Search results for "dryer vent"

XPARTCO 279973 Dryer Thermostat Kit The XPARTCO 279973 is an aftermarket replacement dryer thermostat and thermal cut-off kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. The kit contains two components — the high-limit thermostat (L295-80F) and the thermal cut-off fuse — both located on the heating element housing. Together they protect the dryer's heating element from overheating: the high-limit thermostat monitors element temperature and cuts power if it exceeds safe levels, then resets when cooled. The thermal cut-off fuse is a backup one-time device that permanently opens the circuit if the thermostat fails to protect the element. Both parts are mounted on the side of the heating element housing and can be accessed through the dryer's back panel. The thermal cut-off fuse is a non-resettable one-time device — once it opens, it must be replaced. The 279973 kit includes both parts, an instruction sheet, and hardware. It directly replaces 3391913, 3404151, 3404152, 3977395, 8318314, 897710, 279973VP, AP3094323, and several additional cross-reference numbers. Note: this kit is for electric dryers only. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO 279973 Dryer Thermostat Kit fixes Whirlpool-family electric dryers with no heat, overheating, or a dryer that shuts off too early. Kit includes the L295-80F high-limit thermostat (auto-reset, opens at 295°F) and the thermal cut-off fuse (352°F, one-time). Both mount on the heating element housing. Electric dryers only. Replaces 3391913, 3404151, 8318314, 897710, AP3094323. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. Common Problems This Kit Fixes Dryer produces no heat — thermal cut-off fuse or high-limit thermostat has failed Dryer overheats — clothes or drum too hot at the end of a cycle Dryer shuts off early before clothes are dry Dryer takes multiple cycles or very long time to dry clothes Repeated no-heat failures — underlying overheating condition affecting the element housing components Dryer tumbles normally but produces no heat at all What's in the Kit Part 1 of 2 High-Limit Thermostat (L295-80F) Opens at 295°F — cuts power to the heating element if temperature exceeds safe levels · Auto-resets when cooled · Located on the heating element housing · Should show closed continuity (near-zero resistance) at room temperature Part 2 of 2 Thermal Cut-Off Fuse (352°F) Opens at 352°F — one-time backup safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to protect it · Cannot be reset — must be replaced if blown · Should show closed continuity at room temperature when working Replaces Part Numbers This thermostat kit directly replaces the following OEM and cross-reference part numbers: 279973, 279973VP, 3391913, 3404151, 3404152, 3977395, 8318314, 897710, ER279973, PD00002626, EAP334387, AWP39286, AH334387, AP3094323, EA334387, PS334387. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (Duet, Cabrio, and standard series) Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Inglis electric dryers Roper electric dryers Admiral electric dryers Important: This kit is for electric dryers only. Gas dryers use a different burner assembly and require a different thermostat kit (XP6974 for Whirlpool-family gas dryers). Always verify your dryer type and model number before ordering. Also: if the thermal cut-off fuse has blown, always check for a clogged exhaust vent before replacing — a blocked vent is the most common root cause of overheating and repeated fuse failures. Key Features 2-part kit — high-limit thermostat and thermal cut-off fuse, both on the heating element housing High-limit thermostat (L295-80F) — opens at 295°F to cut element power, auto-resets when cooled Thermal cut-off fuse (352°F) — one-time backup safety device; permanently opens if thermostat fails to protect the element Both parts located on the heating element housing — accessible from the dryer back panel Replacing both together ensures complete thermal protection is restored on the element housing Replaces 3391913, 3404151, 8318314, 897710, AP3094323, and over 10 additional cross-reference numbers Electric dryers only — not for gas dryer models Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number 279973 Condition Aftermarket Replacement Application Electric Dryers Only Kit Includes 1x High-Limit Thermostat (L295-80F), 1x Thermal Cut-Off Fuse (352°F), hardware, instruction sheet High-Limit Thermostat Rating L295-80F — opens at 295°F, resets at 215°F — auto-resets Thermal Cut-Off Fuse Trip Temp 352°F — one-time, non-resettable Location Heating element housing (both parts) Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to expose the heating element housing. Both the high-limit thermostat and thermal cut-off fuse are mounted on the side of the heating element housing — the thermostat is typically the larger component and the thermal cut-off fuse is smaller. Test each component with a multimeter before removing (both should show closed continuity at room temperature; the failed one will read open). Photograph the wiring before disconnecting. Disconnect the wires, remove the mounting screws, and install the new components in the same positions. Reconnect the wires and mounting screws, reinstall the back panel, restore power, and run a test cycle to confirm heat. Tip: Before running the dryer, clean the full length of the exhaust duct — a clogged vent is the most common cause of overheating and a blown thermal cut-off fuse. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter. Frequently Asked Questions What is the difference between the high-limit thermostat and the thermal cut-off fuse in this kit? The high-limit thermostat (L295-80F) is a resettable safety switch that opens at 295°F to cut power to the heating element and resets automatically when the temperature drops. It is the primary protection against overheating during normal operation. The thermal cut-off fuse is a one-time backup device rated at 352°F — it permanently opens the circuit if the heating element temperature climbs beyond the point the thermostat should have caught. Once the cut-off fuse opens, it must be replaced; it does not reset on its own. If the cut-off fuse has blown, it usually means the high-limit thermostat also failed to do its job and should be replaced at the same time — which is exactly what this kit provides. How do I test these parts with a multimeter? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect each component from the wiring and probe both terminals with a multimeter set to continuity or resistance mode. At room temperature, both the high-limit thermostat and the thermal cut-off fuse should show closed continuity (near-zero resistance). Any component that reads open circuit (no continuity) has failed and needs to be replaced. The thermal cut-off fuse reads open even after it cools — it is non-resettable. The high-limit thermostat may read open at room temperature if it has failed internally rather than by an overheat trip. How is the 279973 kit different from the XP6974 thermostat kit? The 279973 is a 2-part kit — high-limit thermostat and thermal cut-off fuse — designed specifically for the heating element housing of Whirlpool-family electric dryers. The XP6974 is a 4-part kit — cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off — designed for Whirlpool-family gas and electric dryers, covering both the exhaust duct components and the burner/element housing components. If your electric dryer is showing no-heat and you need only the heating element housing components, the 279973 kit covers exactly those two parts. If you want to replace all thermal components in one repair, the XP6974 covers a broader set. Why does the thermal cut-off fuse keep blowing? If the thermal cut-off fuse blows repeatedly after replacement, it almost always means there is an underlying overheating condition causing the heating element housing to run hotter than it should. The most common cause is a clogged or restricted exhaust vent — lint accumulation in the duct reduces airflow, trapping heat inside the dryer cabinet and around the element. Other causes include a failed cycling thermostat that is not regulating element temperature correctly, a stuck heating element relay, or a dryer in an enclosed space with inadequate ventilation. Always clean the full exhaust duct and check the cycling thermostat (WP3387134) before replacing the thermal cut-off fuse a second time. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature ratings and specifications of the original 279973 high-limit thermostat and thermal cut-off fuse kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit The AGM30045804 is a genuine LG OEM high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does. Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335. Quick Answer The AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step. What's In The Kit Component Function High-Limit Thermostat Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools. Thermistor (with wire harness) Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle. Common Problems This Kit Fixes Dryer overheating, sometimes scorching or damaging clothing Dryer running with little or no heat Inconsistent drying times — cycle shuts off too early or runs longer than necessary Temperature-related error code displayed on the control panel Clothes remaining damp after a full drying cycle High-limit thermostat that keeps tripping repeatedly Dryer that has already had its high-limit thermostat replaced once but the problem returned Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers: AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform. Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order. Key Features Genuine LG OEM part — factory-specified resistance values and switch thresholds Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms Thermistor ships with its wire harness included High-limit thermostat resets automatically after tripping — no replacement needed after each trip Direct drop-in replacement for both original components Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335 Compatible with LG and select Kenmore and GE-branded LG-built dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AGM30045804 Part Type Dryer High-Limit Thermostat and Thermistor Kit Condition Genuine OEM Brand LG Kit Contents High-limit thermostat + thermistor with wire harness Thermistor Location Blower housing High-Limit Thermostat Type Automatically resetting Repair Difficulty Easy to Moderate — 30 to 60 minutes Compatible Brands LG, select Kenmore, GE (LG-built models) Installation Notes ⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead? This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit. What's the difference between the thermistor and the high-limit thermostat? The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating. My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing? Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same resistance values, switch threshold, and wire harness configuration as the high-limit thermostat and thermistor originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 134719300 Dryer Drum Belt The XPARTCO 134719300 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. The drum belt is a critical component that connects the motor pulley to the drum, enabling the drum to rotate during drying cycles. The belt wraps around the drum circumference, passes over an idler pulley (which maintains tension), and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail due to normal wear from friction and heat, cracking or fraying from age and repeated flexing, stretching that reduces tension and causes slipping, contamination from lint buildup, or sudden breakage from overloading or mechanical stress. Constructed from durable black rubber with reinforced fabric or cord embedded inside for strength and flexibility, designed to withstand thousands of hours of operation under high temperatures and constant friction. Dimensions: 90"L x 5/16"W x 1/8"H with 5 ribs and 4 grooves. It directly replaces 134719300, 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294. Important: install the belt with the grooves facing DOWN, against the drum. Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair since both wear together. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 134719300 Dryer Drum Belt fixes Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, the dryer makes loud squealing or squeaking noises, or clothes take too long to dry. 90"L x 5/16"W x 1/8"H. 5 ribs, 4 grooves. Black rubber. Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, PS2349294. Install with grooves facing DOWN against the drum. Often paired with idler pulley (134793500/134793511, sold separately). Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Dryer won't start — belt switch (on some models) tripped by broken belt Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — clear sign the belt has snapped Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: 134719300, 137315300, 7134719300, AFR14405, AP4368788, EAP2349294, LB5300, PD00000843, PS2349294. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Frigidaire dryers (select electric and gas models) — including FDEB34RGS1/GS2, FDEB55RGS0/GS1, FDER436RHS0 and related models Electrolux dryers (select models) Crosley dryers — CDE4500KW0, CDE4700LB0/LW0, CDE4701QW0, CDE7300RW0, CDE7400QW0/QW1, CDE7500KB0/KR0/KW0, CDE7700LR0/LW0, CDEC450KW0, CDEC750KW0, CDG4500KW0, CDG4700LB0/LW0, CDG4701QW0, CDG7300RW0/RW1, CDG7400QW0, CDG7500KB0/KR0/KW0, CDG7700LW0/LW1 series Kenmore / Sears dryers — select Frigidaire/Electrolux-built models White-Westinghouse dryers (select models) Gibson dryers (select models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler pulley (134793500 or 134793511, sold separately) — it wears from the same friction cycles as the belt, and if it's rough, seized, or noisy, the new belt will wear out prematurely. Many customers replace both together as a matched set. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction with reinforced fabric/cord for strength and flexibility Engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 90" L x 5/16" W x 1/8" H with 5 ribs and 4 grooves Install with grooves facing DOWN against the drum for proper engagement Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294 Compatible with Frigidaire, Electrolux, Crosley (CDE/CDG series), Kenmore, White-Westinghouse, and Gibson dryers Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP134719300 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Frigidaire/Electrolux platform) Length 90" Width 5/16" Thickness 1/8" Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber with reinforced fabric/cord Installation Orientation Grooves face DOWN against the drum Often Paired With Idler Pulley (134793500 or 134793511, sold separately) Compatible Brands Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, Gibson Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooves Face DOWN Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Remove the top and/or front panels of the dryer to access the drum — the specific procedure varies by model, but typically involves removing 2–4 screws under the top edge or lint trap area, then lifting or tilting the top panel forward. Once the top is off, disconnect the door switch wire harness and lift the front panel free. This exposes the drum, motor, and idler pulley. Photograph the belt routing before disassembly if any belt fragments remain — you'll need to match the routing pattern with the new belt. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley. Support the drum from underneath (a wooden block or two can help hold it in position). Route the new 134719300 belt around the drum in the same position as the old belt — approximately 4-6 inches from the front lip of the drum. Install with the grooves facing DOWN, against the drum surface — this is essential for proper engagement with the motor pulley. From under the drum, route the belt over the idler pulley and around the drive motor pulley in a Z-shape. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly. Verify the drum rotates freely without binding — if it doesn't, the belt is twisted, kinked, or misrouted; fix it before reassembling. Reinstall the front and top panels, reconnect the door switch, restore power, and run a test cycle to confirm normal operation. Tools needed: Phillips screwdriver, wooden block, side cutters (for removing broken belt fragments), flathead screwdriver, work gloves. Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming/whirring) but the drum stays still, the belt has almost always snapped or is slipping badly. To confirm without opening the dryer: reach in through the door and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum bearings or rollers could be the issue. In either case, opening the dryer to inspect the belt visually is the definitive check — a snapped belt will be lying in the bottom of the cabinet. Why do I have to install the belt with grooves facing down? The dryer's motor pulley is a smooth, un-grooved cylinder — the belt runs against it with the flat (smooth) side. The drum, on the other hand, needs the grooves to positively engage and drive without slipping under load. So the grooved side faces the drum (down when you're routing the belt around the drum from above), and the smooth side wraps around the motor pulley and idler pulley. Installing the belt backwards with grooves facing up will cause the belt to slip against the drum immediately and can burn out the new belt within a few minutes of operation. Should I replace the idler pulley at the same time? Yes, it's strongly recommended. The idler pulley (134793500 or 134793511 on many compatible dryers) maintains constant tension on the drum belt as the drum rotates. It wears from the same friction cycles as the belt — when the belt fails, the idler pulley bearings have typically also been stressed and are near end-of-life. Since the dryer is already open and the pulley is right there next to the belt, replacing both saves you a repeat repair when the pulley fails a few months later. Signs of a worn idler pulley: rough or noisy rotation when spun by hand, visible wear grooves, or seized bearings. What's the difference between 134719300 and 137315300? These are the same drive belt across production revisions. 137315300 was a Frigidaire OEM part number and 134719300 is the current cross-referenced part number that covers the same belt. Both are physically and functionally identical — if your dryer's parts diagram shows either number, this listing is the correct replacement. LB5300 and 7134719300 are additional catalog references for the same belt. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable rubber with reinforced fabric/cord to match the dimensions (90"L x 5/16"W x 1/8"H), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original 134719300 drum belt used in compatible Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

17438000001584 Genuine OEM Midea Dryer Belt Safety Switch The 17438000001584 is a Genuine OEM Midea replacement belt safety switch compatible with select Midea, Criterion, and Insignia electric and gas dryers. This safety switch is positioned near the drive belt and tensioner pulley assembly, where it monitors belt-related conditions and interrupts electrical flow to the motor or heating circuit if a fault or unsafe condition is detected — such as a broken or severely slipped drive belt. This is a key safety mechanism: if the belt fails and the drum can no longer be safely driven, this switch helps prevent the motor from continuing to run unsafely or the heater from continuing to operate without normal airflow from drum rotation. When this switch fails, the dryer may not start, may shut off unexpectedly during operation, or may fail to heat even though other components test correctly. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438000001584 measures 2"L x 2"W x 3"H and weighs approximately 1 oz. It is found on the same parts diagram as the drive belt, tensioner pulley assembly, and drum support components on compatible models. Installs in 30–45 minutes with basic hand tools. Quick Answer The 17438000001584 Genuine OEM Midea Dryer Belt Safety Switch fixes Midea, Criterion, and Insignia dryers that won't start, shut off unexpectedly during operation, or fail to heat despite other components testing normally. Mounted near the drive belt and tensioner pulley assembly — interrupts power if a fault or unsafe belt condition is detected. Dimensions: 2"L x 2"W x 3"H, approx. 1 oz. Genuine OEM. Compatible with Midea MLG45N3BMG, Criterion CDG41N1AW, CDG45N1AW, and related Midea-platform dryer models. Common Problems This Part Fixes Dryer not starting — safety switch not signaling normal belt/drive conditions Dryer shutting off unexpectedly partway through a cycle Dryer not heating despite the heating element, thermostat, and other components testing normal Dryer behaving erratically after a drive belt failure or replacement Intermittent power interruption during operation traced to this switch area Switch contacts failing continuity test with a multimeter Replaces Part Numbers This belt safety switch directly replaces the following part number: 17438000001584, AP7157511, PS18188483 This is the Midea manufacturer part number used across multiple Midea, Criterion, and Insignia dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This belt safety switch is compatible with select Midea, Criterion, and Insignia dryers, including: Midea MLG45N3BMG gas dryer Midea MLG45N1BWW, MLG45N3BWW, and related MLG gas dryer series Midea MLE series electric dryers (select models) Criterion CDG41N1AW, CDG45N1AW gas dryers (air vent series) Insignia electric and gas dryers built on the Midea platform (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Safety switch mounted near the drive belt and tensioner pulley assembly Interrupts electrical flow to the motor or heating circuit if a fault or unsafe belt-related condition is detected Compact design: 2"L x 2"W x 3"H, approximately 1 oz Compatible with Midea MLG/MLE series, Criterion CDG series, and Insignia Midea-built dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number 17438000001584 Part Type Dryer Belt Safety Switch Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Dimensions 2"L x 2"W x 3"H Weight Approximately 1 oz Location Near drive belt and tensioner pulley assembly Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum, drive belt, and tensioner pulley assembly. Locate the belt safety switch in this area — refer to your model's parts diagram to confirm its exact mounting position, as it is positioned near the belt and tensioner pulley support. Photograph the wire connections before disconnecting. Disconnect the wires from the old switch, remove the mounting screw or clip, and pull the switch free. Install the new 17438000001584 switch in the same position, secure the mounting hardware, and reconnect the wires. While this area is open, it's a good time to inspect the drive belt and tensioner pulley for wear, since this switch is related to belt operation. Reassemble the front panel and top panel in reverse order. Restore gas and power, and run a test cycle to confirm the dryer starts and runs normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the belt safety switch do? The belt safety switch monitors belt-related conditions near the drive belt and tensioner pulley assembly and interrupts electrical flow to the motor or heating circuit if it detects a fault or unsafe condition — such as a broken or badly slipped drive belt. This is a protective measure: if the belt has failed and the drum can no longer be driven normally, the switch helps prevent continued unsafe operation of the motor or heater. It works alongside other safety components in the dryer (like the door/cover switch and thermal limiters) as part of an overall safety system. My dryer just had a belt replacement and now isn't working right — could this switch be involved? It's possible. Since this switch is positioned near the belt and tensioner pulley assembly, it can be disturbed, dislodged, or its connector improperly reseated during a belt replacement. If your dryer is behaving erratically after a recent belt repair — failing to start, shutting off, or not heating — check that this switch's connector is fully seated and that the switch itself wasn't damaged during the repair. If the connector is good and the switch tests as an open circuit with a multimeter, it has failed and needs replacement. How do I test if this safety switch has failed? Unplug the dryer, disconnect the switch's wire connector, and set your multimeter to continuity mode. With the belt and tensioner mechanism in their normal operating position, the switch should show closed continuity (allowing current to flow). If the switch shows an open circuit when it should be closed, it has failed and needs replacement. Always refer to your specific model's wiring diagram to confirm the expected switch state, since exact behavior can vary by dryer model. Does this switch fit Insignia and Criterion dryers as well as Midea? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in certain configurations are manufactured by Midea and use the same internal components, including this belt safety switch. Confirmed Criterion models include the CDG41N1AW and CDG45N1AW gas dryers. Always verify your specific model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same belt safety switch installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool WP3387134 Dryer Cycling Thermostat - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid Product Description Maintain optimal drying temperatures with the Genuine Whirlpool WP3387134 Dryer Cycling Thermostat. This OEM cycling thermostat is designed for select Whirlpool, Kenmore, Maytag, KitchenAid, and other dryers, regulating the heating element by cycling on at 155°F (68°C). It addresses issues like no heat, insufficient heat, overheating, or prolonged drying times, delivering reliable performance as an authentic Whirlpool part. Note: Includes one cycling thermostat. Disconnect power before installation. Check dryer venting and related components for optimal performance. Replaces part numbers: WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187, PD00002313, EAP11741405, WP3387134VP, AP6008270, PS11741405, L155-25F.  Compatibility: Compatible with models including but not limited to: Whirlpool: WED5500XW0, WED5600XW0, WED9400SW0, WGD5500XW0, WED5800BC0 Kenmore: 110.60022010, 110.68002010, 110.87872603 Maytag: MED6000XW0, MED7000XW0 KitchenAid: YKEHX01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, and other dryers. 🔥 Specifications: OEM cycling thermostat, cycles on at 155°F (68°C). 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, insufficient heat, overheating, or prolonged drying times. Product Specification Part Number: Genuine Whirlpool WP3387134 Component Type: Dryer cycling thermostat Material: Metal and plastic Electrical Specs: Cycles on at 155°F (68°C). Mounting: Screw-mounted near heater housing or exhaust duct Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO WE1M1002 Dryer Fuse, 30 AMP 120V The XPARTCO WE1M1002 is an aftermarket replacement power fuse for GE and Hotpoint dryers, commonly used on GE's commercial and stacked laundry center dryer models. This is a CCMR-class fuse — a current-limiting, fast-acting power fuse — and it plays a fundamentally different protective role than a thermal cut-off fuse. Rather than reacting to excess heat from restricted airflow, this fuse reacts to electrical faults: if the dryer experiences a short circuit or a current overload beyond what the wiring is rated to handle, this fuse opens the circuit immediately to prevent damage to the dryer's electrical components. Rated 30A, 120V, measuring approximately 3/8"H x 3/8"W x 1-1/2"D. Because this fuse protects against electrical faults rather than heat buildup, a blown WE1M1002 points toward a different diagnostic path than a thermal fuse would: rather than checking the exhaust venting, the more relevant checks are the dryer's wiring, connections, and any component that may have shorted internally. A blown fuse produces a complete loss of power to the dryer — no lights, no display, no response to any control. It directly replaces WE01M1002, 1974262, AP5270172, PS3496852, and EAP3496852. Quick Answer The XPARTCO WE1M1002 Dryer Fuse fixes GE and Hotpoint dryers, including commercial and stacked laundry center models, that have completely lost power — no lights, no display, no response to any control. CCMR-class, 30A, 120V. Replaces WE01M1002, 1974262, AP5270172, PS3496852, EAP3496852. This is a power/overcurrent fuse, not a thermal cut-off fuse — if it's blown, check the dryer's wiring and electrical connections for a short or fault rather than the exhaust venting. Common Problems This Part Fixes Dryer has completely lost power — no lights, no display, no response to any control Dryer that stopped working suddenly, especially after an electrical fault or short Dryer that trips repeatedly after a wiring or component issue elsewhere in the unit Continuity test shows an open circuit across the old fuse Complete electrical dead-out on a commercial or stacked laundry center dryer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer fuse directly replaces the following OEM and cross-reference part numbers: WE1M1002, 1974262, PD00029481, EAP3496852, AGE25598, AH3496852, EA3496852, AP5270172, PS3496852 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This fuse is compatible with select GE dryers, and also fits select Hotpoint and RCA dryers, including commercial and stacked laundry center models such as: DCCB330EJ3WC, DCCB330EJ4WC, DCCB330GJ3WC, DCCB330GJ4WC DDC4400T5WH DISR333FCGWW, DISR333FCHWW, DISR333FGDWW, DISR333FGEWW DISR473CG8WW, DISR473CGBWW, DISR473DGEWW, DISR473DGFWW DIST333JTMWW, DIST333JTNWW DMCD330EJ3WC, DMCD330EJ4WC, DMCD330GJ3WC, DMCD330GJ4WC DNCD450EGBWC, DNCD450EGCWC, DNCD450GGCWC 2661532210, 2661532211, 2671532210 Note: This part is distinct from a thermal cut-off fuse used on residential dryer platforms — it's a CCMR-class power fuse most commonly found on GE's commercial and stacked laundry center dryer models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement CCMR-class power fuse — protects against electrical faults and current overload Resolves "complete loss of power" symptoms caused by an electrical short or overload Rated 30A, 120V Compact size: approximately 3/8"H x 3/8"W x 1-1/2"D Direct drop-in replacement — no modification required Replaces WE01M1002, 1974262, AP5270172, PS3496852, and EAP3496852 Compatible with GE, Hotpoint, and RCA dryers, including commercial and stacked laundry center models Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WE1M1002 OEM Part Number WE1M1002 Part Type Dryer Power Fuse (CCMR Class) Condition Aftermarket Replacement Current Rating 30A Voltage 120V Fuse Class CCMR (current-limiting, fast-acting) Protects Against Electrical short circuits and current overload Resettable No — one-time use, must be replaced once blown Dimensions 3/8"H x 3/8"W x 1-1/2"D Quantity 1 fuse Compatible Brands GE, Hotpoint, RCA Installation Notes ⚠️ Unplug Dryer Before Starting — Investigate The Cause Of The Short Before Replacing Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Locate the fuse holder inside the dryer's electrical panel or control housing — access varies by model, so consult your unit's service diagram. Before removing the old fuse, visually inspect nearby wiring and connections for signs of a short, such as scorching, melted insulation, or a loose connection, since this fuse type responds to electrical faults rather than heat buildup from airflow issues. Test the old fuse with a multimeter to confirm it's open (no continuity) before assuming it needs replacement. Remove the old fuse from its holder and install the new WE1M1002 in the same position, making sure it seats fully and securely. Restore power and test the dryer to confirm normal operation. If the new fuse blows again shortly after installation, stop and have a qualified technician diagnose the underlying electrical fault before continuing, since repeatedly replacing this fuse without addressing the root cause can be a sign of a more serious wiring or component issue. Tools needed: fuse puller or needle-nose pliers, multimeter, work gloves. Frequently Asked Questions How is this different from a thermal cut-off fuse? They protect against completely different problems. A thermal cut-off fuse reacts to excess heat, usually from restricted exhaust airflow, and its diagnosis typically starts with checking the venting. This WE1M1002 is a CCMR-class power fuse that reacts to electrical faults — a short circuit or current overload — and its diagnosis should focus on the dryer's wiring and electrical connections rather than the exhaust system. My dryer has completely no power at all. Is this the fuse? It's a strong possibility, especially if this occurred suddenly or followed any unusual electrical event. Since this fuse protects the dryer's power circuit broadly, a blown fuse can result in a total loss of power — no lights, no display, nothing. Test it with a multimeter for continuity before replacing to confirm. I replaced the fuse and it blew again right away. What should I do? This is a sign that the underlying electrical fault that blew the original fuse hasn't been addressed. Unlike a thermal fuse blowing from airflow restriction, a repeat blow on this type of fuse points to an ongoing short circuit or wiring problem elsewhere in the dryer. Stop and have a qualified technician trace and repair the fault rather than continuing to replace fuses, since the underlying issue could pose a safety risk if left unresolved. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical rating and fuse class of the original WE1M1002 power fuse used in compatible GE, Hotpoint, and RCA dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

137292700 Genuine OEM Dryer Drum Belt Product Title 137292700 Dryer Genuine OEM Drum Belt - Compatible with Frigidaire, Electrolux, Kenmore Dryers Product Description Keep your dryer running smoothly with the Genuine OEM 137292700 Dryer Drum Belt from Parts-O-Matic. This Genuine OEM belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum to ensure efficient tumbling and drying. Compatible with select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryers, this belt fixes issues like failure to tumble, unusual noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryer models. 🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying. 💰 Cost-Effective Alternative: Genuine OEM part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair. 🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production. Compatibility: Compatible with models including but not limited to: Frigidaire: FEX831FS2, FEQ332ES0, FER231AS2, AGQ6000ES2 Electrolux: EIMED55IIW0, EIMED60JIW0 Kenmore: 417.91702001, 417.97812700, 417.97812702 Replaces part numbers: 137292700, 134163500, 134503900, 5303283287, AH3408299, EA3408299, AP4565702, PS3408299. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension. Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Caution: Avoid stretching the belt during installation, as this can reduce its lifespan. Shop Parts-O-Matic for Genuine OEM appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

XPARTCO DC96-00887C - DC47-00018A Dryer Thermostat Set The XPARTCO DC96-00887C / DC47-00018A is an aftermarket replacement 2-piece thermal protection set for Samsung and select Kenmore electric dryers. These two components sit in different locations along the same heating circuit and guard against overheating in different ways. The DC47-00018A is a true cycling high-limit thermostat — it opens at approximately 260°F to cut power to the heating element, then automatically closes again once the temperature drops to around 210°F, letting the dryer resume heating without any part replacement needed. The DC96-00887C, despite frequently being labeled a "thermostat" by third-party sellers, is actually a one-time thermal fuse mounted with its bracket on the blower housing — once it opens from excess heat, it stays open permanently and must be physically replaced. Because these two parts monitor different points in the same circuit, they tend to be replaced together when a dryer has been running hot: if the high-limit thermostat has been cycling excessively or failed to catch a temperature spike, the downstream thermal fuse can end up blowing as the last line of defense. Symptoms of failure in this circuit include no heat or insufficient heat, drying that takes too long, the dryer shutting off too soon, or the timer failing to advance. It directly replaces DC96-00887A, AP5966894, 2074129, AP4207819, PS4216838, EAP4216838, WP35001193, 35001193, PS11741822, PS11741829, AP6008689 (DC96-00887C); and 35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682, WP35001092 (DC47-00018A). Quick Answer The XPARTCO DC96-00887C - DC47-00018A Dryer Thermostat Set fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, premature shutoff, or a timer that won't advance. Set includes the DC47-00018A cycling high-limit thermostat (260°F open / 210°F reset) and the DC96-00887C thermal fuse with bracket. Replaces the full cross-reference sets listed below for both parts. Despite common marketplace labeling, the DC96-00887C is a one-time thermal fuse, not a resettable thermostat — it must be replaced once it blows, while the DC47-00018A resets itself automatically. What's In This Set Component Type Function DC47-00018A Cycling High-Limit Thermostat Opens at ~260°F to cut heat, automatically resets and closes again around 210°F. No replacement needed after each trip. DC96-00887C Thermal Fuse (with bracket) Mounted on the blower housing. Permanently opens if temperature exceeds safe limits. Cannot reset — must be replaced once blown. Common Problems This Set Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat/thermal fuse set directly replaces the following OEM and cross-reference part numbers: DC96-00887C, DC96-00887A, AP5966894, PS4276292, WP35001193, 35001193, AP6008689, PS11741829, DC47-00018A, AP4201898, PS4205217, 35001092, WP35001092 AP6008682, PS11741822, EXPDC47-00018A, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This set is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note: Always verify your full model number before ordering, since Samsung uses several different thermal protection components across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features 2-piece set covering both the cycling high-limit thermostat and the blower housing thermal fuse DC47-00018A thermostat opens at approximately 260°F and resets automatically around 210°F DC96-00887C thermal fuse ships with its mounting bracket included Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Addresses two failure points in the same overheat-protection circuit at once No special tools required for installation Replaces the full cross-reference sets for both DC96-00887C and DC47-00018A listed above Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Set Contents 1x DC47-00018A high-limit thermostat, 1x DC96-00887C thermal fuse with bracket Condition Aftermarket Replacement Application Samsung Electric Dryers DC47-00018A Type Automatically resetting, cycling high-limit thermostat DC47-00018A Open Temperature ~260°F DC47-00018A Reset Temperature ~210°F DC96-00887C Type One-time thermal fuse — non-resettable DC96-00887C Location Blower housing Repair Difficulty Easy to Moderate — no special tools required Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Note Which Component Goes Where Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the blower housing and heater duct assembly where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermal fuse and thermostat can look similar at a glance and are easy to install in the wrong position. Test each old component with a multimeter for continuity if you want to confirm which has actually failed before replacing both — the DC47-00018A thermostat and DC96-00887C fuse can each be checked this way. Remove each old component from its mounting position, noting orientation and location, and disconnect its wiring. Install the DC47-00018A thermostat and the DC96-00887C fuse (with its bracket) from this set in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), multimeter (recommended), work gloves. Frequently Asked Questions Is DC96-00887C really a thermostat, or something else? Different sellers call it different things. This is a genuinely common point of confusion in the marketplace, and it's worth clearing up: DC96-00887C is actually a one-time thermal fuse mounted with its bracket on the blower housing, even though many third-party listings label it a "thermostat." The distinction matters for how you diagnose and handle it — once this fuse blows from excess heat, it stays open permanently and must be physically replaced, unlike a true thermostat (like the DC47-00018A in this same set) which resets itself automatically once things cool down. Why replace both parts together instead of just the one that failed? These two components sit at different points in the same overheat-protection circuit, and a problem with one often puts stress on the other. If the high-limit thermostat has been cycling excessively or didn't catch a temperature spike in time, the downstream thermal fuse can end up blowing as the last line of defense. Replacing both together addresses the full circuit rather than risking a second failure and a second repair shortly after. My dryer shuts off before the load is fully dry. Is that this set? It's a strong possibility. If the high-limit thermostat is tripping prematurely — opening at a lower temperature than it should, or failing to reset properly — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat set addresses. Is this an OEM or aftermarket set? This is an aftermarket replacement set built to OEM-equivalent quality standards. It is not a genuine Samsung OEM set, but each component is manufactured to match the electrical specifications, opening/reset temperatures, and mounting configuration of the original DC96-00887C thermal fuse and DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE03X29897 Dryer Drum Belt Product Title XPARTCO WE03X29897 Dryer Drum Belt - Compatible with GE, Hotpoint, Kenmore Dryers Product Description Ensure your dryer tumbles smoothly with the XPARTCO WE03X29897 Dryer Drum Belt from Parts-O-Matic. This high-quality aftermarket belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum for efficient drying. Compatible with select GE, Hotpoint, RCA, and Kenmore dryers, this belt resolves issues like failure to tumble, squealing or thumping noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select GE, Hotpoint, RCA, and Kenmore dryer models. 🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying. 💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair. 🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production. Compatibility: Compatible with models including but not limited to: GE: GTD33EASK0WW, GTD42EASJ2WW, GTD65EBSJ0WS, GTX33EASK0WW Hotpoint: HTX21EASK0WW, HTX24EASK0WS Kenmore: 363.61542412, 363.71542410 Replaces part numbers: WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE03X29897-30PK, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, PS16542496. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension (e.g., WE12X83). Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Caution: Avoid stretching the belt during installation, as this can reduce its lifespan. Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO DC47-00016A Dryer Thermal Fuse The XPARTCO DC47-00016A is an aftermarket replacement thermal fuse for Samsung dryers. Mounted on the blower housing near the heat source, this fuse is a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb dangerously high — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to the dryer. That's why a blown thermal fuse produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. This fuse terminates in 1/4" male spade connectors for a direct plug-in fit. Unlike a thermostat, a thermal fuse cannot be reset once it blows — it must be replaced. Critically, a blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what the fuse is designed to react to. A failing thermistor can also cause repeated fuse blows, since the two work together to regulate temperature. It directly replaces 2068545, AP4201894, AP4201899, PS4205213, EAP4205213, PS2038378, PS2038533, and 35001087. Quick Answer The XPARTCO DC47-00016A Dryer Thermal Fuse fixes Samsung dryers that won't start at all — no lights, no tumble, no response to any button — after overheating from restricted airflow. 1/4" male spade terminals. Replaces 2068545, AP4201894, AP4201899, PS4205213, EAP4205213, PS2038378, PS2038533, 35001087. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after a load felt unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Dryer that recently smelled like burning or overheating before failing Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal fuse directly replaces the following OEM and cross-reference part numbers: DC47-00016A, L0016A, AP4201894, PS4205213, AP6008681, EAP4205213, OEM12605691, EAP11741821, ASM868996, PD00005341, PD00003747, PS11741821, 35001087, WP35001087. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Samsung dryers, and also fits select LG and Kenmore dryers built on a compatible platform, including model numbers such as: DV209AEW/XAA, DV210AEW, DV210AEW/XAA DV218AEB/XAA, DV218AEW/XAA, DV219AEW/XAA, DV220AEW, DV220AEW/XAA DV330AEW, DV350AEW/XAA, DV419AEW/XAA Note: This fuse is commonly paired with a matching thermistor (DC32-00007A) and thermostat (DC96-00887A / DC47-00018A), and manufacturer guidance recommends replacing the thermistor at the same time as the fuse, since the two work together and a failing thermistor is a common cause of repeated fuse blows. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement thermal fuse — one-time safety device that cuts power if the dryer overheats Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse 1/4" male spade terminal connectors for a direct plug-in electrical fit Mounts to the blower housing near the heat source Replaces 2068545, AP4201894, AP4201899, PS4205213, EAP4205213, PS2038378, PS2038533, and 35001087 Compatible with select Samsung, LG, and Kenmore dryers Aftermarket replacement built to OEM-equivalent quality standards Quick, simple repair — no special tools required beyond a basic screwdriver Product Specifications Part Number DC47-00016A OEM Part Number DC47-00016A Part Type Dryer Thermal Fuse (Thermal Cut-Off) Condition Aftermarket Replacement Location Blower housing, near the heat source Terminals 1/4" male spade connectors Resettable No — one-time use, must be replaced once blown Companion Parts Thermistor DC32-00007A, thermostat DC96-00887A / DC47-00018A Quantity 1 thermal fuse Compatible Brands Samsung, LG, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted, usually alongside the thermistor. Photograph the wiring before disconnecting the spade terminals from the old fuse. Remove the mounting screw holding the fuse in place and pull it free, disconnecting both spade terminal wires. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new DC47-00016A in the same mounting position, reconnect both spade terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the thermistor and thermostat checked as well, since a failing thermistor can also trigger repeated fuse blows. Can I just reset the thermal fuse instead of replacing it? No. Unlike a thermostat, a thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. Should I replace the thermistor at the same time as the fuse? It's worth strongly considering, and it's a common manufacturer recommendation. The thermistor and thermal fuse work together to manage temperature, and a failing thermistor can cause the dryer to run hotter than it should, leading directly to repeated fuse blows. Replacing both together, especially if your dryer has blown this fuse more than once, addresses the more likely root cause rather than just the symptom. My clothes came out extremely hot right before the dryer died. Is that related? Yes, this is a classic warning sign. Clothes coming out unusually hot indicates the dryer was already running hotter than normal, which is exactly the condition that leads to a blown thermal fuse. If you noticed this before the dryer stopped working, it strongly points to a ventilation or airflow problem that should be fully addressed before running the dryer again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications, spade terminal connections, and mounting configuration of the original DC47-00016A thermal fuse used in compatible Samsung, LG, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less