Search results for "washer board"

W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly The W11670519 is a genuine Whirlpool OEM lid lock latch assembly for Maytag top-load washers on the Cabrio-style MVW platform. Unlike a simple mechanical lid switch, this is a true electronic lid lock: a 3-wire connector feeds the assembly, which both senses whether the lid is closed and physically locks it shut once a cycle with spin is underway. The control won't allow the washer to spin — and on many cycles won't even let it start — until this assembly confirms the lid is closed and locked, which is why a failing latch produces such a wide range of symptoms: a washer that won't start, a lid that won't lock or won't release, cycles that stall or interrupt partway through, or a washer that fills and agitates but refuses to spin. Built from high-strength, wear-resistant ABS and PP plastic with a precision locking mechanism, this assembly is designed to prevent the lid from popping open mid-spin, which protects against water leakage and the safety hazard of an open lid on a spinning basket. Common failure modes include a locking mechanism that has worn out and can no longer engage or release reliably, a broken internal switch that stops signaling lid status to the control board, and simple wear from years of daily cycling. It directly replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992. As a genuine OEM part, the W11670519 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly fixes Maytag top-load washers on the Cabrio-style MVW platform where the washer won't start, the lid won't lock or won't release, the washer fills and agitates but won't spin, the cycle stalls or interrupts, or the lid clicks repeatedly without locking. 3-wire electronic lid lock, ABS/PP construction. Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, EAP17215992. This is a locking latch assembly, not a simple lid switch — it's a different design from the direct-drive and GE-platform lid switches elsewhere in our catalog. Common Problems This Part Fixes Washer won't start even though the lid is closed Lid won't lock, or locks but won't release when the cycle ends Washer fills and agitates normally but won't spin Persistent clicking sound from the lid area without the lid actually locking Cycle stalling or interrupting partway through Lid feels loose or doesn't seat and lock the way it used to Error code related to the lid lock displayed on the control panel Water leakage risk from a lid that isn't sealing and locking properly during spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid lock latch assembly directly replaces the following OEM and cross-reference part numbers: W11670519, W11368616, AP7214714, AWP46151, PD00085482, 4981394, PS17215992, EAP17215992 W11368616 was an earlier number for this same assembly. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock latch assembly is compatible with select Maytag top-load washers on the Cabrio-style MVW platform, including model numbers such as: MVW4505MW0, MVW4505MW1, MVW4505MW2 MVW5035MW1, MVW5035MW2 MVW5430MW1, MVW5430MW2, MVW5430PBK0, MVW5430PBK1 MVW5435PBK0, MVW5435PBK1, MVW5435PW0, MVW5435PW1 Note: This is an electronic locking latch assembly for the Maytag Cabrio-style MVW platform, and it is a different design from the simpler lid switches used on other Whirlpool platforms — including our 8318084 (direct-drive top-load), 3355806 (Whirlpool thin-twin), WH12X955 (GE combo/spacemaker), and WH01X29528 (GE front-load door lock) listings. None of those are interchangeable with this assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which lid lock or switch your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism and switch design Electronic lid lock — both senses lid position and physically locks the lid during spin cycles Resolves "won't start," "lid won't lock or release," "fills but won't spin," and "cycle interruptions" symptoms caused by latch failure 3-wire connector for a direct plug-and-play electrical connection Constructed from high-strength ABS and PP plastic for wear and aging resistance Precision-designed locking mechanism helps prevent accidental lid opening during spin Direct drop-in replacement — no modification required Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11670519 Part Type Washer Lid Lock Latch Assembly Condition Genuine OEM Brand Whirlpool / Maytag Application Maytag Cabrio-Style Top-Load Washers (MVW Platform) Electrical Connection 3-wire connector Material High-strength ABS and PP plastic Function Senses lid closure and physically locks the lid during spin Supersedes W11368616 Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag Installation Notes ⚠️ Unplug Washer Before Starting — If The Lid Is Locked Shut, Release It Manually First Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. If the old latch has failed in the locked position and you can't open the lid, insert a small flathead screwdriver into the latch opening where the lock mechanism engages through the lid, and gently slide the mechanism back to release it — then prop the lid open so it can't re-close and re-lock while you work. Remove the two screws holding the top section (control panel, lid, and wash basket opening) and slide the top of the unit forward and up to remove it, then prop it securely (a sturdy support between the cabinet frame and the top panel works well) rather than relying on your hands to hold it up. With the top propped open, remove the plastic cowl that the lid latch sits inside, which also retains the lock mechanism. Unclip the wiring harness from the retaining clips running around the inside of the lid and let the assembly hang free. Photograph the wiring connections before disconnecting the 3-wire connector from the old assembly. At the back of the lid, two metal spring clips retain the mechanism — squeeze these with your fingers or a set of pliers to release the old assembly, then pop the new W11670519 into place the same way. Reconnect the 3-wire connector, reclip the wiring harness into its retaining clips, and reinstall the plastic cowl. Lower the top panel back into position, reinstall its retaining screws, and confirm the lid closes, latches, and locks correctly through a full test cycle including spin. Tools needed: small flathead screwdriver, Phillips screwdriver, pliers, a sturdy prop for the top panel, work gloves. Frequently Asked Questions My washer fills and agitates but won't spin. Is this the lid lock? Yes, this is one of the most common symptoms of a failing lid lock latch on this platform. The control requires confirmation that the lid is closed and locked before it will allow the higher-speed, higher-torque spin cycle to run, even if it's willing to run the gentler fill and agitate steps without full confirmation. If your washer gets partway through a cycle and simply refuses to spin, this assembly is a strong suspect. The lid keeps clicking but never actually locks. What does that mean? A repeated clicking sound without the lid actually locking usually points to a worn or failing internal locking mechanism inside this assembly — it's attempting to engage but can't complete the lock reliably. This is a textbook symptom that this part has worn out and needs replacement. My washer's lid is locked shut and won't open. How do I even get it open to do this repair? With the washer unplugged, you can usually manually release the lock: insert a small flathead screwdriver into the latch opening where the mechanism engages through the lid, and gently slide it back to disengage the lock. Once the lid is open, prop it so it can't fall shut and re-lock while you continue the repair. Is this the same part as the lid switches used on other Whirlpool washers? No. This is an electronic locking latch assembly specific to the Maytag Cabrio-style MVW platform, and it works differently from the simpler mechanical lid switches used on other Whirlpool-family platforms, including the direct-drive top-load switch, the Whirlpool thin-twin switch, and various GE-platform switches we also carry. These parts are not interchangeable with each other — always match the assembly to your specific washer platform. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-wire electrical connection, locking mechanism, and ABS/PP construction as the lid lock latch assembly originally installed in your Maytag Cabrio-style washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688995 (OE) Washer Water Inlet Valve (Cold) The XPARTCO W11688995 (OE — Original Equipment specification) is an aftermarket replacement cold water inlet valve built to OEM specifications, designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 (OE) Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Aftermarket Original Equipment (OE) — built to OEM specs. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket Original Equipment (OE) replacement — built to OEM specifications for direct fit and performance Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number W11688995 Designation OE (Original Equipment specification) Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. What does "OE" mean and how is this different from an OEM Whirlpool part? "OE" stands for Original Equipment — meaning this is an aftermarket replacement part manufactured to original equipment specifications. It is engineered as a direct-fit substitute matching the dimensions, electrical specifications, and function of the original Whirlpool W11688995. It is not a genuine Whirlpool-branded OEM part, but is built to the same quality standards and performs identically when installed in compatible washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WL49X20360 Washer Motor Speed Sensor Kit – Compatible with GE & Hotpoint Washers Product Description Restore accurate motor speed detection and reliable washer operation with the XPARTCO WL49X20360 Washer Motor Speed Sensor Kit. This high-quality aftermarket replacement kit monitors the washer motor’s rotation speed and sends feedback to the control board for proper agitation and spin performance. A faulty speed sensor can cause error codes, no spin, irregular agitation, or cycle interruptions. Replacing it with this XPARTCO kit helps restore smooth operation and consistent wash cycles. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WL49X20360, WH12X10515, 3031241, PD00025952, EAP8768455, AP5803767, PS8768455. Compatibility This replacement washer motor speed sensor kit fits select GE and Hotpoint washers. Example compatible models include (but are not limited to): GE GTW465ASNWW, GTW485ASJWS Hotpoint HTW240ASKWS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM fit and signal performance ⚙️ Accurate Motor Speed Feedback – Ensures proper agitation and spin control 🛠️ Direct-Fit Design – No modifications required 💪 Durable Electronic Components – Built for long-term reliability 💰 Cost-Effective Repair – Reliable alternative to OEM sensor kits 📐 Product Specification Part Number: XPWL49X20360 Component Type: Washer Motor Speed Sensor Kit Function: Motor rotation and speed detection Application: Washer drive motor feedback system Includes: Speed sensor and mounting hardware (as applicable) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the motor area from the bottom or rear of the washer. Locate and disconnect the old motor speed sensor. Remove mounting hardware and replace with the new XPARTCO WL49X20360 sensor. Reconnect wiring and secure the sensor. Reassemble panels, restore power, and run a test cycle. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore accurate washer motor control and dependable performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO W11688994 Washer Water Inlet Valve (Hot) The XPARTCO W11688994 is an aftermarket replacement hot water inlet valve compatible with select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The hot water inlet valve is mounted at the back of the washer where the hot water supply hose connects. When the washer's control board calls for hot water during a wash cycle, the valve's internal solenoid opens, letting hot water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with hot water at all, fill very slowly with hot water, fail to deliver hot or warm wash temperatures (even when selected), continuously drip water into the tub even when off, or display fill-related error codes. Construction is red and white plastic with a metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688994, W11036928, W11316255, W11486360, and AP7218602. Often replaced as a pair with the cold water inlet valve (W11688995, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688994 Washer Water Inlet Valve (Hot) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers that aren't filling with hot water, fill slowly with hot water, can't reach hot or warm wash temperatures, or have continuous water dripping into the tub when off. Red/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036928, W11316255, W11486360, AP7218602. Often paired with the cold water valve (W11688995, sold separately). Common Problems This Part Fixes Washer not filling with hot water — valve solenoid not opening when commanded Washer filling slowly with hot water — valve partially clogged or weak solenoid No hot or warm water in selected wash temperatures — only cold water flowing in Hot wash cycle running cool — hot valve not delivering normal flow Water continuously dripping into the tub when the washer is off — hot valve stuck open or not fully closing Water leaks at the hot valve body — internal seal failure Wash cycles taking much longer than normal due to slow hot fill Fill-related error codes when hot fill is required by the selected cycle Replaces Part Numbers This hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688994, W11316255, W11036928, W11486360, 4983330, AP7218602, AWP46795, EAP17216729, FIX17216729, OEM21655815, PD00085626, PS17216729.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — 7MWFC9822HC1, 8TWFC6810LW0, WFC682CLW0, WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0-HC3, MHW5630HW0-HW3, MHW6630HC0-HC3, MHW6630HW0-HW3, MHW8630HC0-HC4, MHW8630HW0-HW4 series Amana front-load washers — NFW5800HW0, NFW5800HW1, NFW5800HW2, NFW5800HW3, NFW5800HW4 and related models Inglis front-load washers — IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the hot water inlet valve (typically red). The matching cold water inlet valve is part number W11688995 (typically blue). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of hot water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for hot water and closes the moment the call is dropped 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Red and white plastic body with metal solenoid coil — heat-resistant construction designed for hot water cycle pressure and temperature Replaces W11036928, W11316255, W11486360, AP7218602, and PD00085626 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the cold water inlet valve (W11688995, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688994 Part Type Washer Water Inlet Valve (Hot) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Hot (paired cold valve is W11688995) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Red / White Material Plastic / Metal (heat-resistant) Often Paired With Cold Water Inlet Valve (W11688995, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Important: if the washer has just been running a hot cycle, allow the hot supply hose and valve to cool before handling — hot water can scald. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the hot valve is typically red. Disconnect the hot water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688994 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the hot supply hose at the wall, restore water and power, and run a test cycle on a hot or warm setting to confirm normal hot water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the cold water valve (W11688995) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions My washer isn't filling with hot water — is the hot valve the problem? Likely, yes — that's the most common symptom of a failed hot water inlet valve. Before replacing, do a few quick checks: 1) confirm the hot water supply at the wall is turned on and your home actually has hot water at that connection (test the faucet nearby); 2) check the supply hose for kinks or pinches; 3) inspect the inlet screen on the back of the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean, but the washer still won't get hot water, the W11688994 valve solenoid has likely failed and replacing it will resolve the issue. My washer fills but my hot wash isn't actually hot — could it still be this valve? Yes — when the hot inlet valve is partially failed (opening but not fully, or opening only briefly), the washer may complete its fill cycle by drawing extra cold water to compensate, but the resulting mix is much cooler than the selected wash temperature should be. If you've confirmed your home's hot water is hot, the supply hose is good, and you're still ending up with lukewarm "hot" washes, the hot valve is a likely cause. Replacing it restores proper hot water delivery and accurate wash temperatures. Should I replace the cold water valve at the same time? Yes, it's strongly recommended. The hot and cold inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching cold water valve is part number W11688995 (blue, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — could the hot valve be the cause? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the cold water supply at the wall and check if dripping continues. If it stops, the cold valve is at fault; if it continues, this hot valve is the cause. Replacing the W11688994 will resolve a leaking hot valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688994 hot water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO AJU75152601 Washer Water Inlet Valve Replaces 5221EA1008F, AJU73213301 The XPARTCO AJU75152601 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the WT1, WT4, WT5, WT6, and WT7 series. This is a multi-port valve assembly that controls water flow from the household supply lines into the washer tub and dispenser compartments. The assembly contains multiple solenoid-operated valve ports: hot water inlet, cold water inlet, bleach dispenser valve, fabric softener dispenser valve, and jet spray valve — all integrated into a single assembly that connects to the washer's control board via wiring harnesses. When the water inlet valve fails — or when one individual port fails — the washer may not fill at all, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or leak from the valve body. The valve solenoids operate at 12V DC. This kit includes the complete valve assembly and two AGM73269501 inlet screens. It directly replaces AJU73213301, 5221EA1008F, 5221EA1008P, AGF76283896, AP6308239, TAW35618287, AH3527446, AJU75152603, EA3527446, PS3527446, and PS12374721. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO AJU75152601 Washer Water Inlet Valve fixes LG and Kenmore top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or leak from the valve. Multi-port assembly with hot, cold, bleach, fabric softener, and jet spray valves. 12V DC solenoids. Includes 2 AGM73269501 inlet screens. Compatible with LG WT1xxx–WT7xxx and Kenmore 796-series. Replaces AJU73213301, 5221EA1008F, 5221EA1008P, AP6308239, TAW35618287, PS12374721. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more valve ports partially blocked or failing Washer filling with only hot or only cold water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach dispenser not dispensing during the wash cycle Fabric softener not dispensing at the correct rinse cycle point Jet spray not activating during fill Water dripping into the tub between cycles — valve port not closing completely Water leaking from the valve body or connection points at the back of the washer Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221EA1008F, AJU73213301, AJU75152601, AH3527446, AJU75152603, EA3527446, PS3527446, ALG53778, AP6308239, PD00042814, PS12374721, TAW35618287. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG and Kenmore top-load washers from the following series: LG top-load washers — WT1 series (WT1101CW, WT1201CW, WT1201CV, WT1301CW, WT1501CW, WT1701CW, WT1701CV, WT1801HVA, WT1801HWA and related models) LG top-load washers — WT4 series (WT4801CW, WT4870CW, WT4970CW and related models) LG top-load washers — WT5 series (WT5001CW, WT5070CW, WT5101HV, WT5101HW, WT5170HV, WT5270CW, WT5480CW, WT5680HVA, WT5680HWA and related models) LG top-load washers — WT6 series (select models) LG top-load washers — WT7 series (WT7200CW, WT7200CV, WT7500CW, WT7600HKA and related models) Kenmore / Sears top-load washers — 796-series (79631512210, 79631512211, 79631522211, 79631502210, 79631502211 and related models) Note: Always verify your exact model number before ordering. Newer LG WT7100/WT7150/WT7400/WT7405 series models use the AJU75152602 valve instead. Contact our support team with your model number to confirm the correct valve for your washer. Key Features Multi-port valve assembly — controls hot water, cold water, bleach dispenser, fabric softener dispenser, and jet spray from a single replaceable assembly 12V DC solenoid operation — responds to signals from the washer's control board to deliver the correct water to each compartment Resolves fill, dispenser, overfill, and drip-when-off symptoms in a single replacement Kit includes complete valve assembly and 2x AGM73269501 replacement inlet screens ABS plastic and stainless steel construction — durable and resistant to mineral buildup Replaces AJU73213301, 5221EA1008F, 5221EA1008P, AP6308239, TAW35618287, and over 10 additional cross-reference numbers Compatible with LG WT1xxx through WT7xxx and Kenmore 796-series top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number AJU75152601 Also Replaces AJU73213301, 5221EA1008F (current supersession) Part Type Washer Water Inlet Valve Assembly (Multi-Port) Condition Aftermarket Replacement Application LG and Kenmore Top-Load Washers Valve Ports Hot water, cold water, bleach dispenser, fabric softener dispenser, jet spray Solenoid Voltage 12V DC Material ABS plastic / Stainless steel Kit Includes Valve assembly + 2x AGM73269501 inlet screens Compatible Series LG WT1xxx, WT4xxx, WT5xxx, WT6xxx, WT7xxx; Kenmore 796-series Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve assembly is mounted on the upper rear of the washer — the external supply hoses connect to the hot and cold inlet ports. Photograph all wire harness connections and hose routing before disconnecting anything. Before installing, install the new inlet screens (AGM73269501) included in the kit into the hot and cold inlet ports of the new valve. Disconnect the old valve's external supply hoses, internal hoses, and wire harness connectors. Unscrew the mounting screws and remove the old valve. Install the new AJU75152601 valve, reconnect all hoses and wire harnesses in the same positions as documented in your photos, and secure the mounting screws. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify proper filling, confirm all dispenser ports activate at the correct cycle points, and check for leaks. Tools needed: Phillips screwdriver, pliers. Frequently Asked Questions What is the difference between AJU75152601, AJU73213301, and 5221EA1008F? These are all part numbers for the same LG washer water inlet valve assembly used across different production runs. 5221EA1008F was the original part number, AJU73213301 was an updated version, and AJU75152601 is the current part number. All three are interchangeable. If your washer's documentation, parts diagram, or old valve label shows any of these numbers, this replacement is the correct current part to order. My washer won't dispense fabric softener — is this the right part? Yes — the fabric softener dispenser solenoid is one of the ports integrated into the AJU75152601 valve assembly. When the fabric softener dispenser fails to activate at the right point in the rinse cycle, it is almost always because the solenoid valve controlling that port has failed. Since it is part of the same multi-port valve assembly, replacing the AJU75152601 resolves fabric softener, bleach, and jet spray dispenser issues in the same repair. Individual ports cannot be replaced — the complete assembly must be replaced when any one port fails. What are the AGM73269501 inlet screens included in the kit? The AGM73269501 screens are small mesh filters that install inside the hot and cold water inlet ports of the valve. They trap mineral deposits and debris from the household water supply before they can reach the valve seats and solenoid mechanisms. The kit includes two screens — one for the hot inlet and one for the cold inlet. Installing these fresh screens with the new valve helps extend valve life, especially in areas with hard water. If the old valve failed due to mineral clogging rather than solenoid failure, cleaning the supply hoses before installation is also recommended. How do I know if the water inlet valve has failed vs. the control board? You can test the valve solenoids with a multimeter. Disconnect the harness from a solenoid coil and probe both terminals — a working solenoid coil shows a resistance reading (typically 200–500 ohms); an open circuit confirms the solenoid has failed. If all solenoid coils test good but the valve still does not operate, the control board may not be sending the correct 12V DC signal to the solenoids — this requires checking voltage at the solenoid connectors with the washer powered and in a fill cycle, which is a more advanced diagnostic step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration, solenoid specifications, and dimensions of the original AJU75152601 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304511335 Washer Water Level Pressure Switch – Compatible with Frigidaire & Electrolux Washers Product Description Restore accurate water level control and proper washer operation with the XPARTCO 5304511335 Washer Water Level Pressure Switch. It is responsible for detecting the water level inside the washer tub and ensuring accurate water level control during the wash cycle. It detects the pressure changes caused by the water level, allowing the washer to adjust the water intake accordingly. A faulty pressure switch can cause overfilling, under-filling, or cycles not advancing properly. Replacing it with this reliable XPARTCO component helps ensure correct water levels and consistent wash performance. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers 5304511335, 4584277, EAP12176459, AFR17584, OEM18784872, PD00046588, AP6261621, PS12176459. Compatibility This replacement washer water level pressure switch fits select Frigidaire, Electrolux, Gibson, Crosley, and Kenmore (Frigidaire-manufactured) washers. Common compatible models include (but are not limited to): Frigidaire FFTW4120SW1, FFTW4120SW0, FFTW4120SW, FFTW4120SW0 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pressure sensing performance 💧 Accurate Water Level Detection – Ensures proper fill and cycle control ⚙️ Fixes Common Issues – Resolves overfill, underfill, and cycle errors 🧩 Direct-Fit Design – Installs easily with existing hose and wiring 💰 Cost-Effective Repair – Affordable alternative to OEM pressure switches ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: 💧 Washer overfilling or underfilling ⚠️ Incorrect water levels during cycles 🔄 Cycle not advancing properly 🛑 Washer stops mid-cycle 🚫 No water or continuous filling Replacing this pressure switch can restore proper water level control and washer performance. 📐 Product Specification Part Number: 5304511335 Component Type: Washer Water Level Pressure Switch Function: Detects water level and signals control board Connection Type: Air hose + electrical connector Application: Washer water level sensing system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the control panel or top panel. Locate the pressure switch and disconnect the air hose and wiring. Remove mounting screws and remove the old switch. Install the new XPARTCO 5304511335 pressure switch. Reconnect hose and wiring, reassemble, and restore power. Run a test cycle to verify correct water levels. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore accurate water level control and reliable washer performance — Add to Cart Now for a dependable repair!

Read more less

W10775188 Washer Genuine OEM Washplate Replaces Part Numbers: W10775188, 4282681, W10698538, W10834891, AP5959417, PS11699797. W10775188 Washer Washplate – Genuine OEM Part Restore optimal cleaning power with the W10775188 Washer Washplate. This Genuine OEM part replaces a worn or damaged washplate to ensure efficient agitation and even cleaning performance. Key Features: ✅ Genuine OEM Part – built to factory specs 🔁 Replaces: 4282681, W10698538, W10834891, AP5959417, PS11699797 🌀 Provides powerful agitation for deep cleaning 🛠️ Fits select Whirlpool, Maytag, and Amana top-load washers 🧰 Easy to install – includes center bolt ⚠️ Always unplug your washer before servicing. Need help with compatibility? Contact us! 📦 Part Number: W10775188

Read more less

WH23X29538 (OE) Washer Water Valve The WH23X29538 is an OE (Original Equipment) water inlet valve for GE front-load washers. This valve regulates the flow of water into the wash tub from the household supply line, with two water inlets (each with its own filter), four solenoid coils, and five water outlets working together to precisely control flow, temperature blending, and fill level throughout the cycle. Rated 120V, 60Hz. Built with a stainless steel-reinforced, high-quality ABS plastic body for corrosion resistance and long-term sealing. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a range of symptoms: leaking or overflowing water, slow or irregular water filling, the washer filling non-stop or not filling at all, incorrect water temperature, or unusual noise during the fill cycle. It directly replaces WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225. Quick Answer The WH23X29538 (OE) Washer Water Valve fixes GE front-load washers with water leaking or overflowing, slow or irregular filling, non-stop filling, no water filling at all, incorrect water temperature, or unusual fill-cycle noise. 120V, 60Hz, 2 inlets with filters, 4 solenoid coils, 5 outlets. Replaces WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225. This valve is specific to the GFW550 series — it is a separate part from our WH23X29553 listing, which fits the GFW650/850 and PFW870/950 series. Common Problems This Part Fixes Water leaking or overflowing from the valve area Slow or irregular water filling Washer filling non-stop and not shutting off Washer not filling with water at all Incorrect water temperature during fill Unusual noise during the water fill cycle Error code related to water fill or temperature What Is an OE Part? OE (Original Equipment) means this part is manufactured by the same original supplier that produces the Genuine OEM version — identical fit, materials, and performance. The only difference is packaging: OE parts ship under our XPARTCO brand rather than the appliance manufacturer's branded box, which is why they can't be listed as Genuine OEM. You get factory-original quality at a more affordable price. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE front-load washers, including model numbers such as: GFW550SPN0DG, GFW550SPN1DG, GFW550SPN2DG, GFW550SPN3DG GFW550SPR0RS, GFW550SPR3RS, GFW550SPR4RS, GFW550SPR5RS GFW550SSN0WW, GFW550SSN1WW, GFW550SSN2WW, GFW550SSN3WW, GFW550SSN4WW, GFW550SSN5WW Note — not the same as WH23X29553: This valve is specific to the GFW550 series. It is a separate part from our WH23X29553 listing, which fits the GFW650/850 and PFW870/950 series and has a completely different cross-reference set. The two are easy to confuse given the similar numbering — always confirm your exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features OE (Original Equipment) water inlet valve — manufactured by the same supplier as the Genuine OEM version Two water inlets with filters, four solenoid coils, five water outlets for precise fill control Resolves "leaking/overflowing," "slow or irregular fill," "non-stop filling," "won't fill," and "wrong temperature" symptoms ABS plastic body with stainless steel reinforcement for corrosion resistance Rated 120V, 60Hz Direct drop-in replacement — matches the original mounting and hose connections Replaces WH23X29538, C-163/21-A13, 33090201, PD00071094, EAP16217225, AP6990115, AGE26158, PS16217225 Compatible with GE front-load washers in the GFW550 series Product Specifications Part Number WH23X29538-OE Designation OE (Original Equipment) Part Type Washer Water Inlet Valve Brand GE Application Front-Load Washers (GFW550 Series) Voltage 120V Frequency 60 Hz Inlets 2, each with a filter Outlets 5 Solenoid Coils 4 Body Material ABS plastic with stainless steel reinforcement Quantity 1 valve Compatible Brand GE Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel or top of the cabinet, depending on your model. Have a towel or shallow pan ready, since residual water will spill out when you disconnect the lines. Photograph the wiring and hose connections before disconnecting anything — this valve has multiple inlets and outlets, and reconnecting one in the wrong position can cause a fill or temperature issue. Disconnect the water supply lines from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new WH23X29538 in the same position, reconnect all outlet hoses to their original positions exactly as photographed, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply lines, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm correct fill behavior and water temperature. Tools needed: Phillips screwdriver, pliers, towel or shallow pan, work gloves. Frequently Asked Questions My washer won't stop filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve. A worn internal seal on one of the four solenoid coils can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. My water temperature seems off during the wash. Could this valve be the cause? Yes. Because this valve has two separate inlets (hot and cold) and multiple solenoid coils that blend water to reach the correct temperature for each cycle setting, a fault in one of those coils can throw off the temperature blend even while the washer otherwise fills normally. This is a documented symptom this valve resolves. Is this the same as WH23X29553? The numbers are very close. No, these are two separate GE valve part numbers with completely different cross-reference sets and different compatible model series — this WH23X29538 serves the GFW550 series, while WH23X29553 serves the GFW650/850 and PFW870/950 series. Always confirm the exact part number from your washer's parts diagram rather than assuming based on a close number match. Is this a genuine OEM part? This is an OE (Original Equipment) part sold under our XPARTCO brand. OE parts are manufactured by the same original supplier that produces the Genuine OEM part, so the fit, materials, and performance are identical — the difference is that OE parts ship in XPARTCO packaging rather than the appliance manufacturer's branded box, which is why we can't list them as Genuine OEM. This gives you factory-original quality at a more affordable price than the branded version. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681EA2001T Washer Drain Pump Motor The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase. This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more. Common Problems This Part Fixes OE error code displayed — washer cannot drain within the allotted time Washer not draining — standing water remaining in the drum after a cycle Loud humming or buzzing during the drain cycle — motor running but impeller not turning Grinding or rattling noise during draining — physical damage to pump components Washer stopping mid-cycle due to a drain fault Washer draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. 4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T. Compatibility This drain pump motor is compatible with select front-load washers from the following brands: LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series Kenmore / Sears front-load washers (select LG-built models, including 796-series) Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models Spin speed: 1,100–1,200 RPM for powerful, efficient drainage Includes pump impeller and removable filter housing with sealing ring Removable filter housing allows easy cleaning without full pump disassembly Sealing ring reduces vibration and noise during operation Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles Motor assembly only — installs into existing pump housing, no housing replacement needed Resolves OE error code on compatible LG and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 4681EA2001T Also Replaces 4681EA2001N (updated current replacement) Part Type Washer Drain Pump Motor Assembly Condition Aftermarket Replacement Application LG and Kenmore Front-Load Washers Voltage 120V – 127V AC Frequency 60 Hz Wattage 85W Amperage 1.4A Flow Rate 45 liters per minute Spin Speed 1,100 – 1,200 RPM Material Metal / ABS Plastic Includes Motor assembly, impeller, removable filter housing, sealing ring Note Motor assembly only — existing pump housing is reused Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan. Frequently Asked Questions What is the difference between 4681EA2001T and 4681EA2001N? These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order. What does the OE error code mean on an LG washer? OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement. Does this include the pump housing? No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced. Should I check the drain filter before replacing the pump motor? Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X29528 Washer Door Lock The XPARTCO WH01X29528 is an aftermarket replacement door lock assembly compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Monogram front-load washing machines — as well as select GE UltraFast 2-in-1 combo washer/dryer units. The door lock is a safety mechanism mounted at the front of the washer where the door closes — it automatically engages when the door is shut, securing it closed for the entire wash and spin cycle so water and detergent can't spill out and cause injury. It also signals the control board that the door is safely locked, which is what allows the washer to start filling and running. When the door lock fails, the washer typically won't start, won't lock the door, stops mid-cycle, or throws a door-related error code. Rated 120 VAC, 60Hz, 16A. Failure usually comes from physical damage or normal wear over time. As a direct replacement for the GE WH01X29528, it also replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 (additional production markings: ITW 12070-71, V13305, 0024000128GE). Installation is straightforward with no wiring modifications — remove the old lock and install the new one, typically in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO WH01X29528 Washer Door Lock fixes GE, GE Profile, Café, and Haier front-load washers (and GE UltraFast 2-in-1 combo units) where the door won't lock or unlock, the washer won't start, the washer stops mid-cycle, the door feels loose or won't seal, or a door-latch error code appears. 120 VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, PS12749276, PD00060769, 4958749. Compatible with GE GFW510, GFW550, GFW650, GFW850, PFW870, PFW950, PFQ97 series front-load washers. No wiring modifications — installs in 10–15 minutes. Common Problems This Part Fixes Washer door won't lock at the start of the cycle Washer won't start — control board not detecting a locked door Washer door won't unlock at the end of the cycle Washer stops mid-cycle due to a door lock fault Door-latch related error code displayed on the control panel Door feels loose or doesn't seal properly Excessive noise and shaking while the washer is running (related to a door not securing properly) Intermittent locking — washer sometimes starts, sometimes doesn't Door lock assembly visibly broken, cracked, or with a failed latch Burning/electrical smell or humming from the door lock area (failed lock solenoid) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AGE26402, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, OEM20955948, V13305, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock assembly is compatible with select front-load washing machines and combo washer/dryer units from the following brands: GE front-load washers — GFW510 series (GFW510SCN0WW–SCN5WW, GFW510SCV0WW) GE front-load washers — GFW550 series (GFW550SPN0DG–SPN3DG, GFW550SPR0RS/SPR3RS/SPR4RS/SPR5RS, GFW550SSN0WW–SSN5WW) GE front-load washers — GFW650 series (GFW650SPN0SN–SPN4SN, GFW650SSN0WW–SSN4WW) GE front-load washers — GFW655 series (GFW655SPV0DS, GFW655SSV0WW) GE front-load washers — GFW850 series (GFW850SPN0DG–SPN5RS all DG/RS variants, GFW850SSN0WW–SSN5WW) GE Profile front-load washers — PFW870 series (PFW870SPV0RS, PFW870SSV0WW), PFW950 series (PFW950SPT0DS/SPT1DS/SPT2DS) GE Profile combo units — PFQ97HSPV0DS (UltraFast 2-in-1 combo washer/dryer) GE Café, Haier, Hotpoint, RCA, Monogram — select front-load models using the same door lock Sears Kenmore and Crosley — select GE-built front-load models Always verify your appliance model number before ordering. The WH01X29528 fits the specific models listed — please double-check your model number. Contact our support team if you're unsure. Key Features Door lock and switch assembly — locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Prevents the door from being opened mid-cycle, keeping water and detergent safely contained Resolves "won't lock," "won't unlock," "won't start," "stops mid-cycle," and door-latch error codes when caused by a failed lock Rated 120 VAC, 60Hz, 16A — correct electrical specifications for compatible GE front-load washers Integrates with the washer's main control board, door switch, and load detection system Durable, moisture-resistant materials resist deformation, wear, and short circuits for long service life No wiring modifications required — direct-fit replacement using the original connector Replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 Compatible with GE GFW510/GFW550/GFW650/GFW850, PFW870/PFW950, and PFQ97 series front-load washers and UltraFast combo units, plus select Café, Haier, Hotpoint, RCA, Monogram, Kenmore, and Crosley GE-built models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPWH01X29528 Part Type Washer Door Lock and Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers & Combo Washer/Dryer Units (GE platform) Voltage 120 VAC Frequency 60 Hz Amperage 16A Additional Production Markings ITW 12070-71, V13305, 0024000128GE Function Locks door during wash/spin; signals control board door is secure Location Front of washer at the door opening Compatible Brands GE, GE Profile, Café, Haier, Hotpoint, RCA, Monogram, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, you may need to access the manual release. Peel back the rubber door boot/gasket from the front panel edge near the lock to expose the door lock assembly — on some models this requires releasing the spring-loaded wire clamp that secures the boot with needle-nose pliers. Photograph the wire harness connection before disconnecting anything. Remove the mounting screws holding the door lock assembly to the front panel. Reach in and pull the assembly out through the door opening far enough to access the wire connector. Disconnect the wire harness plug from the old assembly (no wiring modifications are needed — it's a direct plug connection). Snap the new WH01X29528 assembly onto the wire harness plug until it clicks firmly, position it in the front panel opening, and secure it with the mounting screws. Press the rubber door boot back into its groove and reinstall the spring-loaded wire clamp if applicable. Restore power and test by closing the door and starting a cycle — confirm the door locks, the washer runs, and the door unlocks at the end. Tools needed: Phillips screwdriver, needle-nose pliers, work gloves. Frequently Asked Questions My GE washer won't start and shows a door error — is this the part? Very likely, yes. GE front-load washers won't start unless the control board receives confirmation from the door lock that the door is closed and locked — it's a safety interlock. When the door lock fails, the washer either won't lock the door, won't start, or displays a door-related message on the panel. If your door appears to close normally but the washer won't begin the cycle (or stops shortly after starting), the door lock is the most common cause. Replacing the WH01X29528 typically resolves it. If you've already replaced the door lock and the problem persists, the issue may be the main control board instead. I replaced the door lock and it worked briefly, then failed again — what's wrong? If a new door lock works for a short time (seconds to minutes) and then the washer goes back to showing a door error, the problem may not be the lock itself but the main control board that powers and monitors it. A control board with a failing door-lock circuit can damage or fail to properly drive the lock, causing repeated symptoms even after replacing the lock. Some customers report an electrical smell or humming from the lock in these cases. If you've replaced the door lock (especially more than once) and the door error returns, the main control board is the next component to investigate. Contact our support team with your model number for the correct control board part. Does this fit the GE UltraFast 2-in-1 combo washer/dryer? Yes — the WH01X29528 is used on select GE UltraFast 2-in-1 combo washer/dryer units (such as the PFQ97HSPV0DS) in addition to standalone GE front-load washers. The combo units use the same door lock design as the front-load washers in the GFW/PFW families. As always, confirm your specific model number against the compatibility list before ordering, since GE uses different door locks across different washer generations. How do I open the door if it's stuck locked and the washer won't run? If the door is stuck in the locked position because of a failed lock, first make sure there's no water in the drum (run or complete a drain cycle if possible). Then unplug the washer and wait a few minutes — some GE models release the lock after power is removed. If it's still stuck, most front-load washers have a manual release mechanism accessible from behind the lower kick panel at the front of the machine — a tab or cord you pull to manually disengage the lock. Consult your model's manual for the manual release location. Once the door is open, you can proceed with replacing the lock. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable, moisture-resistant materials to match the electrical specifications (120 VAC, 60Hz, 16A), connector configuration, mounting, and door-locking function of the original WH01X29528 door lock used in compatible GE, GE Profile, Café, Haier, and related front-load washers and combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE4M488 Dryer Control Board   Replaces Part Numbers: WE4M488, 2218486, WE4M331, WE4M388, AH3487192, EA3487192, AP4980176, PS3487192.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

285805 Genuine OEM Whirlpool Washer Water Inlet Valve The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves. This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517. Quick Answer The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer won't stop filling — overfilling past the normal level Water leaking or dripping from the washer after the cycle has ended No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cycle stalling at the fill step and never advancing to wash Hot water inlet blocked by calcium or mineral deposits after years of hard-water use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including: Whirlpool top-load washers and laundry centers Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Complete kit — includes mounting bracket, screws, and installation instructions Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform Approximately 5.7" tall, metal and plastic construction Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 285805 Part Type Washer Water Inlet Valve Kit Condition Genuine OEM Brand Whirlpool Application Direct-Drive Top-Load Washers / Laundry Centers Kit Contents Water inlet valve, mounting bracket, screws, instructions Ports 2 (hot and cold) Hose Compatibility 1/2" ID Thread Specification Two 3/4"-11 x 1/2" NHT hose threads Height Approx. 5.7 in. Material Metal and plastic Color Blue or green (both correct — varies by production run) Quantity 1 valve kit Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions My valve is blue but the old one was green (or vice versa). Did I get the wrong part? No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance. The new valve's bracket doesn't match my old one. What do I do? This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent. Only hot water won't fill, but cold works fine. Is that this valve? Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled. My washer won't stop filling. Is that dangerous, and is it this valve? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less