Search results for "dishwasher seal"

WD12X10304 Genuine GE OEM Rack End Cap Clip Replaces Part Number:  WD12X10304, 1556527, WD12X0344, WD12X344, WD30X97, AH2370502, EA2370502, OEM13454003, AP4484666, PS2370502. Description: This Rack Slide End Cap is a Genuine OEM part for specific GE dishwasher models. This small but essential component is designed to secure the end of the rack slide rail, preventing the dish racks from sliding off the track or becoming misaligned.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

4581DD3002ACM Dishwasher Upper Dishrack Roller Upper rack roller for LG & Kenmore Elite Dishwashers. Sold individually, but recommend replacing in sets. Includes roller and clip on axel. Replaces Part Numbers: 4581DD3002A, 4581DD9001B, 1266813, AH3523050, EA3523050, AP4437685, PS3523050.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11087376 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers:W11087376, W10917114, 4534143, AP6237961, PS12074533. California Residents only WARNING: California’s Proposition 65 

Read more less

5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm The 5304517203 is a genuine Frigidaire OEM lower spray arm for Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers. Positioned at the bottom of the dishwasher tub, this arm rotates as water is pumped through it, spraying water in all directions through its nozzle openings to clean dishes in the lower rack. It snaps directly into the bottom sump assembly and is essential for proper water distribution during the wash cycle. Made of durable plastic and metal, finished in gray/blue. Over time, the arm can crack, warp, or wear from general use and repeated exposure to hot water and detergent — high heat exposure in particular is a documented cause of failure. A broken or worn spray arm typically shows up as visible damage on the arm itself, dishes in the lower rack not getting cleaned properly, reduced or uneven water coverage, or the arm having difficulty rotating or getting stuck. It directly replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Quick Answer The 5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm fixes Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers where the lower rack isn't getting cleaned properly, water coverage is reduced or uneven, or the arm won't rotate freely or has visible cracks. Snaps into the bottom sump assembly. Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623. After installing, confirm the arm spins freely by hand and doesn't contact the heating element before running a cycle. Common Problems This Part Fixes Dishes in the lower rack not getting cleaned properly Reduced or uneven water coverage during the wash cycle Spray arm that won't rotate freely or gets stuck Visible cracks, warping, or damage on the arm itself Arm that has come loose or detached from the sump assembly Clogged nozzle holes reducing water pressure and spray coverage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher lower spray arm directly replaces the following OEM and cross-reference part numbers: 5304517203, 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lower spray arm is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers built on the same platform. Note: Non-genuine versions of this exact part number are sold by several third-party sellers. A customer using a non-genuine version of this spray arm reported it came loose and broke during operation, so confirm you're ordering the genuine Frigidaire part rather than a lower-cost imitation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified nozzle pattern and rotation fit Snaps directly into the bottom sump assembly for a secure, no-tools installation Resolves "not cleaning lower rack dishes," "uneven water coverage," and "won't rotate freely" symptoms Durable plastic and metal construction, gray/blue finish Approximate dimensions: 16.00" x 3.10" x 3.10" (L x W x H) Direct drop-in replacement — no modification required Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Compatible with Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5304517203 Part Type Dishwasher Lower Spray Arm Condition Genuine OEM Brand Frigidaire Location Bottom of the dishwasher tub, in the lower sump assembly Material Plastic and metal Color Gray / Blue Dimensions Approx. 16.00" x 3.10" x 3.10" (L x W x H) Repair Difficulty Very Easy — no tools required Quantity 1 lower spray arm Compatible Brands Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Confirm Clearance From The Heating Element Disconnect power to the dishwasher and shut off the water supply before beginning. Wear work gloves. Open the dishwasher and pull out the lower rack, setting it aside. Remove the old lower spray arm by releasing the locking tabs on each side and gently pulling it off the sump assembly. Snap the new 5304517203 spray arm onto the sump assembly in the same position. Before closing everything up, spin the arm gently by hand to confirm it rotates freely and does not make contact with the heating element — a real customer account described a spray arm and its support becoming loose and falling into the tub during use, so it's worth double-checking that the arm is fully and securely seated before running a cycle. Return the lower dish rack to its position and close the dishwasher door. Restore power and water, then run a test cycle to confirm the arm spins smoothly and dishes in the lower rack are getting properly cleaned. Tools needed: none. Frequently Asked Questions My dishes in the lower rack aren't getting clean. Is this the part I need? Yes, this is one of the most common symptoms of a worn or damaged lower spray arm. If the arm is cracked, clogged, or not rotating freely, water can't reach dishes in the lower rack evenly, leaving them dirty even when the upper rack comes out clean. I've read that a spray arm can come loose during operation. How do I prevent that? This has been reported, particularly with non-genuine imitation parts under the same number. To help prevent it, make sure the new arm snaps fully and securely onto the sump assembly during installation, and spin it gently by hand to confirm it's seated correctly and rotates without wobbling before running your first cycle with it installed. Do I need any tools to replace this spray arm? No. This is a simple snap-in, snap-out repair — release the locking tabs on the old arm to remove it, and press the new one onto the sump assembly until it clicks into place. No tools are required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original nozzle pattern, dimensions, and sump connection of the lower spray arm originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11665769 Dishwasher Sump Pump and Motor Pump and Motor Assembly Replaces Part Numbers: W11665769, W11085683, W10917110, W11164469, AP7212556, PS16875975. Description: This dishwasher pump and motor assembly is compatible with specific Whirlpool, Maytag, Kenmore dishwasher models. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.

Read more less

154756401 Genuine Frigidaire Dishwasher Door Hinge Cable The 154756401 is a Genuine OEM Frigidaire replacement dishwasher door hinge cable compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers. The door hinge cable runs through a pulley system at the base of the dishwasher door and is responsible for balancing and controlling the weight of the door as it opens and closes. When a cable breaks or frays, the door drops down suddenly and heavily, opening with a loud bang — or may not hold itself up at all, straining the door hinges and latch with every use. This is a Genuine OEM part manufactured by Frigidaire to factory specifications and directly replaces the older 154578801. It is sold as a single cable — most Frigidaire dishwashers have two door hinge cables (one on each side), and it is strongly recommended to replace both at the same time. Installs in under 30 minutes with basic hand tools. Quick Answer The 154756401 Genuine Frigidaire Dishwasher Door Hinge Cable fixes dishwashers where the door drops open too fast, bangs loudly when opened, doesn't stay open at a comfortable angle, or where a broken cable is visible at the door hinges. Sold individually — replace both cables at the same time. Compatible with Frigidaire, Electrolux, Kenmore, Crosley, and Ikea dishwashers. Replaces 154578801. Common Problems This Part Fixes Dishwasher door drops suddenly and forcefully when opened — "slams" down instead of lowering gently Loud banging or crashing noise when opening the dishwasher door Door does not stay open at a horizontal position — drops all the way down Broken, frayed, or snapped door cable visible near the door hinge or base of the door Door hinge is being damaged or strained due to missing cable tension Uneven door opening — one side drops faster than the other Replaces Part Numbers This door hinge cable directly replaces the following OEM and cross-reference part numbers: 154756401, 154578801, AFR14437, PD00082115, AP7212793, PS17217958. 154756401 is the current updated part number superseding the older 154578801. Contact our support team with your model number if you need compatibility confirmation before ordering. Compatibility This door hinge cable is compatible with select dishwashers from the following brands: Frigidaire dishwashers Electrolux dishwashers Kenmore / Sears dishwashers (Frigidaire/Electrolux-built models) Crosley dishwashers Gibson dishwashers Kelvinator dishwashers Westinghouse dishwashers Ikea dishwashers (select models) Important: Most Frigidaire dishwashers use two door hinge cables — one on each side. This part is sold as a single cable. It is strongly recommended to replace both cables at the same time, as the second cable is likely to fail soon after the first. Key Features Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance Balances and controls door weight as it opens and closes — prevents sudden door drops and hinge damage Works in conjunction with the door pulley and spring system to provide smooth, controlled door movement Current updated part number — directly supersedes 154578801 Sold individually — most models require two cables (one per side); replace both at the same time Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers DIY repair — installs in under 30 minutes with basic hand tools Product Specifications Part Number 154756401 Supersedes 154578801 Part Type Dishwasher Door Hinge Cable Condition Genuine OEM Application Dishwashers Material Metal cable Sold As Single cable (most models require 2 — replace both at the same time) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, Ikea Installation Notes ⚠️ Unplug Dishwasher Before Starting Disconnect power before beginning any repair. Open the dishwasher door and remove the inner door panel by unscrewing the screws around the perimeter of the inner door. With the inner panel removed, locate the door hinge cable routing — the cable runs from a bracket near the bottom of the door, through a pulley, and connects to the door spring tension system at the base of the dishwasher. Note how the cable is routed before removing the old one. Remove the broken cable by detaching it from the anchor points at each end. Thread the new 154756401 cable through the same pulley path and re-attach it to the anchor points at both ends, ensuring proper tension. Reinstall the inner door panel. Close and open the door to verify it moves smoothly and holds itself open horizontally. Restore power and run a short cycle to confirm normal operation. Tip: Replace both cables at the same time — the second cable will likely fail soon after the first. Tools needed: Phillips screwdriver, Torx screwdriver (T20), needle-nose pliers. Frequently Asked Questions What does the dishwasher door hinge cable do? The door hinge cable is a tensioned metal cable that runs through a pulley and connects to the door spring system to balance the weight of the dishwasher door as it opens and closes. Without the cable, the full weight of the door would cause it to drop suddenly and forcefully when opened, slamming down onto the floor or straining the hinges with every use. The cable provides the controlled, counterbalanced movement that allows the door to lower gently and stay open at a horizontal position for easy loading and unloading. How many door cables does my Frigidaire dishwasher have? Most Frigidaire dishwashers use two door hinge cables — one on the left side and one on the right side of the door. This listing is for a single cable. When one cable breaks, the other is typically close behind since both cables have endured the same amount of use. It is strongly recommended to replace both cables at the same time while the door panel is already disassembled, saving you from repeating the repair shortly after. What is the difference between 154756401 and 154578801? These are the same door hinge cable. 154756401 is the current updated part number that superseded the older 154578801 during a production revision. If your dishwasher's parts diagram or old cable label shows 154578801, the 154756401 is the correct current replacement to order. Is this compatible with Electrolux and Kenmore dishwashers? Yes — Frigidaire and Electrolux are part of the same corporate family and share many components. The 154756401 cable is compatible with select Electrolux dishwashers and with Kenmore dishwashers built on the Frigidaire/Electrolux platform. Always verify your specific model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same door hinge cable installed in compatible Frigidaire, Electrolux, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor The WPW10348269 is a genuine Whirlpool OEM drain pump motor for Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers. This pump uses an electric motor to create suction, pulling wastewater out of the tub and expelling it through the drain hose at the end of each cycle. This is the dedicated drain pump, distinct from a circulation pump — such as our WPW10605057 listing — which handles spraying water through the spray arms during the wash itself rather than draining it afterward. Rated 120VAC, 60Hz, 45W, 0.7A, with a run time pattern of 5 minutes on, 30 minutes off. Ships as a complete pump motor with impeller and O-ring. If the impeller becomes damaged or the motor shorts out and stops draining, the pump body itself can crack over time, leading to leakage — replacing the pump before that happens is the more reliable fix. Symptoms of a failing drain pump include water not draining from the tub, unusual noise such as grinding during the drain phase, or visible leaks from underneath the unit. It directly replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Quick Answer The WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor fixes Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers that aren't draining, are making grinding noise during the drain phase, or are leaking from underneath. 120VAC, 60Hz, 45W, 0.7A. Includes impeller and O-ring. Replaces W10348269, WPW10348269VP, W10084573, W10158351, 661662, 8558995, 8565839, 2813258, AP6020066, EAP11753379, PD00004898, PS11753379. This is the drain pump — a separate part from our WPW10605057 circulation pump listing, which handles spraying water rather than draining it. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Grinding noise coming from the drain pump area Water leaking from underneath the dishwasher Cycle stalling or failing to advance past the drain step Dishes not getting cleaned as a downstream effect of drainage problems Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: WPW10348269, W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Whirlpool dishwashers, and also fits select KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers built on the Whirlpool platform. Note — drain pump, not circulation pump: This is the dedicated drain pump, which removes wastewater from the tub. It is a separate part from our WPW10605057 listing, which is the circulation pump and diverter motor responsible for spraying water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified motor and impeller design Pumps wastewater out of the tub through the drain hose Resolves "not draining," "grinding noise," and "leaking underneath" symptoms caused by pump failure Complete assembly — includes pump motor, impeller, and O-ring Rated 120VAC, 60Hz, 45W, 0.7A Run time: 5 minutes on, 30 minutes off Dimensions: approximately 3-1/2"L x 3"W x 3-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10348269 Part Type Dishwasher Drain Pump Motor (with Impeller and O-Ring) Condition Genuine OEM Brand Whirlpool Function Pumps wastewater out of the tub through the drain hose Voltage 120VAC Frequency 60 Hz Wattage 45 W Amperage 0.7 A Run Time 5 min ON / 30 min OFF Dimensions Approx. 3-1/2"L x 3"W x 3-1/2"H Color White / Gray / Black / Yellow Related Part WPW10605057 circulation pump & diverter motor (different function, sold separately) Repair Difficulty Beginner to Moderate Quantity 1 drain pump motor Compatible Brands Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, Roper Installation Notes ⚠️ Unplug Dishwasher Before Starting — Removing The Unit Makes Access Easier Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This repair can be done without pulling the dishwasher out from under the counter, but many technicians find it considerably easier to access the pump if you do pull the unit out first. Remove the lower rack and any components blocking access to the tub floor, then work from underneath the dishwasher to reach the drain pump. Test the old pump for continuity with a multimeter before removing it — if it shows no continuity, or if it's getting power but still won't run, that confirms the pump has failed. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connection from the old pump, remove its mounting hardware, and pull it free. Install the new WPW10348269 in the same position, reconnect the drain hose connection securely, and reconnect the electrical connector fully. Reinstall any components removed for access and the lower rack. Restore power, run a test cycle, and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, 5/16" nut driver, 5/8" wrench, flathead screwdriver, multimeter, work gloves. Frequently Asked Questions Do I need to pull the dishwasher out from under the counter for this repair? Not strictly — this pump can be replaced without fully removing the dishwasher. That said, several customers who've done this repair note that pulling the unit out first makes access considerably easier, since you're working from underneath the appliance either way. If you have the space to pull it out, it's worth doing to make the job smoother. How do I know if the pump has actually failed? Test the pump motor with a multimeter set to continuity before replacing it. If there's no continuity, or if the pump is receiving power but still won't run, that confirms the motor has failed and the pump should be replaced. This quick check avoids replacing a part that isn't actually the problem. My old pump was leaking. Why does that happen? If the impeller becomes damaged or the motor shorts out and stops running, the pump body itself can develop a crack over time, which leads to leakage. Rather than trying to repair a leaking pump, replacing the complete assembly resolves both the drainage failure and the leak at the same time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original motor, impeller, and hose connection configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO MDS47123602 Washer Door Boot Gasket – Compatible with LG Front-Load Washers Product Description Stop leaks and restore proper sealing with the XPARTCO MDS47123602 Washer Door Boot Gasket. This high-quality aftermarket replacement forms a watertight seal between the washer door and tub, preventing water from leaking during wash and spin cycles. A worn, torn, or mold-damaged gasket can lead to leaks, odors, or excessive vibration. Replacing it with this durable XPARTCO gasket provides long-lasting protection and reliable washer performance. Replaces Part Numbers MDS47123602, MDS64237201, MDS64237202, MDS47123612, EAP3535210, PD00028934, AH3535210, EA3535210, AP5218575, PS3535210. Compatibility This replacement door boot gasket fits select LG front-load washers. Example compatible models include (but are not limited to):LG WM2650HWA, WM3470HVA, WM3570HWA, WM8000HVA, and WM3997HWA. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM fit, thickness, and sealing performance 💧 Leak-Proof Design – Forms a tight seal to prevent water escaping from the washer door 🌿 Mold-Resistant Material – High-grade rubber reduces mildew and odor buildup 🛠️ Durable Construction – Built to withstand heat, detergent, and high-spin vibration 🛡️ Fixes Common Issues – Solves leaks, mold/mildew odor, door seal tears, or water pooling 📐 Product Specification Part Number: MDS47123602 Component Type: Washer Door Boot Gasket (Door Seal) Material: High-strength, mold-resistant rubber Color: Gray (standard for LG models) Mounting: Installed between front tub and door frame using clamps Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, spring clamp tool (recommended), pliers ⚠️ Safety First: Always unplug the washer before installation to prevent electrical shock. Steps: Remove the washer top and front panel for access. Release the outer retaining spring clamp and remove the old gasket edge. Detach the inner clamp from the tub and remove the old gasket completely. Align and install the new XPARTCO MDS47123602 gasket around the tub opening. Reinstall inner clamp, then secure the outer clamp around the door frame. Reassemble the washer and perform a quick rinse cycle to test for leaks. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop washer leaks the right way — Add to Cart Now for a durable, budget-friendly replacement!

Read more less

DD62-00084A Dishwasher Genuine OEM Water Valve Description: This Water Valve is a Genuine OEM part compatible with specific Samsung dishwasher models. It is responsible for opening and closing the water supply to the dishwasher. It regulates the water pressure and ensures the proper amount of water is dispensed for each cycle.  Causes of a faulty water valve can include wear and tear over time, sediment or debris buildup, electrical component failure, or damage due to high water pressure. These factors can result in issues such as inadequate water flow, leaks, or the dishwasher not filling or draining properly. Replaces Part Numbers: DD62-00084A, AP5178218, PS4222448   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WD34X10170 Dishwasher ESCUTCHEON  Product Condition: Genuine OEM New / Old Stock Color Bisque   Replaces Part Numbers: WD34X10170, 272755, AH262062, EA262062, AP2040898, PS262062.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WD01X10393 Dishwasher Door Hinge Cable

Read more less