XP61005518 Refrigerator Relay
Fits Specific refrigerator Models
Replaces Part Numbers: 12002782, 1194680, 61005518, AH2004057, EA2004057, OEM12028982, AP4009659, PS2004057.
Description: This is a Replacement compressor overload and relay kit for Specific Whirlpool, Maytag, Kenmore Refrigerator models. Kit was recently redesigned by manufacturer.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W11168740 Washer Water Valve (Cold Side)
The XPARTCO W11168740 is an aftermarket replacement cold water inlet valve for Whirlpool-built top-load washers, located on the top back of the cabinet where the hot and cold supply hoses connect. Unlike its companion hot-side valve (sold separately as W11168743, a single-solenoid design), this cold valve uses two internal solenoid coils in one blue-bodied housing. When the control calls for a cold fill, it energizes the appropriate solenoid to open the water path; once the correct level is reached, it closes again.
Because it's a dedicated cold-only valve, a failure here produces a distinctive symptom: cold-only fills stop working, slow down dramatically, or don't stop when they should, while hot fills (governed by the separate hot valve) continue working independently. Rated 120V, 60Hz, with push-on outlet connections sealed by rubber grommets. Common failure causes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn seal at the outlet connection. It directly replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, and PS12348073.
Quick Answer
The XPARTCO W11168740 Washer Water Valve (Cold Side) fixes Whirlpool-built top-load washers where cold water won't fill, fills slowly, keeps filling and won't stop, leaks, or throws a fill-related error code — while hot water fills normally. Blue-bodied, 2-solenoid cold-only valve, 120V, 60Hz, push-on outlet with rubber grommets. Replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, PS12348073. This is the cold-side valve only — the companion hot-side valve is sold separately as W11168743.
Common Problems This Part Fixes
Washer won't fill with cold water while hot water fills normally
Cold water fills much more slowly than it used to
Washer keeps filling with cold water and won't stop, leading to overfill
Water leaking at the cold connection point
Fill-related error code displayed on the control panel
Cycle stalling at the fill step and never advancing to wash
Cold wash or cold rinse cycles specifically affected while other cycles run fine
Water pooling underneath or behind the washer near the cold supply connection
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11168740, WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including:
Whirlpool top-load washers — WTW series
Maytag top-load washers (select Whirlpool-built models)
Select Kenmore top-load washers built on the Whirlpool platform
Verified model numbers include: WTW5500XL0, WTW5500XL2, and WTW5640XW3.
Note — cold side only: This is the cold water valve, identifiable by its blue body and two internal solenoids. The matching hot water valve for these same washers is sold separately under part number W11168743 — a single-solenoid design. The two are not interchangeable. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement dedicated cold water inlet valve for Whirlpool-built top-load washers
Two internal solenoid coils in one blue-bodied housing, identifiable at a glance from the single-solenoid hot valve
Resolves "won't fill with cold water," "fills slowly," "won't stop filling," and "leaking at the connection" symptoms caused by valve failure
Rated 120V, 60Hz
Push-on outlet connections sealed with rubber grommets
Approximately 3-3/8"L x 3-1/2"W x 2-3/8"H
Direct drop-in replacement — no modification required
Replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, and PS12348073
Compatible with a wide range of Whirlpool, Maytag, and Kenmore top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPW11168740
OEM Part Number
W11168740
Part Type
Washer Water Inlet Valve — Cold Side
Condition
Aftermarket Replacement
Application
Top-Load Washers (Whirlpool-Built)
Voltage
120V
Frequency
60 Hz
Solenoids
2 (dedicated cold water function)
Color
Blue / Teal / Black
Material
Plastic and metal
Outlet Connection
Push-on with rubber grommets
Dimensions
Approx. 3-3/8"L x 3-1/2"W x 2-3/8"H
Companion Part
W11168743 (hot water valve, sold separately)
Quantity
1 valve
Compatible Brands
Whirlpool, Maytag, Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply hose from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the screws securing the top panel (a 1/4" nut driver or socket handles most models), then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit next to each other and it's easy to cross a wire. Disconnect the electrical connector(s) from the old cold valve, disconnect the push-on outlet hose (check the rubber grommet for wear and replace it if it looks flattened or cracked), remove the two mounting screws holding the valve, and pull it free — leave the hot valve (W11168743) undisturbed if it isn't also being replaced. Install the new W11168740 in the same position, secure the mounting screws, reconnect the electrical connector(s), and press the outlet hose back onto its fitting with the grommet properly seated. Reattach the cold water supply hose, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm cold water fills at the normal rate, and stops when it should, with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, Phillips screwdriver, pliers, towel or shallow pan, work gloves.
Frequently Asked Questions
Cold water won't fill but hot water works fine. Is this the right part?
Yes — that's exactly the symptom pattern this valve addresses. Since your washer uses separate hot and cold valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve keeps working independently. If cold-specific cycles are the ones failing while hot cycles are unaffected, this cold-side valve is the correct part to replace.
How can I tell this valve apart from the hot-side valve just by looking at it?
This cold valve has a blue body and two internal solenoid coils, while the companion hot-side valve (W11168743) is a single-solenoid design. If you're staring at the old valve trying to confirm which one you're removing, the color and solenoid count are a quick visual check.
Do I need to replace both the hot and cold valves at the same time?
Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11168740 valve alone is sufficient. Some people choose to replace both while the top panel is already off, especially on an older washer, but it isn't required.
My washer keeps filling with cold water and won't stop. Is that dangerous?
It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dual-solenoid design, connection type, and dimensions of the original W11168740 cold water valve used in compatible Whirlpool, Maytag, and Kenmore top-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 2315549 Refrigerator Evaporator Fan Motor Replaces WP2315549
The XPARTCO 2315549 is an aftermarket replacement evaporator fan motor for Whirlpool-built side-by-side refrigerators, located in the freezer section. This small motor pulls cold air off the evaporator coil and pushes it through the duct system to both the freezer and fresh food compartments. Without it circulating air, the coil itself keeps getting cold, but that cold air never reaches your food — the freezer, being closest to the coil, may hold up reasonably well for a while, but the fresh food compartment depends entirely on ducted airflow and drifts warmer and warmer as circulation weakens or stops.
This motor ships complete with its wiring harness, so nothing needs to be spliced or transferred from the old unit. Common failure modes include worn motor bearings that let the blade wobble or bind, ice buildup on the coil that jams the blade, and electrical failure of the motor windings. A simple way to check before ordering: with the refrigerator unplugged, try turning the fan blade by hand — it should spin freely with no grinding or resistance. It directly replaces WP2315549, 2220569, 1193008, AP6007250, PS11740362, and EAP11740362.
Quick Answer
The XPARTCO 2315549 Refrigerator Evaporator Fan Motor fixes Whirlpool-built side-by-side refrigerators with uneven cooling between compartments, frost buildup on the evaporator coil, unusual humming or buzzing noise, or a fresh food section that runs warmer than the freezer. Includes wiring harness. Replaces WP2315549, 2220569, 1193008, AP6007250, PS11740362, EAP11740362. Double-check the part number carefully — this is a different motor from our similarly numbered 2315539 listing, and the two are easy to mix up.
Common Problems This Part Fixes
Fresh food compartment running warmer than the freezer, or warmer than it used to
Uneven temperatures between shelves or between the fresh food and freezer sides
Frost or ice buildup accumulating on or around the evaporator coil
Unusual humming, buzzing, or grinding noise coming from inside the freezer
Noise that stops when the freezer door is opened and starts again once it's closed
Refrigerator running constantly as the compressor tries to compensate for poor circulation
Fan blade that doesn't spin freely, or spins with noticeable resistance, when checked by hand
Fridge section too warm or too cold, freezer section too warm or too cold
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers:
2315549, WP2315549, 2220569, 1193008, AP6007250, PS11740362, EAP11740362, ESF-U2A
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This evaporator fan motor is compatible with select Whirlpool-built side-by-side refrigerators across the Whirlpool family of brands, including:
Whirlpool side-by-side refrigerators
Maytag, Amana, and KitchenAid refrigerators (select Whirlpool-built models)
Jenn-Air, Admiral, Norge, and Roper refrigerators (select models)
Inglis refrigerators (select models)
Select Kenmore and Ikea refrigerators built on the Whirlpool platform
Verified model numbers include: 7GS2FHAXTA02, 7GS5FHAXTA00, ED2DHEXWB00, and ED2DHEXWL00.
Note — easy to confuse with 2315539: This part is 2315549, production number ESF-U2A. It is a separate, distinct motor from our 2315539 listing (production number ESF-U2B, replacing 2219689, 2225625, and W10438708), which serves a different set of models. The two part numbers differ by only a single transposed digit and are frequently mistyped or mixed up when ordering — double-check your old motor's part number or your appliance's full model number carefully before ordering. Contact our support team with your model number if you're unsure which motor you need.
Key Features
Aftermarket replacement evaporator fan motor with wiring harness included — nothing to splice or transfer
Circulates cold air from the evaporator coil throughout the freezer and fresh food compartments
Resolves "fresh food too warm," "uneven cooling," "frost buildup," and "humming or buzzing noise" symptoms caused by fan motor failure
Direct drop-in replacement matching the original mounting and blade fitment
Replaces WP2315549, 2220569, 1193008, AP6007250, PS11740362, and EAP11740362
Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Admiral, Norge, Roper, Inglis, and select Kenmore refrigerators
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair — typically 15 to 30 minutes
Product Specifications
Part Number
2315549
OEM Part Number
WP2315549
Production Number
ESF-U2A
Part Type
Refrigerator Evaporator Fan Motor
Condition
Aftermarket Replacement
Brand
Whirlpool
Location
Freezer section, behind the rear panel near the evaporator coil
Kit Contents
Fan motor with wiring harness
Application
Side-by-Side Refrigerators
Repair Difficulty
Easy — 15 to 30 minutes
Quantity
1 fan motor
Compatible Brands
Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Admiral, Norge, Roper, Inglis, Kenmore
Installation Notes
⚠️ Unplug Refrigerator Before Starting — Let The Freezer Thaw If Iced Over Disconnect power at the outlet before beginning, and move all food from the freezer to a cooler for the duration of the repair. Wear work gloves. Access is through the freezer's rear interior panel: remove the shelving and bins as needed, then remove the screws securing the back panel and set it aside to expose the evaporator coil and fan assembly. If you see significant frost or ice buildup around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing — ice can be masking the actual failure and can make the old motor difficult to remove cleanly. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and carefully pull the motor and fan blade assembly free — on many models the blade is a separate piece that pulls off the motor shaft. Transfer the fan blade to the new motor if a blade isn't included, matching the original orientation. Mount the new 2315549 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the back panel. Restore power and monitor both compartments over the next 24 hours to confirm even cooling has returned. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
How is this different from your 2315539 listing? The numbers look almost identical.
They are genuinely different motors that happen to have nearly identical part numbers — 2315549 versus 2315539, just one transposed digit. This 2315549 motor carries production number ESF-U2A and replaces WP2315549, 2220569, and 1193008. Our separate 2315539 listing carries production number ESF-U2B and replaces a different set of numbers (2219689, 2225625, W10438708) for a different group of models. Because the numbers are so easy to mix up, we'd strongly recommend double-checking the exact number on your old motor, or your full refrigerator model number, before ordering either one.
My freezer seems fine but the fresh food section is warm. Is this the fan motor?
Yes, this is a very common and telling symptom pattern. The freezer compartment sits right next to the evaporator coil and can stay reasonably cold through simple proximity even with poor air circulation, but the fresh food compartment depends entirely on the fan pushing cold air through the ducting to reach it. When the fan motor fails or slows down, the fresh food side is usually the first and most noticeably affected area.
How can I test the motor before ordering a replacement?
With the refrigerator unplugged and the rear freezer panel removed, try turning the fan blade by hand. It should spin freely and smoothly with no grinding, binding, or resistance. If it doesn't turn freely, or doesn't turn at all, the motor has very likely failed. Also listen for humming or buzzing while the refrigerator is running — a motor trying and failing to turn often makes noise without actually moving air.
There's a lot of frost around the fan and coil. Should I address that first?
It's worth understanding which came first. Excess frost can be a cause of fan failure — a jammed, ice-bound blade can burn out the motor over time — or a result of it, since poor air circulation lets moisture condense and freeze unevenly around the coil area. Either way, thawing the ice out fully before installing the new motor makes the repair easier and lets you confirm the blade spins freely once everything is defrosted.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, wiring harness configuration, and airflow performance of the original WP2315549 evaporator fan motor used in compatible Whirlpool-built side-by-side refrigerators.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WR60X21887CM Refrigerator Evaporator Fan Motor
Fits specific GE refrigerator models.
Description: This Evaporator Fan Motor is replacement part for specific GE refrigerator models. It circulates air over the evaporator coils and throughout the refrigerator and freezer compartments, ensuring even cooling and maintaining the desired temperatures.
Replaces Part Numbers:WR60X21887, WR60X10240, 4324972, WR60X10054, WR60X10137, WR60X10189, AP5986488, PS11721928.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO WH12X10334 Washer Lid Switch with Wire Harness
The XPARTCO WH12X10334 is an aftermarket replacement washer lid switch assembly with wire harness compatible with select GE, Hotpoint, RCA, and Kenmore top-load washers — including the GTWN4250, GCWN4950, GTW180, GTWN2800, GTWN5550, GTUP270, and HSWP1000 series. The lid switch is a magnetic switch mounted near the lid hinge that detects whether the washer lid is open or closed. A magnet attached to the lid activates the switch when the lid closes — a small pin on the switch presses against an internal lever to signal the control board that it is safe to agitate or spin. This safety mechanism prevents the washer from running with the lid open.
When the lid switch fails, the washer may not start, may fill with water but not proceed to the wash cycle, may stop mid-cycle, may not spin or agitate even with the lid closed, or may display lid-related error codes on models with digital displays. This assembly includes the switch and attached wire harness. It directly replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, and PS1482372. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO WH12X10334 Washer Lid Switch fixes GE, Hotpoint, RCA, and Kenmore top-load washers that won't start, fill but don't proceed to wash, stop mid-cycle, or won't spin or agitate with the lid closed. Magnetic switch with wire harness — pin-and-lever design. Replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, PS1482372. Compatible with GE GTWN4250, GCWN4950, GTW180, GTWN2800, GTWN5550, GTUP270, and Hotpoint HSWP1000 series.
Common Problems This Part Fixes
Washer not starting — lid switch not signaling the lid is closed
Washer filling with water but not proceeding to the wash cycle
Washer stopping mid-cycle even though the lid is closed
Washer not agitating or spinning despite the lid being closed
Washer running intermittently — switch contact making and losing connection
Lid-related error codes displayed on models with digital control panels
Washer running with the lid open — switch stuck closed (less common but possible safety concern)
Replaces Part Numbers
This lid switch assembly directly replaces the following OEM and cross-reference part numbers:
WH12X10334, 1256927, AGE26415, AH1482372, AP3968471, EA1482372, EAP1482372, PD00001112, PS1482372
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This lid switch assembly is compatible with select top-load washers from the following brands and series:
GE top-load washers — GTWN4250D0WS, GTWN4250D1WS, GTWN4250M1WS series
GE top-load washers — GCWN4950D2WS series
GE top-load washers — GTW180SCJ0WW series
GE top-load washers — GTWN2800D0WW series
GE top-load washers — GTWN5550D0WW series
GE top-load washers — GTUP270EM4WW series
Hotpoint top-load washers — HSWP1000M4WW series
RCA top-load washers (select GE-built models)
Kenmore / Sears top-load washers (select GE-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Magnetic lid switch detects whether the washer lid is open or closed and signals the control board accordingly
Pin-and-lever design — the lid's magnet activates the switch, which presses an internal pin against a lever to confirm the lid is closed
Prevents the washer from agitating or spinning when the lid is open — important safety function
Includes pre-attached wire harness for direct connection to the washer's wiring
Replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, and PS1482372
Compatible with GE, Hotpoint, RCA, and Kenmore top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
WH12X10334
Part Type
Washer Lid Switch Assembly with Wire Harness
Condition
Aftermarket Replacement
Application
Top-Load Washers
Switch Type
Magnetic, pin-and-lever activation
Includes
Lid switch and attached wire harness
Compatible Brands
GE, Hotpoint, RCA, Kenmore
Installation Notes
⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The lid switch is located near the lid hinge area at the top of the washer cabinet. Use a putty knife to release the spring clips along the front edge of the top panel (or console, depending on model), then lift the top panel to access the switch from underneath. Locate the lid switch — it is typically mounted near the hinge or under the console. Photograph the wire connections before disconnecting. Disconnect the wire harness connector, or if your model requires it, cut and splice the wires using wire strippers and crimpers. Remove the mounting screws (typically a 1/4" nut driver) and remove the old switch. Install the new WH12X10334 switch in the same position, secure the mounting screws, and reconnect or re-splice the wire harness. Reinstall the top panel by aligning and pressing down until the spring clips engage. Restore power and test by closing the lid and starting a cycle to confirm the washer agitates and spins normally. You can test the old switch's continuity with a multimeter before removal to confirm it has failed. Tools needed: Putty knife, 1/4" nut driver, wire strippers, crimpers.
Frequently Asked Questions
What does the washer lid switch do?
The lid switch is a safety device that detects whether the washer lid is open or closed. A magnet attached to the underside of the lid activates the switch when the lid closes, which presses a small pin against an internal lever to send a signal to the control board confirming the lid is securely shut. The washer's control board uses this signal to allow agitation and spin — both of which are blocked whenever the lid is detected as open, as a safety measure to prevent injury from a spinning or moving basket.
My washer fills with water but won't start the wash cycle — is it the lid switch?
Yes — this is one of the most common lid switch failure symptoms. The washer is able to complete the fill phase because filling is typically not gated by the lid switch, but the agitation and spin phases require lid switch confirmation that the lid is closed. If the switch has failed and is not properly signaling lid closure, the washer fills normally but then stalls before agitating. According to repair technicians, when a washer fills and drains but does not agitate or spin, the lid switch is the first part that should be checked and is often the cause.
How do I test if the lid switch has failed?
Unplug the washer and access the switch as described in the installation notes. Disconnect the wire harness and set your multimeter to continuity or resistance mode. With the lid closed and the magnet engaging the switch pin, a working switch should show closed continuity. With the lid open (pin released), the switch should show open continuity. If the switch shows the same reading (either always open or always closed) regardless of lid position, the switch has failed and needs replacement.
Could a bad lid switch cause water filling and draining issues too?
In some specific cases, yes — some owners have reported resolving combinations of fill, drain, and spin issues by ultimately tracing the root cause back to a faulty lid switch, even after replacing other components like the water level pressure switch or control board. If you've already addressed other suspected causes for irregular cycle behavior and the symptoms persist, testing or replacing the lid switch is a low-cost troubleshooting step worth trying before assuming a major component (like the control board) needs replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the magnetic switch design and wire harness configuration of the original WH12X10334 lid switch assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE1M654 Dryer Timer Knob – Compatible with GE & Hotpoint Dryers
Product Description
Restore smooth and accurate cycle selection with the XPARTCO WE1M654 Dryer Timer Knob. This high-quality aftermarket replacement fits securely onto the dryer’s timer shaft, allowing easy turning and precise control of drying cycles. A cracked, loose, or missing knob can make it difficult to set cycles or operate the dryer properly. Replacing it with this durable XPARTCO knob restores normal operation and improves everyday usability.
XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price.
Replaces Part Numbers
WE1M654, 1264290, WE01M0443, WE1M443, WE1M502, WE1M668, AH1482197, EA1482197, PD00001146, EAP1482197, AP3995088, PS1482197.
Compatibility
This replacement dryer timer knob fits select GE and Hotpoint dryers.
Example compatible models include (but are not limited to):
GE GTDP220EF3WW, GTDP300EM1WS
Hotpoint HTDX100EM1WW
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and appearance
🎛️ Smooth Cycle Control – Restores easy and accurate timer adjustment
🧩 Direct-Fit Design – Push-on fit for secure installation
💪 Durable Plastic Construction – Built for everyday use
💰 Cost-Effective Repair – Affordable alternative to OEM knobs
📐 Product Specification
Part Number: WE1M654
Component Type: Dryer Timer Knob
Material: High-strength molded plastic
Color: White (OEM-style)
Mounting: Push-on / shaft-fit
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Ensure the dryer is powered off before installing the knob.
Basic Steps:
Turn the dryer off.
Align the new XPARTCO WE1M654 knob with the timer shaft.
Press firmly until fully seated.
Rotate to confirm smooth operation.
⏱️ Time Required: Under 2 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore smooth dryer control in seconds — Add to Cart Now for a quick, budget-friendly fix!
WH23X29538 (OE) Washer Water Valve
The WH23X29538 is an OE (Original Equipment) water inlet valve for GE front-load washers. This valve regulates the flow of water into the wash tub from the household supply line, with two water inlets (each with its own filter), four solenoid coils, and five water outlets working together to precisely control flow, temperature blending, and fill level throughout the cycle.
Rated 120V, 60Hz. Built with a stainless steel-reinforced, high-quality ABS plastic body for corrosion resistance and long-term sealing. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a range of symptoms: leaking or overflowing water, slow or irregular water filling, the washer filling non-stop or not filling at all, incorrect water temperature, or unusual noise during the fill cycle. It directly replaces WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225.
Quick Answer
The WH23X29538 (OE) Washer Water Valve fixes GE front-load washers with water leaking or overflowing, slow or irregular filling, non-stop filling, no water filling at all, incorrect water temperature, or unusual fill-cycle noise. 120V, 60Hz, 2 inlets with filters, 4 solenoid coils, 5 outlets. Replaces WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225. This valve is specific to the GFW550 series — it is a separate part from our WH23X29553 listing, which fits the GFW650/850 and PFW870/950 series.
Common Problems This Part Fixes
Water leaking or overflowing from the valve area
Slow or irregular water filling
Washer filling non-stop and not shutting off
Washer not filling with water at all
Incorrect water temperature during fill
Unusual noise during the water fill cycle
Error code related to water fill or temperature
What Is an OE Part?
OE (Original Equipment) means this part is manufactured by the same original supplier that produces the Genuine OEM version — identical fit, materials, and performance. The only difference is packaging: OE parts ship under our XPARTCO brand rather than the appliance manufacturer's branded box, which is why they can't be listed as Genuine OEM. You get factory-original quality at a more affordable price.
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water valve is compatible with select GE front-load washers, including model numbers such as:
GFW550SPN0DG, GFW550SPN1DG, GFW550SPN2DG, GFW550SPN3DG
GFW550SPR0RS, GFW550SPR3RS, GFW550SPR4RS, GFW550SPR5RS
GFW550SSN0WW, GFW550SSN1WW, GFW550SSN2WW, GFW550SSN3WW, GFW550SSN4WW, GFW550SSN5WW
Note — not the same as WH23X29553: This valve is specific to the GFW550 series. It is a separate part from our WH23X29553 listing, which fits the GFW650/850 and PFW870/950 series and has a completely different cross-reference set. The two are easy to confuse given the similar numbering — always confirm your exact part number before ordering. Contact our support team with your model number if you're unsure.
Key Features
OE (Original Equipment) water inlet valve — manufactured by the same supplier as the Genuine OEM version
Two water inlets with filters, four solenoid coils, five water outlets for precise fill control
Resolves "leaking/overflowing," "slow or irregular fill," "non-stop filling," "won't fill," and "wrong temperature" symptoms
ABS plastic body with stainless steel reinforcement for corrosion resistance
Rated 120V, 60Hz
Direct drop-in replacement — matches the original mounting and hose connections
Replaces WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225
Compatible with GE front-load washers in the GFW550 series
Product Specifications
Part Number
WH23X29538-OE
Designation
OE (Original Equipment)
Part Type
Washer Water Inlet Valve
Brand
GE
Application
Front-Load Washers (GFW550 Series)
Voltage
120V
Frequency
60 Hz
Inlets
2, each with a filter
Outlets
5
Solenoid Coils
4
Body Material
ABS plastic with stainless steel reinforcement
Quantity
1 valve
Compatible Brand
GE
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel or top of the cabinet, depending on your model. Have a towel or shallow pan ready, since residual water will spill out when you disconnect the lines. Photograph the wiring and hose connections before disconnecting anything — this valve has multiple inlets and outlets, and reconnecting one in the wrong position can cause a fill or temperature issue. Disconnect the water supply lines from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new WH23X29538 in the same position, reconnect all outlet hoses to their original positions exactly as photographed, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply lines, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm correct fill behavior and water temperature. Tools needed: Phillips screwdriver, pliers, towel or shallow pan, work gloves.
Frequently Asked Questions
My washer won't stop filling. Is that this valve?
Yes, this is one of the most common symptoms of a failing valve. A worn internal seal on one of the four solenoid coils can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it.
My water temperature seems off during the wash. Could this valve be the cause?
Yes. Because this valve has two separate inlets (hot and cold) and multiple solenoid coils that blend water to reach the correct temperature for each cycle setting, a fault in one of those coils can throw off the temperature blend even while the washer otherwise fills normally. This is a documented symptom this valve resolves.
Is this the same as WH23X29553? The numbers are very close.
No, these are two separate GE valve part numbers with completely different cross-reference sets and different compatible model series — this WH23X29538 serves the GFW550 series, while WH23X29553 serves the GFW650/850 and PFW870/950 series. Always confirm the exact part number from your washer's parts diagram rather than assuming based on a close number match.
Is this a genuine OEM part?
This is an OE (Original Equipment) part sold under our XPARTCO brand. OE parts are manufactured by the same original supplier that produces the Genuine OEM part, so the fit, materials, and performance are identical — the difference is that OE parts ship in XPARTCO packaging rather than the appliance manufacturer's branded box, which is why we can't list them as Genuine OEM. This gives you factory-original quality at a more affordable price than the branded version.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 6931EL3002M Dryer Blower Thermostat – Compatible with LG and Kenmore Dryers
Product Description
Restore proper temperature regulation in your dryer with the XPARTCO 6931EL3002M Dryer Blower Thermostat. This Dryer Blower Thermostat is a replacement part for select LG dryer models. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle. Common causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.
Replaces Part Numbers
6931EL3002M, 6931EL3002A, 6931EL3002K, PD00023476, EAP8747887, AP5782317, PS8747887.
Compatibility
This replacement blower thermostat (mounts on blower housing). fits select LG and Kenmore (manufactured by LG) dryers.
Example compatible models include (but are not limited to):LG DLE5977W, DLE3170W, DLEX3470V, and Kenmore 796.81022900.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM temperature control performance
🌡️ Accurate Temperature Regulation – Maintains proper blower housing heat levels. Thermostat 85C, 185F.
💰 Budget-Friendly Option – Provides OEM-level reliability at a lower price
🛠️ Easy Installation – Direct-fit design with standard mounting hardware
🛡️ Fixes Common Issues – Solves overheating, no-heat problems, long dry times, and auto-shutoff issues
📐 Product Specification
Part Number: 6931EL3002M
Component Type: Dryer Blower Thermostat
Material: Metal thermostat housing with bimetal sensor
Temperature Rating: Opens/closes at OEM-equivalent temperature thresholds
Mounting: Two-screw mounting to blower housing
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Always unplug the dryer before performing repairs to prevent electrical shock and injury.
Steps:
Disconnect power and remove the dryer’s rear access panel.
Locate the blower housing and identify the thermostat.
Remove the mounting screws and disconnect the wiring.
Install the new XPARTCO 6931EL3002M thermostat in the same position.
Reconnect wires, reinstall the panel, and restore power.
Run a test cycle to confirm proper temperature cycling.
⏱️ Time Required: 10–15 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore safe temperature control — Add to Cart Now for a reliable, cost-effective repair!
5303280326CM Washer Drive Belt
Washing machine belt, length 31 1/2”, width 1/2”, characteristics, medium “v”- shaped.
This Belt is for Older, Top-load Frigidaire Washer
Replaces Parts Numbers: 5303280326, 08004064, 133171, 144667, 144697, 3161152, 3235, 5303161152, 8004064, 8195-171, 8X318, ER5303280326, F000133171, F133171, F133171-000, F133171000, F144667-000, LB113, TJ5303280326, WH01X2630, WH07X0086, WH07X0098, WH1X2630, WH7X86, WH7X98, AP2142495, PS459613.
This is an aftermarket part that can be used as a replacement for the OEM part.
3405-001117 Genuine OEM Refrigerator Dispenser Control Switch - Compatible with Samsung
Product Description
Restore your refrigerator’s dispenser functionality with the 3405-001117 Genuine OEM Refrigerator Dispenser Control Switch. This Samsung-manufactured microswitch is designed for select Samsung refrigerators, controlling the activation of the water and ice dispenser mechanism. It ensures reliable dispensing, addressing issues like unresponsive or intermittent water/ice dispensing for a seamless user experience.
Note: Includes (1) dispenser control microswitch. Disconnect power before installation. Verify compatibility with your refrigerator model.
Replaces part numbers: 3405-001117, DA34-00011A, 110634, 3727507, PD00033242, EAP11712663, AP5962465, PS11712663.
Compatibility:
Compatible with select Samsung refrigerator models, including but not limited to:
Samsung: RS2530BBP, RS2530BSH, RS2530BWP, RS2555BB, RS2555SL, RS2555SW, RS2577BB, RS2577SL, RS2577SW, RS2630SH, RS2630WW, RS265LABP, RS265LAWP, RS277ACBP, RS277ACPN, RS277ACWP
Common models: Samsung RS253BABB, RS253BAVQ, RS255BABB, RS255BASB, RS257BARB
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung refrigerators with water and ice dispensers.
🔧 Specifications: Genuine OEM Samsung microswitch, single-pole, double-throw (SPDT), 0.1A, 125/250V.
💪 Reliable Performance: Ensures precise activation of the water and ice dispenser mechanism.
🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–20 minutes.
🛡️ Effective Fixes: Resolves unresponsive or intermittent water/ice dispensing issues.
Product Specification
Part Number: 3405-001117
Component Type: Refrigerator dispenser control switch
Material: Durable plastic housing with metal contacts
Operating Conditions: 0.1A, 125/250V, suitable for refrigerator dispenser environments
Compliance: UL-listed, Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the refrigerator from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator’s dispenser working smoothly today!
Add to cart now for a reliable fix!
54580301CM Dishwasher Drain Pump
120V, 60Hz
drain pump and housing assembly.
Fits Electrolux dishwashers.
Replaces Part Number: 154580301, 1257094, 154491301, AH1765174, EA1765174, AP4019644, PS1765174.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
