Search results for "washer board"

285805 Genuine OEM Whirlpool Washer Water Inlet Valve The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves. This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517. Quick Answer The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer won't stop filling — overfilling past the normal level Water leaking or dripping from the washer after the cycle has ended No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cycle stalling at the fill step and never advancing to wash Hot water inlet blocked by calcium or mineral deposits after years of hard-water use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including: Whirlpool top-load washers and laundry centers Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Complete kit — includes mounting bracket, screws, and installation instructions Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform Approximately 5.7" tall, metal and plastic construction Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 285805 Part Type Washer Water Inlet Valve Kit Condition Genuine OEM Brand Whirlpool Application Direct-Drive Top-Load Washers / Laundry Centers Kit Contents Water inlet valve, mounting bracket, screws, instructions Ports 2 (hot and cold) Hose Compatibility 1/2" ID Thread Specification Two 3/4"-11 x 1/2" NHT hose threads Height Approx. 5.7 in. Material Metal and plastic Color Blue or green (both correct — varies by production run) Quantity 1 valve kit Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions My valve is blue but the old one was green (or vice versa). Did I get the wrong part? No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance. The new valve's bracket doesn't match my old one. What do I do? This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent. Only hot water won't fill, but cold works fine. Is that this valve? Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled. My washer won't stop filling. Is that dangerous, and is it this valve? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X26637 Genuine OEM GE Washer Water Inlet Valve The WH13X26637 is a Genuine OEM GE replacement quad water inlet valve assembly compatible with select GE and GE Profile top-load washers in the GTW, GTV, GTN, PTW, and related series. This is a quad (4-solenoid) valve assembly that controls the flow of hot water, cold water, bleach dispenser water, and fabric softener dispenser water from the household supply lines into the washer tub and dispenser compartments. Each solenoid port is independently controlled by the washer's control board. When any port fails, the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or drip water between cycles. As a Genuine OEM part manufactured by GE to factory specifications, the WH13X26637 is a direct current-production replacement for the earlier WH13X24058. It measures approximately 7"L x 3"W x 3"H with multi-colored ports (blue, green, red, tan, silver, and gold) for easy identification of each solenoid's function. It directly replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PD00037665, and PS12171559. Installs in 20–30 minutes with basic hand tools. Quick Answer The WH13X26637 Genuine OEM GE Washer Water Inlet Valve fixes GE top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or drip water between cycles. Quad (4-solenoid) valve. Approx. 7"L x 3"W x 3"H. Multi-color port identification. Genuine OEM. Replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PS12171559. Compatible with GE GTW, GTV, GTN, PTW series top-load washers. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more solenoid ports partially blocked or failing Washer filling with only cold or only hot water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach not dispensing during the wash cycle Fabric softener not dispensing at the rinse cycle point Water dripping into the tub between cycles — valve port not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, WH13X24058, AGE26282, AP6282070, EAP12171559, PD00037665, PS12171559. WH13X26637 is the current updated part number superseding WH13X24058. If your washer's parts diagram shows WH13X24058, the WH13X26637 is the correct current replacement. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select GE and GE Profile top-load washers from the following series: GE washers — GTW680 series (GTW680BPL0DG, GTW680BPL1DG, GTW680BPL2DG, GTW680BSJ0WS, GTW680BSJ1WS, GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS and related models) GE washers — GTW685 series (GTW685BPL0DG, GTW685BPL1DG, GTW685BSL1WS, GTV685BSL0WS and related models) GE washers — GTW720 series (GTW720BPN0DG, GTW720BSN0WS and related models) GE washers — GTW725 series (GTW725BPN0DG, GTW725BSN0WS and related models) GE washers — GTW750 series (GTW750CPL0DG, GTW750CPL1DG, GTW750CSL0DG, GTW750CSL0WS, GTW750CSL1WS and related models) GE washers — GTW755 series (GTW755CPM0DG, GTW755CSM0WS, GTW755CSM1WS and related models) GE Profile washers — PTW600, PTW605, PTW700, PTW705 series and related models GE washers — GTN755 series (GTN755CPM1DG and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Quad (4-solenoid) valve assembly — independently controls hot water, cold water, bleach dispenser, and fabric softener dispenser ports Multi-colored ports for easy solenoid identification during installation Dimensions: approximately 7"L x 3"W x 3"H Current updated part number — directly supersedes WH13X24058 Compatible with GE GTW680, GTW685, GTW720, GTW725, GTW750, GTW755, PTW600, PTW605, PTW700, PTW705, GTN755 series top-load washers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH13X26637 Supersedes WH13X24058 Part Type Washer Water Inlet Valve Assembly (Quad / 4-Solenoid) Condition Genuine OEM Application GE and GE Profile Top-Load Washers Solenoids 4 (hot, cold, bleach, fabric softener) Dimensions Approximately 7"L x 3"W x 3"H Port Colors Multi-color (blue, green, red, tan, silver, gold) Material Plastic / Metal Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel and remove it to expose the valve assembly. Photograph all wire harness connections and hose routing — the multi-color ports make this straightforward. Disconnect the two external supply hoses from the hot and cold inlet ports. Disconnect the internal outlet hoses by releasing the retaining clips. Disconnect the wire harness connectors from each solenoid terminal. Unscrew the mounting bolts and remove the old valve. Install the new WH13X26637 valve in the same position, reconnect all hoses and wire harnesses in the documented positions, and secure the mounting bolts. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, socket wrench, needle-nose pliers. Frequently Asked Questions What is the difference between WH13X26637 and WH13X24058? These are the same quad water inlet valve assembly — WH13X26637 is the current updated part number that GE issued to supersede the earlier WH13X24058. If your washer's documentation, parts diagram, or old valve label shows WH13X24058, the WH13X26637 is the correct current replacement to order. Both are quad (4-solenoid) valve assemblies with the same port configuration and function. What does each solenoid port on this quad valve control? The WH13X26637 quad valve has four independently operated solenoid ports. The hot water port opens to supply hot water from the household supply line. The cold water port supplies cold water. The bleach dispenser port delivers cold water through the bleach compartment at the appropriate point in the wash cycle. The fabric softener port delivers water through the softener compartment during the rinse cycle. When any single solenoid fails, only the function it controls is affected — the rest of the valve continues to work normally. My washer won't fill and shows an error code — is it the water inlet valve? A fill error code on compatible GE models commonly points to the water inlet valve. Before replacing the valve, confirm that both supply valves behind the washer are fully open, neither supply hose is kinked, and the household water pressure is adequate. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed and the valve needs replacement. If all coils test good but the washer still won't fill, the issue may be with the control board or water pressure. My washer fills fine but won't dispense fabric softener — could it be the valve? Yes — if only the fabric softener dispenser function is affected, the solenoid coil controlling that specific port has likely failed. Since it is part of the same quad valve assembly, replacing the entire WH13X26637 assembly resolves the failed port. Individual solenoid ports cannot be replaced — the complete quad valve assembly must be replaced when any port fails. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same quad water inlet valve assembly installed in compatible GE and GE Profile top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

280146 Washer Motor Rotor  Product Condition: Genuine OEM New / Old Stock   Replaces Part Numbers: 280146, 1175771, 8565177, AH993018, EA993018, AP3882831, PS993018.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11168740 - W11168743 Washer Water Valve Set for W11127357 Cold and Hot Washer Water Inlet Valve Housing and Wire Harness not included. Fits Kenmore, Maytag, Whirlpool top load washer models. Replaces Part Number:W11168740, WPW10240949, W10240949, W10921514, AP6285450, PS12348073, W11127357, W11127357, W10678672, W10678676, W10849466, W10921581, W11085642, AP6261887, PS12347475, W11168743, WPW10240948, W10240948, W10921515, AP6327638, PS12348074. Description: This Water Inlet Valve set is a replacement part for specific Kenmore, Maytag, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W10810403 Washer Lid Switch Assembly The XPARTCO W10810403 is an aftermarket replacement lid lock assembly for Whirlpool Cabrio and Maytag Bravos XL top-load washers. Positioned on the underside of the washer lid, this assembly detects whether the lid is open or closed and locks it shut during the wash cycle, preventing the washer from spinning or agitating — and preventing the lid from being opened — while the cycle is running. This is a safety mechanism as much as a functional one, keeping users from contacting moving parts or being splashed by water or detergent mid-cycle. This assembly includes the lid lock mechanism and its wiring harness, and ships with a white bezel. Many of these lid locks also contain an internal fuse as part of the switch circuit — if that fuse blows, the symptom isn't limited to lid-related errors; it can prevent the entire control board from powering up at all, since the switch sits in the same circuit path. A failing lid lock typically shows up as the lid not closing or locking properly, the washer failing to start, the cycle stopping mid-way, or in more severe cases, a completely unresponsive control panel with no lights at all. It directly replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, and PS11731620. Quick Answer The XPARTCO W10810403 Washer Lid Switch Assembly fixes Whirlpool Cabrio, Maytag Bravos XL, and select Kenmore 600/700 Series top-load washers where the lid won't lock, the washer won't start, the cycle stops mid-way, or the control panel is completely unresponsive with no lights. White bezel. Replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, PS11731620. If your original lock has a grey bezel, you need part number W10861642 instead — same mechanism, different bezel color, so match the color of your existing lock before ordering. Common Problems This Part Fixes Lid won't lock or lock reliably during the cycle Lid won't open after a cycle finishes Washer won't start Washer won't agitate or spin because the lid isn't sensed as locked Cycle stops partway through Washer pumps but won't spin Control panel completely unresponsive with no lights, potentially from an internal fuse in the switch circuit Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select Whirlpool Cabrio and Maytag Bravos XL top-load washers, and also fits select Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea washers built on the same platform, including model numbers such as MVWB855DW1, MVWB865GW1, MVWB835DW3, and MVWB765FW4. Note — bezel color and lid lock platform both matter: This assembly has a white bezel. If your original lock has a grey bezel, order W10861642 instead — same lock mechanism, different bezel color. Separately, Whirlpool has used several distinct lid lock designs across its Cabrio-era washer lineup, including a different 3-wire electronic lock (our W11670519 listing) used on other Cabrio/MVW models. These are not the same part despite both serving Cabrio-platform washers. Always verify your full model number and match your original lock's exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement lid lock assembly — includes the lock mechanism and wiring harness Resolves "lid won't lock," "washer won't start," "cycle stops mid-way," and "unresponsive control panel" symptoms White bezel finish Safety mechanism that prevents lid opening and drum movement from occurring at the same time Direct drop-in replacement — mounts to the original position on the underside of the lid Replaces W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 Compatible with Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10810403 OEM Part Number W10810403 Part Type Washer Lid Lock/Switch Assembly Condition Aftermarket Replacement Application Whirlpool Cabrio / Maytag Bravos XL Top-Load Washers Bezel Color White (grey bezel = W10861642) Included Components Lid lock mechanism + wiring harness Location Underside of the washer lid Repair Difficulty Easy — basic hand tools Quantity 1 lid switch assembly Compatible Brands Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, Ikea Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the washer lid and locate the lid lock assembly mounted on its underside, typically secured with a couple of screws. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws, disconnect the wiring harness connector from the old assembly, and pull it free. Install the new W10810403 in the same position, reconnect the wiring harness connector fully, and secure the mounting screws. Restore power and run a test cycle to confirm the lid locks securely, the washer starts and completes a full cycle, and the lid unlocks normally once finished. Tools needed: multi-screwdriver, work gloves. Frequently Asked Questions My control panel has no lights at all. Could the lid lock really cause that? Yes, and this is a less obvious but documented cause. Some of these lid lock assemblies include an internal fuse as part of the switch circuit. If that fuse blows, it can prevent the control board from powering up entirely, producing a completely dark, unresponsive panel rather than a symptom that's obviously tied to the lid. If your washer has no lights and no response at all, this lock assembly is worth checking alongside the more obvious suspects. My old lock has a grey bezel. Can I still use this part? This specific listing has a white bezel. If your original lock is grey, order part number W10861642 instead — it's the same lock mechanism, just finished with a grey bezel to match certain washer trim colors. Using the wrong bezel color won't affect function, but it will look mismatched against your washer's lid. Is this the same lock used on all Cabrio washers? No — Whirlpool has used more than one lid lock design across its Cabrio-era lineup. This W10810403 is a distinct assembly from other Cabrio/MVW-platform locks, such as our W11670519 listing, which uses a different 3-wire electronic locking design. Always match your exact original part number rather than assuming any "Cabrio lock" will fit, since the mounting and electrical interface can differ between designs. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the locking mechanism, wiring harness, and bezel design of the original W10810403 lid lock assembly used in compatible Whirlpool Cabrio, Maytag Bravos XL, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH11X39237 Washer Drain Pump The XPARTCO WH11X39237 is an aftermarket replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH11X39237 Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Aftermarket replacement built to OEM-equivalent quality standards Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Aftermarket Replacement Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical specifications and physical dimensions of the original WH11X39237 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WP389140 Genuine OEM Whirlpool Washer Drive Block The WP389140 is a genuine Whirlpool OEM drive block for large-capacity belt-drive and direct-drive top-load washers. This is a purely mechanical coupling component: it connects the inner spin basket to the transmission's drive shaft, so that when the transmission turns, the basket turns with it. Without a properly seated drive block, the connection between the motor's rotational power and the basket is lost or unreliable, even though every electrical component in the washer may be working perfectly. Measuring approximately 2-5/16" high, this drive block is a wear component subject to gradual mechanical stress every time the washer agitates or spins. A worn or failed drive block produces a distinctive set of symptoms: the basket may spin freely without properly engaging, the washer may spin slowly and leave clothes excessively wet, or you may hear a loud knocking or banging noise during operation as the connection between the basket and drive shaft becomes loose or worn. It directly replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, and 2858. Quick Answer The WP389140 Genuine OEM Whirlpool Washer Drive Block fixes Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis top-load washers with a basket that spins freely without engaging, slow spinning that leaves clothes excessively wet, or loud knocking/banging noise during operation. Approximately 2-5/16" high. For large-capacity belt-drive and direct-drive washers. Replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, 2858. This repair typically requires a spanner wrench to remove a large securing nut — budget for the right tool before starting. Common Problems This Part Fixes Washer basket spins freely without properly engaging during the wash or spin cycle Washer spins slowly, leaving clothes excessively wet at the end of a cycle Loud knocking or banging noise during operation Washer shakes or moves noticeably during spin Basket continues spinning after the cycle should have stopped Inefficient wash and spin cycles overall due to poor basket engagement Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive block directly replaces the following OEM and cross-reference part numbers: WP389140, 389140, 357782, 97360, PD00002363, EAP11741977, WP389140VP, AP6008836, AWP47839, J27-936, PS11741977. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive block is compatible with select Whirlpool large-capacity top-load washers (belt-drive and direct-drive), and also fits select Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis washers built on the Whirlpool platform, including model numbers such as: NTW4516FW, NTW4516FW3, NTW4516FW4 WTW4816FW2, WTW4816FW3 RTW4516FW, NTW4605EW, WTW4800BQ Note: Always verify your full model number before ordering, since Whirlpool uses different drive block designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified fit for a secure basket-to-transmission connection Connects the inner spin basket to the transmission's drive shaft Resolves "basket spins freely," "slow spin, clothes too wet," and "loud knocking noise" symptoms caused by drive block wear Approximately 2-5/16" high Designed for large-capacity belt-drive and direct-drive washer platforms Direct drop-in replacement matching the original fit onto the spin tube notches Replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, and 2858 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP389140 Part Type Washer Drive Block Condition Genuine OEM Brand Whirlpool Application Large-Capacity Belt-Drive and Direct-Drive Top-Load Washers Height Approx. 2-5/16 in. Function Connects the inner spin basket to the transmission drive shaft Related Component Drive cam (commonly inspected/replaced during the same repair) Repair Difficulty Moderate — spanner wrench and washer disassembly required Quantity 1 drive block Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, Inglis Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Spanner Wrench Required Disconnect power at the outlet or shut off the circuit breaker, and shut off the hot and cold water supply valves before beginning. Wear work gloves. Remove the washer's top and control console per your model's service instructions to access the inner tub assembly. Remove the agitator and any hardware securing the basket, which typically includes a large center nut — a spanner wrench is required to remove this nut, along with a socket and long extension for other fasteners; expect to remove a fair number of components to fully access the drive block. Lift the wash basket out to expose the drive block, which sits on the spin tube near the center of the transmission. Photograph the orientation of the old drive block and any surrounding hardware before removing it. Lift the old drive block free, and while it's accessible, inspect the drive cam nearby for wear as well, since it's commonly replaced at the same time. Slide the new WP389140 drive block into position, making sure it seats fully onto the spin tube notches, and reassemble the basket, hardware, agitator, console, and top panel in reverse order. Restore water and power, then run a test cycle through both wash and spin to confirm the basket engages properly with no unusual noise. Tools needed: multi-screwdriver, spanner wrench, socket set with long extension, work gloves. Frequently Asked Questions My washer basket spins freely and doesn't seem connected to anything. Is this the drive block? Yes, this is the classic symptom of a failed drive block. Since this component is the mechanical link between the transmission's drive shaft and the inner spin basket, once it wears out or fails, the basket can spin independently without properly engaging, even though the motor and transmission are working normally. Do I really need a spanner wrench for this repair? Yes, on most models. Accessing the drive block requires removing a large nut that secures the basket assembly, and this nut is specifically designed to be removed with a spanner wrench rather than a standard socket. Trying to remove it without the correct tool risks damaging the nut or the surrounding components, so it's worth having one on hand before you start. Should I replace the drive cam at the same time? It's worth inspecting while you have the assembly open, since the drive cam sits in the same area and is commonly replaced alongside the drive block when a technician is already this far into the repair. If it shows visible wear, replacing both at once saves you from repeating this same teardown again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original dimensions and fit of the drive block originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR55X10942C Refrigerator Control Board The XPARTCO WR55X10942C is an aftermarket replacement main control board for GE, Hotpoint, RCA, and select Kenmore refrigerators. This board is the central processor for the refrigeration system — it regulates temperature, manages the defrost cycle, and controls compressor operation, coordinating everything that keeps both the fresh food and freezer compartments at the correct temperature. Electrical surges and ordinary long-term wear are both common causes of this board failing. Manufacturer part number 200D4850G022. A failing control board produces a wide range of symptoms because so many functions run through it: inconsistent or fluctuating temperatures, a refrigerator that runs too warm or too cold, the refrigerator not starting at all, unusual clicking noises as the board misfires relay signals, or ice that melts and refreezes as the defrost cycle malfunctions. It directly replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, WR55X10024, WR55X10037, WR55X10045, WR55X10056, WR55X10065, WR55X10079, WR55X10083, WR55X10086, WR55X10090, WR55X10097, WR55X10109, WR55X10110, WR55X10151, WR55X10160, WR55X10171, WR55X10174, WR55X10177, WR55X10187, WR55X10188, AP7188100, and PS16729744. Quick Answer The XPARTCO WR55X10942C Refrigerator Control Board fixes GE, Hotpoint, RCA, and select Kenmore refrigerators with inconsistent temperatures, a fridge running too warm or too cold, the unit not starting, clicking noises, or ice that melts and refreezes from a malfunctioning defrost cycle. Manufacturer part number 200D4850G022. Replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, WR55X10024, WR55X10037, WR55X10045, WR55X10056, WR55X10065, WR55X10079, WR55X10083, WR55X10086, WR55X10090, WR55X10097, WR55X10109, WR55X10110, WR55X10151, WR55X10160, WR55X10171, WR55X10174, WR55X10177, WR55X10187, WR55X10188, AP7188100, PS16729744. GE has released many similar-looking control boards across its refrigerator generations — always confirm your exact model number before ordering, since boards that look alike are not always interchangeable. Common Problems This Part Fixes Refrigerator temperatures fluctuating or running inconsistently Refrigerator running too warm or too cold Refrigerator not starting at all Unusual clicking noises from the refrigerator Ice melting and refreezing due to a malfunctioning defrost cycle Refrigerator or freezer section not cooling properly Symptoms that began suddenly, potentially following an electrical surge Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator control board directly replaces the following OEM and cross-reference part numbers: WR55X10942C, WR55X10942, WR55X10942P, WR49X10060, WR55X10065, WR55X10160, WR55X10187, WR55X10328, WR55X10333, WR55X10335, WR55X10336, WR55X10339, WR55X10358, WR55X10366, WR55X10372, WR55X10379, WR55X10381, WR55X10385, WR55X10396, WR55X10413, WR55X10416, WR55X10426, WR55X10427, WR55X10432, WR55X10436, WR55X10456, WR55X10473, WR55X10474, WR55X10523, WR55X10524, WR55X10526, WR55X10529, WR55X10543, WR55X10552, WR55X10554, WR55X10558, WR55X10589, WR55X10597, WR55X10603, WR55X10606, WR55X10614, WR55X10616, WR55X10626, WR55X10656, WR55X10659, WR55X10699, WR55X10712, WR55X10715, WR55X10722, WR55X10942CT, WR55X11036, AP7188100, AGE29813 PD00074367, 200D2259G017, 200D4850G022, 200D4852G018, 200D4852G024, 200D4854G008, 200D4854G013, 200D6221G013, 200D6221G015, 200D6221G016, WKKT 1304-00-70A. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control board is compatible with select GE and Hotpoint refrigerators, and also fits select RCA and Kenmore refrigerators built on the GE platform. Note — many similar-looking boards exist: GE has produced numerous refrigerator main control boards across different generations that can look nearly identical to this one, and not all of them are interchangeable despite the resemblance. Always verify your full refrigerator model number before ordering, rather than matching by appearance alone. Contact our support team with your model number and we will confirm fitment before you order. Key Features Aftermarket replacement main control board — regulates temperature, defrost, and compressor operation Resolves "inconsistent temperatures," "won't start," "clicking noises," and "ice melting and refreezing" symptoms caused by control board failure Includes built-in defrost controls Manufacturer part number 200D4850G022 Direct drop-in replacement for the original board mounting and harness connectors Replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, and a wide range of earlier WR55X-prefix board numbers listed above Compatible with GE, Hotpoint, RCA, and select Kenmore refrigerators Aftermarket replacement built to OEM-equivalent quality standards Moderately difficult repair, typically 15 to 45 minutes Product Specifications Part Number WR55X10942C OEM Part Number WR55X10942C (200D4850G022) Part Type Refrigerator Main Control Board Condition Aftermarket Replacement Brand GE Function Regulates temperature, defrost cycle, and compressor operation Repair Difficulty Moderate — 15 to 45 minutes Quantity 1 control board Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Handle The Board By Its Edges Unplug the refrigerator or shut off power at the breaker before beginning to avoid electrical hazards. Wear work gloves. Access is typically through a rear cover panel: remove the screws securing the cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and reconnecting one in the wrong position will cause a malfunction or no-start symptom. Handle the new board by its edges rather than touching the components directly, and avoid working in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Position the replacement WR55X10942C board in the same location, secure it in place, and reconnect all harnesses firmly, matching the original connector locations exactly as photographed. Put the rear cover back on and tighten the screws, then restore power and confirm normal cooling and defrost operation, along with any dispenser or interior lighting behavior your model has. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions My refrigerator temperature keeps fluctuating for no clear reason. Is this the control board? It's a strong possibility, especially if you've already ruled out simpler causes like a door seal that isn't sealing properly or a condenser coil that needs cleaning. Since this board regulates both temperature and the defrost cycle together, a failing board can cause the refrigerator to swing between too warm and too cold as it struggles to manage the system correctly. Could a power surge have caused this failure? Yes, this is a documented and common cause of control board failure. Electrical surges, including those from storms or grid fluctuations, can damage the board's circuitry outright, leading to sudden symptom onset. If your refrigerator's issues started abruptly, especially after a storm or power event, this board is a reasonable first suspect. There are so many similar GE control board part numbers. How do I make sure I'm ordering the right one? This is a real and common point of confusion, since GE has released many visually similar boards across different refrigerator generations that are not all interchangeable. The safest approach is to match your refrigerator's full model number against this listing's compatibility rather than relying on how similar a board looks to your old one. If you're at all unsure, send us your model number and we'll confirm fitment before you order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the processor, relay switching, defrost control circuitry, and harness connector configuration of the original WR55X10942C control board used in compatible GE, Hotpoint, RCA, and Kenmore refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 137221600 Washer Drain Pump The XPARTCO 137221600 is an aftermarket replacement washer drain pump compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers — including popular Affinity series and washer-dryer combo models. The drain pump is mounted at the base of the washer and is responsible for evacuating the wash and rinse water from the tub through the drain hose at the end of each cycle. When the drain pump fails, the washer can't drain — leaving clothes soaking wet, water pooling in the tub, and the wash cycle unable to advance to spin. Common failure symptoms include humming without pumping (blocked or seized impeller), leaks from the pump housing, loud grinding or clicking noises, and complete pump silence when a drain cycle should be running. Rated 120V AC, 60Hz, 85W, 1.25A. Based on the Askol M65 design, with a firmly attached red flapper to prevent drain backflow into the tub. Constructed from strong, durable plastic to resist cracking and leaking through many years of cycling. Package includes the drain pump, mounting base, and mounting screw. This part directly replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, and PS7783938. Important: before installing the new pump, clean any lint or debris from the rubber boot, verify the drain hose is clear and properly fastened, and check the pump filter for blockage — installing a new pump on a system with the underlying blockage will not resolve the drainage problem. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 137221600 Washer Drain Pump fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers that won't drain, leave clothes soaking wet, are noisy or humming during the drain cycle, or display an E11 error code. 120V AC, 60Hz, 85W, 1.25A. Askol M65 design with red backflow flapper. Kit includes pump + mounting base + screw. Replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, PS7783938. Common Problems This Part Fixes Washer not draining — pump failed to remove water at the end of the wash or rinse cycle Clothes left soaking wet at the end of the cycle — no drain, so no spin can start Water leaking from the bottom of the washer — cracked pump housing or failed seal Loud humming noise but no water flowing — pump motor running against a seized impeller or blockage Grinding, clicking, or unusual noises during the drain cycle E11 error code displayed on the control panel (drain fault) Washer pumps but won't spin — drain cycle can't complete, blocking spin Cycles taking much longer than normal as the washer tries to drain Pump silent during drain — motor windings open or electrical fault Impeller broken, cracked, or missing pieces after opening the pump Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: 137221600, 131724000, 134051200, 134740500, 137108100, 137151800, 137151800KITK, 2754548, TJ137108100, ER137108100, PD00000118, EAP7783938, BPX401-72J, AFR14249, AP5684706, PS7783938, Also replaces GE WH23X10041, 2119312, WH23X10009, WH23X10017, WH23X10031, WH23X10034, AH3502779, EA3502779, AP5324214, PS3502779. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers and washer-dryer combos from the following brands: Frigidaire front-load washers — Affinity series (FAFW3001LW3, FAFW3801LW3 and related), FEX831FS2/FS4, FTF2140ES1, FWS445RFS2, FWX445RFS3 series Frigidaire front-load washers — ATF6000ES1, ATF8000FS1, ATFB6700FS0 series Frigidaire front-load washers — GLTF2940ES3, GLTF2940FS1 and related GLTF series Frigidaire washer-dryer combos — CWS3600AS1 and related Electrolux front-load washers — select models Crosley front-load washers — select models Gibson front-load washers — select models Kelvinator front-load washers — select models Kenmore / Sears front-load washers — select Frigidaire-built models (41744052400, 41744052401, 41744052500, 41744082500, 41748102700, 41748106700, 41748116700, 41790812995 and related 417-series) Tappan front-load washers — select models Westinghouse front-load washers — select models Note: The redesigned 137221600 may look slightly different from your original (e.g., white or gray housing vs. original black), but functions identically. Ensure proper orientation and flapper alignment during installation. Always verify your appliance model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Drain pump — removes water from the washer tub through the drain hose at the end of the wash and rinse cycles Resolves "won't drain," "won't spin," "wet clothes," "E11 error," and "humming pump" symptoms 120V AC, 60Hz, 85W, 1.25A — correct electrical specifications for compatible Frigidaire-platform washers Askol M65 design with red backflow flapper to prevent water from flowing back into the tub Strong, durable plastic construction resistant to cracking and leaking Kit includes: 1x drain pump, 1x mounting base, 1x mounting screw Replaces 15+ OEM and cross-reference part numbers including 137108100, 137151800, 131724000, 134051200, 134740500, 134740800, AP5684706, and PS7783938 Compatible with Frigidaire (Affinity, FEX, FTF, FWS, FWX, ATF, ATFB, GLTF, CWS series), Electrolux, Crosley, Gibson, Kelvinator, Kenmore (417-series), Tappan, and Westinghouse front-load washers and washer-dryer combos DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP137221600 Part Type Washer Drain Pump Condition Aftermarket Replacement Application Front-Load Washers and Washer-Dryer Combos (Frigidaire/Electrolux platform) Voltage 120V AC Frequency 60 Hz Wattage 85W Amperage 1.25A Design Askol M65 with red backflow flapper Material Durable plastic Includes 1x Drain Pump, 1x Mounting Base, 1x Mounting Screw Error Codes Resolved E11 (drain fault) Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Check for Blockage First Disconnect power at the outlet or breaker and shut off both water supplies at the wall before beginning. Wear work gloves to protect your hands — pump components can have sharp edges. Have towels ready — residual water remains in the pump housing and hoses. Important: before replacing the pump, check for the underlying cause of the drain problem. Inspect the pump filter (accessible on many models via the lower front kick panel), the drain hose for kinks, and the rubber boot at the bottom of the tub for lint, coins, buttons, or other debris — installing a new pump on a system with an unresolved blockage will not fix the drain problem. Remove the appropriate access panel (typically the rear or front lower kick panel — model-dependent) to expose the pump. Photograph the wire harness and hose connections before disconnecting. Disconnect the electrical wire connectors from the pump motor. Squeeze the hose clamps with pliers and slide them back to release the tub-to-pump hose and the pump-to-drain-hose from the pump. Remove the 2 mounting screws holding the pump to its base and lift the old pump out. Clean any residual debris from the rubber boot, hoses, and pump filter area. Install the new 137221600 pump using the included mounting base and screw. Reconnect the hoses with the clamps, orient the red backflow flapper correctly, and reconnect the electrical connectors. Reinstall the access panel, restore water and power, and run a rinse cycle to test drainage and check for leaks at all connections. Tools needed: Phillips screwdriver, needle-nose pliers, channel-lock pliers, small flathead screwdriver, towel, work gloves. Frequently Asked Questions My washer won't drain — is it always the pump? Not always. Before replacing the pump, check for these common causes: 1) Clogged pump filter — most Frigidaire front-load washers have a filter accessible via the lower front kick panel; coins, buttons, lint, and small items can block it. 2) Kinked or clogged drain hose — inspect the entire drain hose from the pump to the wall standpipe or sink. 3) Blocked rubber boot — small items can get stuck between the tub and the pump inlet. 4) Failed lid lock/door switch — if the washer doesn't detect a locked door, it won't run the drain cycle. If all of these check out and the pump still isn't draining (or is humming without moving water), the pump has failed and this is the correct repair. What is the E11 error code on my Frigidaire washer? E11 on Frigidaire and Electrolux front-load washers indicates a drain fault — the control board is not detecting successful drainage within the expected time. Common causes are a failed drain pump, a clogged pump filter, a kinked or clogged drain hose, or debris blocking the impeller. If you've verified the filter and hose are clear but the code persists, replacing the 137221600 drain pump typically resolves it. If the code returns after replacement, check the wire harness between the pump and the control board. Does the pump come with everything I need for installation? Yes — the 137221600 (OE) package includes the drain pump itself, a mounting base, and a mounting screw. This is everything you need for the pump replacement itself. However, you should reuse the original hose clamps and hoses from your old pump (they should still be in good condition). If you find that the rubber boot at the base of the tub is cracked, hardened, or torn during the repair, that's a separate part that would need to be ordered — inspect it before completing the reinstallation. The new pump looks different from my old one — is it the right part? Very likely, yes. The 137221600 has been through several revisions over its production history — some housings are black, others white or gray, and the exact shape can vary slightly across production runs. As long as the mounting bolt pattern, hose inlet/outlet sizes, and electrical connector are the same, and the specs match (120V, 60Hz, 85W, Askol M65 design), the pump will function identically to your original. During installation, focus on correct orientation and flapper alignment — the flapper (red) must be positioned so it opens outward toward the drain hose direction to prevent backflow. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (120V AC, 60Hz, 85W, 1.25A), Askol M65 design, red backflow flapper, dimensions, and drain pump function of the original 137221600 used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5221ER1003S Washer Water Valve The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve. Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number. Quick Answer The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order. Common Problems This Part Fixes Washer won't fill with cold water at the start of the cycle Cold water fills much more slowly than it used to Washer keeps filling continuously, even while water is simultaneously draining out Water leaking steadily at the cold water connection point Visible rust or mineral buildup around the valve body or connection Cycle stalling at the fill step and never advancing to wash Water pooling underneath or behind the washer near the cold supply line Cold wash or cold rinse cycles specifically affected while other cycles run fine Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as: LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW LG W3600HVA Kenmore WKE100HVA (select LG-built models) Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure Rated 12V with small male spade terminal connections for a secure electrical fit Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L Direct drop-in replacement — mounts underneath the top panel at the original connection point Replaces 4869496, AP6798394, PS12587936, and EAP12587936 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number 5221ER1003S OEM Part Number 5221ER1003S (also 5221ER1003A) Part Type Washer Water Inlet Valve — Cold Condition Aftermarket Replacement Brand LG Application Front-Load Washers Voltage 12V Electrical Connection Small male spade terminals Color Gray Material Plastic and metal Height 4.75 in. Width 3.25 in. Length 2.25 in. Location Underneath the top panel, dispenser and control panel assembly Quantity 1 valve Compatible Brands LG, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves. Frequently Asked Questions My washer keeps filling even while it's draining. Is that this valve? Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis. Cold water won't fill but hot water works fine. Is this the right part? Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace. I see rust on my old valve but it isn't leaking yet. Should I still replace it? It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later. What's the difference between 5221ER1003S and 5221ER1003A? These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11168743 Washer Water Valve (Hot Side) The XPARTCO W11168743 is an aftermarket replacement hot water inlet valve for Whirlpool-built top-load washers. This is a single-solenoid valve dedicated to the hot water supply — it has one hose fitting inlet and one water outlet, and its only job is to open when the control calls for hot water and close again once the correct fill level is reached. This platform pairs the hot valve with a separate two-solenoid cold valve (sold separately as W11168740), so the hot and cold sides are independent components rather than one combined valve body. Because it's a dedicated single-function valve, a failure here produces a distinctive symptom: hot-only fills stop working or slow down dramatically, while cold fills (governed by the separate cold valve) continue working normally on their own. Common failure causes include mineral or sediment buildup that prevents the valve from sealing fully, a burned-out solenoid coil, or a worn rubber grommet or gasket at the push-on outlet connection. It directly replaces WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, PS12348074, and EAP12348074. Quick Answer The XPARTCO W11168743 Washer Water Valve (Hot Side) fixes Whirlpool-built top-load washers where hot water won't fill, fills slowly, overfills, leaks into the drum when off, or fails to stop filling. Single-solenoid hot-only valve, 120V, 60Hz, standard hose fitting inlet with push-on outlet connection. Replaces WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, PS12348074, EAP12348074. This is the hot-side valve only — the companion cold-side valve is sold separately as W11168740. Common Problems This Part Fixes Washer won't fill with hot water while cold water fills normally Hot water fills much more slowly than it used to Washer overfills or won't stop filling Water leaking or trickling into the drum on the hot side when the washer is off Washer not washing properly due to insufficient hot water reaching the drum Cycle stalling at the fill step and never advancing to wash No hot water reaching the washer despite the water heater and supply line working correctly Water pooling underneath or behind the washer near the hot supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168743, WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, AWP43142, PD00040928, PS12348074, EAP12348074 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including: Whirlpool top-load washers (select models) Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Inglis, Magic Chef, Crosley, Norge, Modern Maid, and Caloric top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note — hot side only, and a different platform than our front-load valves: This is the hot water valve for Whirlpool's top-load platform. The matching cold water valve for these same washers is sold separately under part number W11168740 — the two are not interchangeable. This part is also a different valve family entirely from the front-load W11688994 (hot) / W11688995 (cold) valves elsewhere in our catalog; those fit a different washer platform and will not work here. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve fits your washer. Key Features Aftermarket replacement single-solenoid hot water inlet valve for Whirlpool-built top-load washers Standard hose fitting inlet with a single push-on water outlet and rubber grommet seal Resolves "won't fill with hot water," "fills slowly," "overfills," and "won't stop filling" symptoms caused by valve failure Rated 120V, 60Hz Approximately 3-1/2"L x 3-1/2"W x 2-1/4" deep Direct drop-in replacement — no modification required Replaces WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, PS12348074, and EAP12348074 Compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Inglis, Magic Chef, Crosley, Roper, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW11168743 OEM Part Number W11168743 Part Type Washer Water Inlet Valve — Hot Side Condition Aftermarket Replacement Application Top-Load Washers (Whirlpool-Built) Voltage 120V Frequency 60 Hz Solenoids 1 (dedicated hot water function) Inlet Connection Standard hose fitting Outlet Connection Push-on with rubber grommet Dimensions Approx. 3-1/2"L x 3-1/2"W x 2-1/4" deep Companion Part W11168740 (cold water valve, sold separately) Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Inglis, Magic Chef, Crosley, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the hot water supply hose from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit next to each other and it's easy to cross a wire. Disconnect the electrical connector from the old hot valve, disconnect the push-on outlet hose (check the rubber grommet for wear and replace it if it looks flattened or cracked), remove the mounting screw or bracket, and pull the valve free — leave the cold valve (W11168740) undisturbed if it isn't also being replaced. Install the new W11168743 in the same position, secure the mounting screw, reconnect the electrical connector, and press the outlet hose back onto its fitting with the grommet properly seated. Reattach the hot water supply hose, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm hot water fills at the normal rate with no leaking underneath or behind the washer. Tools needed: Phillips screwdriver, nut driver, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Hot water won't fill but cold water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Since your washer uses separate hot and cold valves rather than one combined valve, a fault on the hot side only affects hot fills while the cold valve keeps working independently. If hot-specific cycles are the ones failing while cold cycles are unaffected, this hot-side valve is the correct part to replace. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that's actually failed. If only hot fills are affected, replacing this W11168743 valve alone is sufficient. Some people choose to replace both while the top panel is already off, especially on an older washer, but it isn't required. Is this the same valve used on your front-load washer listings? No. This valve is built for Whirlpool's top-load platform. The front-load hot/cold valve pair in our catalog (W11688994 and W11688995) is a completely different part family for a different washer design, and the two are not interchangeable. Always check whether your washer is a top-load or front-load model, and verify your exact model number, before ordering either. My washer has no hot water at all, but the water heater is working. What should I check first? Before assuming the valve has failed, confirm the hot water supply valve at the wall behind the washer is fully open, check the inlet screen inside the valve port for sediment or debris that could be restricting flow, and make sure the hot supply hose isn't kinked. If those check out and hot water still isn't reaching the drum, the valve itself is the likely cause. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the single-solenoid design, connection type, and dimensions of the original W11168743 hot water valve used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Inglis, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

280187 Washer Genuine OEM Drain Pump Assembly 120V, 60 Hz, 0.70 W. Fits specific Whirlpool Duet/H3 front load washers. Replaces Part Numbers: 280187, 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, EA1485610, PS1485610. Description: The Drain Pump is a Genuine OEM part for select Whirlpool made washing machine models that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster. 

Read more less