W11612327 Dishwasher Genuine Circulation Pump
Circulation pump and motor assembly
Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935.
Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.
W11087376 Dishwasher Genuine OEM Pump and Motor Assembly
Fits specific Whirlpool, Maytag, Kenmore Dishwasher models
Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it.
Replaces Part Numbers:W11087376, W10917114, 4534143, AP6237961, PS12074533.
California Residents only
WARNING: California’s Proposition 65
XPARTCO DD31-00016A Dishwasher Drain Pump Motor
The XPARTCO DD31-00016A is an aftermarket replacement BLDC (brushless DC) drain pump motor for Samsung dishwashers. This motor removes water from the dishwasher tub during the drain phase of the cycle — an impeller mechanism pumps water out through the drain hose, running during the draining phase to ensure a constant, steady flow and help prevent clogs.
Weighs approximately 0.50 lbs, with package dimensions of 4.02" x 3.50" x 3.54". Compatible with 120V and 230V systems. Common causes of failure include worn motor bearings, electrical failure, or debris obstructing the impeller. Symptoms of a failing drain pump motor include water not draining from the tub, standing water left after a cycle, unusual noise during the drain phase, or intermittent draining problems that don't happen every cycle. It directly replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701.
Quick Answer
The XPARTCO DD31-00016A Dishwasher Drain Pump Motor fixes Samsung dishwashers that aren't draining, leave standing water after a cycle, make unusual noise during draining, or have intermittent draining problems. BLDC motor, 120V/230V, ~0.50 lbs. Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, 045900194701. When removing the old motor, you'll need to hold a release tab open while twisting the motor counterclockwise at the same time — this two-handed step trips up a lot of first-time installers.
Common Problems This Part Fixes
Dishwasher not draining water from the tub
Standing water left in the tub after a completed cycle
Unusual noise during the drain phase
Intermittent draining problems that don't occur every cycle
Reduced water circulation and cleaning performance
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
DD31-00016A, 113121, 4000925, AP5917178, ASM773863, EAP9606350, PD00036475, PS9606350
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as DW80R9950QH/AA, DW80B7070UG/AA, DW80R9950MT/AA, DW80B6061UG/AA, DW80R9950QN/AA, DW80B7070US/AA, DW80B6061US/AA, DW80B7071UG/AA, DW80B6060US/AA, DW80B6060UG/AA, DW80BB7070U1/AA, DW80B7070AP/AA, DW80B7071US/AA, DW80R7061UG/AA, DDW24T999BB/DA, DDW24M999UM/DA, DDW24T998US/DA, DDW24M999US/DA, DW60M9990AP, and DW80B6060UG.
Note: This part is not a replacement for any earlier designation — per Samsung's own listing, DD31-00016A is a new part that doesn't supersede another part number. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement BLDC (brushless DC) drain pump motor
Resolves "won't drain," "standing water," "unusual noise," and "intermittent draining" symptoms
Impeller mechanism pumps water out through the drain hose to prevent clogs
Compatible with 120V and 230V systems
Direct drop-in replacement matching the original mounting and connections
Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701
Compatible with Samsung dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
Typical repair takes 30 to 60 minutes
Product Specifications
Part Number
XPDD31-00016A
OEM Part Number
DD31-00016A
Part Type
Dishwasher Drain Pump Motor (BLDC)
Condition
Aftermarket Replacement
Brand
Samsung
Motor Type
Brushless DC (BLDC)
Voltage Compatibility
120V / 230V
Weight
Approx. 0.50 lbs
Package Dimensions
4.02" x 3.50" x 3.54"
Repair Difficulty
Moderate — 30 to 60 minutes
Quantity
1 drain pump motor
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — This Step Needs Two Hands Turn off and unplug the dishwasher for safety, and shut off the water supply before beginning. Wear work gloves. Remove any panels or components blocking access to the motor pump. Disconnect all wiring from the old motor. Removing the old motor requires holding a release tab open while simultaneously twisting the motor counterclockwise — this two-handed step trips up a lot of first-time installers, so take it slowly and make sure the tab stays held open through the full twist. Once free, remove the old motor. Install the new DD31-00016A securely in the same mounting position. Reconnect all wiring according to the original connections. Reinstall any panels or components removed for access. Restore the water supply and power, then run a test cycle to confirm the dishwasher drains completely with no leaks or unusual noise. Tools needed: screwdriver, work gloves.
Frequently Asked Questions
My dishwasher isn't draining. Is this the part I need?
Yes, this is the most direct symptom of a failed drain pump motor. Since this motor is what removes water from the tub during the drain phase, a worn or failed motor can leave standing water behind or prevent the cycle from completing properly.
My dishwasher's drainage problem only happens sometimes. Could this still be the motor?
Yes, this is possible. One customer replaced this exact motor to address an intermittent draining issue, noting it was somewhat of a guess since the problem didn't occur every cycle. Intermittent symptoms can still point to a motor that's beginning to fail rather than one that's failed completely, though it's worth noting the customer wasn't fully certain the replacement resolved their specific issue.
What's the trickiest part of installing this motor?
Removing the old motor requires holding a release tab open while twisting the motor counterclockwise at the same time — a two-handed maneuver that one customer specifically called out as the biggest challenge of the whole repair. Taking it slowly and keeping steady pressure on the tab through the full twist makes this easier.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the motor design, impeller mechanism, and voltage compatibility of the original DD31-00016A drain pump motor used in compatible Samsung dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm
The 5304517203 is a genuine Frigidaire OEM lower spray arm for Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers. Positioned at the bottom of the dishwasher tub, this arm rotates as water is pumped through it, spraying water in all directions through its nozzle openings to clean dishes in the lower rack. It snaps directly into the bottom sump assembly and is essential for proper water distribution during the wash cycle.
Made of durable plastic and metal, finished in gray/blue. Over time, the arm can crack, warp, or wear from general use and repeated exposure to hot water and detergent — high heat exposure in particular is a documented cause of failure. A broken or worn spray arm typically shows up as visible damage on the arm itself, dishes in the lower rack not getting cleaned properly, reduced or uneven water coverage, or the arm having difficulty rotating or getting stuck. It directly replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623
Quick Answer
The 5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm fixes Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers where the lower rack isn't getting cleaned properly, water coverage is reduced or uneven, or the arm won't rotate freely or has visible cracks. Snaps into the bottom sump assembly. Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623. After installing, confirm the arm spins freely by hand and doesn't contact the heating element before running a cycle.
Common Problems This Part Fixes
Dishes in the lower rack not getting cleaned properly
Reduced or uneven water coverage during the wash cycle
Spray arm that won't rotate freely or gets stuck
Visible cracks, warping, or damage on the arm itself
Arm that has come loose or detached from the sump assembly
Clogged nozzle holes reducing water pressure and spray coverage
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher lower spray arm directly replaces the following OEM and cross-reference part numbers:
5304517203, 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This lower spray arm is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers built on the same platform.
Note: Non-genuine versions of this exact part number are sold by several third-party sellers. A customer using a non-genuine version of this spray arm reported it came loose and broke during operation, so confirm you're ordering the genuine Frigidaire part rather than a lower-cost imitation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Frigidaire OEM part — factory-specified nozzle pattern and rotation fit
Snaps directly into the bottom sump assembly for a secure, no-tools installation
Resolves "not cleaning lower rack dishes," "uneven water coverage," and "won't rotate freely" symptoms
Durable plastic and metal construction, gray/blue finish
Approximate dimensions: 16.00" x 3.10" x 3.10" (L x W x H)
Direct drop-in replacement — no modification required
Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623
Compatible with Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
5304517203
Part Type
Dishwasher Lower Spray Arm
Condition
Genuine OEM
Brand
Frigidaire
Location
Bottom of the dishwasher tub, in the lower sump assembly
Material
Plastic and metal
Color
Gray / Blue
Dimensions
Approx. 16.00" x 3.10" x 3.10" (L x W x H)
Repair Difficulty
Very Easy — no tools required
Quantity
1 lower spray arm
Compatible Brands
Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, Kenmore
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Confirm Clearance From The Heating Element Disconnect power to the dishwasher and shut off the water supply before beginning. Wear work gloves. Open the dishwasher and pull out the lower rack, setting it aside. Remove the old lower spray arm by releasing the locking tabs on each side and gently pulling it off the sump assembly. Snap the new 5304517203 spray arm onto the sump assembly in the same position. Before closing everything up, spin the arm gently by hand to confirm it rotates freely and does not make contact with the heating element — a real customer account described a spray arm and its support becoming loose and falling into the tub during use, so it's worth double-checking that the arm is fully and securely seated before running a cycle. Return the lower dish rack to its position and close the dishwasher door. Restore power and water, then run a test cycle to confirm the arm spins smoothly and dishes in the lower rack are getting properly cleaned. Tools needed: none.
Frequently Asked Questions
My dishes in the lower rack aren't getting clean. Is this the part I need?
Yes, this is one of the most common symptoms of a worn or damaged lower spray arm. If the arm is cracked, clogged, or not rotating freely, water can't reach dishes in the lower rack evenly, leaving them dirty even when the upper rack comes out clean.
I've read that a spray arm can come loose during operation. How do I prevent that?
This has been reported, particularly with non-genuine imitation parts under the same number. To help prevent it, make sure the new arm snaps fully and securely onto the sump assembly during installation, and spin it gently by hand to confirm it's seated correctly and rotates without wobbling before running your first cycle with it installed.
Do I need any tools to replace this spray arm?
No. This is a simple snap-in, snap-out repair — release the locking tabs on the old arm to remove it, and press the new one onto the sump assembly until it clicks into place. No tools are required.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original nozzle pattern, dimensions, and sump connection of the lower spray arm originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
(2 Pack) WD12X10304 Genuine GE OEM Rack End Cap Clip
Replaces Part Number: WD12X10304, 1556527, WD12X0344, WD12X344, WD30X97, AH2370502, EA2370502, OEM13454003, AP4484666, PS2370502.
Description: This Rack Slide End Cap is a Genuine OEM part for specific GE dishwasher models. This small but essential component is designed to secure the end of the rack slide rail, preventing the dish racks from sliding off the track or becoming misaligned.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link
The WD14X10009 is a Genuine OEM GE replacement dishwasher hinge arm link compatible with an exceptionally wide range of GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers — it fits over 2,100 models. The hinge arm link is the small plastic connector that joins the door spring to the door hinge arm at the bottom of the dishwasher door. This tiny part carries a big load: it's what allows the spring to counterbalance the weight of the door — especially when the door is open with a fully loaded lower rack resting on it. Without an intact link, the spring can't do its job, and the door drops open under its own weight instead of lowering in a smooth, controlled motion.
The hinge arm link is a small piece of white plastic approximately 1-1/2" long, weighing about 0.01 lbs. It fails from ordinary wear and tear — thousands of open/close cycles gradually stress the plastic until it cracks or snaps. As a Genuine OEM part manufactured by GE to factory specifications, the WD14X10009 directly replaces AP2039321, 270839, AH259336, EA259336, and PS259336. Important: your dishwasher has a door spring and hinge arm link on BOTH the left and right sides. This part is sold individually — if one link has broken from age, the other is the same age and often not far behind, so many customers order two and replace both while the dishwasher is pulled out. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link fixes GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore dishwashers where the door falls open instead of lowering gently, the door won't stay shut or won't latch, the door is hard to open or close, or the door slants when open. Small white plastic link ~1-1/2" long — connects the door spring to the door hinge arm. Genuine OEM. Sold individually. Replaces AP2039321, 270839, AH259336, EA259336, PS259336. Fits 2,100+ GE-platform dishwasher models. There's one link on EACH side of the door — consider ordering two.
Common Problems This Part Fixes
Dishwasher door falls open instead of lowering in a smooth, controlled motion — no counterbalance from the spring
Door drops down hard when opened — link broken, spring disconnected
Door won't stay shut, or opens unexpectedly
Door won't latch or lock properly
Door is difficult to open or close
Door slants or hangs unevenly when open
Hinge arm link visibly cracked, bent, broken, or significantly worn
Broken plastic link found lying on the floor beneath the dishwasher
Door spring disconnected and hanging loose
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher hinge arm link directly replaces the following OEM and cross-reference part numbers:
WD14X10009, AGE24269, AP2039321, 270839, AH259336, EA259336, EAP259336, PD00023035, PS259336
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hinge arm link is compatible with an exceptionally broad range of dishwashers — over 2,100 models across the following brands:
GE dishwashers — the vast majority of GE dishwasher models across many generations
GE Profile dishwashers (including PDW-series models)
Café dishwashers (select models)
GE Monogram dishwashers (select models)
Hotpoint dishwashers (select models)
RCA dishwashers (select GE-built models)
Haier dishwashers (select GE-platform models)
Kenmore / Sears dishwashers (select GE-built models)
Important — There Are TWO Links, One Per Side: Your dishwasher door has a spring and hinge arm link on both the left and right sides. This part is sold individually. Many customers discover the second link only after reinstalling the dishwasher — and since both links are the same age and have seen the same wear, the surviving one often breaks soon after. Consider ordering two and replacing both while the dishwasher is already pulled out. Also inspect the door hinge cable at the same time; if it's frayed, kinked, or bent, replace it too.
Key Features
Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
Hinge arm link — connects the door spring to the door hinge arm, allowing the spring to counterbalance the door's weight
Enables the dishwasher door to open in a smooth, controlled motion rather than dropping open
Supports the door's weight even when the lower rack is fully loaded and resting on the open door
Prevents strain on the door hinges and door misalignment
Small white plastic link, approximately 1-1/2" long, ~0.01 lbs
Sold individually — note there is one link on each side of the door
Replaces AP2039321, 270839, AH259336, EA259336, and PS259336
Fits over 2,100 dishwasher models across GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built lines
Inexpensive fix for a problem that would otherwise cost a service call — many customers report the entire repair takes about 15 minutes
DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
WD14X10009
Part Type
Dishwasher Hinge Arm Link (Door Spring Link)
Condition
Genuine OEM
Application
Dishwashers (GE platform)
Length
Approximately 1-1/2"
Weight
Approximately 0.01 lbs
Color
White
Material
Plastic
Function
Connects the door spring to the door hinge arm
Location
Bottom of the dishwasher door hinge, both left and right sides
Quantity
Sold individually (dishwasher uses TWO — one per side)
Model Coverage
Over 2,100 models
Compatible Brands
GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, Kenmore
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. Remove the screws holding the bottom kick plate (a nut driver works well here) and the anchor screws at the top of the dishwasher that secure it to the countertop. Carefully pull the dishwasher out 8–10 inches from the cabinet to expose the door springs and hinge arm links at the bottom on both sides. (Depending on how the dishwasher is plumbed, you may be able to do this without disconnecting the water supply, drain line, or electrical — pull only as far as the connections allow, and disconnect them only if necessary for access.) Look at the hinge assembly at the bottom of the door: you'll see a steel cable with a hooked end, a spring, and the small white plastic link that ties them together. If the link is broken, it may already be lying on the floor. Remove the old link by disconnecting it from the hinge and spring — if it's cracked but still in place, you can break the remaining pieces free. Install the new WD14X10009: place the hinge arm link into the spring, hook the spring onto the clip, and seat the link into the clip on the hinge arm. Note: on some models the crimped hook opening on the steel cable is tight — if the new link won't slide in easily, a small file can carefully open the hook opening enough to accept it. Check the other side of the door while you're in there — there's a second spring and link, and if it's aged or cracked, replace it now. Push the dishwasher back into place, reinstall the anchor screws and kick plate, restore power and water, and test the door: it should now lower smoothly under spring tension rather than falling open. Tools needed: Nut driver, Phillips screwdriver, small file (occasionally), work gloves.
Frequently Asked Questions
My dishwasher door falls open instead of lowering gently — is this the part?
Almost certainly, yes. The door spring is what counterbalances the door's weight so it lowers in a controlled motion. The hinge arm link is the small plastic piece that connects that spring to the door hinge arm. When the link cracks or snaps, the spring is effectively disconnected — so the door has no counterbalance and drops open under its own weight. This is the classic symptom. To confirm, pull the dishwasher out a few inches and look at the bottom hinge area on each side: if a link is broken, you'll often find the pieces on the floor or the spring hanging loose. If both links are intact, check the door hinge cable for fraying or the spring for damage.
Should I order one or two?
Order two. Your dishwasher has a door spring and hinge arm link on both sides of the door — and this part is sold individually. Many customers order one, replace the broken link, push the dishwasher back into the cabinet, and only then realize the second link exists (and is the same age, with the same wear). Since the tedious part of the job is pulling the dishwasher out from under the counter, replacing both links while you're already in there is the smart move. At a few dollars each, having a spare on hand is cheap insurance against doing the whole job over in a few months.
Why do these little plastic links break?
Ordinary wear and tear. The hinge arm link is a small plastic component that carries a surprising amount of load — every time you open the door, it transmits the spring's counterbalancing force to the hinge arm, and that load increases dramatically when the lower rack is fully loaded and resting on the open door. Over thousands of open/close cycles across years of use, the plastic fatigues and eventually cracks or snaps. It's a consumable wear item on GE dishwashers, which is exactly why GE uses the same inexpensive part across 2,100+ models.
Do I have to disconnect the water and electrical to pull the dishwasher out?
Often not. Many customers find that removing the top anchor screws and the bottom kick plate, then sliding the dishwasher out 8–10 inches, gives enough access to reach the hinge arm links — without disconnecting the water supply, drain hose, or electrical. It depends on how much slack your installer left in those lines. Pull the dishwasher out only as far as the connections allow, and see whether you can reach the hinge area. If the lines are too short and you can't reach, you'll need to disconnect the water supply, drain tube, and electrical (turn off power and water first). Either way, the link replacement itself takes only a few minutes once you can reach it.
Should I replace the door hinge cable at the same time?
Inspect it, and replace it if it shows any damage. The door hinge cable is the steel cable that connects the door spring assembly to the door hinge — it works alongside the link and spring in the same counterbalance system. If the cable is frayed, kinked, bent, or its crimped hook end is damaged, it will fail soon and you'll be pulling the dishwasher out again. Since you already have access, this is the ideal moment to check it. Also inspect the door spring itself for stretching or breakage. Contact our support team with your model number if you need the correct cable or spring part number.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same hinge arm link installed in compatible GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WD19X25278 Dishwasher Diverter Assembly
The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning.
The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK.
Quick Answer
The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first.
Common Problems This Part Fixes
Water pooling or leaking underneath the dishwasher
Poor washing performance from one or both spray arms
Unusual noise during the wash cycle
Water not properly directed to the correct spray arm
Inconsistent cleaning results between the upper and lower racks
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers:
WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB.
Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement diverter assembly — controls water flow to the spray arms
Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms
Valve and float assembly engineered to optimize water flow while minimizing noise
Direct drop-in replacement matching the original mounting and connections
Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK
Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
DIY-friendly repair
Product Specifications
Part Number
WD19X25278
OEM Part Number
WD19X25278
Part Type
Dishwasher Diverter Valve Assembly
Condition
Aftermarket Replacement
Function
Controls water flow direction to the upper and lower spray arms
Design
Valve and float assembly
Repair Difficulty
Easy to Moderate — DIY-friendly
Quantity
1 diverter assembly
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
I'm seeing water pooling under my dishwasher. Is this the part I need?
Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it.
Any tips to avoid damaging the new part during installation?
Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this.
Is this a difficult repair?
No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor
The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line.
Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535.
Quick Answer
The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause.
Common Problems This Part Fixes
Dishwasher won't drain at the end of the cycle
Water pooling at the bottom of the tub after a completed cycle
Grinding or humming noise coming from the pump area
Dishwasher won't start a new cycle because it detects leftover water from the previous one
Dishes not getting properly cleaned due to poor water circulation
Pump running but producing little or no actual drainage
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform.
Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Frigidaire OEM part — factory-specified motor speed and impeller design
Pumps water out of the tub and through the drain hose at the end of each cycle
Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure
Includes pump motor, impeller, and seal
Rated 120V, 60Hz, 35W, 0.8A, 3600RPM
1/4" male terminals for a direct plug-in electrical fit
Direct drop-in replacement — no modification required
Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535
Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
A00126401
Part Type
Dishwasher Drain Pump Motor Assembly
Condition
Genuine OEM
Brand
Frigidaire
Voltage
120V
Frequency
60 Hz
Wattage
35 W
Amperage
0.8 A
Motor Speed
3600 RPM
Terminals
1/4" male
Kit Contents
Pump motor, impeller, seal
Dimensions
Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H
Color
White / Green
Repair Difficulty
Easy to Moderate — under an hour
Quantity
1 drain pump motor assembly
Compatible Brands
Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore
Installation Notes
⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves.
Frequently Asked Questions
My dishwasher won't drain. How do I know if it's actually the pump and not something simpler?
Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix.
I already replaced the pump and it's still not draining. What should I check next?
This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing.
Does this kit include the check valve flapper?
This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WD12X24058 Dishwasher Genuine OEM Detergent Dispenser
Detergent Dispenser
Fits select LG Dishwasher models.
Replaces Part Numbers: AGM75469801, AP6234070, PS12078829.
Description: This Detergent Module is a Genuine OEM part for select LG dishwasher models. It is designed to dispense the correct amount of detergent at the appropriate times during the wash cycle, ensuring that dishes are cleaned effectively. The module holds the detergent and releases it into the dishwasher when needed, contributing to the overall performance and efficiency of the appliance.
W11230103 Dishwasher Sump Pump and Motor
Replaces Part Numbers: W11230103, W10620220, 4591207, AP6329759, PS12349660.
Description: This Pump & Motor is an OEM part for Whirlpool dishwasher models. It serves as the heart of the wash system by providing water circulation and spray throughout all cycles. The pump circulates water mixed with detergent to clean dishes effectively.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W10195039 Dishwasher Float Switch
The XPARTCO W10195039 is an aftermarket replacement float switch for Whirlpool-built dishwashers sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana and related brand names. The float switch is the safety device that shuts off the water fill valve if the water level gets too high before the timed fill cycle ends, so a failed float can mean overfilling or a dishwasher that won't fill properly.
This is a direct-fit aftermarket replacement for the original Whirlpool float switch, which is sold as W10195039 and WPW10195039. Float problems can look like valve or control problems, so check the float for a stuck or damaged action before replacing it.
Quick Answer
The XPARTCO W10195039 Float Switch fixes a Whirlpool-built dishwasher that overfills, leaks from too much water, or won't fill because the float is stuck, damaged, or no longer switching. It is also listed as WPW10195039. Classic symptom: water keeps filling past the normal level, or the dishwasher won't fill and the float looks stuck or cracked.
Common Problems This Part Fixes
Dishwasher overfills or the water level gets too high
Water leaking from too much water in the tub
Dishwasher won't fill because the float switch is stuck or failed
Float is cracked, broken, or doesn't move freely
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This float switch directly replaces the following part numbers:
WPW10195039, W10195039, W10734532, 1872053, MS10-06, AP6016738, AWP49215, EAP11750031, PD00002753, PS11750031
W10195039 is the older Whirlpool number and WPW10195039 is its current replacement. W10734532 comes from a single retailer cross-reference, so confirm against your dishwasher's parts diagram, or contact our support team, if your model calls out a different number.
Compatibility
This float switch is listed for Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana, and Inglis dishwashers, including these examples:
Kenmore 66513979K017, 66515049K111, 66513964K017, 66512776K310
ADB1100AWB0, CDBW4400SB0, KUDC10FBBL0, KUDS30FXSS0, MDB4709PAB0
Note: The models above are a sample of a much longer list, not a full list. A dishwasher that won't fill can also be caused by the inlet valve, so test the float and valve before ordering. Confirm your model number against your parts diagram, or contact our support team to verify fit.
Key Features
Direct-fit aftermarket float switch for Whirlpool-built dishwashers
Shuts off the fill valve if the water level gets too high
Replaces both W10195039 and WPW10195039
Fits Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air and related brands
Product Specifications
Part Number
W10195039
OEM Part Number
W10195039, WPW10195039
Part Type
Dishwasher Float Switch
Condition
Aftermarket Replacement
Application
Whirlpool-Built Dishwashers
Installation Notes
⚠️ Disconnect Power and Shut Off the Water Unplug the dishwasher or switch off its circuit breaker, and turn off the water supply before beginning. Wear work gloves to protect your hands. Follow your model's service guide to reach the float switch, and note the position of each wire connector before disconnecting it. Install the new float switch in the same position, reconnect the wires, and check that the float moves freely before closing the dishwasher. Run a cycle and check for leaks.
Frequently Asked Questions
What does the float switch do?
It shuts off the water fill valve if the water level gets too high before the timed fill cycle ends. It is a safety device that helps prevent overflow.
My dishwasher still won't fill. Will this fix it?
Only if the float is the cause. A dishwasher that won't fill can also have a bad inlet valve, a clogged inlet screen, or a control problem. Check that the float moves freely and test the valve first.
Is W10195039 the same as WPW10195039?
Yes. W10195039 is the older Whirlpool number and WPW10195039 is its replacement. This float switch covers both.
Will this fit my dishwasher?
It is listed for many Whirlpool-built dishwashers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
