler pulley for your machine. Should I replace the drive belt at the same time? Yes — since the dryer is already disassembled to replace the idler pulley, it is highly recommended to also inspect and replace the drum belt (WPW10112954) at the same time. The belt and idler pulley wear together, and a worn belt on a new pulley — or vice versa — significantly shortens the life of the new part. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal to match the dimensions and performance of the original W10837240 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W10112954 Dryer Drum Belt Replaces WPW10112954 The XPARTCO W10112954 is an aftermarket replacement drum belt for Whirlpool and Maytag electric and gas dryers, and also fits select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. This belt circles the drum and attaches to the motor pulley, transferring the motor's rotation to keep the drum spinning and tumbling clothes evenly throughout the cycle. Measures approximately 92-1/2" long, flat design with 5 ribs and 4 grooves for a secure grip and smooth rotation. Over time, the belt can stretch, lose tension, or break from regular use and age. If your dryer's motor is running but the drum isn't turning, this belt has likely worn out or broken. Symptoms of a failing belt include the drum not spinning, unusual noises like squealing or rubbing, extended drying times, or unexpected stops mid-cycle. It directly replaces AP6015116, PS11748388, EAP11748388, and 1447719. Quick Answer The XPARTCO W10112954 Dryer Drum Belt fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers where the drum isn't spinning, or where you hear squealing/rubbing noise or notice extended drying times. Approximately 92-1/2" long, 5 ribs, 4 grooves. Replaces AP6015116, PS11748388, EAP11748388, 1447719. Since this is a bigger repair requiring the dryer to be mostly taken apart, it's a good time to also inspect or replace the idler pulley, which shares the same duty cycle as the belt. Common Problems This Part Fixes Motor runs but the drum won't turn Squealing or rubbing noise during operation Extended or inconsistent drying times Dryer stopping unexpectedly mid-cycle Belt stretched, loose, or visibly worn Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: WPW10112954, W10112954, 1447719, AP6015116, AWP48873, EAP11748388, PD00003553, PS11748388 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select Whirlpool electric and gas dryers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers built on the Whirlpool platform, including model numbers such as MED8000AG0, MED8000AW0, MGD6000XW0, MGD6000XW1, MGD6000XW2, MGD8000AG0, MGD8000AG1, MGD8000AW0, MGD8000AW1, 4KMEDC300BW0, 7MMGD0100TQ1, and MGD5500FC0. Note: Always verify your full model number before ordering, since Whirlpool uses several different belt lengths across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum belt (Made in USA) — circles the drum and attaches to the motor pulley Resolves "drum not spinning," "squealing or rubbing noise," and "extended drying time" symptoms Approximately 92-1/2" long, flat with 5 ribs and 4 grooves Direct drop-in replacement matching the original length and profile Replaces AP6015116, PS11748388, EAP11748388, and 1447719 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers Aftermarket replacement built to OEM-equivalent quality standards Requires basic hand tools and some dryer disassembly Product Specifications Part Number W10112954XP OEM Part Number WPW10112954 Part Type Dryer Drum Belt Condition Aftermarket Replacement Length Approx. 92-1/2" Profile Flat, 5 ribs, 4 grooves Function Transmits motor rotation to spin the drum Repair Difficulty Moderate — dryer largely disassembled for access Quantity 1 drum belt Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — This Is A Bigger Repair Requiring Significant Disassembly Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Replacing this belt is a larger project than some other dryer repairs, since it typically requires taking the dryer largely apart to access the drum, motor pulley, and idler pulley. Remove the top and front panels, then the drum, to reach the belt path. Release tension at the idler pulley and remove the old belt from the motor pulley and drum. Note the routing path before fully removing any remnants if the belt was broken. Feed the new W10112954 belt around the drum, then through the idler pulley and motor pulley, matching the original path exactly. Reinstall the drum, pull the belt tight, and re-tension the idler pulley. Rotate the drum by hand to confirm smooth movement before closing everything up. Reassemble the front and top panels. Restore power and run a test cycle to confirm quiet, smooth tumbling. Tools needed: nut driver, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer's motor runs but the drum won't turn. Is this the belt? Yes, this is the classic sign of a broken or badly worn drum belt. If the motor sounds like it's running normally but the drum stays still, the belt has likely stretched beyond its ability to grip, or has snapped and is no longer transmitting rotation from the motor to the drum. Should I replace the idler pulley at the same time as this belt? It's worth considering. Since replacing this belt requires a fair amount of disassembly to access the drum and pulley system, and the idler pulley shares the same duty cycle as the belt, one customer specifically ordered both together and reported a perfect fit for each. Replacing both at once can save you from needing to open the dryer back up again soon after if the pulley is also nearing the end of its life. Is this a difficult repair? It's more involved than some dryer repairs — one customer specifically noted that "replacing the dryer belt is a big project, need to take the whole thing apart." Basic hand tools like a nut driver and Phillips screwdriver are all that's required, but budget more time for this repair than a simple part swap. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, rib pattern, and groove design of the original WPW10112954 drum belt used in compatible Whirlpool, Maytag, and related electric and gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-16350V Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350V is an aftermarket replacement washer suspension rod kit (set of 4) compatible with select Samsung top-load washers in the WA48, WA50, WA52, and WA54 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer tub to the top of the washer cabinet, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. All four rods work together to keep the tub centered and stable — when one or more rods weaken, break, or lose their spring tension, the tub swings off-center and strikes the cabinet walls, causing violent shaking, banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the washer cabinet and internal components. Each rod is 27.5 inches in overall length and is constructed from spring steel with a plastic top cap and bottom cup that clip into the tub and cabinet mounting points. The kit includes all 4 suspension rods — always replace all four at the same time since the rods wear at the same rate. Installs in 20–30 minutes — no special tools required. Note: rods are coated with grease — wear gloves during installation. Quick Answer The XPARTCO DC97-16350V Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, display dc or UE imbalance error codes, or stop mid-cycle during spin. Set of 4 rods, 27.5" overall length, spring steel. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA48, WA50, WA52, and WA54 series. Replaces DC97-16350V, AP6975426, EAP12740434, PS12740434, ASM34760, PD00071611 Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod visible inside the cabinet Rattling or clunking noise during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350V, AP6975426, EAP12740434, PS12740434, ASM34760, PD00071611. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA48 series — WA48H7400AW, WA48H7400AP, WA48J7700AW, WA48J7770AP and related models Samsung WA50 series — WA50F9A6DSW, WA50F9A7DSP, WA50F9A7DSW, WA50F9A8DSP, WA50R5200AW, WA50R5400AV, WA50T5300AC and related models Samsung WA52 series — WA52A5500AV, WA52A5500AW, WA52A5500AC and related models Samsung WA54 series — WA54R7200AV, WA54R7200AW, WA54R7600AC, WA54R7600AV, WA54R7600AW, WA5AR7200AV and related models Samsung WA45 series — WA45H7000AW, WA45K7600AW, WA45M7050AW (select models) Kenmore / Sears top-load washers (select Samsung-built models) Important: Samsung uses several different suspension rod lengths across its top-load washer lineup. The DC97-16350V is 27.5 inches long and is for larger-capacity WA48–WA54 series models. Shorter-capacity models (WA40–WA45) typically use DC97-16350C or DC97-16350U rods. Always verify your model number before ordering to confirm you need the 27.5-inch version. Key Features Set of 4 suspension rods — complete replacement kit covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) 27.5 inches overall length — correct size for WA48, WA50, WA52, and WA54 series Samsung top-load washers Spring steel construction with plastic top cap and bottom cup — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement leads to uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350V, AP6975426, EAP12740434, PS12740434, ASM34760, PD00071611, and more Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350V Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA48, WA50, WA52, WA54 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 27.5 inches overall Material Spring steel / Plastic / Metal Color Black / Silver / Gray Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid of the washer and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of the old rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350V rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, then run a spin cycle to verify smooth, stable operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What do the suspension rods do? The suspension rods are spring-loaded shock absorbers that hang the outer washer tub from the top corners of the cabinet frame. They suspend the tub in the center of the cabinet and absorb the vibrations and movement generated during agitation and high-speed spin cycles. As long as all four rods have equal spring tension, the tub stays centered and stable. When one or more rods lose tension, stretch, or break, the tub is no longer held evenly and begins to swing off-center during spin — striking the cabinet walls, causing the loud banging, vibration, and imbalance error codes that indicate the rods need replacement. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly, which can cause the new rod to wear faster and may not fully resolve the vibration problem. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair in the near future. What do error codes dc and UE mean on Samsung washers? On Samsung top-load washers, error code dc (or sometimes dC) means the washer has detected an out-of-balance condition during the spin cycle and has stopped to prevent damage. Error code UE means an unbalanced load that the machine cannot automatically correct by redistributing. Both codes can be caused by an actual overloaded or unevenly distributed laundry load — but if the errors occur frequently even with normal loads and proper load distribution, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. How is the DC97-16350V different from DC97-16350U or DC97-16350S? The DC97-16350V, DC97-16350U, and DC97-16350S are all Samsung suspension rods, but they have different lengths for different washer model generations and capacities. The DC97-16350V is 27.5 inches long and is used on larger-capacity WA48–WA54 series Samsung washers. The DC97-16350U is approximately 26.4 inches and is used on mid-capacity WA45–WA50 series models. The DC97-16350S and DC97-16350C are shorter versions for earlier or smaller-capacity models. Using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Always verify your model number before ordering to confirm the correct rod length. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350V suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X23258 Dishwasher Genuine Circulation Pump Genuine dishwasher circulation pump designed to move water through the spray arms and restore proper wash performance. ✓ Genuine Part ✓ Replaces WD26X23258 ✓ Compatibility Support Product Description This Pump is a Genuine component for specific GE dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time. Replacing a faulty circulation pump can help restore proper water movement and improve dishwasher cleaning performance. Quick Answer If your dishwasher is not washing properly, has weak spray pressure, or makes unusual pump noise, the WD26X23258 circulation pump may need replacement. ⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dishwasher not cleaning dishes properly Weak spray arm water pressure Circulation pump noise Water not circulating during wash cycle Poor wash performance Replaces part Number WD26X23258, 4466766, WD26X22285, WD26X22518, WD26X22826, AGE25293, AP6039424, EAP11772000, PD00041691, PS11772000. Compatibility This part fits select GE, Hotpoint, Kenmore, and compatible dishwasher models using part number WD26X23258. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Key Features Genuine dishwasher circulation pump Helps restore proper water circulation Supports spray arm water pressure Designed for compatible dishwasher models Reliable replacement component Product Specifications Brand GE Part Type Dishwasher Circulation Pump Primary Part Number WD26X23258 Compatible Appliance Type Dishwasher Condition Genuine New Installation Disconnect power and water supply before installation. Inspect hoses and seals for leaks after installation. Troubleshooting Guide ⚠️ Disconnect power and water supply before servicing the dishwasher. Check spray arms for blockage before replacing the pump. Inspect pump area for leaks or unusual noise. Verify wiring connections are secure. Replace the circulation pump if water circulation problems continue. When Should You Replace This Part? Replace the dishwasher circulation pump if the dishwasher has poor cleaning performance, weak spray pressure, unusual pump noise, or water is not circulating during the wash cycle. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Genuine Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WH08X37938 Washer Lid Switch Assembly The XPARTCO WH08X37938 is an aftermarket replacement lid switch (lid lock) assembly for GE and Hotpoint top-load washers, also used on select Kenmore models. The assembly locks the lid while the washer is running and releases it when the cycle ends, and it tells the control board the lid is closed and it's safe to run. When it wears out, cracks, or fails electrically, the washer may refuse to start, stop in the middle of a cycle, show a lid or door lock error, or fail to lock the lid at all. This assembly replaces the original lock and switch as a unit, so you do not have to diagnose which internal contact has failed. It mounts on the washer cabinet with an electrical connector and is a straightforward repair, usually done in under an hour. Quick Answer The XPARTCO WH08X37938 Lid Switch Assembly fixes a GE or Hotpoint top-load washer that won't start, stops mid-cycle, won't lock the lid, or shows a lid or door lock error because the lid lock is worn or has failed. Complete replacement lock and switch assembly, aftermarket. Classic symptom: you close the lid and nothing happens, or the washer starts then stops and signals a lid or lock fault. Common Problems This Part Fixes Washer won't start when the lid is closed Washer stops partway through the wash, rinse, or spin Lid will not lock, or stays locked after the cycle ends Lid or door lock error codes Loose, cracked, or visibly damaged lid lock Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid switch assembly replaces the following part numbers: WH08X37938, WH08X32697, WH02X24399, WH08X32657, WH01X26694, WH01X24112, WH01X24114, WH01X26114, WH01X27954, WH08X31577, WH08X31222, 290D1580P001, 290D1580P002, 290D1580P003, 290D1580P004, 290D3070P001, EG-380843 M, AGE26076, AP7225583, EAP17626546, PD00087323, PS17626546 These are earlier GE numbers for the lid lock, as the part was updated over time. If your old lock or parts diagram shows any of them, match against this list. Compatibility This assembly is listed for select top-load washers from: GE and Hotpoint, including GTUN275EM0WW, GTUN275GM0WW, GTUP240EM0WW, and GTUP240EM2WW Kenmore, including 363.71542211, 363.71542310, and 363.71542410 Note: The model list above is only a sample, and lid locks differ between GE washer generations. Confirm fit by matching the number on your old lock or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This part is for top-load washers. Key Features Aftermarket replacement lid switch (lid lock) assembly Replaces the lock and switch as a unit, with no need to find the failed contact Restores starting, locking, and unlocking at the end of the cycle Cross-references to WH08X32697, WH08X31577, and other earlier GE numbers Fits select GE, Hotpoint, and Kenmore top-load washers Mounts on the cabinet with a plug-in electrical connector Product Specifications Part Number XPWH08X37938 OEM Part Number WH08X37938 Part Type Washer Lid Switch (Lid Lock) Assembly Condition Aftermarket Replacement Application Select GE, Hotpoint & Kenmore Top-Load Washers Installation Notes ⚠️ Unplug Power and Shut Off Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Open the lid and, following your model's service guide, remove the top panel or cabinet section to reach the lid lock mounted on the cabinet. Note the position of the old assembly, disconnect its wiring connector, and remove the screws holding it in place. Fit the new assembly in the same position, secure it, and reconnect the connector. Reassemble the washer, restore power and water, and run a short cycle to confirm the lid locks, the washer starts, and the lid releases at the end. Frequently Asked Questions My washer won't start with the lid closed. Is this the part I need? A failed lid lock is a common cause. The control board won't start a cycle unless it sees the lid is closed and locked. Check that the lid closes fully and that nothing is blocking it. If it still won't start, the lid lock is a likely cause. Is a lid switch the same as a lid lock? On these washers, the lid switch and lock are combined in one assembly, which this part replaces. My old part is marked WH08X32697 or WH08X31577. Will this work? Those numbers are on the Replaces list. Compare the connector and mounting against your old part, or contact our support team with your model number and we'll confirm. Will this fit my front-load washer? No. This is for top-load washers. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the GE WH08X37938. If you prefer a genuine OEM assembly, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11568627 Genuine OEM Whirlpool/Kenmore Dryer Drum Belt The W11568627 is a genuine OEM drum (cylinder) belt for select Whirlpool and Kenmore front-load dryers. This belt wraps around the outside of the drum and routes around the drive motor pulley and idler pulley — it's what actually spins the drum during a drying cycle while the motor and blower keep running independently. Over time this belt stretches, glazes, or cracks from heat and friction, and it eventually slips or snaps, leaving the drum motionless even though the rest of the dryer still runs. Manufactured by Whirlpool to factory spec for smooth, durable drum operation under high-demand drying cycles, this is a genuine OEM part — not an aftermarket equivalent — so fit and long-term performance match what came on the dryer originally. Quick Answer The Genuine OEM W11568627 Dryer Drum Belt fixes a Whirlpool or Kenmore dryer whose drum won't spin, or that runs with a rubbing/thumping noise from the drum area. Genuine OEM replacement, factory fit. Classic symptom: motor and airflow run normally, but the drum sits still — or a rubbing sound right before the belt fails completely. Common Problems This Part Fixes Dryer runs (motor and airflow work) but the drum doesn't spin Rubbing, squealing, or thumping noise from inside the dryer during operation Clothes bunch up in one spot instead of tumbling Burning rubber smell from a slipping or overheating belt Visible cracking, glazing, or fraying on the old belt Dryer drum spins freely by hand with no resistance from the motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part number: W11568627, W10577771, AP7175918, AWP45299, EAP16660508, OEM21527763, PD00070745, PS16660508 W10577771 is the previous Whirlpool part number for this belt; W11568627 is the current production number. We were not able to confirm additional cross-reference numbers beyond these two at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with the following Whirlpool and Kenmore dryer models: 11061632610, 11061632611 11061633610, 11061633611, 11061633612 11071632610, 11071633610, 110C61633610 WED9500EC0, WED9500EW0, WGD9500EC0, WGD9500EW0 Note: Not all applicable models are necessarily listed above — this is the compatibility data we were able to confirm from available sourcing, and Whirlpool may use this belt on additional models not shown here. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering. Key Features Genuine OEM drum belt — factory fit and durability, not an aftermarket equivalent Drives drum rotation during the drying cycle Built for smooth, reliable operation under high-demand drying cycles Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms Direct replacement for both W11568627 and the earlier W10577771 numbering One-year manufacturer replacement warranty on genuine parts Product Specifications Part Number W11568627 OEM Part Number W11568627 Part Type Dryer Drum (Cylinder) Belt Condition Genuine OEM Application Whirlpool & Kenmore Dryers Country of Origin Mexico Installation Notes ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's front or rear access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel. Frequently Asked Questions My dryer runs but the drum won't turn — is this the part I need? Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless. Is W10577771 the same belt as W11568627? Yes. W10577771 was the earlier Whirlpool part number for this belt; W11568627 is the current production number for the same design. If your dryer's parts diagram shows W10577771, this part is the correct current replacement. My exact model isn't listed — will this still fit? Possibly. Whirlpool uses this belt across a range of models beyond what's confirmed in our current compatibility data. Contact our support team with your full model number and we'll verify fit before you order. Do I need to replace the idler pulley at the same time? Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11130356 Washer Genuine Suspension Rod Kit Replaces Part Numbers: W11130356, W11027214, 4547230, W10594084, W10735787, W10821706, W10901058, W11033601, PD00042210, EAP12347543, AP6261900, PS12347543.

Read more less