Search results for "Range Surface"

WB31M19CM 8" Porcelain Drip Pan Porcelain drip bowl (also called a drip pan) for 8 inch burner on an electric range. The drip pan sits underneath the heating element to collect drips or spills around the burner. 8" Porcelain pan. Fits GE, Hotpoint range. Replaces Part Numbers: WB31M19, WB32X5069, WB31M0019, AH244373, EA244373, AP2028043, PS244373.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO MEE61841401 Gas Oven Igniter The XPARTCO MEE61841401 is an aftermarket replacement oven burner igniter compatible with select LG and Kenmore gas ranges in the LDG, LRG, LSG, LSS, LTG, and LSR series. The igniter is a flat glow bar hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without ever lighting the burner. This igniter draws 3.3–3.8 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F within approximately 60 seconds. The igniter body measures 3-1/2 inches long x 1-3/4 inches wide x 7/8 inches high, with a lead/plug assembly extending approximately 10-3/4 inches from the igniter. It includes a 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors to accommodate direct plug-in or spliced installation. Directly replaces OEM part numbers MEE61841401, MEE61841403, and MEE63084901. Quick Answer The XPARTCO MEE61841401 Gas Oven Igniter fixes LG and Kenmore gas ovens that won't heat, take too long to preheat, display error codes F9 or F11, or have an igniter that glows but never lights the burner. Flat glow bar style, silicon carbide. Draws 3.3–3.8A at 120V. Igniter body 3-1/2" L x 1-3/4" W x 7/8" H with 10-3/4" lead. Includes bracket and 2 porcelain wire connectors. Replaces MEE61841403 and MEE63084901. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat Igniter glows orange or red but never lights the gas burner Error codes F9 or F11 displayed on LG gas ranges Gas smell when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Igniter burned out or visibly cracked or broken Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: MEE61841401, MEE63084901, 1599783, MEE61841403, EAP3535362, ALG1385007, PD00001851, 095225468650, AH3535362, EA3535362, AP5214765, PS3535362. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This igniter is compatible with select gas ranges from the following brands and series: LG gas ranges — LRG series (freestanding) LG gas ranges — LDG series (freestanding) LG gas ranges — LSG series (slide-in) LG gas ranges — LSS series LG gas ranges — LTG series LG gas ranges — LSR series Kenmore / Sears gas ranges (select LG-built models) Compatible with both single and double oven models. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Flat glow bar hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Silicon carbide construction — superior heat resistance, high melting point, corrosion and oxidation resistant Draws 3.3–3.8 amps at 120V AC — correct amperage range to open the LG gas safety valve Operating temperature: 1,800°F – 3,100°F with approximately 60-second heat-up time Igniter body: 3-1/2" L x 1-3/4" W x 7/8" H; lead/plug assembly: approximately 10-3/4" from igniter body Plug-in installation — includes 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors for splicing if needed Compatible with single and double oven models Directly replaces MEE61841401, MEE61841403, and MEE63084901 — no modification required in most cases Resolves error codes F9 and F11 on compatible LG gas ranges Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–20 minutes with basic hand tools Product Specifications Part Number MEE61841401 Also Replaces MEE61841403, MEE63084901 Part Type Gas Oven Burner Igniter (Flat Glow Bar Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (single and double oven) Igniter Style Flat glow bar, cageless Material Silicon Carbide / Metal / Ceramic / Porcelain / Plastic Colors White / Black / Gray Amperage Draw 3.3 – 3.8 Amps Voltage 120V AC Operating Temperature 1,800°F – 3,100°F Heat-Up Time Approximately 60 seconds Igniter Body Dimensions 3-1/2" L x 1-3/4" W x 7/8" H Lead / Plug Length Approximately 10-3/4 inches from igniter body Includes Igniter, mounting bracket, 2-wire harness/plug, 2 porcelain wire connectors Error Codes Resolved F9, F11 Compatible Brands LG, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to contamination. Do not touch the ceramic bar with bare hands under any circumstances — oils from skin will damage the element and significantly shorten its lifespan. Handle only by the bracket, wires, and plug. To install: unplug the range and shut off the gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector. Secure the new MEE61841401 igniter to the burner bracket with the mounting screws. If the plug is a direct match to your range's harness, plug it in. If not, cut the wires and use the included porcelain wire connectors to splice the new igniter to the existing wiring. Reinstall the oven bottom panel, restore gas supply and power, and run a test cycle. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the difference between MEE61841401, MEE61841403, and MEE63084901? These are all part numbers for the same LG flat glow bar oven igniter used across different model ranges and production runs. MEE63084901 is the earlier part number; MEE61841401 and MEE61841403 are updated versions. All three are interchangeable, and this aftermarket replacement is compatible with all of them. How do I know if my oven igniter needs to be replaced? The most common signs are the oven not heating at all, taking much longer than normal to preheat, or the igniter glowing orange but never lighting the gas burner. A healthy igniter glows bright orange and ignites the burner within about 60 seconds. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Error codes F9 or F11 on LG ranges can also indicate a failed igniter. Do I need to splice the wires or does it plug straight in? This igniter includes a 2-wire harness/plug for direct plug-in installation on most compatible LG models. If the connector does not match your range's existing harness, cut the old connector off and use the 2 porcelain wire connectors included in the kit to splice the new igniter to the existing wiring. Do not use standard plastic wire nuts — only porcelain connectors should be used near the oven burner due to the high heat involved. What do error codes F9 and F11 mean on an LG range? On compatible LG gas ranges, error code F9 typically indicates an oven heating failure, and F11 can indicate a shorted or failed igniter circuit. Both codes can be triggered by a weak or failed oven igniter. Replacing the MEE61841401 igniter resolves these error codes in many cases — though other causes such as a failed gas safety valve or control board issue should also be ruled out if the problem persists after replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from silicon carbide, metal, ceramic, and porcelain to match the electrical specifications and physical dimensions of the original MEE61841401 igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO AEZ73293801 Cooktop Burner Control Knob – Compatible with LG & Kenmore Cooktops Product Description Restore smooth, precise burner control with the XPARTCO AEZ73293801 Cooktop Burner Control Knob. This high-quality aftermarket replacement knob fits securely onto the burner control shaft, allowing accurate flame adjustment and dependable operation. A cracked, loose, or missing knob can make it difficult to control heat or safely operate your cooktop. Replacing it with this durable XPARTCO knob restores proper functionality and everyday cooking convenience. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers AEZ73293801, EBZ60710601, 2025031, PD00055975, EAP3639420, AH3639420, EA3639420, AP5594929, PS3639420. Compatibility This replacement cooktop burner control knob fits select LG and Kenmore (LG-manufactured) gas cooktops and ranges. Commonly used on surface burner controls. Always verify your appliance’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches original fit and appearance 🎛️ Smooth Flame Control – Restores accurate burner adjustment 🧩 Direct-Fit Design – Push-on installation for secure seating 💪 Durable Plastic Construction – Built for daily kitchen use 💰 Cost-Effective Repair – Affordable alternative to OEM knobs 📐 Product Specification Part Number: AEZ73293801 Component Type: Cooktop Burner Control Knob Material: High-strength molded plastic Color: Black (OEM-style) Mounting: Push-on / shaft-fit Application: Gas cooktop or range burner control Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: None ⚠️ Safety First: Ensure the cooktop or range is turned off and cool before installing the knob. Basic Steps: Turn the burner control to the OFF position. Align the new XPARTCO AEZ73293801 knob with the control shaft. Press firmly until fully seated. Rotate to confirm smooth operation. ⏱️ Time Required: Under 2 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe, precise burner control in seconds — Add to Cart Now for a quick, budget-friendly fix!

Read more less

XPARTCO 134719300 Dryer Drum Belt The XPARTCO 134719300 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. The drum belt is a critical component that connects the motor pulley to the drum, enabling the drum to rotate during drying cycles. The belt wraps around the drum circumference, passes over an idler pulley (which maintains tension), and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail due to normal wear from friction and heat, cracking or fraying from age and repeated flexing, stretching that reduces tension and causes slipping, contamination from lint buildup, or sudden breakage from overloading or mechanical stress. Constructed from durable black rubber with reinforced fabric or cord embedded inside for strength and flexibility, designed to withstand thousands of hours of operation under high temperatures and constant friction. Dimensions: 90"L x 5/16"W x 1/8"H with 5 ribs and 4 grooves. It directly replaces 134719300, 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294. Important: install the belt with the grooves facing DOWN, against the drum. Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair since both wear together. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 134719300 Dryer Drum Belt fixes Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, the dryer makes loud squealing or squeaking noises, or clothes take too long to dry. 90"L x 5/16"W x 1/8"H. 5 ribs, 4 grooves. Black rubber. Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, PS2349294. Install with grooves facing DOWN against the drum. Often paired with idler pulley (134793500/134793511, sold separately). Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Dryer won't start — belt switch (on some models) tripped by broken belt Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — clear sign the belt has snapped Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: 134719300, 137315300, 7134719300, AFR14405, AP4368788, EAP2349294, LB5300, PD00000843, PS2349294. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Frigidaire dryers (select electric and gas models) — including FDEB34RGS1/GS2, FDEB55RGS0/GS1, FDER436RHS0 and related models Electrolux dryers (select models) Crosley dryers — CDE4500KW0, CDE4700LB0/LW0, CDE4701QW0, CDE7300RW0, CDE7400QW0/QW1, CDE7500KB0/KR0/KW0, CDE7700LR0/LW0, CDEC450KW0, CDEC750KW0, CDG4500KW0, CDG4700LB0/LW0, CDG4701QW0, CDG7300RW0/RW1, CDG7400QW0, CDG7500KB0/KR0/KW0, CDG7700LW0/LW1 series Kenmore / Sears dryers — select Frigidaire/Electrolux-built models White-Westinghouse dryers (select models) Gibson dryers (select models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler pulley (134793500 or 134793511, sold separately) — it wears from the same friction cycles as the belt, and if it's rough, seized, or noisy, the new belt will wear out prematurely. Many customers replace both together as a matched set. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction with reinforced fabric/cord for strength and flexibility Engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 90" L x 5/16" W x 1/8" H with 5 ribs and 4 grooves Install with grooves facing DOWN against the drum for proper engagement Replaces 137315300, 7134719300, LB5300, 1482960, AP4368788, EAP2349294, PD00000843, and PS2349294 Compatible with Frigidaire, Electrolux, Crosley (CDE/CDG series), Kenmore, White-Westinghouse, and Gibson dryers Often replaced together with the idler pulley (134793500/134793511, sold separately) as a paired repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP134719300 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Frigidaire/Electrolux platform) Length 90" Width 5/16" Thickness 1/8" Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber with reinforced fabric/cord Installation Orientation Grooves face DOWN against the drum Often Paired With Idler Pulley (134793500 or 134793511, sold separately) Compatible Brands Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, Gibson Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooves Face DOWN Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Remove the top and/or front panels of the dryer to access the drum — the specific procedure varies by model, but typically involves removing 2–4 screws under the top edge or lint trap area, then lifting or tilting the top panel forward. Once the top is off, disconnect the door switch wire harness and lift the front panel free. This exposes the drum, motor, and idler pulley. Photograph the belt routing before disassembly if any belt fragments remain — you'll need to match the routing pattern with the new belt. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley. Support the drum from underneath (a wooden block or two can help hold it in position). Route the new 134719300 belt around the drum in the same position as the old belt — approximately 4-6 inches from the front lip of the drum. Install with the grooves facing DOWN, against the drum surface — this is essential for proper engagement with the motor pulley. From under the drum, route the belt over the idler pulley and around the drive motor pulley in a Z-shape. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly. Verify the drum rotates freely without binding — if it doesn't, the belt is twisted, kinked, or misrouted; fix it before reassembling. Reinstall the front and top panels, reconnect the door switch, restore power, and run a test cycle to confirm normal operation. Tools needed: Phillips screwdriver, wooden block, side cutters (for removing broken belt fragments), flathead screwdriver, work gloves. Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming/whirring) but the drum stays still, the belt has almost always snapped or is slipping badly. To confirm without opening the dryer: reach in through the door and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum bearings or rollers could be the issue. In either case, opening the dryer to inspect the belt visually is the definitive check — a snapped belt will be lying in the bottom of the cabinet. Why do I have to install the belt with grooves facing down? The dryer's motor pulley is a smooth, un-grooved cylinder — the belt runs against it with the flat (smooth) side. The drum, on the other hand, needs the grooves to positively engage and drive without slipping under load. So the grooved side faces the drum (down when you're routing the belt around the drum from above), and the smooth side wraps around the motor pulley and idler pulley. Installing the belt backwards with grooves facing up will cause the belt to slip against the drum immediately and can burn out the new belt within a few minutes of operation. Should I replace the idler pulley at the same time? Yes, it's strongly recommended. The idler pulley (134793500 or 134793511 on many compatible dryers) maintains constant tension on the drum belt as the drum rotates. It wears from the same friction cycles as the belt — when the belt fails, the idler pulley bearings have typically also been stressed and are near end-of-life. Since the dryer is already open and the pulley is right there next to the belt, replacing both saves you a repeat repair when the pulley fails a few months later. Signs of a worn idler pulley: rough or noisy rotation when spun by hand, visible wear grooves, or seized bearings. What's the difference between 134719300 and 137315300? These are the same drive belt across production revisions. 137315300 was a Frigidaire OEM part number and 134719300 is the current cross-referenced part number that covers the same belt. Both are physically and functionally identical — if your dryer's parts diagram shows either number, this listing is the correct replacement. LB5300 and 7134719300 are additional catalog references for the same belt. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable rubber with reinforced fabric/cord to match the dimensions (90"L x 5/16"W x 1/8"H), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original 134719300 drum belt used in compatible Frigidaire, Electrolux, Crosley, Kenmore, White-Westinghouse, and Gibson dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304509706 Gas Oven Igniter Product Overview The XPARTCO 5304509706 Gas Oven Igniter is designed to ignite the gas burner and ensure consistent oven heating performance. This Oven Igniter is a replacement part for select Frigidaire, Kenmore, GE gas oven models, designed to ignite the gas in the oven burner to start the heating process. This part is responsible for creating the spark that ignites the gas, providing the heat needed to cook and bake food. Over time, the oven igniter can wear out or become damaged, which can prevent the oven from heating. Quick Answer If your gas oven is not heating, takes too long to preheat, or the burner does not ignite, the 5304509706 igniter may be weak or faulty. Replacing this igniter restores proper ignition and consistent oven performance. Replaces Part Numbers Replaces OEM part number: 5304509706, 316489402, 316489408, 316119301, 4545981, 012505482182, EAP12071409, AFR18015, PD00035904, AP6230715, PS12071409, WB2X10016, WB02X10016, 1704, EAP241804, AGE826644, PD00042950, AH241804, EA241804, AP2009619, PS241804. Compatibility This gas oven igniter is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible gas ranges and ovens. Frigidaire Gas Ranges Electrolux Ovens GE Gas Ranges Kenmore Gas Ovens Always verify your appliance model number before ordering. Common Problems This Part Fixes Oven not heating Slow or delayed ignition Burner not lighting Gas smell due to ignition failure Key Features Designed for gas oven ignition Provides fast and reliable burner ignition High-quality aftermarket replacement Durable construction for long-lasting performance Product Specifications Part Number: XP5304509706 Part Type: Gas Oven Igniter Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Gas Ovens & Ranges Troubleshooting Guide Oven not igniting → Faulty igniter Long preheat time → Weak igniter No flame despite gas flow → Igniter failure When Should You Replace This Igniter? Replace this igniter if your oven fails to heat, takes too long to preheat, or does not ignite the gas burner properly. Installation Notes ⚠️ Disconnect power and shut off gas before installation. Remove mounting screws, disconnect wiring, and install the new igniter carefully. Avoid touching the igniter surface with bare hands. Related Parts Gas Oven Safety Valve Oven Temperature Sensor Control Board Frequently Asked Questions Will this igniter fit my oven?This igniter fits many Frigidaire and compatible gas ovens. Always verify your model number. What does an oven igniter do?It ignites the gas burner and allows the oven to heat properly. What are signs of a bad igniter?Oven not heating, delayed ignition, or no flame during operation. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO W11590294 Gas Oven Igniter The XPARTCO W11590294 is an aftermarket replacement flat-style silicon carbide gas oven igniter compatible with select Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges in the WFG, AGR, VRGW, and related series. The oven igniter is a silicon carbide heating element mounted next to the oven burner tube. When a bake or broil cycle is started, the igniter draws electrical current through the gas safety valve, which holds the valve open — and simultaneously heats to ignition temperature to light the gas. The igniter must draw at least 3.2 amps to hold the gas valve fully open; as the silicon carbide element ages and weakens, it draws progressively less current, causing the oven to take too long to light, not light at all, or glow without ever opening the gas valve. This flat-style igniter is rated 3.3–3.6 amps at 120V and measures approximately 4" wide x 1" high. It features a silicon carbide element, high-temperature ceramic housing, and metal bracket. The current part number W11590294 directly supersedes W11208965, W11613927, and W11506321 — all four are the same igniter across successive production revisions. It also replaces 4977065, AP7193166, PS16744629, and EAP16744629. Pre-attached wire connectors included. Note: do not touch the silicon carbide element with bare hands — skin oils cause premature burnout. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W11590294 Gas Oven Igniter fixes Whirlpool-family gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat silicon carbide igniter, 3.3–3.6A, 120V, approx. 4"W x 1"H. Do not touch element with bare hands. Replaces W11208965, W11613927, W11506321, 4977065, AP7193166, PS16744629. Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and more. Common Problems This Part Fixes Oven not heating — igniter not reaching operating temperature or gas valve not opening Igniter glows orange or red but the oven burner never lights Oven takes more than 90 seconds to ignite — igniter too weak to fully open the gas valve Oven preheats very slowly — weakened igniter limiting gas valve opening Gas smell when oven is turned on but burner does not light Igniter visibly cracked, broken, or burned out Bake or broil function not working on compatible models Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: W11590294, W11208965, W11506321, W11613927, AP7193166, AWP45526, EAP16744629, PD00083398, PS16744629. W11590294 is the current production part number superseding W11208965, W11613927, and W11506321 — all four are the same igniter. If your parts diagram shows any of these numbers, this replacement is correct. Contact our support team with your model number if you need confirmation before ordering. Compatibility This oven igniter is compatible with select gas ranges and ovens from the following brands and series: Whirlpool gas ranges — WFG320 series (WFG320M0MB0, WFG320M0MS0, WFG320M0MW0 and related models) Whirlpool gas ranges — WFG505 series (WFG505M0BS4, WFG505M0BW3, WFG505M0MB0, WFG505M0MS0, WFG505M0MW0 and related models) Amana gas ranges — AGR4203 series (AGR4203MNB0, AGR4203MNW0 and related models) Amana gas ranges — AGR6303 series (AGR6303MMB0, AGR6303MMW0 and related models) Crosley gas ranges — VRGW series (VRGW3150RB0, VRGW3150RW0, VRGW3162RB0, VRGW3162RS0, VRGW3162RW0 and related models) Maytag gas ranges (select models) KitchenAid gas ranges (select models) Jenn-Air gas ranges (select models) Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the gas safety valve to hold it open so gas can flow to the burner Draws 3.3–3.6 amps at 120V — correct amperage range to reliably open the oven gas safety valve on compatible models Dimensions: approximately 4" wide x 1" high Silicon carbide element, high-temperature ceramic housing, metal mounting bracket Pre-attached wire connectors included — direct plug-in installation on compatible models Current production part superseding W11208965, W11613927, and W11506321 Do not touch the silicon carbide element with bare hands — skin oils cause premature burnout Compatible with Whirlpool WFG320/WFG505, Amana AGR4203/AGR6303, Crosley VRGW, Maytag, KitchenAid, and related brands Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPW11590294 Supersedes W11208965, W11613927, W11506321 Part Type Gas Oven Flat Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens Igniter Style Flat silicon carbide element Amperage Draw 3.3 – 3.6 Amps Voltage 120V AC Dimensions Approximately 4" W x 1" H Material Silicon carbide / Ceramic / Metal / Plastic Color White / Silver Connector Pre-attached wire connectors Handling Note Do not touch element — skin oils cause premature burnout Compatible Brands Whirlpool, Amana, Maytag, KitchenAid, Crosley, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas range. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. ⚠️ Handle With Care — Do Not Touch the Igniter Element The silicon carbide igniter element is fragile and sensitive to skin oils. Handle only by the bracket and wiring — never touch the silicon carbide element itself. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel to expose the burner assembly. Locate the old igniter mounted next to the oven burner tube. Disconnect the igniter's wire connectors and remove the two mounting screws securing the bracket. Note the wire routing inside the range cavity before removing — be careful not to let the burner wires fall back into the range body. Connect the new W11590294 igniter's pre-attached connectors to the matching wires from the range. Mount the new igniter in the same position with the two bracket screws. Reinstall the oven bottom panel and racks. Restore gas and power, then run a bake cycle and confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the relationship between W11590294, W11208965, W11613927, and W11506321? These are all part numbers for the same gas oven igniter across successive production revisions by Whirlpool. W11506321 was an earlier version, W11613927 and W11208965 were subsequent updates, and W11590294 is the current production number. All four are the same flat silicon carbide igniter with the same specifications, dimensions, and function. If your range's parts diagram or old igniter shows any of these numbers, this replacement covers all of them. My oven igniter glows but the burner never lights — is this the right part? Yes — an igniter that glows but fails to light the burner is the most common symptom of a weakened igniter. The gas safety valve requires at least 3.2 amps of current draw through the igniter to hold it open. As the silicon carbide element ages, it draws less current — eventually reaching a point where it glows visibly but no longer draws enough current to fully open the gas valve. If the igniter glows for more than 90 seconds without the burner lighting, it needs replacement. The W11590294 is rated 3.3–3.6 amps, which is the correct range to reliably activate the safety valve on compatible models. What is the difference between W11590294 and W11176454? Both are flat silicon carbide oven igniters for Whirlpool-family gas ranges, but for different model series. The W11590294 is used on the WFG320, WFG505, and related entry-level Whirlpool and Amana gas ranges. The W11176454 (which replaces W10914411) is used on higher-end Whirlpool, Amana, and Maytag models across a broader range of WFG, MGR, and related series. They have the same amperage rating and igniter style but are not always interchangeable — always verify your model number before ordering to confirm which igniter is correct for your range. How do I test if the oven igniter has failed? The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, the igniter is too weak. For a more precise test, use a multimeter in resistance mode — disconnect the igniter and measure resistance across the element. A working W11590294-style igniter typically reads between 40–100 ohms at room temperature. An open circuit (infinite resistance) means the element has burned through completely. You can also test in operation by measuring current draw at the igniter circuit — a reading below 3.2 amps indicates the igniter is too weak to reliably open the gas valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original W11590294 gas oven igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO Y312959 Dryer Drum Belt Replaces WPY312959 The XPARTCO Y312959 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers — including the long-running vintage Maytag DE and DG halo-of-heat series. The drum belt is a critical component that connects the drive motor to the drum. It wraps all the way around the drum's circumference, passes around a spring-loaded idler (tension) pulley, and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail from normal wear, cracking or fraying from age and repeated flexing, exposure to heat and lint buildup, stretching that causes slipping, or sudden breakage. Constructed from durable black rubber. Dimensions: 100" long x 3/8" (5/16") wide, with 5 ribs and 4 grooves. Includes instructions. It directly replaces Y312959, WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PD00028571, and PS11757542. Important: install the belt with the grooved side against the motor pulley and the smooth side against the drum. Because the belt is symmetrical, it can be installed with either end facing out. Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO Y312959 Dryer Drum Belt fixes Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, or the dryer makes loud squealing/thumping noises. 100"L x 3/8"W. 5 ribs, 4 grooves. Black rubber. Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PS11757542. Install grooved side against the motor pulley, smooth side against the drum. Often paired with idler pulley WP6-3037050 and drum roller kit 12001541. Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — a clear sign the belt has snapped Belt worn thin or stretched after decades of use on a vintage Maytag dryer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: Y312959, WPY312959, 1000H5, 1246110, 3-12959, 3-14774, 312959, 314774, 8195-959, P46-150, P46-151, 6 3129590, AP6024192, AWP51437, EAP11757542, PD00028571, PS11757542 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Maytag electric dryers — DE106, DE107, DE110, DE180, DE18CA/CM/CS/CT, DE19CA/CD/CS/CT, DE210, DE212, DE21CA/CM/CS/CT, DE22CA/CS/CT, DE23CD, DE24CA/CM/CS/CT, DE25CS, DE26CA/CD/CS/CT, DE27CA/CS/CT, DE303, DE308, DE309, DE312, DE313, DE382, DE4000, DE408-DE9900 series and many more Maytag gas dryers — DG106, DG107, DG110, DG18CA/CM/CS/CT, DG19CA/CD/CS/CT, DG210, DG212, DG21CA/CM/CS/CT, DG22CA/CS and related DG-series models Maytag dryers — LDE and LDG series (LDE7304ACE, LDE8406ACE/ACM/ADE, LDE8410, LDG8424AAE, LDG9304AAM and related) Jenn-Air dryers (select models) Whirlpool dryers (select Whirlpool-built models) Amana, Magic Chef, Admiral, Norge, Roper dryers (select Whirlpool/Maytag-built models) Kenmore / Sears dryers (select Whirlpool/Maytag-built models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler (tension) pulley (WP6-3037050) and the drum support rollers (kit 12001541 / 303373K) — they wear from the same friction cycles as the belt, and if they're rough, seized, or noisy, the new belt will wear out prematurely. Before replacing the belt due to noise, check the drum support rollers and idler pulley and replace if you see signs of wear. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction — engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 100" long x 3/8" (5/16") wide with 5 ribs and 4 grooves Install with the grooved side against the motor pulley and the smooth side against the drum Symmetrical design — can be installed with either end facing out Includes instructions Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, and PS11757542 Compatible with vintage Maytag DE/DG series, LDE/LDG series, plus Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number Y312959 OEM Part Number WPY312959 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Maytag / Whirlpool platform) Length 100" Width 3/8" (5/16") Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber Installation Orientation Grooved side against motor pulley, smooth side against drum Often Paired With Idler Pulley (WP6-3037050), Drum Roller Kit (12001541 / 303373K) Compatible Brands Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooved Side Against Motor Pulley Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Access the drum by removing the appropriate panels — the specific procedure varies by model, but on many vintage Maytag dryers this involves removing the front or top panel. Photograph the belt routing before disassembly if any belt fragments remain. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley, and vacuum out accumulated lint and belt dust. Clean any belt dust off the drum. Route the new Y312959 belt around the drum. Install with the grooved (ribbed) side against the motor pulley and the smooth side against the drum — this is the correct orientation for proper drive engagement. Because the belt is symmetrical, either end can face outward. A helpful tip from experienced installers: use two small pieces of tape to hold the belt against the drum while you lace it onto the idler and motor pulleys. From under or behind the drum, route the belt around the idler (tension) pulley and the drive motor pulley following the belt diagram for your model. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly without binding. While you have the machine apart, check that the idler pulley and drum support rollers spin freely — if they're rough or noisy, replace them now to protect the new belt. Reassemble the panels, restore power, and run a test cycle. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, vacuum, work gloves, tape (helpful for holding the belt). Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming) but the drum stays still, the belt has almost always snapped. To confirm without opening the dryer: reach in and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum rollers or bearings could be the issue. Opening the dryer to inspect is the definitive check — a snapped belt will be lying in the bottom of the cabinet. On decades-old Maytag dryers, a belt that finally snapped from age is one of the most common repairs. Which way does the belt go — grooves in or out? Install the belt with the grooved (ribbed) side facing the motor pulley and the smooth side against the drum. The ribs engage the grooved motor pulley for positive drive without slipping, while the smooth side rides against the large drum surface. Note that this is the opposite orientation from some other dryer belts (like certain Frigidaire belts where grooves face the drum) — so don't assume; follow the grooves-against-motor-pulley rule for this Maytag/Whirlpool-platform belt. The belt is symmetrical end-to-end, so either end can face outward; only the grooved-vs-smooth orientation matters. Should I replace the idler pulley and drum rollers at the same time? It's strongly recommended, especially on older dryers. The idler (tension) pulley (WP6-3037050) keeps the belt under proper tension, and the drum support rollers (kit 12001541 / 303373K) carry the drum's weight as it turns. All wear from the same friction and heat cycles as the belt. In fact, a common piece of repair advice is: before you replace the belt due to noise, check the drum support rollers and idler pulley first — worn rollers or a seized idler are frequent noise sources, and if you replace only the belt, the new belt may wear out prematurely against a bad pulley. Since the dryer is already apart, replacing all three together is efficient and saves a repeat repair. What's the difference between Y312959 and WPY312959? These are the same drum belt across production revisions. Y312959 was the earlier Maytag part number and WPY312959 is the Whirlpool-era part number (after Whirlpool acquired Maytag) for the same belt. WPY312959VP is a variant packaging code. All are physically and functionally identical — if your dryer's parts diagram shows any of these numbers, this listing is the correct replacement. The many other cross-references (3-12959, 314774, LB234, P46-150, etc.) reflect the belt's long production history across decades of Maytag dryers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag/Whirlpool OEM part, but is manufactured from durable rubber to match the dimensions (100"L x 3/8"W), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original Y312959/WPY312959 drum belt used in compatible Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 22003483 Washer Drive Belt The XPARTCO 22003483 is an aftermarket replacement drive belt for Whirlpool-built Maytag Atlantis top-load washers. This belt is the mechanical link between the drive motor and the washer's drive system — it's what actually transmits the motor's rotation to spin the drum, so both agitation and spin depend entirely on this belt gripping its pulleys correctly and staying properly tensioned. Made of black rubber, this belt measures 52 inches long. Over years of use, the belt material gradually hardens and glazes over, becoming smooth and "slick" rather than gripping the pulleys firmly — this degradation can cause the belt to slip under load even before it shows any visible cracking or damage. A worn belt produces a range of symptoms depending on how far the wear has progressed: the washer may pump water but fail to spin, fail to agitate at all, spin noticeably slower than normal, or produce a chirping or slipping noise, especially as the motor shifts between wash and spin modes. It directly replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667. Quick Answer The XPARTCO 22003483 Washer Drive Belt fixes Maytag (Whirlpool-built) top-load washers that pump but won't spin, won't agitate, spin slowly, or make a chirping/slipping noise as the motor shifts modes. 52 inches long, black rubber. Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, 824667. A belt can slip and cause symptoms well before it looks visibly worn — years of use leave the rubber "slick" and unable to grip the pulleys properly, even without visible cracking. Common Problems This Part Fixes Washer pumps water but won't spin Washer won't agitate Washer spins noticeably slower than it used to Chirping or slipping noise, especially as the motor shifts between wash and spin modes Belt that has become glazed, hardened, or "slick" from years of use Visible cracking, fraying, or glazing on the belt surface General noise or vibration during the wash or spin cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP22003483 22003483, 22002709, 62618130, 824667, AP6006365, EAP11739438, WP22003483VP, AWP47150, PD00002551, PS11739438 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Maytag Atlantis top-load washers built on the Whirlpool platform, including model numbers such as: MAV4057AWQ, MAV4057AWW, MAV4500AWW MAV5000AWQ, MAV5000AWW, MAV5057AWQ, MAV5057AWW, MAV5960AWW MAV6000AWQ, MAV6000AWW, MAV6057AWQ, MAV6057AWW MAV6200AWQ, MAV6200AWW, MAV6250AWQ, MAV6250AWW, MAV6257AWQ, MAV6257AWW MAV6548AWQ, MAV6548AWW, MAV6601AWQ, MAV6601AWW, MAV6650AWW, MAV7000AWQ Note: Always verify your full model number before ordering, since Whirlpool and Maytag use different belt lengths and profiles across their washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drive belt — transmits motor power to spin the washer drum Resolves "pumps but won't spin," "won't agitate," "spins slowly," and "chirping/slipping noise" symptoms caused by belt wear 52 inches long, black rubber construction Rides on three pulleys to transfer motor rotation to the drive system Direct drop-in replacement matching the original length and profile Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667 Compatible with Maytag Atlantis top-load washers built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 22003483 OEM Part Number WP22003483 Part Type Washer Drive Belt Condition Aftermarket Replacement Application Maytag Atlantis Top-Load Washers (Whirlpool-Built) Length 52 inches Material Rubber Color Black Function Transmits motor rotation to the drive system to spin the drum Quantity 1 drive belt Compatible Brand Maytag (Whirlpool-built) Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the motor and belt area. Loosen the motor's mounting screws so the motor can be pushed toward the drum, releasing tension on the old belt. Slide the old belt off its three pulleys and remove it. Route the new 22003483 belt over the same three pulleys, matching the original path. With the belt in place, gently push the motor away from the drum by hand to apply tension, then tighten the motor's mounting screws while continuing to check belt tightness — the belt should have firm, even tension across all three pulleys with no excess slack. Reinstall the rear panel, restore power, and run a full test cycle through both agitate and spin to confirm smooth, quiet operation with no chirping or slipping. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions My washer makes a chirping noise when it shifts from agitate to spin. Is that the belt? Yes, this is a documented symptom of a worn belt. One long-term owner traced this exact chirp to a 10-year-old belt that had become "slick" from age — smooth and hardened enough that it briefly slipped on the pulleys as the motor shifted between modes, rather than moving cleanly into position. Replacing the belt resolved the noise completely. My belt doesn't look cracked or damaged. Could it still be the problem? Yes. A belt can degrade in ways that aren't obvious at a glance — the rubber can harden and glaze over time, becoming slick and losing its grip on the pulleys even without visible cracking or fraying. If your washer is slipping, chirping, or spinning weakly and the belt has been in service for many years, age-related slickness is a reasonable explanation even if the belt still looks intact. How do I know if I have the right belt length for my washer? This belt is 52 inches long and specific to the Maytag Atlantis top-load platform. Whirlpool and Maytag use different belt lengths across other washer models, so always confirm your model number matches the compatibility list, or measure your old belt for comparison, before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, profile, and material of the original WP22003483 drive belt used in compatible Maytag Atlantis top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO H150 Furnace Silicon Nitride Rod Ignitor The H150 universal gas furnace igniter come with a 1.95-inch ceramic nitride heating element, a 1.25-inch ceramic insulator, a 304 stainless steel bracket, and a 15.5-inch high temperature resistant wire(20 AWG). Voltage: 120V±10%-15%, 50/60HZ. Power Rating: 150W. Cold resistance: 9-17Ω. At 120V furnace igniter H150 can reach 1200 degrees in a short time The H150 universal furnace igniter replacement can be used in a wide range of machines and is the perfect replacement for silicon carbide ignitors in water heater boilers and gas forced-air furnaces, replacing more than 180 types of ignitors and covering nearly 90% of all applications. Such as stoves, furnace, warm air motion, gas ignition, hot surface igniter, infrared light source, pool heater, boiler, etc California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10721967 Washer Drive Clutch Kit The XPARTCO W10721967 is an aftermarket replacement drive clutch kit — often called a "splutch" kit — for Whirlpool-built top-load washers. This assembly sits at the base of the transmission and works together with the mode shift actuator to control how power reaches the washer: during agitation, the clutch engages to drive the washplate back and forth, and during spin, it locks up to spin the inner wash basket at full speed. The name "splutch" comes from what it actually is — part spring, part clutch — and that spring-loaded design is what lets the same assembly smoothly transition between the gentle agitate motion and the much more forceful spin cycle. This is a complete 6-piece kit: spring, clutch housing, cam ring, basket drive gear, drive pulley, and mounting nut, so you're replacing the entire wear-prone assembly at once rather than chasing individual worn components. Over time the clutch's friction surfaces glaze over and wear down, the cam ring's engagement points round off, and the spring loses tension — all of which produce the same telltale complaint: a loud grinding, clicking, or clunking noise during agitation or spin, sometimes alongside a washer that spins weakly, agitates but won't spin, or runs hot and starts to smell from the friction of a slipping clutch. It directly replaces AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10721967VP, W10818965, W11396423, 3319979, and PS10057144. Quick Answer The XPARTCO W10721967 Washer Drive Clutch Kit fixes Whirlpool-built top-load washers with loud grinding, clicking, or clunking noise during agitation or spin, a washer that agitates but won't spin, weak or no spin, an overheating smell, or a drum that doesn't spin the pump properly. Complete 6-piece "splutch" kit — spring, housing, cam ring, basket drive gear, pulley, and nut. Replaces AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10721967VP, W10818965, W11396423, 3319979, PS10057144. Often replaced together with the drive belt, since both wear on a similar schedule and share the same teardown. Common Problems This Part Fixes Loud grinding, clicking, or clunking noise during agitation or spin Washer agitates normally but won't spin, or spins very weakly Drive pump doesn't rotate properly, leading to slow or incomplete draining Washer stops agitating partway through a cycle Washer running unusually hot, sometimes with a burning or odd odor Loud noise specifically when transitioning between agitate and spin Clothes coming out excessively wet because the spin cycle isn't reaching full speed Rattling or looseness felt at the drive pulley when the basket is turned by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive clutch kit directly replaces the following OEM and cross-reference part numbers: W10721967, W10721967VP, AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10818965, W11396423, 3319979, PS10057144, EAP10057144, AWP40988, PD00005593. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive clutch kit is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including: Whirlpool top-load washers — WTW series Maytag top-load washers — MVWC series (select Whirlpool-built models) Kenmore top-load washers — KATW and NTW series (select Whirlpool-built models) Amana top-load washers (select models) Crosley top-load washers (select models) Roper top-load washers (select models) Inglis top-load washers (select models) Verified model numbers include: 1CWTW4705GW0, 1CWTW4705GW1, 1CWTW4705GW2, 1CWTW4815EW0, 1CWTW4815EW1, 1CWTW4815EW2, 1CWTW4815EW3, 1CWTW4840YW2, 1CWTW4845EW0, 1CWTW4845EW1, 1CWTW4845EW2, 1CWTW4845EW3, 2DWTW4740YQ1, 4GWTW1805LW0, 4GWTW1805LW1, 4GWTW1955LW0, 4GWTW1955LW1, 4GWTW3000FW0, 4GWTW3000FW1, 4GWTW4740YQ3, 4GWTW4800YQ3, 4KATW5215FW0, 4KATW5415FW0, 4KMVWC215FW0, 4KMVWC315FW0, 4KMVWC410JW0, 4KMVWC415FW0, 4KMVWC420JW0, 4KMVWC425FW0, 4KMVWC430JW0, 4KMVWC440JW0, 4KNTW3100JW0, 4KNTW3200JW0, 4KNTW3300JW0, 7MWGT4027HW1, WTW5000DW1, and MVWX655DW1. Note: This kit fits Whirlpool's belt-drive top-load washer platform specifically. It is not intended for direct-drive designs that don't use a separate clutch and belt system. Because this drive clutch kit fits an extremely broad range of model years and revisions, always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Complete 6-piece "splutch" kit — spring, clutch housing, cam ring, basket drive gear, drive pulley, and mounting nut Works together with the mode shift actuator to engage agitation and lock up for full-speed spin Resolves "grinding or clicking noise," "won't spin," "agitates but won't spin," and "overheating smell" symptoms caused by clutch wear Replaces the entire wear-prone assembly at once rather than individual components Direct drop-in replacement for the washer transmission's drive pulley and clutch assembly Replaces AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10721967VP, W10818965, W11396423, 3319979, and PS10057144 Compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, Crosley, Roper, and Inglis top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10721967 OEM Part Number W10721967 / AP5951296 Part Type Washer Drive Clutch Kit ("Splutch") Condition Aftermarket Replacement Application Whirlpool-Built Belt-Drive Top-Load Washers Kit Contents Spring, clutch housing, cam ring, basket drive gear, drive pulley, mounting nut Function Engages agitation and locks up for full-speed spin Repair Difficulty Moderate — 30-45 minutes Quantity 1 clutch kit (6 pieces) Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Roper, Inglis Installation Notes ⚠️ Unplug Washer And Shut Off Water Before Starting — Tip Onto Its Back Or Front With Care Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Access is from underneath the washer: remove the inner wash basket first (this typically requires a large basket-hub or spanner tool and applying steady upward pressure to break the basket free from the drive hub), then carefully tip the washer onto its back or front, protecting the top and any control panel with a blanket or padding as you lay it down. Photograph the belt and pulley arrangement before disconnecting anything. Remove the drive belt from the motor pulley, then remove the mounting nut and pull the old clutch/pulley assembly off the transmission shaft — a puller tool can help if it's seized. Install the new W10721967 assembly onto the shaft in the same orientation, torque the mounting nut to the manufacturer's specification, and reinstall the drive belt, checking that it seats correctly in the pulley grooves. Carefully stand the washer back upright, reinstall the wash basket, and reconnect it to the drive hub. Restore water and power, then run a full test cycle through agitate and spin, listening for the grinding or clicking noise that prompted the repair. Tools needed: basket-hub removal tool or spanner wrench, socket set, 13mm socket, 5/16" nut driver, pliers, work gloves, and a helper to assist with tipping the washer. Frequently Asked Questions What does "splutch" mean, and why is it sold as one kit instead of individual parts? "Splutch" is shorthand for spring-clutch — the assembly combines a spring-loaded clutch mechanism with the drive pulley and gear that together control agitation and spin. Whirlpool sells this as a single kit because the individual components wear together and interact closely; replacing just the pulley while leaving a worn cam ring or a fatigued spring in place often means the noise or slipping symptom returns quickly. Replacing the complete kit resolves the failure at its actual source. My washer agitates fine but won't spin. Is this the clutch? It's one of the most common causes of exactly that symptom. The clutch has to lock up firmly to transfer full power into spinning the basket; if its friction surfaces have worn down or glazed over, it can still engage well enough for the lighter agitation motion but slip under the higher torque demand of spin. If you hear grinding or clicking specifically as the washer transitions into spin, that reinforces the clutch as the likely cause. Should I replace the drive belt at the same time? It's worth strongly considering. The belt and clutch wear on a similar schedule and share the same teardown — you're already tipping the washer over and removing the belt to access the clutch, so replacing a belt that's showing wear at the same time saves you from repeating the whole disassembly again in the near future. Inspect the belt for glazing, cracking, or fraying while it's off and replace it if it shows any of those signs. The washer smells hot or burnt. Is that dangerous, and does it point to this part? A worn clutch that's slipping generates friction heat, which can produce a warm, slightly burnt smell — this is a real symptom of clutch wear and not something to ignore, since continued operation in that state accelerates wear on the clutch and can stress the drive motor. If you notice this smell along with weak or absent spin, stop using the washer and address the clutch before running further loads. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the spring tension, cam ring engagement geometry, pulley dimensions, and mounting configuration of the original W10721967 clutch kit used in compatible Whirlpool, Maytag, Kenmore, Amana, Crosley, Roper, and Inglis top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less