Search results for "washer gasket"

W11168743 Genuine OEM Whirlpool Washer Hot Water Inlet Valve The W11168743 is a genuine Whirlpool OEM hot water inlet valve for Whirlpool top-load washers. This is a single-solenoid valve dedicated specifically to hot water, with a standard hose fitting inlet and one water outlet. When the wash cycle calls for hot water, the valve's solenoid opens to admit it from your home's hot water supply line; once the correct fill level is reached, it closes again. Rated 120V, 60Hz. Common causes of failure include wear and tear over time, clogging from mineral deposits or sediment in the water supply, and electrical faults that prevent the valve from opening or closing properly. A failing hot water valve typically shows up as the washer not filling properly or not filling at all, slow or irregular water flow even when the inlet screens are clear of obstruction, no hot water reaching the tub, or water dripping inside the tub when the washer isn't running. It directly replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, and 33390068. Quick Answer The W11168743 Genuine OEM Whirlpool Washer Hot Water Inlet Valve fixes Whirlpool top-load washers (and select Maytag, KitchenAid, Jenn-Air, Amana, Roper, and Kenmore washers) that won't fill, fill slowly, have no hot water reaching the tub, or leak water inside the drum when not running. 1-solenoid, 1-inlet, 1-outlet hot water valve. 120V, 60Hz. Replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, 33390068. This is the hot valve — the matching cold valve for the same platform is a separate part, W11168740. Common Problems This Part Fixes Washer not filling properly, or not filling at all Water flow slow or irregular even when inlet screens are clear No hot water reaching the tub during the wash cycle Water dripping or leaking inside the tub when the washer isn't running Washer not washing properly due to insufficient hot water Washer that won't start because it's stuck waiting for water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168743, 1873019, 33390068, 4585634, W10240948, W10921515, WPW10240948, AP6017592, AP6327638, EAP11750891, EAP12348074, PS11750891, AWP43142, OEM18982923, PD00040928, PS12348074. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, and Ikea washers built on the Whirlpool platform. Note — hot valve, not cold: This is the hot water valve. The matching cold water valve for the same Whirlpool top-load platform is a separate part, W11168740 (blue body, 2-solenoid). The two are not interchangeable, so replace the correct one for the symptom you're seeing — or both if you're unsure which is causing the issue. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration Dedicated hot water valve — standard hose fitting inlet, single water outlet Resolves "won't fill," "fills slowly," "no hot water," and "leaking inside the tub" symptoms caused by valve failure Rated 120V, 60Hz Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, and 33390068 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11168743 Part Type Washer Hot Water Inlet Valve Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Voltage 120V Frequency 60 Hz Solenoids 1 Inlets 1 (standard hose fitting) Outlets 1 Companion Part W11168740 (cold water valve, 2-solenoid, sold separately) Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the hot water supply valve before beginning. Wear work gloves. Access is typically from the rear of the washer: remove the screws securing the top or rear panel to reach the valve. Have a towel handy for residual water when you disconnect the supply hose. Photograph the wiring and hose connections before disconnecting anything. Disconnect the hot water supply hose, disconnect the electrical connector, and remove the mounting screws holding the valve in place, then pull it free. Install the new W11168743 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the hot water supply hose, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. While you're in there, it's also worth checking the hoses that run from the valve into the detergent dispenser drawer, since a loose or damaged hose at that connection can produce similar fill or leak symptoms. Restore the water supply and check for leaks before restoring power. Run a test cycle to confirm the washer fills normally with hot water. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I know if it's the hot valve or the cold valve that's failed? Pay attention to which water temperature is affected. If the washer isn't getting hot water but cold-water fills work fine, this hot valve (W11168743) is the likely cause. If the opposite is true, the cold valve (W11168740) is more likely the issue. If both hot and cold fills are affected, or you're not sure, it's worth checking both valves before ordering. I have water dripping inside the tub when the washer isn't running. Is this the valve? Yes, likely one of the two inlet valves. A worn internal seal can let water seep through even when the valve should be fully closed, causing exactly this symptom. Since there are two valves (hot and cold) on this platform, you may need to inspect both to determine which one is leaking, or replace both if you're unable to isolate it. The valve and hoses look fine but water flow is still irregular. What else should I check? If the inlet screens are clear of obstruction and water flow is still weak or inconsistent, it's worth checking the hoses that run from the valve into the detergent dispenser drawer, since a kink, clog, or loose connection there can produce similar symptoms to a failing valve. Household water pressure and any inline filter screens are also worth ruling out. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and hose connection configuration of the hot water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH23X29538 Washer Genuine OEM Water Valve Fits Specific GE Washer Models. Replaces Part Number WH23X29538, OEM20970350, AP6990115, PS16217225 Description: This Water Valve is a replacement part compatible with specific GE  washing machine models. As a key component located inside the washer cabinet, this valve precisely controls the flow of water into the machine during wash cycles. It allows for the filling of the tub with the proper amount of water at the correct temperature per the settings.

Read more less

W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly The W11670519 is a genuine Whirlpool OEM lid lock latch assembly for Maytag top-load washers on the Cabrio-style MVW platform. Unlike a simple mechanical lid switch, this is a true electronic lid lock: a 3-wire connector feeds the assembly, which both senses whether the lid is closed and physically locks it shut once a cycle with spin is underway. The control won't allow the washer to spin — and on many cycles won't even let it start — until this assembly confirms the lid is closed and locked, which is why a failing latch produces such a wide range of symptoms: a washer that won't start, a lid that won't lock or won't release, cycles that stall or interrupt partway through, or a washer that fills and agitates but refuses to spin. Built from high-strength, wear-resistant ABS and PP plastic with a precision locking mechanism, this assembly is designed to prevent the lid from popping open mid-spin, which protects against water leakage and the safety hazard of an open lid on a spinning basket. Common failure modes include a locking mechanism that has worn out and can no longer engage or release reliably, a broken internal switch that stops signaling lid status to the control board, and simple wear from years of daily cycling. It directly replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992. As a genuine OEM part, the W11670519 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly fixes Maytag top-load washers on the Cabrio-style MVW platform where the washer won't start, the lid won't lock or won't release, the washer fills and agitates but won't spin, the cycle stalls or interrupts, or the lid clicks repeatedly without locking. 3-wire electronic lid lock, ABS/PP construction. Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, EAP17215992. This is a locking latch assembly, not a simple lid switch — it's a different design from the direct-drive and GE-platform lid switches elsewhere in our catalog. Common Problems This Part Fixes Washer won't start even though the lid is closed Lid won't lock, or locks but won't release when the cycle ends Washer fills and agitates normally but won't spin Persistent clicking sound from the lid area without the lid actually locking Cycle stalling or interrupting partway through Lid feels loose or doesn't seat and lock the way it used to Error code related to the lid lock displayed on the control panel Water leakage risk from a lid that isn't sealing and locking properly during spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid lock latch assembly directly replaces the following OEM and cross-reference part numbers: W11670519, W11368616, AP7214714, AWP46151, PD00085482, 4981394, PS17215992, EAP17215992 W11368616 was an earlier number for this same assembly. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock latch assembly is compatible with select Maytag top-load washers on the Cabrio-style MVW platform, including model numbers such as: MVW4505MW0, MVW4505MW1, MVW4505MW2 MVW5035MW1, MVW5035MW2 MVW5430MW1, MVW5430MW2, MVW5430PBK0, MVW5430PBK1 MVW5435PBK0, MVW5435PBK1, MVW5435PW0, MVW5435PW1 Note: This is an electronic locking latch assembly for the Maytag Cabrio-style MVW platform, and it is a different design from the simpler lid switches used on other Whirlpool platforms — including our 8318084 (direct-drive top-load), 3355806 (Whirlpool thin-twin), WH12X955 (GE combo/spacemaker), and WH01X29528 (GE front-load door lock) listings. None of those are interchangeable with this assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which lid lock or switch your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism and switch design Electronic lid lock — both senses lid position and physically locks the lid during spin cycles Resolves "won't start," "lid won't lock or release," "fills but won't spin," and "cycle interruptions" symptoms caused by latch failure 3-wire connector for a direct plug-and-play electrical connection Constructed from high-strength ABS and PP plastic for wear and aging resistance Precision-designed locking mechanism helps prevent accidental lid opening during spin Direct drop-in replacement — no modification required Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11670519 Part Type Washer Lid Lock Latch Assembly Condition Genuine OEM Brand Whirlpool / Maytag Application Maytag Cabrio-Style Top-Load Washers (MVW Platform) Electrical Connection 3-wire connector Material High-strength ABS and PP plastic Function Senses lid closure and physically locks the lid during spin Supersedes W11368616 Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag Installation Notes ⚠️ Unplug Washer Before Starting — If The Lid Is Locked Shut, Release It Manually First Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. If the old latch has failed in the locked position and you can't open the lid, insert a small flathead screwdriver into the latch opening where the lock mechanism engages through the lid, and gently slide the mechanism back to release it — then prop the lid open so it can't re-close and re-lock while you work. Remove the two screws holding the top section (control panel, lid, and wash basket opening) and slide the top of the unit forward and up to remove it, then prop it securely (a sturdy support between the cabinet frame and the top panel works well) rather than relying on your hands to hold it up. With the top propped open, remove the plastic cowl that the lid latch sits inside, which also retains the lock mechanism. Unclip the wiring harness from the retaining clips running around the inside of the lid and let the assembly hang free. Photograph the wiring connections before disconnecting the 3-wire connector from the old assembly. At the back of the lid, two metal spring clips retain the mechanism — squeeze these with your fingers or a set of pliers to release the old assembly, then pop the new W11670519 into place the same way. Reconnect the 3-wire connector, reclip the wiring harness into its retaining clips, and reinstall the plastic cowl. Lower the top panel back into position, reinstall its retaining screws, and confirm the lid closes, latches, and locks correctly through a full test cycle including spin. Tools needed: small flathead screwdriver, Phillips screwdriver, pliers, a sturdy prop for the top panel, work gloves. Frequently Asked Questions My washer fills and agitates but won't spin. Is this the lid lock? Yes, this is one of the most common symptoms of a failing lid lock latch on this platform. The control requires confirmation that the lid is closed and locked before it will allow the higher-speed, higher-torque spin cycle to run, even if it's willing to run the gentler fill and agitate steps without full confirmation. If your washer gets partway through a cycle and simply refuses to spin, this assembly is a strong suspect. The lid keeps clicking but never actually locks. What does that mean? A repeated clicking sound without the lid actually locking usually points to a worn or failing internal locking mechanism inside this assembly — it's attempting to engage but can't complete the lock reliably. This is a textbook symptom that this part has worn out and needs replacement. My washer's lid is locked shut and won't open. How do I even get it open to do this repair? With the washer unplugged, you can usually manually release the lock: insert a small flathead screwdriver into the latch opening where the mechanism engages through the lid, and gently slide it back to disengage the lock. Once the lid is open, prop it so it can't fall shut and re-lock while you continue the repair. Is this the same part as the lid switches used on other Whirlpool washers? No. This is an electronic locking latch assembly specific to the Maytag Cabrio-style MVW platform, and it works differently from the simpler mechanical lid switches used on other Whirlpool-family platforms, including the direct-drive top-load switch, the Whirlpool thin-twin switch, and various GE-platform switches we also carry. These parts are not interchangeable with each other — always match the assembly to your specific washer platform. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-wire electrical connection, locking mechanism, and ABS/PP construction as the lid lock latch assembly originally installed in your Maytag Cabrio-style washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11175771 Genuine OEM Whirlpool Dishwasher Water Valve The W11175771 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers, located behind the lower kick plate panel in either the right or left corner. This valve controls the flow of water into the appliance during the wash cycle — an electrical solenoid plunger opens and closes the valve to admit exactly the right amount of water at the appropriate stages of the dishwasher's cycle. Measuring approximately 3.37" in height, this is a superseding part, replacing the earlier W10872255 and W11130744 valve numbers so older models can be updated with the current version. Over time, a screen inside the valve can become clogged with sediment — this screen isn't designed to be cleaned or serviced, so a clog means the whole valve needs to be replaced. A failing valve produces a clear set of symptoms: the dishwasher not filling with enough water or not filling at all, leaking into the dishwasher while not in use, or overfilling with too much water. It directly replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743. Quick Answer The W11175771 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers that aren't filling with water, are leaking, or are overfilling. Located behind the lower kick plate panel. Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, W11130743. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter, since it's in the same area and easy to inspect at the same time. Common Problems This Part Fixes Dishwasher not filling with enough water, or not filling at all Water leaking into the dishwasher while it's not in use Dishwasher overfilling with too much water High-pitched whining sound while the dishwasher is filling Poor washing results or an error code related to water fill Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11175771, 3015468, 328C151-T, 4451572, 4843711, AP5804368, AP6024301, AP6339872, EAP11738107, EAP12578165, EAP3406951, AWP43823, PD00052484, PS11738107, PS12578165 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers built on the Whirlpool platform, including model numbers such as WDF130PAHB1, WDF130PAHB2, WDF130PAHS1, WDF130PAHS2, WDF130PAHW2, WDF330PAHB3, WDF330PAHW4, WDF331PAHB1, WDF520PADB9, WDF520PADM, WDT730PAHZ, WDT720PADM, WDF330PAHS, ADB1400AGW, KDTE104ESS1, and Kenmore 66513222N410 through N414. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher via an electrical solenoid plunger Resolves "won't fill," "leaking," "overfilling," and "whining noise" symptoms caused by valve failure Superseding part — current replacement for the earlier W10872255 and W11130744 valves Approximately 3.37" in height Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743 Compatible with Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11175771 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Behind the lower kick plate panel, right or left corner Height 3.37" Supersedes W10872255, W11130744 Screen Serviceable No — replace valve if clogged Repair Difficulty Easy to Moderate — approx. 15 to 30 minutes Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, Inglis Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the bottom front kick plate to access the interior, where the valve is located behind the panel in either the right or left corner depending on your model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water line, the electrical connector, and remove the mounting screws securing the old valve, then pull it free. Install the new W11175771 in the same position, securely reconnect the water line and electrical connector, and secure the mounting screws. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Reinstall the kick plate, restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Can I just clean the valve's screen instead of replacing the whole thing? No — the screen inside this valve isn't designed to be cleaned or serviced. If it becomes clogged with sediment from your household water supply, the entire valve should be replaced rather than attempting to clean or repair the screen itself. My dishwasher makes a high-pitched whining sound while filling. Is that this valve? Yes, this is a documented symptom of a failing water inlet valve. One customer specifically traced an "obnoxious high-pitched whining sound when filling with water" to this exact valve and resolved it with a straightforward replacement in about 15 minutes. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

285805 Genuine OEM Whirlpool Washer Water Inlet Valve The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves. This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517. Quick Answer The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer won't stop filling — overfilling past the normal level Water leaking or dripping from the washer after the cycle has ended No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cycle stalling at the fill step and never advancing to wash Hot water inlet blocked by calcium or mineral deposits after years of hard-water use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including: Whirlpool top-load washers and laundry centers Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Complete kit — includes mounting bracket, screws, and installation instructions Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform Approximately 5.7" tall, metal and plastic construction Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 285805 Part Type Washer Water Inlet Valve Kit Condition Genuine OEM Brand Whirlpool Application Direct-Drive Top-Load Washers / Laundry Centers Kit Contents Water inlet valve, mounting bracket, screws, instructions Ports 2 (hot and cold) Hose Compatibility 1/2" ID Thread Specification Two 3/4"-11 x 1/2" NHT hose threads Height Approx. 5.7 in. Material Metal and plastic Color Blue or green (both correct — varies by production run) Quantity 1 valve kit Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions My valve is blue but the old one was green (or vice versa). Did I get the wrong part? No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance. The new valve's bracket doesn't match my old one. What do I do? This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent. Only hot water won't fill, but cold works fine. Is that this valve? Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled. My washer won't stop filling. Is that dangerous, and is it this valve? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688995 Washer Water Inlet Valve (Cold) The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688995 Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X10031 Washer Water Inlet Valve The XPARTCO WH13X10031 is an aftermarket replacement water inlet valve for GE washer/dryer combo units, and also fits select Hotpoint and Kenmore combo models. This valve controls the flow of water into the washer side of the combination unit, opening to admit hot and cold water as the cycle calls for it and closing once the correct fill level is reached. Made of durable metal construction for long-term reliability. Rated 115V. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer side not filling properly, water continuing to enter the machine even when it's turned off, or leaking near the valve connections. Quick Answer The XPARTCO WH13X10031 Washer Water Inlet Valve fixes GE washer/dryer combo units (and select Hotpoint and Kenmore combo models) that aren't filling properly, or where water continues entering the machine even when it's turned off. 115V, metal construction. This is a combo washer/dryer unit valve — a different application from a standalone top-load or front-load washer valve. Confirm your unit type before ordering. Common Problems This Part Fixes Washer side of the combo unit not filling with water properly Water continuing to enter the machine even when it's turned off Leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers WH13X10031, 1264513, AGE1189086, AP3995207, PS1482394. We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This water inlet valve is compatible with select GE washer/dryer combo units, and also fits select Hotpoint and Kenmore combo models built on the GE platform. Note — combo unit valve, not a standalone washer valve: This valve is specifically designed for washer/dryer combo units. GE also sells several similarly-numbered valves for standalone top-load and front-load washers, including WH13X10015, WH13X10030, WH13X10033, and WH13X10037 — these are separate parts for different platforms and are not interchangeable with this combo unit valve. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your appliance needs. Key Features Aftermarket replacement water inlet valve for GE washer/dryer combo units Resolves "won't fill properly" and "water continues entering when off" symptoms caused by valve failure Rated 115V Durable metal construction Direct drop-in replacement — matches the original mounting and hose connections Compatible with GE, Hotpoint, and Kenmore washer/dryer combo units Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WH13X10031 OEM Part Number WH13X10031 Part Type Washer/Dryer Combo Water Inlet Valve Condition Aftermarket Replacement Application Washer/Dryer Combo Units Voltage 115V Material Metal Quantity 1 valve Compatible Brands GE, Hotpoint, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to the valve on combo units typically requires removing a front or rear access panel — check your model's service diagram, since access varies more on combo units than on standalone washers. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water supply lines from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new WH13X10031 in the same position, reconnect all hose connections to their original positions, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold supply lines, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle to confirm the washer side fills correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Is this the right valve for my standalone washer, or only for a combo unit? This valve is designed specifically for GE washer/dryer combo units, where the washer and dryer are built into a single appliance. If you have a standalone washer, this is not the correct valve — GE uses several other similarly-numbered valves, such as WH13X10015, WH13X10030, WH13X10033, and WH13X10037, for standalone top-load and front-load washers. Confirm your unit type and model number before ordering. Water keeps entering my machine even when it's off. Is this the valve? Yes, this is a documented symptom of a failing water inlet valve. If the internal solenoid is stuck open or has worn out, water can continue to flow into the machine even after it's been turned off, since the valve can no longer fully seal. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the voltage rating, solenoid design, and connection type of the original WH13X10031 valve used in compatible GE, Hotpoint, and Kenmore washer/dryer combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM W11210463 Washer Water Inlet Valve The Genuine OEM Whirlpool W11210463 is the water inlet valve assembly for select Whirlpool, Maytag, Amana, Crosley, Admiral, Inglis and Roper washers. The valve controls the flow of hot and cold water into the washer. When it fails, the washer may not fill, may fill slowly or with too little water, or may leak. This is the original Whirlpool part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering, because several similar inlet valves exist. Quick Answer The Genuine OEM W11210463 Water Inlet Valve replaces the inlet valve on a compatible washer when it has failed. Replaces W10701461, W10869803, W10883458, W11038696 and W11101906. Classic symptoms: the washer won't fill or fills slowly, leaks, or gets no hot or cold water. Common Problems This Part Fixes Washer won't fill, or fills slowly No hot or cold water Water leaking from the valve Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve replaces or supersedes the following part numbers: W11210463, W11038696, 4591539, W10701461, W10869803, W10883458, W11101906, AP6329219, PS12349269 If your old valve shows a different number, contact our support team and we'll check whether it matches. Compatibility This water inlet valve is listed for Whirlpool, Maytag, Amana, Crosley, Admiral, Inglis and Roper washers, including these examples: Whirlpool WTW4816FW3, NTW4516FW2, NTW4665GW0, RTW4516FW2, MVW4005SW0, ITW4871FW3, CWW3812RW0, VWW3809RW0 Maytag ATW4516HW0, NTW4516FW3 Amana NTW4516FW4, NTW4605EW1, NTW4655EW1 Crosley CAW11544EW2, CAW8350EW2 Admiral ATW4516MW0 Inglis ITW4671EW1, ITW4971EW1 Note: The models above are a sample, not a full list. Whirlpool sells similar inlet valves under other part numbers. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Controls the flow of water into the washer Replaces five earlier Whirlpool valve part numbers Sold individually Product Specifications Part Number W11210463 OEM Part Number W11210463 Part Type Washer Water Inlet Valve Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Valve Application Select Whirlpool-Built Washers Installation Notes ⚠️ Disconnect Power And Water Before Installing Unplug the washer and shut off the water supply before you begin, and wear work gloves. Disconnect the water hoses and the wire connectors from the old valve, noting where each goes, and remove it. Fit the new valve, reconnect the hoses and connectors, restore power and water, and check for leaks while the washer fills. Frequently Asked Questions My washer won't fill or fills slowly. Is this the part I need? It can be. Check that both water supplies are on and the hose screens are clear first, since a blocked screen can cause the same symptom. If those are fine, the inlet valve may have failed. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Does this replace my old valve number? It replaces W10701461, W10869803, W10883458, W11038696 and W11101906. If your valve shows another number, contact our support team and we'll check it. Will this fit my washer? It is listed for many Whirlpool-built models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11244231 Genuine OEM Whirlpool Washer Drain Hose The W11244231 is a genuine Whirlpool OEM drain hose for Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers. This flexible tube carries used water from the washer tub to your house drain after every wash cycle, connecting the washer's outlet to your standpipe or utility sink drain connection. This hose is approximately 4 feet long and ships as a kit that includes a clamp. Over time, normal wear and tear, exposure to high water pressure or temperature, or physical damage from kinks and pinches can cause the hose to crack, bulge, or leak. A failing drain hose typically shows up as water leaking around the hose connections or along its length, slow or improper draining, or visible cracks and bulges in the hose material. It directly replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897. Quick Answer The W11244231 Genuine OEM Whirlpool Washer Drain Hose fixes Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers with a cracked, bulging, or leaking drain hose, slow draining, or a missing hose. Approximately 4 feet long, includes clamp. Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, PS12578897. This is a separate part from our W11281268 drain hose listing, which fits a different set of washer models — always confirm your exact model number before ordering. Common Problems This Part Fixes Water leaking around the hose connections or along its length Slow draining or improper drainage of the tub Visible cracks, bulges, or damage to the hose material Missing drain hose on a newly acquired or moved washer Reduced washer efficiency from a clogged, worn, or damaged hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain hose directly replaces the following OEM and cross-reference part numbers: W11244231, W10826733, W10221546, 4814009, W10769870, W10821090, W11199768, W11199820, W11203364, W11249137, AP6339776, AWP43752, OEM19019337, PD00045186, PS12578897 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain hose is compatible with select Whirlpool washers, and also fits select Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers built on the Whirlpool platform, spanning Whirlpool series 1CWTW4, 2DWTW, 3DWTW, 3LWTW, 3NWTW4800, 3SWTW4800, and 4GWTW, and Maytag series 3LMVWC, 4GMVW, 4KMVW, 4KNTW, 7MMVW, and MVWX6, including specific model numbers such as: MVWX655DW1, NTW4516FW3, VAW3584GW0 WTW4816FW2, WTW5000DW1, WTW5000DW2, WTW5000DW3, WTW9500EC0 WTW5100HC0, WTW5500BW0, WTW5600XW0, WTW5700AC0, WTW5800BC0, WTW6120HC0 WTW7000DW0, WTW8000DW0 ITW4871FW0, ITW4871FW1, ITW4871FW2 4KMVWC415FW0, 4KMVWC430JW0, 7MWTW1504DQ0 Kenmore 11026112310 Note — not the same as W11281268: This is a separate part from our W11281268 drain hose listing, which fits a different set of Whirlpool, Maytag, and Amana washer models with its own cross-reference set. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hose your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified length and fitting design Carries wastewater from the washer to your house drain during the drain cycle Resolves "leaking around connections," "slow draining," and "cracked or bulging hose" symptoms Approximately 4 feet long Ships as a kit including a clamp Direct drop-in replacement — matches the original fitting and length Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897 Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11244231 Part Type Washer Drain Hose Kit Condition Genuine OEM Brand Whirlpool Length Approx. 4 feet Includes Clamp Related Part W11281268 (6' hose, different model fitment, sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 drain hose kit Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Transfer Your Old Clamps To The New Hose Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off the water supply before beginning. Wear work gloves. Remove the back panel of the washer, then the lower front access panel to access the drain hose connection. Place a towel down before disconnecting any hoses to catch any remaining water. Disconnect the old hose from the washer's outlet spout and from your standpipe or drain connection. Transfer your existing hose clamps onto the new W11244231 hose during installation. Fit the new hose over the outlet spout and secure the clamp, then reconnect the other end to your house drain. Reinstall the lower front access panel and back panel. Restore the water supply and power, then run a test cycle to confirm the hose is secure with no leaks. Tools needed: multi-screwdriver, standard pliers, work gloves, towel. Frequently Asked Questions My washer is leaking. Is this the right part? It's worth checking, especially if the leak appears to come from around the hose connections or along its length rather than from the washer's tub or valve area. A cracked, bulging, or worn drain hose is a documented cause of leaking and can be resolved by replacing the hose to restore proper drainage. Is this the same as your W11281268 listing? No, these are two separate genuine Whirlpool drain hoses that fit different sets of washer models, with their own distinct cross-reference lists. Always confirm your exact model number against the compatibility list for each listing rather than assuming either hose is a universal fit. Do I need to buy new hose clamps separately? This hose kit includes a clamp, but you'll still need to transfer your existing clamps from the old hose for any connections that don't come with a new one included. Keep your old hardware on hand during the swap rather than discarding it with the old hose. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length and fitting configuration of the drain hose originally installed on your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11542153 Oven Genuine OEM Door Gasket The W11542153 is a genuine Whirlpool OEM oven door gasket for Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper ranges and ovens. This seal fits into the groove around the oven door opening, creating a protective barrier between the door and the cavity that traps heat inside the oven, ensuring proper cooking temperature and even results. Rated for pyroceramic (self-clean) oven temperatures, made of black rubber. Over time, this gasket can rip, crack, warp, or lose flexibility from repeated heat cycling. Symptoms of a failing gasket include heat escaping from the range, the door not sealing properly, temperature changes inside the oven, or the gasket edges visibly lifting or misaligned. It directly replaces WPW10129032, WPW10658354, 8522416, W10129032, W10658354, 3186152, 3195023, 8273133, W11491751, AP7018861, AWP45435, EAP16555283, PD00082401, PS16555283. Quick Answer The W11542153 Oven Genuine OEM Door Gasket fixes Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper ranges and ovens with heat escaping, a door that won't seal properly, or inconsistent oven temperatures. Black rubber, rated for pyroceramic oven heat. Replaces WPW10129032, WPW10658354, 8522416, W10129032, W10658354, 3186152, 3195023, 8273133, W11491751, AP7018861, AWP45435, EAP16555283, PD00082401, PS16555283. W10535778 is not a substitute for this gasket — if your parts diagram lists W10535778, that's a different, non-interchangeable seal. Common Problems This Part Fixes Heat escaping from the oven or range door Door not sealing properly against the oven cavity Inconsistent or fluctuating oven temperatures Gasket edges lifting or misaligned Visible cracks, rips, or warping in the gasket Uneven cooking or baking results Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven door gasket directly replaces the following OEM and cross-reference part numbers: W11542153, WPW10129032, WPW10658354, 8522416, W10129032, W10658354, 3186152, 3195023, 8273133, W11491751, AP7018861, AWP45435, EAP16555283, OEM21056592, PD00082401, PS16555283 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door gasket is compatible with select Whirlpool ranges and ovens, and also fits select Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper ranges and ovens built on the Whirlpool platform, including model numbers such as WFE510S0AS, WFG510S0AS, AGR5630BDS, AGR5630BDW, WFC310S0AW, WFC310S0EW, WFE320M0JS, WFE320M0ES, AER6303MFS, WFE505W0JZ, WFE505W0JS, WFE515S0ES, WFE515S0JS, WFE550S0HZ, WFG515S0ES, 4KAER5500AW0, 4KAER5500AW1, 4KAER7685EW0, 4KAER7685EW1, 4KMER7600AW0, 4KMER7600AW1, 4KMER7600AW3, 4KMER7685ES0, 4KMER7685ES1, 4KMER7685EW0, 4KMER7685EW1, 4KWFC120MAW0, 4KWFC120MAW1, 4KWFC120MAW3, 4KWFE7685ES0, 4KWFE7685ES1, 4KWFE7685EW0, 4KWFE7685EW1, 4RF302BXEQ1, and 4RF302BXGQ0. Note — W10535778 is not a substitute: A customer specifically asked whether W10535778 could substitute for this gasket and was told it cannot — W11542153 is the correct part and must be ordered specifically for compatible models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which gasket your oven needs. Key Features Genuine Whirlpool OEM part — factory-specified rubber composition and profile Creates a protective heat-trapping seal between the oven door and cavity opening Resolves "heat escaping," "door won't seal," and "inconsistent temperature" symptoms Rated for pyroceramic (self-clean) oven temperatures Black rubber construction Direct drop-in replacement matching the original groove profile Replaces WPW10129032, WPW10658354, 8522416, W10129032, W10658354, 3186152, 3195023, 8273133, W11491751, AP7018861, AWP45435, EAP16555283, PD00082401, PS16555283 Compatible with Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, and Roper ranges and ovens Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11542153 Part Type Oven/Range Door Gasket Condition Genuine OEM Brand Whirlpool Color Black Material Rubber Heat Rating Pyroceramic (self-clean) rated Weight Approx. 0.40 lbs Length: Approx. 70 inches, 20 Mounting Clip Repair Difficulty Easy Quantity 1 door gasket Compatible Brands Whirlpool, Jenn-Air, Kenmore, KitchenAid, Maytag, Amana, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Range Before Starting And Let The Oven Cool Fully Ensure the oven is unplugged and completely cool before beginning. Open the oven door and inspect the gasket for cracks, warping, or gaps along the door perimeter. Remove the old gasket by pulling it out of the groove around the door frame. Clean the groove thoroughly to remove any residue or debris left behind. Align the new W11542153 gasket and press it evenly into the groove, working around the full perimeter. Check that all corners are seated properly and the gasket sits evenly with no gaps. Confirm the door seals fully when closed to maintain proper oven temperature and consistent cooking. Tools needed: none typically required. Frequently Asked Questions I feel heat escaping around my oven door. Is this the part I need? Yes, this is the most direct symptom of a failing door gasket. Once the rubber cracks, rips, or loses flexibility, it can no longer maintain a tight seal around the door opening, letting heat escape and affecting cooking temperature and consistency. Can I use W10535778 instead of this part? No, W10535778 does not serve as a substitute for this gasket. If your appliance requires this seal, you'll need to order W11542153 specifically rather than assuming a similarly-listed part number will work. Will the new gasket feel exactly like my old one? It should fit and seal properly, though some customers have noted the new gasket feels thicker, sturdier, or slightly different in material and design compared to the original — while still fitting perfectly and, if anything, sealing better than before. This is a normal manufacturing update rather than a sign of an incorrect part. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original groove profile and heat-sealing function of the door gasket originally installed in your oven or range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WH23X35712 Washer Water Valve The Genuine OEM GE WH23X35712 is an electromagnetic (solenoid) water valve for GE, Hotpoint, and Kenmore washers. The valve connects your home's water supply to the washer. It opens when the control energizes it to let water into the washer and shuts off to prevent overfilling. When it fails, the washer may not fill, may fill intermittently, or may fill slowly or weakly. This is the original GE part. GE washers use several different water valves that look alike, so confirm the part number against your model before ordering. Quick Answer The Genuine OEM WH23X35712 Water Valve fixes a GE, Hotpoint, or Kenmore washer that won't fill, fills intermittently, or fills slowly. It is a sealed on/off solenoid valve. Classic symptom: the cycle starts but little or no water comes in, and the supply taps and hoses are clear. Common Problems This Part Fixes Washer won't fill with water Intermittent filling during the cycle Slow or weak fill Valve that leaks or doesn't shut off properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water valve directly replaces the following part number: WH23X35712, 4984177, AGE26168, AP7211666, EAP17139268, PD00089992, PS17139268 No other GE part numbers were confirmed for this valve. Other GE washer valves with similar numbers, such as WH23X29553, are different parts. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This valve is listed for GE, Hotpoint, and Kenmore washers. GE-family washers sold as General Electric, Hotpoint, RCA, and Kenmore Note: We could not confirm a model list for this valve, so compatibility is stated by brand only. GE makes several look-alike washer valves that differ in coil count and connections. Enter your model number at checkout or contact our support team to verify fit before ordering. Key Features Genuine OEM GE electromagnetic (solenoid) water valve Sealed on/off valve that controls water flow into the washer Resolves no-fill, intermittent-fill, and slow-fill problems Listed for GE, Hotpoint, and Kenmore washers Product Specifications Part Number WH23X35712 OEM Part Number WH23X35712 Part Type Washer Electromagnetic (Solenoid) Water Valve Condition Genuine OEM Application GE, Hotpoint & Kenmore Washers Installation Notes ⚠️ Unplug Power and Shut Off the Water Unplug the washer and turn off the water supply before beginning. Wear work gloves, and have a towel and shallow pan ready for water left in the hoses. Follow your model's service guide to reach the valve, note the position of each wire connector and hose, and disconnect them. Handle the new valve by its body and avoid stressing the electrical connectors or the inlet and outlet fittings. Inspect the hoses and fittings, replace any worn seals, then reconnect everything and check for leaks with the water on. Frequently Asked Questions My washer won't fill. Is this the part I need? A failed water valve is a common cause. First check that the water supply taps are fully open and that the inlet screens at the hose connections aren't clogged. If both are fine and the washer still fills slowly or not at all, the valve is a likely cause. What does this valve do? It is an on/off solenoid valve. It opens when energized to let water in and closes to stop the flow and prevent overfilling. Can I use a different GE washer valve? Not unless your model's parts diagram calls it out. GE makes several valves that look alike but differ in coil count and connections. Use the number your model calls out, or contact our support team to confirm. Will this fit my washer? It is listed for GE, Hotpoint, and Kenmore washers, but we could not confirm a model list. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less