Search results for "dishwasher seal"

154756401 Genuine Frigidaire Dishwasher Door Hinge Cable The 154756401 is a Genuine OEM Frigidaire replacement dishwasher door hinge cable compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers. The door hinge cable runs through a pulley system at the base of the dishwasher door and is responsible for balancing and controlling the weight of the door as it opens and closes. When a cable breaks or frays, the door drops down suddenly and heavily, opening with a loud bang — or may not hold itself up at all, straining the door hinges and latch with every use. This is a Genuine OEM part manufactured by Frigidaire to factory specifications and directly replaces the older 154578801. It is sold as a single cable — most Frigidaire dishwashers have two door hinge cables (one on each side), and it is strongly recommended to replace both at the same time. Installs in under 30 minutes with basic hand tools. Quick Answer The 154756401 Genuine Frigidaire Dishwasher Door Hinge Cable fixes dishwashers where the door drops open too fast, bangs loudly when opened, doesn't stay open at a comfortable angle, or where a broken cable is visible at the door hinges. Sold individually — replace both cables at the same time. Compatible with Frigidaire, Electrolux, Kenmore, Crosley, and Ikea dishwashers. Replaces 154578801. Common Problems This Part Fixes Dishwasher door drops suddenly and forcefully when opened — "slams" down instead of lowering gently Loud banging or crashing noise when opening the dishwasher door Door does not stay open at a horizontal position — drops all the way down Broken, frayed, or snapped door cable visible near the door hinge or base of the door Door hinge is being damaged or strained due to missing cable tension Uneven door opening — one side drops faster than the other Replaces Part Numbers This door hinge cable directly replaces the following OEM and cross-reference part numbers: 154756401, 154578801, AFR14437, PD00082115, AP7212793, PS17217958. 154756401 is the current updated part number superseding the older 154578801. Contact our support team with your model number if you need compatibility confirmation before ordering. Compatibility This door hinge cable is compatible with select dishwashers from the following brands: Frigidaire dishwashers Electrolux dishwashers Kenmore / Sears dishwashers (Frigidaire/Electrolux-built models) Crosley dishwashers Gibson dishwashers Kelvinator dishwashers Westinghouse dishwashers Ikea dishwashers (select models) Important: Most Frigidaire dishwashers use two door hinge cables — one on each side. This part is sold as a single cable. It is strongly recommended to replace both cables at the same time, as the second cable is likely to fail soon after the first. Key Features Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance Balances and controls door weight as it opens and closes — prevents sudden door drops and hinge damage Works in conjunction with the door pulley and spring system to provide smooth, controlled door movement Current updated part number — directly supersedes 154578801 Sold individually — most models require two cables (one per side); replace both at the same time Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, and Ikea dishwashers DIY repair — installs in under 30 minutes with basic hand tools Product Specifications Part Number 154756401 Supersedes 154578801 Part Type Dishwasher Door Hinge Cable Condition Genuine OEM Application Dishwashers Material Metal cable Sold As Single cable (most models require 2 — replace both at the same time) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Westinghouse, Ikea Installation Notes ⚠️ Unplug Dishwasher Before Starting Disconnect power before beginning any repair. Open the dishwasher door and remove the inner door panel by unscrewing the screws around the perimeter of the inner door. With the inner panel removed, locate the door hinge cable routing — the cable runs from a bracket near the bottom of the door, through a pulley, and connects to the door spring tension system at the base of the dishwasher. Note how the cable is routed before removing the old one. Remove the broken cable by detaching it from the anchor points at each end. Thread the new 154756401 cable through the same pulley path and re-attach it to the anchor points at both ends, ensuring proper tension. Reinstall the inner door panel. Close and open the door to verify it moves smoothly and holds itself open horizontally. Restore power and run a short cycle to confirm normal operation. Tip: Replace both cables at the same time — the second cable will likely fail soon after the first. Tools needed: Phillips screwdriver, Torx screwdriver (T20), needle-nose pliers. Frequently Asked Questions What does the dishwasher door hinge cable do? The door hinge cable is a tensioned metal cable that runs through a pulley and connects to the door spring system to balance the weight of the dishwasher door as it opens and closes. Without the cable, the full weight of the door would cause it to drop suddenly and forcefully when opened, slamming down onto the floor or straining the hinges with every use. The cable provides the controlled, counterbalanced movement that allows the door to lower gently and stay open at a horizontal position for easy loading and unloading. How many door cables does my Frigidaire dishwasher have? Most Frigidaire dishwashers use two door hinge cables — one on the left side and one on the right side of the door. This listing is for a single cable. When one cable breaks, the other is typically close behind since both cables have endured the same amount of use. It is strongly recommended to replace both cables at the same time while the door panel is already disassembled, saving you from repeating the repair shortly after. What is the difference between 154756401 and 154578801? These are the same door hinge cable. 154756401 is the current updated part number that superseded the older 154578801 during a production revision. If your dishwasher's parts diagram or old cable label shows 154578801, the 154756401 is the correct current replacement to order. Is this compatible with Electrolux and Kenmore dishwashers? Yes — Frigidaire and Electrolux are part of the same corporate family and share many components. The 154756401 cable is compatible with select Electrolux dishwashers and with Kenmore dishwashers built on the Frigidaire/Electrolux platform. Always verify your specific model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same door hinge cable installed in compatible Frigidaire, Electrolux, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout  

Read more less

DD31-00016B Dishwasher Drain Pump Motor - Compatible with Samsung Dishwashers Product Description Restore your dishwasher’s performance with the DD31-00016B Dishwasher Drain Pump Motor. This genuine OEM replacement pump ensures efficient water drainage during wash and rinse cycles, preventing water pooling and error codes. Designed for Samsung dishwashers. Replaces part numbers: DD31-00016B, AP7244901, PS17504318, EAP17504318, PD00089738. Verify your model number or contact support for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung dishwasher models. 💧 Specifications: OEM drain pump motor, 120V, 60Hz, 3.5" x 3.5" x 2.5", with plastic impeller and electrical connector for reliable drainage. DD31-00016B Motor Bldc PUMP; BD15-3C, 2800-3400RPM, 230 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves water pooling, poor drainage, or 5E/SE error codes. Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

DD62-00084A Dishwasher Genuine OEM Water Valve Description: This Water Valve is a Genuine OEM part compatible with specific Samsung dishwasher models. It is responsible for opening and closing the water supply to the dishwasher. It regulates the water pressure and ensures the proper amount of water is dispensed for each cycle.  Causes of a faulty water valve can include wear and tear over time, sediment or debris buildup, electrical component failure, or damage due to high water pressure. These factors can result in issues such as inadequate water flow, leaks, or the dishwasher not filling or draining properly. Replaces Part Numbers: DD62-00084A, AP5178218, PS4222448   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WD34X10170 Dishwasher ESCUTCHEON  Product Condition: Genuine OEM New / Old Stock Color Bisque   Replaces Part Numbers: WD34X10170, 272755, AH262062, EA262062, AP2040898, PS262062.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

4581DD3002ACM Dishwasher Upper Dishrack Roller Upper rack roller for LG & Kenmore Elite Dishwashers. Sold individually, but recommend replacing in sets. Includes roller and clip on axel. Replaces Part Numbers: 4581DD3002A, 4581DD9001B, 1266813, AH3523050, EA3523050, AP4437685, PS3523050.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

XPARTCO W10195039 Dishwasher Float Switch The XPARTCO W10195039 is an aftermarket replacement float switch for Whirlpool-built dishwashers sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana and related brand names. The float switch is the safety device that shuts off the water fill valve if the water level gets too high before the timed fill cycle ends, so a failed float can mean overfilling or a dishwasher that won't fill properly. This is a direct-fit aftermarket replacement for the original Whirlpool float switch, which is sold as W10195039 and WPW10195039. Float problems can look like valve or control problems, so check the float for a stuck or damaged action before replacing it. Quick Answer The XPARTCO W10195039 Float Switch fixes a Whirlpool-built dishwasher that overfills, leaks from too much water, or won't fill because the float is stuck, damaged, or no longer switching. It is also listed as WPW10195039. Classic symptom: water keeps filling past the normal level, or the dishwasher won't fill and the float looks stuck or cracked. Common Problems This Part Fixes Dishwasher overfills or the water level gets too high Water leaking from too much water in the tub Dishwasher won't fill because the float switch is stuck or failed Float is cracked, broken, or doesn't move freely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This float switch directly replaces the following part numbers: WPW10195039, W10195039, W10734532, 1872053, MS10-06, AP6016738, AWP49215, EAP11750031, PD00002753, PS11750031 W10195039 is the older Whirlpool number and WPW10195039 is its current replacement. W10734532 comes from a single retailer cross-reference, so confirm against your dishwasher's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This float switch is listed for Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Amana, and Inglis dishwashers, including these examples: Kenmore 66513979K017, 66515049K111, 66513964K017, 66512776K310 ADB1100AWB0, CDBW4400SB0, KUDC10FBBL0, KUDS30FXSS0, MDB4709PAB0 Note: The models above are a sample of a much longer list, not a full list. A dishwasher that won't fill can also be caused by the inlet valve, so test the float and valve before ordering. Confirm your model number against your parts diagram, or contact our support team to verify fit. Key Features Direct-fit aftermarket float switch for Whirlpool-built dishwashers Shuts off the fill valve if the water level gets too high Replaces both W10195039 and WPW10195039 Fits Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air and related brands Product Specifications Part Number W10195039 OEM Part Number W10195039, WPW10195039 Part Type Dishwasher Float Switch Condition Aftermarket Replacement Application Whirlpool-Built Dishwashers Installation Notes ⚠️ Disconnect Power and Shut Off the Water Unplug the dishwasher or switch off its circuit breaker, and turn off the water supply before beginning. Wear work gloves to protect your hands. Follow your model's service guide to reach the float switch, and note the position of each wire connector before disconnecting it. Install the new float switch in the same position, reconnect the wires, and check that the float moves freely before closing the dishwasher. Run a cycle and check for leaks. Frequently Asked Questions What does the float switch do? It shuts off the water fill valve if the water level gets too high before the timed fill cycle ends. It is a safety device that helps prevent overflow. My dishwasher still won't fill. Will this fix it? Only if the float is the cause. A dishwasher that won't fill can also have a bad inlet valve, a clogged inlet screen, or a control problem. Check that the float moves freely and test the valve first. Is W10195039 the same as WPW10195039? Yes. W10195039 is the older Whirlpool number and WPW10195039 is its replacement. This float switch covers both. Will this fit my dishwasher? It is listed for many Whirlpool-built dishwashers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11665769 Dishwasher Sump Pump and Motor Pump and Motor Assembly Replaces Part Numbers: W11665769, W11085683, W10917110, W11164469, AP7212556, PS16875975. Description: This dishwasher pump and motor assembly is compatible with specific Whirlpool, Maytag, Kenmore dishwasher models. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.

Read more less

XPARTCO WD01X29878 Dishwasher Door Latch – Compatible with GE Dishwashers Product Description Restore secure door closing and proper dishwasher operation with the XPARTCO WD01X29878 Dishwasher Door Latch. This high-quality aftermarket replacement ensures the dishwasher door locks firmly during wash cycles and signals the control board that it is safe to operate. A faulty door latch can cause the dishwasher not to start, stop mid-cycle, or display door-related error codes. Replacing it with this reliable XPARTCO latch helps restore safe and dependable washing performance. XPARTCO offers cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers WD01X29878, WD01X27701, 265D1214G004, EG-380944, PD00072017, FIX16659468, 4979622, AP7176296, PS16659468. Compatibility This replacement dishwasher door latch fits select GE dishwashers. Common compatible models include (but are not limited to): GE GDT655SSJSS GE GDF630PGMWW Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and electrical function 🔒 Secure Door Locking – Ensures dishwasher runs only when door is properly closed ⚙️ Fixes Start Issues – Resolves no-start or cycle interruption problems 🧩 Direct-Fit Design – Installs without modification 💰 Cost-Effective Repair – Affordable alternative to OEM door latches 📐 Product Specification Part Number: WD01X29878 Component Type: Dishwasher Door Latch Assembly Function: Door locking and safety interlock Mounting: Screw-mounted, plug-in harness Application: Dishwasher door safety system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the dishwasher or turn off the breaker before servicing to avoid electrical shock. Basic Steps: Disconnect dishwasher power. Remove the inner door panel screws. Locate and disconnect the old door latch assembly. Remove mounting screws and take out the latch. Install the new XPARTCO WD01X29878 latch. Reconnect wiring and reassemble the door panel. Restore power and test operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore secure dishwasher operation and prevent door-related errors — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

W11087376 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers:W11087376, W10917114, 4534143, AP6237961, PS12074533. California Residents only WARNING: California’s Proposition 65 

Read more less

(2 Pack) WD12X10304 Genuine GE OEM Rack End Cap Clip Replaces Part Number:  WD12X10304, 1556527, WD12X0344, WD12X344, WD30X97, AH2370502, EA2370502, OEM13454003, AP4484666, PS2370502. Description: This Rack Slide End Cap is a Genuine OEM part for specific GE dishwasher models. This small but essential component is designed to secure the end of the rack slide rail, preventing the dish racks from sliding off the track or becoming misaligned.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link The WD14X10009 is a Genuine OEM GE replacement dishwasher hinge arm link compatible with an exceptionally wide range of GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers — it fits over 2,100 models. The hinge arm link is the small plastic connector that joins the door spring to the door hinge arm at the bottom of the dishwasher door. This tiny part carries a big load: it's what allows the spring to counterbalance the weight of the door — especially when the door is open with a fully loaded lower rack resting on it. Without an intact link, the spring can't do its job, and the door drops open under its own weight instead of lowering in a smooth, controlled motion. The hinge arm link is a small piece of white plastic approximately 1-1/2" long, weighing about 0.01 lbs. It fails from ordinary wear and tear — thousands of open/close cycles gradually stress the plastic until it cracks or snaps. As a Genuine OEM part manufactured by GE to factory specifications, the WD14X10009 directly replaces AP2039321, 270839, AH259336, EA259336, and PS259336. Important: your dishwasher has a door spring and hinge arm link on BOTH the left and right sides. This part is sold individually — if one link has broken from age, the other is the same age and often not far behind, so many customers order two and replace both while the dishwasher is pulled out. Installs in 15–30 minutes with basic hand tools. Quick Answer The WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link fixes GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore dishwashers where the door falls open instead of lowering gently, the door won't stay shut or won't latch, the door is hard to open or close, or the door slants when open. Small white plastic link ~1-1/2" long — connects the door spring to the door hinge arm. Genuine OEM. Sold individually. Replaces AP2039321, 270839, AH259336, EA259336, PS259336. Fits 2,100+ GE-platform dishwasher models. There's one link on EACH side of the door — consider ordering two. Common Problems This Part Fixes Dishwasher door falls open instead of lowering in a smooth, controlled motion — no counterbalance from the spring Door drops down hard when opened — link broken, spring disconnected Door won't stay shut, or opens unexpectedly Door won't latch or lock properly Door is difficult to open or close Door slants or hangs unevenly when open Hinge arm link visibly cracked, bent, broken, or significantly worn Broken plastic link found lying on the floor beneath the dishwasher Door spring disconnected and hanging loose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher hinge arm link directly replaces the following OEM and cross-reference part numbers: WD14X10009, AGE24269, AP2039321, 270839, AH259336, EA259336, EAP259336, PD00023035, PS259336 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hinge arm link is compatible with an exceptionally broad range of dishwashers — over 2,100 models across the following brands: GE dishwashers — the vast majority of GE dishwasher models across many generations GE Profile dishwashers (including PDW-series models) Café dishwashers (select models) GE Monogram dishwashers (select models) Hotpoint dishwashers (select models) RCA dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Kenmore / Sears dishwashers (select GE-built models) Important — There Are TWO Links, One Per Side: Your dishwasher door has a spring and hinge arm link on both the left and right sides. This part is sold individually. Many customers discover the second link only after reinstalling the dishwasher — and since both links are the same age and have seen the same wear, the surviving one often breaks soon after. Consider ordering two and replacing both while the dishwasher is already pulled out. Also inspect the door hinge cable at the same time; if it's frayed, kinked, or bent, replace it too. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Hinge arm link — connects the door spring to the door hinge arm, allowing the spring to counterbalance the door's weight Enables the dishwasher door to open in a smooth, controlled motion rather than dropping open Supports the door's weight even when the lower rack is fully loaded and resting on the open door Prevents strain on the door hinges and door misalignment Small white plastic link, approximately 1-1/2" long, ~0.01 lbs Sold individually — note there is one link on each side of the door Replaces AP2039321, 270839, AH259336, EA259336, and PS259336 Fits over 2,100 dishwasher models across GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built lines Inexpensive fix for a problem that would otherwise cost a service call — many customers report the entire repair takes about 15 minutes DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number WD14X10009 Part Type Dishwasher Hinge Arm Link (Door Spring Link) Condition Genuine OEM Application Dishwashers (GE platform) Length Approximately 1-1/2" Weight Approximately 0.01 lbs Color White Material Plastic Function Connects the door spring to the door hinge arm Location Bottom of the dishwasher door hinge, both left and right sides Quantity Sold individually (dishwasher uses TWO — one per side) Model Coverage Over 2,100 models Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. Remove the screws holding the bottom kick plate (a nut driver works well here) and the anchor screws at the top of the dishwasher that secure it to the countertop. Carefully pull the dishwasher out 8–10 inches from the cabinet to expose the door springs and hinge arm links at the bottom on both sides. (Depending on how the dishwasher is plumbed, you may be able to do this without disconnecting the water supply, drain line, or electrical — pull only as far as the connections allow, and disconnect them only if necessary for access.) Look at the hinge assembly at the bottom of the door: you'll see a steel cable with a hooked end, a spring, and the small white plastic link that ties them together. If the link is broken, it may already be lying on the floor. Remove the old link by disconnecting it from the hinge and spring — if it's cracked but still in place, you can break the remaining pieces free. Install the new WD14X10009: place the hinge arm link into the spring, hook the spring onto the clip, and seat the link into the clip on the hinge arm. Note: on some models the crimped hook opening on the steel cable is tight — if the new link won't slide in easily, a small file can carefully open the hook opening enough to accept it. Check the other side of the door while you're in there — there's a second spring and link, and if it's aged or cracked, replace it now. Push the dishwasher back into place, reinstall the anchor screws and kick plate, restore power and water, and test the door: it should now lower smoothly under spring tension rather than falling open. Tools needed: Nut driver, Phillips screwdriver, small file (occasionally), work gloves. Frequently Asked Questions My dishwasher door falls open instead of lowering gently — is this the part? Almost certainly, yes. The door spring is what counterbalances the door's weight so it lowers in a controlled motion. The hinge arm link is the small plastic piece that connects that spring to the door hinge arm. When the link cracks or snaps, the spring is effectively disconnected — so the door has no counterbalance and drops open under its own weight. This is the classic symptom. To confirm, pull the dishwasher out a few inches and look at the bottom hinge area on each side: if a link is broken, you'll often find the pieces on the floor or the spring hanging loose. If both links are intact, check the door hinge cable for fraying or the spring for damage. Should I order one or two? Order two. Your dishwasher has a door spring and hinge arm link on both sides of the door — and this part is sold individually. Many customers order one, replace the broken link, push the dishwasher back into the cabinet, and only then realize the second link exists (and is the same age, with the same wear). Since the tedious part of the job is pulling the dishwasher out from under the counter, replacing both links while you're already in there is the smart move. At a few dollars each, having a spare on hand is cheap insurance against doing the whole job over in a few months. Why do these little plastic links break? Ordinary wear and tear. The hinge arm link is a small plastic component that carries a surprising amount of load — every time you open the door, it transmits the spring's counterbalancing force to the hinge arm, and that load increases dramatically when the lower rack is fully loaded and resting on the open door. Over thousands of open/close cycles across years of use, the plastic fatigues and eventually cracks or snaps. It's a consumable wear item on GE dishwashers, which is exactly why GE uses the same inexpensive part across 2,100+ models. Do I have to disconnect the water and electrical to pull the dishwasher out? Often not. Many customers find that removing the top anchor screws and the bottom kick plate, then sliding the dishwasher out 8–10 inches, gives enough access to reach the hinge arm links — without disconnecting the water supply, drain hose, or electrical. It depends on how much slack your installer left in those lines. Pull the dishwasher out only as far as the connections allow, and see whether you can reach the hinge area. If the lines are too short and you can't reach, you'll need to disconnect the water supply, drain tube, and electrical (turn off power and water first). Either way, the link replacement itself takes only a few minutes once you can reach it. Should I replace the door hinge cable at the same time? Inspect it, and replace it if it shows any damage. The door hinge cable is the steel cable that connects the door spring assembly to the door hinge — it works alongside the link and spring in the same counterbalance system. If the cable is frayed, kinked, bent, or its crimped hook end is damaged, it will fail soon and you'll be pulling the dishwasher out again. Since you already have access, this is the ideal moment to check it. Also inspect the door spring itself for stretching or breakage. Contact our support team with your model number if you need the correct cable or spring part number. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same hinge arm link installed in compatible GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor The WPW10348269 is a genuine Whirlpool OEM drain pump motor for Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers. This pump uses an electric motor to create suction, pulling wastewater out of the tub and expelling it through the drain hose at the end of each cycle. This is the dedicated drain pump, distinct from a circulation pump — such as our WPW10605057 listing — which handles spraying water through the spray arms during the wash itself rather than draining it afterward. Rated 120VAC, 60Hz, 45W, 0.7A, with a run time pattern of 5 minutes on, 30 minutes off. Ships as a complete pump motor with impeller and O-ring. If the impeller becomes damaged or the motor shorts out and stops draining, the pump body itself can crack over time, leading to leakage — replacing the pump before that happens is the more reliable fix. Symptoms of a failing drain pump include water not draining from the tub, unusual noise such as grinding during the drain phase, or visible leaks from underneath the unit. It directly replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Quick Answer The WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor fixes Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers that aren't draining, are making grinding noise during the drain phase, or are leaking from underneath. 120VAC, 60Hz, 45W, 0.7A. Includes impeller and O-ring. Replaces W10348269, WPW10348269VP, W10084573, W10158351, 661662, 8558995, 8565839, 2813258, AP6020066, EAP11753379, PD00004898, PS11753379. This is the drain pump — a separate part from our WPW10605057 circulation pump listing, which handles spraying water rather than draining it. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Grinding noise coming from the drain pump area Water leaking from underneath the dishwasher Cycle stalling or failing to advance past the drain step Dishes not getting cleaned as a downstream effect of drainage problems Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: WPW10348269, W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Whirlpool dishwashers, and also fits select KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers built on the Whirlpool platform. Note — drain pump, not circulation pump: This is the dedicated drain pump, which removes wastewater from the tub. It is a separate part from our WPW10605057 listing, which is the circulation pump and diverter motor responsible for spraying water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified motor and impeller design Pumps wastewater out of the tub through the drain hose Resolves "not draining," "grinding noise," and "leaking underneath" symptoms caused by pump failure Complete assembly — includes pump motor, impeller, and O-ring Rated 120VAC, 60Hz, 45W, 0.7A Run time: 5 minutes on, 30 minutes off Dimensions: approximately 3-1/2"L x 3"W x 3-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10348269 Part Type Dishwasher Drain Pump Motor (with Impeller and O-Ring) Condition Genuine OEM Brand Whirlpool Function Pumps wastewater out of the tub through the drain hose Voltage 120VAC Frequency 60 Hz Wattage 45 W Amperage 0.7 A Run Time 5 min ON / 30 min OFF Dimensions Approx. 3-1/2"L x 3"W x 3-1/2"H Color White / Gray / Black / Yellow Related Part WPW10605057 circulation pump & diverter motor (different function, sold separately) Repair Difficulty Beginner to Moderate Quantity 1 drain pump motor Compatible Brands Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, Roper Installation Notes ⚠️ Unplug Dishwasher Before Starting — Removing The Unit Makes Access Easier Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This repair can be done without pulling the dishwasher out from under the counter, but many technicians find it considerably easier to access the pump if you do pull the unit out first. Remove the lower rack and any components blocking access to the tub floor, then work from underneath the dishwasher to reach the drain pump. Test the old pump for continuity with a multimeter before removing it — if it shows no continuity, or if it's getting power but still won't run, that confirms the pump has failed. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connection from the old pump, remove its mounting hardware, and pull it free. Install the new WPW10348269 in the same position, reconnect the drain hose connection securely, and reconnect the electrical connector fully. Reinstall any components removed for access and the lower rack. Restore power, run a test cycle, and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, 5/16" nut driver, 5/8" wrench, flathead screwdriver, multimeter, work gloves. Frequently Asked Questions Do I need to pull the dishwasher out from under the counter for this repair? Not strictly — this pump can be replaced without fully removing the dishwasher. That said, several customers who've done this repair note that pulling the unit out first makes access considerably easier, since you're working from underneath the appliance either way. If you have the space to pull it out, it's worth doing to make the job smoother. How do I know if the pump has actually failed? Test the pump motor with a multimeter set to continuity before replacing it. If there's no continuity, or if the pump is receiving power but still won't run, that confirms the motor has failed and the pump should be replaced. This quick check avoids replacing a part that isn't actually the problem. My old pump was leaking. Why does that happen? If the impeller becomes damaged or the motor shorts out and stops running, the pump body itself can develop a crack over time, which leads to leakage. Rather than trying to repair a leaking pump, replacing the complete assembly resolves both the drainage failure and the leak at the same time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original motor, impeller, and hose connection configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less