Search results for "Dryer Motors"

XPARTCO DC96-00887C - DC47-00018A Dryer Thermostat Set The XPARTCO DC96-00887C / DC47-00018A is an aftermarket replacement 2-piece thermal protection set for Samsung and select Kenmore electric dryers. These two components sit in different locations along the same heating circuit and guard against overheating in different ways. The DC47-00018A is a true cycling high-limit thermostat — it opens at approximately 260°F to cut power to the heating element, then automatically closes again once the temperature drops to around 210°F, letting the dryer resume heating without any part replacement needed. The DC96-00887C, despite frequently being labeled a "thermostat" by third-party sellers, is actually a one-time thermal fuse mounted with its bracket on the blower housing — once it opens from excess heat, it stays open permanently and must be physically replaced. Because these two parts monitor different points in the same circuit, they tend to be replaced together when a dryer has been running hot: if the high-limit thermostat has been cycling excessively or failed to catch a temperature spike, the downstream thermal fuse can end up blowing as the last line of defense. Symptoms of failure in this circuit include no heat or insufficient heat, drying that takes too long, the dryer shutting off too soon, or the timer failing to advance. It directly replaces DC96-00887A, AP5966894, 2074129, AP4207819, PS4216838, EAP4216838, WP35001193, 35001193, PS11741822, PS11741829, AP6008689 (DC96-00887C); and 35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682, WP35001092 (DC47-00018A). Quick Answer The XPARTCO DC96-00887C - DC47-00018A Dryer Thermostat Set fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, premature shutoff, or a timer that won't advance. Set includes the DC47-00018A cycling high-limit thermostat (260°F open / 210°F reset) and the DC96-00887C thermal fuse with bracket. Replaces the full cross-reference sets listed below for both parts. Despite common marketplace labeling, the DC96-00887C is a one-time thermal fuse, not a resettable thermostat — it must be replaced once it blows, while the DC47-00018A resets itself automatically. What's In This Set Component Type Function DC47-00018A Cycling High-Limit Thermostat Opens at ~260°F to cut heat, automatically resets and closes again around 210°F. No replacement needed after each trip. DC96-00887C Thermal Fuse (with bracket) Mounted on the blower housing. Permanently opens if temperature exceeds safe limits. Cannot reset — must be replaced once blown. Common Problems This Set Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat/thermal fuse set directly replaces the following OEM and cross-reference part numbers: DC96-00887C, DC96-00887A, AP5966894, PS4276292, WP35001193, 35001193, AP6008689, PS11741829, DC47-00018A, AP4201898, PS4205217, 35001092, WP35001092 AP6008682, PS11741822, EXPDC47-00018A, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This set is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note: Always verify your full model number before ordering, since Samsung uses several different thermal protection components across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features 2-piece set covering both the cycling high-limit thermostat and the blower housing thermal fuse DC47-00018A thermostat opens at approximately 260°F and resets automatically around 210°F DC96-00887C thermal fuse ships with its mounting bracket included Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Addresses two failure points in the same overheat-protection circuit at once No special tools required for installation Replaces the full cross-reference sets for both DC96-00887C and DC47-00018A listed above Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Set Contents 1x DC47-00018A high-limit thermostat, 1x DC96-00887C thermal fuse with bracket Condition Aftermarket Replacement Application Samsung Electric Dryers DC47-00018A Type Automatically resetting, cycling high-limit thermostat DC47-00018A Open Temperature ~260°F DC47-00018A Reset Temperature ~210°F DC96-00887C Type One-time thermal fuse — non-resettable DC96-00887C Location Blower housing Repair Difficulty Easy to Moderate — no special tools required Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Note Which Component Goes Where Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the blower housing and heater duct assembly where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermal fuse and thermostat can look similar at a glance and are easy to install in the wrong position. Test each old component with a multimeter for continuity if you want to confirm which has actually failed before replacing both — the DC47-00018A thermostat and DC96-00887C fuse can each be checked this way. Remove each old component from its mounting position, noting orientation and location, and disconnect its wiring. Install the DC47-00018A thermostat and the DC96-00887C fuse (with its bracket) from this set in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), multimeter (recommended), work gloves. Frequently Asked Questions Is DC96-00887C really a thermostat, or something else? Different sellers call it different things. This is a genuinely common point of confusion in the marketplace, and it's worth clearing up: DC96-00887C is actually a one-time thermal fuse mounted with its bracket on the blower housing, even though many third-party listings label it a "thermostat." The distinction matters for how you diagnose and handle it — once this fuse blows from excess heat, it stays open permanently and must be physically replaced, unlike a true thermostat (like the DC47-00018A in this same set) which resets itself automatically once things cool down. Why replace both parts together instead of just the one that failed? These two components sit at different points in the same overheat-protection circuit, and a problem with one often puts stress on the other. If the high-limit thermostat has been cycling excessively or didn't catch a temperature spike in time, the downstream thermal fuse can end up blowing as the last line of defense. Replacing both together addresses the full circuit rather than risking a second failure and a second repair shortly after. My dryer shuts off before the load is fully dry. Is that this set? It's a strong possibility. If the high-limit thermostat is tripping prematurely — opening at a lower temperature than it should, or failing to reset properly — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat set addresses. Is this an OEM or aftermarket set? This is an aftermarket replacement set built to OEM-equivalent quality standards. It is not a genuine Samsung OEM set, but each component is manufactured to match the electrical specifications, opening/reset temperatures, and mounting configuration of the original DC96-00887C thermal fuse and DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279816 Dryer Thermostat Kit The XPARTCO 279816 is an aftermarket replacement thermal fuse and high-limit thermostat combo kit for Whirlpool-built dryers. These are the dryer's two thermal safety devices, and they're bundled together in this kit because they tend to fail around the same time and share a common cause: restricted airflow that lets heat build up beyond safe levels. The high-limit thermostat is the first line of defense, opening at approximately 250°F (L250-80F) to interrupt heating if the dryer runs too hot. If that isn't enough to bring the temperature back down, the thermal fuse is the final failsafe, opening permanently at approximately 309°F to cut power to the dryer entirely. That's an important distinction between the two parts: the high-limit thermostat is a cycling safety device that can open and close as temperature rises and falls, while the thermal fuse is a one-time device — once it blows, it's done, and the dryer won't run again until it's replaced. This kit includes both components plus mounting screws and a wiring set with a jumper wire and extra terminals, which is used specifically when replacing an older-style thermostat that had a wire pressing directly onto the heating element. A dryer that won't start at all, with no lights or response, usually means the thermal fuse has blown; a dryer that runs but won't heat, or that stops heating partway through a cycle, points more toward the thermostat. It directly replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299. Quick Answer The XPARTCO 279816 Dryer Thermostat Kit fixes Whirlpool-built dryers that won't start at all, won't heat, or stop heating partway through a cycle. Includes a thermal fuse (opens ~309°F), a high-limit thermostat (opens ~250°F), mounting screws, and a wiring set. Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, PS334299. Always inspect and clean the dryer venting when replacing this kit — a blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer runs and tumbles but produces no heat Dryer heats for a while, then stops heating partway through a cycle Dryer that stopped working suddenly, especially after running unusually hot Clothes coming out extremely hot right before the dryer stopped heating or stopped entirely Repeated blown fuses or tripped thermostats on a dryer with a known venting restriction Continuity test shows an open circuit across the old fuse or thermostat Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279816, 279816VP, 3399848, 3977393, PD00002348, AWP39198, EAP334299, AH334299, EA334299, AP3094244, PS334299. 3977393 is the thermal fuse component and 3390291 is the "new-style" high-limit thermostat component included in this kit. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED series Maytag electric and gas dryers — NED series (select Whirlpool-built models) Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, and Roper dryers (select models) Kenmore and KitchenAid dryers (select Whirlpool-built models) Verified model numbers include: WED6200SW1, NED4600YQ0, NED4600YQ1, NED4655EW1, and LER3624EQ. Note: The wiring set included in this kit is designed for replacing an older-style thermostat that used a wire pressed directly onto the heating element. If your dryer uses the true old-style push-on thermostat and fuse combination (part 3977767), you'll need a different kit (commonly listed as APN197) instead of this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which kit fits your dryer. Key Features Complete combo kit — thermal fuse, high-limit thermostat, mounting screws, and wiring set in one package Thermal fuse opens at approximately 309°F as a one-time, non-resettable safety cutoff High-limit thermostat opens at approximately 250°F (L250-80F) as a cycling safety device Resolves "won't start at all," "runs but doesn't heat," and "stops heating mid-cycle" symptoms Wiring set includes jumper wire and extra terminals for older-style push-on thermostat connections Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299 Compatible with Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, and KitchenAid dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 279816 OEM Part Number 279816 Part Type Dryer Thermal Fuse & High-Limit Thermostat Kit Condition Aftermarket Replacement Kit Contents Thermal fuse, high-limit thermostat, mounting screws, wiring set Thermal Fuse Opening Temp Approx. 309°F (one-time, non-resettable) High-Limit Thermostat Opening Temp Approx. 250°F / L250-80F (cycling) Wiring Set Jumper wire + extra terminals for older-style push-on thermostats Quantity 1 kit Compatible Brands Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, KitchenAid Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing area where both the thermal fuse and high-limit thermostat are mounted, usually close together near the heating element or blower assembly. Photograph the wiring before disconnecting anything, and note whether your old thermostat used a push-on wire connection at the heating element — if so, use the included jumper wire and extra terminals to make the new connection correctly. Remove the mounting screws holding each old component in place and disconnect their wire terminals. Before installing the new parts, test the old fuse and thermostat with a multimeter to confirm which one (or both) is actually open, rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Install the new thermal fuse and thermostat from this kit in the same mounting positions, reconnect the wire terminals (using the included wiring set if applicable), and secure the mounting screws. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions Why does this kit include two different parts instead of just one? The thermal fuse and high-limit thermostat work together as a two-stage safety system, and they're bundled because they commonly fail together — both are reacting to the same underlying overheating condition, usually restricted airflow. The high-limit thermostat trips first at a lower temperature and can cycle open and closed; if that's not enough to control the heat, the thermal fuse trips at a higher temperature and shuts the dryer down permanently until replaced. Replacing both together addresses the full safety chain rather than just one link in it. My dryer won't start at all versus my dryer runs but doesn't heat — which part is which? A dryer with absolutely no response — no lights, no tumbling, nothing — usually points to the thermal fuse, since it's wired to cut power more broadly when it blows. A dryer that tumbles and runs normally but produces no heat, or that starts heating and then stops partway through, points more toward the high-limit thermostat. Testing both components with a multimeter will confirm exactly which one has failed. I replaced both parts and the dryer failed again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Neither of these parts fails from age; they trip or blow because the dryer overheated. If new parts fail again, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the parts still fail, have the heating element checked as well, since a shorted element can also drive excess heat. Do I need the wiring set included in this kit? Only if your dryer's original thermostat used a wire that pressed directly onto the heating element (an older-style connection) rather than a standard push-on terminal. If your dryer already uses a straightforward terminal connection, you can skip the jumper wire and extra terminals and connect the new thermostat directly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the opening temperatures, terminal configuration, and mounting positions of the original 279816 thermal fuse and high-limit thermostat kit used in compatible Whirlpool, Maytag, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10112954 Dryer Drum Belt Replaces WPW10112954 The XPARTCO W10112954 is an aftermarket replacement dryer drum belt compatible with select Whirlpool, Maytag, Amana, Kenmore, and Crosley dryers. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from durable rubber, this 5-rib Multi-V belt measures 93-1/4 inches long x 5/16 inch wide x 1/8 inch high and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It is a direct drop-in replacement for OEM part numbers WPW10112954 and W10112954, and also replaces W10131172 on compatible models. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W10112954 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer during operation. Compatible with select Whirlpool, Maytag, Amana, Kenmore, Crosley, and Admiral dryers. Measures 93.38" with 5 ribs and 4 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) Crosley dryers Admiral dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 93-1/4" length x 5/16" width x 1/8" height — 5-rib Multi-V design for a secure, slip-free grip on the pulleys Made from durable rubber — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers WPW10112954 and W10112954 — no modification required Also replaces W10131172 on compatible models Compatible with Whirlpool, Maytag, Amana, Kenmore, Crosley, and Admiral dryers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10112954 OEM Part Number WPW10112954 Part Type Dryer Drum Drive Belt (5-Rib Multi-V) Condition Aftermarket Replacement Application Gas and Electric Dryers Length 93-1/4 inches Width 5/16 inch Height 1/8 inch Ribs 5 ribs, 4 grooves Material Rubber Color Black Compatible Brands Whirlpool, Maytag, Amana, Kenmore, Crosley, Admiral Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum belt, remove the top panel and front panel of the dryer. Lift the drum out of the cabinet, remove the old belt, and loop the new W10112954 belt around the drum with the ribbed side facing inward toward the drum. Route the belt around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific repair video for the correct belt path around the pulleys. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the drum is out, inspect and replace the idler pulley and drum support rollers if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What is the difference between W10112954 and WPW10112954? These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954 number. Both refer to the identical drum belt — this aftermarket replacement is compatible with both. How does the W10112954 differ from the W10205415 belt? Both are 5-rib Whirlpool-family belts, but they differ slightly in length and width. The W10112954 is 93-1/4" long x 5/16" wide. The W10205415 is 92" long x 3/8" wide. They are not interchangeable — always use the part number specific to your dryer model. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor runs and you can hear it humming, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is partially broken or slipping. Open the dryer cabinet to visually inspect the belt and confirm if it is broken, frayed, or stretched out of shape. Does the W10112954 also replace W10131172? Yes — the W10112954 belt replaces W10131172 on compatible models. Both are 5-rib Whirlpool-family drum belts used across similar model ranges. Always verify your specific model number to confirm the correct belt before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from durable rubber to match the dimensions and performance of the original WPW10112954 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4400EL2001F Dryer Drum Belt – Compatible with LG & Kenmore Dryers Product Description Restore proper drum rotation and reliable drying performance with the XPARTCO 4400EL2001F Dryer Drum Belt. This high-quality replacement belt, designed for select LG and Kenmore dryers, connects the motor pulley to the drum and idler pulley, enabling efficient tumbling during drying cycles. Made of durable rubber with a 4-rib, 3-groove design, it fixes issues like the drum not turning, loud banging or squeaking noises, or extended drying times due to a worn or broken belt. Note: Includes one 92-inch belt. Inspect drum rollers, idler pulley, and drum for wear during replacement. Clean lint from the drum and cabinet to prevent overheating. Overloading the dryer can cause premature belt failure. Replaces Part Numbers 4400EL2001F, 4400EL2001A, AP4436354, 4PH2337, PS3522928, 4400EL2001C, 4400EL2001E, PD00026116, EAP11705916, AP5972814, PS11705916. Compatibility This replacement dryer drum belt fits select LG and Kenmore (LG-manufactured) electric dryers. Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, DLGX3571W, DLE7200WE, DLEX3570V, DLEX3570W, DLEX7600KE, DLEX7600WE, DLEY1901KE, DLEY1901WE, DLG4971W, DLGX5781VE, DLGX5781WE, DLGX7601KE, DLGX7601WE, DLGY1702V, DLGY1902KE, DLEX5101V, DLE5955W, DLE5977S, DLE0442W, DLGX3371V Kenmore 796.80272900, 796.81073310, 79661552610, 79661553610, 79671552610, 79671553610, 79681392610, 79681393610, 79691392610, 79691393610 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM length, width, and rib pattern 🌀 Restores Drum Rotation – Ensures smooth, consistent dryer operation 🔇 Reduces Noise & Slippage – Helps eliminate squealing or drum stoppage 💪 Heavy-Duty Rubber Construction – Designed for long service life 💰 Cost-Effective Repair – Reliable alternative to OEM dryer belts 📐 Product Specification ✅ Brand and Models Compatibility: Fits select LG and Kenmore dryer models. 🔥 Specifications: 4-rib, 3-groove poly-V belt, black rubber, ~92"L x 1/4"W x 1/16"H, designed for durability and precise fit. 💰 Cost-Effective Alternative: Replacement belt offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a putty knife, Phillips screwdriver, flat-blade screwdriver, work gloves, optional second person; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves drum not tumbling, loud noises, or extended drying times. Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation. 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Basic Steps: Disconnect dryer power. Open the dryer cabinet and remove the drum. Remove the worn or broken belt. Install the new XPARTCO 4400EL2001F belt around the drum and motor pulley. Reinstall the drum and reassemble the dryer. Restore power and run a test cycle. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, reliable dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

🚪 EXP571 Dryer Door Catch This Dryer Door Catch is a replacement part for specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number Exp571. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. ✅ Key Features: High-quality aftermarket replacement Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: WP71002106, WP3389441, 3389441, 71002106, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AP2042209, PS266896, 131658800, AP2107362, PS418433, 5307521419, 10690002, 10690001. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Whirlpool✔️ Maytag✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic ? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the EXP71 dryer door catch from parts-o-matic.com, and enjoy fast, free U.S. shipping!

Read more less

XPARTCO 279640 Dryer Idler Pulley The XPARTCO 279640 is an aftermarket replacement dryer idler pulley (also called a belt tension pulley wheel) compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral. The idler pulley is spring-tensioned against the drive belt to maintain correct tension as the belt wraps around the drum — allowing the drum to rotate smoothly and quietly. When the idler pulley bearing wears out, the belt loses proper tension and the dryer begins making squealing, squeaking, or clunking noises, and the drum may eventually stop spinning. This pulley is constructed from sturdy plastic with a metal bearing and measures 1-7/8" L x 3/4" W x 1-7/8" H. The kit includes the greased pulley wheel, washer, and tri-ring retaining clip — everything needed for a complete replacement. It mounts directly to the existing idler arm on compatible models. Note: this is the pulley wheel only, not the full idler arm assembly. On some newer Whirlpool models, the complete W10837240 idler pulley arm assembly may be required instead. Quick Answer The XPARTCO 279640 Dryer Idler Pulley fixes Whirlpool-family dryers that are squealing, squeaking, clunking, or have a drum that won't spin due to improper belt tension. Plastic body with metal bearing. 1-7/8" L x 3/4" W x 1-7/8" H. Kit includes pulley, washer, and tri-ring clip. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers. Pulley only — not the full arm assembly. Common Problems This Part Fixes Loud squealing or squeaking noise when dryer is running Clunking or thumping sound during the drying cycle Dryer drum not spinning — belt slips or loses tension when pulley bearing fails Belt repeatedly slipping off due to improper tension Dryer drum spinning intermittently and stopping while the motor continues to run Excessive vibration or shaking during the drying cycle Visible wear, cracking, flat spots, or a pulley wheel that no longer spins freely on its shaft Replaces Part Numbers This idler pulley directly replaces the following OEM and cross-reference part numbers: 279640, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, AWP39098, PD00002356, EAP334244, AP3094197, PS334244. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Crosley dryers Inglis dryers Admiral dryers Important: The 279640 is a pulley wheel only — it mounts to the existing idler arm on compatible models. Some newer Whirlpool-family dryers (particularly models with the lint screen inside the door) require the complete W10837240 idler pulley arm and bracket assembly instead. If your model calls for W10837240, order that part rather than the 279640 pulley alone. Key Features Maintains correct tension on the drive belt for smooth, quiet drum rotation every cycle Plastic body with metal bearing — durable construction resists wear and heat damage Dimensions: 1-7/8" L x 3/4" W x 1-7/8" H — direct replacement for the original 279640 Kit includes greased pulley wheel, washer, and tri-ring retaining clip — ready to install Pulley comes pre-greased — no additional lubrication required Mounts directly to existing idler arm on compatible Whirlpool-family models Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers Aftermarket replacement built to OEM-equivalent quality standards Often replaced together with the drum belt (341241 or 661570V) for a complete drum drive repair DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 279640 Part Type Dryer Idler Pulley Wheel (Belt Tension Pulley) Condition Aftermarket Replacement Application Gas and Electric Dryers Dimensions 1-7/8" L x 3/4" W x 1-7/8" H Material Plastic body / Metal bearing Color White Lubrication no additional lubrication required Includes Pulley wheel, washer, and tri-ring retaining clip Note Pulley wheel only — not the full arm assembly (see W10837240 for arm assembly) Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, Admiral Often Replaced With 341241 or 661570V Drum Belt Installation Notes ⚠️ Unplug Dryer Before Starting Unplug the dryer from the power outlet (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension from the idler pulley, then lift the drum and slide the belt off. Remove the tri-ring retaining clip from the idler arm shaft using needle-nose pliers, then slide the old pulley wheel off the shaft. Slide the new 279640 pulley wheel onto the idler arm shaft, reinstall the washer, and press the new tri-ring clip onto the shaft to secure the pulley. Re-route the drum belt around the new pulley and motor pulley, reinstall the drum, and reassemble the dryer. Run a test cycle to verify quiet operation. Tip: While the dryer is open, inspect the drum belt for wear and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, small flat-head screwdriver, needle-nose pliers. Frequently Asked Questions What is the difference between the 279640 pulley and the W10837240 idler assembly? The 279640 is just the pulley wheel — it replaces only the wheel on the existing idler arm and is used on older Whirlpool-family dryer models. The W10837240 is a complete idler arm and bracket assembly used on newer Whirlpool-family models (particularly those with the lint screen inside the door). If your dryer originally used the 279640, order this part. If your parts diagram calls for W10837240, order that assembly instead — the 279640 pulley alone will not fit the newer arm design. What does the idler pulley do? The idler pulley is a spring-tensioned wheel mounted on the idler arm inside the dryer. It presses against the drive belt to keep the correct amount of tension on the belt as it wraps around the drum. Without proper tension, the belt slips, the drum spins unevenly, or the drum stops spinning entirely. A worn pulley bearing also causes squealing, squeaking, or clunking noises during operation. Should I replace the drum belt at the same time? Yes — since the dryer is already disassembled, this is the ideal time to inspect and replace the drum belt (341241 or 661570V depending on your model). The belt and idler pulley wear at similar rates, and a worn belt on a new pulley significantly shortens the life of the new part. Replacing both together in a single repair also saves you from having to disassemble the dryer again shortly after. Why is my dryer squealing? A high-pitched squeal when the dryer starts or runs is one of the most common signs of a worn idler pulley bearing. As the bearing wears, it creates friction and noise against the shaft. The squeal typically gets louder over time and may eventually turn into a grinding or clunking sound as the bearing fails further. Replacing the idler pulley is usually the fix in these cases, and is much less expensive than a service call. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic with a metal bearing to match the dimensions and performance of the original 279640 idler pulley. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 661570 Dryer Drum Belt Replaces 661570V The XPARTCO 661570 is an aftermarket replacement dryer drum belt compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. The drum belt wraps around the outside of the dryer drum, loops around the idler pulley and motor pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber, this 4-rib belt measures 93-1/2 inches long x 1/4 inch wide x 1/8 inch high with 4 ribs and 3 grooves. It is a direct drop-in replacement for OEM part numbers 661570V and 661570, and is part of the 4392067 dryer repair kit. It pairs with the W10837240 idler pulley and WPW10314173 drum rollers for a complete drum drive overhaul. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 661570 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is present during operation. Compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. Measures 93-1/2" L x 1/4" W x 1/8" H with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 661570V, 661570, 3387610, 3389728, 3393999, 339728, 4248258, 661570VP, AWP761693, OEM17951196, PD00023608, FIX382430, AP5983729, PS11722115. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Maytag dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Amana dryers KitchenAid dryers Crosley dryers Admiral dryers Speed Queen dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the idler pulley and motor pulley for smooth, consistent tumbling every cycle 93-1/2" length x 1/4" width x 1/8" height — 4-rib, 3-groove design for a secure, slip-free grip on the pulleys Made from high-strength rubber — resists cracking, stretching, heat damage, and oil Direct replacement for OEM part numbers 661570V and 661570 — no modification required Part of the 4392067 dryer repair kit — pairs with W10837240 idler pulley and WPW10314173 drum rollers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 661570 OEM Part Number 661570V Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 93-1/2 inches Width 1/4 inch Height 1/8 inch Ribs 4 ribs, 3 grooves Material High-strength rubber Color Black Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, Speed Queen Part of Kit 4392067 Dryer Repair Kit Often Replaced With W10837240 Idler Pulley, WPW10314173 Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release the belt from the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 661570 belt around the drum with the ribbed side facing inward toward the drum. Route the belt around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (W10837240) and drum rollers (WPW10314173) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What is the difference between 661570 and 661570V? These are the same belt. 661570V is the updated OEM part number (the "V" denotes the current version) that superseded the original 661570. Both numbers refer to the identical drum belt — this aftermarket replacement is compatible with both. How does the 661570 differ from the 341241 and W10205415 belts? All three are Whirlpool-family dryer drum belts, but they differ in length, width, and rib count. The 661570 is 93-1/2" long x 1/4" wide with 4 ribs and 3 grooves. The 341241 is 92-1/4" long x 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 92" long x 3/8" wide with 5 ribs and 4 grooves. They are not interchangeable — always use the part number specific to your dryer model. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound, a burning rubber smell, or damp clothes after a full drying cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched out of shape. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (W10837240) and drum support rollers (WPW10314173) at the same time. All three parts wear together and are sold together in the 4392067 dryer repair kit. Replacing all three prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 661570V belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse The WP3392519 is a genuine Whirlpool OEM thermal fuse mounted on the blower housing next to the blower fan. This fuse is a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to the dryer. That's why a blown thermal fuse produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. This fuse opens at approximately 196°F (91°C) and terminates in two 3/16" wire terminals for a direct plug-in fit. Unlike a resettable thermostat, this thermal fuse cannot be reset once it blows — it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what the fuse is designed to react to. A shorted heating element or a failed regulating thermostat can also cause the dryer to run hot enough to blow the fuse. It directly replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005. Quick Answer The WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse fixes Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers that won't start at all — no lights, no tumble, no response to any button. Opens at approximately 196°F (91°C). Two 3/16" wire terminals. Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, 80005. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after running unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Dryer that recently smelled like burning or overheating before failing Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED, WGD series Maytag electric and gas dryers — MEDC, MGDC series (select Whirlpool-built models) Kenmore dryers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana dryers (select models) Roper, Estate, Inglis, and Crosley dryers (select models) Verified model numbers include: MEDC465HW0, MGDC465HW0, WED4850HW0, WED4950HW0, WED49STBW1, WET4024HW0, WET4124HW0, WGD4850HW0, WGD4950HW0, YMEDC465HW0, YWED4850HW0, and YWET4024HW0. Note: This fuse also fits select commercial and stacked washer/dryer combination units on the Whirlpool platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening temperature and terminal configuration One-time safety device that cuts power if the dryer overheats Opens at approximately 196°F (91°C) Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse Two 3/16" wire terminal connectors for a direct plug-in electrical fit Mounts to the blower housing next to the blower fan Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005 Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP3392519 Part Type Dryer Thermal Fuse (Thermal Cut-Off) Condition Genuine OEM Brand Whirlpool Opening Temperature Approx. 196°F (91°C) Location Blower housing, next to the blower fan Terminals 2 (3/16" wire terminals) Resettable No — one-time use, must be replaced once blown Dimensions Approx. 2" x 1/2" Repair Difficulty Medium — basic disassembly required Quantity 1 thermal fuse Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, Amana, Estate, Inglis, Crosley Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted. Photograph the wiring before disconnecting the wire terminals from the old fuse. Remove the mounting screw holding the fuse in place and pull it free, disconnecting both wire terminals. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new WP3392519 in the same mounting position, reconnect both wire terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer has no power at all and the lights won't turn on. Is this the thermal fuse? It's a strong possibility. When this thermal fuse blows, it cuts power broadly enough that the console lights and control panel can go completely dark, not just the heating function — that's a normal result of how this fuse is wired into the circuit. Before replacing it, confirm the outlet has power and the breaker hasn't tripped, then check the fuse for continuity with a multimeter. If it shows no continuity, this fuse is the correct fix, though it's also worth checking the exhaust ducting since that's the most common underlying cause. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the heating element and cycling thermostat checked as well, since a component stuck in the "on" position can also drive excess heat. Can I just reset the thermal fuse instead of replacing it? No. Unlike a cycling thermostat, this thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. My clothes came out extremely hot right before the dryer died. Is that related? Yes, this is a classic warning sign. Clothes coming out unusually hot indicates the dryer was already running hotter than normal, which is exactly the condition that leads to a blown thermal fuse. If you noticed this before the dryer stopped working, it strongly points to a ventilation or airflow problem that should be fully addressed before running the dryer again. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening temperature, terminal configuration, and mounting position of the thermal fuse originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4561EL3002A Dryer Idler Pulley Assembly The XPARTCO 4561EL3002A is an aftermarket replacement dryer idler pulley assembly compatible with select LG and Kenmore electric and gas dryers. The idler pulley assembly is a spring-tensioned arm, pulley wheel, and spring kit that presses against the drive belt to keep it under constant tension as it wraps around the drum and motor pulley. Without correct belt tension, the belt slips, the drum stops spinning, and the dryer tumbles clothes poorly or not at all. A worn idler pulley bearing is also one of the most common causes of squealing, squeaking, and thumping noises in LG dryers. This complete assembly includes the idler arm, pulley wheel, and idler spring. Overall dimensions are 5-3/4"L x 2-1/4"W x 3-7/8"H with a 2-1/4" diameter pulley wheel. Constructed from plastic and metal in white, black, and gray. It directly replaces 4561EL3002B, DE3002A, 4980EL3004, 1267530, AP4438243, AH3523033, EA3523033, EAP3523033, PD00001729, and PS3523033. Note: the pulley wheel only (without arm and spring) is sold separately as APN4560EL3001A — this listing is for the complete idler assembly. Often replaced together with the drum belt (4400EL2001A) and drum rollers (4581EL2002A) for a complete drum drive repair. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 4561EL3002A Dryer Idler Pulley Assembly fixes LG and Kenmore dryers that are squealing, thumping, or where the drum has stopped spinning because belt tension is lost. Complete assembly — idler arm, pulley wheel, and spring included. 5-3/4"L x 2-1/4"W x 3-7/8"H overall; 2-1/4" pulley diameter. Replaces 4561EL3002B, DE3002A, 4980EL3004, 1267530, AP4438243, AH3523033, EAP3523033, PS3523033. Often replaced with drum belt (4400EL2001A) and drum rollers (4581EL2002A). Common Problems This Part Fixes Drum not spinning — belt has lost tension and slipped off Loud squealing or squeaking noise during the drying cycle — worn idler pulley bearing Thumping or clunking noise as the pulley wheel wobbles on a worn axle Belt repeatedly falling off after reinstallation — idler no longer maintaining tension Grinding noise from the idler area — bearing completely failed Drum spinning intermittently due to inconsistent belt tension Idler arm visibly cracked or pulley wheel no longer spinning freely by hand Replaces Part Numbers This idler pulley assembly directly replaces the following OEM and cross-reference part numbers: 4561EL3002A, 1267530, 4561EL3002B, ALG51226, AH3523033, AP4438243, EA3523033, EAP3523033, PD00001729, PS3523033 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley assembly is compatible with select LG and Kenmore gas and electric dryers: LG electric dryers — DLE series (DLE0442W, DLE1001W, DLE2250W, DLE2350W, DLE3133W, DLE3777W, DLE4801W, DLE5001W, DLE5955W, DLE7177WM and related models) LG electric dryers — DLEX series (DLEX3885W, DLEX5780VE and related models) LG gas dryers — DLG series (DLG0452W, DLG2251W, DLG2351W, DLG3744W, DLG3788W, DLG5002W, DLG5966W and related models) LG gas dryers — DLGX series (DLGX3886W and related models) Kenmore / Sears dryers — 796-series (LG-built electric and gas models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete idler pulley assembly — includes idler arm, pulley wheel, and idler spring Maintains correct drive belt tension so the drum spins smoothly and quietly during every drying cycle Overall dimensions: 5-3/4"L x 2-1/4"W x 3-7/8"H; pulley wheel diameter: 2-1/4" Plastic arm and housing with metal pulley shaft — durable construction for continuous operation Replaces 4561EL3002B, DE3002A, 4980EL3004, AP4438243, AH3523033, EAP3523033, and PS3523033 Note: pulley wheel only (without arm and spring) is sold separately as APN4560EL3001A — this listing is the complete assembly Often replaced together with drum belt (4400EL2001A) and drum rollers (4581EL2002A) Compatible with LG DLE, DLEX, DLG, DLGX series and Kenmore 796-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP4561EL3002A Also Replaces 4561EL3002B (prior revision) Part Type Dryer Idler Pulley Assembly (Arm, Wheel, and Spring) Condition Aftermarket Replacement Application LG and Kenmore Gas and Electric Dryers Overall Dimensions 5-3/4"L x 2-1/4"W x 3-7/8"H Pulley Wheel Diameter 2-1/4 inches Material Plastic / Metal Color White / Black / Gray Includes Idler arm, pulley wheel, and idler spring — complete assembly Pulley Wheel Only APN4560EL3001A (sold separately — not this listing) Often Replaced With 4400EL2001A Drum Belt, 4581EL2002A Drum Rollers Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power (and shut off gas for gas dryers) before beginning. Wear work gloves — there are sharp sheet metal edges inside the LG dryer cabinet. Access the idler pulley by removing the back panel of the dryer (on most LG models) or the front panel and top panel. Take a photo of the belt routing around the drum, motor pulley, and idler pulley before removing anything — this is essential for correct reassembly. Release belt tension by pressing the idler arm toward the motor and sliding the belt free. Remove the idler spring from its anchor point, then unclip or unscrew the idler arm from its mounting bracket. Install the new 4561EL3002A idler assembly in the same position — hook the spring onto its anchor point first, then mount the arm. Re-route the belt around the drum (ribbed side in), under the idler pulley, and around the motor pulley, then allow the idler arm to tension the belt. Reassemble panels, restore power, and run a test cycle. Tip: while the dryer is open, inspect and replace the drum belt (4400EL2001A) and drum rollers (4581EL2002A) if worn. Tools needed: Phillips screwdriver, Torx screwdriver (T20 on some models), needle-nose pliers, work gloves. Frequently Asked Questions What does the dryer idler pulley do? The idler pulley is a spring-loaded arm and wheel assembly that presses against the drive belt between the drum and the motor pulley, keeping the belt under constant tension. This tension is what allows the belt to grip both the drum surface and the motor pulley so the motor's rotation is transmitted to spin the drum. Without proper tension — or with a pulley bearing that has seized or worn out — the belt slips, the drum stops spinning, and the dryer produces heat without tumbling clothes. A worn bearing also creates the high-pitched squealing noise that is the most recognizable symptom of idler pulley failure on LG dryers. What is the difference between 4561EL3002A and 4561EL3002B? These are the same LG dryer idler pulley assembly across two production revisions. The 4561EL3002B was an earlier version and the 4561EL3002A is the current part number. Both are the same functional assembly — if your dryer's parts diagram shows 4561EL3002B, the 4561EL3002A is the correct current replacement and is covered by this listing. Should I also replace the drum belt and rollers at the same time? Yes — since the dryer must be disassembled to replace the idler pulley, this is the ideal time to also inspect and replace the drum belt (4400EL2001A) and drum support rollers (4581EL2002A). All three parts form the drum drive system and wear at similar rates. A worn roller or belt is often what caused the idler pulley to wear prematurely. Replacing all three in one repair eliminates the most common drum drive failure points and prevents a repeat teardown in the near future. Can I just replace the pulley wheel without the arm and spring? Yes — the pulley wheel alone (without the arm and spring) is sold separately as part number APN4560EL3001A. If only the wheel bearing has failed and the arm and spring are in good condition, you can order just the wheel. However, if the arm is cracked, the spring has lost tension, or both the wheel and arm have significant wear, ordering the complete 4561EL3002A assembly is more cost-effective and ensures the entire idler system is renewed in a single repair. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from plastic and metal to match the dimensions and performance of the original 4561EL3002A idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less