W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly
The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises.
This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump).
Quick Answer
The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ.
Common Problems This Part Fixes
Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms
Weak water pressure at the spray arms — impeller worn or motor failing
Loud droning noise that gets louder over time — worn motor bearings
Grinding or unusual noise during operation
Water retention/pooling in the bottom of the tub
Leaks from the pump housing — seal breakdown
Motor humming but spray arms barely turning
Reduced cleaning performance overall
Motor not running at all — failed pump motor windings
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers:
W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783
W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This circulation pump motor assembly is compatible with select dishwashers from the following brands:
Whirlpool dishwashers — select models (verify with your parts diagram)
KitchenAid dishwashers — select models
Maytag dishwashers — select models
Jenn-Air dishwashers — select models
Amana dishwashers — select models
Magic Chef dishwashers — select models
Admiral dishwashers — select models
Norge dishwashers — select models
Roper dishwashers — select models
Kenmore / Sears dishwashers — select Whirlpool-built models
Ikea dishwashers — select Whirlpool-built models
This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing
Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure
Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns
Current OEM production part — directly supersedes W11122133
Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317
Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine
Drain pump is not included — your existing drain pump transfers to the new assembly
Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers
DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
W11414076
Supersedes
W11122133
Part Type
Dishwasher Circulation Pump & Motor Assembly
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Function
Delivers water to the spray arms for washing and rinsing
Motor Attachment
Separates from pump case with 3 Torx screws
Drain Pump
Not included — transfer your existing drain pump
Location
Bottom of dishwasher (access by laying unit on its back)
Compatible Brands
Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves.
Frequently Asked Questions
The motor runs but water barely reaches the spray arms — do I definitely need a new pump?
Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try.
My dishwasher motor is loud and getting louder — is that the pump?
Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing.
Does this come with the drain pump?
No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub.
What's the difference between W11414076 and W11122133?
These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 4970FR2084Z Washer Suspension Spring
The XPARTCO 4970FR2084Z is an aftermarket replacement suspension hinge spring for LG and Kenmore front-load washers. The suspension springs support and stabilize the outer tub during wash and spin cycles and help it stay steady through unbalanced loads. When a spring is broken, snapped, or stretched, the washer may make a loud noise during spin, vibrate heavily, or stop spinning.
This is a direct-fit aftermarket replacement for the original LG spring. A broken spring can let the drum drop and damage the shocks, dampers, and door seal, so inspect those parts while the washer is open.
Quick Answer
The XPARTCO 4970FR2084Z Suspension Spring fixes an LG or Kenmore front-load washer that is loud or shakes badly during spin, stops spinning, or has a drum that has dropped because a suspension spring is broken or stretched. Classic symptom: a loud banging or grinding noise on spin, as if something snapped inside the washer.
Common Problems This Part Fixes
Loud drum noise during the spin cycle
Excessive vibration or shaking on spin
Washer stops spinning or stops mid-cycle
Drum looks lowered, or the front door seal is pushed forward
Visibly broken, snapped, or stretched spring
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This suspension spring directly replaces the following part numbers:
4970FR2084Z, MHY62964802, AGF75223050, MHY57694605, MHY62964801, ALG51959, AP4998892, AH3524578, EA3524578, OEM14996685, PD00028343, PS3524578
These numbers span several generations of LG's own part numbering for this spring as washer models were updated. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number.
Compatibility
This suspension spring is listed for LG and Kenmore front-load washers, including these examples:
LG WM3470HWA, WM3360HWCA, WM3700HVA, WM3770HVA, WM4370HWA, WM5000HWA
LG WM2601HW, WM2801HWA, WM2901HVA, WM3001HWA, WM3875HWCA
Kenmore 79641172212, 79641182311
Note: The models above are a sample of more than 100 listed models, not a full list. Washers use more than one suspension spring, and customers often replace the springs on both sides together, so check how many your model uses. Confirm your model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Direct-fit aftermarket suspension hinge spring for LG and Kenmore front-load washers
Supports and stabilizes the outer tub during wash and spin cycles
Resolves loud spin noise and vibration caused by a broken or stretched spring
Fits a long list of LG and Kenmore front-load models
Product Specifications
Part Number
XP4970FR2084Z
OEM Part Number
4970FR2084Z
Part Type
Washer Suspension Hinge Spring
Condition
Aftermarket Replacement
Application
LG & Kenmore Front-Load Washers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the washer and turn off the water supply before beginning, and wear work gloves. Follow your model's service guide to reach the springs, which usually means removing the top and front panels. The drum is heavy, so have a second person lift it, or use a rope loop, while you hook the new spring, which customers say is the hardest step. Check the shocks, dampers, hoses, and door seal while you are in there, since a dropped drum can damage them. Reassemble, then run a spin cycle and check the washer is steady.
Frequently Asked Questions
My washer is very loud on spin. Is this the part I need?
A broken or stretched suspension spring is a common cause of loud spin noise and heavy vibration, especially if it sounded like something snapped. Check the springs, shocks, and dampers for damage.
Should I replace all the springs?
Many customers replace the springs on both sides together, since an old spring may stretch or fail soon after. Check your parts diagram for how many your model uses.
Is this an easy repair?
Retailers rate it easy to moderate, with customers reporting from under 15 minutes to 2 hours. Hooking the new spring while holding up the drum is the hardest part, so a helper makes it easier.
Will this fit my washer?
It is listed for many LG and Kenmore front-load washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10542314 Dishwasher Gasket (Without Door Strike)
Fits Specific Whirlpool, Kenmore, Maytag Dishwasher models.
Door Gasket Only (Strike is not included)
Description: This dishwasher gasket and strike kit (W10542314) is designed for a secure and leak-proof seal on your dishwasher. It ensures a tight closure and proper functioning for your appliance. Trust in XPARTCO for expert solutions and reliable performance with your dishwasher.
Replaces Part Numbers:W10542314, 2409202, 8268888, W10284090, W10300589, W10350162, W10542314VP, AP5650274, PS5136129.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W11220230 Washer Water Inlet Valve
The XPARTCO W11220230 is an aftermarket replacement washer water inlet valve designed to control the flow of hot and cold water into your washing machine during each cycle. This Water Inlet Valve is a replacement part compatible with specific Maytag, Whirlpool washing machine models. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance..
Over time, inlet valves can fail due to mineral buildup, electrical issues, or worn internal seals — leading to slow filling, no fill, or continuous water flow. Replacing the valve restores proper water control and helps prevent leaks or cycle errors.
Quick Answer
The XPARTCO W11220230 Washer Water Valve fixes washers that won’t fill, fill too slowly, or won’t stop filling with water. It controls incoming water flow and restores proper wash cycle operation.
Common Problems This Part Fixes
Washer not filling with water
Slow water fill during cycles
Water continuously flowing into washer
Incorrect water temperature
Washer stopping due to fill errors
Leaking or stuck inlet valve
Replaces Part Numbers
This water inlet valve replaces the following part numbers:
W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, AWP43504, EAP12349461, PD00042661, AP6329544, PS12349461
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water valve is compatible with select washers from the following brands:
Whirlpool washers
Maytag washers
Amana washers
Kenmore / Sears washers (select models)
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
Key Features
Three coil hot and cold water valve.
OEM-equivalent fit, performance, and durability
Restores proper water fill levels and cycle operation
Durable construction resists mineral buildup and wear
Prevents leaks and overfilling issues
Direct replacement for W11220230 valve assembly
Product Specifications
Part Number
W11220230
Part Type
three coil hot and cold water inlet valve.
Application
Top Load / Front Load Washers
Condition
Aftermarket Replacement
Function
Controls Water Flow
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore
Installation Notes
⚠️ Safety First — Disconnect Power & Water Supply Unplug the washer and turn off the water supply before servicing. Remove the rear or top panel to access the inlet valve. Disconnect water hoses and electrical connectors, then remove the mounting screws to replace the valve. Reconnect hoses securely to avoid leaks and test for proper operation after installation.
Frequently Asked Questions
What does a washer water inlet valve do?
It controls the flow of hot and cold water into the washer. When the valve fails, the washer may not fill properly or may overfill.
Will this fix a washer that won’t fill?
Yes, a faulty inlet valve is one of the most common causes of no-fill or slow-fill issues.
Is this an OEM part?
This is a high-quality aftermarket replacement built to OEM-equivalent standards for performance and durability.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility.
✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10730972 Washer Drain Pump Replaces WPW10730972
The XPARTCO W10730972 is an aftermarket replacement front-load washer drain pump and motor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, Inglis, and KitchenAid front-load washers — including the Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus. The drain pump removes water from the washer tub during the drain and spin phases of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, display error codes F21, F33, or SD, or leak from the pump area.
This complete assembly includes the motor, pump housing, and integrated filter — these components are only available as a complete assembly and are not sold separately. Rated 120V, 60Hz, 78W, 1.2A (CL.F duty class). Assembly dimensions are 8-3/4"L x 7"W x 5-1/4"H in off-white plastic housing. Note: Whirlpool redesigned this pump — the replacement may look different from the original but fits and functions identically. It directly replaces WPW10730972, W10130913, W10130913-B, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, AP6023956, PS11757304, and additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10730972 Washer Drain Pump fixes Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus front-load washers that won't drain, leave standing water, or display error codes F21, F33, or SD. Complete assembly — motor, pump housing, and filter included. 120V/60Hz/78W/1.2A. 8-3/4"L x 7"W x 5-1/4"H. Note: redesigned — may look different from original but fits identically. Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, PS11757304.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error code F21 displayed — long drain fault (washer unable to drain in allotted time)
Error code F33 displayed — pump motor fault
Error code SD displayed — suds detection or drain issue
Washer stopping mid-cycle due to a drain fault
Loud humming or grinding noise during the drain phase
Water leaking from the front lower area of the washer — pump seal failure
Pump motor running but water not being expelled from the tub
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WPW10730972, W10730972, W10130913, 4281917, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, WPW10730972VP, AP6023956, AWP50633, B40-3A01, EAP11757304, PD00025949, PS11757304
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select front-load washers from the following brands and series:
Whirlpool front-load washers — Duet series (WFW8300, WFW8400, WFW9050, WFW9150, WFW9200, WFW9250, WFW9400, WFW9450, WFW9500, WFW9550, WFW9600, WFW96HEA, WFW97HED, WFW98HEB and related models)
Maytag front-load washers — 2000 series (MHW2000AW, MHW2000BWW and related models)
Maytag front-load washers — 3000 series (MHW3000BW and related models)
Maytag front-load washers — 4000 series (MHW4000BW, MHW4200BW, MHW5100DW, MHW6000AW, MHW6000XW and related models)
Kenmore / Sears front-load washers — HE2 and HE2T Plus series (110.45862400, 110.47532602 and related models)
Amana front-load washers (select models)
Inglis front-load washers (select models)
KitchenAid front-load washers (select models)
Note: Whirlpool redesigned this pump assembly — the replacement may look different from your original pump (larger in size on some versions) but is engineered to fit and function identically in all compatible models. Always verify your model number before ordering. Before replacing the pump, check and clear the coin trap/drain filter — a clogged filter is a common cause of F21/F33 errors that does not require pump replacement.
Key Features
Removes water from the tub during drain and spin cycles — essential for proper washer operation
Complete assembly — motor, pump housing, and integrated filter included; components are not sold separately
Rated 120V, 60Hz, 78W, 1.2A (CL.F) — correct electrical specifications for compatible Whirlpool-family front-load washers
Dimensions: 8-3/4"L x 7"W x 5-1/4"H — off-white plastic housing
Resolves error codes F21 (long drain), F33 (pump motor fault), and SD (suds/drain) on compatible models
Redesigned assembly — may look different from original but fits and functions identically
Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, and over 20 additional cross-references
Compatible with Whirlpool Duet, Maytag 2000/3000/4000 series, Kenmore HE2/HE2T Plus, Amana, Inglis, and KitchenAid
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPW10730972
OEM Part Number
WPW10730972
Part Type
Front-Load Washer Drain Pump and Motor Assembly
Condition
Aftermarket Replacement
Application
Front-Load Washers (Duet, Maytag 2000/3000/4000, Kenmore HE2/HE2T Plus)
Voltage
120V AC
Frequency
60 Hz
Wattage
78W
Amperage
1.2A
Duty Class
CL.F
Dimensions
8-3/4"L x 7"W x 5-1/4"H
Color
Off-White
Material
Plastic housing
Includes
Motor, pump housing, and integrated filter — complete assembly
Design Note
Redesigned — may look different from original; fits identically
Error Codes Resolved
F21 (long drain), F33 (pump motor fault), SD (suds/drain)
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, Inglis, KitchenAid
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Place towels on the floor — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel of the washer. Remove the screws on the lower kick panel or snap panel to expose the pump access area. Before removing the pump, drain residual water by removing the coin trap/filter cap from the filter housing (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the drain hose clamps and disconnect the hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Transfer the hoses and wiring to the new W10730972 pump, secure the mounting hardware, and reinstall the front panel. Restore power and water, run a drain/spin cycle, and check for leaks. Tools needed: Phillips screwdriver, Torx screwdriver (T20 on some models), pliers, shallow pan, towels, work gloves.
Frequently Asked Questions
What do error codes F21, F33, and SD mean on Whirlpool Duet and Maytag washers?
F21 indicates a long drain fault — the washer was unable to drain within the expected time (typically 8 minutes). F33 indicates a pump motor fault — the control board is not detecting the pump motor operating correctly. SD is a suds detection code that can also appear when drain issues prevent the suds from clearing properly. All three codes point toward the drain pump or a drain obstruction. Before replacing the pump, check and clean the coin trap filter — a clogged filter is one of the most common causes of F21 errors and clearing it often resolves the code without needing a new pump.
Should I check the coin trap filter before replacing the pump?
Yes — always check the coin trap filter before replacing the pump. On Whirlpool Duet and Maytag front-load washers, the coin trap filter is located inside the lower front access panel, typically behind a small cap or cover. Removing the cap and clearing lint, coins, and debris from the filter restores drain flow and clears F21/F33 errors in many cases without any part replacement needed. If the filter is clear and the pump still humbles or fails to drain, the pump needs replacement.
Why does the replacement pump look different from the original?
Whirlpool redesigned this drain pump assembly during its production lifecycle — the WPW10730972 replacement is physically larger than some of the older 8540024-series pumps it supersedes. Despite looking different, the redesigned pump uses the same hose and electrical connection points and is a direct fit in all compatible models. The larger housing is an intentional design improvement to increase pumping capacity. If the pump looks bigger than what you removed, this is normal and expected — install it in the same way as the original.
What is the difference between W10730972 and WPW10730972?
These are the same drain pump assembly. WPW10730972 is the updated Whirlpool OEM part number that superseded the original W10730972. The W10130913 and 8540024 are also cross-references for earlier versions of this same pump. This aftermarket replacement is compatible with all of these numbers.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and performance of the original WPW10730972 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
4 Pack - XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703
The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement.
Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more.
Common Problems This Part Fixes
Violent shaking or vibrating during the spin cycle
Loud banging, thumping, or clunking noise during spin
Washer "walking" across the floor during the spin cycle
Outer tub hitting the sides of the cabinet during high-speed spin
Spin cycle errors caused by excessive tub movement triggering the imbalance sensor
Visible oil leak, broken mount, or collapsed shock absorber body
Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration
Replaces Part Numbers
This shock absorber directly replaces the following OEM and cross-reference part numbers:
WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This shock absorber is compatible with select front-load washers from the following brands and series:
Whirlpool front-load washers — GHW and WFW series
Maytag front-load washers — MHWE and MFW series
Kenmore / Sears front-load washers (select Whirlpool-built models)
KitchenAid front-load washers — KHWS series
Amana front-load washers
Jenn-Air front-load washers
Admiral front-load washers
Roper front-load washers
Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after.
Key Features
Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact
Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear
High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life
Direct replacement for WP8182703 and 8181646 — no modification required
Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers
Sold individually — most models require 4 shock absorbers; replace all 4 at the same time
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
8182703-4PK
OEM Part Number
WP8182703
Part Type
Front-Load Washer Shock Absorber (Hydraulic Dampener)
Condition
Aftermarket Replacement
Application
Front-Load Washers
Quantity Per Washer
4 (2 front, 2 rear)
Compatible Brands
Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper
Compatible Series
GHW, WFW, MHWE, MFW, KHWS
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves.
Frequently Asked Questions
What does the washer shock absorber do?
The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time.
How many shock absorbers does my front-load washer have?
Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one.
What is the difference between 8182703 and WP8182703?
These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers.
My washer still vibrates after replacing the shock absorbers — what else could it be?
If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
MJU62070602 Genuine LG OEM Refrigerator Water Line
Plastic tube, 5/16" - 79 inches in length
Replaces Part Number: MJU62070602, 5210JA3004R, 5210JA3004U, MJU62070606, 2676818, 5210JA3004B, 5210JA3029U, AH3536013, EA3536013, MJU62070601, MJU62070611, MJU62070615, AP4681126, PS3536013.
Water tubing MJU62070602 is an original equipment manufacturer (OEM) part that fits some Kenmore, Kenmore Elite and LG refrigerators. Water tubing MJU62070602 supplies water to refrigerator components that require water such as the ice maker and water dispenser. Replaces original refrigerator water tubing part numbers 5210JA3004U, 5210JA3029U, MJU62070601 and MJU62070606. Fits some Kenmore and Kenmore Elite 795-series refrigerators. Also fits some LG refrigerators in these series: LFD, LFX, LMX, LRFD, LRSC and LSC.
XPWE9X105 Dryer Front Lower Felt
Replaces Part Numbers:WE9X105, 277130, AH268338, AP2043044, EA268338, PS268338, WE09X0105
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO BPV-31 Refrigerator Refrigerant Piercing Valve / Line Tap Valve Kit
The XPARTCO BPV-31 is a universal bullet piercing tap valve (line tap valve) used to quickly access a sealed refrigerant line on refrigerators, freezers, window air conditioners, dehumidifiers, and other HVAC systems — without soldering or brazing. The valve clamps around a copper refrigerant line and, when the valve stem is tightened with the included hex key, a hardened piercing needle punctures the tubing to create an access port. This lets a technician connect a charging hose or gauge to check pressure, pull a vacuum, or add refrigerant to a system that has no factory service port. It's a staple tool for appliance service and DIY refrigerator/freezer repair.
Fits 1/4", 5/16", and 3/8" outside diameter copper pipes with the included adapters. The access port connection is a 1/4" male flare fitting. Rated to 500 PSI maximum, with a patented permanent gasket providing over 180 inch-lbs of sealing force — around 50 times the sealing area of a standard O-ring type valve — pressure tested at 250°F. Corrosion-resistant metal (zinc alloy) construction with a piercing needle engineered for concentricity and hardness to seat perfectly every time. Non-positional mounting requires no separate adapter valve and only 2" of clearance for installation. Each kit includes the piercing valve, a hex key wrench, and 2 adapters. It replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31.
Quick Answer
The XPARTCO BPV-31 Refrigerant Piercing Valve Kit taps into a sealed copper refrigerant line to add refrigerant, check pressure, or pull a vacuum — no soldering required. Fits 1/4", 5/16", and 3/8" OD pipes. 1/4" male flare port connection. 500 PSI max, patented gasket (50x the sealing area of an O-ring). Zinc alloy metal. Includes piercing valve, hex key, and 2 adapters; only needs 2" clearance. Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31. Not suitable for R410a systems.
Common Uses This Kit Serves
Adding refrigerant to a refrigerator or freezer that has no factory service port
Checking system pressure on a sealed refrigerant line for diagnostics
Pulling a vacuum on a system during service
Recharging window air conditioners and dehumidifiers
Confirming whether a sealed system has lost its refrigerant charge (leak diagnosis)
Providing temporary or service access to copper refrigerant tubing without brazing
Reviving a garage/shop refrigerator or freezer that has slowly lost its charge
Accessing R-12, R-22, R-134a, and other compatible refrigerant systems (NOT R410a)
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This bullet piercing tap valve directly replaces the following OEM and cross-reference part numbers:
BPV-31, BPV31, BPV31D, AP4502525, GPV14, GPV31, GPV38, GPV56, MPV31
The BPV-31 is a universal valve that covers the GPV-series (GPV14, GPV31, GPV38, GPV56) and MPV31 across the pipe sizes they individually served. Contact our support team if you need help confirming the correct valve for your line size.
Compatibility
This bullet piercing valve is a universal tool compatible with sealed refrigerant systems using copper tubing, including:
Refrigerators and freezers — all major brands with 1/4", 5/16", or 3/8" OD copper refrigerant lines
Window air conditioners — for recharging and pressure checks
Dehumidifiers — sealed refrigerant systems
Other HVAC systems with compatible copper line sizes
Refrigerant compatibility — works with R-12, R-22, R-134a and other common refrigerants
Important — NOT for R410a Systems: This BPV-31 piercing valve is NOT rated for R410a refrigerant systems, which operate at significantly higher pressures than the valve's design allows. Using it on an R410a system is unsafe. Before use, confirm your line's outside diameter (1/4", 5/16", or 3/8") and select the correct included adapter. Verify the pipe size before installation.
Key Features
Bullet piercing tap valve — taps a sealed copper refrigerant line to create an access port without soldering or brazing
Fits 1/4", 5/16", and 3/8" outside diameter copper pipes (with included adapters)
1/4" male flare access port connection for charging hoses and gauges
500 PSI maximum pressure rating
Patented permanent gasket — over 180 inch-lbs of sealing force, ~50 times the sealing area of a standard O-ring type valve; pressure tested at 250°F
Piercing needle engineered for concentricity and hardness to seat perfectly every time
Corrosion-resistant zinc alloy metal construction — won't rust or wear out over time
Non-positional mounting — no separate adapter valve required, installs in any orientation
Compact design needs only 2" of clearance for installation and use
Each kit includes: 1 piercing valve, 1 hex key wrench, 2 adapters
Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31
NOT suitable for R410a refrigerant systems
Product Specifications
Part Number
XPBPV-31
Part Type
Bullet Piercing Tap Valve (Line Tap Valve Kit)
Condition
Aftermarket Replacement
Application
Refrigerators, Freezers, Window AC, Dehumidifiers, HVAC (sealed copper lines)
Compatible Pipe Sizes
1/4", 5/16", 3/8" outside diameter
Port Connection
1/4" Male Flare
Maximum Pressure
500 PSI
Sealing Force
180+ inch-lbs (patented gasket, ~50x O-ring sealing area)
Pressure Tested
250°F
Material
Corrosion-resistant zinc alloy metal
Mounting
Non-positional, 2" clearance required
Kit Includes
1x Piercing Valve, 1x Hex Key, 2x Adapters
Not Compatible With
R410a refrigerant systems
Installation Notes
⚠️ Refrigerant Safety Warning Working with sealed refrigerant systems can expose you to pressurized refrigerant, which can cause frostbite, eye injury, and other harm. Wear safety glasses and protective gloves before piercing any line. Refrigerant handling may be regulated in your area — certain refrigerants require EPA certification (in the US) to purchase and handle. Never vent refrigerant to the atmosphere. This valve is NOT rated for R410a systems (too high pressure). If you're not experienced with refrigerant systems, have this work done by a qualified HVAC or appliance technician.
⚠️ Installation Steps — Clean the Line First Put on safety glasses and protective gloves. Identify the copper line you want to tap and confirm its outside diameter (1/4", 5/16", or 3/8") so you can select the correct included adapter. Clean the section of pipe where the valve will mount to prevent debris from entering the refrigerant line. Ensure the composite seal "O" ring/gasket is properly in place inside the valve. Place the two halves of the valve saddle around the pipe using the appropriate adapter insert for your pipe size. Install and evenly tighten the socket-head screws to clamp the valve body firmly around the pipe. To pierce the line, turn the valve stem clockwise with the included hex key until the needle punctures the tubing, then back the stem out (counterclockwise) to open the port and allow flow. To connect a gauge or charging hose: remove the cap, attach your hose to the 1/4" flare port, and open the valve by turning the stem counterclockwise. When finished, close the valve (turn the stem clockwise) BEFORE disconnecting the hose, then reinstall the protective cap. Note: the compact valve needs only 2" of clearance around the pipe. Tools needed: Included hex key wrench, safety glasses, protective gloves. (Note: to attach a gauge directly to the BPV, a retrofit valve adapter may be required — not included.)
Frequently Asked Questions
What is a bullet piercing valve used for?
A bullet piercing valve (line tap valve) lets you tap into a sealed copper refrigerant line to create an access port — without cutting, soldering, or brazing the line. Most household refrigerators and freezers are sealed systems with no factory service port, so if you need to check the refrigerant pressure, pull a vacuum, or add refrigerant, a piercing valve gives you that access quickly. It clamps around the pipe, and a needle pierces the tubing when you tighten the valve stem. It's commonly used in appliance repair and HVAC service, and by DIYers reviving a garage refrigerator or freezer that has lost its charge.
Which pipe sizes does this fit?
The BPV-31 fits 1/4", 5/16", and 3/8" outside diameter copper pipes using the included adapters. Before installing, measure or confirm your refrigerant line's outside diameter and select the matching adapter insert. Getting the size right is essential for a proper seal — an incorrectly sized adapter won't clamp tightly and can leak. If you're not sure of your line size, measure the outside diameter of the copper tubing with calipers or a pipe gauge.
Can I use this on an R410a system?
No — the BPV-31 is NOT rated for R410a refrigerant systems. R410a operates at significantly higher pressures than older refrigerants like R-12, R-22, and R-134a, and exceeds the safe working pressure of this valve (500 PSI max). Using it on an R410a system is unsafe and could result in valve failure or refrigerant release. This valve is appropriate for lower-pressure systems using R-12, R-22, R-134a, and similar refrigerants. For R410a systems, use service equipment specifically rated for R410a pressures.
Is a piercing valve a permanent solution?
Piercing valves are best thought of as a service-access tool rather than a permanent fixture. They work reliably for tapping into a line to diagnose, vacuum, or charge a system, and the BPV-31's patented gasket provides a much stronger seal than basic O-ring valves. However, for a long-term permanent service port, many technicians prefer to cut the line and braze in a proper Schrader service port. Some technicians have concerns about the very long-term sealing of any piercing valve left permanently on a line. If you leave the valve installed, make sure the stem is closed and the cap is in place, and check periodically for leaks.
Do I need EPA certification to add refrigerant?
In the United States, handling many refrigerants (and purchasing them) requires EPA Section 608 certification, and it is illegal to intentionally vent refrigerant to the atmosphere. Regulations vary by refrigerant type and jurisdiction. The piercing valve itself is a tool that anyone can install, but the refrigerant handling that follows may be regulated. If you're a DIYer, research the rules that apply to your specific refrigerant and location, or have the refrigerant work done by a certified technician. Always recover refrigerant properly rather than venting it.
Is this an OEM or aftermarket part?
This is an aftermarket universal service tool built to OEM-equivalent quality standards. The BPV-31 is a universal industry-standard bullet piercing valve design (also sold as Supco BPV31 and equivalent), manufactured from corrosion-resistant zinc alloy to match the fit, 1/4"/5/16"/3/8" pipe compatibility, 1/4" flare port, 500 PSI rating, and patented-style sealing gasket of the standard BPV-31 line tap valve. It replaces AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WR17X11653 Refrigerator Dispenser Ice Door Flapper
The XPARTCO WR17X11653 is an aftermarket replacement ice door flapper, also sold as the dispenser door assembly, ice chute door or door recess assembly, for GE, Hotpoint and Kenmore side-by-side refrigerators, replacing GE part WR17X11653. It sits in the ice chute opening, seals the freezer against warm room air, and opens when the dispenser lever is pressed so ice can reach your glass.
If the door is cracked, warped, or its gasket no longer seals, warm air gets into the chute and the dispenser suffers. Check your model number before ordering, as the kit may include more than one piece.
Quick Answer
The XPARTCO WR17X11653 Ice Door Flapper replaces the ice chute door on a compatible GE, Hotpoint or Kenmore refrigerator when it is cracked, warped, or no longer seals. Classic symptoms: door sweating, frost buildup at the chute, or ice not dispensing.
Common Problems This Part Fixes
Ice dispenser door sweating
Frost buildup around the ice chute
Ice not dispensing
Cracked, warped or damaged ice door
Worn rubber gasket leaking air into the freezer
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This ice door flapper directly replaces the following part numbers:
WR17X11653, WR17X3093, WR17X3492, AGE28222, AH964304, AP3672582, EA964304, EAP964304, PD00001157, PS964304
If your old part shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This ice door flapper is listed for GE, Hotpoint and Kenmore side-by-side refrigerators, including these examples:
GE TPH21PRSABB, TPH21PBSAWW, TFX20JRSBAD
GE DSE26JSEBCSS, DSF25KGTABG, DSF26DHWABB, CSK28DRBBAA
Kenmore 3639544313, 3639537713, 3639542623
Note: The models above are a small sample. One retailer lists this part for over 1,000 models. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Aftermarket replacement for the GE WR17X11653 ice door flapper
Seals the ice chute opening against warm room air
Opens when the dispenser lever is pressed to release ice
Replaces a cracked, warped or leaking ice door
Product Specifications
Part Number
XPWR17X11653
OEM Part Number
WR17X11653
Part Type
Refrigerator Dispenser Ice Door Flapper
Condition
Aftermarket Replacement
Application
Select GE, Hotpoint and Kenmore Side-by-Side Refrigerators
Installation Notes
⚠️ Unplug Power Before Installing Unplug the refrigerator and move perishable food to a cooler before you begin. Wear work gloves. A Phillips screwdriver and a small flat-blade screwdriver are typically needed. No installation instructions are included with the part, so keep your model's parts diagram handy and note how the old door and any springs or pieces come apart before removing them. Install the new door the same way, then restore power and test the dispenser.
Frequently Asked Questions
What does the ice door flapper do?
It seals the ice chute opening to keep warm room air out of the freezer, and it opens when you press the dispenser lever so ice can drop into your glass.
How do I know if my ice door needs replacing?
Look for a cracked or warped door, a damaged rubber gasket, door sweating, or frost buildup around the chute. Ice that won't dispense can also point to the door.
Is this an OEM or aftermarket part?
This is an aftermarket replacement from XPARTCO, made to replace GE part WR17X11653. If you specifically need a genuine GE part, contact our support team.
Will this fit my refrigerator?
It is listed for a large number of GE, Hotpoint and Kenmore side-by-side models, but the list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DA82-01415A Refrigerator Water Leak Service Kit
Water leak repair kit with updated internal duck bill.
Fits select Samsung refrigerator models.
Replaces Part Numbers: DA82-01415A, 3436781, AP5957964, PS10058968.
Description: This Water Leak Repair Kit is a replacement part for select Samsung refrigerator models, this field service kit used to address water leakage and excessive frost in bottom freezer or French door refrigerators with dual evaporators. The kit includes a drain probe, two drain tubes, and two silver foam strips. With these parts, you can prevent excessive frost buildup on the evaporator cover and fix issues like water leaks under the crisper or odd fan noises that stop when the doors are opened.
This is an aftermarket part that can be used as a replacement for the OEM part
XPARTCO W11688994 Washer Water Inlet Valve (Hot)
The XPARTCO W11688994 is an aftermarket replacement hot water inlet valve compatible with select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The hot water inlet valve is mounted at the back of the washer where the hot water supply hose connects. When the washer's control board calls for hot water during a wash cycle, the valve's internal solenoid opens, letting hot water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached.
When this valve fails, the washer may not fill with hot water at all, fill very slowly with hot water, fail to deliver hot or warm wash temperatures (even when selected), continuously drip water into the tub even when off, or display fill-related error codes. Construction is red and white plastic with a metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688994, W11036928, W11316255, W11486360, and AP7218602. Often replaced as a pair with the cold water inlet valve (W11688995, sold separately). Installs in 10–15 minutes with basic hand tools.
Quick Answer
The XPARTCO W11688994 Washer Water Inlet Valve (Hot) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers that aren't filling with hot water, fill slowly with hot water, can't reach hot or warm wash temperatures, or have continuous water dripping into the tub when off. Red/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036928, W11316255, W11486360, AP7218602. Often paired with the cold water valve (W11688995, sold separately).
Common Problems This Part Fixes
Washer not filling with hot water — valve solenoid not opening when commanded
Washer filling slowly with hot water — valve partially clogged or weak solenoid
No hot or warm water in selected wash temperatures — only cold water flowing in
Hot wash cycle running cool — hot valve not delivering normal flow
Water continuously dripping into the tub when the washer is off — hot valve stuck open or not fully closing
Water leaks at the hot valve body — internal seal failure
Wash cycles taking much longer than normal due to slow hot fill
Fill-related error codes when hot fill is required by the selected cycle
Replaces Part Numbers
This hot water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11688994, W11316255, W11036928, W11486360, 4983330, AP7218602, AWP46795, EAP17216729, FIX17216729, OEM21655815, PD00085626, PS17216729.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hot water inlet valve is compatible with select front-load washers from the following brands:
Whirlpool front-load washers — 7MWFC9822HC1, 8TWFC6810LW0, WFC682CLW0, WFC6810LW0, WFC9820HC0, WFC9820HW0 series
Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series
Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series
Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series
Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series
Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series
Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series
Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series
Maytag front-load washers — MHW5630HC0-HC3, MHW5630HW0-HW3, MHW6630HC0-HC3, MHW6630HW0-HW3, MHW8630HC0-HC4, MHW8630HW0-HW4 series
Amana front-load washers — NFW5800HW0, NFW5800HW1, NFW5800HW2, NFW5800HW3, NFW5800HW4 and related models
Inglis front-load washers — IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4 and related models
KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models
Kenmore / Sears front-load washers — select Whirlpool-built models
Note: This is the hot water inlet valve (typically red). The matching cold water inlet valve is part number W11688995 (typically blue). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering.
Key Features
Aftermarket replacement built to OEM-equivalent quality standards
Controls the flow of hot water into the washer during fill cycles
Solenoid-actuated — opens precisely when the control board calls for hot water and closes the moment the call is dropped
1/2" NPT threaded inlet for standard washer supply hose connection
Dimensions: approximately 3" H x 4" W x 3" L
Red and white plastic body with metal solenoid coil — heat-resistant construction designed for hot water cycle pressure and temperature
Replaces W11036928, W11316255, W11486360, AP7218602, and PD00085626
Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers
Often replaced together with the cold water inlet valve (W11688995, sold separately) as a paired repair
Quick DIY repair — installs in 10–15 minutes with basic hand tools
Product Specifications
Part Number
XPW11688994
Part Type
Washer Water Inlet Valve (Hot)
Condition
Aftermarket Replacement
Application
Front-Load Washers (Whirlpool platform)
Water Type
Hot (paired cold valve is W11688995)
Inlet Thread
1/2" NPT
Dimensions
Approximately 3" H x 4" W x 3" L
Color
Red / White
Material
Plastic / Metal (heat-resistant)
Often Paired With
Cold Water Inlet Valve (W11688995, sold separately)
Compatible Brands
Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Important: if the washer has just been running a hot cycle, allow the hot supply hose and valve to cool before handling — hot water can scald. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the hot valve is typically red. Disconnect the hot water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688994 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the hot supply hose at the wall, restore water and power, and run a test cycle on a hot or warm setting to confirm normal hot water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the cold water valve (W11688995) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves.
Frequently Asked Questions
My washer isn't filling with hot water — is the hot valve the problem?
Likely, yes — that's the most common symptom of a failed hot water inlet valve. Before replacing, do a few quick checks: 1) confirm the hot water supply at the wall is turned on and your home actually has hot water at that connection (test the faucet nearby); 2) check the supply hose for kinks or pinches; 3) inspect the inlet screen on the back of the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean, but the washer still won't get hot water, the W11688994 valve solenoid has likely failed and replacing it will resolve the issue.
My washer fills but my hot wash isn't actually hot — could it still be this valve?
Yes — when the hot inlet valve is partially failed (opening but not fully, or opening only briefly), the washer may complete its fill cycle by drawing extra cold water to compensate, but the resulting mix is much cooler than the selected wash temperature should be. If you've confirmed your home's hot water is hot, the supply hose is good, and you're still ending up with lukewarm "hot" washes, the hot valve is a likely cause. Replacing it restores proper hot water delivery and accurate wash temperatures.
Should I replace the cold water valve at the same time?
Yes, it's strongly recommended. The hot and cold inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching cold water valve is part number W11688995 (blue, sold separately) and is also available as a paired kit.
My washer is dripping water into the tub even when it's off — could the hot valve be the cause?
Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the cold water supply at the wall and check if dripping continues. If it stops, the cold valve is at fault; if it continues, this hot valve is the cause. Replacing the W11688994 will resolve a leaking hot valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688994 hot water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
