XPARTCO W10195839 Dishwasher Dish Rack Rear Adjuster Guide
Fits Specific Whirlpool, Maytag Dishwasher Models
Replaces Part Numbers: WPW10195839, W10195839, 1872227, AP6016799, PS11750092.
Description: This Rear Adjuster Guide is a replacement part for specific Maytag, Kenmore, Whirlpool dishwasher models, designed to ensure the smooth operation of the adjustable upper rack. This component plays a pivotal role in allowing the rack to move up and down effortlessly, accommodating various sizes of dishes and cookware.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO EXP480 Microwave Door Switch (NC - NO) Normally Closed / Open
The XPARTCO EXP480 is a universal replacement door interlock switch for microwave ovens and microwave/oven combination units. This is a critical safety component: microwave door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing any possibility of microwave radiation escaping the cavity while the door isn't fully closed and latched. This switch combines both a normally closed (NC) and normally open (NO) contact set in a single body, matching the dual-contact design used across a wide range of microwave door latch mechanisms.
Rated 16A maximum current, 250VAC maximum voltage, with an IP40 protection rating. Over time, these switch contacts can wear, pit, or fuse together from repeated cycling and the electrical load they carry every time the door opens and closes. A failing interlock switch typically shows up as a microwave that won't start at all, a display that works but the unit won't heat, or in less common but more serious cases, a switch that has fused shut and continues carrying current even when it shouldn't. It directly replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, and PS10057151.
Quick Answer
The XPARTCO EXP480 Microwave Door Switch (NC - NO) fixes microwave ovens and microwave/oven combos that won't start, won't heat, or have a door latch mechanism that isn't reliably cutting power when the door opens. 16A, 250VAC, combined NC/NO contact design. Replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, PS10057151. Never operate a microwave with a bypassed, disconnected, or suspected-faulty door interlock switch — these switches exist to prevent radiation exposure and must always be replaced with a properly rated part, never removed or defeated.
Common Problems This Part Fixes
Microwave won't start at all, even though the display and buttons respond normally
Microwave display and timer work, but the unit won't heat
Microwave stops working intermittently, especially around the door latch
Clicking or buzzing sound from the door area without the microwave starting
Breaker tripping when the door is opened, indicating a switch contact that has fused shut
Door that doesn't feel like it's latching securely
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This microwave door switch directly replaces the following OEM and cross-reference part numbers:
28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, W10727360, W10269457, 3379124, AP5950105, PS10057151
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is a universal replacement compatible with convection microwave ovens, grill microwave ovens, microwave/oven combination units, and solo microwave ovens across many brands, wherever the original switch matches this NC/NO contact configuration and electrical rating.
Note: Microwave door interlock systems typically use two or three separate switches working together (primary interlock, monitor/secondary switch, and sometimes a third safety switch), and not all of them share this same NC/NO configuration. Confirm which specific switch position has failed on your microwave, and match the contact configuration and electrical rating exactly — never substitute a switch with a different configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your microwave needs.
Key Features
Universal replacement microwave door interlock switch — combined NC (normally closed) and NO (normally open) contact design
Resolves "won't start," "won't heat," and "intermittent operation near the door latch" symptoms caused by switch failure
Rated 16A, 250VAC maximum
IP40 protection rating
Safety approved: CCC, CE, UL, VDE
Suitable for convection, grill, combination, and solo microwave ovens
Direct drop-in replacement matching the original mounting and terminal configuration
Replaces a wide range of OEM part numbers across Whirlpool, GE, and related platforms — see full list above
Built to OEM-equivalent quality standards
Product Specifications
Part Number
EXP480
Part Type
Microwave Door Interlock Switch (NC/NO Combination)
Condition
New — Universal Replacement Part
Contact Configuration
Normally Closed (NC) + Normally Open (NO)
Max. Current
16A
Max. Voltage
250VAC
Operating Temperature
-25°C to +85°C
Protection Degree
IP40
Contact Form
SPDT
Terminal Size
6.3mm (approx. 1/4")
Operating Force
25g (0.245N) – 400g (3.92N)
Material
Plastic
Color
Gray
Safety Approvals
CCC, CE, UL, VDE
Application
Convection, Grill, Combination, and Solo Microwave Ovens
Quantity
1 door interlock switch
Installation Notes
⚠️ Danger — Never Bypass A Door Interlock Switch Unplug the microwave before beginning any work, and if it's a built-in or over-the-range unit, shut off power at the breaker as well. Microwave ovens also contain a high-voltage capacitor that can retain a dangerous electrical charge even after the unit is unplugged — avoid touching internal components near the capacitor and magnetron. Door interlock switches are a critical safety system: they exist specifically to cut power the instant the door opens, preventing microwave radiation from escaping the cavity. Never operate a microwave with an interlock switch disconnected, bypassed, or jumpered, even temporarily — doing so can expose you and others to microwave radiation. If you are not fully comfortable working inside a microwave's internal compartment, have a qualified appliance technician perform this repair instead.
⚠️ Photograph Wiring Before Disconnecting — Match The Failed Switch Exactly Wear work gloves. Remove the outer cabinet or access panel per your model's service instructions to reach the door switch assembly, typically located near the door latch mechanism. Photograph the wiring on the old switch before disconnecting anything, and confirm you're replacing the correct switch position if your microwave uses multiple interlock switches. Disconnect the wire terminals from the old switch, remove its mounting screws, and pull it free. Install the new EXP480 in the same position, reconnect each wire terminal to its original position, and secure the mounting screws. Reinstall the cabinet or access panel. Restore power and test that the microwave starts normally with the door closed, and — this is the critical safety check — confirm the unit stops heating immediately when the door is opened during a test run with a cup of water. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
My microwave stopped working. How do I know if it's actually a door switch and not something else?
A common pattern is a microwave where the display and buttons respond normally, but pressing start does nothing, or the unit hums without heating — this points toward the door interlock circuit rather than the control board. Since these switches also serve a critical safety function, if you suspect a fault in this area, it's best to have it properly diagnosed and replaced rather than working around the symptom.
Is it safe to just disconnect a faulty interlock switch so the microwave will run?
No — this is not safe under any circumstances. Door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing microwave radiation from escaping. Bypassing, disconnecting, or jumpering one of these switches removes that protection and can expose you and anyone nearby to microwave radiation, even if the microwave otherwise appears to run normally. Always replace a faulty switch with a correctly rated new one rather than working around it.
My microwave trips the breaker whenever I open the door. What does that mean?
This can indicate that one of the door switches — often the one that should open when the door opens — has fused or welded its contacts shut from repeated electrical stress, so it continues carrying current when it shouldn't. This is a genuine safety concern and the affected switch should be replaced promptly rather than continuing to use the microwave.
My microwave uses more than one door switch. How do I know which one to replace?
Most microwaves use two or three separate interlock switches working together, and they don't always share the same contact configuration. Check your appliance's parts diagram or the physical switch you're replacing to confirm it matches this NC/NO combination design before ordering, and always test or verify function with a multimeter if you're uncertain which specific switch has failed.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
ERP 74007733 Surface Burner Knob
1/4" stem length,
6 o'clock flat,
0.256
Replaces Part Numbers:WP7733P410-60, 7733P410-60, 74007733, AP6011505, PS11744702, WP7733P410-60VP
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W11688995 Washer Water Inlet Valve (Cold)
The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached.
When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools.
Quick Answer
The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately).
Common Problems This Part Fixes
Washer not filling with cold water — valve solenoid not opening when commanded
Washer filling slowly with cold water — valve partially clogged or weak solenoid
F8E1 error code displayed — cold water inlet valve fault
LO FL (low flow) error code — valve unable to deliver normal water flow
Fabric softener not being dispensed — cold water flush to dispenser failing
Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing
Water leaks at the valve body — internal seal failure
Wash cycles taking much longer than normal due to slow fill
Replaces Part Numbers
This cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select front-load washers from the following brands:
Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series
Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series
Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series
Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series
Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series
Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series
Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series
Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series
Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related
Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models
Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models
KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models
Kenmore / Sears front-load washers — select Whirlpool-built models
Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering.
Key Features
Aftermarket replacement built to OEM-equivalent quality standards
Controls the flow of cold water into the washer during fill cycles
Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped
Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve
1/2" NPT threaded inlet for standard washer supply hose connection
Dimensions: approximately 3" H x 4" W x 3" L
Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature
Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737
Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers
Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair
Quick DIY repair — installs in 10–15 minutes with basic hand tools
Product Specifications
Part Number
XPW11688995
Part Type
Washer Water Inlet Valve (Cold)
Condition
Aftermarket Replacement
Application
Front-Load Washers (Whirlpool platform)
Water Type
Cold (paired hot valve is W11688994)
Inlet Thread
1/2" NPT
Dimensions
Approximately 3" H x 4" W x 3" L
Color
Blue / White
Material
Plastic / Metal
Error Codes Resolved
F8E1, LO FL (when caused by cold valve fault)
Often Paired With
Hot Water Inlet Valve (W11688994, sold separately)
Compatible Brands
Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves.
Frequently Asked Questions
What do error codes F8E1 and LO FL mean on Whirlpool washers?
Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes.
My washer isn't dispensing fabric softener — could this be the cold valve?
Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue.
Should I replace the hot water valve at the same time?
Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit.
My washer is dripping water into the tub even when it's off — is this the valve?
Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XP20AGC Microwave Line Fuse
20A, Glass Fuse
6X32MM
Replaces Part Numbers: 5304509451, 5304464087, 5304488359, 4583647, AP6230606, PS12071294, WB27X11138, 1810711, 261201200040, AH3486694, EA3486694, AP4980426, PS3486694.
Description: This Fuse is a replacement part for select microwave models. It's a critical safety component designed to protect the microwave from electrical overload by breaking the circuit if the current is too high. This fuse is specifically tailored to fit and function properly with Frigidaire microwave models, ensuring safety and reliability.
1408 Gas Furnace Hot Surface Igniter
The 1408 is a replacement 120V silicon carbide hot surface igniter for gas furnaces. When the furnace calls for heat, the igniter glows white hot and lights the gas burners. Over time the element can crack or wear out, and a failed igniter is a common reason a gas furnace tries to start but never lights or never heats.
This igniter replaces the Robertshaw 41-408 and the Rheem 62-22868-93. It is a furnace igniter, not an oven igniter, so check the part number and the look of your old igniter before ordering.
Quick Answer
The 1408 Gas Furnace Igniter replaces a cracked, burned-out, or failed hot surface igniter on a gas furnace that tries to start but won't light. Replaces 41-408 and 62-22868-93. Classic symptom: the inducer runs, but the igniter never glows and the burners never light.
Common Problems This Part Fixes
Furnace won't light, with no heat
Igniter does not glow when the furnace calls for heat
Cracked, broken, or visibly damaged igniter element
Furnace cycles through ignition attempts and then locks out
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This igniter directly replaces the following part numbers:
1408, 41-408, 62-22868-93, 62-22868-02, 62-22868-82, 62-22441-01, 62-22868-92, B340039P01, 767A-372, 271N, IG408, 41-408, 67900, IG1408
The first three numbers are the main references for this igniter. The others appear on retailer cross-reference lists. Confirm against your furnace's parts list, or contact our support team, if your furnace calls out a different number.
Compatibility
This igniter is a replacement for the Robertshaw 41-408 and the Rheem 62-22868-93, and it is used on gas furnaces that call for either one. The Rheem number is used on Rheem, Ruud, WeatherKing, and Protech furnaces, including these series examples:
Rheem/Ruud UGDG, UGLG, UGLH, UGPH, UGTA, UGVG
Rheem/Ruud 80LJ, 80PJ, 90RJ, 90TJ
Note: The series above are a sample, not a full list. Retailers do not list the lead length or connector style for this igniter, so compare your old igniter's shape, lead, and connector to the new one, and contact our support team with your furnace model number to verify fit before ordering.
Key Features
120V silicon carbide hot surface igniter for gas furnaces
Replaces Robertshaw 41-408 and Rheem 62-22868-93
Resolves no-light and no-heat problems caused by a failed igniter
Furnace igniter, not for gas ovens
Product Specifications
Part Number
1408
OEM Part Number
62-22868-93, 41-408
Part Type
Gas Furnace Hot Surface Igniter
Condition
Aftermarket Replacement
Element Material
Silicon Carbide
Voltage
120V
Application
Gas Furnaces
Installation Notes
⚠️ Turn Off Power and Gas Before Installing Switch off power to the furnace at the breaker and the furnace switch, and shut off the gas supply, before beginning. Wear work gloves. Let the old igniter cool, disconnect its lead, remove it, and fit the new igniter in the same position. Handle the new igniter only by its ceramic base, and avoid touching the silicon element, since skin oils can cause early failure. If the furnace still does not light, check the control board and the gas valve.
Frequently Asked Questions
My furnace won't light. Is this the part I need?
A cracked or burned-out igniter is a common cause. If the igniter doesn't glow when the furnace calls for heat, or the element is visibly cracked, it is likely the problem. If the igniter glows but the burners don't light, check the gas valve and control.
Does this replace the Robertshaw 41-408 and the Rheem 62-22868-93?
Yes, it is listed as a replacement for both. Because retailers do not list lead length or connector style, compare your old igniter to this one, or contact our support team, before ordering.
Why shouldn't I touch the igniter element?
Skin oils on the silicon element can cause the igniter to fail early. Handle it by the ceramic base only.
Will this fit my furnace?
It is used on gas furnaces that call for a 41-408 or 62-22868-93 igniter, but the series list above is only a sample. Check your furnace's parts list, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO MWC21105 Microwave High Voltage Capacitor, 2100 VAC 1.05 µF
The XPARTCO MWC21105 is an aftermarket replacement high-voltage capacitor for microwave ovens. It stores and releases electrical energy in the high-voltage circuit that powers the magnetron, the part that actually generates the heat. When the capacitor weakens or fails, the microwave can stop heating while the display, turntable, and light still work normally. It can also hum, trip the breaker, or blow the fuse.
Rated 2100 VAC and 1.05 µF, this oval, bracket-mounted capacitor has 1/4" male terminals and fits a wide range of microwaves from GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, Kenmore, and other brands. Because the same capacitor was used under many manufacturers' part numbers, it carries a long cross-reference list; see the Replaces list below. Each order includes 1 capacitor.
Quick Answer
The XPARTCO MWC21105 Microwave Capacitor fixes a microwave that runs but doesn't heat, hums, or trips the breaker or blows the fuse because of a failed high-voltage capacitor. 2100 VAC, 1.05 µF, oval, bracket-mounted, 1/4" male terminals. Classic symptom: the light, display, and turntable all work, but food comes out cold. This part holds a dangerous electrical charge, so it should be installed by a qualified service technician.
Common Problems This Part Fixes
Microwave runs but doesn't heat the food
Humming or buzzing noise from the microwave when it's running
Microwave trips the circuit breaker or blows the internal fuse
Weak or inconsistent heating
Visible bulging, leaking, or burn marks on the old capacitor
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This capacitor directly replaces the following part numbers:
WB27X11033, PD00030313, WB27X10308, WB27X10520, WB27X10701, WB27X10747, WB27X10805, 1474118, EAP2353613, AP4412060, PS2353613, W10850446, PD00032266, 4383732 EAP11731152, AP5999188, PS11731152, WB27X29988, PD00064298, 4586376, EAP12296267, AP6286260, PS12296267, 0CZZW1H004C, PD00032660, 1271742, EAP3517242, AP5199046, PS3517242, W10705215, W11335495, AP5956548, PS10063950, W11213318, PD00061266, EAP12349322, 4844491, AP6329441, PS12349322, WP8184813, PD00028888, EAP731741, 4437142, AP6011903, PS731741, WP4375020, PD00039292, EAP11742447, 4434444 AP6009291, PS11742447, 56002017, 56001435, AP4396772, 0CZZW1H004S, PD00008613, EAP3538829, 1271749 AP5199046, PS3538829, 0CZZW1H004K, 0CZZW1H001L, 1271745, EAP3517244, AP5199046, PS3517244
This capacitor was sold under the part numbers of many manufacturers, including GE (WB27X series), Whirlpool (W-series and WP-series), and LG and Samsung (0CZZW1H series), plus third-party catalog numbers (AP, PS, EAP, PD).
Note: The 1.0 µF capacitor (13QBP21100) is a different value and is not interchangeable with this 1.05 µF part. Always match the capacitance and voltage marked on your original capacitor.
Compatibility
This capacitor is used on microwave ovens from many brands, including:
GE, Kenmore, Whirlpool, Frigidaire, and Electrolux
Samsung, LG, and Goldstar
Panasonic and Sharp
Bosch, Magic Chef, Crosley, Admiral, Gibson, and Nrg
Note: Compatibility depends on matching the capacitance (1.05 µF), voltage rating (2100 VAC), and the physical size and terminal layout of your original capacitor, not just the brand. Check the values printed on your old capacitor, or contact our support team with your model number and we'll verify fit before you order.
Key Features
Aftermarket replacement microwave high-voltage capacitor
2100 VAC, 1.05 µF rating
Oval body with 1/4" male terminals and bracket mounting
Restores heating on microwaves with a failed capacitor
Cross-references to GE, Whirlpool, Samsung, LG, and other OEM numbering
1 capacitor per order
Product Specifications
Part Number
XPMWC21105
OEM Part Number
WB27X29988, W10850446, 0CZZW1H004C
Part Type
Microwave High Voltage Capacitor
Condition
Aftermarket Replacement
Voltage Rating
2100 VAC
Capacitance
1.05 µF (1.05 mfd)
Shape
Oval
Terminals
1/4" Male
Mounting
Bracket-Mounted
Quantity
1 Capacitor
Installation Notes
⚠️ Danger: Lethal Charge — Qualified Technician Installation Only A microwave high-voltage capacitor can hold a lethal electrical charge even after the microwave is unplugged. Installation should be done by a qualified service technician who knows how to safely discharge and test the high-voltage circuit. Do not touch the capacitor or its terminals, and do not open the microwave cabinet, unless you are trained to do so. Unplugging the microwave does not make this circuit safe. A technician will normally unplug the unit, safely discharge the capacitor, and note the wiring before removal. Match the replacement's capacitance, voltage rating, and terminal layout to the original, mount it securely in the same bracket position, reconnect the wiring as it was, and confirm all covers are back in place before powering the microwave.
Frequently Asked Questions
My microwave runs but doesn't heat — is the capacitor the problem?
A failed high-voltage capacitor is one common cause of a microwave that runs but doesn't heat. Other high-voltage parts, such as the diode and the magnetron, can cause the same symptom, so a technician will usually test them together before replacing parts.
Is it safe to replace this myself?
We recommend a qualified service technician install this part. A microwave capacitor can retain a lethal electrical charge even when the microwave is unplugged, and the high-voltage circuit is dangerous to work around without the right training and tools.
Can I use a capacitor with a different capacitance or voltage?
No. Use the same rating as your original. This listing is a 1.05 µF, 2100 VAC capacitor. A 1.0 µF capacitor (13QBP21100) is a different part and is not a substitute.
What's included in the order?
1 high-voltage capacitor. It does not include a diode, fuse, or other components.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
S48D21 8" Range Surface Element
Product Title
Aftermarket S48D21 8" Range Surface Element - Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, Amana Electric Ranges
Product Description
Revive your electric range’s cooking performance with the Aftermarket S48D21 8" Range Surface Element from Parts-O-Matic. This high-quality aftermarket burner element replaces the original S48D21, delivering 2100 watts at 240V with a 4-turn coil design for efficient and even heating. Ideal for select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other brand electric ranges, it addresses issues like uneven heating, slow warm-up, or non-functional burners. Enjoy free shipping on all orders at Parts-O-Matic!
Key Features:
✅ Broad Compatibility: Fits select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other electric range models.
🔥 Efficient Heating: 8" diameter, 4-turn coil delivers 2100 watts at 240V for consistent, even cooking.
💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Plug-in design with Y-style bracket; requires no tools and takes 5–10 minutes to install.
🛡️ Fixes Common Issues: Resolves uneven heating, slow warm-up, or burners that fail to heat.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: RF110AXSQ0, RF262LXSB, RF365PXKW0
Maytag: MER4110AAH, MER4120AAQ
Kenmore: 629.4297, 629.60003600 (pre-2004 models)
Jenn-Air: JES9750AAB
Amana: AER5511AAQ
Replaces part numbers: TJ90SP21MA, 14215226, 1938283, 309917, 403782, 404110, 406000, 814154, ERS48D21, SE302, SP21MA, SU214, SU302, TS4D8221, TS4D8221PB, TS4D8221SR, TS4D8221WI, YSP21MA, AP4503257.
Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance.
Installation Notes:
Tools Needed: None for standard installation; a flathead screwdriver may help for stubborn connections.
Safety First: Unplug the range before installation to avoid electrical shock.
Steps: Remove the old burner element by gently pulling it from the receptacle, align the Y-style bracket of the new S48D21 element, and plug it into the socket. Ensure the element sits flat in the drip pan. If the burner is not level, adjust the connection bolts to ensure they are parallel and push down gently. Installation takes 5–10 minutes. Note: A slight burning smell during first use is normal due to a protective coating; this will dissipate after 15–20 minutes.
Download our installation guide or watch our YouTube tutorial for step-by-step instructions.
Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Restore your range’s cooking performance today!
Add to cart now for an affordable fix with free shipping on your entire order!
EXPTC105 Test Lead Set
Set of 10 Wires
100% Brand new and high quality
Color coded leads allow you to test circuits without crossing wires or causing shorts
Can be used as low voltage jumper leads
Test Leads with Alligator Clips Set Insulated Test Cable Double-ended Clips
IMPORTANT! You should call ahead to confirm availability of an item before going to the store. store's actual inventory can change from minute to minute. Calling the store will allow you to confirm that the item is still available. Some items may not be immediately available for pickup at your local store. Prices and availability may differ from web prices at local pickup location.
