WPW10455261 Dishwasher Genuine OEM Pump and Motor Assembly
Fits specific Whirlpool, Maytag, Kenmore Dishwasher models
Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it.
Replaces Part Numbers: WPW10455261, W10455261, 2312159, W10500284, AP6021679, PS11755005.
California Residents only
WARNING: California’s Proposition 65
WP694089 Dryer Genuine OEM Blower Wheel
The WP694089 is a Genuine OEM replacement dryer blower wheel compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Roper, Estate, Crosley, Inglis, Caloric, Hardwick, and Glenwood 29-inch dryers with a lint filter on top. The blower wheel works together with the drive motor to create the airflow that makes drying possible — it draws heated air through the heating element, pushes it into and through the drum to evaporate moisture from your clothes, and exhausts it out through the vent system. Without a properly functioning blower wheel, airflow drops, drying times increase dramatically, and the dryer may overheat.
Measures 8-5/8" in diameter. Mounts on the motor's blower shaft with left-hand threads — to remove the old blower wheel, turn it clockwise (the reverse of standard threading). This blower wheel fits dryers where the motor is mounted in the rear of the cabinet, not the front. Common causes of failure: the internal sleeve wears out over time, allowing the wheel to wobble on the motor shaft; lint, socks, or small clothing articles escape past the lint filter and jam the wheel; or the plastic fins crack and break from age or debris impact. It directly replaces WP694089, WP694089VP, AP6010602, 279500, 279711, 299678, 338840, 343939, 343941, 686172, 695499, DE601, PS11743785, AH383953, EA383953, and PS383953. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The WP694089 Dryer Blower Wheel fixes Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, and Admiral 29" dryers that take too long to dry, make loud thumping/rattling/scraping noises, have weak airflow, or won't tumble. 8-5/8" diameter. Left-hand threads (turn clockwise to remove). Fits rear-mounted motor dryers with lint filter on top. Replaces WP694089, WP694089VP, AP6010602, 279500, 279711, 299678, 338840, 343939, 343941, 686172, 695499, DE601, PS11743785. Check for trapped lint, socks, or debris before replacing — a jammed wheel may not be broken.
Common Problems This Part Fixes
Dryer takes too long to dry clothes — reduced airflow from a worn or damaged blower wheel
Loud thumping, rattling, or scraping noise during operation — debris caught in the wheel or broken fins
Weak or no airflow from the exhaust vent — wheel wobbling or not spinning properly
Clothes still damp at the end of the cycle — inadequate air circulation
Dryer overheating — restricted airflow causing heat buildup
Blower wheel wobbling on the motor shaft — worn internal sleeve
Sock, small garment, or lint clump jammed in the blower wheel
Blower wheel fins cracked or broken from debris impact or age
Dryer running but drum not turning — severely damaged wheel preventing motor from spinning
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer blower wheel directly replaces the following OEM and cross-reference part numbers:
WP694089, 694089, 279500, 279711, 299678, 338840, 343939, 343941, 695499, DE601, PD00002470, EAP11743785, AP6010602, AWP48132, OEM18031815, PS11743785
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some Whirlpool dryers use a different blower wheel (such as the 697772) — verify your original part number or model number before ordering.
Compatibility
This blower wheel is compatible with select 29-inch dryers with a lint filter on top from the following brands:
Whirlpool dryers — 29" models with lint filter on top and rear-mounted motor (WED, LER, LEQ, LE series and related)
Kenmore / Sears dryers — select Whirlpool-built models (110-series)
Maytag dryers (select Whirlpool-built models)
KitchenAid dryers (select models)
Jenn-Air dryers (select models)
Amana dryers (select models)
Magic Chef dryers (select models)
Admiral dryers (select models)
Roper dryers (select models)
Estate dryers (select models)
Crosley, Inglis, Caloric, Hardwick, Glenwood dryers (select Whirlpool-built models)
Note: This blower wheel fits dryers where the motor is mounted in the rear of the cabinet (not the front). If your dryer has the motor in the front, this is not the correct blower wheel. Confirm your dryer model number before ordering. Also: before replacing the blower wheel due to noise, check for trapped lint, socks, or small garments caught in the wheel — clearing the debris may resolve the noise without needing a new part.
Key Features
Dryer blower wheel — draws heated air through the heating element, circulates it through the drum, and exhausts it through the vent system
Resolves "takes too long to dry," "loud noise," "weak airflow," "overheating," and "clothes still damp" symptoms when caused by a worn or damaged blower wheel
8-5/8" diameter — matches the original OEM dimensions
Left-hand threads — mounts on the motor's blower shaft (turn clockwise to remove, counterclockwise to install)
Designed for 29" Whirlpool-built dryers with lint filter on top and rear-mounted motor
Replaces WP694089, WP694089VP, AP6010602, 279500, 279711, 299678, 338840, 343939, 343941, 686172, 695499, DE601, PS11743785, AH383953, EA383953, and PS383953
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Roper, Estate, Crosley, Inglis, and more
Genuine OEM replacement part.
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
WP694089
OEM Part Number
WP694089
Part Type
Dryer Blower Wheel
Condition
Genuine OEM
Application
29" Dryers with Lint Filter on Top (Whirlpool platform)
Diameter
8-5/8"
Threading
Left-hand threads (clockwise to remove)
Motor Position
Rear-mounted motor (not front-mounted)
Function
Circulates heated air through the drum and out the exhaust vent
Location
Attached to the motor's blower shaft inside the blower housing
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Roper, Estate, Crosley, Inglis, Caloric, Hardwick, Glenwood
Installation Notes
⚠️ Disconnect Power Before Starting — 240V Circuit (Electric) or Gas Line (Gas) — Wear Work Gloves Disconnect power at the breaker before beginning — electric dryers operate on a 240V circuit. For gas dryers, also shut off the gas supply. Wear work gloves and safety glasses. Pull the dryer away from the wall. Access the blower wheel by removing the dryer's back panel — remove the screws securing the rear panel and set it aside. Locate the blower housing at the bottom rear of the dryer, connected to the motor. The blower wheel is inside this housing, mounted on the motor's blower shaft. Remove the blower housing cover or clamp to expose the wheel. Important: the blower wheel has left-hand threads. To remove the old blower wheel, turn it clockwise (the opposite of standard threading). If the wheel is stuck on the shaft, hold the motor pulley on the other end of the shaft to prevent it from turning while you unscrew the wheel. If the old wheel's plastic hub has seized on the shaft from age, you may need to use a flat-blade screwdriver to gently pry it — some customers report the old wheel breaks apart during removal, which is fine since you're replacing it. Before installing the new wheel, clean out any lint, debris, socks, or clothing articles from the blower housing. Thread the new 694089 blower wheel onto the motor shaft counterclockwise (remember: left-hand threads — counterclockwise tightens). Tighten firmly by hand. Reassemble the blower housing, reinstall the rear panel, push the dryer back into place, and restore power. Run a test cycle and check airflow at the exhaust vent. Tools needed: Nut driver, Phillips screwdriver, flat-blade screwdriver, work gloves, safety glasses.
Frequently Asked Questions
My dryer is making a loud thumping or rattling noise — is the blower wheel the cause?
It's one of the most common causes of dryer noise, yes. There are two main ways the blower wheel causes noise: first, lint, socks, or small clothing articles can escape past the lint filter and get caught in the wheel, where they hit the housing with each rotation — producing a rhythmic thumping or scraping sound. Second, the wheel's internal sleeve can wear out over time, allowing the wheel to wobble loosely on the motor shaft, which creates a rattling or vibrating noise. Before ordering a new wheel, check for trapped debris first — pull the back panel and inspect the blower housing. Clearing a stuck sock may solve the problem immediately. If the wheel wobbles freely on the shaft or has cracked/broken fins, it needs replacement.
Why does the blower wheel have left-hand threads?
The left-hand (reverse) threading is by design. The motor shaft spins in a direction that would naturally loosen a standard right-hand threaded wheel over time. By using left-hand threads, the motor's rotation actually tightens the wheel onto the shaft during operation, preventing it from working loose while the dryer runs. This means: turn clockwise to remove the old wheel (opposite of what you'd expect), and turn counterclockwise to tighten the new wheel onto the shaft. Many customers get stuck at this step because they instinctively turn counterclockwise to loosen — so if the wheel seems stuck, try turning it the other way first.
My dryer takes forever to dry — is the blower wheel the issue?
It can be, but check the easier things first. Long drying times are usually caused by restricted airflow, and the most common culprit is a clogged or kinked exhaust vent hose — clean the entire vent path from the dryer to the outside wall first. Also clean the lint filter and check the lint trap housing for buildup. If the vent system is clear and drying times are still long, the blower wheel is a strong candidate: a worn sleeve that lets the wheel wobble reduces its ability to move air efficiently, and cracked fins reduce airflow even if the wheel still spins. You can test by running the dryer and checking the airflow at the outside exhaust vent — weak or no airflow with a clear vent path points to the blower wheel.
Does this fit dryers with the motor in the front?
No — the 694089 blower wheel is designed for 29" Whirlpool-platform dryers where the motor is mounted in the rear of the cabinet. If your dryer has the motor in the front, it uses a different blower wheel. The easiest way to confirm: look at the back of the dryer — if you can see the motor and blower housing when the rear panel is removed, the motor is in the rear and this wheel fits (verify your model number too). If the motor is accessible from the front, this is not the correct part. Contact our support team with your model number and we'll confirm.
The old blower wheel is stuck on the shaft — how do I get it off?
First, make sure you're turning it the right direction — this has left-hand threads, so turn clockwise to loosen (the opposite of normal). If it's truly stuck from age or corrosion: hold the motor pulley on the other end of the shaft with one hand (or use pliers wrapped in a cloth) to keep the shaft from spinning, then turn the blower wheel clockwise with the other hand. If the plastic hub has seized, a flat-blade screwdriver can help gently pry it. In many cases, an old seized blower wheel will crack and break apart during removal — that's perfectly fine since you're replacing it anyway. Just make sure all the old pieces are cleared from the blower housing before installing the new wheel.
Is this an OEM or aftermarket part?
This is a Genuine OEM replacement part. It is a genuine Whirlpool OEM part, this original WP694089 blower wheel used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and related 29" dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM ✓ Compatibility Support ✓ Secure Checkout
DD31-00016B Dishwasher Drain Pump Motor - Compatible with Samsung Dishwashers
Product Description
Restore your dishwasher’s performance with the DD31-00016B Dishwasher Drain Pump Motor. This genuine OEM replacement pump ensures efficient water drainage during wash and rinse cycles, preventing water pooling and error codes. Designed for Samsung dishwashers.
Replaces part numbers: DD31-00016B, AP7244901, PS17504318, EAP17504318, PD00089738.
Verify your model number or contact support for assistance.
Key Features:
✅ Brand Compatibility: Fits select Samsung dishwasher models.
💧 Specifications: OEM drain pump motor, 120V, 60Hz, 3.5" x 3.5" x 2.5", with plastic impeller and electrical connector for reliable drainage. DD31-00016B Motor Bldc PUMP; BD15-3C, 2800-3400RPM, 230
💰 Cost-Effective: OEM performance at a competitive price.
🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–40 minutes.
🛡️ Reliable Fixes: Resolves water pooling, poor drainage, or 5E/SE error codes.
Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today!
Add to cart now for a budget-friendly fix!
XPARTCO W11612326 Dishwasher Circulation Pump (OE)
OE-style dishwasher circulation pump designed to move water through the spray arms and restore proper dishwasher wash performance.
✓ Dishwasher Repair Part ✓ Replaces W11612326 ✓ Compatibility Support
Product Description
The XPARTCO W11612326 Dishwasher Circulation Pump moves water through the dishwasher spray arms during the wash cycle. A faulty circulation pump can cause poor cleaning, weak water pressure, unusual pump noise, or incomplete wash performance.
Replacing a failed dishwasher circulation pump can help restore proper water circulation and improve dishwashing results.
What is OE ?: “OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts. They offer identical fit and function to OEM (Original Equipment Manufacturer) components but are typically sold under independent brands like XPARTCO for better affordability.
Quick Answer
If your dishwasher is not cleaning properly, has weak spray arm pressure, or makes unusual pump noise, the W11612326 circulation pump may need replacement.
⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure.
Common Problems This Part Fixes
Dishwasher not cleaning dishes properly
Weak spray arm water pressure
Water not circulating during wash cycle
Unusual circulation pump noise
Poor dishwasher wash performance
Replaces part Number
W11612326, W10879262, W10805386, W11521435, AP7193729, PS16744934, 4460096, AP6027386, AWP45622, AP16744934, PD00080710, PS11759751.
Compatibility
This part fits select Whirlpool, KitchenAid, Maytag, Amana, and compatible dishwasher models using part number W11612326.
Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure.
Key Features
Dishwasher circulation pump replacement
Helps restore proper water circulation
Supports spray arm water pressure
Designed for compatible dishwasher models
“OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts.
Product Specifications
Brand
XPARTCO
Part Type
Dishwasher Circulation Pump
Primary Part Number
W11612326-OE
Compatible Appliance Type
Dishwasher
Condition
New
Installation
Disconnect power and water supply before installation. Inspect hoses, seals, and wiring connections after installation.
Troubleshooting Guide
⚠️ Disconnect power and water supply before servicing the dishwasher.
Check spray arms and filters for blockage before replacing the pump.
Inspect the circulation pump area for leaks or unusual noise.
Verify wiring connections are secure.
Replace the circulation pump if water circulation problems continue.
When Should You Replace This Part?
Replace the dishwasher circulation pump if the dishwasher has poor cleaning performance, weak spray pressure, unusual pump noise, or water is not circulating during the wash cycle.
Shop With Confidence
We are a U.S.-based appliance parts retailer specializing in high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse.
✓ Fast Shipping ✓ OE-Style Replacement ✓ Compatibility Support ✓ Secure Checkout
W10518394 Genuine OEM Whirlpool Dishwasher Heating Element
The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades.
This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed.
Common Problems This Part Fixes
Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase
Wash water not getting hot enough — poor cleaning performance even with proper detergent
Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation
Heated dry cycle not working — no warm air at the end of the cycle
Element visibly burned through, broken, or showing arcing damage
Multimeter continuity test on the element shows an open circuit (no continuity)
Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element)
Detergent not fully dissolving — water too cool to activate the formulation
Replaces Part Numbers
This dishwasher heating element directly replaces the following OEM and cross-reference part numbers:
W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead.
Compatibility
This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including:
Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models
Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram)
Maytag dishwashers — select models (verify with parts diagram)
KitchenAid dishwashers — select models
Amana dishwashers — ADB1400AGW and related models
Kenmore / Sears dishwashers — select Whirlpool-built models
Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase
Rated 1200W for efficient heating and reliable temperature control
Oval-shape element approximately 15" L x 3" W x 3" H
Mounts in the bottom of the dishwasher tub, secured underneath with large nuts
Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement
Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times)
Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070
Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
W10518394
Part Type
Dishwasher Heating Element
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Shape
Oval (NOT interchangeable with horseshoe-style elements)
Wattage
1200W
Dimensions
Approximately 15" L x 3" W x 3" H
Mounting Location
Bottom of dishwasher tub
Related Parts (Sold Separately)
Rubber Washer (717273), Heater Nut (8268548)
Post-Install Step
Diagnostic reset required on most Whirlpool dishwashers
Compatible Brands
Whirlpool, Maytag, KitchenAid, Amana, Kenmore
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses.
Frequently Asked Questions
Why are my dishes coming out wet — is the heating element the cause?
Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed.
After installing the new element, the dishwasher still isn't heating — why?
On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well.
How is the W10518394 different from horseshoe-shape heating elements?
The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher.
Do I need to replace the rubber washers and nuts when installing this?
Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine GE OEM Part
GE WD24X25325 Dishwasher Genuine Fan Vent Assembly
Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers.
Product Overview
The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system.
The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance.
Quick Answer
WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying.
Common Problems This Part May Fix
Poor drying performance
Excess moisture remaining after a cycle
Door vent fan does not run
Unusual noise from the vent/blower area
Moist air is not being exhausted through the door vent
Replaces and Cross-References
WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435.
Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering.
Compatibility
Fits select GE and Haier dishwashers. Compatible model examples include:
CDT800P2N0S1
CDT805P2N0S1
CDT845P2N3S1
DDT700SBN0TS
GDF645SSN0SS
GDT645SFN3DS
GDT665SFN0DS
GDP665SYN3FS
PDT715SYN2FS
PDT715SFN0DS
PDP715SYN3FS
QDP555SYN0FS
Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly.
Key Features
Genuine GE Appliances OEM part
Complete door-vent blower/fan assembly
Circulates air through the dishwasher door vent
Helps reduce moisture during drying
For select GE and Haier dishwashers
Product Specifications
Manufacturer
GE Appliances
Manufacturer Part Number
WD24X25325
Part Type
Dishwasher Fan Vent / Door Vent Blower Assembly
Condition
New
Part Quality
Genuine OEM
Application
Dishwasher Door Ventilation / Drying System
Approx. Shipping Weight
0.5 lb
Installation Notes
Disconnect electrical power to the dishwasher at the breaker before service.
Access the door vent assembly according to the appliance service procedure.
Disconnect the wiring connector carefully before removing the old fan assembly.
Transfer or reuse any hardware only as directed for the specific model.
Confirm the vent path is clear and the new assembly is fully seated before reassembly.
Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it.
Frequently Asked Questions
Is WD24X25325 a Genuine GE OEM part?
Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly.
What does this fan assembly do?
It circulates air through the dishwasher door vent to help reduce moisture during the drying stage.
Does it fit every GE dishwasher?
No. It fits specific GE and Haier models. Verify the complete model number before ordering.
Is this only the fan motor?
This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE.
Shop With Confidence
Use your dishwasher's complete model number to confirm fitment before purchase.
Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping
WD24X10018 Dishwasher Genuine Piston & Nut Assembly
Replaces Part Numbers: WD24X10018, 821081, WD22X0133, WD22X133, WD24X0199, WD24X0220, WD24X199, WD24X220, AH260690, EA260690, AP2617344, PS260690.
Description: This Piston & Nut Assembly is a Genuine parts for specific GE dishwasher models. It plays a critical role in the dishwasher’s water management system, helping to control water flow and ensuring proper drainage during the wash cycle. You should replace this piston & nut assembly if it becomes worn out or damaged. Common causes of a bad piston & nut assembly can include mineral buildup from hard water, general wear and tear from regular use, or physical damage due to debris or foreign objects in the dishwasher.
XPARTCO DD94-01002A Dishwasher Mounting Installation Kit for Samsung.
High-quality dishwasher mounting installation kit designed to help secure compatible dishwashers properly during installation.
✓ Dishwasher Installation Part ✓ Replaces DD94-01002A ✓ Compatibility Support
Product Description
The XPARTCO DD94-01002A Dishwasher Mounting Installation Kit is used to help secure compatible dishwashers during installation. Proper mounting helps keep the dishwasher stable, aligned, and safely positioned under the countertop or cabinet opening.
Replacing missing, damaged, or worn mounting hardware can help restore a secure dishwasher installation and prevent unwanted movement during use.
Quick Answer
If your dishwasher is loose, shifting, not secured under the counter, or missing mounting hardware, the DD94-01002A dishwasher mounting installation kit may be needed.
⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure.
Common Problems This Part Fixes
Dishwasher not secured properly
Missing dishwasher mounting hardware
Dishwasher shifting during use
Loose dishwasher installation
Damaged or worn mounting brackets
Replaces part Number
DD94-01002A, 2077601, AP4450818, ASM941007, PD00007402, EAP4222710, PS4222710.
Compatibility
This part fits select Samsung and compatible dishwasher models using part number DD94-01002A.
Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure.
Key Features
Dishwasher mounting installation kit
Helps secure dishwasher in place
Supports proper dishwasher alignment
Designed for compatible dishwasher models
Quality aftermarket replacement part
Product Specifications
Brand
XPARTCO
Part Type
Dishwasher Mounting Installation Kit
Primary Part Number
DD94-01002A
Compatible Appliance Type
Dishwasher
Condition
New
Installation
Disconnect power before installation. Follow the dishwasher installation instructions and verify the unit is level, aligned, and securely mounted before use.
Troubleshooting Guide
⚠️ Disconnect power before servicing or installing the dishwasher.
Check if the dishwasher is level and properly aligned.
Inspect mounting brackets and screws for damage or missing hardware.
Confirm the dishwasher does not shift when the door is opened or closed.
Replace the mounting kit if hardware is missing, damaged, or no longer secure.
When Should You Replace This Part?
Replace the dishwasher mounting installation kit if the dishwasher is loose, shifting, not properly secured, or if the original mounting hardware is missing or damaged.
Shop With Confidence
We are a U.S.-based appliance parts retailer specializing in high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse.
✓ Fast Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
```
WR2X7054CM Dishwasher / Refrigerator Push-on Nut
Push on retainer clip.
Used on GE dishwashers and refrigerators.
Replaces Part Numbers:WR2X7054, WD02X0429, WD2X429, WR02X7054, AH298353, EA298353, AP2059046, PS298353.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
154825001 Genuine OEM Frigidaire Dishwasher Heating Element
The 154825001 is a genuine Frigidaire OEM round heating element that sits exposed at the bottom of the dishwasher tub. Unlike a hidden element concealed beneath the tub floor, this is a visible ring-shaped element you can see sitting right in the bottom of the wash chamber. It serves two jobs: it heats the wash water to the temperature needed to properly dissolve detergent and break down grease and food soil, and at the end of the cycle it provides the heat that drives the drying phase, helping moisture evaporate off your dishes rather than leaving them wet.
Mounted through a 0.98" hole with two mounting nuts and connected by two wire terminals, this element carries a pair of white alignment dots that must line up with the tub's retaining clips during installation. Over time, mineral buildup from hard water, general corrosion, or simple electrical wear can cause the element to fail. A failing or dead element produces a specific and recognizable pattern: water never gets hot enough to clean effectively, dishes come out wet at the end of the cycle instead of dry, and the whole cycle may run noticeably longer as the dishwasher's control tries to compensate. It directly replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, and EAP3653449. As a genuine OEM part, the 154825001 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The 154825001 Genuine OEM Frigidaire Dishwasher Heating Element fixes Frigidaire, Kenmore, Electrolux, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers with dishes that don't get properly clean, dishes that come out wet instead of dry, or cycles that take longer than they used to. Exposed round heating element, 0.98" mounting hole, 2 wire terminals. Replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, EAP3653449. Before replacing, test the old element with a multimeter for resistance — a bad control board relay can produce identical symptoms with a perfectly good element.
Common Problems This Part Fixes
Dishes not getting properly clean because wash water isn't reaching the correct temperature
Dishwasher not drying dishes — items come out wet at the end of the cycle
Cycle taking noticeably longer than usual to complete
Visible damage, corrosion, or discoloration on the element itself
Element that doesn't glow or heat up when the wash cycle is running
Water leaking near the high-temperature wire connector at the element terminals
Mineral scale buildup visible on or around the element
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher heating element directly replaces the following OEM and cross-reference part numbers:
154825001, 154482901, 154663801, 2308825, AP5628696, AFR14520, EAP3653449, PD00000951, PS3653449.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This heating element is compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers, spanning a wide range of model series including BBBD, BGBD, BGHD, DGBD, DGCD, DGHD, FDB, FDBB, FDBD, FFBD, FFID, FGBD, FGCD, FGHD, FGID, FPHD, FPID, GLD, GSB, LEDB, LFBD, LFID, LGBD, LGHD, and PLD.
Verified model numbers include: FFCD2413UW1A, FGID2466QF4A, FGID2466QF5A, FFID2426TD1A, FGBD2438PF4A, FGHD2465NF1A, FGHD2433KF1, LFID2426TF1A, LFID2422RF0A, LFID2422RF3B, LFID2422RF4B, LFID2426TF4A, LFID2426TF5A, LGBD2431LF0A, LGBD2431NF0B, LGBD2431NF1B, LGBD2432LW0A, LGBD2432LW0B, and CDB350/CDB500/CDB900 series models. Also fits Kenmore 587-series, Crosley CBD-series, Kelvinator KADB240, and White-Westinghouse WWBD2400 dishwashers.
Note: This is an exposed round heating element sitting visibly in the bottom of the tub, not a hidden element mounted underneath. It is not interchangeable with hidden/concealed heating elements used on other dishwasher platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Frigidaire OEM part — factory-specified heating output and terminal configuration
Exposed round design sits in the tub bottom for direct water heating and drying support
Resolves "not cleaning properly," "not drying," and "cycle taking too long" symptoms caused by element failure
0.98" mounting hole with two mounting nuts and wire terminals
Two white alignment dots for correct positioning in the tub's retaining clips
Direct drop-in replacement — no modification required
Replaces 154482901, 154663801, 2308825, AP5628696, PS3653449, and EAP3653449
Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
154825001
Part Type
Dishwasher Round Heating Element (Exposed)
Condition
Genuine OEM
Brand
Frigidaire / Electrolux
Location
Bottom of the wash tub (exposed, visible)
Mounting Hole
0.98 in.
Terminals
2 wire connections + 2 mounting nuts
Alignment
2 white dots must align with tub retaining clips
Repair Difficulty
Medium — basic dishwasher familiarity required
Tools Required
Screwdrivers, wrench set
Quantity
1 heating element
Compatible Brands
Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Handle The Element Carefully Disconnect power at the circuit breaker and shut off the water supply before beginning. Wear work gloves. On many models you'll need to pull the dishwasher out from under the counter to access the undercarriage — remove the two screws securing the unit to the counter first. Remove the lower rack and the lower spray arm (it typically pushes down and twists to unlock) to access the element inside the tub. From underneath, disconnect the two wires from the element's terminals and remove the two mounting nuts with a 1/2" wrench, taking care not to overtighten when you reach the new element — over-torquing can crush the sealing washers and cause a leak at the connector. Lift the old element free from its retaining clips inside the tub. To install the new 154825001, locate the two white alignment dots on the element and position them so they slide into the tub's retaining clips correctly — this ensures the element seats in its proper orientation. Push the terminals down through the mounting hole, then from underneath, reinstall and tighten the mounting nuts snugly but not excessively. Reconnect the two wires to the terminals, reinstall the lower spray arm and press it down to lock it in place, and reinstall the lower rack. Restore water and power, then slide the dishwasher back into place and secure it to the counter with its mounting screws. Run a test cycle and check underneath for any leaks at the element connection before considering the repair complete. Tools needed: screwdriver, 1/2" wrench, work gloves.
Frequently Asked Questions
How do I know it's the heating element and not something else, like the control board?
Before replacing the element, it's worth testing it with a multimeter for resistance — a healthy element typically reads in the neighborhood of 14 ohms, though exact values vary by model. If the old element tests fine but dishes still aren't drying or getting hot enough, the more likely cause is upstream of the element itself, such as a control board relay that isn't sending power to it correctly. Some owners have replaced a perfectly good element only to find the actual fault was a bad solder connection on the control board relay — testing first can save you an unnecessary purchase.
Can I clean the element instead of replacing it?
Light surface cleaning to remove mineral scale buildup is reasonable and can sometimes help if reduced heating output is due to scale insulating the element. However, if the element tests as an open circuit (no continuity) or shows visible damage, cracking, or corrosion through the metal sheath, cleaning won't restore it — replacement is the correct fix at that point.
I noticed water leaking near the element's wire connector. Is that related?
Yes, this is a documented failure point on this element design — the high-temperature wire connector at the terminals can develop a leak, especially if the mounting nuts were overtightened during a prior installation and damaged the sealing washer. When installing the new element, tighten the mounting nuts snugly but avoid excessive force, which helps prevent this same leak point from recurring.
Do I really need to pull the dishwasher out from under the counter?
On most installations, yes — accessing the mounting nuts and wire terminals underneath the tub requires pulling the unit forward after removing the two screws that secure it to the counter. Some technicians have managed the nut removal with a deep socket without fully pulling the unit, but planning for full access makes the job considerably easier, especially the first time.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original heating output, mounting configuration, and terminal layout of the element originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
