Search results for "dryer vent"

XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) The XPARTCO 8318314 is an aftermarket replacement 352°F thermal cutoff fuse compatible with a wide range of Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers. The thermal cutoff fuse is a critical safety device mounted near the heating element housing — it acts as a backup safety in case the high-limit thermostat fails to open. When the air temperature inside the heating element area reaches 352°F, the fuse permanently opens and cuts power to the heater circuit, preventing the dryer from continuing to overheat and creating a fire risk. This is a one-time fuse — once it has tripped, it cannot be reset and must be replaced. White and gray metal/ceramic construction. Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H, with approximately 1-5/8" between mounting holes (center to center). It directly replaces 8318314. Important: when the thermal cutoff blows, the high-limit thermostat (8557403 — sold separately) is often also stressed and should be tested or replaced at the same time. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) fixes Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers that suddenly stopped heating after an overheat event. One-time fuse — 352°F open, must be replaced once blown. 1-1/4"L x 1-1/4"W x 2-3/16"H, ~1-5/8" between mounting holes. Metal/ceramic. Often replaced alongside the high-limit thermostat (8557403, sold separately). Common Problems This Part Fixes Dryer suddenly stopped heating with no warning — thermal cutoff has blown after an overheat event Dryer runs and tumbles normally but produces no heat No-heat fault following a partially blocked exhaust vent or restricted airflow event Multimeter continuity test shows the cutoff has an open circuit (no continuity) Visible damage or discoloration around the thermal cutoff housing from a prior overheat event Repeated no-heat problems where the thermal cutoff has tripped more than once Replaces Part Numbers This thermal cutoff fuse directly replaces the following OEM and cross-reference part numbers: 8318314 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This 352°F thermal cutoff fuse is compatible with select dryers from the following brands: Whirlpool dryers (Elite, Cabrio, Duet, and WED series — select models including WED9200, WED7300, WED7400, WED7600 and related) Maytag dryers (Maxima and MED series — select models including MED3500, MED6000XW, MEDE900VW and related) KitchenAid dryers (select models) Kenmore / Sears dryers — Elite 110-series and related Whirlpool-built models Amana dryers — NED and YNED series (select models including NED7500VW1 and related) Crosley dryers (CED series and related models) Roper dryers (select models) Inglis dryers (select models) Estate dryers (select models) Important — Check Vent Before Restarting: A blown thermal cutoff is almost always the result of restricted dryer airflow. Before replacing this fuse and restoring service, thoroughly clean the dryer's exhaust vent line all the way to the exterior wall outlet, the lint screen, and any internal lint buildup. Installing a new thermal cutoff without fixing the underlying airflow problem will cause the new fuse to blow within a short time, repeating the failure. Key Features 352°F one-time safety fuse — permanently opens to cut power to the heater circuit if the dryer overheats Backup safety device — protects against overheating in case the high-limit thermostat fails to open Cannot be reset — must be replaced once blown Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H; approximately 1-5/8" between mounting holes (center to center) Metal and ceramic construction in white/gray Often replaced together with the high-limit thermostat (8557403, sold separately) as a paired safety repair Compatible with Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8318314 Part Type Dryer Thermal Cutoff Fuse (Safety Fuse) Condition Aftermarket Replacement Application Electric and Gas Dryers (Whirlpool platform) Trip Temperature 352°F Fuse Type One-Time (must be replaced once blown — cannot be reset) Dimensions 1-1/4"L x 1-1/4"W x 2-3/16"H Mounting Hole Spacing Approx. 1-5/8" center to center Color White / Gray Material Metal / Ceramic Often Replaced With High-Limit Thermostat (8557403, sold separately) Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, Estate Installation Notes ⚠️ Unplug Dryer Before Starting — Clean Vent System First Disconnect power before beginning. Wear work gloves to protect your hands. Before installing the new thermal cutoff, thoroughly clean the dryer's vent line — from the lint screen through the duct to the exterior wall outlet, plus any internal lint buildup around the heater housing. A blown thermal cutoff is virtually always caused by restricted airflow; if you don't fix the underlying cause, the new fuse will trip again soon. Access the thermal cutoff by removing the rear (or front, depending on model) access panel of the dryer to expose the heating element housing. The 8318314 thermal cutoff is mounted on or near the heater housing. Photograph the wire connections before disconnecting. Disconnect the wires from the old cutoff and remove the mounting screw(s). Install the new 8318314 cutoff in the same position and reconnect the wires. While the panel is open, this is also the ideal time to test or replace the high-limit thermostat (8557403) — overheat events that blow this fuse often damage that component too. Reassemble the panel, restore power, and run a test heat cycle to confirm normal heat operation. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter, work gloves. Frequently Asked Questions What's the difference between a thermal cutoff, a thermal fuse, and a high-limit thermostat? All three are safety components in a dryer's heating circuit but they serve different roles. The high-limit thermostat (such as 8557403 or 3391914) is a resettable safety switch — it opens when the air gets too hot, then closes again automatically once it cools. The thermal cutoff (8318314, 352°F) is a one-time fuse on the heating element circuit — it blows permanently if the temperature exceeds 352°F, meaning the high-limit thermostat failed to do its job. The thermal fuse (often 3392519) is a separate one-time fuse mounted on the exhaust duct — it blows if exhaust airflow temperature exceeds its rating. Each protects against a different failure mode and is replaced individually when it blows. Why did my thermal cutoff blow in the first place? A blown thermal cutoff is almost always the result of restricted airflow through the dryer. The most common causes are: a clogged or kinked exhaust vent line, a clogged lint screen, lint buildup inside the dryer cabinet near the heater housing, or a failed blower wheel/motor that's not moving enough air. Less commonly, a failed high-limit thermostat (stuck closed) can let the dryer overheat until the thermal cutoff blows as a last-resort safety. Before replacing this part, identify and fix the underlying airflow issue — otherwise the new fuse will blow within a short time. Should I replace the high-limit thermostat at the same time? Yes, it's highly recommended. The thermal cutoff is the second line of defense against overheating — for it to trip, the high-limit thermostat ahead of it likely failed to open at its normal cycling temperature, was stressed by the overheat event, or was already weakened. Replacing the high-limit thermostat (8557403 on many compatible Whirlpool-platform dryers) at the same time is standard practice and ensures both safety components work correctly together. The 279973 kit even bundles a thermal cutoff with a high-limit thermostat for this reason. Can the thermal cutoff be reset like a circuit breaker? No — the 8318314 is a one-time thermal fuse. Once it opens at 352°F, it permanently breaks the electrical circuit and cannot be reset. Some appliance components (like a high-limit thermostat) can reset automatically as they cool, but a thermal cutoff fuse is a single-use safety device by design. If your dryer suddenly stopped heating and a continuity test on this fuse shows an open circuit, it must be replaced. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and ceramic with the same 352°F trip temperature, dimensions (1-1/4"L x 1-1/4"W x 2-3/16"H), and mounting hole spacing (1-5/8" center to center) as the original 8318314 thermal cutoff fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4392065 Dryer Maintenance Kit Replaces 349241T, 341241, WP691366 The XPARTCO 4392065 is an aftermarket dryer maintenance and repair kit containing the three most commonly replaced drum drive components for Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the drum belt (341241), idler pulley (691366), and rear drum support roller kit (349241T) — the three parts that work together to drive and support the dryer drum, and that most frequently cause squealing, thumping, no heat, and drum-not-spinning issues when worn. Replacing all three parts together in a single repair is the recommended approach — since these components wear at similar rates and the dryer must be fully disassembled to access any one of them, doing all three at once saves significant time and cost compared to replacing them individually. The kit contains everything needed: 1 drum belt, 1 idler pulley, 2 drum support rollers, 4 tri-rings, and 2 retaining washers. Installs in 45–60 minutes with basic hand tools. Quick Answer The XPARTCO 4392065 Dryer Maintenance Kit fixes squealing, thumping, no heat, and drum-not-spinning issues in Whirlpool-family 29" dryers in a single repair. Includes 1x 341241 drum belt (92-1/4" x 1/4", 4 ribs), 1x 691366 idler pulley, 2x 349241T drum rollers, 4x tri-rings, and 2x retaining washers. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef dryers. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Dryer drum not spinning — motor runs but belt has broken Clothes not tumbling or drying properly Grinding or rumbling noise from the drum area Dryer drum spinning unevenly or stopping intermittently Belt repeatedly slipping or breaking due to worn idler pulley Drum vibrating excessively due to worn roller bearings What's in the Kit Part 1 of 3 — 1 included 341241 Dryer Drum Belt 92-1/4" L x 1/4" W · 4 ribs, 3 grooves · Neoprene rubber · Wraps around the drum and connects to the idler pulley and motor pulley to drive drum rotation Part 2 of 3 — 1 included 691366 Idler Pulley Sturdy plastic with metal shaft and idler arm · Maintains correct tension on the drum belt between the motor and drum · Self-lubricating bearing Part 3 of 3 — 2 included 349241T Rear Drum Support Roller Kit 2 drum rollers · Reinforced self-lubricating metal bearings, thickened rubber wheel · Supports the rear of the drum as it rotates · Includes 4 tri-rings and 2 retaining washers Replaces Part Numbers Kit (4392065) cross-references: 4392065, 2014, 26000279435, 26000279436, 279435, 279436, 279708, 279708MS, 279709, 279709MS, 279860, 279948, 4392065VP, 587636, 80046, 8106, 8237, 8238, AWP39348, PD00002464, AH373087, EA373087, AP3131942, PS373087. 341241 Belt cross-references: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AP2946843, PS346995, TJ341241. 691366 Idler Pulley cross-references: WP691366, 691366, 239477, 26000691366, 3346, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, AP6010582, PS11743765. 349241T Drum Roller cross-references: 349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AP3098345, PS347627. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select 29-inch large-capacity gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Note: This kit is designed for 29-inch large-capacity Whirlpool-family dryers. If your dryer is a compact or stackable model, verify compatibility with our support team before ordering. Key Features Three-part kit addresses the most common drum drive failures in a single repair — saves time and cost vs. replacing parts individually Belt: 92-1/4" x 1/4", 4 ribs, 3 grooves — premium neoprene rubber resists cracking, heat, and stretching Idler pulley: sturdy plastic with metal shaft and self-lubricating bearing — maintains correct belt tension Drum rollers: 2 included — reinforced self-lubricating metal bearings and thickened rubber wheels for quiet, stable drum support All hardware included: 4 tri-rings and 2 retaining washers — everything needed for complete installation Since the dryer must be disassembled to access any one of these parts, replacing all three at once eliminates repeated teardowns Compatible with 11 major appliance brands on the Whirlpool 29-inch platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392065 Condition Aftermarket Replacement Application 29-inch Gas and Electric Dryers Kit Includes 1x 341241 Drum Belt, 1x 691366 Idler Pulley, 2x 349241T Drum Rollers, 4x Tri-rings, 2x Retaining Washers Belt Length 92-1/4 inches Belt Width 1/4 inch Belt Ribs 4 ribs, 3 grooves Belt Material Neoprene rubber Idler Pulley Material Plastic / Metal Drum Roller Quantity 2 rollers (replace both at same time) Roller Lubrication Self-lubricating bearings — no grease needed Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, then lift the drum out. Remove the old belt, idler pulley, and drum rollers. Install the 2 new 349241T rollers onto the rear bulkhead shafts, pressing the new tri-rings and washers into place. Install the new 691366 idler pulley onto the idler arm. Loop the new 341241 belt around the drum with the ribbed side facing inward, then route it around the idler pulley and motor pulley. Reinstall the drum, reassemble the front and top panels, and restore power. Run a test cycle to confirm quiet operation. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, needle-nose pliers, flat pry tool. Frequently Asked Questions Why should I replace all three parts at the same time? The drum belt, idler pulley, and drum support rollers all work together as a system and wear at similar rates under the same conditions. Since the dryer must be fully disassembled to access any one of these parts, replacing all three in a single repair is far more cost-effective than replacing them one at a time — which would require three separate teardowns. This is the same reason the 4392065 maintenance kit was designed: one repair, all three parts, done. What does each part in this kit do? The 341241 drum belt wraps around the outside of the drum and connects to the idler pulley and motor pulley — the motor drives the belt, which spins the drum. The 691366 idler pulley maintains tension on the belt so it grips the drum and motor pulley properly. The 349241T drum rollers are support wheels mounted on the rear of the dryer that cradle and support the back edge of the drum as it rotates. All three are essential to smooth, quiet drum operation. How is this kit different from the 4392067 repair kit? The 4392065 and 4392067 kits are designed for different Whirlpool-family dryer generations. The 4392065 uses the 341241 belt (92-1/4" x 1/4", 4 ribs) and the 691366 idler pulley, and is for older 29-inch Whirlpool-family dryers. The 4392067 uses the 661570V belt (93-1/2" x 1/4", 4 ribs) and the W10837240 idler arm assembly, and is for newer Whirlpool-family dryers (those with the lint screen inside the door). Use your model number to confirm which kit fits your specific dryer before ordering. Do I need to lubricate the drum rollers after installing? No — the 349241T drum rollers include self-lubricating bearings and do not require any additional grease or oil after installation. Applying grease to self-lubricating rollers is not recommended and can actually attract lint and debris, causing the rollers to wear faster. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM kit, but all three included components are manufactured from premium neoprene rubber, durable plastic, and metal to match the dimensions and performance of the original 4392065 kit parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe and reliable dryer heating with the XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit. This cut-off terminal is a replacement Part for specific Kenmore, Maytag, Roper, Whirlpool dryer models. The kit contains a 309°F Thermal Cut-Off Fuse and a high limit thermostat. In electric dryers, it shuts off the heat if overheating occurs to prevent fire risk. The thermal fuse cuts power while the thermostat regulates the operating temperature. To install, first, unplug the dryer. Use a multimeter to test the old fuse for continuity at room temperature; it should read zero ohms. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers W10900067, 4460718, N197, 197CM, 197, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement dryer thermal cut-off fuse and thermostat kit fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley electric dryers. Example compatible models include (but are not limited to): Whirlpool WED4800XQ, WED4815EW1 Maytag MEDC215EW1 Kenmore 110.6012010 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM temperature and safety specifications 🌡️ Accurate Heat Protection – Helps regulate dryer temperature safely 🔥 Overheat Safety Cut-Off – Prevents damage caused by excessive heat 💰 Cost-Effective Repair – Reliable alternative to higher-priced OEM kits 🛡️ Fixes Common Issues – Resolves no heat, overheating, and thermal shutdowns 📐 Product Specification Part Number: W10900067 Component Type: Dryer Thermal Cut-Off Fuse & Thermostat Kit Includes: Thermal cut-off fuse and high-limit thermostat Application: Heater housing / exhaust temperature control Material: Heat-resistant metal housings Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear access panel. Locate the thermal cut-off and thermostat on the heater housing. Disconnect wiring and remove old components. Install the new XPARTCO W10900067 components in the same positions. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe dryer heating and protection — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 341241 Dryer Drum Belt The XPARTCO 341241 is an aftermarket replacement dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 341241 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, 694088-NC, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 341241 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

🚪 EXP571 Dryer Door Catch This Dryer Door Catch is a replacement part for specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number Exp571. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. ✅ Key Features: High-quality aftermarket replacement Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: WP71002106, WP3389441, 3389441, 71002106, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AP2042209, PS266896, 131658800, AP2107362, PS418433, 5307521419, 10690002, 10690001. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Whirlpool✔️ Maytag✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic ? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the EXP71 dryer door catch from parts-o-matic.com, and enjoy fast, free U.S. shipping!

Read more less

341241 Dryer Genuine OEM Drum Belt The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Genuine OEM part — factory-exact fit, materials, and dimensions DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Genuine OEM Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WE11X29790 Dryer Genuine OEM Heating Element – Compatible with GE & Hotpoint Dryers Product Description Restore proper heat and efficient drying performance with the WE11X29790 Dryer Genuine OEM Heating Element. This Heater Assembly is a Genuine OEM part for specific GE dryer models. This component is responsible for generating the heat required to dry clothes effectively. It consists of a heating element and necessary components that work together to maintain the desired drying temperature, ensuring clothes come out dry and ready to wear.  Common causes of a bad heater assembly can include wear and tear from regular use, overheating, electrical issues, or damage to the heating element itself. A malfunctioning heater assembly can lead to inefficient drying or no heat at all. Replaces Part Numbers WE11X29790, PD00069983, EAP12743382, OEM20945621, AP6981872, PS12743382. Compatibility This Genuine OEM heating element fits select GE and Hotpoint electric dryers. Example compatible models include (but are not limited to):GE GTD33EASK0WW, GTD42EASJ2WW, GTD45EASJ2WSHotpoint HTDX100EM8WW, HTDX100ED6WW Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and safe operation 🔥 Restores Proper Heating – Provides consistent, even heat for effective drying ⚙️ OEM-Grade Construction – Designed to withstand high temperatures and extended use 🛠️ Direct-Fit Installation – No modifications required 🛡️ Fixes Common Issues – Solves dryer running with no heat or weak heating 📐 Product Specification Part Number: WE11X29790 Component Type: Dryer Heating Element Voltage: 240V Wattage: OEM-specified rating Material: High-temperature resistance wire with metal housing Mounting: Heater housing assembly Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer and disconnect power before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear panel. Locate the heating element housing. Disconnect wiring and remove the old heating element. Install the new WE11X29790 heating element in the same position. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore strong, reliable dryer heat — Add to Cart Now for a factory-quality repair!

Read more less

XPARTCO WE18X26 Dryer Lint Screen For gas & electric dryers. Also fits #DE520. Plastic. Dimensions: The rigid plastic frame typically measures roughly 12 5/8 inches long by 2 3/4 inches wide (though some aftermarket variations list slightly different bracket sizes, the standard inner slot size is uniform). Replaces Part Numbers: WE18X26, WE18X0019, WE18X0021, WE18X0023, WE18X0024, WE18X0025, WE18X0026, WE18X0027, WE18X0028, WE18X19, WE18X21, WE18X23, WE18X24, WE18X25, WE18X26E, WE18X26R, WE18X27, WE18X28, AH266250, DE520, EA266250, AP2043582, PS266250.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WE04X20685 Dryer Genuine OEM Thermistor Replaces Part Number: WE04X20685, WE4M336, 4369857, AP5985030, PS11721518. Description: The Thermistor is an OEM replacement part for GE dryers. This temperature-sensing device monitors air exhaust temperatures and communicates real-time readings to the control board. Precise thermistor functioning ensures the heating elements and drum engage safely and appropriately.  

Read more less

WE11X203 Dryer Genuine OEM Heater Restring Coil Kit  Dryer heating element restring kit. This kit replaces the existing heating coil in your dryer.  This Heater restring Coil Replaces WE11X103 Heater Restring Coil.  The diameter of the coil is 1/2" OD it stretches around the pan over the ceramic insulators.   Replaces Part Numbers:WE11X203, AH265619, AP2620176, DE333, EA265619, K35-408, PS265619, WE11X0203, WE11X103C   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE04X10118 Dryer High Limit Thermostat Replaces Part Numbers: WE04X10118, 1089012, AH959918, EA959918, AP3794592, PS959918. Description: This High Limit Thermostat is a replacement part for specific GE dryer models. This safety component is designed to monitor and regulate the dryer's temperature, preventing it from exceeding safe levels. Mounted on the heating chamber or exhaust duct, the high limit thermostat shuts off the heat source or the dryer itself if it detects temperatures that are too high, helping to prevent overheating and potential fire hazards.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less