Search results for "agitator"

XPARTCO WH12X955 Washer Lid Switch The XPARTCO WH12X955 is an aftermarket replacement lid switch assembly compatible with GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo units (including GE spacemaker and stacked laundry models). The lid switch is a safety component mounted inside the washer lid — it detects whether the lid is open or closed and signals the control that it's safe for the machine to start, agitate, and spin. When the lid closes, the switch activates and the washer can run through its full cycle. If the lid switch fails, the washer typically won't spin or drain, may not start or agitate at all, and clothes are left sitting in water. This is a complete lid switch assembly with an integrated wiring harness and ground wire. Dimensions: 1-1/4" H x 2-1/4" W x 16" D (the 16" depth is the wire harness that routes from the lid down into the washer cabinet). It directly replaces WH12X955, WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, and OEM6137363. Installation involves accessing the lid itself — the switch mounts inside the lid with two screws plus a separate ground wire screw. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH12X955 Washer Lid Switch fixes GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo units where the washer won't spin, won't drain, won't start, or won't agitate — leaving clothes sitting in water. Complete lid switch assembly with wiring harness and ground wire. Dimensions 1-1/4"H x 2-1/4"W x 16"D. Replaces WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, OEM6137363. Classic symptom: washer won't spin or drain. Common Problems This Part Fixes Washer won't spin — the classic lid switch failure symptom Washer won't drain — clothes left sitting in water at the end of the cycle Washer won't start at all — control not detecting a closed lid Washer won't agitate — the machine won't advance past the fill phase Machine doesn't recognize the lid is closed even when it is Lid switch body cracked from the lid being closed hard over time Internal switch contacts worn out — no longer signaling that the lid is closed Intermittent operation — washer sometimes spins, sometimes doesn't, depending on lid position Broken or frayed lid switch wiring harness Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WH12X955, 278666, AGE25981, AH270219, EA270219, PD00030733, EAP270219, PS270219, AP2045786, WH12X0955, EXPWH12X955 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select washer/dryer combo units (spacemaker and stacked laundry models) from the following brands: GE washer/dryer combo units — spacemaker and stacked laundry center models GE Spacemaker washers — select models Hotpoint washer/dryer combo units (select GE-built models) RCA washer/dryer combo units (select GE-built models) Kenmore / Sears washer/dryer combo units (select GE-built models) Note: This lid switch is specific to GE washer/dryer combo and spacemaker units — it is NOT the same switch used on standalone GE top-load washers, which use different lid switch part numbers. Always search by your appliance model number to confirm this part fits before ordering. Contact our support team with your model number if you're unsure. Key Features Lid switch safety assembly — detects whether the lid is open or closed and allows the washer to start, agitate, spin, and drain when the lid is shut Resolves the classic "won't spin" and "won't drain" symptoms of lid switch failure Complete assembly with integrated wiring harness and ground wire Dimensions: 1-1/4" H x 2-1/4" W x 16" D (the 16" depth is the wiring harness) Mounts inside the washer lid with two screws plus a separate ground wire screw Snap-in switch design with connector — no wiring modifications required Replaces WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, and OEM6137363 Compatible with GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo and spacemaker units Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH12X955 Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Application Washer/Dryer Combo & Spacemaker Units (GE platform) Dimensions 1-1/4" H x 2-1/4" W x 16" D Includes Lid switch, wiring harness, ground wire Function Prevents washer spin/agitation when lid is open Location Inside the washer lid Mounting Two screws + separate ground wire screw Compatible Brands GE, Hotpoint, RCA, Kenmore (GE-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves — The Lid Comes Off Disconnect power at the outlet or breaker before beginning. Wear work gloves to protect your hands from sharp sheet metal edges. This repair requires removing the washer lid to access the switch. Open the lid, then push it toward the back of the machine to release the plastic clips at the front that hold the lid up. Slowly lift the lid at the front — you'll see the lid switch is the only thing still connecting the lid to the washer body. Confirm the power is off, then unclip the electrical connector that joins the lid switch harness to the washer's wiring (it's typically a molex-style connector). With the connector released, you can carry the lid to a workbench or flat surface to work on it comfortably. On the underside/inside of the lid, remove the two screws on the right-hand side that hold the switch in place, then remove the screw that secures the ground wire to the inside of the lid. Lift out the old switch. The new WH12X955 switch snaps into place — seat it, reinstall the two mounting screws, and reattach the ground wire with its screw. Route the new harness cable through the same path as the old one; you can gently lift the retaining clips with a flathead screwdriver to slide the new cable through. Reconnect the electrical connector, set the lid back into position, and press it down until the front plastic clips engage. Restore power and test by closing the lid and running a cycle — confirm the washer agitates, drains, and spins. Tools needed: Phillips screwdriver, nut driver, flathead screwdriver, work gloves. (Tip: if you drop the ground wire nut inside the cabinet, a magnet on a stick makes retrieval easy.) Frequently Asked Questions My washer won't spin or drain — is the lid switch the cause? Yes — this is the single most common and telling symptom of a failed lid switch. The lid switch is a safety interlock that prevents the drum from spinning while the lid is open. When the switch fails (cracked body, worn internal contacts, or broken wiring), the control never receives the "lid closed" signal, so it blocks the spin and drain phases as a safety measure — leaving your clothes sitting in water. On many GE washer/dryer combos, a failed lid switch will also prevent the machine from starting or agitating at all. If your washer fills but goes no further, or completes the wash but leaves clothes soaked, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is depressed. Why is this switch 16" long? The 16" dimension is the length of the wiring harness, not the switch body itself. The switch mounts inside the washer lid, and its harness has to route from the lid, through the hinge area, down into the washer cabinet to reach the main wiring connector. That's why the assembly comes with a long attached cable — and it's also why this repair involves removing the lid to access everything. The switch body itself is compact at roughly 1-1/4" H x 2-1/4" W. Does this fit my standalone GE top-load washer? Probably not. The WH12X955 is specifically used on GE washer/dryer combo units and spacemaker/stacked laundry models. Standalone GE top-load washers use different lid switch part numbers. Because the lid switch design and mounting vary significantly across GE's washer lineup, always search by your appliance model number to confirm the correct part before ordering. If your unit is a standalone top-loader, contact our support team with your model number and we'll identify the right lid switch for it. Do I really have to take the lid off to install this? On most compatible models, yes — the lid switch mounts inside the lid itself, so you'll need to release the lid from the washer body to reach the two mounting screws and the ground wire screw. The good news is that the lid comes off fairly easily: push it toward the back to release the front plastic clips, then lift it slowly, unclip the electrical connector, and carry the lid to a comfortable work surface. Working on the lid off the machine is far easier than trying to reach into a cramped laundry closet. Just be sure power is disconnected before unclipping the connector. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions (1-1/4"H x 2-1/4"W x 16"D), harness and ground wire configuration, connector, mounting, and lid-detection function of the original WH12X955 lid switch used in compatible GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo and spacemaker units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WH01X27538 Washer Drive Belt The Genuine OEM GE WH01X27538 is a washer drive belt for GE and Hotpoint top-load washers. It is a 5-rib belt with 4 grooves, approximately 22.87 inches long. The belt connects the drive motor to the transmission pulley, so the motor can spin the basket and agitate the clothes. A worn, stretched, or broken belt can cause a washer that won't spin or agitate, a slow spin, squealing, or noise during the cycle. This is the original GE part. Belts differ between washer families, so check the part number against your model before ordering. Quick Answer The Genuine OEM WH01X27538 Drive Belt fixes a GE or Hotpoint top-load washer that won't spin or agitate, spins slowly, or squeals or makes noise because the drive belt is worn or broken. Classic symptom: the motor runs, but the basket or agitator doesn't turn. Common Problems This Part Fixes Motor runs but the basket or agitator doesn't turn Washer won't spin or agitate Slow spin or poor wash performance Squealing or noise during the cycle Visibly worn, cracked, stretched, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drive belt directly replaces the following part number: WH01X27538, replaces 290D1101P005, 4587903, 5PJ 586 SJ 161, AGE25699, AP6328256, OEM18984777, PD00043350, PS12299369 Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drive belt is listed for GE and Hotpoint top-load washers, including these examples: GE GTW220ACK4WW, GTW220ACK5WW, GTW330ASK4WW, GTW335ASN1WW GE GTW460ASJ8WW, GTW460ASJ9WW, GTW460ASJAWW Hotpoint HTW200ASK3WW, HTW240ASK5WS, HTW240ASK6WS Note: The models above are a small sample, not a full list. Washer belts differ between families, so compare your old belt to this one (approximately 22.87 inches, 5 ribs) and check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM GE drive belt for GE and Hotpoint top-load washers 5-rib, 4-groove design, approximately 22.87 inches long Connects the drive motor to the transmission pulley Resolves no-spin, no-agitate, and noise problems caused by a worn belt Typically a 30 minute to 1 hour repair Product Specifications Part Number WH01X27538 OEM Part Number WH01X27538 Part Type Washer Drive Belt Condition Genuine OEM Belt Length Approx. 22.87 Inches Belt Profile 5-Rib, 4-Groove Application GE & Hotpoint Top-Load Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Access to the belt depends on your model, so follow its service guide to reach the motor and pulleys. Note how the old belt is routed, remove it, and fit the new belt on the same pulleys. Check that it is seated in the pulley grooves before reassembling. Frequently Asked Questions My washer motor runs but the basket won't turn. Is this the part I need? A broken or slipping drive belt is a common cause. If the belt looks worn, cracked, or loose, replacing it is a good first step. How long is this belt? It is approximately 22.87 inches long, with 5 ribs and 4 grooves. If your old belt is a very different length or has a different number of ribs, check your model number before ordering. Is this a top-load or front-load part? It is listed for GE and Hotpoint top-load washers. If you are unsure which belt your washer uses, check your model number or contact our support team. Is this an easy repair? Retailers list it at roughly 30 minutes to 1 hour, though it depends on your model. Follow your model's service guide to reach the motor and pulleys. Will this fit my washer? It is listed for many GE and Hotpoint washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH02X10363 Genuine OEM GE Washer Hub Nut The WH02X10363 is a genuine GE OEM hub nut for GE, Hotpoint, and select RCA and Kenmore top-load washers. This nut is what secures the wash basket to the transmission's drive spline, holding the entire tub assembly firmly attached to the drive system. Every time the washer agitates or spins, this single nut is what keeps the basket properly seated and aligned rather than shifting or working loose under that repeated mechanical load. Over years of use, or from overloading the washer with oversized loads, this nut can loosen or wear enough that the basket no longer sits securely. A failed or loose hub nut typically shows up as a basket that wobbles or feels loose, unusual noise during agitation or spin, or in more advanced cases, a basket that isn't properly engaging with the drive system at all. It directly replaces AP5793681, 3029784, and PS8757009. Quick Answer The WH02X10363 Genuine OEM GE Washer Hub Nut fixes GE, Hotpoint, RCA, and Kenmore top-load washers with a wobbling or loose-feeling basket, unusual noise during agitation or spin, or a basket that isn't securely engaging with the drive system. Replaces AP5793681, 3029784, PS8757009. This nut requires a very specific torque — GE's own guidance calls for a 90 ft-lb torque-limiting extension and a 1-5/16" (33mm) impact socket. Using a standard impact wrench without the torque limiter can damage both the new nut and the transmission. Common Problems This Part Fixes Wash basket that wobbles or feels loose Unusual noise during agitation or spin Basket that isn't properly engaging with the drive system Missing or broken hub nut Basket instability that worsens with larger or unbalanced loads Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hub nut directly replaces the following OEM and cross-reference part numbers: WH02X10363, 3029784, AGE1396433, AP5793681, EAP8757009, PD00046649, PS8757009. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hub nut is compatible with select GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, Café, and Kenmore washers built on the GE platform, including model numbers such as GHWN8350D0WS and GTW465ASN2WW. Note: Always verify your full model number before ordering, since GE uses different hub nut sizes and thread designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified thread and torque rating Secures the wash basket to the transmission drive spline Resolves "wobbling basket," "loose feel," and "unusual noise during agitation or spin" symptoms 1-5/16" (33mm) nut size Direct drop-in replacement — matches the original thread and fit Replaces AP5793681, 3029784, and PS8757009 Compatible with GE, Hotpoint, RCA, Haier, Monogram, Café, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH02X10363 Part Type Washer Hub Nut Condition Genuine OEM Brand GE Application Top-Load Washers Size 1-5/16" (33mm) Function Secures the wash basket to the transmission drive spline Required Torque 90 ft-lb (torque-limiting extension required) Thread Direction Reverse-threaded — tightens counter-clockwise Repair Difficulty Moderate to Hard — specialized tools required Quantity 1 hub nut Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Critical — Correct Torque Tool Required, And This Nut Threads Counter-Clockwise Unplug the washer before beginning. Wear work gloves and safety glasses. Remove the fabric softener dispenser to access the agitator/auger assembly. Use a screwdriver to puncture through the inner shaft of the auger, then twist clockwise until the auger releases — this step can be difficult, and you'll need to hold the basket steady to keep it from rotating while you work. Lift the auger out. Remove the 11mm bolt underneath, then lift out the base assembly to expose the hub nut. Per GE's own guidance, removing and installing this nut requires a 90 ft-lb torque-limiting extension (GE part WX05X10028) along with a 1-5/16" (33mm) impact socket (GE part WX05X10022). Using a standard impact wrench without the torque limiter risks over-torquing, which can damage both the new nut and the washer's transmission. Unthread the old 33mm hub nut — this can also be difficult, so be patient and keep the basket from rotating. To install the new WH02X10363, thread it on going counter-clockwise, since this nut is reverse-threaded — the opposite direction of a standard nut. Align the base with the spline shaft, set it into position, and reassemble in reverse order: reinstall the 11mm bolt, reinstall the auger, and reattach the fabric softener dispenser. Restore power and run a test cycle to confirm the basket is stable with no wobble or unusual noise. Tools needed: impact driver or wrench with 90 ft-lb torque-limiting extension, 1-5/16" (33mm) deep well or impact socket, 3/8" to 1/2" adapter, 11mm socket, Phillips screwdriver, work gloves, safety glasses. Frequently Asked Questions Do I really need a special torque tool, or can I use a regular impact wrench? GE's own manufacturer guidance is explicit on this point: a 90 ft-lb torque-limiting extension must be used when removing or installing this hub nut to prevent damage to the nut and the transmission from over-torquing. A standard impact wrench alone can apply far more force than this nut and the transmission are designed to handle, so skipping the torque limiter risks turning a simple nut replacement into a much larger and more expensive transmission repair. Which direction does this nut turn to tighten? This nut is reverse-threaded, meaning it tightens by turning counter-clockwise — the opposite of a standard nut. This is an easy detail to miss if you're not expecting it, and turning it the wrong direction won't seat it correctly. Keep this in mind both when removing the old nut and installing the new one. My basket feels wobbly. Is this definitely the hub nut? It's a strong possibility, especially if the wobble has developed gradually or worsened after washing unusually large or unbalanced loads. Since this nut is what holds the entire basket assembly firmly attached to the transmission's drive spline, a loosened or worn nut directly translates into a basket that no longer sits securely. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original thread design, size, and torque rating of the hub nut originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10404050 Genuine OEM Washer Lid Switch Assembly The W10404050 is a Genuine OEM replacement lid switch and latch assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge top-load washers. The lid switch is a critical safety component that detects when the washer lid is opened or closed. It sends a signal to the control board to allow the washer to fill, agitate, and spin when the lid is closed — and to immediately stop the spin cycle when the lid is opened, preventing contact with a moving drum. This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It features a 4-wire plug connection and includes two bezels (one white and one gray) to match different model color schemes. It directly replaces W10238287, W10744659, W10404050VP, AP5263307, and several additional cross-reference numbers. The companion lid strike (W10240513) is sold separately — inspect the strike on your lid for wear or damage and replace if needed. Installs in 20–30 minutes with basic hand tools. Quick Answer The W10404050 Genuine OEM Washer Lid Switch Assembly fixes top-load washers that won't start, won't spin, have a blinking lid lock light, or continue spinning with the lid open. 4-wire plug connection. Includes white and gray bezels. Replaces W10238287, W10744659, AP5263307, and more. Compatible with Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge washers. Lid strike W10240513 sold separately. Common Problems This Part Fixes Washer will not start — lid lock light blinks without locking Washer fills but will not agitate or spin Washer lid lock light continuously blinks and clicks without engaging Washer continues to spin with the lid open — safety mechanism not working Lid appears locked but washer will not proceed past sensing or fill cycle Washer stops mid-cycle and will not restart without opening and re-closing the lid Lid lock assembly visibly broken or latch no longer springs back after pressing Replaces Part Numbers This lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10404050, 1938607, W10238287, W10404050VP, W10744659, EAP3497627, AWP41256, PD00003596, AH3497627, AP5263307, EA3497627, PS3497627. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid switch assembly is compatible with select top-load washers from the following brands: Whirlpool top-load washers — Cabrio and WTW series (electronic top-load models) Maytag top-load washers — Centennial, Bravos X, and MVWC/MVWX series Kenmore / Sears top-load washers — 110 series and select others (Whirlpool-built) Amana top-load washers — NTW and ATW series KitchenAid top-load washers Roper top-load washers Admiral top-load washers — ATW series Crosley top-load washers Inglis top-load washers Magic Chef top-load washers Norge top-load washers Note: The W10404050 is for electronic top-load washers with a 4-wire lid lock (Cabrio, Centennial, Bravos, and similar platforms). Older mechanical top-load washers use a different lid switch style. Verify your model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Critical safety component — stops the spin cycle when the lid is opened to prevent contact with a moving drum Signals the control board to allow filling, agitating, and spinning when the lid is properly closed and locked 4-wire plug connection — direct plug-in replacement on compatible models Includes two bezels (white and gray) to match different model color schemes Replaces W10238287, W10744659, W10404050VP, AP5263307, and more Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos X, Kenmore 110 series, and many more Lid strike W10240513 sold separately — inspect and replace if worn Product Specifications Part Number W10404050 Part Type Washer Lid Switch and Latch Assembly Condition Genuine OEM Application Electronic Top-Load Washers (4-wire lid lock) Connector 4-wire plug Color White (includes both white and gray bezels) Includes Lid switch assembly, white bezel, gray bezel Companion Part W10240513 Lid Strike (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, Norge Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. The lid switch assembly is mounted under the washer's top panel near the lid opening. To access it, insert a putty knife about 2 inches from each front corner of the top panel to release the spring clips and lift the top panel. Disconnect the 4-wire harness from the old lid switch assembly. Remove the mounting screws securing the assembly and lift it out. Install the new W10404050 assembly, secure with the mounting screws, and reconnect the 4-wire harness. Choose the appropriate bezel (white or gray) for your model and snap it into place. Lower the top panel until the clips engage. Restore power and run a test cycle to confirm the lid locks, the washer starts, and the spin cycle stops when the lid is opened. Tip: While the top panel is raised, inspect the lid strike (W10240513) on the lid for cracks or wear — if worn, replace it at the same time. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What does the washer lid switch do? The lid switch assembly serves two functions. First, it is a safety device — when the lid is opened during the spin cycle, the switch immediately cuts power to the spin motor to prevent contact with the moving drum. Second, it signals the control board that the lid is securely closed and locked, allowing the washer to proceed through the fill, agitate, and spin cycles. If the switch fails, the washer either won't start at all, or will fail to proceed past a specific cycle stage because the board cannot confirm the lid is closed. My lid lock light is blinking — does that mean the lid switch needs to be replaced? A blinking lid lock light is one of the most common symptoms of a failed W10404050 lid switch assembly. It typically means the lid lock mechanism is attempting to engage but failing — either because the switch is internally faulty or because the lid strike (W10240513) on the lid is broken and not triggering the switch properly. Inspect the lid strike first — if it is cracked or missing, replace it. If the strike looks intact and the lid lock still blinks without engaging, replace the W10404050 switch assembly. Should I also replace the lid strike (W10240513) at the same time? It depends on the condition of the strike. Open the lid and inspect the two plastic prongs on the underside of the lid that engage the W10404050 latch — this is the W10240513 lid strike. If the prongs are cracked, broken, or noticeably worn down, replace the strike at the same time as the switch assembly. Since the top panel is already lifted for the switch replacement, it is a good opportunity to inspect and replace the strike if needed, using only a Phillips screwdriver. What washers is the W10404050 compatible with? The W10404050 is used on Whirlpool Cabrio and WTW series electronic top-load washers, Maytag Centennial and Bravos X top-load washers, and Kenmore 110 series top-load washers, among others. It is specifically for electronic top-load models with a 4-wire lid lock — not for older mechanical top-load washers that use a simpler 2- or 3-wire lid switch. Verify your model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid switch and latch assembly installed in compatible washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP21352320 Genuine OEM Whirlpool Washer Drive Belt The WP21352320 is a genuine Whirlpool OEM drive belt for Whirlpool top-load washers. This belt connects the drive motor to the transmission at the bottom of the washer, and it's what actually spins the basket during the wash and spin cycles. Unlike a dryer's drum belt, which simply tumbles a drum, this washer drive belt has to transfer real torque to spin a heavy, water-filled basket, which puts it under considerably more mechanical stress. Measuring approximately 51" long and 3/8" wide. A worn or broken belt produces a distinctive set of symptoms: the washer may not spin at all, spin only slowly, agitate poorly or not at all, fail to drain properly since the pump relies on the same drive system, or produce a burning smell or loud grinding noise as a worn belt slips against the pulley. One useful diagnostic tip worth knowing: a belt can look intact at a glance but still be worn out — if the sides of the belt appear shiny or glazed rather than matte, that's a sign of slippage-related wear even without a visible crack. It directly replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882. Quick Answer The WP21352320 Genuine OEM Whirlpool Washer Drive Belt fixes Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers with a drum that won't spin, spins slowly, won't agitate, won't drain, or produces a burning smell or loud grinding noise. Approximately 51" long, 3/8" wide. Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, PS11738882. A belt can look intact but still be worn out — check the sides for a shiny, glazed appearance, which indicates slippage wear even without a visible crack. Common Problems This Part Fixes Washer drum won't spin, or spins only slowly Washer won't agitate during the wash cycle Washer won't drain properly Burning smell coming from the washer during operation Loud grinding noise from underneath the washer Washer that shakes or moves excessively during spin Washer that won't start or stalls partway through a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP21352320, 21352320, 21001478, 35-2073, 35-2320, 35-3662, PD00002418, EAP11738882, AP6005822, AWP46532, PS11738882, WP21352320VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Whirlpool top-load washers, and also fits select Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, and Ikea washers built on the Whirlpool platform, including model numbers such as HAV3460AWW. Note: Always verify your full model number before ordering, since Whirlpool uses several different drive belts across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, width, and material Connects the drive motor to the transmission to spin the basket Resolves "won't spin," "won't agitate," "won't drain," "burning smell," and "grinding noise" symptoms caused by belt failure Approximately 51" long, 3/8" wide Direct drop-in replacement matching the original belt routing Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882 Compatible with Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP21352320 Part Type Washer Drive Belt Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Length Approx. 51 in. Width 3/8 in. Attaches To Motor pulley and transmission Repair Difficulty Medium — basic hand tools required Quantity 1 drive belt Compatible Brands Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, Ikea Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Consider The Motor Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker, and shut off both the hot and cold water supply valves before beginning. Pull the washer out from the wall for full access. Wear work gloves. Locate the drive belt around the motor at the bottom of the washer. Use a flathead screwdriver or hex wrench to remove the screws holding the motor bracket in place, which releases tension on the belt. Carefully slide the motor bracket off the motor, and use pliers if needed to work the old belt off the pulley. While the bottom of the washer is accessible, this is a good time to inspect the motor pulley for wear as well, since it's a related component you'll already have exposed. Install the new WP21352320 belt around the pulley and transmission, following the same routing as the old belt, and make sure it's seated securely and tightened properly — a loose or improperly seated belt will slip and wear out quickly. Reattach the motor bracket with its screws. Restore the water supply and power, then run a test cycle to confirm the washer spins, agitates, and drains normally with no unusual noise. Tools needed: multi-bit screwdriver, hex wrench, standard pliers, work gloves. Frequently Asked Questions My belt looks fine — no cracks or visible damage. Could it still need replacing? Yes, and this is a common source of confusion. A belt can appear intact with no cracks and still be worn out. Check the sides of the belt closely: if they look shiny or glazed rather than having a matte, textured surface, that glazing indicates the belt has been slipping against the pulley, which is a clear sign of wear even without visible cracking. My washer pumps and drains but the drum spins slowly or not at all. Is this the belt? Yes, this is one of the most direct symptoms of a worn or slipping drive belt. Since this belt is what actually transfers the motor's power to spin the basket, a worn belt can slip under load, causing slow or absent spinning even though the motor itself and the drain pump are both working normally. Should I replace the motor pulley at the same time? It's worth inspecting while you have the bottom of the washer accessible, even if you don't end up replacing it. A worn pulley can accelerate wear on a brand-new belt, so checking its condition during this repair is a reasonable precaution, especially if your old belt showed the glazed, slipping-related wear pattern. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and routing configuration of the drive belt originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3355806 Washer Lid Switch Replaces WP3355806 The XPARTCO 3355806 is an aftermarket replacement stackable washer lid switch assembly compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, and Magic Chef stacked washer/dryer laundry centers (thin twin and space-saver units). The lid switch is a safety component mounted near the top of the washer — it detects whether the lid is open or closed and prevents the washer from spinning while the lid is open. When you close the lid, a pin on the lid activates the lever on the switch, signaling the control that it's safe to spin. Without a functioning lid switch, the washer won't spin as a safety measure, even though it may still fill and agitate normally. The switch commonly fails in one of two ways: the plastic body cracks from the lid being slammed over time, or the internal switch contacts wear out and can no longer signal that the lid is closed. Features an 11" wiring harness with round plugs and a 7/8" block connector. It directly replaces WP3355806, WP3355806VP, 3355806, 520880, AP6008072, AP2947199, AH11741201, EA11741201, EAP11741201, PS11741201, PS341529, and PD00002599. Installs in 15–30 minutes with basic hand tools and novice repair experience. Quick Answer The XPARTCO 3355806 Washer Lid Switch fixes Whirlpool, Kenmore, Roper, Estate, and KitchenAid stacked washer/dryer laundry centers where the washer won't spin but still agitates and fills, the machine doesn't detect the lid is closed, or the washer won't start. Stackable washer lid switch assembly — 11" harness with round plugs, 7/8" block. Replaces WP3355806, WP3355806VP, 520880, AP6008072, AP2947199, AH11741201, EA11741201, EAP11741201, PS11741201, PS341529. Compatible with Whirlpool LTE5243/LTG5243 series, Roper RTE5243/RTG5243, and Kenmore thin twin models. Classic symptom: won't spin but still agitates. Common Problems This Part Fixes Washer won't spin but still agitates and fills — the classic lid switch failure symptom Washer won't start at all — control not detecting a closed lid Machine doesn't recognize the lid is closed even when it is Lid switch body cracked from the lid being slammed over time Internal switch contacts worn out — no longer signaling lid closed Washer stops mid-cycle when it should transition to spin Clothes coming out sopping wet because the spin cycle never runs Intermittent operation — washer sometimes spins, sometimes doesn't, depending on lid position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WP3355806, ER3355806, 3355806, AP6008072, AWP47529, EAP11741201, PD00002599, PS11741201. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select stacked washer/dryer laundry centers (thin twin / space-saver units) from the following brands: Whirlpool laundry centers — LTE5243DQ0-DQ8, LTE5243DT2-DT7, LTE5243DZ0/DZ1/DZ2, LTE5243BN0/BN1, LTG5243DQ0-DQC, LTG5243DT3/DT4/DT7/DT8, LTG5243DZ1/DZ2, LTG5243BN0/BN1 series and related Whirlpool laundry centers — WET4024EW and related stacked models Roper laundry centers — RTE5243BL0, RTE5243BW0, RTG5243BL0, RTG5243BW0 series Kenmore / Sears laundry centers — thin twin models (110.9975820, 110088732791-11088754793, 11098573100-11098573800 series and related) Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, Magic Chef — select stacked washer/dryer models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Stackable washer lid switch assembly — detects whether the lid is open or closed and prevents spinning when the lid is open Resolves the classic "won't spin but still agitates" symptom of lid switch failure Restores the safety interlock and allows the washer to complete its spin cycle Features an 11" wiring harness with round plugs and a 7/8" block connector Designed for thin twin, space-saver, and other stacked washer/dryer laundry centers Replaces WP3355806, WP3355806VP, 520880, AP6008072, AP2947199, AH11741201, EA11741201, EAP11741201, PS11741201, PS341529, and PD00002599 Compatible with Whirlpool LTE5243/LTG5243 series, Roper RTE5243/RTG5243 series, and Kenmore thin twin laundry centers, plus Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, and Magic Chef stacked units Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3355806 OEM Part Number WP3355806 Part Type Stackable Washer Lid Switch Assembly Condition Aftermarket Replacement Application Stacked Washer/Dryer Laundry Centers (Whirlpool platform) Harness Length 11" with round plugs Block Connector 7/8" Function Prevents washer spin when lid is open Location Near top of washer, behind front panel Compatible Brands Whirlpool, Kenmore, Roper, Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Unplug the appliance (or shut off the house circuit breaker) and turn off the hot and cold water supplies before beginning. Wear work gloves to protect your hands. On these stacked laundry centers, the lid switch is accessed by removing the front panel or the top panel — unscrew the screws along the edge of the panel and set it aside. Note: on some Whirlpool space-saver units, the hardest part of the job is getting the washer lid off to access the switch, so take your time and consult a model-specific diagram or video. Once the panel is off, locate the lid switch assembly near the top of the machine. Photograph the wiring harness connections before disconnecting anything. Unscrew the retaining screws that hold the lid switch in place, then carefully disconnect the wiring harness from the switch. Connect the wiring harness to the terminals on the new 3355806 switch, following the diagram on the switch for proper installation. Secure the new switch in place with the retaining screws. Reinstall the panel and secure it with the screws. Turn the water supplies back on, plug the washer back in, and test by closing the lid and running a cycle — the machine should advance to spin when the lid is shut. Tools needed: Multi-screwdriver, socket wrench (some models), work gloves. Frequently Asked Questions My washer agitates and fills but won't spin — is the lid switch the cause? Yes — this is the single most common and telling symptom of a failed lid switch. The lid switch is a safety interlock that prevents the drum from spinning while the lid is open. When the switch fails (cracked body or worn internal contacts), the control never receives the "lid closed" signal, so it blocks the spin cycle as a safety measure — but agitation and fill still work because those don't require the lid interlock. If your washer runs through wash and agitate normally but stops when it should spin, leaving clothes sopping wet, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is pressed. What causes the lid switch to fail? There are two common failure modes. First, the plastic body of the switch can crack over time from the lid being closed hard or slammed repeatedly — the repeated impact stresses the housing until it fractures. Second, the internal electrical contacts wear out from thousands of open/close cycles and can no longer make a reliable connection to signal that the lid is closed. Either way, the fix is the same: replace the lid switch assembly. To extend the life of the new switch, close the lid gently rather than letting it slam. What's the difference between 3355806 and WP3355806? These are the same lid switch across production revisions. 3355806 was the original part number and WP3355806 is the Whirlpool-era part number (with the "WP" prefix Whirlpool adopted) for the same switch. WP3355806VP is a variant packaging code. All are physically and functionally identical — if your laundry center's parts diagram shows any of these numbers, this listing is the correct replacement. The cross-references 520880, AP6008072, and PS11741201 are additional catalog identifiers for the same part. Does this fit my thin twin or space-saver laundry center? This lid switch is specifically designed for stacked washer/dryer laundry centers — the "thin twin," space-saver, and similar stacked units from Whirlpool and its related brands. It fits the Whirlpool LTE5243/LTG5243 series, Roper RTE5243/RTG5243 series, and a wide range of Kenmore thin twin models, among others. Check your model number against the compatibility list above. If your unit is a standalone (non-stacked) top-load washer, it likely uses a different lid switch — contact our support team with your model number and we'll confirm the correct part. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the fit, 11" harness with round plugs, 7/8" block connector, terminal configuration, and lid-detection function of the original WP3355806 lid switch used in compatible Whirlpool, Kenmore, Roper, Estate, and related stacked washer/dryer laundry centers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8572717 Washer Motor Start Capacitor The XPARTCO 8572717 is an aftermarket replacement motor start capacitor for Whirlpool-built top-load washers and washer/dryer combination units. Unlike a run capacitor that stays in the circuit continuously, this start capacitor's job is brief and intense: at the instant the motor is commanded to start, it delivers a strong momentary boost of voltage to help the motor overcome its own inertia and get up to speed quickly. Once the motor reaches running speed, a relay switches it out of the circuit, handing off to the run capacitor for continuous operation. That short, high-stress duty cycle is exactly why start capacitors are a common failure point — they work hard for a fraction of a second on every single cycle start. Rated 189–227 MFD at 125VAC, 60Hz. The capacitor is a black cylindrical component mounted to the rear panel of the washer, held in place by a small plastic retaining clip and wrapped in a foam shield that protects it from moisture. Common failure modes include the internal dielectric breaking down from repeated startup stress, and in some cases the capacitor overheating badly enough to produce visible smoke if it fails while still energized. A failing start capacitor produces a clear symptom: the washer motor hums but won't start, or the motor fails to spin up while other functions of the washer still respond normally. It directly replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006. Quick Answer The XPARTCO 8572717 Washer Motor Start Capacitor fixes Whirlpool-built top-load washers and washer/dryer combos where the motor hums but won't start, the washer won't agitate or spin, or there's a burning smell from the motor area. Includes foam shield. 189–227 MFD, 125VAC, 60Hz. Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Washer motor hums but won't start Washer won't agitate Washer won't spin or drain because the motor never starts Burning smell coming from the motor area Washer that starts a cycle but the drum never begins moving Motor that struggles to start under load but may start when the drum is empty Visible discoloration, bulging, or a burnt smell from the capacitor itself Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer motor start capacitor directly replaces the following OEM and cross-reference part numbers: 8572717, WP8572717, 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor start capacitor is compatible with select Whirlpool-built top-load washers and washer/dryer combination units across the Whirlpool family of brands, including: Whirlpool top-load washers and washer/dryer combos — WET, WGT series Kenmore top-load washers (select Whirlpool-built 110-series models) Maytag, KitchenAid, Jenn-Air, and Amana washers (select models) Roper, Admiral, Hardwick, and Estate washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric washers (select models) Select Ikea washers built on the Whirlpool platform Verified model numbers include: WET4027EW, WET4024EW, LTE5243DQ, WET3300XQ, WGT3300XQ, MTW5670TQ0, SAWS800JQ1, LSN7233BW1, LSR7233DZ1, LSQ8243HQ0, LSQ8512KQ0, LSQ8543JQ0, LSQ8543JQ1, LSQ8543JT0, LSQ8543JT1, LSQ9244EQ0, LSQ9544KQ0, LSQ9549LG0, LSQ9549LG1, LSQ9549LG2, LSQ9549LG3, LSQ9549PW2, 8LSC6244BQ0, and Kenmore 110.72407600, 110.72408440, 110.74414130, 110.81360430, 110.82074620, 110.82984100, 110.91565810, and 110.98573110. Note: This capacitor fits both standalone washers and Whirlpool washer/dryer combination units. Always verify your full model number before ordering, since specifications and mounting can vary by platform. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement start capacitor — delivers a momentary voltage boost to get the washer motor spinning at startup Resolves "motor hums but won't start," "won't agitate," "won't spin," and "burning smell" symptoms caused by capacitor failure Rated 189–227 MFD, 125VAC, 60Hz Includes foam shield to protect against moisture — transfer or reuse per your model's original configuration Direct drop-in replacement — mounts to the same rear panel retaining clip Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and related top-load washers and washer/dryer combos Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8572717 OEM Part Number WP8572717 Part Type Washer Motor Start Capacitor Condition Aftermarket Replacement Application Top-Load Washers / Washer-Dryer Combos (Whirlpool-Built) Capacitance 189–227 MFD (µF) Voltage 125VAC Frequency 60 Hz Shape Cylindrical (black) Included Components Foam moisture shield Mounting Rear panel, plastic retaining clip Quantity 1 start capacitor Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Ikea Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Unplug the washer or shut off the house circuit breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching either terminal, discharge the capacitor by shorting its two terminals together using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified appliance technician replace this part instead. ⚠️ Transfer The Foam Shield To The New Capacitor Wear work gloves. Remove the washer's console and then the spring clips that secure the top/body assembly to the washer frame, using a putty knife to gently release them. With the body lifted or set aside, locate the capacitor — a black cylindrical component mounted to the rear panel, held in place by a small plastic retaining clip. Using a flat-blade screwdriver, gently pop the plastic clip away from the capacitor to release it. After confirming the capacitor is fully discharged, unplug it from the appliance wiring. Remove the foam shield from the old capacitor and transfer it onto the new one before installing — this shield protects the capacitor from moisture, and skipping it leaves the new part more exposed to washer humidity. Connect the new 8572717 capacitor to the wiring, snap it back into the plastic retaining clip in the same position, and reassemble the body, spring clips, and console in reverse order. Restore power and run a test cycle to confirm the motor starts promptly on both agitate and spin. Tools needed: putty knife, flat-blade screwdriver, Phillips screwdriver, insulated-handle screwdriver or capacitor discharge tool, work gloves. Frequently Asked Questions My washer motor hums but won't start. Is this the right part? Yes, this is the classic symptom of a failed start capacitor. Since this capacitor's entire job is delivering the momentary voltage boost needed to get the motor spinning from a standstill, a failure here often leaves the motor energized and humming but unable to actually overcome its own inertia and start turning. What's the difference between a start capacitor and a run capacitor? A start capacitor works only for a brief moment — it delivers a strong voltage boost the instant the motor is told to start, then a relay switches it out of the circuit once the motor reaches running speed. A run capacitor, by contrast, stays in the circuit continuously while the motor operates, correcting current phase for efficiency. Because the start capacitor works so hard in such a short burst on every single start, it's a more common failure point than a run capacitor on this type of motor. Do I need to reuse the foam shield from my old capacitor? Yes, it's worth transferring. The foam shield wraps around the capacitor to protect it from moisture inside the washer cabinet, and reusing it on the new capacitor helps the replacement hold up the same way the original was designed to. If the foam has degraded significantly, you can skip it, but it's a simple step that adds meaningful protection. My old capacitor got hot and smoked. Is that dangerous? Yes — a capacitor that overheats to the point of smoking has failed in a way that can pose a fire or electrical hazard, and the washer should not be used again until it's replaced. This kind of failure typically happens when a capacitor stays energized longer than it should, generating heat it isn't designed to dissipate. Replace the capacitor and, if the washer's start relay or timer seems to be holding the capacitor in the circuit too long, have that checked as well. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (189–227 MFD, 125VAC, 60Hz), cylindrical form factor, and mounting configuration of the original WP8572717 start capacitor used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, and related top-load washers and washer/dryer combos. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3949238 Washer Lid Switch Replaces WP3949238 The XPARTCO 3949238 is an aftermarket replacement lid switch assembly for Whirlpool top-load washers, and also fits select Kenmore models. This switch confirms the lid is closed before the washer will spin — a pin on the underside of the lid pushes against the switch's lever, telling the machine it's safe to proceed with the cycle. Includes a 3-wire lead and a metal shield for added durability. Over time, the switch's internal contacts can wear out or fail electrically. If your washer will agitate but won't spin, this switch is a strong candidate for the cause. Symptoms of a failing lid switch include the washer not spinning, not draining, not starting, not agitating, the cycle failing to advance, or the lid not closing properly. It directly replaces WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021. Quick Answer The XPARTCO 3949238 Washer Lid Switch fixes Whirlpool and Kenmore top-load washers that won't spin, won't drain, won't start, won't agitate, won't advance through the cycle, or have a lid that won't close properly. Includes 3-wire lead, metal shield. Replaces WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021. If your washer agitates fine but won't spin, that's the classic symptom pointing to this switch. Common Problems This Part Fixes Washer not spinning Washer not draining Washer not starting Washer not agitating Cycle not advancing Lid or door won't close properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch is compatible with select Whirlpool top-load washers, and also fits select Kenmore washers built on the Whirlpool platform, including model numbers such as 11015732400, 11015842400, 11015852400, 11020692000, 11020602992, 11020612990, 11020612991, 11020622990, 11020622991, 11020632990, 11020632991, 11020642990, 11020642991, 11021894000, 11022292100, 11022294100, 11022422100, 11022432100, 11022442100, 11022622100, 11022632100, 11022642100, 11022652100, 11022662100, 11022692100, 11022692101, 11022702100, 11022702101, 11022712100, 11022722100, and 11022722101. Note — not the same as 3949247: A similarly-numbered switch, 3949247, is a separate part used on different models. Whirlpool also uses several other distinct lid switch designs, including the direct-drive style (8318084) and the thin-twin style (3355806), which are not interchangeable with this switch. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your washer needs. Key Features Aftermarket replacement lid switch assembly — confirms the lid is closed before allowing the washer to spin Resolves "won't spin," "won't drain," "won't start," "won't agitate," "cycle not advancing," and "lid won't close" symptoms 3-wire lead with metal shield for added durability Direct drop-in replacement matching the original mounting and connection Replaces WP3949238, 3949238, WP3949238VP, 10800-61, AP6008880, AWP47911, EAP11742021, OEM18026649, PD00002488, PS11742021 Compatible with Whirlpool and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Requires basic hand tools, some disassembly, novice repair experience Product Specifications Part Number 3949238 OEM Part Number WP3949238 Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Wiring 3-wire lead Shield Metal Function Confirms lid is closed before allowing the washer to spin Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 lid switch assembly Compatible Brands Whirlpool, Kenmore Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Unplug your washer and turn off the water supply before you begin — make sure both the hot and cold water supplies are shut off. Remove the screws located on the back of the washer cabinet, usually located at the top of the access panel. Lift or tilt the top of the washer to access the lid switch, typically mounted near the lid opening. Photograph the wiring before disconnecting anything. Disconnect the wire connectors from the old switch and remove the mounting screws securing it in place. Install the new 3949238 in the same position, reconnect the wire connectors fully, and secure the mounting screws. Reassemble the washer cabinet and secure its screws. Restore power and water, then run a test cycle with the lid closed to confirm the washer spins normally. Tools needed: multi screwdriver. Frequently Asked Questions My washer agitates but won't spin. Is this the part I need? Yes, this is the classic and most reliable symptom of a failed lid switch. This switch confirms to the washer's control system that the lid is closed before allowing the spin cycle to run — a failed switch commonly still allows agitation while preventing spin, since spin specifically requires the lid-closed signal. Is this the same as the 3949247 switch I've seen listed nearby? No, these are separate lid switch part numbers, despite the similar numbering. 3949247 is used on different models. Always confirm your exact part number from your washer's parts diagram or the sticker on your old switch before ordering. Is this a difficult repair? No, this is a straightforward repair requiring basic hand tools and some cabinet disassembly, suitable for a novice DIYer. A multi screwdriver is typically all that's needed. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the wiring, mounting, and switching function of the original WP3949238 lid switch assembly used in compatible Whirlpool and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool WP8577376 Washer Genuine OEM Transmission Shaft Seal Factory replacement transmission stem / agitator shaft seal for select Whirlpool-built top-load washers. Product Overview WP8577376 is a Genuine Whirlpool OEM washer shaft seal. Whirlpool describes it as a washing machine transmission stem seal, while Sears identifies it as an agitator shaft seal. The seal helps prevent wash water from leaking between the tub mounting stem and the agitator drive shaft, protecting the transmission/drive area from moisture. Quick Answer WP8577376 is the current Genuine Whirlpool OEM replacement for several older washer shaft and center-post seals. It is commonly used on older Whirlpool-built direct-drive top-load washers. Common Problems This Part May Fix Water leaking around the agitator or center-post area Moisture reaching the transmission or drive system Worn, cracked, hardened, or missing shaft seal Leak discovered during tub or transmission service Replaces and Cross-References WP8577376, WP91938, 8577376, 91938, 1181094, 356934, 356934BULK, 356934D, 99404, J27-500, J27-661, LP630, LP631, AP6013521, AWP49388, PD00005095, PS11746747 Cross-reference numbers are provided for identification. Always verify the complete appliance model number before ordering. Compatibility Fits select Whirlpool-built washers sold under Whirlpool, Kenmore, KitchenAid, Roper, Estate, Crosley, Admiral, Amana, Magic Chef, Maytag and related brands. Compatible model examples include: LSR7233DZ1 LSQ8243HQ0 LSQ8512KQ0 LSQ8543JQ0 LSQ9110PW3 LSQ9544KQ0 LSQ9549LG1 110.10502990 110.16602690 110.73875800 110.71770610 110.73775200 Important: This is only a partial compatibility list. Verify the full washer model number and original seal number before purchase. Key Features Genuine Whirlpool OEM replacement part Transmission stem / agitator drive shaft sealing function Helps prevent water intrusion into the drive area Updated replacement for multiple older shaft-seal numbers Designed for select Whirlpool-built top-load washers Product Specifications Manufacturer Part Number WP8577376 Brand Whirlpool Part Type Transmission Stem / Agitator Shaft Seal Condition New Part Quality Genuine OEM Application Washer Tub / Transmission Shaft Sealing Package Quantity 1 Shaft Seal Installation Notes Unplug the washer and shut off both water-supply valves before service. Drain any remaining water and follow the appliance service procedure for tub/drive-system access. Remove the old shaft seal without damaging the mounting surface or drive shaft. Clean the sealing surface before installing the replacement. Install the new seal in the correct orientation and reassemble the washer. Run a test cycle and inspect carefully for leaks. Service note: A leak in this area can also involve worn tub seals, a damaged mounting stem, corrosion, or transmission/shaft wear. Inspect related components while the washer is disassembled. Frequently Asked Questions Is WP8577376 a Genuine Whirlpool OEM part? Yes. WP8577376 is a Genuine Whirlpool OEM replacement shaft seal. What does this seal do? It helps prevent water from leaking between the tub mounting stem and agitator drive shaft. Does WP8577376 replace 8577376 and 91938? Yes. Those are among the earlier part numbers superseded by WP8577376. Is this the complete transmission? No. This listing is for the shaft seal only. The transmission/gearcase and other seals are not included. Shop With Confidence Use your washer's complete model number to confirm fitment before ordering. Genuine Whirlpool OEM Factory Replacement Compatibility Support Fast U.S. Shipping

Read more less

XPARTCO W10780048 Washer Suspension Rods Kit Washer Suspension Rods Kit, set of 4. Fits specific Kenmore, Maytag, Whirlpool top load machine models. Replaces Part numbers: W10780048, W10349191, 4185114, W10257087, W10257088, W10349193, W10748952, W10821948, AP5971398, PS11703290. Description: This Suspension Rods are replacement parts for specific Kenmore, Maytag, Whirlpool washing machine models. They are designed to support the washer's tub assembly, maintaining balance and stability during the spin and agitation cycles. These rods connect the tub to the washer's frame and help absorb vibrations, preventing excessive movement that can lead to operational issues.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XPARTCO 3949247 Washer Lid Switch Replaces 3949247V The XPARTCO 3949247 is an aftermarket replacement lid switch assembly for Whirlpool top-load washers, and also fits select Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid models, including stacked washer/dryer laundry center units. This switch mounts to the underside of the cabinet top panel and tells the washing machine the lid is closed, allowing the wash cycle to begin. Black plastic with wire leads, sold individually. Over time, the plastic on the switch's actuator can become brittle with age and break when the lid is closed roughly, or from the movement of an unbalanced load causing parts of the washer to strike it. Symptoms of a failing lid switch include the wash cycle not starting even when the lid is closed, error codes related to the lid being open, inability to advance through cycle selections, or the washer not spinning while still agitating normally. It directly replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098. Quick Answer The XPARTCO 3949247 Washer Lid Switch fixes Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid top-load washers (including laundry center combo units) that won't start with the lid closed, show lid-open error codes, won't advance through cycle selections, or agitate but won't spin. Black plastic, wire leads, sold individually. Replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098. Not the same as our 3949238 listing — these are separate, similarly-numbered switches used on different models. Common Problems This Part Fixes Wash cycle won't start even when the lid is closed Error codes related to the lid being open Inability to advance through cycle selections Washer agitates but won't spin Flashes or other improper lid switch behavior Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch is compatible with select Whirlpool top-load washers, and also fits select Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers built on the Whirlpool platform, including stacked washer/dryer laundry center units, and model numbers such as 11010202000, 11010202001, 11010502990, 11010502991, 11010852990, 11010852991, 11012202100, 11012502100, 11012852100, 11013202200, 11013212200, 11014102300, 11014112300, 11014202300, 11014212200, 11018202790, 11018522790, 11018522791, 11018532790, 11018542890, 11018542891, 11018609890, 11018702790, 11018702791, 11019101990, 11019101991, 11019101992, 11019202200, and 11020112000. Note — not the same as 3949238: Our 3949238 listing is a separate, similarly-numbered lid switch used on different models. Whirlpool also uses several other distinct lid switch designs, including the direct-drive style (8318084) and the thin-twin style (3355806), which are not interchangeable with this switch. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your washer needs. Key Features Aftermarket replacement lid switch assembly — confirms the lid is closed before allowing the wash cycle to begin Resolves "won't start," "lid-open error codes," "can't advance cycle selections," and "agitates but won't spin" symptoms Black plastic construction with wire leads Mounts to the underside of the cabinet top panel Direct drop-in replacement matching the original mounting and connection Replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098 Compatible with Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers, including laundry center units Aftermarket replacement built to OEM-equivalent quality standards Sold individually Product Specifications Part Number 3949247 OEM Part Number 3949247V Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Material plastic Wiring Wire leads Mounting Location Underside of cabinet top panel Function Confirms lid is closed before allowing the wash cycle to begin Repair Difficulty Easy — basic hand tools Quantity 1 lid switch (sold individually) Compatible Brands Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, KitchenAid Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Unplug your washer from the wall outlet and turn off the water supply before beginning. Wear work gloves. Remove the screws holding the access panel in place at the back of the machine, then carefully remove the panel and set it aside. Locate the lid switch assembly near the top, center of the washer's interior. Use a Phillips and flathead screwdriver to unscrew the three screws that hold the lid switch assembly in place. Disconnect the wire harness from the old lid switch and carefully remove it from the machine. Install the new 3949247 into the machine in the exact same manner the old switch was removed. Connect the wire harness to the new switch. Reattach the three screws to secure the switch in place. Replace the access panel and reattach its screws. Turn on the water supply and plug in the washer. Run a test cycle with the lid closed to confirm the washer starts and spins normally. Tools needed: Phillips head screwdriver, flat head screwdriver. Frequently Asked Questions My washer agitates but won't spin. Is this the part I need? Yes, this is a well-documented symptom of a failed lid switch. This switch tells the washer's control system that the lid is closed before allowing certain functions, and spin specifically often requires this signal — a failed switch commonly leaves agitation working while blocking spin. Why does this switch fail over time? The plastic on the switch's actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it during a cycle. Is this the same as the 3949238 switch? No, these are separate lid switch part numbers, despite the similar numbering. Our 3949238 listing is used on different models. Always confirm your exact part number from your washer's parts diagram or the sticker on your old switch before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the material, wiring, and switching function of the original 3949247V lid switch assembly used in compatible Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less