Search results for "Gas Range Igniter"

XPARTCO DG34-00025C Range Switch Membrane (Touchpad) The XPARTCO DG34-00025C is an aftermarket replacement membrane switch touchpad for Samsung gas ranges. This is the keypad panel itself — the touch-sensitive overlay you press to select temperature, set the time, and choose oven or cooktop functions. When you press a button, the membrane switch reads that touch and transmits the signal to the range's main control board, which then activates the corresponding function. This touchpad doesn't process or execute anything on its own — it's purely the physical interface between your finger and the electronics behind the panel. Because of that division of labor, a failing membrane switch produces a distinct pattern that's easy to tell apart from a control board failure: individual buttons or specific functions stop responding while the rest of the panel, including the clock and display, keeps working normally. If instead the entire display goes blank or the whole panel becomes unresponsive at once, that points to the range's main control board rather than this touchpad — for example, our DE92-02588G listing, which serves some of the same NX58R4311 models this touchpad fits. It directly replaces 4963022, AP6885265, PS12721647, and EAP12721647. As an aftermarket replacement, the DG34-00025C is built to OEM-equivalent quality standards. Quick Answer The XPARTCO DG34-00025C Range Switch Membrane (Touchpad) fixes Samsung gas ranges where certain buttons don't respond, specific functions can't be selected, or the panel behaves erratically — while the clock, display, and other buttons keep working normally. Replaces 4963022, AP6885265, PS12721647, EAP12721647. If the entire display is blank or completely unresponsive, the problem is more likely the main control board rather than this touchpad. Common Problems This Part Fixes Certain buttons on the control panel don't respond when pressed Specific cooking functions or modes can't be selected Panel behaves erratically — registers presses inconsistently or activates the wrong function Some buttons work fine while others are unresponsive or intermittent Touchpad requires repeated presses to register a command Visible wear, cracking, or bubbling on the touchpad overlay surface Buttons that used to work reliably have become inconsistent over time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range switch membrane touchpad directly replaces the following OEM and cross-reference part numbers: DG34-00025C, 4963022, AP6885265, ASM608484, EAP12721647, PD00066594, PS12721647. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This switch membrane touchpad is compatible with select Samsung gas ranges, including model numbers such as: NX58R4311SS/AA, NX58R4311SS/AA-00, NX58R4311SS/AA-01 NX58R4311SG/AA, NX58R4311SG/AA-00, NX58R4311SG/AA-01, NX58R4311SG/AA-02 Note: Samsung uses several similarly-numbered membrane switch touchpads across its range lineup — including DG34-00025A (for NX58F5300SS/NX58F5500SS/NX58F5500SB), DG34-00027B (for NX58H5600SS/NX58J5600SG/NX58F5700WS/NX58M5600SB), DG34-00020A (for NE594R0/NE59J3420/NE59J3421), and DG96-00850E/DG96-00850H (for NX60A6111/NE63A6511) — each for different model groups and not interchangeable with this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which touchpad fits your range. Key Features Aftermarket replacement built to match Samsung's factory-specified button layout and overlay material Touch-sensitive keypad interface that transmits button signals to the main control board Resolves "certain buttons unresponsive," "can't select specific functions," and "erratic panel behavior" symptoms caused by a worn or damaged membrane Waterproof overlay construction for durability against spills and cleaning Direct drop-in replacement — matches the original control panel mounting Replaces 4963022, AP6885265, PS12721647, and EAP12721647 Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair with basic tools Product Specifications Part Number DG34-00025C OEM Part Number DG34-00025C Part Type Range Switch Membrane (Touchpad) Condition Aftermarket Replacement Brand Samsung Application Gas Ranges Color Black Construction Waterproof overlay Function Touch-sensitive keypad interface; passes button signals to the main control board Quantity 1 switch membrane touchpad Compatible Brand Samsung Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting — Small Parts, Keep Away From Children Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards. Wear work gloves. This part includes small components — keep them away from young children during installation. Access is typically through the front of the control panel: remove the screws or clips securing the panel trim, then carefully separate the old touchpad overlay from its mounting surface, since some models use an adhesive backing that may require gentle, even pressure to release cleanly without damaging the surrounding panel. Photograph the ribbon cable or connector routing before disconnecting anything. Disconnect the touchpad's ribbon cable or connector from the control board, and remove the old membrane switch fully. Position the new DG34-00025C so its buttons align correctly with the control panel cutout, press it into place evenly to seat any adhesive backing, and reconnect the ribbon cable or connector to the control board. Reinstall the panel trim and its screws or clips. Restore power and test every button on the touchpad to confirm each one now responds correctly. Tools needed: Phillips or flat-blade screwdriver (model-dependent), work gloves. Frequently Asked Questions Some buttons work but others don't. Is this the right part? Yes, this is the classic symptom this touchpad addresses. Because the membrane switch is purely the physical button interface, individual sections of it can wear out or fail independently, leaving some buttons responsive while others stop working. If your clock, display, and some functions still work normally but specific buttons or settings don't respond, this touchpad — not the main control board — is the most likely cause. My whole display is blank and nothing on the panel responds. Do I need this part? Probably not. A completely blank or entirely unresponsive display points to the main control board rather than this touchpad, since the touchpad itself has no display and can't cause a total blackout on its own. This touchpad is the correct part specifically when some buttons or functions fail while the rest of the panel, including the display, continues working. Our DE92-02588G control board listing covers some of the same models this touchpad fits, in case that's the part you actually need. How do I know which specific membrane switch touchpad my range needs? Samsung uses several different touchpads that look similar but serve different model groups — always check your full model number before ordering. This DG34-00025C fits NX58R4311SS and NX58R4311SG specifically; other Samsung ranges use different part numbers such as DG34-00025A, DG34-00027B, DG34-00020A, or DG96-00850E/DG96-00850H. Contact our support team with your model number if you want to confirm before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the button layout, overlay material, and mounting configuration of the original DG34-00025C switch membrane used in compatible Samsung gas ranges. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM W11517331 Electric Range Surface Burner Control Knob The Genuine OEM Whirlpool W11517331 is the surface burner control knob for select Whirlpool electric ranges. It mounts on the front panel and turns the burner on and off and adjusts the heat setting. Knobs wear out with age or get damaged, and a cracked, broken, loose or stripped knob, or one with the markings worn off, is the usual reason to replace it. This is the original Whirlpool part, not an aftermarket equivalent. It is sold individually, one knob per order. Check your model number before ordering, because Whirlpool uses similar knobs in other finishes. Quick Answer The Genuine OEM W11517331 Surface Burner Control Knob replaces a worn or damaged burner knob on a compatible Whirlpool electric range. Replaces W10850027, W11117415 and W11458840. Classic symptoms: the knob is cracked, broken, loose or stripped, or the burner doesn't respond when you turn it. Common Problems This Part Fixes Cracked or broken knob Knob stripped inside, so it spins without turning the burner control Loose, misaligned or hard-to-turn knob Knob markings worn off Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This burner control knob replaces or supersedes the following part numbers: W11517331, W10850027, W11117415, W11458840, AP7002931, AWP46013, EAP16543518, PD00065443, PS16543518 If your old knob shows a different number, contact our support team and we'll check whether it matches. Compatibility This burner control knob is listed for Whirlpool electric ranges, including these examples: Whirlpool WEC310S0LS0, WEC310S0LS1, WEC310S0LS2, WEC310S0LS3 Whirlpool WEE515S0LS0, WEE515S0LV0, WEE515S0LZ0, WEE515SALS0 Whirlpool WEE745H0FE1, WEE745H0FH1, WEE745H0FS2, WEE745H0LZ0 Whirlpool WFE745H0FS2 Note: The models above are a sample, not a full list. Whirlpool sells similar knobs in other finishes under different part numbers, such as W11517334. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Surface burner control knob that mounts on the range front panel Replaces three earlier Whirlpool knob part numbers Sold individually Product Specifications Part Number W11517331 OEM Part Number W11517331 Part Type Electric Range Surface Burner Control Knob Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Knob Application Select Whirlpool Electric Ranges Installation Notes ⚠️ Turn Off The Burner And Let It Cool Make sure all burners are off and cool. Pull the old knob straight off its spindle. Line up the new knob with the spindle and push it straight on until it is fully seated, then check that the off-position marking lines up and the burner responds. If the knob spins freely on a good spindle or the burner still doesn't respond, the burner switch may need replacing instead. Frequently Asked Questions My burner won't heat or start. Is a new knob the fix? Sometimes. If the old knob is stripped, broken or loose, a new knob can fix it. If the knob is in good condition, the burner switch or element is more likely the cause, so check those before replacing the knob. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Do I get one knob or a set? One knob. If you need more than one burner knob replaced, order the quantity you need. Will this fit my range? It is listed for many Whirlpool electric ranges, but the model list above is only a sample and some models use a different knob. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10415450 Genuine OEM Whirlpool Range Burner Knob The WPW10415450 is a genuine Whirlpool OEM surface burner control knob for gas ranges and cooktops. This is the knob you turn to light and adjust a surface burner — it fits onto a D-shaped valve stem behind the control panel, and its position controls how far the gas valve opens, from off through lite, hi, medium, and low. Markings printed around the perimeter line up with an indicator arrow on the control panel so you can see exactly what setting you've selected. Finished in stainless steel/chrome, approximately 2" in diameter. Over years of use, the knob's internal D-shaped socket can wear out and stop gripping the valve stem securely, or the knob itself can crack, melt slightly from heat exposure, or simply wear down from repeated turning. A worn or damaged knob typically shows up as difficulty adjusting the burner heat, a knob that feels loose or wobbly, a knob that spins without turning the valve, or one that no longer seats securely onto the shaft. It directly replaces W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, and PD00007159. Quick Answer The WPW10415450 Genuine OEM Whirlpool Range Burner Knob fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges with a burner knob that's cracked, loose, wobbly, spins without adjusting the flame, or won't seat onto the valve stem. Stainless steel/chrome finish, 2" diameter, fits a D-shaped shaft. Replaces W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, PD00007159. Visually similar knobs W10284885 and W10316664 are NOT compatible with this part despite looking alike. Common Problems This Part Fixes Difficulty turning or adjusting the burner heat setting Knob feels loose or wobbly on the shaft Knob spins freely without turning the gas valve Knob won't seat securely onto the valve stem Visible cracks, melting, or heat damage on the knob Knob missing entirely, making burner adjustment impossible Setting markings no longer line up correctly with the indicator arrow Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range burner control knob directly replaces the following OEM and cross-reference part numbers: WPW10415450, W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, AWP50229, PD00007159 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This burner knob is compatible with select Whirlpool gas ranges and cooktops, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea appliances built on the Whirlpool platform, including model numbers such as: GG388LXB01, GG388LXB02, GG388LXB03, GG388LXQ01, GG388LXQ02, GG388LXS04, GG388LXS05 GG390LXB01, GG390LXB03 GCG388LXQ03 GGG388LXB04, GGG388LXO04, GGG390LXQ01, GGG390LXS01, GGG390LXS02 Note — visually similar knobs are NOT compatible: Whirlpool uses several burner knobs that look nearly identical to this one but are not interchangeable, including W10284885 and W10316664. Same appearance does not mean same fit — these knobs use different internal shaft sockets and will not seat correctly on this valve stem. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which knob fits your range. Key Features Genuine Whirlpool OEM part — factory-specified D-shaft socket and setting markings Fits a D-shaped burner valve stem for a secure, non-slip grip Resolves "loose or wobbly knob," "spins without adjusting flame," "won't seat on the shaft," and "cracked or damaged knob" symptoms Stainless steel/chrome finish, approximately 2" diameter Clear off/lite/hi/med/low markings aligned to the control panel indicator arrow No tools required — simple pull-off, push-on installation Replaces W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, and PD00007159 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea gas ranges Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10415450 Part Type Range Surface Burner Control Knob Condition Genuine OEM Brand Whirlpool Application Gas Ranges and Cooktops Finish Chrome Diameter Approx. 2 in. Shaft Type D-shaped valve stem Settings Off, Lite, Hi, Med, Low Repair Difficulty Very Easy — no tools required Quantity 1 knob Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Pull the old knob straight off the valve stem — on most models this requires no tools, just firm, even pressure in the direction of the indicator arrow. Confirm the new WPW10415450 knob by checking that the part number matches before installing. Align the top of the new knob with the control panel's indicator arrow, then press the knob onto the D-shaped shaft until you feel and hear it click securely into place. Restore power and test that the knob turns smoothly through its full range, with the markings lining up correctly against the indicator arrow at each setting. Tools needed: none. Frequently Asked Questions My knob spins but doesn't seem to change the burner flame. Is this the right part? Yes, this is a common symptom of a worn knob. Over time, the internal D-shaped socket that grips the valve stem can wear out, letting the knob spin independently of the shaft instead of turning it. Replacing the knob restores that positive connection so turning it actually opens and closes the gas valve as expected. I found a knob online that looks identical but has a different part number. Will it work? Not necessarily, and this is worth being careful about. Whirlpool uses several burner knobs, including W10284885 and W10316664, that closely resemble this one visually but use different internal shaft sockets and are not compatible with this valve stem. Always match the exact part number rather than relying on appearance, and verify against your model number if you're unsure. Do I need any tools to replace this knob? No. This is a simple pull-off, push-on repair — remove the old knob by pulling it straight off the shaft, then press the new one on until it clicks into place. No screws, no disassembly of the control panel required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original D-shaft socket, finish, and setting markings of the burner knob originally installed on your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

S48D21 8" Range Surface Element Product Title Aftermarket S48D21 8" Range Surface Element - Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, Amana Electric Ranges Product Description Revive your electric range’s cooking performance with the Aftermarket S48D21 8" Range Surface Element from Parts-O-Matic. This high-quality aftermarket burner element replaces the original S48D21, delivering 2100 watts at 240V with a 4-turn coil design for efficient and even heating. Ideal for select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other brand electric ranges, it addresses issues like uneven heating, slow warm-up, or non-functional burners. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other electric range models. 🔥 Efficient Heating: 8" diameter, 4-turn coil delivers 2100 watts at 240V for consistent, even cooking. 💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Plug-in design with Y-style bracket; requires no tools and takes 5–10 minutes to install. 🛡️ Fixes Common Issues: Resolves uneven heating, slow warm-up, or burners that fail to heat. Compatibility: Compatible with models including but not limited to: Whirlpool: RF110AXSQ0, RF262LXSB, RF365PXKW0 Maytag: MER4110AAH, MER4120AAQ Kenmore: 629.4297, 629.60003600 (pre-2004 models) Jenn-Air: JES9750AAB Amana: AER5511AAQ Replaces part numbers: TJ90SP21MA, 14215226, 1938283, 309917, 403782, 404110, 406000, 814154, ERS48D21, SE302, SP21MA, SU214, SU302, TS4D8221, TS4D8221PB, TS4D8221SR, TS4D8221WI, YSP21MA, AP4503257. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Installation Notes: Tools Needed: None for standard installation; a flathead screwdriver may help for stubborn connections. Safety First: Unplug the range before installation to avoid electrical shock. Steps: Remove the old burner element by gently pulling it from the receptacle, align the Y-style bracket of the new S48D21 element, and plug it into the socket. Ensure the element sits flat in the drip pan. If the burner is not level, adjust the connection bolts to ensure they are parallel and push down gently. Installation takes 5–10 minutes. Note: A slight burning smell during first use is normal due to a protective coating; this will dissipate after 15–20 minutes. Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Restore your range’s cooking performance today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

XPARTCO 53-1096 Gas Dryer Thermostat - Compatible with Maytag, Amana, Magic Chef, Jenn-Air Dryers Product Description Keep your gas dryer safe and operational with the replacement 53-1096 Gas Dryer Thermostat. This high-limit thermostat is designed for select Maytag, Amana, Magic Chef, and Jenn-Air gas dryers, preventing overheating by shutting off the burner at 240°F and restarting at 200°F. It addresses issues like no heat, overheating, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat. Disconnect power and gas supply before installation. Often paired with thermal fuses (e.g., 53-1182, 53-0771) for comprehensive repairs. Replaces part numbers: WP53-1096, 53-1096, PD00055179, AP6009640, PS11742808. Compatibility: Compatible with models including but not limited to: Maytag: DG312, DG612, DG712, LDG7304AAL, LDG8604AAL, MDE3000AYW Amana: NGD7200TW10, 4GNED4400YQ2 Magic Chef: CYG1005AXX, CYG2000AWW Jenn-Air: JDE1000W, JDG1000W Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Maytag, Amana, Magic Chef, Jenn-Air, Norge, Admiral, and Crosley gas dryers. 🔥 Specifications: replacement high-limit thermostat, opens at 248°F, closes at 200°F, 25A at 240VAC. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, overheating, or premature shutoff issues. Product Specification Part Number: 53-1096 Component Type: High-limit thermostat Material: Metal and plastic Mounting: Two 1/4" male spade terminals, includes mounting bracket Operating Conditions: Suitable for high-temperature gas dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO W11366438 Range Surface Burner Knob Product Overview The XPARTCO W11366438 Range Surface Burner Knob is designed to control the heat level of your stove burners with precision. This high-quality replacement knob restores smooth operation and enhances the appearance of your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the W11366438 burner knob is likely worn out. Replacing it restores proper burner control and usability. Replaces Part Numbers Replaces OEM part number: W11366438, W11084623, 4929319, W11359382, W11505414, EAP12723935, AWP44385, PD00054489, AP6888134, PS12723935. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, and other compatible ranges. Whirlpool Ranges Maytag Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not engaging Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: XPW11366438 Part Type: Range Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Burner Control Troubleshooting Guide Knob spins freely → Worn insert Cannot adjust flame → Damaged knob Knob falls off → Cracked fitting When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or not functioning properly. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off and push the new knob firmly onto the control shaft. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, this knob is typically push-on and easy to install. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse Replaces WP8573713 The XPARTCO 8573713 is an aftermarket replacement thermal cut-off fuse for Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. This fuse is mounted on top of the burner funnel, directly under the drum, and it's a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant temperatures near the burner climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power. That's why a blown fuse produces such a specific symptom: the dryer won't heat, even though the drum may still tumble and the rest of the dryer seems to run normally. Because this fuse sits on the burner funnel underneath the drum rather than on the more accessible blower housing, replacing it is a more involved repair than a typical thermal fuse swap — the drum has to come out of the cabinet to reach it. Unlike a resettable thermostat, this fuse cannot be reset once it blows; it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat near the burner is exactly what this fuse is designed to react to. It directly replaces WP8573713, AP6013467, and PS11746693. Quick Answer The XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse fixes Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers that won't heat, even if the drum still tumbles normally. Mounted on the burner funnel under the drum. Replaces WP8573713, AP6013467, PS11746693. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer runs and tumbles but produces no heat Dryer that stopped heating suddenly, especially after running unusually hot Drying times that have gotten noticeably longer or clothes coming out damp Repeated blown fuses on a dryer with a known venting or airflow restriction Dryer that recently smelled like burning or overheating before losing heat Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas dryer thermal cut-off fuse directly replaces the following OEM and cross-reference part numbers: WP8573713, 1180872, 8573713, AP3866211, EAP990558, PS990558, AWP49233, PD00006618 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal cut-off fuse is compatible with select Whirlpool gas dryers, and also fits select Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers built on the Whirlpool platform, including model numbers such as WGD8500SR0, and Kenmore 11070372710 and 11071112020. Note: This fuse is specific to gas dryers, mounted on the burner funnel. It is not the same fuse used on electric dryer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement thermal cut-off fuse — one-time safety device that cuts power if the dryer overheats Mounted on top of the burner funnel, directly under the drum Resolves "runs but won't heat," "drying takes too long," and "clothes coming out damp" symptoms caused by a blown fuse Replaces WP8573713, AP6013467, and PS11746693 Compatible with Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8573713 OEM Part Number WP8573713 Part Type Gas Dryer Thermal Cut-Off Fuse Condition Aftermarket Replacement Application Gas Dryers Location Top of the burner funnel, under the drum Resettable No — one-time use, must be replaced once blown Material Plastic housing Dimensions Approx. 1"H x 1"W Repair Difficulty Moderate to Hard — drum removal required for access Quantity 1 thermal cut-off fuse Compatible Brands Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, Sears Canada Installation Notes ⚠️ Gas Safety — Shut Off The Gas Supply Before Starting This fuse sits directly on the burner funnel, close to the gas burner assembly. Before beginning, close the gas shutoff valve behind the dryer in addition to unplugging the dryer or shutting off its circuit breaker. If at any point you smell gas, stop immediately, leave the area, and do not operate any switches — contact your gas utility or a qualified technician. Do not attempt this repair if you are not comfortable working safely around a gas appliance's burner assembly; a qualified technician can complete it instead. ⚠️ Drum Removal Required — Inspect And Clean The Venting Before Reassembling Wear work gloves. This repair requires removing the drum from the dryer cabinet to access the burner funnel, so budget more time and disassembly than a typical thermal fuse swap. Remove the top and front panels according to your model's service diagram, disconnect the drive belt from the idler pulley, and lift the drum out of the cabinet to expose the burner funnel underneath. Photograph the wiring before disconnecting the old fuse's connectors. Test the old fuse for continuity with a multimeter to confirm it's actually blown (no continuity) rather than assuming, and test the new fuse to confirm it's good out of the box. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new 8573713 fuse on the burner funnel in the same mounting position, reconnect the wiring, and reassemble the drum, belt, and panels in reverse order. Restore the gas supply and power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer tumbles fine but there's no heat. Is this the right part? Yes, this is the classic symptom of a blown gas dryer thermal cut-off fuse. Because this fuse only interrupts the heating circuit and not the drive motor, the drum can continue tumbling completely normally while the dryer produces no heat at all. If you've confirmed the burner isn't igniting and the fuse tests as an open circuit, this is very likely the fix. Why does this repair require removing the drum? My other dryer's fuse didn't need that. This particular fuse is mounted on the burner funnel underneath the drum rather than on the blower housing at the back of the cabinet, which is where many thermal fuses on other platforms are located. Reaching the burner funnel requires taking the drum out of the cabinet, which is why this repair involves more disassembly than some other thermal fuse replacements. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and mounting configuration of the original WP8573713 thermal cut-off fuse used in compatible Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB03T10325 Range Surface Burner Control Knob Replaces Part Numbers: WB03T10325, 2691864, AP5690210, PS3510510. Description: This Range Knob is a replacement part for specific GE ranges and oven models. It is used to control the temperature and settings of the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 7733P410-60 Surface Burner Knob (Replaces WP7733P410-60) Product Overview The XPARTCO 7733P410-60 Surface Burner Knob (Replaces WP7733P410-60) is designed to control the heat level of your range’s surface burners. This durable replacement knob restores precise control and a clean, finished look to your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the 7733P410-60 burner knob is likely worn. Replacing it restores proper control of burner heat settings. Replaces Part Numbers Replaces OEM part number: WP7733P410-60, 7733P410-60, 74007733, WP7733P410-60VP, EAP11744702, AWP48511, PD00004326, AP6011505, PS11744702. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, Amana, and other compatible ranges. Whirlpool Ranges Maytag Ranges Amana Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not turning properly Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: 7733P410-60 Part Type: Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Cooktop Control Troubleshooting Guide Knob spins freely → Worn internal insert Cannot adjust flame → Damaged knob Knob falls off → Cracked or loose fit When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or no longer controls burner settings accurately. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off the control shaft and push the new knob firmly into place. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, most knobs are push-on and can be replaced without tools. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247 The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle. This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835. Common Problems This Part Fixes Dryer tumbles normally but produces no heat — element coil burned through Dryer takes significantly longer than usual to dry a load Clothes coming out damp or only partially dried at the end of a cycle Visible breakage in the element coil — snapped or burned-through Ni-Cr wire Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Multimeter continuity test on the element shows an open circuit Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands: DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit heating element is compatible with select electric dryers from multiple manufacturers: Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models) Whirlpool electric dryers (select models — see WP35001247 cross-reference) Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related) Amana electric dryers (NED7200TW10, YIED7200TW10 and related) Inglis electric dryers (select models) Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models) Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering. Key Features Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers Generates the heat that warms drying air — essential for the dryer to actually dry clothes Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time Insulators and restring already attached — ready for installation into the existing housing Rated 240V, 5300W — correct electrical specifications for compatible electric dryers Dimensions: 17"L x 6-1/2"W x 2-1/2"H Metal and ceramic construction — durable for repeated heat/cool cycles Electric dryers only — NOT compatible with gas dryer models Important: heating element assembly only — must reuse the housing/cannister from the old element Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XPDC47-00019A Also Replaces (Whirlpool-side) WP35001247, 35001247 Part Type Dryer Heating Element Assembly (Universal Fit) Condition Aftermarket Replacement Application Electric Dryers Only (NOT gas) Voltage 240V AC Wattage 5300W Terminal Connections 2 spade terminals Dimensions 17"L x 6-1/2"W x 2-1/2"H Material Metal / Ceramic / Ni-Cr coil wire Includes Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old) Compatible Brands Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions Does this really fit both Samsung AND Whirlpool dryers? Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering. Why do I need to reuse the housing from the old element? This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately. How do I know if the heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity). Should I replace the thermal fuse and thermostats at the same time? It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO HS810 Refrigerator 3-in-1 Hard Start Kit 1/12 to 1/5 HP 120V The XPARTCO XPHS810 is a universal 3-in-1 hard start kit that combines a solid-state starting relay, a start capacitor, and thermal overload protection into a single prewired unit for refrigerator and freezer compressors rated 1/12 to 1/5 HP at 120V (110–125VAC). It's designed as a direct equivalent to the widely used Supco RCO810 and similar kits, giving a struggling compressor extra starting torque to overcome internal friction and gas pressure at startup — commonly used to fix the classic "click-buzz-click" no-start symptom without replacing the entire compressor. The kit is fully prewired with color-coded leads (typically black = Common, white = Start, red = Run) and mounts directly onto the compressor's terminal pins, with instructions printed on the unit itself. It directly replaces Supco RCO810, URCO810, URC0810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, ERPU810, HS8, HS810, HS81, PCS810, and Mars 32781. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO HS810 3-in-1 Hard Start Kit fixes refrigerators and freezers whose compressor makes a repeated "click-buzz-click" sound and fails to start, or that shut off on thermal overload during startup. Combines relay, start capacitor, and overload protector in one prewired unit for 1/12 to 1/5 HP compressors, 120V, 3.5A RLA. Replaces Supco RCO810, URCO810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, HS8, HS810, HS81, PCS810, Mars 32781. Do not install on LG linear/inverter compressors — see Installation Notes. Common Problems This Part Fixes Compressor makes a repeated "click-buzz-click" noise and fails to start Refrigerator or freezer runs warm because the compressor won't stay running Compressor hums but doesn't start, then trips off on overload Refrigerator cycles on and off rapidly without reaching temperature Older or worn compressor that starts hard, especially after a power outage ⚠ Capacitor Hazard — Read Before Servicing This kit contains a start capacitor, which can store a dangerous electrical charge even after the refrigerator is unplugged. Always disconnect power before servicing, and discharge the capacitor safely (using an insulated-handle resistor tool or by briefly shorting the terminals with an insulated screwdriver) before handling it. Never touch capacitor terminals with bare hands. If you are not comfortable working around stored electrical charge, have this repair performed by a qualified technician. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This 3-in-1 hard start kit directly replaces the following OEM and cross-reference part numbers: XPHS810, RCO810, URCO810, URC0810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, ERPU810, HS8, HS810, HS81, PCS810, Mars 32781 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal hard start kit is compatible with refrigerator and freezer compressors in the following range: Compressors rated 1/12 HP through 1/5 HP 120V (110–125VAC) single-phase compressors Standard PSC (permanent split capacitor) and RSIR compressor types across Whirlpool, GE, Frigidaire, LG, Samsung, and most other major brands Important: Do NOT install this kit on LG linear/inverter compressors, or any compressor using a variable-speed inverter board (often labeled "Inverter," "Linear," "BLDC," or "Digital"). Connecting a standard hard start kit to an inverter-driven compressor can destroy the inverter control board. Check your compressor's label before ordering, or contact our support team with your model number if you're unsure. Key Features 3-in-1 design combines starting relay, start capacitor, and thermal overload protector in one prewired unit Delivers additional starting torque to help a struggling compressor overcome startup friction and gas pressure Resolves "click-buzz-click," "won't start," and "trips on overload" symptoms on eligible compressors Rated for 1/12 to 1/5 HP compressors at 120V, 3.5A RLA Prewired, color-coded leads with instructions printed on the unit for straightforward installation Can operate with or without an existing run capacitor Replaces Supco RCO810, URCO810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, HS8, HS810, HS81, PCS810, and Mars 32781 Aftermarket replacement built to OEM-equivalent quality and safety standards Product Specifications Part Number XPHS810 Equivalent To Supco RCO810 / RC0810 Part Type 3-in-1 Refrigerator/Freezer Hard Start Kit (Relay, Capacitor, Overload) Condition Aftermarket Replacement HP Range 1/12 to 1/5 HP Voltage 120V (110–125VAC) Current Rating 3.5A RLA Terminal / Wire Color Code Black = Common (C), White = Start (S), Red = Run (R) — typical; confirm against included diagram Not Compatible With LG linear/inverter compressors Installation Notes ⚠️ Unplug Refrigerator Before Starting — Discharge Capacitor Safely Disconnect power before beginning. Before touching any wiring, check your compressor's data label to confirm it is NOT a linear/inverter/BLDC compressor — this kit is not compatible with those and can damage the inverter board if connected. Access the compressor compartment, typically at the rear or bottom of the unit. Remove the existing relay/overload assembly by gently pulling it straight off the compressor terminal pins — do not force or twist. Use a multimeter to confirm which pins are Common (C), Start (S), and Run (R) if not already labeled. Connect the hard start kit's wires to the matching pins. Wire the kit's main power leads into the refrigerator's supply wiring using wire nuts, following the included diagram. Secure the kit with zip ties or its mounting strap to prevent vibration damage during compressor operation. Restore power and confirm the compressor starts smoothly without repeated clicking. Tools needed: nut driver or screwdriver, digital multimeter, wire nuts, insulated screwdriver (for capacitor discharge). Frequently Asked Questions My compressor makes a clicking or buzzing sound and won't start — will this fix it? A hard start kit resolves this in many cases, especially on older or worn compressors that struggle to overcome internal gas pressure at startup. However, "click-buzz-click" can also indicate a failing compressor winding or a compressor nearing end of life. If the hard start kit doesn't resolve the issue, the compressor itself may need replacement — a hard start kit can extend a marginal compressor's life but can't revive one with failed internal windings. Can I use this on any refrigerator? This kit works on standard PSC and RSIR compressors within the 1/12 to 1/5 HP range at 120V. It is NOT compatible with LG linear/inverter compressors or any variable-speed inverter-driven compressor — connecting it to one of those can destroy the inverter control board. Check your compressor's label for "Inverter," "Linear," "BLDC," or "Digital" before ordering. Do I need to remove my existing start capacitor or relay first? Yes — remove the old relay/overload assembly from the compressor terminal pins before installing this kit. The XPHS810 is designed to work with or without an existing separate run capacitor remaining in the circuit, but the old start relay and any old start capacitor should be removed and replaced by this kit, not left in place alongside it. Is this safe to install myself? Many DIYers install hard start kits successfully, but this repair involves a capacitor that can hold a dangerous electrical charge even after the unit is unplugged, plus correctly identifying compressor terminals. If you're not comfortable working around stored electrical charge or don't have a multimeter to confirm terminal identification, we'd recommend having a qualified technician perform this repair. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE1X21975 Dryer Fuse, 30 Amp The XPARTCO WE1X21975 is a 30 Amp, 250 Volt ceramic thermal fuse used in GE dryers as a safety cutoff component. It's wired into the heating circuit and monitors the dryer's operating temperature — if the unit overheats due to restricted airflow, a failing thermostat, or a clogged exhaust vent, this fuse blows and cuts power to the heating circuit (or the entire unit, depending on the model's wiring) to prevent overheating damage or a fire hazard. Unlike a resettable thermostat, this is a one-time safety device: once it blows, it must be replaced — it cannot be reset. A blown thermal fuse is one of the most common reasons a GE dryer runs but produces no heat, or in some wiring configurations won't start at all and clicks when the start button is pressed. Because this fuse is a safety-critical protection device, it's worth also checking and clearing the cause of the overheating (lint buildup, a crushed or clogged exhaust duct, or a failed cycling thermostat) at the same time you replace it — otherwise the new fuse is likely to blow again. Quick Answer The XPARTCO WE1X21975 Dryer Fuse fixes a GE dryer that runs with no heat, or shuts off mid-cycle after getting hot. 30 Amp / 250 Volt ceramic thermal fuse, direct OEM fit and function. Classic symptom: dryer tumbles fine but clothes come out cold, or the dryer clicks and won't start. Always clear the cause of overheating (lint, vent restriction, or a failed thermostat) when replacing this fuse. Common Problems This Part Fixes Dryer runs and tumbles but produces no heat Dryer starts, heats briefly, then shuts off mid-cycle Dryer won't start at all — clicking sound when the start button is pressed Dryer stops running entirely after the unit has overheated Clothes come out damp or cold after a full cycle Dryer previously showed signs of overheating (hot exterior, burning smell) before losing heat Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermal fuse directly replaces the following part numbers: WE1X21975, 4248223, AGE25250, AP5957584, EAP10065161, PD00030077, PS10065161, 14QBP30CFB, 3AB, 6AB, SP, RABC, 314, ABC, CES-2, CES-4 Some listings also reference the earlier GE part number 4248223, which appears to correspond to the same fuse design. We were not able to fully confirm the exact supersession relationship between 4248223 and WE1X21975, so if your dryer's parts diagram shows 4248223, contact our support team with your model number and we'll verify fit before you order. Compatibility This thermal fuse is compatible with a wide range of GE dryer models, including: GTD42EASJ0WW, GTD42EASJ1WW, GTD42EASJ2WW, GTD42EASJ3WW GTD45EASJ0WS, GTD45EASJ1WS Many additional GTD-, DBXR-, and similar GE dryer model series Note: GE used this same thermal fuse across dozens of dryer model and sub-model variants over several production years. The list above is only a sample. Check your dryer's model/serial tag (typically on the door frame or cabinet edge) and compare against your unit's parts diagram, or contact our support team with your exact model number to confirm fit before ordering. Key Features Direct replacement thermal fuse for GE dryers 30 Amp, 250 Volt rating matches OEM specification Ceramic body 3AB-style fuse construction for heat resistance and reliability Cuts power to the heating circuit if the dryer overheats, protecting internal components Resolves no-heat, mid-cycle shutoff, and click-and-won't-start symptoms Simple, low-cost fix — typically a 15–20 minute repair with basic hand tools Product Specifications Part Number XPWE1X21975 OEM Part Number WE1X21975 Part Type Dryer Thermal Fuse (Safety Cutoff) Condition Aftermarket Replacement Amperage Rating 30 Amp Voltage Rating 250 Volt Fuse Type 3AB Ceramic Thermal Fuse (Non-Resettable) Application GE Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. On most GE dryers, this fuse is mounted on or near the heater housing/blower duct at the rear of the dryer, which typically requires removing the rear panel or top panel to access. It can be easy to overlook on the parts diagram, so compare the physical part against your model's diagram carefully before ordering or installing. Disconnect the wire terminals from the old fuse, note their positions, and transfer them to the same terminals on the new fuse. Before closing the dryer back up, inspect and clean the lint trap, exhaust duct, and vent hood for blockages, and check that the cycling thermostat is functioning — a fuse that blew due to an uncleared overheating cause will often blow again shortly after replacement. Frequently Asked Questions My dryer runs but doesn't heat — is this the part I need? A blown thermal fuse is one of the most common causes of a GE dryer that tumbles normally but produces no heat. It's worth testing the fuse for continuity with a multimeter before replacing it, since a few other components (the cycling thermostat, igniter on gas models, or heating element) can cause similar symptoms. Can this fuse be reset instead of replaced? No. This is a one-time thermal fuse, not a resettable thermostat or breaker. Once it blows, it's permanently open and must be replaced — there's no reset button or procedure. Why did my thermal fuse blow in the first place? This fuse blows in response to excessive heat, usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or by a failed cycling thermostat that no longer regulates temperature correctly. Clear the airflow path and check the thermostat when you replace the fuse, or the new one is likely to blow again. Where is this fuse located on my dryer? On most GE dryers it's mounted on or near the heater box/blower housing at the rear of the unit. Some installers find it tucked in a spot that isn't obvious even with the parts diagram in hand, so take your time locating it and confirm it visually matches before removing the old one. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less