Search results for "refrigerator switch"

4681EA2001T Genuine OEM LG Washer Drain Pump Motor The 4681EA2001T is a genuine LG OEM drain pump motor for LG and Kenmore front-load washers, and also fits washer/dryer combo units. This motor is responsible for removing water from the washer at the end of the wash and spin cycles, expelling it through the drain hose so the machine can move on to the next stage of the cycle. This part is the motor only — you'll reuse your existing pump housing. It includes the pump impeller, which is not sold separately. Rated 120V-127V, 60Hz, 85W, 1.4A, with a flow rate of 45L per minute. Measures approximately 6.57" x 4.29" x 3.5". As of April 2025, the design of this drain pump motor changed to a gray housing, replacing the earlier black housing — this is expected and doesn't affect fit or function. Common failure causes include a worn or seized motor and general electrical wear. Symptoms of a failing drain pump motor include the washer not draining, unusual noise during the drain cycle, an OE error code, or leaking near the pump if the motor fails while still under load. It directly replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L. Quick Answer The 4681EA2001T Genuine OEM LG Washer Drain Pump Motor fixes LG and Kenmore front-load washers (and washer/dryer combos) that aren't draining, are making unusual noise during the drain cycle, or are showing an OE error code. 120V-127V, 60Hz, 85W, 1.4A, 45L/min. Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, 5214FR4006L. This is the motor only — reuse your existing pump housing when installing. As of April 2025, the new housing color is gray instead of the older black; this is a normal design change and not a compatibility issue. Common Problems This Part Fixes Washer not draining — standing water left in the tub after a cycle Unusual noise during the drain cycle OE error code displayed on the control panel Washer taking longer than normal to drain Leaking near the pump area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select LG front-load washers, and also fits select Kenmore Elite washers built on the LG platform, and washer/dryer combo units, including model numbers such as WM2101HW, WM3270CW, WM3431HS, WM3770HVA, WM3001HWA, WM8000HVA, WM8000HWA, WM2550HRCA, WM2550HWCA, GCW1069CS, WM3550HWCA, WM3070HRA, WM4070HVA, WM3070HWA, WM2350HRC, WM3360HVCA, WM2350HWC, GCW1069QS, WM2650HRA, WM3360HRCA, WM3360HWCA, WM3150HVC, WM2650HWA, WM2655HVA, WM3885HCCA, WM3150HWC, WM3885HWCA, WM2250CW, WM2450HRA, WM3987HW, WM3470HVA, WM3470HWA, LSWF388HVS, WM3550HVCA, WM2455HG, WM2277HB, WM2487HRMA, and Kenmore 79641072310. Note: Always verify your full model number before ordering, since LG uses several different drain pump designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor design and impeller Pumps wastewater out of the tub through the drain hose Resolves "not draining," "unusual noise during drain," and "OE error code" symptoms caused by motor failure Includes pump impeller (not sold separately) Reuses your existing pump housing — motor only Rated 120V-127V, 60Hz, 85W, 1.4A, 45L/min flow rate Direct drop-in replacement matching the original mounting and connections Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L Compatible with LG and Kenmore front-load washers and washer/dryer combo units Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 4681EA2001T Part Type Washer Drain Pump Motor Condition Genuine OEM Brand LG Application Front-Load Washers, Washer/Dryer Combos Voltage 120V-127V Frequency 60 Hz Wattage 85 W Amperage 1.4 A Flow Rate 45 L/min Dimensions Approx. 6.57" x 4.29" x 3.5" Housing Not included — reuse existing pump housing Housing Color (as of April 2025) Gray (previously black) Repair Difficulty Medium — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Have Towels Ready For Draining Water Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Lay towels down in front of the washer before starting, and have a pail ready. Remove the detergent drawer and check the drain filter (bottom lower left panel door) to confirm it's clean and the drain line isn't blocked before assuming the motor is at fault. Many customers find it easier to access the pump from underneath by carefully laying the washer on its back — be prepared for a significant amount of additional water to drain out onto the floor once you do this, so keep towels close by. With access to the pump, disconnect the electrical connector from the old motor and separate the motor from the pump housing, which you'll reuse with the new motor. Attach the new 4681EA2001T motor to your existing pump housing, transferring the impeller setup as needed. Reconnect the electrical connector fully. Stand the washer back upright, reinstall the detergent drawer, and reconnect the water supply and power. Test the new pump to confirm it drains properly before considering the repair complete. Tools needed: Phillips screwdriver, locking pliers, needle nose pliers, small flathead screwdriver, towels, work gloves. Frequently Asked Questions My washer shows an OE error code and isn't draining. Is this the part I need? Likely yes. An OE error code on LG washers is commonly tied to a drain issue, and a bad drain pump motor is one of the most frequent causes. Before replacing the motor, it's worth checking that the drain filter and coin trap (if your model has one) are clean and that the drain line itself isn't blocked, since those are simpler and cheaper things to rule out first. Does this come with the pump housing? No, this is the motor only, and it includes the pump impeller, which isn't sold separately. You'll reuse your existing pump housing during installation rather than replacing it as part of this repair. The new motor's housing looks a different color than I expected. Did I get the wrong part? No, this is expected. As of April 2025, LG changed the design of this drain pump motor to use a gray housing in place of the earlier black housing. This is a normal manufacturing update and doesn't affect fit or function. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, impeller, and electrical rating of the drain pump motor originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304519906 Dishwasher Pump and Motor Assembly Product Overview The XPARTCO 5304519906 Dishwasher Pump and Motor Assembly is designed to circulate water through the spray arms and ensure proper cleaning performance. This Motor & Pump Assembly is a replacement part for specific Frigidaire dishwasher models. This assembly is crucial for circulating water throughout the dishwasher during the wash and rinse cycles, ensuring that dishes are cleaned effectively. You should replace this motor and pump assembly if it becomes faulty. Common causes of a bad motor and pump assembly include electrical issues, wear and tear from regular use, or blockages caused by debris or food particles. Quick Answer If your dishwasher is not cleaning dishes, has weak spray pressure, makes unusual noises, or fails to circulate water, the 5304519906 pump and motor assembly may be faulty. Replacing it restores proper wash performance and water circulation. Replaces Part Numbers Replaces OEM part number: 5304519906, 154843901, EAP12712308, AFR18422, PD00053471, AP6840161, P154792801. Compatibility This pump and motor assembly is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible dishwashers. Frigidaire Dishwashers Electrolux Dishwashers Kenmore Dishwashers Always verify your appliance model number before ordering. Common Problems This Part Fixes Dishes not getting clean Weak or no water spray Dishwasher making loud or grinding noise Water not circulating during wash cycle Key Features Integrated pump and motor assembly Restores strong water circulation High-quality aftermarket replacement Reliable and durable construction Product Specifications Part Number: XP5304519906 Part Type: Dishwasher Pump and Motor Assembly Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dishwasher Water Circulation Troubleshooting Guide Dishes remain dirty → Weak or failed pump motor No spray action → Pump not circulating water Loud noise during wash → Motor or impeller issue When Should You Replace This Assembly? Replace this assembly if your dishwasher is not cleaning properly, lacks water pressure, or makes abnormal noises during operation. Installation Notes ⚠️ Disconnect power and water supply before installation. Access the pump and motor assembly from the bottom of the unit and install securely according to your dishwasher model. Related Parts Dishwasher Spray Arm Water Inlet Valve Drain Pump Frequently Asked Questions Will this assembly fit my dishwasher?This part fits many Frigidaire and compatible dishwashers. Always verify your model number. What does a pump and motor assembly do?It circulates water through the dishwasher to clean dishes effectively. What are signs of a bad pump motor?Poor cleaning, weak spray, or loud noises during operation. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

691366 Dryer Idler Pulley - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid Product Description Keep your dryer running smoothly with the 691366 Dryer Idler Pulley. This replacement idler pulley is designed as a replacement for select Whirlpool, Kenmore, Maytag, KitchenAid, and other compatible dryers, offering a cost-effective alternative to the original. It maintains proper tension on the drive belt to ensure the dryer drum spins correctly, preventing issues like belt slippage or drum failure. This part addresses symptoms such as the dryer not tumbling, making unusual noises (e.g., squeaking or squealing), failing to start, or taking too long to dry, often caused by a worn or broken idler pulley. Note: Includes (1) idler arm and pulley assembly. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP691366, 691366, 239477, 26000691366, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, WP691366VP, PD00002256, EAP11743765, AP6010582, PS11743765. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WED4815EW1, WED4850BW0, WED6600VU0, 1CWGD5790VQ0, 7EWED1510YM0 Kenmore: 110.77322600, 110.77432600, 110.72832101, 110.60022010 Maytag: MED5630TQ0, 4KMED5700TQ0, 7MMEDC300BW0 KitchenAid, Amana, Inglis, Roper, Crosley, Estate, Admiral, Magic Chef: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Crosley, Estate, Admiral, and Magic Chef dryers. 🔧 Specifications: High-quality plastic pulley with metal idler arm. 💪 Reliable Performance: Ensures proper belt tension for smooth drum rotation and efficient drying. 🛠️ Easy Installation: Requires screwdriver, nut driver, pliers; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves issues like no tumbling, noisy operation, failure to start, or prolonged drying times. Product Specification Part Number: 691366 Component Type: Dryer idler pulley Material: Plastic pulley, metal idler arm Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

WH23X29553 Genuine OEM GE Washer Water Valve The WH23X29553 is a genuine GE OEM water inlet valve for GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. This valve controls the flow of water into the washer from the household supply line — when the control calls for a fill, the valve's solenoid opens to admit water, and closes again once the correct level is reached. Built with an ABS plastic body and stainless steel components for durability against corrosion. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve typically shows up as the washer not filling properly, filling too slowly, or leaking water. It directly replaces WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643. Quick Answer The WH23X29553 Genuine OEM GE Washer Water Valve fixes GE front-load washers (and select Hotpoint, RCA, Haier, Monogram, and Café models) that aren't filling properly, are filling too slowly, or are leaking water near the valve connections. Replaces WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643. Not the same part as the similarly-numbered WH23X29538 valve — confirm you have the correct number before ordering. Common Problems This Part Fixes Washer not filling with water, or filling only partially Washer fills much more slowly than it used to Water leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform., including model numbers such as: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN2SN, GFW650SPN3SN, GFW650SPN4SN GFW650SSN0WW, GFW650SSN1WW, GFW650SSN2WW, GFW650SSN3WW, GFW650SSN4WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW GFW655SSV0WW PFW870SPV0RS PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note — not the same as WH23X29538: A similarly-numbered valve, WH23X29538, is a separate part (replaces 4977241, AP6990115, PS16217225, EAP16217225, 33090201, 0024000126GB) used on related but distinct models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and flow rate ABS plastic body with stainless steel components for corrosion resistance Resolves "won't fill," "fills slowly," and "leaking near the valve" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH23X29553 Part Type Washer Water Inlet Valve Condition Genuine OEM Brand GE Application Front-Load Washers Body Material ABS plastic Component Material Stainless steel Quantity 1 valve Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Release The Control Panel Carefully Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel on many models. When removing the front control panel, avoid pulling it straight out too far — slotted tabs on the right side of the panel can break if forced. Instead, pull the panel gently forward, then slide it to the right to release it cleanly. With the panel released, locate the valve and disconnect the hot and cold water supply hoses, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the outlet hoses from the old valve, remove its mounting screws, and pull it free. Install the new WH23X29553 in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the control panel and any surrounding trim, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I remove the front control panel without breaking it? Avoid pulling the panel straight out with heavy force — the slotted tabs on the right side of the panel can snap if you pull too far. Instead, pull the panel gently forward first, then slide it to the right to release it from its mounting. This gentler approach avoids the most common way this panel gets damaged during a valve repair. I've heard this valve sometimes needs replacing again after just a couple of years. Is that normal? Some owners have reported needing to replace this valve again within a relatively short time, even after a successful repair. While most installations hold up well long-term, if you experience a repeat failure, it's worth double-checking your household water pressure and mineral content, since hard water and high pressure can accelerate wear on any water valve regardless of brand. Is this the same as WH23X29538? The numbers look almost identical. No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close match, since ordering the wrong one means it won't fit correctly. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 137311900 Washer Drain Pump Assembly – Compatible with Frigidaire & Electrolux Washers Product Description Restore proper water drainage and dependable washer operation with the XPARTCO 137311900 Washer Drain Pump Assembly. This high-quality aftermarket replacement pump is designed to efficiently remove water during drain and spin cycles. A worn or failing drain pump can cause standing water, slow draining, error codes, or loud humming noises. Replacing it with this reliable XPARTCO pump helps return your washer to smooth, consistent performance at a budget-friendly price. XPARTCO aftermarket parts are engineered to match original fit and function while offering a cost-effective alternative to OE or Genuine OEM components. Replaces Part Numbers 137311900, 2688889, PD00006068, EAP3655041, AP5630474, PS3655041. Compatibility This replacement washer drain pump assembly fits select Frigidaire, Electrolux, Crosley, Gibson, and Kenmore (Frigidaire-manufactured) washers. Example compatible models include (but are not limited to): Frigidaire FAFW3577KW0, FFTW4120SW Electrolux EIFLW55HIW0 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pumping performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet, Smooth Operation – Helps eliminate humming or grinding noises 💪 Durable Motor & Housing – Built for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OE and OEM pumps 📐 Product Specification Part Number: 137311900 Component Type: Washer Drain Pump Assembly Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OE / not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new XPARTCO 137311900 drain pump assembly. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Fix drainage issues and get your washer running smoothly again — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

W10467289 Washer Genuine OEM Temperature Sensor Replaces Part Numbers: WPW10467289, W10467289, 2629420, 8181705, 8182291, 8540225, 8540226, W10176658, W10176659, OEM18065663, AP6021886,, PS11755214. Description: This Water Temperature Sensor is a Genuine OEM part for specific Kenmore, Whirlpool washing machine models. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WH01X29528 Genuine OEM GE Washer Door Lock The WH01X29528 is a genuine GE OEM door lock assembly for GE front-load washers and select GE Ultrafast 2-in-1 combo washer/dryers. This is a safety mechanism, not just a switch: when the door closes, the lock engages automatically and secures the door shut for the full length of the cycle, only releasing once the control confirms it's safe to open. This prevents the door from being opened mid-cycle, which would otherwise let water and detergent spill out and create both a mess and a safety hazard. Rated 120VAC, 60Hz, 16A. Over time, the door lock can fail from physical damage or ordinary wear, and when it does, the symptoms can be wide-ranging: a washer that won't start because the control never confirms the door is locked, a cycle that stops partway through, a door that won't unlock at the end of a cycle, or in some cases excessive noise and shaking during operation since the lock also plays a role in keeping the door assembly seated correctly. It directly replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, and 0024000128GE. As a genuine OEM part, the WH01X29528 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH01X29528 Genuine OEM GE Washer Door Lock fixes GE front-load washers and GE Ultrafast combo washer/dryers where the door won't lock, the washer won't start, the door pops open or unlocks unexpectedly during the cycle, or the cycle stops partway through. 120VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, 0024000128GE. Before replacing, try a power reset — unplug the washer for 30 seconds and plug it back in — or hold Start/Pause for 15 seconds to command the control to release the lock; either can resolve a door stuck locked without needing a new part. Common Problems This Part Fixes Washer won't start because the door lock never confirms as locked Door lock fails to engage, or the door pops open after locking Door unlocks unexpectedly during the wash cycle Cycle stops or interrupts partway through Door won't unlock at the end of a completed cycle Excessive noise or shaking during operation related to a loose door seal Error code related to the door lock displayed on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, V13305, AGE26402, PD00060769, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock is compatible with select GE front-load washers and GE Ultrafast 2-in-1 combo washer/dryers, including model numbers such as: GFW510SCN0WW, GFW510SCN1WW, GFW510SCN2WW, GFW510SCN3WW, GFW510SCN4WW, GFW510SCN5WW GFW550SPN0DG, GFW550SPN2DG, GFW550SSN1WW GFW650SPN1SN, GFW650SPN2SN, GFW650SSN2WW, GFW650SSN3WW GFW655SSV0WW, GFW655SPV0WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS, GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW, GFW850SSN4WW, GFW850SSN5WW PFQ97HSPV0DS (GE Ultrafast 2-in-1 combo washer/dryer) PFW870SPV0RS, PFW870SSV0WW PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note: Always verify your full model number before ordering, since GE uses several different door lock assemblies across its front-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified locking mechanism and switch design Safety lock that secures the door shut for the full length of the wash cycle Resolves "won't lock," "won't start," "door pops open," and "cycle interruptions" symptoms caused by lock failure Rated 120VAC, 60Hz, 16A Direct drop-in replacement — matches the original mounting and harness connector Replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, and 0024000128GE Compatible with GE front-load washers and GE Ultrafast 2-in-1 combo washer/dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH01X29528 Part Type Washer Door Lock Assembly Condition Genuine OEM Brand GE Application Front-Load Washers, GE Ultrafast Combo Washer/Dryers Voltage 120VAC Frequency 60 Hz Current Rating 16A Function Locks the door shut during the wash cycle; releases when the control confirms it's safe Quantity 1 door lock assembly Compatible Brand GE Installation Notes ⚠️ Unplug Washer Before Starting — Try A Power Reset First If The Door Is Stuck Locked Before replacing the part, try the simplest fixes first. Unplug the washer, wait 30 seconds, and plug it back in to let the control fully reboot — a simple power reset can release an operational lock and clear the problem without any disassembly. If that doesn't work, try holding the Start/Pause or Power button for 15 seconds to command the control to unlock the door; this doesn't always succeed but is quick to try before opening up the washer. If the door is still locked and you need physical access, never work on the appliance while it's connected to power. Once you've confirmed replacement is necessary, disconnect power at the outlet or shut off the circuit breaker. Wear work gloves. Access is typically from the front, working around the door boot/gasket to reach the lock assembly mounted to the front panel. Photograph the wiring harness connector and mounting position before disconnecting anything. Disconnect the harness connector from the old lock, remove its mounting screws, and pull it free. Install the new WH01X29528 in the same position, secure the mounting screws, and reconnect the harness connector fully. Reseat the door boot/gasket if it was disturbed, restore power, and run a test cycle to confirm the door locks, stays locked through the cycle, and releases normally at the end. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My washer's door is stuck locked. Do I need to replace this part right away? Not necessarily — try the simple resets first. Unplug the washer for 30 seconds and plug it back in to let the control fully reboot, which can release an operational lock on its own. If that doesn't work, try holding the Start/Pause or Power button for 15 seconds, which commands the control to release the lock electronically. These steps resolve many stuck-door situations without needing to replace the lock assembly at all. My washer won't start. Is that this part? It's a strong possibility. The control won't begin a cycle until it receives confirmation that the door is locked, so if this lock has failed and isn't sending that signal, the washer will simply refuse to start even though everything else appears normal. Try the power reset steps above first, then check for a door lock-related error code on the display before assuming the part has failed. I already replaced this lock once and it failed again. What should I check? If a newly replaced lock fails again relatively quickly, it's worth having the washer's control board checked, since a board that's sending incorrect signals to the lock can cause repeat failures that look like the lock itself is bad. It's also worth confirming the door boot/gasket is seated correctly, since a misaligned door can put uneven stress on the lock mechanism. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same locking mechanism, switch design, and harness connector as the door lock originally installed in your GE front-load washer or Ultrafast combo washer/dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

316233903 Oven Genuine Temperature Sensor Replaces Part Numbers:  316233903, 316217008, 316233902, 316233900, AP5998652, PS11731754. Description: This Oven Temperature Sensor is a Genuine part for select Frigidaire, Kenmore oven models. It monitors and regulates the oven's temperature by sending accurate temperature readings to the control board. This ensures that the oven maintains the desired cooking temperature throughout the baking or roasting process.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W10356257 Washer Genuine Water Valve Fits Specific Whirlpool, Maytag Washer Model Replaces Part Numbers: WPW10356257, W10356257, 1938138, W10336721, W10337338, W10352254, AP6020342, PS11753661. Description: This Water Inlet Valve is a Genuine part for specific Maytag, Whirlpool washing machine models. This part controls the flow of water into the washer during the filling cycles. This valve ensures that the correct amount of water is delivered to the tub, allowing for optimal washing performance. Common causes of a bad water inlet valve can include mineral buildup, electrical issues, or wear and tear from regular use.

Read more less

807047102 Range Genuine OEM Drawer Guide Fits Specific Frigidaire Range modles Replaces Part Numbers: 807047102, 316407301, 5304490937, 316407300, 4456932, AP6036410, PS11770783.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10455261 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers: WPW10455261, W10455261, 2312159, W10500284, AP6021679, PS11755005. California Residents only WARNING: California’s Proposition 65 

Read more less

XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat The XPARTCO 6931EL3001F is an aftermarket replacement dryer rear hi-limit heater thermostat compatible with select LG and Kenmore electric and gas dryers. The hi-limit thermostat is a safety switch mounted on the heater housing that monitors the temperature at the heating element. If the heater temperature exceeds the safe operating limit, the thermostat opens its contacts to cut power to the heating element, protecting the dryer and its contents from overheating. When cooled, the thermostat resets automatically — but if it fails internally, it may remain open permanently, causing the dryer to produce no heat despite the thermal fuse and other components being intact. Rated L125-31C, 250V, 25A, this 3-terminal thermostat measures 2"L x 1-3/4"W x 1-1/4"H with approximately 1-5/8" between mounting holes (center to center). It is constructed from metal and plastic in gray/black and mounts directly on the heater housing. It directly replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482, and PD00023316. Often replaced together with the 6931EL3003D thermal fuse — both mount on the heater housing and work as a system to protect the dryer from overheating. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat fixes LG and Kenmore dryers with no heat where the thermostat has failed open. Rated L125-31C, 250V/25A, 3 terminals. 2"L x 1-3/4"W x 1-1/4"H, ~1-5/8" between mounting holes. Mounts on heater housing. Test with multimeter — should show closed continuity at room temperature. Often replaced together with 6931EL3003D thermal fuse. Replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482. Common Problems This Part Fixes Dryer produces no heat — hi-limit thermostat has failed open and is permanently interrupting the heater circuit Dryer takes much longer than normal to dry a load Dryer tumbles normally but generates no heat during the cycle No heat even after the thermal fuse has already been replaced — thermostat also failed Dryer overheating intermittently — thermostat not opening at the correct temperature Multimeter test shows open circuit (no continuity) across the thermostat at room temperature Replaces Part Numbers This hi-limit thermostat directly replaces the following OEM and cross-reference part numbers: 6931EL3001F, 1377779, AH3530482, ALG51960, EA3530482, EAP3530482, AP5072172, PD00023316, PS3530482 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hi-limit thermostat is compatible with select LG and Kenmore electric and gas dryers. Compatible models include LG DLE, DLG, DLEX, DLGX, and DLB series dryers, and Kenmore 796-series dryers built on the LG platform. LG electric dryers — DLE series (DLE2050W, DLE3777W, DLE5955W and related models) LG electric dryers — DLEX series (select models) LG gas dryers — DLG series (DLG2051W, DLG3788W and related models) LG gas dryers — DLGX series (select models) LG electric and gas dryers — DLB series (select models) Kenmore / Sears dryers — 796-series (LG-built models) Tip: When replacing the 6931EL3001F thermostat, also replace the 6931EL3003D thermal fuse at the same time. Both mount on the heater housing and are commonly replaced together — an overheating event that causes one to fail typically stresses both. Key Features Hi-limit heater thermostat — safety switch that cuts power to the heating element if heater temperature exceeds safe limits Auto-resets when cooled — but a failed thermostat that remains open causes permanent no-heat Rated L125-31C, 250V, 25A — correct specifications for compatible LG and Kenmore dryers 3-terminal design — matches the original wiring configuration on compatible heater housings Dimensions: 2"L x 1-3/4"W x 1-1/4"H; ~1-5/8" between mounting holes (center to center) Metal and plastic construction (gray/black) — heat-resistant materials for heater housing application Mounts directly on the heater housing — accessible from the dryer back panel Often replaced together with 6931EL3003D thermal fuse for a complete heater housing thermal repair Test with multimeter before replacing — should show closed continuity at room temperature Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6931EL3001F Part Type Dryer Rear Hi-Limit Heater Thermostat Condition Aftermarket Replacement Application LG and Kenmore Electric and Gas Dryers Thermostat Rating L125-31C — auto-resets after cooling Voltage 250V Amperage 25A Terminals 3-terminal Dimensions 2"L x 1-3/4"W x 1-1/4"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Gray / Black Material Metal / Plastic Location Heater housing (rear of dryer) Normal Behavior Closed continuity at room temperature Often Replaced With 6931EL3003D Thermal Fuse Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heater housing. The 6931EL3001F thermostat is mounted on the heater housing — it is the 3-terminal component with gray/black housing. Before removing it, test it with a multimeter: disconnect the wires and probe the terminals. At room temperature a working thermostat shows closed continuity. An open reading confirms failure. Photograph the 3-wire connections before disconnecting — reconnecting in the correct positions is important. Remove the 2 mounting screws and lift the old thermostat off. Install the new thermostat in the same position with the 2 mounting screws and reconnect the wires in the same positions. While the heater housing is accessible, also test and replace the 6931EL3003D thermal fuse if needed. Reinstall the back panel, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, multimeter. Frequently Asked Questions What is the difference between the 6931EL3001F thermostat and the 6931EL3003D thermal fuse? Both are mounted on the heater housing and protect the dryer from overheating, but they work differently. The 6931EL3001F is a resettable hi-limit thermostat rated L125-31C — it opens when the heater temperature gets too high and resets automatically when cooled. The 6931EL3003D is a one-time thermal fuse that permanently interrupts the circuit if the temperature exceeds its rated limit — once blown, it cannot reset and must be replaced. Both should show closed continuity at room temperature when working. Because both are on the heater housing and experience the same thermal stress, replacing both at the same time is recommended. How do I test the 6931EL3001F thermostat with a multimeter? Unplug the dryer and disconnect all three wires from the thermostat terminals. Set your multimeter to continuity or resistance mode. At room temperature, a working 6931EL3001F thermostat should show closed continuity (near-zero resistance) across its contacts. If your multimeter reads open circuit (no continuity / OL), the thermostat has failed and needs replacement. Since this thermostat auto-resets when cooled, always test at room temperature — testing while the dryer is still warm may give a false open reading if the thermostat has legitimately opened due to heat. My LG dryer has no heat but the thermal fuse is good — could it be the thermostat? Yes — when the thermal fuse tests good but there is still no heat, the hi-limit thermostat (6931EL3001F) is the next most common culprit. A thermostat that has failed internally may remain permanently open even at room temperature, cutting power to the heating element exactly as a blown thermal fuse would. Test the thermostat with a multimeter for continuity. Also check the cycling thermostat (6931EL3002M) and the thermistor (6323EL2001B) — all three are part of the LG dryer thermal control system and any one of them can cause a no-heat condition. What does the "L125-31C" rating mean? The L125-31C rating describes the thermostat's operating parameters. L125 means the thermostat opens (trips) when the temperature reaches approximately 125°C (257°F). The 31 indicates the reset differential — the thermostat resets when the temperature drops approximately 31°C below the trip point, around 94°C (201°F). This rating ensures the thermostat allows the heater to operate at normal drying temperatures while protecting against dangerous overheating. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from metal and plastic to match the L125-31C rating, dimensions, and 3-terminal configuration of the original 6931EL3001F hi-limit heater thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less