XPARTCO DC31-00187A Washer Drain Pump Motor
The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS.
This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected
Washer stopping mid-cycle due to a drain fault
Loud humming during the drain phase — motor energized but impeller not turning
Grinding or rattling during drain — damaged impeller or worn motor bearings
Clothes excessively wet after a cycle — pump not fully removing water before spin
Water draining very slowly — motor weakening below rated performance
Replaces Part Numbers
This drain pump motor directly replaces the following OEM and cross-reference part numbers:
DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series:
Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models)
Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models)
Samsung front-load washers — WF2 series (select models)
Samsung front-load washers — WF3 series (select models)
Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models)
Samsung front-load washers — WF5 series (select models)
Kenmore / Sears washers (select Samsung-built models)
Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement.
Key Features
Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump
Drives the pump impeller to expel water from the washer tub during the drain cycle
Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure
Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers
Duty cycle: 30 minutes on / 30 minutes off
Dimensions: 4-1/4"L x 3"W x 4-1/4"H
Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262
Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPDC31-00187A
Also Covers
DC31-00187D, DC31-00178A, DC31-00178D (variants)
Part Type
Washer Drain Pump Motor (Motor Only — reuses existing housing)
Condition
Aftermarket Replacement
Application
Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5)
Voltage
120V AC
Frequency
60 Hz
Wattage
80W
Amperage
1.1A
Duty Class
CL.F
Duty Cycle
30 minutes on / 30 minutes off
Dimensions
4-1/4"L x 3"W x 4-1/4"H
Color
Gray / White / Black
Material
Plastic / Metal / Rubber
Includes
Pump motor, impeller, O-ring
Error Codes Resolved
5C, SE, SC, 5E, SUDS
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves.
Frequently Asked Questions
What is the difference between DC31-00187A and DC97-20621C?
The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition.
What error codes indicate a drain pump motor failure?
Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement.
What is the difference between DC31-00187A and DC31-00178A?
These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs.
Should I clean the filter before replacing the pump motor?
Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 3406105 Dryer Door Switch Replaces WP3406105
The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open.
This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560.
Common Problems This Part Fixes
Dryer will not start at all — door switch not completing the circuit when door is closed
Dryer starts only when the door is slammed or held firmly closed
Dryer continues to run after the door is opened — switch not opening the circuit
Drum light not turning on when the door is opened (on models with drum light)
Dryer starts intermittently — door switch contact worn and making unreliable contact
Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear
Door switch visibly cracked, broken, or the actuator button no longer springs back
Replaces Part Numbers
This door switch directly replaces the following OEM and cross-reference part numbers:
WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is compatible with select gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers (gas and electric)
KitchenAid dryers
Amana dryers
Roper dryers
Estate dryers
Crosley dryers
Inglis dryers
Admiral dryers
Jenn-Air dryers
Magic Chef dryers
Norge dryers
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle
Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models
Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers
Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L
Stainless steel terminals and heat-resistant housing
Kit includes switch and 3-wire harness assembly — complete plug-in replacement
Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560
Compatible with 13 major appliance brands on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
3406105
OEM Part Number
WP3406105
Part Type
Dryer Door Switch Assembly (SPDT 3-Wire)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Switch Type
Single Pole, Double Throw (SPDT)
Wires
3-wire
Voltage
120-240V
Frequency
50-60Hz
Amperage
11A
Horsepower
1/3 HP
Switch Body Dimensions
1-3/4" L x 1-5/8" W x 1-1/4" H
Harness Length
7-3/4 inches
Color
Off-White / Black / Gray
Material
Plastic / Metal (stainless steel terminals)
Includes
Switch and 3-wire harness assembly
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife.
Frequently Asked Questions
What does the dryer door switch do?
The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit.
How do I test the door switch with a multimeter?
Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed.
What is the difference between 3406105 and 3406104?
The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement.
Why does this switch have 3 wires when my old switch only had 2?
The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WH41X22935 Washer Tub to Pump Hose
Washer Tub to Pump Hose
Replaces Part Number: WH41X22935, WH41X10163, 123C7981, 4258948, J27-763, WH41X0371, WH41X371, AP5983873, PS11721808.
Description: This Washer Tub to Pump Hose is a replacement part for select GE, Hotpoint Top-Load Washer models.
This is an aftermarket part that can be used as a replacement for the OEM part.
Genuine OEM WPW10605427 Washer Drain Pump
The Genuine OEM Whirlpool WPW10605427 is the washer drain pump for select Whirlpool, Maytag, Amana and Crosley washers. The drain pump removes wastewater from the washer during the drain portion of the cycle. When it fails, the washer may not drain, may leak near the pump, may make unusual noise, or may pump but not spin.
This is the original Whirlpool part, not an aftermarket equivalent. It replaces many earlier Whirlpool pump numbers, so the new pump may look different from your original. It is sold individually, without accessories or wire harnesses. Check your model number before ordering.
Quick Answer
The Genuine OEM WPW10605427 Drain Pump replaces the drain pump on a compatible Whirlpool, Maytag, Amana or Crosley washer when it has failed. Replaces W10605427, W10425238 and several other Whirlpool pump numbers. Classic symptoms: the washer won't drain, leaks, or makes unusual noise.
Common Problems This Part Fixes
Washer won't drain, or keeps water after the cycle
Water leaking near the pump
Unusual noises during draining
Washer pumps but won't spin
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drain pump replaces or supersedes the following part numbers:
WPW10605427 replaces WPW10425238, W10425238, W10605427, W10799064, W10799065, W10903216, W10918044, W10365896, B40-3A, AP6023357, AWP51154, EAP11756700, PD00038328, PS11756700
If your old pump shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This drain pump is listed for Whirlpool, Maytag, Amana and Crosley washers, including these examples:
Maytag MHW3000BW2, MHW3500FW0, MHW4300DC0, 7MMHW5500FW0
Whirlpool WFW87HEDC0, WFW95HEDC0, 7MWFW75HEFW0, 7MWFW90HEFW0
Crosley CFWH4084GW0
Note: The models above are a small sample of about 30 that retailers list, not a full list. Similar-looking pumps can differ in size and shape, so check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool part, not an aftermarket equivalent
Pumps wash water out of the washer during the drain cycle
Replaces many earlier Whirlpool drain pump numbers
Sold individually
Product Specifications
Part Number
WPW10605427
OEM Part Number
WPW10605427
Part Type
Washer Drain Pump
Condition
Genuine OEM
Manufacturer
Whirlpool
Quantity
1 Pump
Application
Select Whirlpool, Maytag, Amana & Crosley Washers
Installation Notes
⚠️ Unplug Power And Shut Off Water Before Installing Unplug the washer and turn off the water supply before you begin, and wear work gloves. The pump is at the bottom of the washer, and installation involves partially disassembling it, so moving the washer away from the wall helps. Remove the bottom or back panel and drain any remaining water. Disconnect the drain hose and electrical plug, remove the mounting bolts, and take out the old pump. Fit the new pump, reconnect the hose and plug, and refit the panel. Restore power and water and run a drain cycle, checking for leaks.
Frequently Asked Questions
My washer won't drain. Is this the part I need?
It can be, but a clogged hose or filter, or other parts, can cause the same symptom. Check for blockages first, and test the pump for continuity with a multimeter before replacing it. If the pump runs continuously, the water level switch may be the cause, so check that as well.
Is this an OEM or aftermarket part?
This is a genuine OEM part from Whirlpool, not an aftermarket equivalent.
Will the pump look the same as my old one?
Not necessarily. This pump replaces many earlier Whirlpool pump numbers, so it can look different from the original while still being the correct replacement. Match the part number and your model number.
Will this fit my washer?
It is listed for about 30 Whirlpool, Maytag, Amana and Crosley models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
154756401 Genuine Frigidaire Dishwasher Door Hinge Cable
The 154756401 is a Genuine OEM Frigidaire replacement dishwasher door hinge cable compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers. The door hinge cable runs through a pulley system at the base of the dishwasher door and is responsible for balancing and controlling the weight of the door as it opens and closes. When a cable breaks or frays, the door drops down suddenly and heavily, opening with a loud bang — or may not hold itself up at all, straining the door hinges and latch with every use.
This is a Genuine OEM part manufactured by Frigidaire to factory specifications and directly replaces the older 154578801. It is sold as a single cable — most Frigidaire dishwashers have two door hinge cables (one on each side), and it is strongly recommended to replace both at the same time. Installs in under 30 minutes with basic hand tools.
Quick Answer
The 154756401 Genuine Frigidaire Dishwasher Door Hinge Cable fixes dishwashers where the door drops open too fast, bangs loudly when opened, doesn't stay open at a comfortable angle, or where a broken cable is visible at the door hinges. Sold individually — replace both cables at the same time. Compatible with Frigidaire, Electrolux, Kenmore, Crosley, and Ikea dishwashers. Replaces 154578801.
Common Problems This Part Fixes
Dishwasher door drops suddenly and forcefully when opened — "slams" down instead of lowering gently
Loud banging or crashing noise when opening the dishwasher door
Door does not stay open at a horizontal position — drops all the way down
Broken, frayed, or snapped door cable visible near the door hinge or base of the door
Door hinge is being damaged or strained due to missing cable tension
Uneven door opening — one side drops faster than the other
Replaces Part Numbers
This door hinge cable directly replaces the following OEM and cross-reference part numbers:
154756401, 154578801, AFR14437, PD00082115, AP7212793, PS17217958.
154756401 is the current updated part number superseding the older 154578801. Contact our support team with your model number if you need compatibility confirmation before ordering.
Compatibility
This door hinge cable is compatible with select dishwashers from the following brands:
Frigidaire dishwashers
Electrolux dishwashers
Kenmore / Sears dishwashers (Frigidaire/Electrolux-built models)
Crosley dishwashers
Gibson dishwashers
Kelvinator dishwashers
Westinghouse dishwashers
Ikea dishwashers (select models)
Important: Most Frigidaire dishwashers use two door hinge cables — one on each side. This part is sold as a single cable. It is strongly recommended to replace both cables at the same time, as the second cable is likely to fail soon after the first.
Key Features
Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance
Balances and controls door weight as it opens and closes — prevents sudden door drops and hinge damage
Works in conjunction with the door pulley and spring system to provide smooth, controlled door movement
Current updated part number — directly supersedes 154578801
Sold individually — most models require two cables (one per side); replace both at the same time
Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers
DIY repair — installs in under 30 minutes with basic hand tools
Product Specifications
Part Number
154756401
Supersedes
154578801
Part Type
Dishwasher Door Hinge Cable
Condition
Genuine OEM
Application
Dishwashers
Material
Metal cable
Sold As
Single cable (most models require 2 — replace both at the same time)
Compatible Brands
Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, Ikea
Installation Notes
⚠️ Unplug Dishwasher Before Starting Disconnect power before beginning any repair. Open the dishwasher door and remove the inner door panel by unscrewing the screws around the perimeter of the inner door. With the inner panel removed, locate the door hinge cable routing — the cable runs from a bracket near the bottom of the door, through a pulley, and connects to the door spring tension system at the base of the dishwasher. Note how the cable is routed before removing the old one. Remove the broken cable by detaching it from the anchor points at each end. Thread the new 154756401 cable through the same pulley path and re-attach it to the anchor points at both ends, ensuring proper tension. Reinstall the inner door panel. Close and open the door to verify it moves smoothly and holds itself open horizontally. Restore power and run a short cycle to confirm normal operation. Tip: Replace both cables at the same time — the second cable will likely fail soon after the first. Tools needed: Phillips screwdriver, Torx screwdriver (T20), needle-nose pliers.
Frequently Asked Questions
What does the dishwasher door hinge cable do?
The door hinge cable is a tensioned metal cable that runs through a pulley and connects to the door spring system to balance the weight of the dishwasher door as it opens and closes. Without the cable, the full weight of the door would cause it to drop suddenly and forcefully when opened, slamming down onto the floor or straining the hinges with every use. The cable provides the controlled, counterbalanced movement that allows the door to lower gently and stay open at a horizontal position for easy loading and unloading.
How many door cables does my Frigidaire dishwasher have?
Most Frigidaire dishwashers use two door hinge cables — one on the left side and one on the right side of the door. This listing is for a single cable. When one cable breaks, the other is typically close behind since both cables have endured the same amount of use. It is strongly recommended to replace both cables at the same time while the door panel is already disassembled, saving you from repeating the repair shortly after.
What is the difference between 154756401 and 154578801?
These are the same door hinge cable. 154756401 is the current updated part number that superseded the older 154578801 during a production revision. If your dishwasher's parts diagram or old cable label shows 154578801, the 154756401 is the correct current replacement to order.
Is this compatible with Electrolux and Kenmore dishwashers?
Yes — Frigidaire and Electrolux are part of the same corporate family and share many components. The 154756401 cable is compatible with select Electrolux dishwashers and with Kenmore dishwashers built on the Frigidaire/Electrolux platform. Always verify your specific model number before ordering to confirm compatibility.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same door hinge cable installed in compatible Frigidaire, Electrolux, and related brand dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine Frigidaire OEM
Frigidaire 5304533220 Washer Water Fill Hose Assembly
Genuine OEM internal valve-to-tub fill hose for select Frigidaire-built laundry centers and washer/dryer combination units.
Product Overview
The Frigidaire 5304533220 Washer Water Fill Hose Assembly is a Genuine OEM internal fill hose used to route incoming water from the washer water inlet valve to the wash tub on compatible laundry-center models.
This is the valve-to-tub hose inside the appliance. It is not the external hot/cold household water-supply hose that connects the appliance to the wall faucets.
Quick Answer
5304533220 is the Genuine Frigidaire OEM valve-to-tub washer fill hose. It replaces earlier Frigidaire numbers 5304508358 and 809191901 and is used on select Frigidaire, Kenmore, Crosley, and other Electrolux-manufactured laundry centers.
Common Problems This Part May Fix
Water leaking inside the washer cabinet during fill
Cracked, split, hardened, or deteriorated fill hose
Leak between the inlet-valve outlet and wash tub
Loose or damaged internal water-fill connection
Water dripping from the valve-to-tub hose during operation
Replaces and Cross-References
5304533220, 5304508358, 809191901, AFR20016, AP7194866, EAP11775692, PD00076846, PS16745853
Cross-reference numbers are provided for identification. Always verify the full appliance model number before ordering.
Compatibility
Confirmed applications include select Frigidaire-built laundry centers and washer/dryer combinations such as:
FLCE7523AW0
FLCE7523AW1
FLCE7522AW1
FLCE7522AW4
FFLE3900UW0
FFLE3900UW1
FFLG3900UW0
FFLE3911QW1
CFLE3900UW0
41761712511
41761732810
41771732810
Important: This is only a partial compatibility list. Confirm the complete model number from the appliance rating label before purchase.
Key Features
Genuine Frigidaire OEM replacement part
Internal valve-to-tub fill hose
Routes fill water from the inlet valve to the washer tub
Direct replacement for 5304508358 and 809191901
Factory-style fit for compatible laundry centers
Used on select Frigidaire, Kenmore, and related Electrolux-built models
Product Specifications
Manufacturer Part Number
5304533220
Brand
Frigidaire
Part Type
Washer Internal Water Fill Hose
Hose Location
Water Inlet Valve to Wash Tub
OEM Status
Genuine OEM
Appliance Type
Laundry Center / Washer-Dryer Combo
Condition
New
External Supply Hose?
No — this is an internal appliance hose
Installation Notes
Disconnect electrical power to the appliance before service.
Shut off both household water-supply valves.
Access the washer inlet-valve and tub-fill connection according to the model-specific service procedure.
Place towels or a shallow pan below the hose connections to catch residual water.
Release the clamps and remove the old hose without damaging the valve outlet or tub fitting.
Install the new hose fully onto both fittings and reinstall the clamps in their original positions.
Restore water and inspect carefully for leaks before returning the appliance to service.
Diagnostic tip: If water is leaking during fill, inspect the hose, clamps, inlet valve, and tub connection before replacing parts. A leak from the external household supply hose requires a different part.
Frequently Asked Questions
Is 5304533220 a Genuine OEM part?
Yes. It is a Genuine Frigidaire OEM fill hose.
Does 5304533220 replace 5304508358?
Yes. 5304533220 supersedes 5304508358 and 809191901.
Is this the hose that connects the washer to the wall faucet?
No. This is an internal valve-to-tub fill hose located inside the laundry center.
Can this part correct a washer leak?
Yes, if the leak is caused by a cracked or damaged valve-to-tub fill hose or its connection. Inspect all nearby fittings and clamps before ordering.
Shop With Confidence
Verify your complete laundry-center model number before ordering. This listing is for the Genuine Frigidaire OEM internal valve-to-tub fill hose.
Genuine Frigidaire OEMValve-to-Tub Fill HoseCompatibility SupportFast U.S. Shipping
DC61-02432A Genuine OEM Samsung Washer Suspension Spring Guide
The DC61-02432A is a genuine Samsung OEM suspension spring guide (bracket) for Samsung and select Kenmore washers. This small but structurally important bracket connects the washer's outer frame to one of the suspension springs that support the wash tub, keeping the spring correctly seated and aligned as the tub moves during fill, wash, and especially spin. The tub itself hangs suspended inside the cabinet, and it's this network of springs and guides that lets it move and absorb vibration without banging against the surrounding frame or panels.
Because this guide holds the spring in its proper working position, a cracked, worn, or broken guide lets the spring drift out of alignment or lose tension where it seats. The result is usually excessive tub movement, unusual banging or knocking noises (especially during spin), or a washer that seems to "walk" or vibrate more than it used to. Left unaddressed, a spring that has come loose from a failed guide can allow the tub to strike the cabinet repeatedly, accelerating wear on nearby components. It directly replaces AP5581510, 2069491, and PS4206750. As a genuine OEM part, the DC61-02432A is manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The DC61-02432A Genuine OEM Samsung Washer Suspension Spring Guide fixes Samsung and select Kenmore washers with excessive tub movement, unusual banging or knocking noise (especially during spin), a washer that vibrates or "walks" more than it used to, or a suspension spring that has come loose or shifted out of position. Connects the washer frame to the suspension spring. Replaces AP5581510, 2069491, PS4206750. This bracket doesn't replace or include the spring itself — if the spring is stretched, rusted, or broken, it should be replaced separately alongside this guide.
Common Problems This Part Fixes
Excessive tub movement or vibration, especially noticeable during spin
Unusual banging, knocking, or thudding noise from inside the cabinet
Washer that vibrates more than it used to, or seems to "walk" across the floor during spin
Suspension spring that has come loose, shifted, or disconnected from its mounting point
Tub striking the cabinet frame or nearby panels during operation
Visible cracking or breakage on the guide/bracket where the spring attaches
Noise that has gradually worsened over time as the guide wears
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer suspension spring guide directly replaces the following OEM and cross-reference part numbers:
DC61-02432A, AP5581510, 2069491, ASM33826, PD00026723, PS4206750
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This suspension spring guide is compatible with select Samsung washers, and also fits select Kenmore washers built on the Samsung platform, including model numbers such as:
Samsung 402-49032012
Samsung 592-49006, 592-49032, 592-49042, 592-49045, 592-49052, 592-49075
Kenmore 40249032012
Note: This is the spring guide/bracket only — it does not include the suspension spring itself. If your spring is stretched, rusted, corroded, or broken, order the correct spring separately in addition to this guide. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Samsung OEM part — factory-specified bracket geometry and mounting fit
Connects the washer's outer frame to the suspension spring, keeping it correctly seated and aligned
Resolves "excessive tub movement," "banging or knocking noise," "washer vibrating or walking," and "loose spring" symptoms caused by guide failure
Direct drop-in replacement — mounts to the original frame attachment point
Simple, tool-light installation
Replaces AP5581510, 2069491, and PS4206750
Compatible with a range of Samsung and select Kenmore washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
DC61-02432A
Part Type
Washer Suspension Spring Guide / Bracket
Condition
Genuine OEM
Brand
Samsung
Function
Connects and aligns the washer frame to the suspension spring
Includes Spring
No — bracket/guide only, spring sold separately
Quantity
1 spring guide
Compatible Brands
Samsung, Kenmore
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Depending on your washer's design, you may need to remove the cabinet or rear access panel to reach the suspension spring and its guide bracket at the top of the tub assembly. Photograph how the old guide and spring are connected to the frame before removing anything, since suspension components are often symmetrical and easy to reverse or mismatch between mounting points. Carefully release the tension on the affected spring — depending on the model, this may involve unhooking the spring from the frame or the tub side first, then removing the old guide from its mounting point on the frame. Install the new DC61-02432A guide in the same position, then reattach the spring, making sure it seats fully and squarely in the new guide. Check any other springs and guides in the suspension system while you're in there, since if one has failed from age or wear, the others are often not far behind. Reassemble any panels you removed, restore power, and run a spin cycle to confirm the excessive movement, vibration, or banging noise has resolved. Tools needed: screwdriver (model-dependent access), pliers (helpful for spring tension), work gloves.
Frequently Asked Questions
My washer bangs loudly during spin. Is this the part I need?
It's a strong possibility, especially if the banging has developed gradually or seems to come from inside the cabinet near the tub. This guide keeps the suspension spring seated and aligned; when it cracks or wears out, the spring can shift out of position, letting the tub move more than it should and strike nearby components. Before ordering, it's worth opening up the access panel if you're comfortable doing so, to visually confirm whether a spring has come loose or a guide bracket looks cracked or broken.
Does this part include the suspension spring?
No — this is the guide/bracket only, which connects the frame to the spring. If your suspension spring itself is stretched, rusted, corroded, or snapped, you'll need to order the correct spring for your model separately in addition to this guide.
Should I replace just one guide, or check the others too?
It's worth inspecting the other suspension springs and guides while you have access, since they're typically all the same age and subject to the same wear. If one has failed, the others may not be far behind, and replacing them together can save you from repeating this repair again soon after.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It matches the original bracket geometry and mounting fit of the suspension spring guide originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W10518394 Genuine OEM Whirlpool Dishwasher Heating Element
The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades.
This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed.
Common Problems This Part Fixes
Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase
Wash water not getting hot enough — poor cleaning performance even with proper detergent
Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation
Heated dry cycle not working — no warm air at the end of the cycle
Element visibly burned through, broken, or showing arcing damage
Multimeter continuity test on the element shows an open circuit (no continuity)
Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element)
Detergent not fully dissolving — water too cool to activate the formulation
Replaces Part Numbers
This dishwasher heating element directly replaces the following OEM and cross-reference part numbers:
W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead.
Compatibility
This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including:
Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models
Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram)
Maytag dishwashers — select models (verify with parts diagram)
KitchenAid dishwashers — select models
Amana dishwashers — ADB1400AGW and related models
Kenmore / Sears dishwashers — select Whirlpool-built models
Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase
Rated 1200W for efficient heating and reliable temperature control
Oval-shape element approximately 15" L x 3" W x 3" H
Mounts in the bottom of the dishwasher tub, secured underneath with large nuts
Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement
Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times)
Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070
Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
W10518394
Part Type
Dishwasher Heating Element
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Shape
Oval (NOT interchangeable with horseshoe-style elements)
Wattage
1200W
Dimensions
Approximately 15" L x 3" W x 3" H
Mounting Location
Bottom of dishwasher tub
Related Parts (Sold Separately)
Rubber Washer (717273), Heater Nut (8268548)
Post-Install Step
Diagnostic reset required on most Whirlpool dishwashers
Compatible Brands
Whirlpool, Maytag, KitchenAid, Amana, Kenmore
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses.
Frequently Asked Questions
Why are my dishes coming out wet — is the heating element the cause?
Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed.
After installing the new element, the dishwasher still isn't heating — why?
On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well.
How is the W10518394 different from horseshoe-shape heating elements?
The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher.
Do I need to replace the rubber washers and nuts when installing this?
Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
80040 Washer Agitator Dogs – Compatible with Whirlpool, Kenmore, Maytag, Roper, and Crosley Washers
Product Description
Restore your washer’s cleaning performance with the 80040 Washer Agitator Dogs. These Washer Agitator Dog set is a set of 4 replacement parts for select Kenmore, Maytag, roper, Whirlpool washing machine models. These are the little plastic cams that allow the top of your agitator to spin freely in one direction but keep it from spinning in the opposite direction, giving you a "ratcheting" effect. If they are worn out, the top of your agitator will spin freely in both directions and your clothes won't get fully washed.
Replaces Part Numbers
80040, 285612, 285770, 3109, 3366877, 387091, 80040VP, 99989668, AH388034, EA388034, LP338, EAP388034, PD00002340, AP3119063, PS388034, TJ90LP338.
Compatibility
This replacement agitator dog kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and Amana top-load washers.
Example compatible models include (but are not limited to): Whirlpool WTW4800XQ2, Kenmore 110.82980100, and Maytag MVWC415EW1.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Designed to match OEM performance for Whirlpool-brand washers
⚙️ Restores Wash Action – Replaces worn agitator dogs for proper rotation and cleaning power
💪 Durable Nylon Design – Built for long-lasting use under heavy wash loads
🛠️ DIY Friendly – Installs easily with a socket wrench in minutes
🛡️ Fixes Common Issues – Solves slow or non-spinning upper agitator problems
📐 Product Specification
Part Number: 80040
Component Type: Washer Agitator Dogs (Set of 4)
Material: High-strength nylon
Mounting: Fits inside upper agitator cam assembly
Operating Conditions: Designed for top-load washers with dual agitators
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: 7/16-inch socket wrench, flathead screwdriver
⚠️ Safety First: Always unplug the washer before performing repairs to avoid electrical shock.
Steps:
Unplug the washer and remove the fabric softener dispenser and agitator cap.
Use a socket wrench to remove the bolt securing the agitator.
Lift off the upper agitator and remove the old agitator dogs.
Insert four new 80040 agitator dogs into the slots of the cam assembly.
Reassemble the agitator, tighten the bolt, and reinstall the dispenser cap.
⏱️ Time Required: 10–15 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🧰 Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore strong wash performance — Add to Cart Now for a reliable, budget-friendly replacement!
ERP WH01X10727 Washer Shock Absorber
Replaces Part Numbers: WH01X10727, 3029711, AP5793647, PS8756975.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO DC64-00828B Dryer Door Switch
The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open.
This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers.
Common Problems This Part Fixes
Dryer not starting even though the door is closed
Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently
Error codes dC, dF, dE, or d0 displayed on models with digital displays
Dryer continuing to run with the door open (unsafe failure mode — replace immediately)
Interior dryer light not turning on when the door is opened
Door switch button visibly broken, stuck, or not making the expected click when pressed
Multimeter test shows the switch fails to change state when actuated
Replaces Part Numbers
This door switch directly replaces the following OEM and cross-reference part numbers:
DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including:
Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related)
Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related)
Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related)
Samsung dryers — DV5 series (DV50K7500EW and related)
Samsung dryers — DVE series (DVE60M9900W and related electric models)
Samsung dryers — DVG series (DVG45N5300V and related gas models)
Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Safety switch that detects whether the dryer door is closed — required for the dryer to start and run
Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers
Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing
Durable plastic housing with metal contacts — withstands frequent door open/close cycles
Resolves Samsung door-related error codes including dC, dF, dE, and d0
Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436
Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
DC64-00828B
Also Replaces
DC64-00828A (prior version)
Part Type
Dryer Door Switch (Door Jamb Switch)
Condition
Aftermarket Replacement
Application
Electric and Gas Dryers (Samsung platform)
Dimensions
Approximately 1.73"L x 1.73"W x 0.47"H
Color
White
Material
Plastic / Metal
Error Codes Resolved
dC, dF, dE, d0 (door-related)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
What do error codes dC, dF, dE, and d0 mean on Samsung dryers?
These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage.
My dryer is running with the door open — what should I do?
A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer.
What is the difference between DC64-00828B and DC64-00828A?
These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing.
My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch?
Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
