WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch Replaces WB24X47186.
The WB24X25013 is a genuine GE OEM infinite control switch for a dual (bridge) surface element on GE, Hotpoint, and select Kenmore electric ranges — the kind of burner with an inner coil and an outer coil that can be run together for a large pot or as the inner coil alone for a small pan. Because it's governing two coil zones instead of one, this switch uses six terminal connections rather than the three or four found on a standard single-element infinite switch, and it mounts to the control panel with a distinctive figure-8 style shaft and two female mounting holes.
Like any infinite switch, it doesn't have fixed heat positions — instead it rapidly cycles power to the element(s) on and off at a ratio set by the knob, giving continuous heat adjustment from warm to high rather than a handful of steps. Rated for 240VAC at 15 amps. Over years of cycling, the internal contacts on a switch like this wear, pit, or weld together, and boilovers or spills can corrode the switch body and cause it to fail. A worn switch on a dual-element burner can produce an unusually wide symptom set: the whole burner may fail, or just the outer ring may stop responding while the inner coil still works, or the burner may stay on continuously regardless of the knob position. It directly replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832. As a genuine OEM part, the WB24X25013 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch fixes GE, Hotpoint, and Kenmore electric ranges with a dual (bridge) element burner where the burner won't turn on or off, only the outer ring fails to work while the inner coil still heats, the burner stays on continuously, or heat can't be adjusted. Six-terminal switch, figure-8 shaft, 240VAC / 15A. Replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, 4464832. Not the same switch as a standard single-element infinite switch — this one is specific to dual/bridge burners with an inner and outer coil.
Common Problems This Part Fixes
Dual-element burner won't turn on at all when the knob is turned
Outer ring of a dual/bridge element won't activate while the inner coil still works
Burner won't turn off — stays hot even with the knob at the off position
Burner stuck at one heat level regardless of where the knob is set
No ability to adjust temperature — always full blast or always low
Intermittent burner operation — works sometimes, not others
Knob feels loose, gritty, or doesn't turn smoothly through its range
Burner failure that followed a boilover or liquid spill on the control panel
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range surface burner infinite switch directly replaces the following OEM and cross-reference part numbers:
WB24X25013, WB24X47186, 191D4774P005, AGE1543754, AP7216136, PS11729102, PS17872685, EAP11729102, 4464832, 191D4774P005, MDSA-W767-GEM
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This dual-element infinite switch is compatible with select GE, Hotpoint, and Kenmore electric ranges equipped with a dual (bridge) surface element, including model families such as:
GE JB6, JB7, and JB8 series electric ranges (including JB630, JB640, JB645, and JB655)
GE JBS series electric ranges
GE JS6 and JS7 series electric ranges (including the JS760 series)
GE GRS and GRF series electric ranges
Hotpoint electric ranges (select GE-built models)
Select Kenmore electric ranges built on the GE platform
Verified model numbers include: JB645RK6SS, JS760EP6ES, JS760DP6WW, JS760SP7SS, JS760DP7WW, JS760SP6SS, JS760FP7DS, JS760FP6DS, JS760EP7ES, JB860EJAES, JB860FJADS, and GRS500PV1SS.
Note: This is a six-terminal switch built specifically for a dual (bridge) element with a figure-8 style shaft and two female mounting holes — it is NOT interchangeable with a standard single-element infinite switch such as the WB24T10029 or WB24T10025, which use fewer terminals and a different shaft profile. Fitting a standard single-element switch to a dual-element burner circuit will not correctly control both coil zones. Always verify your full model number and confirm the affected burner is a dual/bridge element before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified contact design for dual-element switching
Six-terminal design controls both the inner coil and outer ring of a dual (bridge) surface element
Figure-8 style shaft with two female mounting holes matched to the original control panel bracket
Infinite switch design allows continuous heat adjustment rather than a handful of fixed positions
Rated 240VAC at 15 amps
Resolves "burner won't turn on," "outer ring not working," "won't turn off," and "stuck at one heat level" symptoms caused by worn or corroded switch contacts
Direct drop-in replacement — mounts to the same control panel bracket and wiring harness
Replaces 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WB24X25013
Part Type
Range Surface Burner Infinite Switch (Dual/Bridge Element)
Condition
Genuine OEM
Brand
GE
Element Type Controlled
Dual (bridge) surface element — inner coil + outer ring
Terminal Connections
6
Shaft Style
Figure-8
Mounting
Two female mounting holes
Voltage
240VAC
Amperage
15A
Function
Cycles element power to allow continuous (infinite) heat adjustment across both coil zones
Quantity
1 switch
Compatible Brands
GE, Hotpoint, select Kenmore
Installation Notes
⚠️ 240V Circuit — Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning — this switch operates on a 240V circuit, and working on it while powered presents a serious shock hazard. Wear work gloves. Remove the burner knob (it typically pulls straight off, though some models use a small retaining clip) then remove the screws securing the control panel or backsplash to reach the switch from behind. Photograph the wiring before disconnecting anything — this is a six-terminal switch, and getting even one wire out of place can miswire the inner coil, the outer ring, or both. Label each wire as you remove it. Disconnect all six terminal connections from the old switch, then remove the mounting screws from the two mounting holes and pull the switch free from its figure-8 shaft opening. Install the new WB24X25013 in the same orientation, reconnect each of the six wires exactly as labeled, and secure the mounting hardware. Reinstall the control panel or backsplash, press the knob back onto the shaft, restore power, and test the burner at every knob position — confirm the inner coil and outer ring both activate correctly (together and, if your model supports it, with the outer ring switched off independently) before considering the repair complete. Tools needed: Phillips screwdriver, nut driver, wire terminal pliers (helpful but optional), work gloves.
Frequently Asked Questions
How do I know if my burner uses a dual-element switch like this one?
Look at the burner element itself: a dual (bridge) element has two distinct coil rings — a smaller inner coil and a larger outer ring — usually with a separate control or a knob position that lets you activate just the inner coil for a small pan or both rings together for a large pot. A standard single-ring element has only one coil and uses a simpler switch with fewer terminals. If your range has this two-ring burner design, the WB24X25013 (or the exact switch behind it) is the correct type — but always confirm your model number, since dual-element switches vary by range generation.
Only the outer ring of my dual burner doesn't work. Is it the switch or the element?
It could be either, and it's worth narrowing down before ordering. If the inner coil heats normally but the outer ring never activates at any knob position, check the outer ring element itself first — a broken element coil is a common and cheaper fix than a switch. If the outer ring element tests fine but the switch's six-terminal wiring specific to the outer coil circuit has failed or corroded, the infinite switch is the correct replacement.
Can I use a standard single-element infinite switch instead if this one is out of stock?
No. A standard single-element switch has fewer terminals and cannot correctly control the two separate coil zones of a dual (bridge) burner. Wiring a single-element switch into a dual-element circuit will leave one coil zone permanently uncontrolled or non-functional. Always order the six-terminal dual-element switch specified for your model.
What does "infinite switch" mean?
An infinite switch lets you dial in a continuous range of heat rather than a few fixed positions, by rapidly cycling the element's power on and off at a ratio set by the knob — low settings get short power pulses, high settings get long ones. When the internal contacts wear or weld together from years of cycling, the switch can get stuck feeding constant power (burner always hot) or stop switching at all (burner always off), regardless of where the knob is turned.
A spill got into the control panel and now the burner won't turn off. Is that the switch?
Very likely, yes. Liquid boilovers and spills are one of the most common causes of infinite switch failure — moisture gets into the switch body, corrodes or bridges the internal contacts, and the switch can end up stuck feeding power continuously even with the knob turned to off. If you suspect this, shut off power to the range immediately at the breaker rather than relying on the knob, since a shorted switch may not respond to it at all.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original six-terminal wiring, figure-8 shaft, 240VAC/15A electrical rating, and dual-coil switching behavior of the infinite switch originally installed for the dual (bridge) element in your GE, Hotpoint, or Kenmore range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 0130F00010 Gas Furnace Flame Sensor
Fits the Specific Goodman Gas Furnace models
Replaces Part Numbers:TJFLS013, AP6326767, 0130F00010
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO DG44-01002A Surface Element Infinite Switch
The XPARTCO DG44-01002A is an aftermarket replacement dual element infinite switch (energy regulator) for Samsung electric ranges. This switch does two jobs at once: it regulates how much electrical current reaches its surface element, which is what lets you dial in a precise heat level rather than just on/off, and it also controls the "hot surface" indicator light associated with that burner, letting you know when the element is still hot after use.
Over time, the internal contacts in this switch can wear, stick, or fail electrically. Because a single switch controls both functions, a failing switch can produce two very different-looking symptoms depending on which function is affected: the burner may stay stuck on high heat regardless of the dial setting, fail to produce any heat at all, or the hot surface indicator light may stay on for hours after the surface has completely cooled, even though the element itself tests fine. It directly replaces 2087510, MDSA-W21-SKM, MDSA-W888-UNM, MDSA-W888-UM, AP4337066, PS4240803, and EAP4240803.
Quick Answer
The XPARTCO DG44-01002A Surface Element Infinite Switch fixes Samsung electric ranges where a burner is stuck on high heat regardless of the dial setting, won't produce any heat at all, or the hot surface indicator light stays on for hours after the surface has cooled. Dual element design. Replaces 2087510, MDSA-W21-SKM, MDSA-W888-UNM, MDSA-W888-UM, AP4337066, PS4240803, EAP4240803. This switch controls both the element and its indicator light — if your indicator light won't turn off even though the burner is cool, this switch (not the element) is the cause.
Common Problems This Part Fixes
Burner stuck on high heat regardless of the dial setting
Burner won't produce any heat at all
Hot surface indicator light stays on for hours after the burner has completely cooled
Inconsistent heating — burner doesn't hold the selected temperature level
Unresponsive burner controls
Burner that heats erratically rather than at a steady, selected level
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range surface element infinite switch directly replaces the following OEM and cross-reference part numbers:
DG44-01002A, 2087510, , MDSA-W21-SKM, PS4240803, AP4337066, EAP4240803, ASM37999, PD00006793, 737534552513
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This infinite switch is compatible with select Samsung electric ranges in the FCQ3, FE71, FER3, FTQ3, and NE59 series, including model numbers such as NE59J3420 and NE59J4310.
Note: This is the switch, not the radiant heating element itself — the companion element is a separate part, DG47-00022A. If you're diagnosing a burner problem, it's worth testing both parts, since either one failing can cause similar symptoms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement dual element infinite switch (energy regulator)
Controls both the surface element's heat output and its hot surface indicator light
Resolves "stuck on high heat," "won't heat at all," and "indicator light stays on" symptoms caused by switch failure
Direct drop-in replacement — matches the original mounting and wire connections
Replaces 2087510, MDSA-W21-SKM, MDSA-W888-UNM, MDSA-W888-UM, AP4337066, PS4240803, and EAP4240803
Compatible with Samsung electric ranges in the FCQ3, FE71, FER3, FTQ3, and NE59 series
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair, typically 10 to 15 minutes
Product Specifications
Part Number
XPDG44-01002A
OEM Part Number
DG44-01002A
Part Type
Range Surface Element Infinite Switch (Energy Regulator)
Condition
Aftermarket Replacement
Brand
Samsung
Design
Dual element
Function
Regulates surface element heat output; controls hot surface indicator light
Related Part
DG47-00022A radiant element (sold separately)
Repair Difficulty
Easy — 10 to 15 minutes
Quantity
1 infinite switch
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Range Before Starting — Photograph Wiring Before Disconnecting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically from the rear of the control panel or the underside of the cooktop, depending on your model. Photograph the wiring connections on the old switch before disconnecting anything, since correct wire placement is essential for the switch to control the right burner and indicator light. Remove the screws securing the old switch, gently pry it out, and mark or note each wire's position for reference. Disconnect the wires from the old switch and remove it fully. Install the new DG44-01002A in the same position, reconnect each wire to its original terminal exactly as photographed, and secure the mounting screws. Restore power and test the burner across its full range of settings, confirming both the heat output and the indicator light behave correctly. Tools needed: screwdriver, pliers, pen or pencil for marking wires, work gloves.
Frequently Asked Questions
My hot surface light stays on for hours even though the burner has cooled down. Is this the switch?
Yes. This is a documented symptom specific to this switch, since it controls both the surface element and its indicator light together. If the light isn't going out even though the surface itself is cool to the touch, the switch — not the element — is the correct part to replace.
My burner is stuck on high heat no matter what setting I choose. Is that the switch or the element?
It could be either, so it's worth testing both with a multimeter before replacing. Test the radiant element first — it should read between 0 and 120 ohms if it's working correctly. Then test the infinite switch itself: remove it, connect a multimeter probe to each prong, and turn the switch to an on position. No continuity indicates the switch is the issue. Several customers have confirmed this exact symptom by swapping switches between two burners and watching the problem follow the switch, which is also a reliable way to isolate the cause if you have two dual-element burners.
Should I replace the element (DG47-00022A) at the same time?
Not necessarily, but it's worth testing both parts if you're not sure which one has failed, since a bad element and a bad switch can produce overlapping symptoms. If your multimeter tests confirm only the switch has failed, replacing just this part is sufficient.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the dual-element switching function, wire terminal configuration, and mounting design of the original DG44-01002A infinite switch used in compatible Samsung electric ranges.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WB03X24818CM Range Control Knob
Burner Knob.
Fits specific GE Gas Range models.
Replaces Part Numbers: WB03X24818, AP5989029, PS11729081.
Description: This Range Knob is a replacement part for specific GE ranges and oven models. It is used to control the temperature and settings of the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO AEZ73293801 Cooktop Burner Control Knob – Compatible with LG & Kenmore Cooktops
Product Description
Restore smooth, precise burner control with the XPARTCO AEZ73293801 Cooktop Burner Control Knob. This high-quality aftermarket replacement knob fits securely onto the burner control shaft, allowing accurate flame adjustment and dependable operation. A cracked, loose, or missing knob can make it difficult to control heat or safely operate your cooktop. Replacing it with this durable XPARTCO knob restores proper functionality and everyday cooking convenience.
XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price.
Replaces Part Numbers
AEZ73293801, EBZ60710601, 2025031, PD00055975, EAP3639420, AH3639420, EA3639420, AP5594929, PS3639420.
Compatibility
This replacement cooktop burner control knob fits select LG and Kenmore (LG-manufactured) gas cooktops and ranges.
Commonly used on surface burner controls.
Always verify your appliance’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches original fit and appearance
🎛️ Smooth Flame Control – Restores accurate burner adjustment
🧩 Direct-Fit Design – Push-on installation for secure seating
💪 Durable Plastic Construction – Built for daily kitchen use
💰 Cost-Effective Repair – Affordable alternative to OEM knobs
📐 Product Specification
Part Number: AEZ73293801
Component Type: Cooktop Burner Control Knob
Material: High-strength molded plastic
Color: Black (OEM-style)
Mounting: Push-on / shaft-fit
Application: Gas cooktop or range burner control
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Ensure the cooktop or range is turned off and cool before installing the knob.
Basic Steps:
Turn the burner control to the OFF position.
Align the new XPARTCO AEZ73293801 knob with the control shaft.
Press firmly until fully seated.
Rotate to confirm smooth operation.
⏱️ Time Required: Under 2 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore safe, precise burner control in seconds — Add to Cart Now for a quick, budget-friendly fix!
XPARTCO DG64-00472B Gas Range / Stove Burner Knob
Fits Specific Samsung Range / Cooktop models.
Replaces Part Numbers: DG64-00472B, DG64-00347B, 3555006, AP5949297, PS9865173.
Description: The Knob Assembly is a replacement Part designed for adjusting the temperature of specific Samsung surface burner models. It accepts a D-shaped shaft and is sold individually.
This is an aftermarket part that can be used as a replacement for the OEM part.
WB03X43926 Genuine OEM GE Range Surface Burner Control Knob Set
The WB03X43926 is a genuine GE OEM surface burner knob kit, including 5 stainless steel knobs for GE, Hotpoint, Haier, Monogram, and Café ranges. These are the knobs you turn to light and adjust each surface burner — each one fits onto a control shaft behind the panel, and its position controls the heat setting for that burner. Since this kit includes a full set of five, it's designed for replacing every burner knob on the range at once rather than mismatching a single new knob against several older, worn ones.
Over years of use, the finish on plastic-coated or stainless-finished knobs can crack, peel, or start to bubble, and the knobs themselves can become loose or worn at the point where they grip the control shaft. A full-set replacement gives your range a uniform, refreshed look while also resolving any individual knobs that have become difficult to turn or read. Weighing approximately 2.64 oz total, this kit requires no tools to install — each knob simply pulls straight off its post and the new one presses straight back on. It directly replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, and WB03K10294.
Quick Answer
The WB03X43926 Genuine OEM GE Range Surface Burner Control Knob Set fixes GE, Hotpoint, Haier, Monogram, and Café ranges with burner knobs that are cracked, peeling, bubbling, loose, or simply worn-looking after years of use. Set of 5 stainless steel knobs. Replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, WB03K10294. No tools required — each knob pulls straight off and the new one presses straight on.
Common Problems This Part Fixes
Burner knobs with cracked, peeling, or bubbling finish
Knobs that feel loose or wobbly on the control shaft
Knobs that are hard to read due to worn or faded markings
Mismatched or inconsistent-looking knobs across the range from replacing them one at a time
Knobs that have become difficult to turn smoothly
General wear after many years of daily cooking use
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range surface burner knob set directly replaces the following OEM and cross-reference part numbers:
WB03X43926, WB03K10303, WB03K10305, WB03K10208, WB03K10221, WB03K10294, AP7187858, OEM21563583, AGE21567, PD00074146
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This burner knob set is compatible with select GE ranges, and also fits select Hotpoint, Haier, Monogram, and Café ranges built on the GE platform.
Note: This is the stainless steel finish knob set. GE also sells a visually different black plastic knob (WB03T10236) for other range models — the two are not interchangeable, so confirm your original knob's finish and shaft style before ordering. Always verify your full model number before ordering, since GE uses several different knob designs across its range lineup. Contact our support team with your model number if you're unsure which knob set fits your range.
Key Features
Genuine GE OEM part — factory-specified fit and finish
Complete set of 5 stainless steel surface burner knobs for a uniform look across the range
Resolves "cracked or peeling finish," "loose knob," and "worn markings" symptoms
No tools required — pulls straight off the post, presses straight back on
Compatible with the same control shaft used across a range of GE-platform ranges
Replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, and WB03K10294
Compatible with GE, Hotpoint, Haier, Monogram, and Café ranges
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WB03X43926
Part Type
Range Surface Burner Control Knob Set
Condition
Genuine OEM
Brand
GE
Kit Contents
5 surface burner knobs
Finish
Stainless steel
Weight
Approx. 2.64 oz. (full set)
Mount Style
Push-fit onto control shaft
Repair Difficulty
Very Easy — no tools required
Quantity
1 set (5 knobs)
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Remove each old knob by pulling it straight off its post — on most models this requires no tools, just firm, even pressure. Align each new knob from the WB03X43926 set with its corresponding control panel position and indicator arrow, then press it firmly onto the post until it seats flush. Repeat for all five burner positions. There's no need to remove the knobs for normal baking, broiling, or self-clean use once installed. Restore power and test that each knob turns smoothly through its full range, with the markings lining up correctly against the indicator arrow at each setting. Tools needed: none.
Frequently Asked Questions
My knobs' finish is bubbling after many years. Is this the right fix?
Yes, this is a common wear pattern on older knobs — one customer described replacing 14-year-old knobs whose coating had started to bubble, and found the swap simple enough to do entirely by hand with no tools. If your knobs are showing this kind of surface wear, a full set replacement gives your range a consistent, refreshed look across all burners.
Do I need to remove these knobs before running a self-clean cycle?
No — these knobs are designed to be left in place during normal oven use, including self-clean cycles. One customer specifically noted using the self-clean feature without removing the knobs and had no issues.
Can I buy just one replacement knob instead of the full set of 5?
This particular listing is sold as a complete 5-knob set rather than individually. If only one knob has failed, you may still prefer the full set for a matching, uniform appearance across the range, especially if the remaining original knobs are also showing age. Contact our support team if you're looking for a single replacement knob instead.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original stainless steel finish, shaft fit, and marking layout of the surface burner knobs originally installed on your range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DG34-00027B Range Membrane Switch (Touchpad)
The XPARTCO DG34-00027B is an aftermarket replacement membrane switch touchpad for Samsung gas ranges. This is the keypad panel itself — the physical layer of touch-sensitive buttons you press to select temperature, set the time, and choose a cooking mode. Underneath a thin, durable overlay, this membrane switch reads each button press as a distinct signal and passes it along to the range's main control board, which then acts on the command. Unlike the main control board, this component doesn't process or execute anything on its own — it's purely the interface between your finger and the board.
Because of that division of labor, a failing membrane switch produces a very specific pattern that's easy to distinguish from a control board failure: certain buttons stop responding, specific functions become impossible to select, or particular settings can no longer be adjusted, while the rest of the panel — including the clock, display, and other buttons — continues working normally. If instead the entire display goes blank or the whole panel stops responding at once, that points to the main control board rather than this touchpad. It directly replaces DG34-00027A, AP5986689, and PS11735749.
Quick Answer
The XPARTCO DG34-00027B Range Membrane Switch (Touchpad) fixes Samsung gas ranges where certain buttons don't respond, specific functions can't be selected, or particular settings won't adjust — while the rest of the control panel, including the clock and display, still works normally. Replaces DG34-00027A, AP5986689, PS11735749. If the entire display is blank or completely unresponsive, or the clock works but no heating functions operate at all, the problem is more likely the main control board (such as our DE92-02588G listing) rather than this touchpad.
Common Problems This Part Fixes
Certain buttons on the control panel don't respond when pressed
Specific cooking functions or modes can't be selected
Particular temperature or time settings can't be adjusted
Some buttons work fine while others are unresponsive or intermittent
Touchpad feels unresponsive or requires repeated presses to register
Visible wear, cracking, or bubbling on the touchpad overlay surface
Buttons that used to work reliably have become inconsistent over time
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range membrane switch touchpad directly replaces the following OEM and cross-reference part numbers:
DG34-00027B, DG34-00027A, AP5986689, ASM912846, EAP11735749, PD00027535, PS11735749
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This membrane switch touchpad is compatible with select Samsung gas ranges, including model numbers such as:
NX58H5600SS
NX58J5600SG
NX58F5700WS
NX58M5600SB
Note: Samsung uses several similarly-numbered membrane switch touchpads across its range lineup — including DG34-00025A (for NX58F5300SS/NX58F5500SS/NX58F5500SB), DG34-00020A (for NE594R0/NE59J3420/NE59J3421), and DG96-00850H (for NE63A6511) — each for different model groups and not interchangeable with this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which touchpad fits your range.
Key Features
Aftermarket replacement membrane switch touchpad — the touch-sensitive keypad interface for the control panel
Resolves "certain buttons unresponsive," "can't select specific functions," and "settings won't adjust" symptoms caused by a worn or damaged membrane
Durable overlay material designed for long-term wear resistance
Smooth surface that's easy to clean and maintain
Direct drop-in replacement — matches the original control panel mounting
Replaces DG34-00027A, AP5986689, and PS11735749
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair with basic tools
Product Specifications
Part Number
XPDG34-00027B
OEM Part Number
DG34-00027B (also DG34-00027A)
Part Type
Range Membrane Switch (Touchpad)
Condition
Aftermarket Replacement
Application
Gas Ranges
Color
Black
Function
Touch-sensitive keypad interface; passes button signals to the main control board
Quantity
1 membrane switch touchpad
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Range Or Shut Off Breaker Before Starting — Small Parts, Keep Away From Children Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards. Wear work gloves. This part includes small components — keep them away from young children during installation. Access is typically through the front of the control panel: remove the screws or clips securing the panel trim, then carefully separate the old touchpad overlay from its mounting surface, since some models use an adhesive backing that may require gentle, even pressure to release cleanly without damaging the surrounding panel. Photograph the ribbon cable or connector routing before disconnecting anything. Disconnect the touchpad's ribbon cable or connector from the control board, and remove the old membrane switch fully. Position the new DG34-00027B so its buttons align correctly with the control panel cutout, press it into place evenly to seat any adhesive backing, and reconnect the ribbon cable or connector to the control board. Reinstall the panel trim and its screws or clips. Restore power and test every button on the touchpad to confirm each one now responds correctly. Tools needed: Phillips or flat-blade screwdriver (model-dependent), work gloves.
Frequently Asked Questions
Some buttons work but others don't. Is this the right part?
Yes, this is the classic symptom this touchpad addresses. Because the membrane switch is purely the physical button interface, individual sections of it can wear out or fail independently, leaving some buttons responsive while others stop working. If your clock, display, and some functions still work normally but specific buttons or settings don't respond, this touchpad — not the main control board — is the most likely cause.
My whole display is blank and nothing on the panel responds. Do I need this part?
Probably not. A completely blank or entirely unresponsive display points to the main control board rather than this touchpad, since the touchpad itself has no display and can't cause a total blackout on its own. Similarly, if your clock and timer work but no oven heating functions operate at all, that's also a control board symptom. This touchpad is the correct part specifically when some buttons or functions fail while the rest of the panel, including the display, continues working.
How do I know which specific membrane switch touchpad my range needs?
Samsung uses several different touchpads that look similar but serve different model groups — always check your full model number before ordering. This DG34-00027B fits NX58H5600SS, NX58J5600SG, NX58F5700WS, and NX58M5600SB specifically; other Samsung ranges use different part numbers such as DG34-00025A, DG34-00020A, or DG96-00850H. Contact our support team with your model number if you want to confirm before ordering.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the button layout, overlay material, and mounting configuration of the original DG34-00027B touchpad used in compatible Samsung gas ranges.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
DE92-02588G Genuine OEM Samsung Range Control Board
The DE92-02588G is a genuine Samsung OEM main control board and clock assembly for Samsung gas ranges. This board is the range's central processor for the oven side of the appliance — it monitors oven temperature, drives the heating functions, and includes the digital display that shows the time and temperature settings. Every button press on the control panel is interpreted here, and every heating command the oven executes is issued from this board.
Samsung's own service guidance draws a clear line for when this board is the correct part: order it when the range display is completely blank or unresponsive, or when the clock/timer still works but none of the oven's heating functions operate. It is specifically the wrong part when only certain buttons fail to respond or specific functions are missing while the rest of the panel works normally — that pattern points to a failed switch membrane (touchpad) instead, a separate component. Power surges, including lightning strikes near the home's electrical service, are a documented real-world cause of this board failing outright. It directly replaces AP5800586, 3553835, and PS8764724.
Quick Answer
The DE92-02588G Genuine OEM Samsung Range Control Board fixes Samsung gas ranges with a completely blank or unresponsive display, or a range where the clock/timer works but none of the oven's heating functions operate. Includes the digital clock/display. Replaces AP5800586, 3553835, PS8764724. Do NOT order this board if only certain buttons don't respond or specific functions are missing while everything else works — that points to a failed switch membrane (touchpad), not this board.
Common Problems This Part Fixes
Range display is completely blank or dead
Control panel is entirely unresponsive to any button press
Clock and timer function normally, but no oven heating functions work at all
Oven won't heat despite the range otherwise appearing to have power
SE or similar error code displayed on the control panel
Range that stopped working suddenly after a power surge or nearby lightning strike
Digital display showing incorrect or scrambled time/temperature readings
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range control board directly replaces the following OEM and cross-reference part numbers:
DE92-02588G, AP5800586, 3553835, EAP8764724, ASM553766, PD00025599, PS8764724
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This control board is compatible with select Samsung gas ranges, including model numbers such as:
NX58F5300SS, NX58F5300SW
NX58F5500SS, NX58F5500SW, NX58F5500SB
NX58R4311SS, NX58R4311SG
Note: Before ordering, confirm your symptom matches this board specifically. If the display is blank/dead, or the clock works but heating functions don't, this board is correct. If only some buttons or functions fail while others work fine, the issue is very likely the switch membrane (touchpad) instead — a separate part from this control board. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Samsung OEM part — factory-specified processor, relay, and display circuitry
Monitors oven temperature and drives all oven heating functions
Includes the digital clock/display for time and temperature readouts
Resolves "blank display," "unresponsive control panel," and "no heating functions" symptoms caused by control board failure
Direct drop-in replacement for the original board mounting and harness connectors
Replaces AP5800586, 3553835, and PS8764724
Genuine OEM replacement — guaranteed fit, materials, and performance
Straightforward repair — typically 15 to 45 minutes with basic tools
Product Specifications
Part Number
DE92-02588G
Part Type
Range Oven Main Control Board & Clock
Condition
Genuine OEM
Brand
Samsung
Application
Gas Ranges
Function
Monitors oven temperature, drives heating functions, digital clock/display
Repair Difficulty
Easy to Moderate — 15 to 45 minutes
Quantity
1 control board
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Range Or Shut Off Breaker Before Starting — Handle The Board By Its Edges Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards, and allow the range to cool if recently used. Wear work gloves. Access is typically through the rear of the control panel: remove the screws securing the back cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and getting one out of place will cause a no-start or miswired symptom. Handle the new board by its edges rather than touching the components directly, and avoid working on a carpeted surface or in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Install the new DE92-02588G in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Reinstall the rear cover, restore power, and test the display, clock, and all oven functions to confirm normal operation. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
Some of my buttons don't respond but others work fine. Do I need this board?
Probably not. Samsung's own guidance is specific here: if certain buttons don't respond, specific functions are missing, or you can't adjust particular settings while the rest of the panel works normally, that pattern points to a failed switch membrane (touchpad) rather than this main control board. This board is the correct part when the display is completely blank/dead, or when the clock and timer work but no heating functions operate at all.
My range stopped working right after a thunderstorm. Could that be related?
Yes, this is a documented real-world cause of this exact board failing. Power surges, including those from a nearby lightning strike, can damage the control board's circuitry outright, leading to a sudden and complete loss of function. If your range died abruptly during or shortly after a storm, this board is a strong candidate for the cause.
Should I replace the switch membrane at the same time, just in case?
Some people do replace both together, especially if they want to be certain the repair is complete on the first attempt rather than risk needing a second repair shortly after. But if your symptoms clearly match this board (blank display, or clock works with no heat) rather than the switch membrane's symptoms (some buttons unresponsive, others fine), replacing just this board is usually sufficient.
Does this board include the digital clock and display?
Yes. This is a combined control board and clock assembly — the digital display for time and temperature settings is part of this same board, not a separate component.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It includes the same processor, relay switching, and display circuitry as the control board originally installed in your range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
74009592CM Burner Control Knob
Black plastic burner knob
Fits Specific Maytag, Jenn Air, Whirlpool ranges
Replaces Part Numbers: WP74009592, 74009592, 1032643, 71003477, AP6011140, PS11744334.
Description: This Top Burner Control Knob is a replacement part for specific Whirlpool ranges and cooktop models. This part allows for precise control over the heat level of the stove's burners, enabling users to adjust the flame size for various cooking needs. Constructed from durable materials, the knob is designed to withstand the rigors of daily use, providing a reliable interface for setting and maintaining the desired cooking temperature.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO DG34-00025C Range Switch Membrane (Touchpad)
The XPARTCO DG34-00025C is an aftermarket replacement membrane switch touchpad for Samsung gas ranges. This is the keypad panel itself — the touch-sensitive overlay you press to select temperature, set the time, and choose oven or cooktop functions. When you press a button, the membrane switch reads that touch and transmits the signal to the range's main control board, which then activates the corresponding function. This touchpad doesn't process or execute anything on its own — it's purely the physical interface between your finger and the electronics behind the panel.
Because of that division of labor, a failing membrane switch produces a distinct pattern that's easy to tell apart from a control board failure: individual buttons or specific functions stop responding while the rest of the panel, including the clock and display, keeps working normally. If instead the entire display goes blank or the whole panel becomes unresponsive at once, that points to the range's main control board rather than this touchpad — for example, our DE92-02588G listing, which serves some of the same NX58R4311 models this touchpad fits. It directly replaces 4963022, AP6885265, PS12721647, and EAP12721647. As an aftermarket replacement, the DG34-00025C is built to OEM-equivalent quality standards.
Quick Answer
The XPARTCO DG34-00025C Range Switch Membrane (Touchpad) fixes Samsung gas ranges where certain buttons don't respond, specific functions can't be selected, or the panel behaves erratically — while the clock, display, and other buttons keep working normally. Replaces 4963022, AP6885265, PS12721647, EAP12721647. If the entire display is blank or completely unresponsive, the problem is more likely the main control board rather than this touchpad.
Common Problems This Part Fixes
Certain buttons on the control panel don't respond when pressed
Specific cooking functions or modes can't be selected
Panel behaves erratically — registers presses inconsistently or activates the wrong function
Some buttons work fine while others are unresponsive or intermittent
Touchpad requires repeated presses to register a command
Visible wear, cracking, or bubbling on the touchpad overlay surface
Buttons that used to work reliably have become inconsistent over time
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range switch membrane touchpad directly replaces the following OEM and cross-reference part numbers:
DG34-00025C, 4963022, AP6885265, ASM608484, EAP12721647, PD00066594, PS12721647.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This switch membrane touchpad is compatible with select Samsung gas ranges, including model numbers such as:
NX58R4311SS/AA, NX58R4311SS/AA-00, NX58R4311SS/AA-01
NX58R4311SG/AA, NX58R4311SG/AA-00, NX58R4311SG/AA-01, NX58R4311SG/AA-02
Note: Samsung uses several similarly-numbered membrane switch touchpads across its range lineup — including DG34-00025A (for NX58F5300SS/NX58F5500SS/NX58F5500SB), DG34-00027B (for NX58H5600SS/NX58J5600SG/NX58F5700WS/NX58M5600SB), DG34-00020A (for NE594R0/NE59J3420/NE59J3421), and DG96-00850E/DG96-00850H (for NX60A6111/NE63A6511) — each for different model groups and not interchangeable with this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which touchpad fits your range.
Key Features
Aftermarket replacement built to match Samsung's factory-specified button layout and overlay material
Touch-sensitive keypad interface that transmits button signals to the main control board
Resolves "certain buttons unresponsive," "can't select specific functions," and "erratic panel behavior" symptoms caused by a worn or damaged membrane
Waterproof overlay construction for durability against spills and cleaning
Direct drop-in replacement — matches the original control panel mounting
Replaces 4963022, AP6885265, PS12721647, and EAP12721647
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair with basic tools
Product Specifications
Part Number
DG34-00025C
OEM Part Number
DG34-00025C
Part Type
Range Switch Membrane (Touchpad)
Condition
Aftermarket Replacement
Brand
Samsung
Application
Gas Ranges
Color
Black
Construction
Waterproof overlay
Function
Touch-sensitive keypad interface; passes button signals to the main control board
Quantity
1 switch membrane touchpad
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Range Or Shut Off Breaker Before Starting — Small Parts, Keep Away From Children Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards. Wear work gloves. This part includes small components — keep them away from young children during installation. Access is typically through the front of the control panel: remove the screws or clips securing the panel trim, then carefully separate the old touchpad overlay from its mounting surface, since some models use an adhesive backing that may require gentle, even pressure to release cleanly without damaging the surrounding panel. Photograph the ribbon cable or connector routing before disconnecting anything. Disconnect the touchpad's ribbon cable or connector from the control board, and remove the old membrane switch fully. Position the new DG34-00025C so its buttons align correctly with the control panel cutout, press it into place evenly to seat any adhesive backing, and reconnect the ribbon cable or connector to the control board. Reinstall the panel trim and its screws or clips. Restore power and test every button on the touchpad to confirm each one now responds correctly. Tools needed: Phillips or flat-blade screwdriver (model-dependent), work gloves.
Frequently Asked Questions
Some buttons work but others don't. Is this the right part?
Yes, this is the classic symptom this touchpad addresses. Because the membrane switch is purely the physical button interface, individual sections of it can wear out or fail independently, leaving some buttons responsive while others stop working. If your clock, display, and some functions still work normally but specific buttons or settings don't respond, this touchpad — not the main control board — is the most likely cause.
My whole display is blank and nothing on the panel responds. Do I need this part?
Probably not. A completely blank or entirely unresponsive display points to the main control board rather than this touchpad, since the touchpad itself has no display and can't cause a total blackout on its own. This touchpad is the correct part specifically when some buttons or functions fail while the rest of the panel, including the display, continues working. Our DE92-02588G control board listing covers some of the same models this touchpad fits, in case that's the part you actually need.
How do I know which specific membrane switch touchpad my range needs?
Samsung uses several different touchpads that look similar but serve different model groups — always check your full model number before ordering. This DG34-00025C fits NX58R4311SS and NX58R4311SG specifically; other Samsung ranges use different part numbers such as DG34-00025A, DG34-00027B, DG34-00020A, or DG96-00850E/DG96-00850H. Contact our support team with your model number if you want to confirm before ordering.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the button layout, overlay material, and mounting configuration of the original DG34-00025C switch membrane used in compatible Samsung gas ranges.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM W11517331 Electric Range Surface Burner Control Knob
The Genuine OEM Whirlpool W11517331 is the surface burner control knob for select Whirlpool electric ranges. It mounts on the front panel and turns the burner on and off and adjusts the heat setting. Knobs wear out with age or get damaged, and a cracked, broken, loose or stripped knob, or one with the markings worn off, is the usual reason to replace it.
This is the original Whirlpool part, not an aftermarket equivalent. It is sold individually, one knob per order. Check your model number before ordering, because Whirlpool uses similar knobs in other finishes.
Quick Answer
The Genuine OEM W11517331 Surface Burner Control Knob replaces a worn or damaged burner knob on a compatible Whirlpool electric range. Replaces W10850027, W11117415 and W11458840. Classic symptoms: the knob is cracked, broken, loose or stripped, or the burner doesn't respond when you turn it.
Common Problems This Part Fixes
Cracked or broken knob
Knob stripped inside, so it spins without turning the burner control
Loose, misaligned or hard-to-turn knob
Knob markings worn off
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This burner control knob replaces or supersedes the following part numbers:
W11517331, W10850027, W11117415, W11458840, AP7002931, AWP46013, EAP16543518, PD00065443, PS16543518
If your old knob shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This burner control knob is listed for Whirlpool electric ranges, including these examples:
Whirlpool WEC310S0LS0, WEC310S0LS1, WEC310S0LS2, WEC310S0LS3
Whirlpool WEE515S0LS0, WEE515S0LV0, WEE515S0LZ0, WEE515SALS0
Whirlpool WEE745H0FE1, WEE745H0FH1, WEE745H0FS2, WEE745H0LZ0
Whirlpool WFE745H0FS2
Note: The models above are a sample, not a full list. Whirlpool sells similar knobs in other finishes under different part numbers, such as W11517334. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool part, not an aftermarket equivalent
Surface burner control knob that mounts on the range front panel
Replaces three earlier Whirlpool knob part numbers
Sold individually
Product Specifications
Part Number
W11517331
OEM Part Number
W11517331
Part Type
Electric Range Surface Burner Control Knob
Condition
Genuine OEM
Manufacturer
Whirlpool
Quantity
1 Knob
Application
Select Whirlpool Electric Ranges
Installation Notes
⚠️ Turn Off The Burner And Let It Cool Make sure all burners are off and cool. Pull the old knob straight off its spindle. Line up the new knob with the spindle and push it straight on until it is fully seated, then check that the off-position marking lines up and the burner responds. If the knob spins freely on a good spindle or the burner still doesn't respond, the burner switch may need replacing instead.
Frequently Asked Questions
My burner won't heat or start. Is a new knob the fix?
Sometimes. If the old knob is stripped, broken or loose, a new knob can fix it. If the knob is in good condition, the burner switch or element is more likely the cause, so check those before replacing the knob.
Is this an OEM or aftermarket part?
This is a genuine OEM part from Whirlpool, not an aftermarket equivalent.
Do I get one knob or a set?
One knob. If you need more than one burner knob replaced, order the quantity you need.
Will this fit my range?
It is listed for many Whirlpool electric ranges, but the model list above is only a sample and some models use a different knob. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
