Search results for "dryer thermal fuse"

XPARTCO 675813 Dishwasher Thermal Fuse The XPARTCO 675813 is an aftermarket replacement bimetal thermal fuse (TCO — thermal cut-off) kit compatible with a wide range of Whirlpool-family dishwashers including Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, and Admiral. The thermal fuse is a one-time safety device located on or near the control board that monitors internal temperature. If the dishwasher overheats — due to a blocked vent, malfunctioning heating element, or other fault — the fuse permanently interrupts power to protect the dishwasher and prevent fire hazards. Unlike a resettable thermostat, a blown thermal fuse must be replaced. Once it trips, the dishwasher will show no power and will not start. The kit includes one thermal cutoff fuse with a 2-wire harness (leads extending approximately 18 inches from the fuse), one zip tie, and installation instructions. The fuse body measures 1-1/16" L x 1" W x 7/16" H. The new wiring harness must always be used when replacing the fuse. Installs in 5–15 minutes with basic hand tools. Quick Answer The XPARTCO 675813 Dishwasher Thermal Fuse Kit fixes Whirlpool-family dishwashers that show no power, won't start, have a blank control panel, or stopped mid-cycle with no response. The thermal fuse permanently trips when the dishwasher overheats and must be replaced. Kit includes fuse with 2-wire harness, zip tie, and instructions. Fuse body 1-1/16" L x 1" W x 7/16" H. Always install using the new harness included. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, and more. Common Problems This Part Fixes Dishwasher completely dead — no power, no lights, no response when buttons are pressed Control panel blank with no indicator lights or display Dishwasher stopped mid-cycle and will not restart Dishwasher will not start despite the door being closed and latched No sounds when attempting to start the dishwasher Dishwasher behaves as if it has no power even though the outlet is live Replaces Part Numbers This dishwasher thermal fuse kit directly replaces the following OEM and cross-reference part numbers: 675813, 3375557, 3376359, 675813VP, 679723, AH382828, OEM9345567, AWP39651 PD00002439, EA382828, EAP382828, AP3115186, PS382828. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse kit is compatible with select dishwashers from the following brands: Whirlpool dishwashers Kenmore / Sears dishwashers (Whirlpool-built models) KitchenAid dishwashers Maytag dishwashers Estate dishwashers Crosley dishwashers Inglis dishwashers Roper dishwashers Admiral dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bimetal thermal cut-off (TCO) fuse — permanently interrupts power if the dishwasher overheats, protecting against fire hazard One-time safety device — once tripped, the fuse must be replaced (it does not reset) Rated at 98°C — trips when internal temperature exceeds the safe operating limit Fuse body dimensions: 1-1/16" L x 1" W x 7/16" H; leads extend approximately 18" from fuse Kit includes thermal fuse with 2-wire harness, zip tie, and installation instructions Always install using the new harness included — never reuse the old harness Metal and plastic construction — reliable performance and heat resistance Direct replacement for 675813, 675813VP, 3375557, and 3376359 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 5–15 minutes with basic hand tools Product Specifications Part Number 675813 Part Type Dishwasher Thermal Fuse / Thermal Cut-Off (TCO) Kit Condition Aftermarket Replacement Fuse Type Bimetal thermal cut-off (one-time, non-resettable) Trip Temperature 98°C (208°F) Fuse Body Dimensions 1-1/16" L x 1" W x 7/16" H Lead Length Approximately 18 inches from fuse body Color White / Brown Material Metal / Plastic Kit Includes Thermal cutoff fuse with 2-wire harness, zip tie, instructions Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug or Switch Off Breaker Before Starting Unplug the dishwasher or turn off the circuit breaker before beginning any repair. The thermal fuse is located inside the dishwasher door panel near the control board. Open the dishwasher door and remove all screws from the inner door panel — a Torx bit is typically required on Whirlpool-family models. Carefully lift the inner door panel to expose the control board housing. Remove the black plastic cover over the control board to access the thermal fuse — it is typically on the right side of the board with one wire connected to each terminal. Test the old fuse with a multimeter for continuity (no continuity confirms the fuse has blown). Disconnect the old fuse and its harness. Connect the new 675813 fuse using the new 2-wire harness included in the kit — do not reuse the old harness. Secure the harness with the included zip tie. Reinstall the control board cover, inner door panel, and all screws. Restore power and run a test cycle. Note: If the fuse blows again after replacement, an underlying cause such as a blocked vent, failed heating element, or faulty control board should be diagnosed before replacing the fuse a second time. Tools needed: Torx screwdriver (T15 or T20), Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions What does the dishwasher thermal fuse do? The thermal fuse is a one-time safety device that monitors the internal temperature of the dishwasher. If the temperature rises above the safe operating limit — 98°C in this case — the fuse permanently interrupts the electrical circuit, cutting all power to the dishwasher. This protects both the appliance and your home from fire hazard caused by overheating. Unlike a resettable thermostat, a blown thermal fuse cannot be reset and must be physically replaced. How do I know if my thermal fuse has blown? The most obvious sign is a completely dead dishwasher — no lights, no sounds, and no response when you press any buttons, even though the outlet has power. You can confirm a blown fuse with a multimeter: disconnect the fuse from the harness and test for continuity across its two terminals. A working fuse will show continuity (near-zero resistance); a blown fuse will show no continuity (open circuit). If the fuse tests bad, replace it with the 675813 kit. Why did my thermal fuse blow, and will it happen again? Thermal fuses blow when the dishwasher overheats. Common causes include a blocked air vent, a malfunctioning or shorted heating element, a failed thermostat, or an electrical fault in the control board. If you simply replace the fuse without addressing the root cause, it may blow again. After replacing the fuse, run the dishwasher and monitor for any unusual heat, steam, or burning smell. If the fuse blows again, have the underlying fault diagnosed before ordering another replacement. Why must I use the new harness and not the old one? When a thermal fuse blows, the wiring harness connected to it may have been exposed to the same overheating event that tripped the fuse. The wires or connectors may have degraded or partially melted even if they appear intact. Using the old harness risks a poor connection or a recurring fault. Always install the new 2-wire harness included in the kit to ensure a reliable, safe connection. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, trip temperature, and performance of the original 675813 thermal fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

Genuine OEM WP3387134 Dryer Cycling Thermostat The Genuine OEM Whirlpool WP3387134 is a dryer cycling thermostat, the operating thermostat that controls drying temperature. It switches the heating element off when the dryer reaches its set temperature and back on after it cools, keeping the inside of the dryer at a steady temperature throughout the cycle. This one is rated L155-25: it cuts out at approximately 155°F and cycles back on once the temperature drops about 25°F. When a cycling thermostat fails, the dryer may stop heating, run too hot, or keep heating after the drum has stopped. This is the original Whirlpool part, and it fits a wide range of Whirlpool-built dryers sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana, and other brand names. Quick Answer The Genuine OEM WP3387134 Cycling Thermostat fixes a Whirlpool-built dryer that isn't heating, runs too hot, or has inconsistent drying temperatures. Rated L155-25, it cycles the heating element off at about 155°F and back on after a 25°F drop. Classic symptom: clothes come out damp or the dryer runs excessively hot, with no sign of a clogged vent. Common Problems This Part Fixes Dryer not heating Dryer running too hot Inconsistent drying temperatures Heat staying on after the drum has stopped Dryer won't start or the timer doesn't advance, if the thermostat has failed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycling thermostat directly replaces the following part numbers: WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187,  EAP11741405, WP3387134VP, AP6008270, AWP47432, EAP11741405, PD00002313, PS11741405, L155-25F These numbers span several generations of Whirlpool's own part numbering for this thermostat as model lines were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat fits a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana and related dryers, including these examples: Kenmore 11060012000, 11060012001, 11060022010, 11060172000, 11060232000, 11060602990 Numerous additional Whirlpool-built dryer models Note: This is the cycling (operating) thermostat, not the high limit thermostat or the thermal fuse, which are separate safety parts. The models above are a sample, not a full list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool cycling thermostat Rated L155-25: cuts out at about 155°F and cycles back on after a 25°F drop Keeps dryer temperature steady by cycling the heating element on and off Resolves no-heat, overheating, and inconsistent-temperature symptoms Fits Whirlpool, Kenmore, Maytag, KitchenAid, and other Whirlpool-built dryers Medium-difficulty repair with basic hand tools Product Specifications Part Number WP3387134 OEM Part Number WP3387134 Part Type Dryer Cycling Thermostat Condition Genuine OEM Temperature Rating L155-25 (Cuts Out ~155°F, 25°F Differential) Application Whirlpool, Kenmore, Maytag, KitchenAid & Related Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the panel that gives access to the heater housing per your model's service guide, note the wire terminal positions, and disconnect them from the old thermostat. Remove the thermostat, install the new one in the same position, and reconnect the wires. A screwdriver and needle-nose pliers are typically all you need. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating. Frequently Asked Questions My dryer isn't heating or runs too hot. Is this the part I need? A failed cycling thermostat can cause either symptom. It may stay open and prevent heat, or stay closed and let the dryer overheat. Check for a clogged vent and test the thermostat for continuity before replacing it. What's the difference between the cycling thermostat and the high limit thermostat? The cycling thermostat controls normal drying temperature by switching the heating element on and off. The high limit thermostat and thermal fuse are separate safety devices that cut power if the dryer overheats. This listing is for the cycling thermostat only. How do I test this thermostat? With the dryer unplugged and the wires removed, check for continuity across the terminals with a multimeter at room temperature. A properly working cycling thermostat should show continuity when cool. No continuity means it has failed. Will this fit my dryer? It fits many Whirlpool-built dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

9759242 Oven Thermal Fuse  This non resettable oven thermal cut out fuse acts as a safety cutting power to the oven if it becomes over heated. Replaces Part Numbers:  WP9759242, 9759242, 4452223, OEM18042050, AP6014015, PS11747248, WP9759242VP Description: This Thermal Fuse is a Genuine part for specific KitchenAid, Kenmore, Whirlpool oven models. It acts as a safety device that cuts off power to the oven if it overheats, preventing potential damage or fire hazards. Common causes of a bad thermal fuse can include prolonged exposure to high temperatures, electrical surges, or faulty oven components that cause overheating. When the fuse blows, it disrupts the electrical circuit, rendering the oven inoperative until the fuse is replaced.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WE04X20685 Genuine OEM GE Dryer Thermistor The WE04X20685 is a genuine GE OEM center outlet thermistor for GE dryers, and also fits select Hotpoint, RCA, and Kenmore models. This thermistor monitors exhaust air temperature and communicates real-time readings to the control board, letting it track how the dryer is operating throughout the cycle. Importantly, this thermistor is not part of the heating circuit itself, so it's unlikely to be the cause of a dryer that won't heat or produces too much or too little heat. Instead, when this thermistor malfunctions, it typically affects cycle timing or triggers a fault code, since the control board is receiving inaccurate or missing temperature data from this specific sensor location rather than losing its ability to regulate the heating element. A healthy thermistor reads approximately 100K ohms at room temperature. Common failure causes include moisture exposure gradually degrading the electronics over time, or physical stress damaging the thin connecting wires. Before assuming this thermistor is the cause of any symptom, it's worth confirming your exhaust venting has good airflow and is free of obstructions. It directly replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518. Quick Answer The WE04X20685 Genuine OEM GE Dryer Thermistor fixes GE, Hotpoint, RCA, and Kenmore dryers with incorrect cycle timing or a fault code related to this sensor. Reads approximately 100K ohms at room temperature. Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518. This thermistor is not part of the heating circuit — it's unlikely to be the cause of a no-heat or overheating problem, but can affect cycle timing or trigger a fault code if defective. Common Problems This Part Fixes Incorrect or inconsistent cycle timing Fault code related to this thermistor or temperature sensing Erratic cycle behavior not explained by a heating element or thermal fuse issue Control board receiving inaccurate temperature data from this sensor location Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermistor directly replaces the following OEM and cross-reference part numbers: WE04X20685, WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is compatible with select GE dryers, and also fits select Hotpoint, RCA, and Kenmore dryers built on the GE platform. Note: This is a center outlet thermistor and is not in the heating circuit — a different function from some other GE thermistors that do regulate heat output directly. Always verify your full model number before ordering, since GE uses different thermistor designs and resistance ratings across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified resistance curve and mounting fit Center outlet thermistor monitors exhaust air temperature and reports it to the control board Not part of the heating circuit — affects cycle timing and fault codes rather than heat output Reads approximately 100K ohms at room temperature Direct drop-in replacement matching the original mounting and wiring Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518 Compatible with GE, Hotpoint, RCA, and Kenmore dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WE04X20685 Part Type Dryer Center Outlet Thermistor Condition Genuine OEM Brand GE In Heating Circuit No Typical Resistance Approx. 100K ohms at room temperature Function Monitors exhaust air temperature and reports to the control board Repair Difficulty Easy Quantity 1 thermistor Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Check Venting Before Assuming This Sensor Is At Fault Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Before replacing this thermistor, confirm that airflow at the home's outside vent hood is good and that the dryer's venting is free of obstructions, since this thermistor is not part of the heating circuit and won't cause a heating problem on its own. Remove the back panel of the dryer, typically secured with several screws, to access the thermistor's mounting location. Test the old thermistor with a multimeter for electrical continuity to confirm it's actually faulty before replacing it. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old thermistor and remove it from its mounting position. Install the new WE04X20685 in the same position, reconnect the wire terminals, and reattach the back panel. Restore power and run a test cycle to confirm normal cycle timing with no fault codes. Tools needed: Phillips or nut driver (model-dependent), multimeter, work gloves. Frequently Asked Questions My dryer isn't heating. Is this thermistor the cause? Unlikely. This is a center outlet thermistor and is specifically not part of the dryer's heating circuit, so a fault here is unlikely to explain a no-heat or overheating symptom. If your dryer isn't heating, check the thermal fuse, heating element, or high-limit thermostat first. This thermistor is more likely to be the cause if you're seeing incorrect cycle timing or a specific fault code instead. What symptoms does this thermistor actually cause when it fails? Since this sensor feeds temperature data to the control board without being in the heating circuit itself, a failure here typically shows up as incorrect cycle timing or a fault code related to this specific sensor, rather than affecting how hot or cold the dryer runs. Should I check anything else before replacing this part? Yes — confirm your dryer's exhaust venting has good airflow and no obstructions before assuming this thermistor is at fault, since venting issues can cause a range of symptoms that might otherwise be mistaken for a sensor problem. This is a quick check worth doing first. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original resistance curve and mounting configuration of the thermistor originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat The XPARTCO 6931EL3001F is an aftermarket replacement dryer rear hi-limit heater thermostat compatible with select LG and Kenmore electric and gas dryers. The hi-limit thermostat is a safety switch mounted on the heater housing that monitors the temperature at the heating element. If the heater temperature exceeds the safe operating limit, the thermostat opens its contacts to cut power to the heating element, protecting the dryer and its contents from overheating. When cooled, the thermostat resets automatically — but if it fails internally, it may remain open permanently, causing the dryer to produce no heat despite the thermal fuse and other components being intact. Rated L125-31C, 250V, 25A, this 3-terminal thermostat measures 2"L x 1-3/4"W x 1-1/4"H with approximately 1-5/8" between mounting holes (center to center). It is constructed from metal and plastic in gray/black and mounts directly on the heater housing. It directly replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482, and PD00023316. Often replaced together with the 6931EL3003D thermal fuse — both mount on the heater housing and work as a system to protect the dryer from overheating. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat fixes LG and Kenmore dryers with no heat where the thermostat has failed open. Rated L125-31C, 250V/25A, 3 terminals. 2"L x 1-3/4"W x 1-1/4"H, ~1-5/8" between mounting holes. Mounts on heater housing. Test with multimeter — should show closed continuity at room temperature. Often replaced together with 6931EL3003D thermal fuse. Replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482. Common Problems This Part Fixes Dryer produces no heat — hi-limit thermostat has failed open and is permanently interrupting the heater circuit Dryer takes much longer than normal to dry a load Dryer tumbles normally but generates no heat during the cycle No heat even after the thermal fuse has already been replaced — thermostat also failed Dryer overheating intermittently — thermostat not opening at the correct temperature Multimeter test shows open circuit (no continuity) across the thermostat at room temperature Replaces Part Numbers This hi-limit thermostat directly replaces the following OEM and cross-reference part numbers: 6931EL3001F, 1377779, AH3530482, ALG51960, EA3530482, EAP3530482, AP5072172, PD00023316, PS3530482 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hi-limit thermostat is compatible with select LG and Kenmore electric and gas dryers. Compatible models include LG DLE, DLG, DLEX, DLGX, and DLB series dryers, and Kenmore 796-series dryers built on the LG platform. LG electric dryers — DLE series (DLE2050W, DLE3777W, DLE5955W and related models) LG electric dryers — DLEX series (select models) LG gas dryers — DLG series (DLG2051W, DLG3788W and related models) LG gas dryers — DLGX series (select models) LG electric and gas dryers — DLB series (select models) Kenmore / Sears dryers — 796-series (LG-built models) Tip: When replacing the 6931EL3001F thermostat, also replace the 6931EL3003D thermal fuse at the same time. Both mount on the heater housing and are commonly replaced together — an overheating event that causes one to fail typically stresses both. Key Features Hi-limit heater thermostat — safety switch that cuts power to the heating element if heater temperature exceeds safe limits Auto-resets when cooled — but a failed thermostat that remains open causes permanent no-heat Rated L125-31C, 250V, 25A — correct specifications for compatible LG and Kenmore dryers 3-terminal design — matches the original wiring configuration on compatible heater housings Dimensions: 2"L x 1-3/4"W x 1-1/4"H; ~1-5/8" between mounting holes (center to center) Metal and plastic construction (gray/black) — heat-resistant materials for heater housing application Mounts directly on the heater housing — accessible from the dryer back panel Often replaced together with 6931EL3003D thermal fuse for a complete heater housing thermal repair Test with multimeter before replacing — should show closed continuity at room temperature Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6931EL3001F Part Type Dryer Rear Hi-Limit Heater Thermostat Condition Aftermarket Replacement Application LG and Kenmore Electric and Gas Dryers Thermostat Rating L125-31C — auto-resets after cooling Voltage 250V Amperage 25A Terminals 3-terminal Dimensions 2"L x 1-3/4"W x 1-1/4"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Gray / Black Material Metal / Plastic Location Heater housing (rear of dryer) Normal Behavior Closed continuity at room temperature Often Replaced With 6931EL3003D Thermal Fuse Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heater housing. The 6931EL3001F thermostat is mounted on the heater housing — it is the 3-terminal component with gray/black housing. Before removing it, test it with a multimeter: disconnect the wires and probe the terminals. At room temperature a working thermostat shows closed continuity. An open reading confirms failure. Photograph the 3-wire connections before disconnecting — reconnecting in the correct positions is important. Remove the 2 mounting screws and lift the old thermostat off. Install the new thermostat in the same position with the 2 mounting screws and reconnect the wires in the same positions. While the heater housing is accessible, also test and replace the 6931EL3003D thermal fuse if needed. Reinstall the back panel, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, multimeter. Frequently Asked Questions What is the difference between the 6931EL3001F thermostat and the 6931EL3003D thermal fuse? Both are mounted on the heater housing and protect the dryer from overheating, but they work differently. The 6931EL3001F is a resettable hi-limit thermostat rated L125-31C — it opens when the heater temperature gets too high and resets automatically when cooled. The 6931EL3003D is a one-time thermal fuse that permanently interrupts the circuit if the temperature exceeds its rated limit — once blown, it cannot reset and must be replaced. Both should show closed continuity at room temperature when working. Because both are on the heater housing and experience the same thermal stress, replacing both at the same time is recommended. How do I test the 6931EL3001F thermostat with a multimeter? Unplug the dryer and disconnect all three wires from the thermostat terminals. Set your multimeter to continuity or resistance mode. At room temperature, a working 6931EL3001F thermostat should show closed continuity (near-zero resistance) across its contacts. If your multimeter reads open circuit (no continuity / OL), the thermostat has failed and needs replacement. Since this thermostat auto-resets when cooled, always test at room temperature — testing while the dryer is still warm may give a false open reading if the thermostat has legitimately opened due to heat. My LG dryer has no heat but the thermal fuse is good — could it be the thermostat? Yes — when the thermal fuse tests good but there is still no heat, the hi-limit thermostat (6931EL3001F) is the next most common culprit. A thermostat that has failed internally may remain permanently open even at room temperature, cutting power to the heating element exactly as a blown thermal fuse would. Test the thermostat with a multimeter for continuity. Also check the cycling thermostat (6931EL3002M) and the thermistor (6323EL2001B) — all three are part of the LG dryer thermal control system and any one of them can cause a no-heat condition. What does the "L125-31C" rating mean? The L125-31C rating describes the thermostat's operating parameters. L125 means the thermostat opens (trips) when the temperature reaches approximately 125°C (257°F). The 31 indicates the reset differential — the thermostat resets when the temperature drops approximately 31°C below the trip point, around 94°C (201°F). This rating ensures the thermostat allows the heater to operate at normal drying temperatures while protecting against dangerous overheating. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from metal and plastic to match the L125-31C rating, dimensions, and 3-terminal configuration of the original 6931EL3001F hi-limit heater thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 35001092 Dryer Thermostat – Replaces WP35001092 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Maintain proper dryer temperature and consistent drying results with the XPARTCO 35001092 Dryer Thermostat. This High Limit Thermostat is a replacement part for specific dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards. Replaces Part Numbers WP35001092, 35001092, 1122485, PD00004704, EAP11741822, AP6008682, PS11741822.  Compatibility This replacement dryer thermostat fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature cycling performance 🌡️ Accurate Heat Regulation – Maintains safe, consistent drying temperatures 🔧 Reliable Thermal Control – Helps prevent overheating and heat loss 💰 Cost-Effective Repair – Quality alternative to OEM thermostats 🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or blown fuses 📐 Product Specification Part Number: 35001092 Component Type: Dryer Operating Thermostat Application: Heater or exhaust temperature regulation Material: Heat-resistant metal thermostat housing Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear access panel. Locate the thermostat on the heater housing or exhaust duct. Disconnect wiring and remove the old thermostat. Install the new XPARTCO 35001092 thermostat. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

ERP DC47-00015A Dryer Thermostat Fits Specific Samsung, Whirlpool Dryer models. non-resettable dryer thermostat. Description: This Dryer Thermal Fuse is a exact replacement Part that is situated on the heating element housing for specific Samsung, Whirlpool dryer models. It meticulously measures the air temperature within the dryer drum and adjusts the heat to maintain the optimal drying temperature. In situations where your dryer doesn't start, fails to dry clothes effectively, or doesn't produce heat, a faulty thermal fuse might be the cause. Replaces Part Numbers:DC47-00015A, 2068544, 35001091, 1122484, AH2038382, DC47-00015A, EA2038382, AP4201892, PS4205212, AP4045835, PS2038382. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

XPARTCO W10711017 Range Vent Hood Thermal Fuse The replacement W10711017 Range Vent Hood Thermal Fuse is designed for Jenn-Air range hood models. This replacement fuse protects the range hood’s electrical system (e.g., fan or motor circuits) from overheating or power surges. Ideal for restoring functionality to Jenn-Air range hoods experiencing issues like no power, fan failure, or intermittent operation. This fuse is located on hood control board. Note: Disconnect power before installation. Verify voltage and amperage compatibility with your appliance model. Replaces part numbers: W10711017, AP5949884, PS10057091. Compatibility (W10711017): Compatible with select Jenn-Air range hood models, including but not limited to: Jenn-Air: JXI8736DS00, JXI8742DS00, JXI8936DS00, JXW8736DS00, JXW8936DS00. Verify your model number or contact our support team for assistance. Key Features (W10711017): ✅ Brand Compatibility: Fits select Jenn-Air range hood models. 🔥 Specifications: Replacement thermal fuse, specifications vary by model (typically 125V–250V, verify amperage), heat-resistant, single-use. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (e.g., screwdriver, pliers); typically installed in 10–15 minutes. 🛡️ Reliable Fixes: Addresses range hood issues like no power, fan failure, or intermittent operation. Installation Notes (W10711017): Safety First: Disconnect the appliance from the power source before installation. Location: Typically found on the control board; consult your model’s manual for exact placement. Tools: Use a screwdriver to access the fuse compartment and pliers to remove and install the fuse. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your microwave or range hood running today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO WE4X750 Gas Dryer Igniter The XPARTCO WE4X750 is an aftermarket replacement flat igniter for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers, replacing GE part WE4X750 and cross-referencing 5303937186 and 4391996. The igniter sits in the burner assembly. It heats up when electrical current passes through it and lights the gas so the dryer can heat. When it wears out or stops glowing, the dryer may run but not heat. Check your model number before ordering, as gas dryers use several different igniters. Quick Answer The XPARTCO WE4X750 Gas Dryer Igniter replaces a worn or non-glowing igniter on a compatible gas dryer from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands. Replaces WE4X750, WE04X0750, 5303937186 and 4391996. Classic symptom: the dryer runs but does not heat, and the igniter doesn't glow. Other parts can cause the same symptom. Common Problems This Part Fixes Gas dryer not heating Igniter not glowing Worn igniter that no longer lights the burner Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer igniter directly replaces the following part numbers: WE4X750, WE04X0750, 276846, AGE25807, AH268196, AP2042796, EA268196, PD00001123, PS268196, 5303937186, 08001685, 08010845, 08015456, 1036069, 3281151, 5303281151, 8001685, F000134211, F134211-000, F134211000, F139743-000, F139743000, G139743-000, AFR17339, AH900236, AP3674313, EA900236, PD00000539, PS900236, Q000622141, Q622141, WQ622141, 4391996, 14211282, 3-4970, 3018, 304970, 41-311, 41-590, 4391996VP, AH373025, AP3109449, AWP39344, DE351, DE363, EA373025, K35-166, K35-455, PD00002514, PS373025 Gas dryers use several different igniters, and they are not interchangeable by number alone. If your old igniter shows a different number, contact our support team and we'll check whether it matches. Compatibility This igniter is listed for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers. Example GE and Hotpoint models that use WE4X750: GE DBL333GA0CC, DCL333GA0AA, DVL223GA0WW, DBL333GY0WW GE DCB330GB0KC, DCD330GY1AC, DH43GW0WW Hotpoint NVL333GY0AA Note: The models above are a small sample of the roughly 36 that retailers list for WE4X750, not a full list, and the example models are GE and Hotpoint. For other brands, confirm fit by your igniter's part number (such as 4391996 or 5303937186) and your model. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the GE WE4X750 flat gas dryer igniter Lights the gas burner so the dryer can heat Installs in the dryer burner assembly Replaces the earlier GE number WE04X0750 and cross-references 5303937186 and 4391996 Product Specifications Part Number XPWE4X750 OEM Part Number WE4X750, 5303937186, 4391996 Part Type Gas Dryer Igniter (Flat) Condition Aftermarket Replacement Quantity 1 Igniter Application Select GE, Hotpoint, Whirlpool, Maytag, Frigidaire & Other Gas Dryers Installation Notes ⚠️ Disconnect Power And Shut Off The Gas Before Installing Unplug the dryer and shut off the gas supply before you begin, and wear work gloves. Remove the panel to reach the burner assembly, note how the igniter and its wiring connect, and remove the old igniter. Handle the new igniter carefully and install it in the same position. Reconnect the wiring, restore power and gas, and test the dryer. If you smell gas at any point, stop and contact a qualified technician. Frequently Asked Questions My gas dryer runs but doesn't heat. Is this the part I need? It can be, if the igniter has worn out and no longer glows. Other parts, such as the gas valve coils or thermal fuse, can cause the same symptom, so confirm the igniter is the problem before replacing it. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace GE part WE4X750. If you specifically need a genuine GE part, contact our support team. Can I use a different gas dryer igniter? Not by number alone. Gas dryers use several different igniters. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my dryer? It is listed for select gas dryers from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM 279311 Dryer Igniter Kit and Bracket The Genuine OEM Whirlpool 279311 is the gas dryer igniter kit with mounting bracket. The silicon carbide igniter glows to light the gas burner and produce the heat that dries your clothes. When the igniter weakens or breaks, the dryer tumbles but doesn't heat, because the gas valve never gets the signal to light the burner. This is the original Whirlpool part. It is listed as a replacement for both round and flat igniters, so it covers a long list of older Whirlpool part numbers for gas dryers sold as Whirlpool, Kenmore, Maytag, and KitchenAid. Quick Answer The Genuine OEM 279311 Igniter Kit and Bracket fixes a gas dryer that spins but doesn't heat because the igniter has burned out or is too weak to open the gas valve. It is for gas dryers only. Classic symptom: the drum turns and the dryer sounds normal, but clothes come out cold and damp, and you never see the igniter glow. Common Problems This Part Fixes Gas dryer runs but doesn't heat Clothes come out damp after a full cycle Igniter never glows, or glows but the burner never lights Cracked, broken, or burned igniter Burner lights unreliably or only some of the time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This igniter kit directly replaces the following part numbers: 279311, 239233, 239300, 239302, 26000279311, 279185, 279311VP, 338899, 338900, 3389895, 340607, 3415, 343128, 41-311, 6-85211, 660991, 685211, 686590, 687399, 691039, 8113, 99912719, AH334180, DE351, DE354, DE363, K35-166, AP3094138, AWP39784, EAP334180, EA334180, PD00002344, PS334180 These numbers span several generations of Whirlpool's own part numbering for this igniter as dryer models were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram. Compatibility This igniter kit is for Whirlpool, Kenmore, Maytag, and KitchenAid gas dryers, including these examples: Whirlpool LGN1000HQ0, LGN1000HQ1, 7MWG66740SG0, 7MWGD72HEDW0 Maytag 7MMGDC300YW0, 7MMGDC410AW0 Kenmore 11097291110, 10687884100, 110279119, 1103401771 Note: This igniter is for gas dryers only. The models above are a sample, not a full list. One supplier lists the kit contents as a 3-inch flat igniter, mounting bracket, 4-inch wire lead and plug. Confirm your model number and the igniter style against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool gas dryer igniter kit with bracket Silicon carbide igniter that lights the gas burner Listed to replace both round and flat igniters Resolves no-heat problems caused by a failed igniter Fits Whirlpool, Kenmore, Maytag, and KitchenAid gas dryers Product Specifications Part Number 279311 OEM Part Number 279311 Part Type Gas Dryer Igniter Kit with Bracket Condition Genuine OEM Fuel Type Gas Dryers Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power and Shut Off the Gas Unplug the dryer and close the gas shutoff valve before beginning, and wear work gloves. Remove the panel that gives access to the burner assembly per your model's service guide, disconnect the igniter's wire connector, and remove the old igniter and bracket. The igniter is fragile, so handle it by the bracket and avoid bumping or squeezing the element. Install the new kit in the same position, reconnect the wires, then restore the gas and power and test the dryer for heat. If you smell gas at any point, stop, ventilate, and call your gas utility. Frequently Asked Questions My gas dryer spins but doesn't heat. Is this the part I need? A failed igniter is a common cause. If you run the dryer and never see the igniter glow, or it glows but the burner doesn't light, test the igniter for continuity. A bad coil on the gas valve or a thermal fuse can cause the same symptom, so check those too. Will this fit an electric dryer? No. This igniter is for gas dryers only. Electric dryers use a heating element instead. Why did my new igniter break? Silicon carbide igniters are fragile. Handle the new one by the bracket, and don't press or bump the element during installation. A weak or restricted gas supply or a faulty gas valve can also make igniters fail early. Will this fit my dryer? It is listed for many Whirlpool-built gas dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8577274 Dryer Thermistor - Compatible with Whirlpool, Kenmore, Maytag Product Description Ensure optimal drying performance with the XPARTCO 8577274 Dryer Thermistor. This replacement temperature-sensing resistor is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers, offering a cost-effective alternative to the original. It monitors air temperature changes during the drying cycle, providing feedback to the control board to regulate heat levels, preventing overheating and ensuring efficient drying. This part addresses issues like prolonged or shortened drying times, inaccurate temperature readings, or error codes, often caused by a faulty thermistor. Note: Includes (1) thermistor (mounting hardware not included). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP8577274, 8577274, 1181075, 3390292, 3406294, 3976615, 772546, ER8577274, WP8577274VP, PD00002401, EAP11746740, AP6013514, PS11746740. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: 3LCED9100WQ0, 7MGGW9200MW3, 7MWGD8300SW1, 7MWGD8500SR1, WED6200SW1, WED8000DW3, WED8300SW0, MEDB880BW0 Kenmore: 110.60884990, 110.6007299, 110.6093699, 110.7095299 Maytag: 7MMGDB850WL0, MVWC565FW0 KitchenAid, Amana, Inglis, Crosley: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, and Crosley dryers. Specifications: High-quality thermistor, approximately 11K Ohms at 70°F (21°C), located on blower housing. Reliable Performance: Monitors drum air temperature to prevent overheating and ensure efficient drying. Easy Installation: Requires 1/4-inch nut driver, small flathead screwdriver, and pliers; typically installed in 15–30 minutes. Effective Fixes: Resolves prolonged or shortened drying times, inaccurate temperature readings, or error codes. Product Specification Part Number: XPARTCO 8577274 Component Type: Dryer thermistor Material: Plastic and metal Electrical Specs: Approximately 11K Ohms at 70°F (21°C), varies with temperature Compliance: Prop 65 warning for California. Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

Choice 8557403 Dryer Thermostat  Replaces Part Numbers: WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386 Description: This Dryer Thermostat is a replacement part for select Kenmore, Maytag, Whirlpool dryer models. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less