Search results for "dryer thermal fuse"

XPARTCO WH05X24185 Washer Clutch The XPARTCO WH05X24185 is an aftermarket replacement clutch for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This clutch engages and disengages the transmission during the wash and spin cycles, transferring the motor's power to spin the basket so your clothes finish damp rather than soaked. Made of white plastic with a glossy finish, measuring approximately 3"L x 3"W x 1"H. Sold individually and does not include any other parts, such as the shift actuator (our WH03X30517 listing) that works alongside it. Common causes of failure include wear and tear over time, excessive load, or mechanical obstruction. Symptoms of a worn or failing clutch include clothes coming out wet even after a completed spin cycle, a slight burning odor during operation, or issues with spinning or agitating. It directly replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473. Quick Answer The XPARTCO WH05X24185 Washer Clutch fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers where clothes come out wet after spinning, there's a slight burning odor during operation, or the washer has trouble spinning or agitating. White plastic, glossy finish, ~3"L x 3"W x 1"H. Sold individually. Replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473. If you also see grease pooling on the floor under the washer, that's more likely a transmission gearcase leak than this clutch — and if the agitator only slips in one direction, check the agitator bolt before assuming the clutch has failed. Common Problems This Part Fixes Clothes coming out wet even after a completed spin cycle Slight burning odor during operation Washer having trouble spinning or agitating Reduced washer performance from clutch wear Grinding or unusual noise tied to the transmission area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer clutch directly replaces the following OEM and cross-reference part numbers: WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This clutch is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform. Note: This clutch is commonly replaced alongside our WH03X30517 shift actuator, since the two work together in the same wash/spin transition system, but they are sold separately. If your washer also isn't switching between agitation and spin, check the actuator as well. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement clutch — engages and disengages the transmission during wash and spin Resolves "clothes still wet," "burning odor," and "trouble spinning or agitating" symptoms White plastic, glossy finish Approximately 3"L x 3"W x 1"H Direct drop-in replacement matching the original mounting Replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Aftermarket replacement built to OEM-equivalent quality standards Sold individually Product Specifications Part Number XPWH05X24185 OEM Part Number WH05X24185 Part Type Washer Clutch Condition Aftermarket Replacement Color White Material Plastic Finish Glossy Dimensions Approx. 3"L x 3"W x 1"H Related Part WH03X30517 shift actuator (sold separately) Repair Difficulty Moderate — some disassembly required Quantity 1 clutch (sold individually) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning to cut off electricity and prevent accidental shocks. Wear work gloves. Remove the two screws at the back of the washer with a Phillips head screwdriver, then pull off the main console and carefully set it aside. Locate the access plate on the transmission side and remove the screws securing it. Take the belt off the pulley and remove the belt guard. Remove the four screws that secure the clutch and take it off from the wet end of the transmission. Install the new WH05X24185 clutch and replace the four screws. Reattach the belt, pulley, and access plate, and replace their screws. Put the main console back onto the washer and secure it with the two screws. Restore power and run a test cycle to confirm clothes are coming out properly damp at the end of the spin cycle, with no burning odor or unusual noise. Tools needed: Phillips screwdriver, socket wrench, work gloves. Frequently Asked Questions My clothes come out wet after the spin cycle. Is this the clutch I need? Yes, this is one of the most common symptoms of a worn or failing clutch. Since this clutch is what engages the transmission to spin the basket at high speed, a worn clutch can slip rather than fully engaging, leaving clothes wetter than they should be at the end of the cycle. A slight burning odor during operation is another documented sign of the same wear. I noticed grease on the floor under my washer. Is that this clutch leaking? Not directly — grease pooling under the washer typically comes from the gearcase transmission itself rather than the clutch. If you're seeing this symptom, the transmission may need attention in addition to, or instead of, this clutch, depending on what else you're experiencing. My agitator slips going one direction but not the other. Is that the clutch? Not necessarily. This specific symptom — the agitator pulling fine in one direction but slipping in the other — is more often traced to a loose agitator bolt. It's worth checking and tightening that bolt first; if the problem persists, the agitator base hybrid assembly may need inspection before assuming this clutch is at fault. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the material, dimensions, and mounting configuration of the original WH05X24185 clutch used in compatible GE, Hotpoint, Haier, Monogram, and Café top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

240597220 Genuine OEM Frigidaire Refrigerator Temperature Sensor The 240597220 is a Genuine OEM Frigidaire replacement refrigerator temperature sensor compatible with a wide range of Frigidaire, Electrolux, Kenmore (253/106/795 prefix), Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators and household freezers. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the main control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate temperatures. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time. When this sensor fails or drifts out of range, the refrigerator may run too cold or too warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display OP error codes. Rated 10K Ohm NTC, with a 5/16" diameter probe, 12" wire, and overall dimensions of 3-5/8"L x 5/8"W x 5/16"H (sensor probe itself measures ~1-3/16"L x 5/16" diameter). Compatible with 20-28 cubic foot North American household refrigerators in French door, side-by-side, top-freezer, and bottom-freezer configurations (post-2005 production). 240597220 is the current OEM part number, superseding 240597203, 240597201, and 240597202. It also replaces 7240597203, AP4032998, AP7243155, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, and PS17647917. Not compatible with mini fridges, car refrigerators, commercial units, wine coolers, or ice makers. Installs in 15–20 minutes with basic hand tools. Quick Answer The 240597220 Genuine OEM Frigidaire Refrigerator Temperature Sensor fixes Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, or display OP error codes. NTC thermistor — 10K Ohm at room temperature. 5/16" probe diameter, 12" wire. Overall 3-5/8"L x 5/8"W x 5/16"H. Genuine OEM. Supersedes 240597203, 240597201, 240597202. Also replaces 7240597203, AP4032998, AP7243155, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, PS17647917. For 20–28 cu ft household refrigerators built 2005 or later. Common Problems This Part Fixes Refrigerator running too cold or too warm — sensor not accurately reporting temperature Inconsistent temperatures — fluctuating cooling that can't maintain set point OP error code displayed on the control panel (open sensor circuit) Excessive frost or ice buildup on evaporator coils from erratic defrost timing Refrigerator running continuously without cycling off Freezer over-freezing food or fresh food compartment freezing groceries Food spoilage from temperature instability Multimeter test shows 0 ohms (shorted), infinite resistance (open), or drifted resistance instead of the expected ~10K Ohms at room temperature Replaces Part Numbers This temperature sensor is the current OEM part number and supersedes the following OEM and cross-reference part numbers: 240597220, 240597203, 240597201, 240597202, 7240597203, 4985585, AFR15666, AP7243155, EAP17647917, OEM21729474, PD00088922, PS17647917. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select household refrigerators and freezers from the following brands (20–28 cu ft, built 2005 or later): Frigidaire refrigerators — Gallery and Professional series, plus standard Frigidaire models (BFHS2611LM, BGHS2634KE, BGHS2634KP, BGHS2644KF, CRSH237LB, PRFG2383AF, PRFC2383AF, ERFG2393AS2, FRSS2323AS8, FFHB2740PP5A and many related models) Frigidaire upright freezers — FFFH21F7QW, FGU19F6QWB and related models Electrolux refrigerators — EI24RD65KS0, EI24RD65HS0, EI24RD65HS1, E24RD75KPS0 and related models Kenmore / Sears refrigerators — 253-prefix, 106-prefix, and 795-prefix models (select Frigidaire/Electrolux-built units) Crosley refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Kelvinator refrigerators (select models) Gibson refrigerators (select models) Tappan refrigerators (select models) Viking refrigerators (select Frigidaire-platform models) Ikea refrigerators (select Frigidaire-platform models) Not compatible with: mini fridges, car refrigerators, commercial refrigerators/freezers, wine coolers, or dedicated ice makers. Verify your refrigerator was produced after 2005 and check the original part number on the fridge nameplate matches one of the cross-references listed. Contact our support team with your model number if you're unsure. Key Features NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring Rated 10K Ohms at room temperature (approximately 25°C / 77°F) Sends real-time temperature data to the main control board to regulate compressor cycling, fan operation, and defrost timing Sensor probe: 5/16" diameter x 1-3/16" length · Overall assembly: 3-5/8"L x 5/8"W x 5/16"H · 12" wire lead White plastic/metal construction with glossy finish Resolves OP error codes when caused by an open sensor circuit Compatible with 20–28 cu ft French door, side-by-side, top-freezer, and bottom-freezer refrigerators built 2005 or later Current OEM part number — supersedes 240597203, 240597201, 240597202 and replaces AP4032998, AH1765215, PS1765215, PS17647917 and additional cross-references Compatible with Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications — guaranteed fit and performance Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 240597220 Supersedes 240597203, 240597201, 240597202 Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Household Refrigerators and Freezers (Frigidaire/Electrolux platform, 20–28 cu ft, 2005+) Sensor Type NTC (Negative Temperature Coefficient) Resistance 10K Ohms at room temperature Probe Dimensions 5/16" Diameter x 1-3/16" Length Overall Dimensions 3-5/8"L x 5/8"W x 5/16"H Wire Length 12" Color White Finish Glossy Material Plastic / Metal Error Codes Resolved OP (open sensor circuit) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Depending on your refrigerator model, the fresh-food temperature sensor is typically located behind the air tower or damper assembly on the rear interior wall of the refrigerator compartment; the freezer temperature sensor is typically located behind the rear freezer access panel near the evaporator coils. Confirm which sensor location matches your symptom and the parts diagram for your specific model before starting. Remove all shelves, drawers, and any items blocking access to the sensor location. Remove the screws holding the air tower/damper cover (fresh food side) or rear freezer access panel to expose the sensor. Photograph the sensor position, wire routing, and connector before removing. Disconnect the wire connector (gently — the connector can be fragile) and release the sensor from its mounting clip. Fully insert the new 240597220 sensor probe into the card slot (no exposure) and secure with the mounting clip. Reconnect the wire connector — plug wiring terminals tightly to avoid poor contact. Use cable ties to secure any loose wire routing as before. Reinstall the cover or panel, replace the shelves and drawers, and plug the refrigerator back in. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, cable ties, multimeter (for testing), work gloves. Frequently Asked Questions What does OP error code mean on my Frigidaire refrigerator? The OP error code (Open) indicates the control board is detecting an open circuit on a temperature sensor input — meaning the sensor is failing to send a resistance signal, either because the sensor itself has failed open internally, the wire has broken, or the connector isn't seated. Replacing the temperature sensor typically resolves the code when the sensor itself is the cause. If the code persists after replacement, check the wire harness between the sensor and the control board for damage, and confirm the connector is fully seated. If the OP code appears alongside other symptoms like frost buildup and cooling issues that persist after sensor replacement, the defrost temperature sensor (on the Harness-Low Side, a different part number) may also need to be replaced, or the main control board may be at fault. How do I test if the temperature sensor has failed? Unplug the refrigerator, disconnect the sensor's wire connector, and set your multimeter to resistance mode. At room temperature (approximately 25°C / 77°F), a working NTC thermistor should read approximately 10K Ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. If it reads significantly off from 10K (for example 8.4K or 5K at room temp), the sensor has drifted and is no longer providing accurate readings — replacement is recommended. Any of these results confirms the sensor needs replacement. My refrigerator has multiple temperature sensors — which one do I replace? Frigidaire refrigerators typically use multiple temperature sensors: one in the fresh food compartment (behind the air tower/damper), one in the freezer compartment (near the evaporator coils), and often a separate defrost temperature sensor on the Harness-Low Side. The 240597203 is used as the fresh food or freezer compartment temperature sensor. If your symptom is "fresh food too warm" or "freezer over-freezing," the fresh food sensor is the likely candidate. If your symptom is "freezer icing up despite defrost heater working," the defrost temperature sensor may be the culprit — a different part number. Check your refrigerator's parts diagram to confirm the correct sensor location for your specific symptom. Does this sensor fit my Kenmore refrigerator? On many Kenmore refrigerators, yes — Sears sells Kenmore-branded refrigerators that are manufactured by Frigidaire/Electrolux, Whirlpool, LG, and Samsung. The 240597203 sensor fits Kenmore refrigerators with model numbers beginning with the 253, 106, or 795 prefixes that are Frigidaire/Electrolux-built. Kenmore refrigerators built by other manufacturers (Whirlpool, LG, Samsung) use different sensors. Check the first three digits of your Kenmore model number — if it's 253, 106, or 795 and falls within the compatible model list, this is the correct part. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications. It is the exact same temperature sensor installed in compatible Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Choice DA32-10109Y Refrigerator Temperature Sensor – Replacement for Samsung Product Overview The DA32-10109Y Refrigerator Temperature Sensor is an aftermarket replacement part designed to measure and relay internal temperatures to the control board. A faulty sensor can lead to cooling problems, temperature fluctuations, or improper defrost cycles. Replacing a worn sensor with this reliable component helps restore accurate temperature readings and optimal cooling performance in your refrigerator. 8-1/4" overall length with two pin plug for freezer. Fits Samsung SXS refrigerator models. Replaces Part Numbers This sensor replaces part numbers DA32-10109Y, AP4136950, PS4138703. It is engineered to match the fit and functionality of the original Samsung sensor. Compatible Brands Compatible with many Samsung and Kenmore refrigerators manufactured by Samsung. Fits French door, bottom-freezer, and side-by-side models that use this temperature sensor. Fixes the Following Issues Refrigerator not cooling properly Freezer too warm or too cold Temperature reading errors Inconsistent cooling or defrost operation Why Buy from Parts‑O‑Matic Affordable and dependable aftermarket part Fast and free U.S. shipping Easy to install – no special tools required Trusted by appliance techs and DIYers

Read more less

W10503278 Refrigerator Control Board Refrigerator electronic (JAZZ) control board. Be aware the board will need to programmed after installation to work properly Replaces Part Numbers: WPW10503278, 12784415, W10503278, 12002339, 12002445, 12002449, 12002508, 12002509, 12002567, 12002706, 12784415V, 12868502, 12868510, 12868513, 2684578, 67003867, 67004453, 67004496, 67004907, 67005043, 67005280, 67005281, 67006034, 67006209, 67006214, 67006216, 67006226, 67006712, 67006740, 8208187, AP6022400, PS11755733, W10165748. Description: This Electronic Control Board is a replacement part for Specific Maytag, Whirlpool refrigerator models. This Electronic (JAZZ) Control Board manages various functions of your refrigerator, ensuring proper temperature control and operation. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W10876600 Washer Genuine OEM Drain Pump – Compatible with Whirlpool, Maytag, Amana, and Crosley Washers Product Description Quickly and efficiently remove water from your washer with the W10876600 Washer Genuine OEM Drain Pump. This factory-approved replacement pump removes water from the tub during wash and spin cycles, ensuring smooth performance and proper draining. A faulty drain pump can cause standing water, error codes, or incomplete cycles. Replacing it with this Genuine OEM part restores dependable drainage and long-lasting washer performance. Replaces Part Numbers W10876600, 4455877, W10727777, W10876600VP, PD00034529, EAP11738156, AP6004933, PS11738156. Compatibility This Genuine OEM drain pump fits select Whirlpool, Maytag, Amana, and Crosley top-load and front-load washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC465HW0, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Factory-approved for perfect fit and reliable operation 💧 Efficient Water Removal – Quickly drains water from the washer tub after each cycle 💪 Durable Motor Design – Built to withstand repeated use and heavy loads 🛠️ DIY Installation – Direct-fit replacement installs easily with basic tools 🛡️ Fixes Common Issues – Solves washer not draining, standing water, or “F9E1”/“SD” error codes 📐 Product Specification Part Number: W10876600 Component Type: Washer Drain Pump Assembly Material: Heavy-duty plastic pump housing and electric motor Voltage: 120V AC Mounting: Direct-fit on washer base with wiring harness connection Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Nut driver, pliers, towel or bucket ⚠️ Safety First: Always unplug the washer and disconnect water supply before performing repairs to prevent electrical shock or leaks. Steps: Disconnect power and water hoses. Tilt the washer back or remove the front access panel. Unplug the wiring harness and loosen the clamps on the drain hoses. Remove the old pump and install the new W10876600 pump. Reconnect hoses and wiring, secure the pump, and restore power. Run a rinse or drain cycle to verify proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Fix washer drainage issues fast — Add to Cart Now for a factory-quality repair that lasts!

Read more less

XPARTCO 242278801 Refrigerator Temperature Sensor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Keep your refrigerator cooling accurately with the XPARTCO 242278801 Refrigerator Temperature Sensor. This high-quality replacement monitors the temperature inside the fresh-food and freezer compartments, sending signals to the control board to regulate cooling. A faulty sensor can cause temperature fluctuations, over-freezing, or warm spots. Replacing it with this reliable XPARTCO part ensures consistent temperature control and energy-efficient performance. Replaces Part Numbers 242278801 PD00029820, EAP8760187, AP5802148, 3016441, PS8760187. Compatibility This replacement temperature sensor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to): Frigidaire FFHS2611LBNA, Electrolux E23BC78IPS3, and Kenmore 253.7041341C. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Accurate Cooling Control – Monitors refrigerator temperature for consistent performance 💰 Cost-Effective Fix – Reliable alternative to expensive OEM parts 🛠️ Simple Installation – Plug-in design for fast, easy replacement 🛡️ Fixes Common Issues – Solves warm refrigerator, freezing, or inconsistent cooling problems 📐 Product Specification Part Number: 242278801 Component Type: Refrigerator Temperature Sensor (Thermistor) Material: Plastic housing with thermistor probe and wiring harness Resistance Range: Approximately 2.7 kΩ at 77°F (varies by temperature) Mounting: Direct-fit installation in refrigerator liner or evaporator area Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, wire clip removal tool ⚠️ Safety First: Always unplug the refrigerator before servicing to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the old temperature sensor, usually near the evaporator or rear wall. Disconnect the sensor’s wiring harness and remove clips. Install the new XPARTCO 242278801 sensor in the same position. Reconnect wiring, reassemble interior parts, and restore power. Allow several hours for the refrigerator to stabilize temperature. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator cooling efficiently — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO DA32-10105X Refrigerator Temperature Sensor – Compatible with Samsung and Kenmore Refrigerators Product Description Maintain consistent cooling performance with the XPARTCO DA32-10105X Refrigerator Temperature Sensor. This high-quality replacement monitors internal refrigerator temperature and communicates with the control board to regulate cooling cycles. A faulty sensor can cause temperature fluctuations, frost buildup, or over-cooling. Installing this reliable XPARTCO sensor helps restore accurate temperature readings and energy-efficient operation. Replaces Part Numbers DA32-10105X, 2030345, PD00002045, EAP4138686, AP4338786, PS4138686 Compatibility This replacement temperature sensor fits select Samsung and Kenmore refrigerators. Example compatible models include (but are not limited to): Samsung RF28HMEDBSR/AA, RF23HCEDBSR/AA, and Kenmore 795.72053.112. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM accuracy and reliability ❄️ Precision Cooling Control – Ensures stable refrigerator and freezer temperatures 💰 Budget-Friendly Fix – Provides OEM-level performance at a lower cost 🛠️ Easy Installation – Plug-in design for fast and simple replacement 🛡️ Fixes Common Issues – Solves cooling inconsistencies, frost buildup, or warm compartment problems 📐 Product Specification Part Number: DA32-10105X Component Type: Refrigerator Thermistor (Temperature Sensor) Material: Plastic sensor probe with insulated wiring harness Mounting: Clip-in or taped to evaporator wall depending on model Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the existing temperature sensor near the evaporator coil or rear wall. Unplug the old sensor from its wiring harness. Install the new XPARTCO DA32-10105X sensor and reconnect the harness. Secure the sensor in place with clips or adhesive as applicable. Reassemble interior panels and restore power. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator running efficiently — Add to Cart Now for a reliable, cost-effective repair!

Read more less

Genuine OEM W11353813 Refrigerator Control Box Assembly The Genuine OEM Whirlpool W11353813 is the control box assembly for select Whirlpool top-mount refrigerators. It houses the temperature controls that set the refrigerator and freezer temperatures from one location. Replace it when the controls no longer respond, the temperatures can't be adjusted or held, or the box is cracked or damaged. This is the original Whirlpool part, not an aftermarket equivalent. It is sold as an assembly, which may include more than one component, so check the parts diagram for your model to confirm it matches what you need to replace. Quick Answer The Genuine OEM W11353813 Refrigerator Control Box Assembly replaces a faulty or damaged temperature control box on a compatible Whirlpool top-mount refrigerator. Replaces W10869714, W10884375, W11039821, W11211884 and W11223731. Classic symptoms: the temperature controls don't respond, or the refrigerator and freezer temperatures can't be adjusted or held. When To Replace This Part Temperature controls that don't respond or can't be adjusted Refrigerator or freezer temperatures that won't hold at the setting Cracked or damaged control box Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This control box assembly replaces or supersedes the following part numbers: W11353813  •  W10869714  •  W10884375  •  W11039821  •  W11211884  •  W11223731 If your old control box shows a different number, contact our support team and we'll check whether it matches. Compatibility This control box assembly is listed for Whirlpool top-mount refrigerators, including these examples: Whirlpool WRT519SZDM06, WRT519SZDD01, WRT519SZDG04, WRT519SZDD06 Whirlpool WRT519SZDT06, WRT519SZDW01, WRT519SZDW05, WRT549SZDM03 Whirlpool WRT138FZDB00, WRT138FZDM00, WRT318FZDM00, WRT519SZDW00 Note: The models above are a sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Control box assembly that houses the refrigerator and freezer temperature controls Replaces five earlier Whirlpool part numbers Sold individually Product Specifications Part Number W11353813 OEM Part Number W11353813 Part Type Refrigerator Control Box Assembly Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Assembly Application Select Whirlpool Top-Mount Refrigerators Installation Notes ⚠️ Unplug The Refrigerator First Unplug the refrigerator before you start, and take a photo of the wiring connections before disconnecting anything. Transfer the connectors to the new assembly one at a time, matching the original positions, then secure it and restore power. The assembly may include multiple parts, so check the parts diagram for your model to confirm what comes with it. If the problem remains, the cause may be a different component such as a sensor or the main control board. Frequently Asked Questions My refrigerator isn't cooling right. Is this the fix? Only if the temperature controls in this box are the problem. Poor cooling can also come from sensors, fans or other control components, so confirm the cause before replacing it. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. What comes in the assembly? It is a control box assembly and may include more than one part. Check the parts diagram for your model, or contact our support team and we'll confirm before you order. Will this fit my refrigerator? It is listed for many Whirlpool top-mount refrigerators, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11168740 Washer Water Valve (Cold Side) The XPARTCO W11168740 is an aftermarket replacement cold water inlet valve for Whirlpool-built top-load washers, located on the top back of the cabinet where the hot and cold supply hoses connect. Unlike its companion hot-side valve (sold separately as W11168743, a single-solenoid design), this cold valve uses two internal solenoid coils in one blue-bodied housing. When the control calls for a cold fill, it energizes the appropriate solenoid to open the water path; once the correct level is reached, it closes again. Because it's a dedicated cold-only valve, a failure here produces a distinctive symptom: cold-only fills stop working, slow down dramatically, or don't stop when they should, while hot fills (governed by the separate hot valve) continue working independently. Rated 120V, 60Hz, with push-on outlet connections sealed by rubber grommets. Common failure causes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn seal at the outlet connection. It directly replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, and PS12348073. Quick Answer The XPARTCO W11168740 Washer Water Valve (Cold Side) fixes Whirlpool-built top-load washers where cold water won't fill, fills slowly, keeps filling and won't stop, leaks, or throws a fill-related error code — while hot water fills normally. Blue-bodied, 2-solenoid cold-only valve, 120V, 60Hz, push-on outlet with rubber grommets. Replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, PS12348073. This is the cold-side valve only — the companion hot-side valve is sold separately as W11168743. Common Problems This Part Fixes Washer won't fill with cold water while hot water fills normally Cold water fills much more slowly than it used to Washer keeps filling with cold water and won't stop, leading to overfill Water leaking at the cold connection point Fill-related error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash Cold wash or cold rinse cycles specifically affected while other cycles run fine Water pooling underneath or behind the washer near the cold supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168740, WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including: Whirlpool top-load washers — WTW series Maytag top-load washers (select Whirlpool-built models) Select Kenmore top-load washers built on the Whirlpool platform Verified model numbers include: WTW5500XL0, WTW5500XL2, and WTW5640XW3. Note — cold side only: This is the cold water valve, identifiable by its blue body and two internal solenoids. The matching hot water valve for these same washers is sold separately under part number W11168743 — a single-solenoid design. The two are not interchangeable. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement dedicated cold water inlet valve for Whirlpool-built top-load washers Two internal solenoid coils in one blue-bodied housing, identifiable at a glance from the single-solenoid hot valve Resolves "won't fill with cold water," "fills slowly," "won't stop filling," and "leaking at the connection" symptoms caused by valve failure Rated 120V, 60Hz Push-on outlet connections sealed with rubber grommets Approximately 3-3/8"L x 3-1/2"W x 2-3/8"H Direct drop-in replacement — no modification required Replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, and PS12348073 Compatible with a wide range of Whirlpool, Maytag, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW11168740 OEM Part Number W11168740 Part Type Washer Water Inlet Valve — Cold Side Condition Aftermarket Replacement Application Top-Load Washers (Whirlpool-Built) Voltage 120V Frequency 60 Hz Solenoids 2 (dedicated cold water function) Color Blue / Teal / Black Material Plastic and metal Outlet Connection Push-on with rubber grommets Dimensions Approx. 3-3/8"L x 3-1/2"W x 2-3/8"H Companion Part W11168743 (hot water valve, sold separately) Quantity 1 valve Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply hose from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the screws securing the top panel (a 1/4" nut driver or socket handles most models), then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit next to each other and it's easy to cross a wire. Disconnect the electrical connector(s) from the old cold valve, disconnect the push-on outlet hose (check the rubber grommet for wear and replace it if it looks flattened or cracked), remove the two mounting screws holding the valve, and pull it free — leave the hot valve (W11168743) undisturbed if it isn't also being replaced. Install the new W11168740 in the same position, secure the mounting screws, reconnect the electrical connector(s), and press the outlet hose back onto its fitting with the grommet properly seated. Reattach the cold water supply hose, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm cold water fills at the normal rate, and stops when it should, with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, Phillips screwdriver, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Cold water won't fill but hot water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Since your washer uses separate hot and cold valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve keeps working independently. If cold-specific cycles are the ones failing while hot cycles are unaffected, this cold-side valve is the correct part to replace. How can I tell this valve apart from the hot-side valve just by looking at it? This cold valve has a blue body and two internal solenoid coils, while the companion hot-side valve (W11168743) is a single-solenoid design. If you're staring at the old valve trying to confirm which one you're removing, the color and solenoid count are a quick visual check. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11168740 valve alone is sufficient. Some people choose to replace both while the top panel is already off, especially on an older washer, but it isn't required. My washer keeps filling with cold water and won't stop. Is that dangerous? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dual-solenoid design, connection type, and dimensions of the original W11168740 cold water valve used in compatible Whirlpool, Maytag, and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10528947 Washer Drive Hub Kit The XPARTCO W10528947 is an aftermarket replacement washer basket drive hub kit compatible with select top-load washing machines from Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, and Inglis. The drive hub is a critical transmission component that connects the spin basket to the spin shaft, transferring power from the motor to rotate the wash basket and agitate laundry during each cycle. This kit includes one basket drive hub and one drive block retainer — everything needed to restore proper spinning and agitation function. Common causes of drive hub failure include normal wear over time, strain from heavy or unbalanced loads, and physical damage from impact. A worn or cracked hub typically results in the basket slipping, failing to spin, or producing loud clicking and grinding noises during operation. Quick Answer The XPARTCO W10528947 Washer Drive Hub Kit fixes washers that won't spin, spin weakly, make clicking or grinding noises, or leave clothes too wet after the cycle. It connects the spin basket to the spin shaft and is compatible with select Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, and Inglis top-load washers. Common Problems This Part Fixes Washer not spinning or agitating at all Weak or slow spin — clothes coming out too wet Clicking, grinding, or loud noises during spin cycle Basket slipping under load Washer pumping but not spinning Excessive shaking or movement during operation Replaces Part Numbers This kit directly replaces the following OEM and cross-reference part numbers: W10528947, 2684908, W10396887, W10528947VP, W11771931, EAP6012095, AWP40580, PD00024946, AP5665171, PS6012095. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive hub kit is compatible with select top-load washers from the following brands: Whirlpool top-load washers Maytag top-load washers (including Bravos series) Kenmore top-load washers (select models) Amana top-load washers Admiral top-load washers Crosley top-load washers Inglis top-load washers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Connects the spin basket to the spin shaft — restoring proper agitation and spin performance Aftermarket replacement built to OEM-equivalent quality standards Kit includes one basket drive hub and one drive block retainer for a complete repair Made from durable plastic construction designed to withstand regular wash cycle stress DIY-friendly repair — installs with basic hand tools in 30–60 minutes Budget-friendly alternative to OEM at a lower cost without sacrificing performance Product Specifications Part Number W10528947 Part Type Washer Basket Drive Hub Kit Condition Aftermarket Replacement Application Top-Load Washing Machine Material Durable Plastic (ABS) Hub Dimensions 3-5/8" Diameter x 13/16" H Retainer Clip Length 2-7/8" Kit Includes 1 Basket Drive Hub + 1 Drive Block Retainer Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, Inglis Installation Notes ⚠️ Safety First — Disconnect Power and Water Before Starting Unplug the washer from the power source and shut off the hot and cold water supply valves before beginning any repair. Remove the agitator or impeller (depending on your model) to access the drive hub. Unscrew the old hub and retainer, install the new drive hub kit in the same position, and reassemble the washer. Tools needed: multi-bit screwdriver, 7/16-inch socket with extension, and a nut driver. Allow 30–60 minutes for a complete repair. Consult your washer's service manual for model-specific instructions. Frequently Asked Questions Will the W10528947 fit my washer? This kit is compatible with select top-load washers from Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, and Inglis. Always verify your washer's model number before ordering. Contact our support team if you need help confirming compatibility. What does the drive hub do? The drive hub connects the spin basket to the spin shaft beneath the agitator. It transfers power from the motor to rotate the wash basket during the spin and agitation cycles. When the hub wears out or cracks, the basket can slip or stop spinning entirely. What are the signs that my drive hub needs replacement? Common signs include: the washer won't spin or agitate, the spin cycle is weak or slow, clothes come out too wet, or you hear clicking and grinding noises during operation. Excessive shaking or movement during the cycle can also indicate a worn hub. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable, long-lasting performance at a more affordable price point. What is included in the kit? The kit includes one basket drive hub and one drive block retainer — the two components needed for a complete drive hub replacement. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 5304517886 Refrigerator / Freezer LED Light Bulb – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Restore bright, energy-efficient interior lighting with the XPARTCO 5304517886 Refrigerator / Freezer LED Light Bulb. This high-quality aftermarket replacement provides clear, long-lasting illumination inside the refrigerator and freezer compartments. A failed LED bulb can cause dim or no lighting, making it difficult to see stored food. Replacing it with this XPARTCO LED bulb ensures reliable brightness while consuming less energy than traditional bulbs. Replaces Part Numbers 5304517886, 216846400, 216518101, 5304510893, 240588001, 241552807, 297114000, 5304498578, 5304509249, 5304520040, 216222700, 216518100, 216608600, 216988000, 216988100, 241552801, 3091423, 4929381, 5303091423, 5304495326, 7216988100, 7241552801, 7297114000, C000501867, F000092472, KEI D28M, KEID28M, KEL 2815, KEL2815, AC100-265V 3.8W, PD00051346, EAP12712277, AP6873911, PS12712277. Compatibility This replacement LED light bulb fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to):Frigidaire FFSS2615TS0, FGHC2331PF5Electrolux EI23CS55GS1Kenmore 253.7031321A Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM brightness and fit 💡 Bright LED Illumination – Daylight 5000k, Clearly lights refrigerator and freezer interiors ⚡ Energy Efficient – Low power consumption with long service life 🛠️ Plug-and-Play Installation – Direct-fit bulb installs in minutes 🛡️ Fixes Common Issues – Solves dim lighting, flickering, or no interior light 📐 Product Specification Part Number: 5304517886 Component Type: Refrigerator / Freezer LED Light Bulb Light Type: LED Color Temperature: Cool white, Daylight 5000k Mounting: Twist-in or clip-in base (model dependent) Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: None (gloves recommended) ⚠️ Safety First: Unplug the refrigerator or turn off power before replacing the light bulb. Steps: Disconnect power to the refrigerator. Remove the light cover, if applicable. Remove the old LED bulb. Install the new XPARTCO 5304517886 LED bulb securely. Reinstall the cover and restore power. Confirm proper illumination. ⏱️ Time Required: 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Brighten your refrigerator interior again — Add to Cart Now for a simple, cost-effective lighting upgrade!

Read more less