Search results for "drum bearings"

EXP641 Dryer Belt and Idler Pulley Set – Replaces WP40111201 & WPY54414 – Compatible with Maytag, Whirlpool & Kenmore Dryers Product Description Restore smooth drum rotation and eliminate dryer noise with the EXP641 Dryer Belt and Idler Pulley Set. This high-quality aftermarket repair kit includes a dryer drum belt and idler pulley wheel, providing a complete solution for common belt tension and tumbling issues. If your dryer is squealing, not turning, or producing uneven drying results, worn belt and pulley components are often the cause. Replacing both parts together helps restore proper belt tension, reduce noise, and extend the life of your dryer. This kit is engineered to match original fit and function while offering a cost-effective alternative to OEM parts. Belt Replaces Part Numbers WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, AP6009126, AWP47792, EAP11742271, PD00002505, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115 Idler Pulley Replaces Part Numbers WPY54414, Y54414, 1246423, 14218926, 54414, R0609504, 54414-2, PD00002420, EAP11757553, AP6024203, PS11757553. Compatibility This dryer belt and idler pulley repair kit fits select Maytag, Whirlpool, Kenmore (Whirlpool/Maytag-manufactured), Amana, Crosley, and Estate dryers. Common compatible models include (but are not limited to): Maytag MEDC215EW Whirlpool WED4815EW Kenmore 110.60612990 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. Key Features Complete Repair Kit – Includes drum belt and idler pulley wheel Restores Smooth Tumbling – Ensures proper drum rotation Reduces Noise & Vibration – Fixes squealing or slipping belt issues Durable Construction – Reinforced belt and long-life pulley bearing Cost-Effective Solution – Replace both wear items at once Product Specification Kit Number: EXP641 Includes: Dryer Drum Belt (replaces WP40111201) Idler Pulley Wheel (replaces WPY54414) Application: Dryer drum drive system Material: Reinforced rubber belt, metal pulley with bearing Quality Level: Aftermarket replacement kit (not OEM) Installation Notes Tools Needed: Phillips screwdriver, nut driver Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove top and front panels (model dependent). Remove drum and old belt and pulley. Install new idler pulley onto idler arm. Route new belt around drum and motor pulley. Reassemble dryer and test operation. Time Required: 30–45 minutes Shop With Confidence Trusted Aftermarket Appliance Parts 30-Day Return Policy Restore quiet, reliable dryer performance — Add to Cart Now for a complete, budget-friendly repair solution!

Read more less

WE03X10016 Dryer Genuine OEM Drum Roller Assembly – Compatible with GE & Hotpoint Dryers Product Description Restore smooth, quiet dryer operation with the WE03X10016 Dryer Genuine OEM Drum Roller Assembly. This factory-approved roller supports the dryer drum as it rotates, reducing friction and vibration during operation. A worn or damaged drum roller can cause squealing, thumping, grinding noises, or uneven tumbling. Replacing it with this Genuine OEM assembly ensures proper drum alignment, quiet performance, and long-lasting reliability. Replaces Part Numbers WE03X10016, WE01X10384, WE12M39, WE01X10385, WE01X10386, 3029206, PD00042055, EAP8756654, AP5793315, PS8756654. Compatibility This Genuine OEM drum roller assembly fits select GE and Hotpoint dryers. Example compatible models include (but are not limited to):GE GTD33EASK0WW, GTD42EASJ2WW, GTD45EASJ2WSHotpoint HTDX100EM8WW, HTDX100ED6WW Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and smooth rotation 🔇 Noise Reduction – Helps eliminate squealing, thumping, and grinding sounds ⚙️ Stable Drum Support – Maintains proper drum alignment during all cycles 💪 Durable Construction – OEM-grade materials designed for long service life 🛡️ Fixes Common Issues – Resolves noisy operation, drum drag, or uneven tumbling 📐 Product Specification Part Number: WE03X10016 Component Type: Dryer Drum Roller Assembly Material: OEM-grade polymer roller with metal shaft insert Mounting: Slides onto support shaft and secures with retaining clip Location: Rear drum support (varies by model) Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect power and remove the dryer front panel and drum as required. Locate the worn drum roller on the rear support shaft. Remove the retaining clip and slide off the old roller assembly. Install the new WE03X10016 roller assembly and secure it with the clip. Reinstall the drum and panels, then restore power. Run a test cycle to confirm quiet, smooth operation. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore quiet, smooth dryer performance — Add to Cart Now for a factory-quality repair!

Read more less

XPARTCO WE12X10009 Dryer Drum Belt The XPARTCO WE12X10009 is an aftermarket replacement drum drive belt for GE and Hotpoint electric and gas dryers, including washer-dryer combos. The belt wraps around the drum and runs over the motor pulley and idler pulley, so the motor can turn the drum. A worn, stretched, or broken belt can cause a thumping or squealing noise, a drum that turns slowly, or a drum that won't turn at all. This is a direct-fit aftermarket replacement for the original GE belt. Because the drum has to be moved to fit a new belt, it is also a good time to inspect the idler pulley, the drum glides, and the rear bearing and replace any that look worn. Quick Answer The XPARTCO WE12X10009 Drum Belt fixes a GE or Hotpoint dryer whose drum won't turn, turns slowly, or makes a thumping or squealing noise. If the motor hums or runs but the drum stays still, a broken belt is the usual cause. Classic symptom: the dryer starts and the motor runs, but the drum doesn't turn, and you may hear a thump or squeal before it quits. Common Problems This Part Fixes Drum does not turn although the motor runs Thumping or squealing noise while the drum turns Drum turns slowly or intermittently Dryer starts but clothes don't tumble Visible fraying, cracking, or a snapped belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part numbers: WE12X10009, WE12X0090, WE12X10001, WE12X10010, WE12X90, AGE25019, AH959964, AP3204994, EA959964, EAP959964, PD00001333, PS959964 These numbers span several generations of GE's own part numbering for this belt. GE's catalog lists WE12X0090 as superseded to WE12X10009. Confirm against your dryer's parts diagram if your model calls out a different number. Compatibility This drum belt is listed for GE and Hotpoint electric and gas dryers and washer-dryer combos, including these examples: DBL333EA0AA, DBL333EB0WW, DBL333EB1WW (electric) DBL333GA0AA, DBL333GB1CC, DBL333GB1WW (gas) Note: The models above are a sample of roughly 30 listed GE models, not a full list. Drum belts differ between dryer families, so check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket drum drive belt for GE and Hotpoint dryers Turns the drum from the motor pulley Fits electric and gas models, including washer-dryer combos Resolves drum-not-turning and belt noise problems Straightforward repair, typically 30 minutes to 1 hour Product Specifications Part Number XPWE12X10009 OEM Part Number WE12X10009 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application GE & Hotpoint Dryers and Washer-Dryer Combos Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the top and front panel as shown in your model's service guide, then slide the drum out, which is easier with a second person. Remove the old belt, loop the new belt around the drum, route it over the idler and motor pulleys, and reassemble in reverse order. Check the idler pulley and drum glides while the drum is out and replace any that are worn. Frequently Asked Questions My dryer runs but the drum won't turn. Is this the part I need? That is the classic sign of a broken or slipped drum belt. If the motor runs and you can turn the drum freely by hand, check the belt first. What's the difference between WE12X10009 and WE12X0090? GE's catalog lists WE12X0090 as superseded to WE12X10009. This belt covers both numbers, along with the other numbers in the Replaces list above. Should I replace anything else while the drum is out? Inspect the idler pulley, the drum glides, and the rear drum bearing. These wear along with the belt, and they are much easier to replace now than later. Will this fit my dryer? It is listed for many GE and Hotpoint dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool WP37001042 Dryer Drum Roller - Compatible with Admiral, Amana, Magic Chef, Maytag, Speed Queen Product Description Restore smooth and quiet operation to your dryer with the Genuine Whirlpool WP37001042 Dryer Drum Roller. This OEM drum roller is designed for select Admiral, Amana, Magic Chef, Maytag, and Speed Queen dryers, supporting the drum for even tumbling and efficient drying. Made of durable rubber, metal, and plastic, it ensures long-lasting performance, addressing issues like loud rumbling, squeaking, or uneven drum movement. Note: Includes one drum roller. Disconnect power and gas (if applicable) before installation. For even wear, replace all rollers at the same time. Replaces part numbers: WP37001042, 37001042, 14218934, 500214, 500214P, WP37001042VP, 5-0214, 500214P-REPL, 500214-REPL,37001042-REPL, 500214P, 500214, PD00002495, EAP11741913, AP6008773, PS11741913. Compatibility: Compatible with models including but not limited to: Admiral: ADE7005AKW, ADE7005AYW, ADE9005AGW, ADG7005AWW Amana: AEM197, AEM377, AEM397, AEM407L, AEM407W, ALE120RAW, ALE230RAW Maytag: MDE3706AGW, MDG2706AGW Speed Queen: AGM199, AGM379, AGM399 Bosch, Crosley, Danby, Kenmore, Magic Chef: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Admiral, Amana, Magic Chef, Maytag, and Speed Queen dryers. 🔄 Specifications: OEM drum roller made of rubber, metal, and plastic for smooth drum rotation. 💪 Reliable Performance: Authentic Whirlpool part ensures superior durability and performance. 🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves loud rumbling, squeaking, or uneven drum movement. Product Specification Part Number: Genuine Whirlpool WP37001042 Component Type: Dryer drum roller Material: Rubber, metal, plastic Mounting: Bolt-mounted to dryer drum assembly Operating Conditions: Suitable for household and commercial dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

W11568627 Genuine OEM Whirlpool/Kenmore Dryer Drum Belt The W11568627 is a genuine OEM drum (cylinder) belt for select Whirlpool and Kenmore front-load dryers. This belt wraps around the outside of the drum and routes around the drive motor pulley and idler pulley — it's what actually spins the drum during a drying cycle while the motor and blower keep running independently. Over time this belt stretches, glazes, or cracks from heat and friction, and it eventually slips or snaps, leaving the drum motionless even though the rest of the dryer still runs. Manufactured by Whirlpool to factory spec for smooth, durable drum operation under high-demand drying cycles, this is a genuine OEM part — not an aftermarket equivalent — so fit and long-term performance match what came on the dryer originally. Quick Answer The Genuine OEM W11568627 Dryer Drum Belt fixes a Whirlpool or Kenmore dryer whose drum won't spin, or that runs with a rubbing/thumping noise from the drum area. Genuine OEM replacement, factory fit. Classic symptom: motor and airflow run normally, but the drum sits still — or a rubbing sound right before the belt fails completely. Common Problems This Part Fixes Dryer runs (motor and airflow work) but the drum doesn't spin Rubbing, squealing, or thumping noise from inside the dryer during operation Clothes bunch up in one spot instead of tumbling Burning rubber smell from a slipping or overheating belt Visible cracking, glazing, or fraying on the old belt Dryer drum spins freely by hand with no resistance from the motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part number: W11568627, W10577771, AP7175918, AWP45299, EAP16660508, OEM21527763, PD00070745, PS16660508 W10577771 is the previous Whirlpool part number for this belt; W11568627 is the current production number. We were not able to confirm additional cross-reference numbers beyond these two at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with the following Whirlpool and Kenmore dryer models: 11061632610, 11061632611 11061633610, 11061633611, 11061633612 11071632610, 11071633610, 110C61633610 WED9500EC0, WED9500EW0, WGD9500EC0, WGD9500EW0 Note: Not all applicable models are necessarily listed above — this is the compatibility data we were able to confirm from available sourcing, and Whirlpool may use this belt on additional models not shown here. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering. Key Features Genuine OEM drum belt — factory fit and durability, not an aftermarket equivalent Drives drum rotation during the drying cycle Built for smooth, reliable operation under high-demand drying cycles Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms Direct replacement for both W11568627 and the earlier W10577771 numbering One-year manufacturer replacement warranty on genuine parts Product Specifications Part Number W11568627 OEM Part Number W11568627 Part Type Dryer Drum (Cylinder) Belt Condition Genuine OEM Application Whirlpool & Kenmore Dryers Country of Origin Mexico Installation Notes ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's front or rear access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel. Frequently Asked Questions My dryer runs but the drum won't turn — is this the part I need? Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless. Is W10577771 the same belt as W11568627? Yes. W10577771 was the earlier Whirlpool part number for this belt; W11568627 is the current production number for the same design. If your dryer's parts diagram shows W10577771, this part is the correct current replacement. My exact model isn't listed — will this still fit? Possibly. Whirlpool uses this belt across a range of models beyond what's confirmed in our current compatibility data. Contact our support team with your full model number and we'll verify fit before you order. Do I need to replace the idler pulley at the same time? Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10547292 Genuine OEM Whirlpool Dryer Idler Pulley The WPW10547292 is a genuine Whirlpool OEM idler pulley assembly for Whirlpool, Maytag, and Kenmore dryers. This pulley sits to the left of the motor, just below the drum belt, and its job is to ride against the belt and keep constant tension on it as the motor turns — without that tension, the belt would sag, slip on the motor pulley, and fail to reliably turn the drum. The pulley wheel itself spins freely on a bearing mounted to a bracket, so as the belt moves, the pulley spins along with it under light load. Over time, the bearing inside the pulley wheel wears out, causing it to spin roughly, seize partially, or bind up entirely instead of turning freely. When that happens, the belt drags against a pulley that should be spinning smoothly with it, generating friction, heat, and noise. A worn idler pulley produces a very recognizable symptom: a persistent squeaking or squealing sound during operation that often gets more noticeable over time, and in more advanced cases, a drum that struggles to spin or doesn't spin at all, or a burning smell as the seized pulley drags against the belt. It directly replaces W10547292, WPW10547292VP, AP6022817, 8547160, PS11756154, and LP16246. Quick Answer The WPW10547292 Genuine OEM Whirlpool Dryer Idler Pulley fixes Whirlpool, Maytag, and Kenmore dryers with a persistent squeaking or squealing noise during operation, a drum that struggles to spin, or a burning smell from a seized pulley dragging against the belt. Mounts to the left of the motor, below the belt. Replaces W10547292, WPW10547292VP, AP6022817, 8547160, PS11756154, LP16246. Consider replacing the drum belt (8544742/WP8544742) at the same time — a seized idler pulley is a common cause of premature belt wear, and you'll already have the cabinet open. Common Problems This Part Fixes Persistent squeaking or squealing noise during operation Noise that gradually gets louder or more frequent over time Drum that struggles to spin, spins intermittently, or won't spin at all Burning smell coming from inside the dryer cabinet Pulley wheel that feels stiff, gritty, or seized when checked by hand Drive belt showing premature wear or fraying from dragging against a bound-up pulley Noise that stops and starts depending on drum rotation or load size Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer idler pulley directly replaces the following OEM and cross-reference part numbers: WPW10547292, W10547292, WPW10547292VP, AP6022817, 8547160, EAP11756154, PS11756154, AWP50878, PD00003590, LP16246 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select Whirlpool, Maytag, and Kenmore dryers, including model numbers such as: Whirlpool: WED7300XW0, WED7800XB0, WED8100BW0, WED8500BC0, WED8500BR0, WED8500BW0, WED8600YW0, WED8600YW1, 7MWGD7800XW0, 7MWGD8800AW0, 7MWGD8800AW1 Whirlpool (Y-prefix): YWED8000BW0, YWED8100BW0, YWED8200YW2, YWED8400YW2, YWED8500BC0, YWED8500BW0, YWED8800YC2, YWED8800YW2, YWED8900BC0, YWED8900BW0, YMEDB980BW0 Maytag: 7MMGDB850WL0, 7MMGDB950AG0, MEDB200VQ1, MEDB725BW0, MEDB800VB0, MEDB850WL1, MEDB850WR1 Kenmore: 110.78102310, 11067032600, 11067032601, 11067042600, 11067042601, 11067052600, 11067062600, 11067072600, 11067082600, 11067086600 Note: Whirlpool uses several different idler pulley designs across its dryer lineup, and they are NOT interchangeable. This WPW10547292 pulley is a separate part from the W10837240 pulley (used on Cabrio, Duet, and Bravos XL platforms) and the 279640 pulley (an older, differently-shaped design). Fitting the wrong pulley can result in a bracket that doesn't mount correctly or a wheel that doesn't align with your belt. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pulley fits your dryer. Key Features Genuine Whirlpool OEM part — factory-specified bearing and bracket design Maintains constant tension on the drive belt so it can turn the drum smoothly Resolves "squeaking or squealing noise," "drum won't spin," and "burning smell" symptoms caused by a worn or seized pulley bearing Complete wheel-and-bracket assembly — no need to source parts separately Direct drop-in replacement — mounts to the original bracket position with the same bolt Replaces W10547292, WPW10547292VP, AP6022817, 8547160, PS11756154, and LP16246 Compatible with Whirlpool, Maytag, and Kenmore dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10547292 Part Type Dryer Idler Pulley Assembly (Wheel + Bracket) Condition Genuine OEM Brand Whirlpool Location Left of the motor, below the drum belt Function Maintains tension on the drive belt as it turns the drum Fuel Type Electric and gas dryers Companion Part 8544742 / WP8544742 drum belt (check/replace if pulley failed) Repair Difficulty Medium — requires some disassembly Quantity 1 idler pulley assembly Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — On Gas Models, Shut Off The Gas Supply Too Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas dryer, also close the gas shutoff valve before moving the cabinet. Wear work gloves. Remove the lint filter, then remove the screws along the top edge of the front panel and take the panel off. With the front open, locate the belt tensioner pulley — it sits to the left of the motor, just below the belt. Use a socket wrench with an extension to loosen the pulley's mounting bolt, then remove the old pulley assembly, releasing the belt from it as you go. Slide the new WPW10547292 assembly onto the mounting post, making sure the grooves line up correctly so the belt seats snugly against the wheel, then re-tighten the mounting bolt securely. Before closing everything up, spin the new pulley by hand to confirm it turns freely with no grinding or resistance, and inspect the belt for wear, glazing, or fraying — replace it as well if it shows any of these signs, since a worn belt will quickly wear out even a brand-new pulley. Reinstall the front panel and its screws, restore power, and run a short empty cycle listening for the squeak to confirm it's resolved. Tools needed: 1/4" nut driver, 3/8" socket wrench with extension, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer squeaks constantly. Is this definitely the idler pulley? It's one of the most common causes of a persistent squeak, especially if the noise is steady and present throughout the cycle rather than only at certain moments. The pulley's internal bearing wears out over years of use, and a worn bearing produces exactly this kind of ongoing squeal as it spins roughly instead of smoothly. If you can access the pulley and spin it by hand, feeling any grinding or stiffness confirms the diagnosis. Is this a hard repair, or can I do it myself? It's a moderate repair — you'll need to remove the front panel and access the area behind the motor, which some customers describe as needing to "pull the entire dryer apart" to reach the pulley. It's very doable with basic hand tools and some patience, but budget more time than a simple part swap, and expect to use a socket wrench with an extension to reach the mounting bolt in that tighter space. Should I replace the belt while I'm already in there? It's worth strongly considering. A seized or dragging pulley puts extra wear on the belt, so if your pulley failed from being seized rather than just noisy, the belt may already be showing damage. Since you'll already have the cabinet open and the belt exposed, inspecting it — and replacing it if it shows glazing, cracking, or fraying — saves you from repeating this same teardown again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original bearing design, bracket shape, and mounting configuration of the idler pulley assembly originally installed in your Whirlpool, Maytag, or Kenmore dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-16782A Dryer Drum Roller The XPARTCO DC97-16782A is an aftermarket replacement drum support roller compatible with select Samsung and Kenmore dryers. The drum roller is a rear support wheel that cradles the dryer drum and allows it to rotate smoothly during every drying cycle. Over time, the rollers wear down, causing the drum to wobble, squeak, or thump during operation — replacing them restores quiet, stable drum rotation. This roller features a self-lubricating bushing and includes the roller shaft and mounting tri-ring clips for a complete, ready-to-install assembly. It measures approximately 3-1/4 inches in diameter and directly replaces OEM part numbers DC97-16782A, DC97-07523A, and DC97-07523B. Sold individually — most Samsung dryers use two rear drum rollers, so we recommend replacing both at the same time. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC97-16782A Dryer Drum Roller fixes squeaking, thumping, or rumbling noises coming from Samsung and Kenmore dryers during operation. The drum roller supports the rear of the dryer drum — when worn, it causes noise and uneven drum rotation. Includes roller shaft and mounting clips. Approximately 3-1/4" diameter. Compatible with select Samsung and Kenmore dryers. Common Problems This Part Fixes Loud squeaking, thumping, or rumbling noise during dryer operation Drum wobbling or vibrating excessively during the drying cycle Grinding or scraping sound as the drum rotates Dryer making noise that gets worse over time Visible flat spots, cracks, or worn surfaces on existing drum rollers Drum not rotating smoothly or spinning unevenly Replaces Part Numbers This drum roller directly replaces the following OEM and cross-reference part numbers: DC97-16782A, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PD00002021, EAP4221885, AP5325135, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, ASM930889, PD00003650, EAP11749648, AP6016361, PS11749648. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum roller is compatible with select dryers from the following brands: Samsung dryers (gas and electric — DV2, DV3, DV4, DV5, DVE, DVG series) Kenmore / Sears dryers (select models built on Samsung platform) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Supports the rear of the dryer drum for smooth, stable, quiet rotation during every cycle Approximately 3-1/4" diameter — direct replacement for OEM DC97-16782A, DC97-07523A, and DC97-07523B Self-lubricating bushing — no additional grease or oil required after installation Complete assembly includes roller shaft and mounting tri-ring clips — everything needed for installation Durable rubber and metal construction — resists wear, cracking, and heat damage Aftermarket replacement built to OEM-equivalent quality standards Often replaced together with the drum belt (6602-001655) and idler pulley (DC93-00634A) for a complete drum drive repair DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number DC97-16782A Part Type Dryer Drum Support Roller Condition Aftermarket Replacement Application Gas and Electric Dryers Diameter Approximately 3-1/4 inches Dimensions 3" L x 2-1/2" W x 3" H Material Rubber / Plastic / Metal Lubrication Self-lubricating bushing (no grease needed) Includes Roller, shaft, and mounting tri-ring clips Sold As Single roller (most dryers require 2 — replace both) Compatible Brands Samsung, Kenmore Often Replaced With 6602-001655 Drum Belt, DC93-00634A Idler Pulley Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum rollers, remove the top panel and front panel of the dryer, then release the drum belt tension at the idler pulley and lift the drum out of the cabinet. The two rear drum rollers are located on the rear bulkhead. Remove the mounting clip, slide the old roller off the shaft, and install the new DC97-16782A roller — the shaft thread is clockwise. Reinstall the mounting clip to secure the roller. Replace both rear rollers at the same time even if only one appears worn. Reassemble the dryer, restore power, and run a test cycle. Tip: While the drum is out, inspect and replace the drum belt (6602-001655) and idler pulley (DC93-00634A) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How many drum rollers does my Samsung dryer need? Most Samsung dryers have two rear drum support rollers. This listing is for a single roller. We strongly recommend replacing both rollers at the same time — even if only one appears damaged — since they wear at the same rate and replacing both prevents the need to disassemble the dryer again soon after. What does the drum roller do? The drum rollers are support wheels mounted on the rear bulkhead of the dryer. They cradle the back edge of the dryer drum and allow it to spin smoothly during operation. When the rollers wear down or develop flat spots, the drum wobbles and creates loud squeaking, thumping, or grinding noises. Does DC97-16782A replace DC97-07523A and DC97-07523B? Yes. The DC97-16782A is the updated part number that directly supersedes both DC97-07523A and DC97-07523B. If your dryer originally used either of those older part numbers, the DC97-16782A is the correct current replacement. Should I also replace the drum belt and idler pulley at the same time? Yes — since the dryer is already fully disassembled to replace the rollers, it is highly recommended to also inspect and replace the drum belt (6602-001655) and idler pulley (DC93-00634A) at the same time. These three parts wear together and are commonly sold as a dryer repair kit, saving you from having to take the dryer apart again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is made from durable rubber, plastic, and metal to match the dimensions and performance of the original DC97-16782A roller. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 691366 Dryer Idler Pulley Assembly Replaces WP691366 The XPARTCO 691366 is an aftermarket replacement dryer idler pulley assembly compatible with a wide range of Whirlpool-family dryers — particularly models with the lint filter on top — including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef, and Norge. The idler pulley assembly is a spring-tensioned arm and wheel that presses against the drum drive belt to maintain correct belt tension as it wraps around the drum and motor pulley. Without proper tension, the belt slips off the motor pulley, causing the drum to stop spinning. A worn idler pulley bearing also causes squealing, squeaking, or thumping noises during operation. This is a complete idler arm and pulley assembly — it includes both the spring arm and the wheel, and mounts directly to the existing bracket in the dryer. Overall dimensions are 6"L x 1-5/8"W x 3-7/8"H with a 1-7/8" diameter pulley wheel. It replaces older Teflon friction-style idler pulleys and provides a smoother, longer-lasting ball-bearing wheel. It directly replaces WP691366, 691366, 239477, 337116, 337407, 3394332, 347034, 347226, 4319391, 688166, W10612905, AP6010582, PS11743765, and over 20 additional cross-reference numbers. Often replaced together with the drum belt (341241) and drum support rollers (349241T) as the 4392065 maintenance kit. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 691366 Dryer Idler Pulley Assembly fixes Whirlpool-family dryers that are squealing, thumping, or where the drum stops spinning because the belt has lost tension. Complete arm and pulley assembly. 6"L x 1-5/8"W x 3-7/8"H overall, 1-7/8" pulley diameter. Replaces older Teflon friction pulleys with ball-bearing wheel. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, and more. Replaces WP691366, 239477, 337116, 3394332, 347034, AP6010582, PS11743765. Often replaced with 341241 belt and 349241T rollers. Common Problems This Part Fixes Drum not spinning — belt has lost tension and slipped off the motor pulley Loud squealing or squeaking noise during the drying cycle — worn idler pulley bearing Thumping or clunking noise as the pulley wheel wobbles on a worn bearing Belt repeatedly slipping or falling off after being reinstalled Grinding noise from the idler pulley area — bearing fully failed Dryer drum spinning intermittently due to inconsistent belt tension Idler pulley arm visibly cracked, broken, or wheel no longer spinning freely Replaces Part Numbers This idler pulley assembly directly replaces the following OEM and cross-reference part numbers: WP691366, 691366, 239477, 26000691366, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, WP691366VP, AWP48059, EAP11743765, AP6010582, PD00002256, PS11743765. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley assembly is compatible with select gas and electric dryers from the following brands — particularly models with the lint filter on top: Whirlpool dryers (gas and electric — WED, WGD, LE, LG, and related series with top lint filter) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Norge dryers Note: The 691366 idler pulley is for older Whirlpool-family dryers with the lint filter on top. Newer Whirlpool dryers with the lint screen inside the door use the W10837240 idler pulley arm assembly instead. Always verify your model number before ordering. Key Features Complete idler arm and pulley assembly — includes both the spring-tensioned arm and the pulley wheel Maintains correct drive belt tension so the belt grips the drum and motor pulley without slipping Redesigned ball-bearing pulley wheel replaces older Teflon friction-style pulleys for longer service life and quieter operation Overall dimensions: 6"L x 1-5/8"W x 3-7/8"H; pulley wheel diameter: 1-7/8" Plastic arm with metal shaft and ball-bearing pulley wheel Replaces WP691366, 239477, 337116, 3394332, 347034, AP6010582, and over 30 additional cross-reference numbers Compatible with 12 major appliance brands on the Whirlpool top-lint-filter platform Often replaced together with the drum belt (341241) and drum rollers (349241T) — all three included in the 4392065 maintenance kit Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 691366 OEM Part Number WP691366 Part Type Dryer Idler Pulley Assembly (Arm and Wheel) Condition Aftermarket Replacement Application Gas and Electric Dryers (lint filter on top models) Overall Dimensions 6"L x 1-5/8"W x 3-7/8"H Pulley Wheel Diameter 1-7/8 inches Material Plastic arm / Metal shaft / Ball-bearing pulley wheel Color Black / White Includes Complete idler arm and pulley assembly Often Replaced With 341241 Drum Belt, 349241T Drum Rollers (4392065 kit) Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to fully access the drum drive components. Release belt tension by pushing the idler pulley arm toward the motor and sliding the belt off. Note how the belt is routed before removing — take a photo. Unclip or unscrew the old idler pulley assembly from its mounting bracket. Install the new 691366 idler pulley in the same position. Re-route the belt around the drum (ribbed side in), under the idler pulley, and around the motor pulley, then release the idler arm to create tension. Reassemble the front and top panels, restore power, and run a test cycle. Tip: while the dryer is open, inspect and replace the drum belt (341241) and drum support rollers (349241T) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife. Frequently Asked Questions What does the idler pulley do? The idler pulley is a spring-loaded arm and wheel assembly that presses against the drive belt between the drum and the motor pulley, keeping the belt under constant tension. This tension is what allows the belt to grip both the drum and the motor pulley without slipping as the motor spins. Without proper tension — or with a pulley bearing that has failed — the belt slips, the drum stops spinning, and the dryer produces heat but does not tumble clothes. A worn bearing also creates the high-pitched squealing sound that is the most common sign of idler pulley failure. What is the difference between 691366 and WP691366? These are the same idler pulley assembly. WP691366 is the updated Whirlpool OEM part number that superseded the original 691366. The W10612905 is also a cross-reference for the same assembly. This aftermarket replacement is compatible with all three numbers. What is the difference between 691366 and W10837240? Both are Whirlpool dryer idler pulley assemblies, but for different dryer generations. The 691366 (WP691366) is used on older Whirlpool-family dryers with the lint filter on top of the dryer. The W10837240 is a larger, redesigned idler arm and bracket assembly used on newer Whirlpool-family dryers with the lint screen inside the door. They are not interchangeable. Always verify your model number to confirm which idler pulley is correct for your dryer. Should I also replace the belt and drum rollers at the same time? Yes — since the dryer must be disassembled to replace the idler pulley, this is the ideal time to also inspect and replace the drum belt (341241) and rear drum support rollers (349241T). All three parts are part of the same drum drive system and wear at similar rates. The 4392065 maintenance kit includes all three together and is the recommended approach for a complete drum drive repair — one teardown covers everything. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with a ball-bearing pulley wheel to match the dimensions and performance of the original WP691366 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Y54414 Dryer Idler Pulley Replaces WPY54414 The Y54414 is a genuine Whirlpool OEM idler pulley wheel and bearing assembly for Whirlpool dryers, and also fits select Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen models. This pulley puts tension on the drive belt as it rides against it, and correct tension is what allows the belt to grip properly and spin the drum smoothly throughout the drying cycle. Available in beige or black, this pulley wheel is 2" wide with a metallic bearing at its center, and mounts beneath the drum using two 5/16" screws. Over time, the bearing wears out or the wheel becomes damaged, and once that happens, the pulley can no longer maintain proper belt tension. Symptoms of a failing idler pulley include the dryer making noise during operation, failing to start, or failing to tumble, even though other parts of the drying cycle — like heating — may continue working normally. It directly replaces WPY54414, WPY54414VP, 14218926, 54414, 54414-REPL, 54414-2, R0609504, R0609504-REPL, AP6024203, AP6329060, PS11757553, EAP11757553, PS17001032, D510142P, 510142P, and 510142. Quick Answer The Y54414 Dryer Idler Pulley fixes Whirlpool, Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen dryers making noise during operation, failing to start, or failing to tumble — even while other functions like heating still work. 2" pulley wheel with metallic bearing, beige or black. Replaces WPY54414, WPY54414VP, 14218926, 54414, 54414-REPL, 54414-2, R0609504, R0609504-REPL, AP6024203, AP6329060, PS11757553, EAP11757553, PS17001032, D510142P, 510142P, 510142. This pulley is located beneath the drum — removing the blower housing and motor first makes access considerably easier. Common Problems This Part Fixes Dryer making noise during operation Dryer fails to start Dryer fails to tumble Dryer dries clothes but makes a terrible or unusual noise while doing so Belt slipping or losing tension Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer idler pulley directly replaces the following OEM and cross-reference part numbers: WPY54414, Y54414, 14218926, 54414, R0609504, WPY54414VP, 54414-REPL, R0609504-REPL, AP6024203, AWP51465, EAP11757553, PD00002420, PS11757553, D510142P, 510142P, 510142, D510142, 510142P, 510142, 54414, 54415, 54415P, AP6329060, ASQ376005, PD00042476, PS17001032, DE407 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select Whirlpool dryers, and also fits select Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen dryers built on the Whirlpool platform, including model numbers such as SDG3606AWW, LG8469W2, SDE3606AYW, SDE4606AYW, SDG4606AWW, and LEA30AW. Note: This is a different idler pulley from our 279640 listing, used on other Whirlpool/Kenmore dryer models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pulley your dryer needs. Key Features Genuine Whirlpool OEM part — factory-specified pulley wheel and bearing design Maintains proper tension on the drive belt for smooth drum rotation Resolves "noisy operation," "won't start," and "won't tumble" symptoms caused by pulley failure 2" wide pulley wheel with metallic bearing Available in beige or black Mounts beneath the drum with two 5/16" screws Direct drop-in replacement matching the original mounting Replaces WPY54414, WPY54414VP, 14218926, 54414, 54414-REPL, 54414-2, R0609504, R0609504-REPL, AP6024203, AP6329060, PS11757553, EAP11757553, PS17001032, D510142P, 510142P, and 510142 Compatible with Whirlpool, Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number Y54414 OEM Part Number WPY54414 Part Type Dryer Idler Pulley Wheel & Bearing Assembly Condition Genuine OEM Color Beige or Black Wheel Width 2" Bearing Metallic, center-mounted Location Beneath the drum Mounting Two 5/16" screws Repair Difficulty Moderate — drum removal required for access Quantity 1 idler pulley Compatible Brands Whirlpool, Maytag, Amana, Caloric, Crosley, Kenmore, Speed Queen Installation Notes ⚠️ Unplug Dryer Before Starting — Remove The Blower Housing And Motor First For Easier Access Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This pulley is located beneath the drum, so the drum will need to be removed to access it. Per official guidance, it's also recommended to remove the blower housing and motor from the dryer for easier access to the idler pulley. With the drum out and access clear, locate the idler pulley and remove the two 5/16" screws securing it in place. Take out the old pulley. Install the new Y54414 in the same position, making sure it's seated correctly against where the belt will ride, and secure it with the two 5/16" screws. Reinstall the motor and blower housing if removed, then reinstall the drum. Reroute the drive belt around the drum, motor pulley, and this idler pulley, matching the original path. Reassemble any panels removed for access. Restore power and run a test cycle to confirm quiet, smooth tumbling with proper belt tension. Tools needed: 5/16" nut driver or socket, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer dries clothes fine but makes a terrible noise. Is this the part I need? Yes, this is a documented symptom of a worn idler pulley. One customer described exactly this: "The dryer would dry clothes but made a terrible noise" — after watching a repair video to identify the correct part, they confirmed this idler pulley was the cause, since a worn or damaged pulley can still allow the dryer to function while producing noticeable noise as it rubs or wobbles against the belt. Is there an easier way to access this pulley than pulling out the whole drum? The drum does need to come out since this pulley sits beneath it, but official guidance recommends also removing the blower housing and motor from the dryer, which makes reaching and working with the idler pulley considerably easier than trying to access it with those components still in place. My dryer won't start at all. Could this pulley really be the cause? Yes, on some models. If the idler pulley fails to put proper tension on the belt, some dryers won't allow the cycle to start at all rather than simply running without tumbling, since certain safety interlocks depend on normal belt tension and drum movement. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pulley wheel size, bearing type, and mounting configuration of the idler pulley originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4 Pack - XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703 The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement. Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more. Common Problems This Part Fixes Violent shaking or vibrating during the spin cycle Loud banging, thumping, or clunking noise during spin Washer "walking" across the floor during the spin cycle Outer tub hitting the sides of the cabinet during high-speed spin Spin cycle errors caused by excessive tub movement triggering the imbalance sensor Visible oil leak, broken mount, or collapsed shock absorber body Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration Replaces Part Numbers This shock absorber directly replaces the following OEM and cross-reference part numbers: WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — GHW and WFW series Maytag front-load washers — MHWE and MFW series Kenmore / Sears front-load washers (select Whirlpool-built models) KitchenAid front-load washers — KHWS series Amana front-load washers Jenn-Air front-load washers Admiral front-load washers Roper front-load washers Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after. Key Features Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life Direct replacement for WP8182703 and 8181646 — no modification required Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers Sold individually — most models require 4 shock absorbers; replace all 4 at the same time Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 8182703-4PK OEM Part Number WP8182703 Part Type Front-Load Washer Shock Absorber (Hydraulic Dampener) Condition Aftermarket Replacement Application Front-Load Washers Quantity Per Washer 4 (2 front, 2 rear) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper Compatible Series GHW, WFW, MHWE, MFW, KHWS Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves. Frequently Asked Questions What does the washer shock absorber do? The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time. How many shock absorbers does my front-load washer have? Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one. What is the difference between 8182703 and WP8182703? These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers. My washer still vibrates after replacing the shock absorbers — what else could it be? If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WH16X26913 Washer Genuine OEM Suspension Rod and Spring Rod and spring asm right- black Description: The Rod and Spring Asm Right-Black is an OEM replacement part for GE washing machines. It is responsible for providing the necessary tension and support for the washer drum. This assembly includes a durable rod and spring that work together to balance the drum and minimize excessive vibrations during the wash and spin cycles. Replaces Parts Numbers: WH16X26913, WH16X26714, AP6331892, PS12343383. California Residents only WARNING: California’s Proposition 65 

Read more less

XPARTCO WE03X37317 Dryer Drum Glide - Compatible with GE, Hotpoint, Kenmore Product Description Restore your dryer’s smooth operation with the WE03X37317 Dryer Drum Glide. This replacement glide supports the front of the dryer drum, ensuring smooth rotation. Designed for GE, Hotpoint, and Kenmore dryers, it fixes issues like squeaking, grinding, or improper drum rotation.  Note: Includes two glide. Replaces part numbers: WE03X37317, WE1M1067, WE01M0316, WE03X37317-50PK, WE1M1067-100PK, WE1M316, WE1M481, WE1M507, AP5668531, AP7217723, PS6447706, PS17137203. Compatibility: Compatible with models including but not limited to: GE: GTD42EASJWW, GTD65EBSJWS, GTD33EASKWW, GTX33EASKWW, GTD72EBPNDG Hotpoint: HTX24EASKWS, HTX21PASKWW Kenmore: 363.61542410 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select GE, Hotpoint, and Kenmore dryer models. 🔄 Specifications: Replacement plastic drum glide, ~2 11/16" x ⅝" polytetrafluoroethylene, clips onto drum support for reliable rotation. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, putty knife, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves squeaking, grinding, or improper drum rotation. Installation Notes: Safety First: Unplug the dryer or shut off the circuit breaker before installation to avoid electrical shock. Remove top and front panels, access drum support, remove old glide, install new glide, and reassemble. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less