5304511380 Replacement Dryer Drum Belt - Compatible with Frigidaire, Electrolux
Product Description
Ensure your dryer’s drum rotates smoothly with the 5304511380 Replacement Dryer Drum Belt. This replacement part is designed for select Frigidaire, Electrolux, and compatible dryers, connecting the motor to the drum to enable proper tumbling during drying cycles. It addresses issues like the drum not spinning, unusual noises, or failure to start, offering a cost-effective alternative to OEM parts with equivalent performance.
Note: Includes one dryer drum belt. Disconnect power before installation. Inspect the idler pulley and motor pulley for wear to prevent repeat failures. This is a replacement part designed to match OEM specifications.
Replaces part numbers: 5304511380, 4584320, PD00063076, EAP12176502, AP6261662, PS12176502.
Compatibility:
Compatible with models including but not limited to:
Frigidaire: FASE7073LW0, FFQE5000QW0, FARE4044MW0, FAQE7077KR0, FARE1011MW0, FFSE5115PA0
Electrolux: EIED50LIW0, EIMED60JIW0, EIMED55IIW0
Kenmore: 417.81122310, 417.91122310
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, and compatible Kenmore dryers.
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires screwdriver, wrench, work gloves; typically installed in 20–40 minutes with YouTube video guidance.
🛡️ Effective Fixes: Resolves drum not spinning, noisy operation, or failure to start.
Product Specification
Part Number: XP5304511380
Component Type: Dryer drum belt
Material: Durable rubber
Mounting: Loops around drum, motor pulley, and idler pulley
Operating Conditions: Suitable for high-tension dryer drum systems
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Tip: Access the drum by removing the dryer’s top or front panel; thread the belt through the idler pulley and around the motor pulley, ensuring proper tension. Watch YouTube videos for step-by-step guidance. Check idler pulley and motor pulley for wear to avoid premature belt failure.
Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running smoothly today!
Add to cart now for a budget-friendly fix!
XPARTCO 134719300 Dryer Drum Belt
The XPARTCO 134719300 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. The drum belt is a critical component that connects the motor pulley to the drum, enabling the drum to rotate during drying cycles. The belt wraps around the drum circumference, passes over an idler pulley (which maintains tension), and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail due to normal wear from friction and heat, cracking or fraying from age and repeated flexing, stretching that reduces tension and causes slipping, contamination from lint buildup, or sudden breakage from overloading or mechanical stress.
Constructed from durable black rubber with reinforced fabric or cord embedded inside for strength and flexibility, designed to withstand thousands of hours of operation under high temperatures and constant friction. Dimensions: 90"L x 5/16"W x 1/8"H with 5 ribs and 4 grooves. It directly replaces 134719300, 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294. Important: install the belt with the grooves facing DOWN, against the drum. Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair since both wear together. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 134719300 Dryer Drum Belt fixes Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, the dryer makes loud squealing or squeaking noises, or clothes take too long to dry. 90"L x 5/16"W x 1/8"H. 5 ribs, 4 grooves. Black rubber. Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, PS2349294. Install with grooves facing DOWN against the drum. Often paired with idler pulley (134793500/134793511, sold separately).
Common Problems This Part Fixes
Dryer drum doesn't turn — motor runs but drum stays still (belt snapped)
Dryer drum rotates slowly or intermittently — belt worn or slipping
Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned
Dryer won't start — belt switch (on some models) tripped by broken belt
Clothes taking much longer than normal to dry — drum not tumbling clothes effectively
Visible cracks, fraying, or glazing on the belt surface
Belt broken completely — often heard as a loud snap during operation
Drum spins freely by hand with no resistance — clear sign the belt has snapped
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
134719300, 137315300, 7134719300, AFR14405, AP4368788, EAP2349294, LB5300, PD00000843, PS2349294.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This dryer drum belt is compatible with select dryers from the following brands:
Frigidaire dryers (select electric and gas models) — including FDEB34RGS1/GS2, FDEB55RGS0/GS1, FDER436RHS0 and related models
Electrolux dryers (select models)
Crosley dryers — CDE4500KW0, CDE4700LB0/LW0, CDE4701QW0, CDE7300RW0, CDE7400QW0/QW1, CDE7500KB0/KR0/KW0, CDE7700LR0/LW0, CDEC450KW0, CDEC750KW0, CDG4500KW0, CDG4700LB0/LW0, CDG4701QW0, CDG7300RW0/RW1, CDG7400QW0, CDG7500KB0/KR0/KW0, CDG7700LW0/LW1 series
Kenmore / Sears dryers — select Frigidaire/Electrolux-built models
White-Westinghouse dryers (select models)
Gibson dryers (select models)
Note: When you replace the drum belt, this is also the ideal time to inspect the idler pulley (134793500 or 134793511, sold separately) — it wears from the same friction cycles as the belt, and if it's rough, seized, or noisy, the new belt will wear out prematurely. Many customers replace both together as a matched set. Always verify your dryer model number before ordering.
Key Features
Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles
Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure
Durable black rubber construction with reinforced fabric/cord for strength and flexibility
Engineered to withstand thousands of hours of high-temperature, high-friction operation
Dimensions: 90" L x 5/16" W x 1/8" H with 5 ribs and 4 grooves
Install with grooves facing DOWN against the drum for proper engagement
Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294
Compatible with Frigidaire, Electrolux, Crosley (CDE/CDG series), Kenmore, White-Westinghouse, and Gibson dryers
Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
XP134719300
Part Type
Dryer Drum Drive Belt
Condition
Aftermarket Replacement
Application
Dryers (Frigidaire/Electrolux platform)
Length
90"
Width
5/16"
Thickness
1/8"
Ribs / Grooves
5 ribs / 4 grooves
Color
Black
Material
Rubber with reinforced fabric/cord
Installation Orientation
Grooves face DOWN against the drum
Often Paired With
Idler Pulley (134793500 or 134793511, sold separately)
Compatible Brands
Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, Gibson
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooves Face DOWN Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Remove the top and/or front panels of the dryer to access the drum — the specific procedure varies by model, but typically involves removing 2–4 screws under the top edge or lint trap area, then lifting or tilting the top panel forward. Once the top is off, disconnect the door switch wire harness and lift the front panel free. This exposes the drum, motor, and idler pulley. Photograph the belt routing before disassembly if any belt fragments remain — you'll need to match the routing pattern with the new belt. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley. Support the drum from underneath (a wooden block or two can help hold it in position). Route the new 134719300 belt around the drum in the same position as the old belt — approximately 4-6 inches from the front lip of the drum. Install with the grooves facing DOWN, against the drum surface — this is essential for proper engagement with the motor pulley. From under the drum, route the belt over the idler pulley and around the drive motor pulley in a Z-shape. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly. Verify the drum rotates freely without binding — if it doesn't, the belt is twisted, kinked, or misrouted; fix it before reassembling. Reinstall the front and top panels, reconnect the door switch, restore power, and run a test cycle to confirm normal operation. Tools needed: Phillips screwdriver, wooden block, side cutters (for removing broken belt fragments), flathead screwdriver, work gloves.
Frequently Asked Questions
My dryer runs but the drum won't turn — is the belt the problem?
Almost certainly, yes. When the motor runs (you hear the humming/whirring) but the drum stays still, the belt has almost always snapped or is slipping badly. To confirm without opening the dryer: reach in through the door and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum bearings or rollers could be the issue. In either case, opening the dryer to inspect the belt visually is the definitive check — a snapped belt will be lying in the bottom of the cabinet.
Why do I have to install the belt with grooves facing down?
The dryer's motor pulley is a smooth, un-grooved cylinder — the belt runs against it with the flat (smooth) side. The drum, on the other hand, needs the grooves to positively engage and drive without slipping under load. So the grooved side faces the drum (down when you're routing the belt around the drum from above), and the smooth side wraps around the motor pulley and idler pulley. Installing the belt backwards with grooves facing up will cause the belt to slip against the drum immediately and can burn out the new belt within a few minutes of operation.
Should I replace the idler pulley at the same time?
Yes, it's strongly recommended. The idler pulley (134793500 or 134793511 on many compatible dryers) maintains constant tension on the drum belt as the drum rotates. It wears from the same friction cycles as the belt — when the belt fails, the idler pulley bearings have typically also been stressed and are near end-of-life. Since the dryer is already open and the pulley is right there next to the belt, replacing both saves you a repeat repair when the pulley fails a few months later. Signs of a worn idler pulley: rough or noisy rotation when spun by hand, visible wear grooves, or seized bearings.
What's the difference between 134719300 and 137315300?
These are the same drive belt across production revisions. 137315300 was a Frigidaire OEM part number and 134719300 is the current cross-referenced part number that covers the same belt. Both are physically and functionally identical — if your dryer's parts diagram shows either number, this listing is the correct replacement. LB5300 and 7134719300 are additional catalog references for the same belt.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable rubber with reinforced fabric/cord to match the dimensions (90"L x 5/16"W x 1/8"H), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original 134719300 drum belt used in compatible Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine Whirlpool WPW10131172 Dryer Drive Belt - Compatible with Admiral, Amana, Maytag, Whirlpool
Product Description
Ensure efficient drying with the Genuine Whirlpool WPW10131172 Dryer Drive Belt. This OEM drive belt is designed for select Admiral, Amana, Crosley, Inglis, Maytag, and Whirlpool dryers, driving the drum to ensure proper rotation and consistent performance. Made of durable rubber, it delivers reliable tension and flexibility, addressing issues like the drum not spinning, excessive noise, or failure to start.
Note: Includes one drive belt. Disconnect power and gas (if applicable) before installation. Inspect drum rollers and idler pulley for wear during replacement.
Replaces part numbers: WPW10131172, W10131172, 1449763, PD00003839, EAP11748749, AP6015470, PS11748749.
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Admiral, Amana, Crosley, Inglis, Maytag, and Whirlpool dryers.
🔄 Specifications: OEM rubber drive belt, 4 ribs, 3 grooves.
💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability and proper tension.
🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 20–30 minutes.
🛡️ Effective Fixes: Resolves drum not spinning, excessive noise, or failure to start issues.
Product Specification
Part Number: Genuine Whirlpool WPW10131172
Component Type: Dryer drive belt
Material: Rubber
Mounting: Tension-mounted around drum and motor pulley
Operating Conditions: Suitable for household and commercial dryer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation.
Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today!
Add to cart now for a reliable fix!
WP40111201 Genuine OEM Whirlpool Dryer Drum Belt
The WP40111201 is a genuine Whirlpool OEM drum belt for full-size Whirlpool-built dryers. The belt is a long, slender loop that wraps all the way around the outside of the drum, passes around the tension (idler) pulley, and loops around the drive motor pulley. This belt is the sole mechanical connection between the motor and the drum — there is no gear or direct coupling — so when it breaks or slips off, the dryer behaves in a very specific way: the console lights up, the motor runs, the blower moves air, but the drum sits still. Open the door and spin the drum by hand and it will turn freely with no resistance.
This belt measures 93-3/8 inches long and 3/8 inch wide, with a 5-rib multi-groove profile. Belts fail from age and heat: the rubber hardens over years of thermal cycling, the ribs glaze over and begin slipping under a wet load, and eventually the belt cracks through or snaps outright. A screeching or squealing noise, a rhythmic thump timed to drum rotation, fraying at the edges, or black rubber dust in the cabinet are all signs a belt is near the end of its life. As a genuine OEM part, the WP40111201 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It directly replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, and R0606549.
Quick Answer
The WP40111201 Genuine OEM Whirlpool Dryer Drum Belt fixes full-size Whirlpool-built dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer screeches, squeals, or thumps during operation. 93-3/8" long, 3/8" wide, 5-rib profile. Replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, R0606549. Grooves face against the motor pulley on this platform — same orientation as our Y312959 belt.
Common Problems This Part Fixes
Dryer runs and hums but the drum does not turn — the classic broken belt symptom
Drum spins freely by hand with no resistance when the door is open
Loud screeching or squealing that begins as soon as the cycle starts
Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt
Grinding or rumbling from inside the cabinet as a frayed belt drags
Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping
Dryer won't start, or inadequate heating reported alongside a belt-related noise
Black rubber dust or belt fragments found in the bottom of the cabinet
Visible cracking, fraying, glazing, or stretching on the old belt
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, AWP47792, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115.
40111201 is the long-running legacy Whirlpool number and WP40111201 is the current part number carrying the "WP" prefix. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select full-size Whirlpool-built dryers across the Whirlpool family of brands, including:
Whirlpool electric and gas dryers
Maytag dryers (select Whirlpool-built models)
KitchenAid dryers (select models)
Amana dryers (select models)
JennAir dryers (select models)
Kenmore dryers (select Whirlpool-built models, including SDG3606AWW)
Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, and Norge dryers (select models)
This belt fits a large number of standard full-size front-load dryers used across North America. Because the compatible model list spans many years and revisions, always verify your full model number against your dryer's data label before ordering.
Note: Whirlpool and Maytag use more than one length of drum belt across their dryer lineups, and belts of a similar rib count and width are not automatically interchangeable. This belt is 93-3/8" long — it is NOT the same belt as our 100"-long Y312959 belt used on other Maytag/Whirlpool platforms. A belt that's too long or too short for your drum will slip, walk off the pulley, or fail to seat properly. Measure your old belt or verify your model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified length, rib profile, and tension
93-3/8" length, 3/8" width, 5-rib multi-groove design
Wraps around the drum, tension pulley, and drive motor pulley to transfer motor rotation to the drum
Resolves "motor runs but drum won't turn," "screeching," "squealing," and "drum spins freely by hand" symptoms
Multi-rib construction grips the motor pulley without slipping under heavy wet loads
Direct drop-in replacement — no cutting, splicing, or modification required
Replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, and R0606549
Compatible with Whirlpool, Maytag, KitchenAid, Amana, JennAir, Kenmore, Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, and Norge dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WP40111201
Part Type
Dryer Drum Drive Belt
Condition
Genuine OEM
Brand
Whirlpool
Length
93-3/8 in.
Width
3/8 in.
Ribs
5
Material
Reinforced rubber
Rib Orientation
Grooves face against the motor pulley
Routing
Around drum → tension pulley → drive motor pulley
Fuel Type
Electric and gas dryers
Quantity
1 belt
Compatible Brands
Whirlpool, Maytag, KitchenAid, Amana, JennAir, Kenmore, Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, Norge
Installation Notes
⚠️ Unplug Dryer Before Starting — Photograph Belt Routing First Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Pull off the lint trap and remove the screws securing the top panel, then raise the panel and support it with a block of wood. Remove the rear access panel to locate the motor, blower wheel, and belt. Photograph how the old belt routes around the drum, the tension pulley, and the motor pulley before removing anything — if the belt is already broken, note that the grooved side of this belt rides against the motor pulley, with the smooth back facing the drum. Loosen and remove the motor mount, lift the motor slightly, and slide the old belt free. The front panel typically needs to come off as well to fully access the drum. Vacuum out accumulated lint while the cabinet is open — lint buildup around the motor and idler is what cooks belts prematurely. Place the new belt around the drum, seat it in the polished wear track left by the old belt, then route it around the tension pulley and around the motor pulley. Useful trick: tape the belt loosely to the drum with a strip of masking tape before repositioning the motor, so it doesn't slide off while you work. Re-secure the motor mount, then rotate the drum by hand several full turns and confirm the belt tracks straight and stays centered without walking toward an edge. While you're in there, spin the tension pulley and each drum roller by hand — if any is noisy, gritty, or has play, replace it now, since a seized pulley or worn roller will destroy the new belt quickly. Reassemble the front and rear panels and the top panel, restore power, and run a short empty cycle listening for squeal or thump before loading it. Tools needed: Phillips screwdriver, 5/16" nut driver, flat-blade screwdriver, putty knife, masking tape, work gloves.
Frequently Asked Questions
How do I confirm the belt is broken and not the motor?
With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. A failed motor usually buzzes and does nothing, or trips the breaker outright.
What's the difference between WP40111201 and 40111201?
They are the same belt across production revisions. 40111201 was the long-running legacy Whirlpool number and WP40111201 is the current number carrying the "WP" prefix Whirlpool adopted. WP40111201VP is a variant packaging code for the same belt. If your dryer's parts diagram or the old belt itself shows any of these numbers, this listing is the correct replacement. The remaining cross-references (14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, R0606549) are catalog identifiers used by various parts distributors for the same belt.
Is this the same belt as your Y312959 listing?
No. This belt is 93-3/8" long, while the Y312959 belt in our catalog is 100" long — the two are used on different Maytag/Whirlpool dryer platforms and are not interchangeable. Both share a similar 5-rib profile and grooves-against-motor-pulley orientation, which is exactly why they're easy to confuse. Always check your model number or measure your old belt's length before ordering either one.
Which way do the grooves face on this belt?
On this Whirlpool platform, the grooved (ribbed) side of the belt rides against the motor pulley, with the smooth back of the belt facing the drum. This is the same orientation as our Y312959 belt, but it is the opposite of some other manufacturers' platforms — for example, Frigidaire's 134719300 belt runs with the grooves facing down against the drum instead. Always confirm orientation for your specific brand and platform, and photograph the old belt before removing it whenever possible.
The dryer squeals but the drum still turns. Belt or something else?
Could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry tension pulley bearing makes a very similar squeal, and worn drum rollers add a low rumble underneath. With the cabinet open, spin the tension pulley and each roller by hand — they should turn smoothly and silently. If they're gritty, noisy, or have play, replace them along with the belt, since they share the same teardown and you'd otherwise be opening the dryer twice.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original 93-3/8" length, 3/8" width, and 5-rib profile of the drum belt originally installed in your Whirlpool, Maytag, KitchenAid, Amana, or related dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE03X29897 Dryer Drum Belt
Product Title
XPARTCO WE03X29897 Dryer Drum Belt - Compatible with GE, Hotpoint, Kenmore Dryers
Product Description
Ensure your dryer tumbles smoothly with the XPARTCO WE03X29897 Dryer Drum Belt from Parts-O-Matic. This high-quality aftermarket belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum for efficient drying. Compatible with select GE, Hotpoint, RCA, and Kenmore dryers, this belt resolves issues like failure to tumble, squealing or thumping noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic!
Key Features:
✅ Broad Compatibility: Fits select GE, Hotpoint, RCA, and Kenmore dryer models.
🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying.
💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair.
🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production.
Compatibility:
Compatible with models including but not limited to:
GE: GTD33EASK0WW, GTD42EASJ2WW, GTD65EBSJ0WS, GTX33EASK0WW
Hotpoint: HTX21EASK0WW, HTX24EASK0WS
Kenmore: 363.61542412, 363.71542410
Replaces part numbers: WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE03X29897-30PK, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, PS16542496.
Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance.
Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension (e.g., WE12X83). Download our installation guide or watch our YouTube tutorial for step-by-step instructions.
Caution: Avoid stretching the belt during installation, as this can reduce its lifespan.
Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today!
Add to cart now for an affordable fix with free shipping on your entire order!
349241T Genuine OEM Dryer Drum Roller Kit - Compatible with Whirlpool, Kenmore, Maytag
Restore smooth and quiet operation to your dryer with the 349241T Genuine OEM Dryer Drum Roller Kit. This Whirlpool-manufactured kit includes two drum rollers, four tri-rings, and one retaining washer, designed to support the drum in select Whirlpool, Kenmore, Maytag, and other compatible dryers. It addresses issues like excessive noise, vibration, or drum not tumbling, ensuring efficient drying performance. Recommended to replace both rollers at once for optimal results.
This set includes 2 drum rollers, 4 tri-ring retaining clips, and 2 retaining washers — everything needed for a complete rear roller replacement. Each roller measures 3-1/4"L x 1"W x 3-1/4"H and is constructed from rubber over a metal bearing hub with a plastic axle support. Both rollers must always be replaced at the same time. The set directly replaces 349241, 349241TVP, 8170, 8205, 337089, 340352, 661562, 3389901, 3397588, 3397590, AP3098345, PS347627, and several additional cross-reference numbers. Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair. Installs in 30–60 minutes with basic hand tools.
Quick Answer
349241T Genuine OEM Dryer Drum Roller Kit. This Whirlpool-manufactured kit includes two drum rollers, four tri-rings, and one retaining washer, designed to support the drum in select Whirlpool, Kenmore, Maytag, and other compatible dryers. It addresses issues like excessive noise, vibration, or drum not tumbling, ensuring efficient drying performance. Recommended to replace both rollers at once for optimal results. Replaces 349241, 8170, 8205, 337089, 3389901, AP3098345, PS347627.
Common Problems This Part Fixes
Loud thumping, rumbling, or squealing noise during the drying cycle
Grinding or scraping sound when the drum is turning
Drum turning unevenly or wobbling during operation
Drum not spinning — rollers so worn they can no longer support the drum
Squealing or squeaking that gets worse over time as roller bearings degrade
Marks or scuff lines on clothes — drum dragging against the dryer cabinet
Excessive vibration during the drying cycle
Replaces Part Numbers
This drum roller set directly replaces the following OEM and cross-reference part numbers:
349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AWP39168, PD00002257, EAP347627, AP3098345, PS347627.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum roller set is compatible with select 29-inch gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric — 29" models)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers
KitchenAid dryers
Amana dryers
Roper dryers
Crosley dryers
Estate dryers
Inglis dryers
Admiral dryers
Magic Chef dryers
Note: The 349241T rollers are for 29-inch Whirlpool-family dryers. Newer Whirlpool Duet front-load dryers and larger-capacity models use different roller part numbers (such as WPW10314173 / 8536974). Always verify your model number before ordering.
Key Features
Set of 2 rear drum support rollers — supports and cradles the drum as it rotates for smooth, quiet operation
Includes all hardware: 2 rollers, 4 tri-ring retaining clips, 2 retaining washers — everything needed for a complete installation
Dimensions: 3-1/4"L x 1"W x 3-1/4"H per roller
Rubber wheel over metal bearing hub with plastic axle support — designed to resist wear and heat under continuous drum load
Both rollers must be replaced at the same time — replacing only one results in uneven drum support and accelerated wear on the new roller
Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair
Compatible with 11 major appliance brands on the Whirlpool 29-inch platform
Dryer Genuine OEM Part.
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
349241T
Part Type
Dryer Rear Drum Support Roller Set
Condition
Genuine Whirlpool OEM
Application
29-inch Gas and Electric Dryers
Quantity
Set of 2 rollers (replace both at the same time)
Roller Dimensions
3-1/4"L x 1"W x 3-1/4"H (per roller)
Material
Rubber wheel / Metal bearing hub / Plastic axle support
Color
Black / White
Kit Includes
2 drum rollers, 4 tri-ring retaining clips, 2 retaining washers
Often Replaced With
341241 Drum Belt, 691366 or 279640 Idler Pulley
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to access the drum. Release the drive belt from the idler pulley, lift the drum forward, and set it aside. The rear drum support rollers are mounted on shafts on the rear bulkhead — each roller is secured with a tri-ring clip and a retaining washer. Use needle-nose pliers to remove the old tri-ring clips, then slide the old rollers off the shafts. Install the new rollers, new retaining washers, and new tri-ring clips on the shafts. Reinstall the drum, re-route the belt around the motor and idler pulley, and reassemble the front and top panels. Restore power and run a test cycle to verify quiet, smooth drum operation. Tip: while the dryer is open, inspect and replace the drum belt (341241) and idler pulley (691366 or 279640) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife, needle-nose pliers.
Frequently Asked Questions
What do the drum support rollers do?
The rear drum support rollers are cylindrical wheels mounted on fixed shafts at the back of the dryer cabinet. As the drum rotates, its rear outer rim rests on these rollers, which carry the drum's weight and allow it to spin smoothly and quietly. When the rubber wheels wear down or the bearing hubs corrode, the drum no longer rides smoothly on the rollers — causing thumping, rumbling, or squealing noises that get progressively worse. In severe cases, worn rollers allow the drum to sag and drag against the cabinet rear panel.
Why must I replace both rollers at the same time?
Both rear drum support rollers carry the same load and experience the same wear through every drying cycle. When one roller fails, the other has been under the same stress for the same number of cycles and is almost certainly near the end of its useful life. Replacing only the failed roller leaves one worn roller supporting the drum unevenly, which puts extra stress on the new roller and causes it to wear out much faster. Replace both rollers at the same time to ensure even drum support and get the full service life from the new parts.
Should I also replace the belt and idler pulley at the same time?
Yes — this is the ideal time. Since the dryer must be fully disassembled to access the rear drum rollers, replacing the drum belt (341241) and idler pulley (691366 or 279640) at the same time is strongly recommended. All three parts wear at similar rates, and a worn belt or idler pulley is often what caused the rollers to wear prematurely. Doing all three in one repair eliminates the most common drum drive failure points and saves you from repeating the teardown in the near future. The 4392065 maintenance kit includes all three parts together.
What causes dryer drum rollers to wear out?
Drum rollers wear naturally over time from the continuous load of supporting the rotating drum. The most common accelerating factors are operating the dryer with a worn or broken belt (which allows the drum to sag and puts extra weight on the rollers), running very large or heavy loads frequently, and allowing lint to accumulate around the roller shafts, which causes the bearings to run dry and wear faster. Regular dryer maintenance — including cleaning lint from around the drum and periodically checking the belt — helps extend roller life.
Is this an OEM or aftermarket part?
It is a genuine Whirlpool OEM part.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
WH03X32217 Washer Genuine Motor Pulley
Fits select GE Washer models.
Replaces Part Numbers: WH03X32217, WH49X25377, WH07X24182, AP7018598, PS16554753.
Description: This Motor Pulley & Nut is an OEM part for select GE washing machine models. Common causes of a bad pulley and nut can include wear from repeated use over time damaging threads, cracks forming in plastic pulleys, or loose, stripped, or lost mounting fasteners compromising power transfer.
12238200001084 Genuine OEM Midea Dryer Bearing House Assembly (Drum Rear Bearing)
The 12238200001084 is a Genuine OEM Midea replacement bearing house assembly compatible with select Midea, Criterion, and Insignia electric and gas dryers, including the CDE41N1AW series. The bearing house assembly is mounted at the rear of the drum and houses the bearing that the rear drum shaft rotates within, supporting the back of the drum and allowing it to spin smoothly. Unlike front-mounted slide rollers used on some dryer platforms, this Midea design uses a rear bearing housing assembly to carry the load at the back of the drum.
When the bearing house assembly wears out — typically from age, lack of lubrication, or accumulated lint and debris — the drum no longer spins smoothly on its rear support, resulting in grinding, rumbling, or squealing noise, increased drum drag, and in advanced cases, visible wobble or binding of the drum during rotation. As a Genuine OEM part manufactured by Midea to factory specifications, the 12238200001084 is a complete bearing house assembly designed as a direct replacement for the original equipment component. Installs in 45–60 minutes with basic hand tools, as drum removal is required.
Quick Answer
The 12238200001084 Genuine OEM Midea Dryer Bearing House Assembly fixes Midea, Criterion, and Insignia dryers with grinding, rumbling, or squealing noise from the rear of the drum, increased drum drag, or visible drum wobble. Mounted at the rear of the drum — houses the bearing the rear drum shaft rotates within. Genuine OEM. Compatible with Midea CDE41N1AW and related Midea electric dryer platform models. Requires drum removal to access — a more involved repair than a front roller swap.
Common Problems This Part Fixes
Loud grinding or rumbling noise from the rear of the drum during the drying cycle
Squealing or squeaking noise as the drum rotates — worn or dry bearing surface
Increased drag or resistance felt when manually rotating the drum by hand
Drum wobbling or binding during rotation — worn bearing no longer providing stable support
Excessive vibration during the drying cycle
Visible wear, cracking, or lint/debris buildup in the bearing house area
Drum scraping against the rear bulkhead due to lost bearing support
Replaces Part Numbers
This bearing house assembly directly replaces the following part number:
12238200001084, AP7154967, PS18167713
This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This bearing house assembly is compatible with select Midea, Criterion, and Insignia dryers, including:
Midea CDE41N1AW electric dryer
Midea MLE series electric dryers (select models — same drum/bearing platform)
Criterion electric dryers built on the Midea platform (select models)
Insignia electric dryers built on the Midea platform (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
Complete bearing house assembly — supports the rear of the drum and allows smooth, quiet rotation
Houses the bearing that the rear drum shaft rotates within — a sealed-style design intended to resist lint intrusion
Direct replacement for the original equipment bearing house assembly
Compatible with Midea CDE41N1AW and related Midea, Criterion, and Insignia electric dryer platform models
Installs in 45–60 minutes with basic hand tools (drum removal required)
Product Specifications
Part Number
12238200001084
Part Type
Dryer Bearing House Assembly (Drum Rear Bearing)
Condition
Genuine OEM
Application
Electric Dryers (Midea platform)
Location
Rear of drum — houses rear drum shaft bearing
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum. Take a photo of the belt routing before disconnecting the drive belt from the idler pulley. Carefully lift the drum out of the cabinet and set it aside on a padded surface. Locate the bearing house assembly mounted at the rear bulkhead where the drum's rear shaft was seated. Remove the mounting screws or clips securing the old bearing house assembly and pull it free. Clean any accumulated lint or debris from the mounting area before installing the new part. Install the new 12238200001084 bearing house assembly in the same position and secure the mounting hardware. Reinstall the drum, re-route and reconnect the drive belt, and reassemble the front and top panels. Restore power and run a test cycle to confirm the drum rotates smoothly and quietly. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
What does the bearing house assembly do?
The bearing house assembly is mounted at the rear bulkhead of the dryer and houses the bearing that the rear drum shaft rotates within. It supports the back of the drum as it spins, allowing smooth, low-friction rotation throughout the drying cycle. Unlike dryer platforms that use front-mounted slide rollers or felt seals for drum support, this Midea design relies on a dedicated rear bearing housing to carry the structural load at the back of the drum. As the bearing wears, friction increases, leading to noise, drag, and eventually wobble or binding if left unaddressed.
How do I know if the bearing house assembly has failed versus another component?
A grinding, rumbling, or squealing noise specifically tied to drum rotation — rather than the blower motor or idler pulley — and noise that changes pitch as the drum speeds up or slows down often points to the rear bearing. With the dryer unplugged and the drum exposed (front panel removed), try rotating the drum by hand: if you feel noticeable resistance, grinding, or grittiness compared to a smooth, free rotation, the bearing house assembly has likely worn out and needs replacement.
Why does this repair require removing the drum?
The bearing house assembly is mounted at the rear bulkhead behind the drum, supporting the drum's rear shaft from the inside. There is no way to access this component without first removing the front panel and lifting the drum out of the cabinet. This makes it a more involved repair than swapping a front-accessible part like a belt or idler pulley, but it follows the same general dryer disassembly procedure used for accessing other internal drum components.
Should I inspect other components while the drum is out?
Yes — since the drum must already be removed to access the bearing house assembly, this is an excellent opportunity to inspect the drive belt, idler pulley, and any felt seals or gaskets around the drum opening for wear. Components in this drum drive system tend to wear together, and addressing multiple worn parts in a single repair session helps avoid a near-term repeat teardown.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same bearing house assembly installed in compatible Midea, Criterion, and Insignia electric dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 33002535 Dryer Drum Belt Replaces WP33002535
The XPARTCO 33002535 is an aftermarket replacement dryer drum belt compatible with a wide range of Maytag, Amana, Crosley, and Kenmore dryers. The drum belt is a long, ribbed rubber belt that wraps around the outside of the dryer drum and connects to the motor pulley and idler pulley, transferring the motor's rotation to spin the drum during every drying cycle. When the belt breaks or wears out, the motor continues to run but the drum stops spinning — clothes tumble only under gravity or not at all, and the dryer produces heat with no airflow through the load.
This belt measures 91-5/8" in length and 5/16" in width, with 5 ribs and 4 grooves — the correct profile to grip the drum, motor pulley, and idler pulley on compatible Maytag-platform dryers. Made from high-strength rubber designed to resist stretching, cracking, and heat degradation over years of use. It directly replaces WP33002535, 33001777, 63700300, 791135, WP33002535VP, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 33002535 Dryer Drum Belt fixes Maytag-platform dryers where the drum is not spinning, the motor runs but the drum is still, or the belt is visibly broken or worn. 91-5/8" long x 5/16" wide, 5 ribs, 4 grooves. Compatible with Maytag, Amana, Crosley, and Kenmore dryers. Replaces WP33002535, 33001777, 63700300, 791135, and more. Installs in 30–45 minutes.
Common Problems This Part Fixes
Dryer drum not spinning — motor runs but drum is completely still
Drum spinning only when manually pushed — belt is slipping or broken
Dryer running but not drying — drum not tumbling clothes through the airflow
Squealing or thumping noise just before the belt broke and the drum stopped
Belt visibly broken, frayed, or in pieces inside the dryer cabinet
Dryer tumbling unevenly or intermittently due to a stretched or slipping belt
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
WP33002535, 33002535, 33001777, 63700300, 6 3713880, 791135,AWP47236, EAP11741110, ER33002535, AP6007983, PD00002428, PS11741110.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select gas and electric dryers from the following brands:
Maytag dryers (gas and electric — MDE and MDG series)
Amana dryers (gas and electric)
Crosley dryers (gas and electric)
Kenmore / Sears dryers (select Maytag-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Wraps around the drum and connects to the motor pulley and idler pulley to transfer motor rotation to the drum
Length: 91-5/8 inches (91.5" / 2327 mm) — correct circumference for Maytag-platform dryers
Width: 5/16 inch — correct profile for the drum groove on compatible models
5 ribs, 4 grooves — ribbed profile grips the motor pulley and idler pulley without slipping
High-strength rubber construction — resists heat, stretching, cracking, and wear over years of daily use
Replaces WP33002535, 33001777, 63700300, 791135, and over 15 additional cross-reference numbers
Often replaced together with drum support rollers (12001541) and idler pulley (WP6-3700340)
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
33002535
OEM Part Number
WP33002535
Part Type
Dryer Drum Drive Belt
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Length
91-5/8 inches (91.5" / 2327 mm)
Width
5/16 inch
Ribs / Grooves
5 ribs, 4 grooves
Material
High-strength rubber
Color
Black
Often Replaced With
12001541 Drum Rollers, WP6-3700340 Idler Pulley
Compatible Brands
Maytag, Amana, Crosley, Kenmore
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel by unscrewing the screws inside the lint screen housing and releasing the front clips with a putty knife. Remove the front panel to access the drum. Release tension from the old belt at the idler pulley, then slide the belt off the drum, idler pulley, and motor pulley. Note how the belt is routed before removing it — take a photo if needed. Loop the new 33002535 belt around the drum with the ribbed side facing inward (toward the drum). Route the belt under the idler pulley and around the motor pulley, then pull the idler pulley toward you to create tension. Reassemble the front and top panels, restore power, and run a test cycle to confirm the drum spins. Tip: while the dryer is open, inspect the drum support rollers (12001541) and idler pulley (WP6-3700340) for wear and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife.
Frequently Asked Questions
What is the difference between 33002535 and WP33002535?
These are the same dryer drum belt. WP33002535 is the updated Whirlpool/Maytag OEM part number that superseded the original 33002535. The 33001777 is also a cross-reference for this same belt. This aftermarket replacement is compatible with all three numbers.
How do I know if my dryer belt has broken?
The clearest sign of a broken belt is a motor that runs — you can hear it humming — but the drum does not spin when you start the dryer. On most Maytag-platform dryers, you can open the dryer door and try to spin the drum by hand — if it spins very freely with almost no resistance, the belt has likely broken. You can also open the top or front panel to visually inspect the belt; a broken belt will be lying loose inside the cabinet or wrapped around components rather than stretched around the drum.
Should I replace the drum rollers and idler pulley at the same time?
Yes — since the dryer is already disassembled, this is the ideal time to inspect and replace the drum support rollers (12001541) and idler pulley (WP6-3700340). These components wear at similar rates to the belt, and a worn roller or pulley bearing is often what caused the belt to wear and break prematurely. Replacing all three together eliminates the most common sources of drum noise and prevents a second teardown in the near future.
Which side of the belt faces the drum?
The ribbed side of the 33002535 belt faces inward — toward the drum surface. The smooth side faces outward, away from the drum. When installing, wrap the belt around the drum with the ribs against the drum, then route the smooth side under the idler pulley and around the motor pulley. If the belt is installed inside-out, it will slip and the drum will not spin correctly.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag or Whirlpool OEM part, but is manufactured from high-strength rubber to match the length, width, and rib profile of the original WP33002535 drum belt.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
137292700 Genuine OEM Dryer Drum Belt
Product Title
137292700 Dryer Genuine OEM Drum Belt - Compatible with Frigidaire, Electrolux, Kenmore Dryers
Product Description
Keep your dryer running smoothly with the Genuine OEM 137292700 Dryer Drum Belt from Parts-O-Matic. This Genuine OEM belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum to ensure efficient tumbling and drying. Compatible with select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryers, this belt fixes issues like failure to tumble, unusual noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic!
Key Features:
✅ Broad Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryer models.
🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying.
💰 Cost-Effective Alternative: Genuine OEM part offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair.
🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production.
Compatibility:
Compatible with models including but not limited to:
Frigidaire: FEX831FS2, FEQ332ES0, FER231AS2, AGQ6000ES2
Electrolux: EIMED55IIW0, EIMED60JIW0
Kenmore: 417.91702001, 417.97812700, 417.97812702
Replaces part numbers: 137292700, 134163500, 134503900, 5303283287, AH3408299, EA3408299, AP4565702, PS3408299.
Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance.
Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension. Download our installation guide or watch our YouTube tutorial for step-by-step instructions.
Caution: Avoid stretching the belt during installation, as this can reduce its lifespan.
Shop Parts-O-Matic for Genuine OEM appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today!
Add to cart now for an affordable fix with free shipping on your entire order!
XPARTCO W10198086 Dryer Drum Belt Replaces WPW10198086
The XPARTCO W10198086 is an aftermarket replacement dryer drum belt for Whirlpool, Maytag, and Amana electric dryers. This belt wraps around the drum and the motor pulley, and it's what actually makes the drum turn — the motor drives the belt, and the belt tumbles the drum. When this belt breaks or wears out, the motor can still run, but nothing inside the dryer actually moves.
This is a 5-rib belt measuring approximately 92-1/2"L x 5/16"W x 1/8"H, with grooves on one side and a flat surface on the other. A broken or badly worn belt produces an unmistakable symptom: the dryer runs — you'll hear the motor and often the blower — but the drum doesn't turn at all, or turns only briefly before stopping. A simple way to confirm this diagnosis before opening the dryer is to try turning the drum by hand; if it spins freely with no resistance, the belt is almost certainly broken. Overloading the dryer with oversized loads is a common cause of belt failure over time. It directly replaces WPW10198086, W11575709, W11667279, LB8086, 1481904, AP6016842, AH2348726, EA2348726, PS2348726, EAP11750135, PS11750135, AWP49253, and PD00007598.
Quick Answer
The XPARTCO W10198086 Dryer Drum Belt fixes Whirlpool, Maytag, and Amana electric dryers where the motor runs but the drum doesn't turn, or turns only briefly. 5-rib belt, approximately 92-1/2"L x 5/16"W x 1/8"H. Replaces WPW10198086, W11575709, W11667279, LB8086, 1481904, AP6016842, AH2348726, EA2348726, PS2348726, EAP11750135, PS11750135, AWP49253, PD00007598. Try turning the drum by hand first — if it spins freely with no resistance, the belt has broken.
Common Problems This Part Fixes
Dryer runs — motor and blower audible — but the drum doesn't turn
Drum turns briefly then stops
Drum spins freely by hand with no resistance (indicating a broken belt)
Loud squeaking noise during operation from a worn but not yet broken belt
Burning rubber smell from a slipping or overheating belt
Dryer that stopped tumbling suddenly during a cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
WPW10198086, W10198086, 1481904, W11575709, W11667279, LB8086, PD00007598, EAP11750135, AP6016842, AWP49253, PS11750135
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select Whirlpool electric dryers, and also fits select Maytag and Amana dryers built on the same platform, including model numbers such as:
MEDC465HW0, MEDC215EW0, MEDC215EW1, MEDC200XW0, MEDC200XW1, MEDC200XW3
MEDX655DW0, MEDX655DW1, MEDX500BW0, MEDX500BW1
MEDC300BW0, MEDC300XW0, MEDC300XW1, MEDC400VW0, MEDC400BW1, MEDC415EW0
MGDC400VW0, MGDC215EW0, MGDC215EW2, MGDC465HW0, MGDC300XW3, MGDC400BW1, MGDC400BW2, MGDC500VW0, MGDC555DW1
MEDC555DW1, MEDC555DW2, MEDC100YQ0, MEDB766FW0
7MMGDC400DW0, 7MMGDC400DW1, 7MMGDC400DW2, 7MMEDC300DW1, 7MMEDC300BW0
Note: Always verify your full model number before ordering, since Whirlpool uses several different drum belts across its dryer lineup with different lengths and rib counts. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drum belt — connects the motor pulley to the drum so it can turn
Resolves "motor runs but drum won't turn," "drum stops mid-cycle," and "squeaking" symptoms caused by a worn or broken belt
5-rib design with grooves on one side, flat on the other
Approximately 92-1/2"L x 5/16"W x 1/8"H
Direct drop-in replacement matching the original belt routing
Replaces WPW10198086, W11575709, W11667279, LB8086, 1481904, AP6016842, AH2348726, EA2348726, PS2348726, EAP11750135, PS11750135, AWP49253, and PD00007598
Compatible with Whirlpool, Maytag, and Amana electric dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
W10198086
OEM Part Number
WPW10198086
Part Type
Dryer Drum Belt
Condition
Aftermarket Replacement
Length
Approx. 92-1/2 in.
Width
5/16 in.
Thickness
1/8 in.
Ribs
5
Color
Black
Material
Rubber
Repair Difficulty
Easy — 15 to 30 minutes
Quantity
1 drum belt
Compatible Brands
Whirlpool, Maytag, Amana
Installation Notes
⚠️ Unplug Dryer Before Starting — Check The Idler Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Lift the lint screen cover and remove the two screws underneath it — if your model has a lint screen with a built-in cover, simply pull it out and remove the screws. Run a putty knife around the top edge of the dryer to find the release clips, then press them in to release and swing the top open. Remove the front panel to access the drum and belt area; on many models, all the work for this repair is performed from the front rather than the rear. Route the new W10198086 belt around the drum with the grooved side against the drum, then loop it around the motor pulley and the idler pulley, following the routing diagram on the inside of the cabinet or your old belt's path if it's still intact when you remove it. If the belt broke rather than just wearing out, check that the idler pulley is still properly seated — a belt snapping can sometimes cause the pulley to pop out of position, and reseating it is a quick fix while you already have the panel open. Reinstall the front panel, close the top and secure the release clips, and reinstall the lint screen area and its screws. Restore power and run a test cycle to confirm the drum turns smoothly with no slipping or noise. Tools needed: Phillips screwdriver, 5/16" nut driver, putty knife, work gloves.
Frequently Asked Questions
My dryer runs but the drum won't turn. How do I confirm it's the belt before ordering?
Try turning the drum by hand with the dryer unplugged. If it spins freely with little to no resistance, that's a strong sign the belt has broken, since an intact belt normally provides some resistance from the motor and idler pulley connected to it. If the drum feels stuck or hard to turn instead, the problem may be elsewhere, such as a seized idler pulley or motor issue.
What caused my belt to break in the first place?
Belts wear out from age and normal use, but overloading the dryer with oversized or overly heavy loads is a common accelerating factor, since it puts extra strain on the belt with every rotation. Avoiding overloaded loads going forward can help the new belt last as long as it should.
While replacing the belt, I noticed the idler pulley looks out of place. Is that related?
Yes, this can happen when a belt breaks suddenly — the pulley can pop out of its normal seated position as tension is lost. Since you'll already have the panel open for the belt replacement, take a moment to check that the idler pulley is properly seated before closing everything back up, as this is a common and easy thing to overlook.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, width, rib count, and routing configuration of the original WPW10198086 drum belt used in compatible Whirlpool, Maytag, and Amana electric dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
12638000000786 Genuine OEM Midea Dryer Drum Roller
The 12638000000786 is a genuine Midea OEM dryer drum support roller. This roller sits underneath the drum, along its support track, and does the physical work of holding the drum's weight while letting it turn freely as the belt drives it around. A dryer typically uses more than one of these rollers working together to keep the drum properly supported and centered.
Over time, the wheel and bearing inside the roller wear down from the constant heat and rotation the dryer subjects them to, eventually developing a flat spot, seizing up, or simply wearing thin enough that the drum sits unevenly. A worn roller produces a distinctive symptom: a rumbling, squeaking, or thumping noise that rises and falls with drum rotation, often getting louder as a load tumbles or as the roller continues to wear.
Quick Answer
The 12638000000786 Genuine OEM Midea Dryer Drum Roller fixes Midea-built dryers with a rumbling, squeaking, or thumping noise that rises and falls with drum rotation. Supports and centers the drum along its support track.
Common Problems This Part Fixes
Rumbling or grinding noise that rises and falls with drum rotation
Squeaking or squealing noise from inside the dryer during operation
Thumping or knocking noise, especially with a heavier load
Noise that gets louder over time as the roller wears further
Drum that sits unevenly or wobbles slightly when turned by hand
Visible flat spot, cracking, or wear on the roller wheel
Noise that continues even with an empty drum tumbling
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
12638000000786, AP7155087, PS18170572
We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. This is a distinct part number from our 12638000004021 drum roller listing — the two are not interchangeable and do not cross-reference each other. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This drum roller is compatible with select Midea-built dryers.
Note: A specific verified compatible model list was not available at the time this page was built. Midea uses several different roller designs across its dryer lineup, and this part number is distinct from our 12638000004021 listing. Always verify your full model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase.
Key Features
Genuine Midea OEM part — factory-specified wheel and bearing design
Supports the drum along its support track, allowing smooth rotation as the belt drives it
Resolves "rumbling," "squeaking," and "thumping" noise symptoms caused by roller wear
Direct drop-in replacement for the original roller and axle assembly
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
12638000000786
Part Type
Dryer Drum Support Roller
Condition
Genuine OEM
Brand
Midea
Location
Drum support track
Function
Supports and centers the drum during rotation
Quantity
1 roller
Compatible Brand
Midea
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Access is typically through the rear panel: remove the screws securing the panel, then release the drum belt from the idler pulley to relieve tension so the drum can be supported and moved slightly for access to the rollers underneath. Photograph the roller and axle positions before removing anything. Remove the retaining clip or fastener holding the worn roller's axle in place, then slide the old roller off. Install the new 12638000000786 roller onto the axle in the same orientation, and secure it with the retaining clip or fastener. While you're in there, check the other rollers by spinning each one by hand — if any feel stiff, gritty, or worn, replace them at the same time, since they're typically the same age and wear on a similar schedule. Re-tension the belt around the idler pulley, reassemble the rear panel, restore power, and run a short empty cycle to confirm the noise has resolved. Tools needed: Phillips screwdriver, nut driver, pliers, work gloves.
Frequently Asked Questions
My dryer makes a rumbling noise that gets louder over time. Is this the part I need?
Yes, this is the classic symptom of a worn drum roller. As the wheel and bearing wear down, the noise typically starts subtle and gradually worsens, often becoming most noticeable with a full load as the extra weight puts more load on the worn wheel. If the noise rises and falls in rhythm with the drum turning, a roller is the most likely cause.
Is this the same roller as your 12638000004021 listing?
No. These are two distinct Midea part numbers, and they do not cross-reference or replace each other. If you're not sure which roller your dryer uses, check the number stamped on your existing roller or contact our support team with your model number, and we'll confirm which one is correct before you order.
Should I replace just one roller, or all of them?
It's worth checking all of them while you have access. Dryers typically use more than one roller supporting the drum, and since they're the same age and under the same stress, if one has worn out the others are often not far behind. Spin each roller by hand — if any feel stiff, gritty, or rough, replace them together to avoid repeating this repair again soon.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Midea to factory specifications — guaranteed fit, materials, and performance. It matches the original wheel design, bearing, and axle fitment of the drum roller originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
