Search results for "refrigerator control board"

WD21X10367 Dishwasher Genuine Module Control Asm Replaces Part Numbers: WD21X10367, WD21X10269, AH2344315, EA2344315, AP4367159, PS2344315.

Read more less

XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor The XPARTCO W10613606 is an aftermarket replacement compressor start relay and capacitor assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, and Magic Chef refrigerators. The start relay is a small but critical electrical component that plugs directly onto the compressor terminals and provides the initial power surge needed to start the compressor motor. Once the compressor reaches operating speed, the relay drops out — leaving the compressor to run on its own. The capacitor (rated 15µF ±5%, 250VAC) works alongside the relay to store and release the burst of electrical energy needed on startup. When the start relay fails, the compressor cannot start — causing the refrigerator to stop cooling entirely. A failed relay typically produces a clicking sound every few minutes as the compressor tries and fails to start, followed by a short rest, then another attempt. This kit includes both the start relay and the CBB61 capacitor. It directly replaces W10416065, 8208290, 8208368, C8931605, 67003186, 67005560, 67005561, 67005562, 67003764, 8171210, and several additional cross-reference numbers. Installs in under 15 minutes — no tools required in most cases. Quick Answer The XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor fixes refrigerators that are not cooling, are too warm, or are making a repeated clicking sound every few minutes as the compressor tries to start. Plugs directly onto the compressor terminals. Kit includes start relay and 15µF 250VAC CBB61 capacitor. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and more. Replaces W10416065, 8208290, C8931605, 67005560, and more. No tools required — installs in under 15 minutes. Common Problems This Part Fixes Refrigerator not cooling — compressor not running Freezer section too warm or not freezing Both refrigerator and freezer compartments gradually warming up Repeated clicking sound every 2–5 minutes from behind or underneath the refrigerator Compressor hums briefly then shuts off without reaching operating temperature Refrigerator runs but cannot maintain set temperature Shaking the start relay reveals a rattling sound inside — confirms internal failure Replaces Part Numbers This start relay and capacitor kit directly replaces the following OEM and cross-reference part numbers: W10613606, 67005560, 3023300, 67003186, 67003764, 67005561, 67005562, W10416065, 8171210, 8208290, 8208368, W10244032, 302TFBYY, SSP14R302TFR,  AWP41206, C8931605, PD00004905, EAP8746522, AP5787784, PS8746522. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This start relay and capacitor is compatible with select refrigerators from the following brands: Whirlpool refrigerators (side-by-side, French door, bottom-freezer) Kenmore / Sears refrigerators (select Whirlpool-built models) Maytag refrigerators KitchenAid refrigerators Amana refrigerators Jenn-Air refrigerators Admiral refrigerators Crosley refrigerators Dacor refrigerators Hardwick refrigerators Inglis refrigerators Litton refrigerators Magic Chef refrigerators Important: Always verify your refrigerator's model number and compare the old relay's shape and terminal configuration to the new part before installing. Some models may require trimming the wire connector tabs for a proper fit. Contact our support team with your model number if you need confirmation before ordering. Key Features Provides the initial electrical surge needed to start the compressor motor — without it, the compressor cannot run and the refrigerator cannot cool Kit includes both the start relay and the CBB61 run capacitor (15µF ±5%, 250VAC) — everything needed in one package Plugs directly onto the compressor terminals — no wiring or soldering required in most cases Quick rattle test — shake the old relay; if it rattles, the internal contacts have failed and it needs replacement Replaces W10416065, 8208290, C8931605, and over a dozen additional cross-reference part numbers Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Fast DIY repair — installs in under 15 minutes, no tools required in most cases Product Specifications Part Number W10613606 Part Type Refrigerator Compressor Start Relay and Capacitor Kit Condition Aftermarket Replacement Application Refrigerator Compressor (side-by-side, French door, bottom-freezer) Capacitor Type CBB61 Run Capacitor Capacitor Rating 15µF ±5%, 250VAC Kit Includes 1x Start relay, 1x CBB61 capacitor Installation Plug-in — no tools required in most cases Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, Magic Chef Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning. Move the refrigerator away from the wall to access the rear or lower back panel. Remove the rear access panel by unscrewing the retaining screws to expose the compressor. The compressor is a large black dome-shaped component — the start relay and capacitor assembly plugs onto the side terminals. Grip the old relay firmly and pull it straight off the compressor pins. Shake it — if it rattles, the internal contacts have failed and replacement is confirmed. Compare the old relay to the new W10613606 to confirm the terminal layout matches. Align the new relay with the compressor pins and press it firmly on. Reinstall the access panel, restore power, and listen for the compressor to start and run normally within a few minutes. Note: Some models may require trimming the wire connector tabs or reversing the connector orientation for a proper fit — do not force the connection. Tools needed: Phillips screwdriver (for panel access only). Frequently Asked Questions What does the compressor start relay do? The start relay plugs onto the compressor terminals and provides the brief but powerful surge of electrical current needed to start the compressor motor from a standstill. Once the compressor reaches operating speed — usually within a second or two — the relay drops out and the compressor runs on its own. Without a working start relay, the compressor cannot start at all, and the refrigerator stops cooling. The capacitor works alongside the relay to store and deliver the extra energy needed on startup. How do I know if my start relay has failed? The most reliable quick test is the rattle test: unplug the refrigerator, pull the start relay off the compressor, and shake it near your ear. A working relay is silent. A failed relay will rattle — the internal contacts have broken free and are loose inside the casing. Another sign is a repeated clicking sound every 2–5 minutes from the back of the refrigerator, where the compressor attempts to start, fails, trips the overload protector, rests, and tries again. If the fridge is warm and you hear clicking, check the relay first. What is the difference between the start relay and the capacitor? The start relay is the switching device that connects and disconnects the start winding of the compressor motor during startup. The capacitor stores a charge and releases it during startup to give the motor the additional torque it needs to get moving under load. Together they work as a startup system for the compressor. This kit includes both — replacing both at the same time ensures the complete startup circuit is fresh and reliable. My fridge is still not cooling after replacing the start relay — what else could it be? If replacing the start relay does not restore cooling, other possible causes include a failed compressor (the compressor runs but no longer builds pressure), a refrigerant leak in the sealed system, a failed start capacitor (if not replaced along with the relay), a bad overload protector, or a faulty main control board. Listen carefully after installing the new relay — if the compressor now starts and runs but the fridge still doesn't cool after several hours, a sealed system issue or refrigerant problem is likely and will require a certified technician. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and terminal configuration of the original W10613606 start relay and capacitor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5303918214 Refrigerator Defrost Thermostat The XPARTCO 5303918214 is an aftermarket replacement defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process. The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214. Quick Answer The XPARTCO 5303918214 Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat. Common Problems This Part Fixes Freezer stays cold but the fresh food refrigerator section runs warm Refrigerator not defrosting on its normal cycle Excessive frost or ice buildup on the evaporator coils Refrigerator or freezer not cooling properly overall Water leaking inside the refrigerator from melting ice buildup Refrigerator running constantly as ice-caked coils reduce cooling efficiency Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers: 5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as: FGHS2631PF4A, FGHS2655PF5A FGHC2331PFAA, FGHC2331PFCA FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA FFSS2614QS6A Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator. Key Features Aftermarket replacement defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker Monitors evaporator coil temperature and controls power to the defrost heater Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure Ships with wiring diagram guidance for a correct connection Direct drop-in replacement — mounts to the original housing location Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214 Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 5303918214 OEM Part Number 5303918214 Part Type Refrigerator Defrost Thermostat Kit Condition Aftermarket Replacement Function Monitors evaporator coil temperature and controls power to the defrost heater Typical Location Rear access panel area, near the ice maker on many compatible models Repair Difficulty Moderate — ice maker removal typically required for access Quantity 1 defrost thermostat kit Compatible Brands Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves. Frequently Asked Questions Do I really need to remove the ice maker for this repair? On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair. My freezer is cold but the fridge is warm. Is this the thermostat? Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air. I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next? Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured to match the temperature threshold, mounting configuration, and function of the original 5303918214 defrost thermostat used in compatible Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10341320 (OE) Refrigerator Water Inlet Valve The W10341320 (OE) is an Original Equipment (OE) replacement dual secondary water inlet valve compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side refrigerators. This dual-solenoid valve controls water flow to two destinations — the refrigerator's water dispenser and the ice maker. Each solenoid opens independently when the control board calls for water at that destination, and closes the moment the call is dropped. When one or both solenoids fail, you lose water at the dispenser, ice production stops or slows, or the valve begins leaking at its connections. Rated 110/120V, 50/60Hz. Dual solenoid: W1 = 20W, W2 = 35W. Important: this is the SECONDARY valve, not the primary water inlet valve — many Whirlpool side-by-side refrigerators use both, and if your primary valve is working fine but you're still losing water or ice, the secondary valve is the likely culprit. It directly replaces WPW10341320, AP6019939, PS11753250, EAP11753250, 1937969, and K-78032. Common repair for leaks at the valve connections. Installs in about 30 minutes with basic hand tools and novice repair experience. Quick Answer The W10341320 (OE) Refrigerator Water Inlet Valve fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore side-by-side refrigerators with no water through the door, an ice maker that won't make ice or makes too little ice, or leaking at the valve connections. Dual secondary valve — dual solenoid (W1=20W, W2=35W), 110/120V, 50/60Hz. Original Equipment (OE) — same design and performance as the factory part, without the OEM label. Replaces WPW10341320, AP6019939, PS11753250, EAP11753250, 1937969, K-78032. This is the SECONDARY valve — not the primary water inlet valve (W10238100). Common Problems This Part Fixes No water dispensing through the door — dispenser solenoid failed Ice maker not making ice — ice maker solenoid failed Ice maker dispensing too little ice — solenoid partially failed or restricted Water leaking from the valve or its connections Water dispenser works but ice maker doesn't (or vice versa) — one of the two solenoids has failed Weak or slow water flow at the dispenser Ice cubes coming out hollow, small, or misshapen from insufficient water fill Valve buzzing or humming without opening Primary valve tests fine but the refrigerator still won't dispense water or make ice Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dual secondary water inlet valve directly replaces the following OEM and cross-reference part numbers: W10341320, WPW10341320, AP6019939, AWP49977, PD00004978, PS11753250, EAP11753250, 1937969, K-78032 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the primary water inlet valve on many of these refrigerators is a different part (W10238100 / WPW10238100) — see the FAQ below on primary vs secondary valves. Compatibility This dual secondary water inlet valve is compatible with select side-by-side refrigerators from the following brands: Whirlpool side-by-side refrigerators — select models (verify with parts diagram) Maytag side-by-side refrigerators — MSB26C6MDE00/DE02, MSB26C6MDH00/DH02, MSB26C6MDM00/DM02, MSB27C2XAB00, MSB27C2XAM00, MSB27C2XAW00, MSC21C6MDM00/DM02, MSC21C6MEZ00, MSC21C6MFZ00, MSS26C6MEZ00, MSS26C6MFB00/FB01, MSS26C6MFW00 and related models Jenn-Air side-by-side refrigerators — JSC23C9EEM00, JSC24C8EAM00/AM01/AM02 and related models KitchenAid side-by-side refrigerators — select models Amana, Magic Chef, Admiral, Norge, Roper side-by-side refrigerators — select Whirlpool-built models Kenmore / Sears side-by-side refrigerators — select Whirlpool-built models Important — This Is the SECONDARY Valve, Not the Primary: Many Whirlpool-platform side-by-side refrigerators use TWO water inlet valves: a primary valve (typically W10238100 / WPW10238100) where the household water line enters the refrigerator, and this dual secondary valve (W10341320) that splits flow between the dispenser and the ice maker. If your primary valve is functioning correctly but you're still not getting water or ice, the secondary valve is the likely culprit. Before ordering, confirm which valve your refrigerator's parts diagram calls for at the position you're replacing. Contact our support team with your model number if you're unsure. Key Features Original Equipment (OE) replacement — produced to the same design and performance standards as the factory part but not sold under the appliance brand's OEM label; provides the same fit and function at a more affordable price Dual secondary water inlet valve — supplies water to both the refrigerator's water dispenser and the ice maker Dual-solenoid design: each solenoid opens independently when the control board calls for water at that destination Electrical specs: 110/120V, 50/60Hz · W1 = 20W, W2 = 35W Resolves "no water through door," "ice maker doesn't make ice," "too little ice," and "leaking at connections" symptoms Common fix for leaks at the valve's water line connections Replaces WPW10341320, AP6019939, PS11753250, EAP11753250, 1937969, and K-78032 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side refrigerators Note: this is the SECONDARY valve — the primary water inlet valve is a different part (W10238100) DIY repair — installs in about 30 minutes with basic hand tools and novice repair experience Product Specifications Part Number W10341320-OE Designation OE (Original Equipment) OEM Part Number WPW10341320 Part Type Refrigerator Dual Secondary Water Inlet Valve Condition OE Replacement Application Side-by-Side Refrigerators (Whirlpool platform) Valve Position SECONDARY (not the primary inlet valve) Solenoids Dual — W1 = 20W, W2 = 35W Voltage 110/120V Frequency 50/60 Hz Supplies Water To Water dispenser + Ice maker Related Part Primary Water Inlet Valve (W10238100 / WPW10238100, sold separately) Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Supply Before Starting — Wear Work Gloves Unplug the refrigerator (or shut off the house circuit breaker for the appliance) and turn off the refrigerator's water supply at the shutoff valve before beginning. Wear work gloves to protect your hands. Safely store any food that could spoil during the repair. Have towels ready — residual water remains in the lines and will spill when disconnected. Pull the refrigerator away from the wall to access the rear. The secondary water inlet valve is typically mounted at the back of the refrigerator, downstream of the primary valve where the household water line enters. Photograph the water line and wire harness connections before disconnecting anything — with two solenoids and multiple water lines, correct reconnection matters. Disconnect the water lines from the valve (use a 1/2" wrench where needed) and catch any residual water with a towel. Disconnect the electrical connectors from both solenoids. Remove the mounting screws holding the valve bracket in place and lift out the old valve. Install the new W10341320 (OE) valve in the same position and orientation, secure the mounting hardware, and reconnect the water lines — tighten fittings snugly without over-torquing. Reconnect the electrical connectors to the correct solenoids, matching your photos. Turn the water supply back on and check every connection for leaks BEFORE pushing the refrigerator back into place. Restore power. Run water through the dispenser for a few minutes to purge air from the lines, and discard the first few batches of ice. Tools needed: Multi-screwdriver, 1/2" wrench, nut driver, towels, work gloves. Frequently Asked Questions What does "OE" mean and how is it different from Genuine OEM? OE (Original Equipment) parts are produced to the same design and performance standards as the original factory part, but they are not sold under the appliance brand's OEM label. They provide the same fit and function as the OEM part at a more affordable price. The W10341320 (OE) water inlet valve matches the electrical specifications (110/120V, 50/60Hz, dual solenoid W1=20W / W2=35W), dual-secondary valve design, connections, and physical fit of the original Whirlpool OEM part, and installs identically. The main difference from a Genuine OEM Whirlpool part is the branding and warranty — the OE version delivers equivalent performance without the OEM price premium. What's the difference between the primary and secondary water inlet valve? Many Whirlpool-platform side-by-side refrigerators use two water inlet valves working in series. The primary valve (typically W10238100 / WPW10238100) is where the household water supply line first enters the refrigerator — it's the main gatekeeper for water entering the appliance. The secondary valve (this W10341320) sits downstream and splits that flow between the water dispenser and the ice maker via its two independent solenoids. Both can fail independently. The key diagnostic: if the primary valve is working correctly (water is reaching the refrigerator) but you're still not getting water at the dispenser or ice from the ice maker, the secondary valve is the likely culprit. Check your model's parts diagram to confirm which valve you need. My water dispenser works but the ice maker doesn't — can this still be the valve? Yes, absolutely. This is a dual-solenoid valve — one solenoid feeds the water dispenser, the other feeds the ice maker. They fail independently. If your dispenser works fine but the ice maker isn't getting water (no ice, or hollow/small cubes), the ice maker solenoid on this valve may have failed while the dispenser solenoid still works. The reverse is also true. Before replacing the valve, also verify the ice maker itself is turned on (check the wire signal arm position) and that the water line to the ice maker isn't frozen or kinked — those produce similar symptoms. Is this a common fix for leaks? Yes — leaks at the water inlet valve's connections are one of the most common reasons this part gets replaced. Over time, the valve body or its fittings can develop cracks or the internal seals can degrade, producing a slow drip that pools behind or under the refrigerator. If you've found water behind your fridge and traced it to the valve area, replacing the valve typically resolves it. When installing the new valve, tighten the water line fittings snugly but don't over-torque them — over-tightening can crack the fitting and create a new leak. Always check all connections for leaks before pushing the refrigerator back against the wall. Should I flush the water lines after installing the new valve? Yes. After the new valve is installed and the water supply is restored, run water through the dispenser for several minutes to purge trapped air from the lines — air pockets cause sputtering and inconsistent flow. Also discard the first two or three batches of ice the ice maker produces, since they may contain air, debris, or residual manufacturing material from the new valve. After that, water and ice should return to normal quality and flow. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool WPW10184813 Refrigerator Genuine OEM Ice Dispenser Motor Genuine OEM ice-dispenser door motor for select Whirlpool-built refrigerators. Product Overview The Whirlpool WPW10184813 Refrigerator Ice Dispenser Door Motor is a Genuine Whirlpool OEM replacement part. It opens and closes the ice chute door during dispenser operation so ice can pass through the chute and the door can reseal afterward. A failed motor can cause the dispenser door to remain stuck open or closed, prevent ice from dispensing correctly, or allow warm room air to enter the chute area. Quick Answer WPW10184813 is the Genuine Whirlpool OEM ice-dispenser door motor that replaces W10184813 and 2305262. Verify the complete refrigerator model number before purchase. Common Problems This Part May Fix Ice dispenser door will not open Ice chute door will not close Ice maker makes ice but ice will not dispense Chute door sticks or operates intermittently Warm air enters around the dispenser chute Frost or moisture develops around the dispenser opening Replaces and Cross-References WPW10184813, 1489085, 2305262, AP6016508, EAP11749796, W10184813, AWP49407, OEM18049533, PD00006398, PS11749796 Cross-reference numbers are provided for identification. Always verify compatibility by complete refrigerator model number. Compatibility Used on select Whirlpool-built refrigerators sold under Whirlpool, KitchenAid, JennAir, Maytag, and Kenmore brand names. Compatible model examples include: GI7FVCXWY00 KSCS25FTMS02 KSRS25FTSS01 KSCS23FVMS02 KSRS25RSBT01 KSCS25FVMS01 KSCS25FTSS00 GC3NHAXVA00 106.56702500 Important: This is only a partial model list. Confirm the complete model number from the refrigerator identification label before ordering. Key Features Genuine Whirlpool OEM part Operates the ice dispenser chute door Replaces W10184813 and 2305262 For select Whirlpool-built side-by-side and French-door refrigerators Helps restore proper dispenser-door opening and closing Product Specifications Manufacturer Part Number WPW10184813 Brand Whirlpool Part Type Refrigerator Ice Dispenser Door Motor Condition New Quality Genuine OEM Application Ice Dispenser Chute Door Package Quantity 1 Motor Installation Notes Disconnect refrigerator power before service. Remove the dispenser trim and front components according to the appliance service procedure. Photograph connector and mechanical linkage positions before disassembly. Inspect the chute door, hinge, spring, and linkage for binding or damage before replacing the motor. Transfer or reconnect the wiring and linkage exactly as originally installed. Reassemble all dispenser parts and verify the chute door opens and fully closes before returning the refrigerator to service. Diagnostic tip: A dispenser that will not release ice can also be caused by an actuator, dispenser switch, control board, auger motor, frozen chute, or mechanical obstruction. Diagnose the dispenser system before replacing parts. Frequently Asked Questions Is WPW10184813 a Genuine Whirlpool OEM part? Yes. WPW10184813 is a Genuine Whirlpool OEM ice-dispenser door motor. Does it replace W10184813? Yes. Whirlpool lists WPW10184813 as the replacement for W10184813 and 2305262. What does this motor do? It opens and closes the dispenser chute door so ice can pass through the chute and the opening can reseal after dispensing. Will it fit every Whirlpool refrigerator? No. Verify the complete refrigerator model number before ordering because dispenser designs vary by model and production revision. Shop With Confidence Genuine Whirlpool OEM replacement part. Verify your complete refrigerator model and original part number before ordering. Genuine OEMIce Dispenser MotorCompatibility SupportFast U.S. Shipping

Read more less

W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve The W11645245 is a genuine Whirlpool OEM dual water inlet valve for Whirlpool-built refrigerators. Mounted at the rear of the refrigerator where the household water line connects, this single valve is the central control point for water flow to two separate features: the ice maker and the door-mounted water dispenser. When either feature calls for water, this valve's solenoids open to admit it and close again once the request is satisfied — since one valve handles both jobs, a failure here can affect the ice maker, the dispenser, or both at the same time. Common causes of failure include mineral and sediment buildup from the household water supply interfering with the valve's internal operation over time, and electrical faults either in the valve itself or in the refrigerator's electronic control board that signals it. A failing dual water valve produces a recognizable set of symptoms: the door dispenser stops delivering water, the ice maker slows down, stops producing ice, or fails intermittently, water leaking around the valve area, or an audible electronic buzzing or humming sound coming from the back of the refrigerator. It directly replaces AP7208917, W11546685, W11446818, W11563296, and PS16875686. As a genuine OEM part, the W11645245 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve fixes Whirlpool-built refrigerators where the door water dispenser stops working, the ice maker slows down or stops making ice, there's a leak near the valve at the back of the refrigerator, or you hear an electronic buzzing or humming sound. Controls water flow to both the ice maker and water dispenser from a single valve. Replaces AP7208917, W11546685, W11446818, W11563296, PS16875686. Before replacing, rule out a simple mineral clog and a faulty control board signal — both can produce identical symptoms to a failed valve. Common Problems This Part Fixes Water dispenser on the refrigerator door has stopped working Ice maker has slowed down, stopped producing ice, or is malfunctioning intermittently Both the ice maker and water dispenser affected at the same time Water leaking around the valve area at the back of the refrigerator Electronic buzzing or humming sound coming from behind the refrigerator Reduced water flow or pressure at the dispenser Valve that hums but doesn't appear to be passing water through Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator dual water valve directly replaces the following OEM and cross-reference part numbers: W11546685, W11446818, W11563296, AP7208917, AWP46513, K-79524K, N-86-QC N, PD00080446, PS16875686 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dual water valve is compatible with select Whirlpool-built refrigerators across the Whirlpool family of brands, including: Whirlpool refrigerators — WRS series (including WRS321SDHZ08) Maytag, Jenn-Air, and Amana refrigerators (select models) KitchenAid, Magic Chef, Admiral, and Norge refrigerators (select models) Roper refrigerators (select models) Select Kenmore and Ikea refrigerators built on the Whirlpool platform Note: This is a dual-function valve serving both the ice maker and water dispenser from a single unit — it is not a hot/cold laundry-style valve pair. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration Dual water inlet valve — controls water flow to both the ice maker and door water dispenser Resolves "dispenser not working," "ice maker slow or not making ice," "leak near the valve," and "buzzing or humming noise" symptoms caused by valve failure Single central valve simplifies diagnosis and replacement compared to separate dedicated valves Direct drop-in replacement — mounts to the original rear connection point Replaces W11546685, W11446818, W11563296, AP7208917, and PS16875686 Compatible with a wide range of Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward DIY repair using basic hand tools Product Specifications Part Number W11645245 Part Type Refrigerator Dual Water Inlet Valve (Ice Maker + Dispenser) Condition Genuine OEM Brand Whirlpool Location Rear of refrigerator, at the household water line connection Function Controls water flow to the ice maker and door water dispenser Connection Type 1/2" water line inlet, NPT threaded Quantity 1 valve Compatible Brands Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Refrigerator Before Starting — Have A Towel Ready Disconnect power at the outlet, and shut off the water supply valve behind or below the refrigerator before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear or bottom of the cabinet where the water supply line connects. Have a towel or shallow pan ready, since residual water will spill out when you disconnect the line. Photograph the wiring and water line connections before disconnecting anything. Disconnect the water supply line from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new W11645245 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Restore the water supply and check the connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the next day to confirm normal operation has returned. Tools needed: Phillips screwdriver, adjustable wrench or pliers, towel or shallow pan, work gloves. Frequently Asked Questions My dispenser stopped working but the ice maker still works. Is this the right part? It's possible, but worth checking a couple of things first, since this valve serves both features from one unit. Confirm the water supply line isn't kinked or restricted, and check the inline water filter for a clog, since a blocked filter can starve the dispenser specifically while the ice maker (which may draw from a different point in the flow path depending on your model) keeps working. If the filter and supply line are clear and the dispenser still won't deliver water, the valve itself is the likely cause. I hear a buzzing or humming sound from the back of the fridge. What does that mean? This is a common symptom of a valve that's receiving an electrical signal to open but isn't passing water through correctly — the solenoid coil energizes and hums, but water flow is restricted or absent, often due to internal mineral buildup or a failing internal mechanism. If you hear this sound whenever the ice maker or dispenser is called on, the valve is a strong suspect. Could the problem actually be my water filter instead of this valve? Yes, it's worth ruling out first. A clogged inline water filter can produce very similar symptoms to a failing valve — reduced dispenser flow, slow ice production, or both. Try replacing the water filter first if it's been a while since the last change; if symptoms persist afterward, the dual water valve is the more likely cause. Could this be a control board issue instead of the valve? It's possible. This valve is triggered electrically by the refrigerator's control board, so a fault there can produce symptoms that look identical to a failed valve — no water reaching the ice maker or dispenser even though the valve itself is fine. If replacing the valve doesn't resolve the issue, the control board is the next component worth investigating. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-function solenoid design and connection configuration as the valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304524953 Genuine OEM Frigidaire Refrigerator Defrost Heater Assembly The 5304524953 is a Genuine OEM Frigidaire/Electrolux replacement defrost heater assembly compatible with select Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore Frigidaire-built refrigerators and upright freezers — including the popular Frigidaire Professional 19 cu. ft. single-door models in the FPRU19F8 and FPFU19F8 series. The defrost heater is mounted near the evaporator coils and periodically activates during the dishwasher's defrost cycle to melt frost buildup that accumulates on the coils. Without functioning defrost, frost continues to build up on the evaporator until it blocks airflow — causing the refrigerator or freezer to lose cooling efficiency, run continuously, and ultimately fail to maintain set temperatures. As a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications, the 5304524953 directly replaces 5304523833, AP6997296, PS16227227, and 4975045. Tip: when replacing the defrost heater, it's a good time to also inspect or replace the paired defrost thermostat and defrost timer/control board — these three components form the defrost system and often fail in sequence. Addressing them together saves a future repair. Installs in 30–45 minutes with basic hand tools. Quick Answer The 5304524953 Genuine OEM Frigidaire Refrigerator Defrost Heater Assembly fixes Frigidaire and related-brand refrigerators and upright freezers with excessive frost or ice buildup on the evaporator coils, freezer or fresh food section too warm, refrigerator running continuously, or food spoiling faster than normal. Genuine OEM. Replaces 5304523833, AP6997296, PS16227227, 4975045. Compatible with Frigidaire Professional FPRU19F8WF0/WF2/WF3/WF4/WF5 and FPFU19F8WF2/WF4/WF5 series, plus Crosley, Electrolux, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore Frigidaire-built models. Often paired with defrost thermostat replacement. Common Problems This Part Fixes Excessive frost or ice buildup on the evaporator coils Freezer section too warm — evaporator coils iced over and blocking airflow Refrigerator section too warm — cold air not circulating because coils are frosted Refrigerator/freezer running continuously without reaching set temperature Food spoiling faster than normal due to inadequate cooling Visible ice sheet on the rear interior wall of the freezer compartment Defrost heater visibly burned through, broken, or showing arcing damage Multimeter continuity test on the heater shows an open circuit (no continuity) Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: 5304524953, 5304523833, 140223390018, 4975045, AFR19119, AP6997296, EAP16227227, PD00083605, PS16227227. 5304524953 is the current production part superseding 5304523833. Contact our support team with your model number if you need confirmation before ordering. Compatibility This defrost heater assembly is compatible with select refrigerators and upright freezers from the following brands: Frigidaire Professional refrigerators — FPRU19F8WF0, FPRU19F8WF2, FPRU19F8WF3, FPRU19F8WF4, FPRU19F8WF5 series (19 cu. ft. single-door) Frigidaire Professional upright freezers — FPFU19F8WF2, FPFU19F8WF4, FPFU19F8WF5 series Frigidaire refrigerators — FPRU19F7WF0 and related FPRU/FPFU series models Electrolux refrigerators and freezers — select Frigidaire-platform models Crosley refrigerators (select Frigidaire-built models) Gibson refrigerators (select models) Kelvinator refrigerators (select models) Tappan refrigerators (select models) Westinghouse refrigerators (select models) Kenmore / Sears refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications — guaranteed fit and performance Defrost heater assembly — periodically melts frost buildup on the evaporator coils to maintain proper airflow and cooling efficiency Direct factory-original replacement — no modifications required Current production part — directly supersedes 5304523833 Replaces AP6997296, PS16227227, and 4975045 (plus 5304523833) Compatible with Frigidaire Professional FPRU19F8 and FPFU19F8 series, plus Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators and upright freezers Often replaced together with the defrost thermostat and defrost timer/control board as a paired defrost-system repair DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 5304524953 Supersedes 5304523833 Part Type Refrigerator/Freezer Defrost Heater Assembly Condition Genuine OEM Application Refrigerators and Upright Freezers (Frigidaire/Electrolux platform) Location Mounted near the evaporator coils Approximate Weight 1.60 lbs Often Paired With Defrost Thermostat, Defrost Timer/Control Board Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Don't Touch Heater with Bare Hands Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heater only by its mounting brackets or end terminals — do NOT touch the heating element directly with bare fingers; skin oils can cause hot spots and shorten the heater's life. The defrost heater is mounted near the evaporator coils, behind the rear interior access panel of the freezer compartment. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access. If there's a heavy ice sheet covering the back wall, allow the freezer to thaw completely or carefully manually defrost the coils before continuing — never break ice off the coils, as this damages the aluminum fins. Once the area is clear, remove the screws securing the rear access panel and lift it away to expose the evaporator coils and the defrost heater. Photograph the wire connections and heater orientation before disconnecting. Disconnect the wire harness connectors from the old heater, release the heater from its mounting clips or brackets, and lift it out. Install the new 5304524953 heater in the same position, ensuring it's properly seated in the mounting brackets, and reconnect the wire harness. While the panel is open, inspect the defrost thermostat for damage — if it's brittle, discolored, or shows visible defects, this is the ideal time to replace it as well. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves, safety glasses. Frequently Asked Questions How do I know if the defrost heater has failed? The most reliable sign is heavy frost or ice buildup on the evaporator coils behind the freezer back panel — when the heater can't melt the frost as designed, ice accumulates until it blocks airflow and cooling efficiency drops. You may also notice the freezer or fresh food section running warm, the compressor running continuously, or food spoiling faster than normal. To confirm with the refrigerator unplugged: remove the rear freezer access panel, disconnect the heater's wire harness, and test the heater's terminals with a multimeter set to continuity mode. A working heater shows continuity (low resistance); a failed heater shows an open circuit (infinite resistance). If you measure no continuity, the heater has burned out and needs replacement. Should I replace the defrost thermostat and timer at the same time? Yes, it's strongly recommended. The defrost heater, defrost thermostat, and defrost timer/control board work together as a system — the timer (or control board on newer models) initiates the defrost cycle, the thermostat monitors the temperature at the coils and terminates the cycle when the coils are above freezing, and the heater provides the heat that melts the frost. When one component fails, the others have typically experienced similar age and stress, and a near-term failure of another defrost component is common. Since the rear access panel must already be off and the components are right next to each other, replacing all three in a single session prevents a repeat repair down the road. Should I manually defrost my freezer before installing the new heater? If there's significant ice buildup on the evaporator coils or rear wall, yes — you need to clear it before installing the new heater. Leave the freezer empty and unplugged with the door open for 12–24 hours (or longer for heavy ice) to let everything thaw naturally. Place towels at the base to catch melt water. Do NOT chip or pry ice off the evaporator coils with any tool — the aluminum fins damage easily and a damaged coil is a far more expensive repair. Once everything is fully thawed and dried, you can proceed with the heater replacement. My refrigerator/freezer has multiple defrost heater-related part numbers — which one do I need? Frigidaire/Electrolux uses different defrost heater part numbers across different generations and models. The 5304524953 is specifically used in the Frigidaire Professional 19 cu. ft. single-door FPRU19F8 series refrigerators and FPFU19F8 series upright freezers, plus a smaller set of related Frigidaire-platform models. Before ordering, confirm your refrigerator or freezer's model number is in the compatibility list above, or check your appliance's parts diagram to verify that 5304524953 (or one of its cross-references 5304523833, AP6997296, PS16227227, 4975045) is the correct part for your specific model. If your unit is a side-by-side, French door, or other style, you may need a different defrost heater. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications. It is the exact same defrost heater assembly installed in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators and freezers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304517587 Dishwasher Switch Assembly Description:  The Switch Assembly is an OEM replacement part for specific Frigidaire dishwasher models. It contains a touchpad and electronic controls that operate wash cycles and drying features.  Replaces Part Numbers:5304517587, 4840235, AP6802340, PS12585690.  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WR60X10318 Genuine OEM GE Refrigerator Evaporator Fan Motor The WR60X10318 is a genuine GE OEM evaporator fan motor assembly used in side-by-side refrigerators, complete with an integrated 2-wire thermistor built right into its 6-pin wiring harness. This motor draws air across the evaporator coil and circulates it through both the fresh food and freezer compartments, while the built-in thermistor reports temperature back to the control board so it can regulate cooling accurately. Because the thermistor and fan motor arrive as a single assembly, a fault in either function shows up together, and replacing this one part addresses both. The harness and plug measure approximately 13-7/8" in length. Common failure causes include worn motor bearings that eventually seize the shaft entirely, debris or ice buildup around the fan blade, and general electrical wear over time. On this side-by-side platform, a classic failure sequence is a bearing that starts out noisy, then progressively worsens until the motor freezes up completely — once the fan stops moving air, the evaporator coil often ices over heavily since moisture keeps accumulating with nowhere for the resulting cold air to go. Symptoms include unusual noise from the freezer, inconsistent or warm temperatures in either compartment, visible frost buildup on the coil, and a refrigerator that runs continuously trying to compensate. It directly replaces AP4981643, PS3487992, EAP3487992, and 1812462. Quick Answer The WR60X10318 Genuine OEM GE Refrigerator Evaporator Fan Motor fixes GE side-by-side refrigerators with unusual noise from the freezer, warm or inconsistent temperatures, frost or ice buildup on the evaporator coil, or a refrigerator running constantly. Complete assembly with integrated 2-wire thermistor on a 6-pin, 13-7/8" harness. Replaces AP4981643, PS3487992, EAP3487992, 1812462. Not the same part as our WR60X10307 or WR60X10185 listings — those are separate motors for different GE refrigerator platforms. Common Problems This Part Fixes Unusual noise — grinding, buzzing, or humming — coming from the freezer compartment Inconsistent or warm temperatures in the fresh food or freezer compartment, or both Visible frost or ice buildup on the evaporator coil Refrigerator running continuously as it struggles to maintain temperature Fan motor bearing noise that has progressively worsened, sometimes ending in the motor seizing entirely Freezer icing over heavily while temperatures in both compartments climb Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X10318, AP4981643, AGE29310, OEM14944938, PD00023381, PS3487992, EAP3487992, 1812462 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE side-by-side refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, and Kenmore refrigerators built on the GE platform. In rare instances, this part is also referenced for compatibility with some LG models. Note: GE uses several different evaporator fan motors across its refrigerator lineup. This WR60X10318 assembly is a separate part from our WR60X10307 and WR60X10185 listings, which serve different model platforms and have their own distinct cross-reference numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Genuine GE OEM part — factory-specified motor, blade, and integrated thermistor design Complete assembly — includes the fan motor plus a 2-wire thermistor built into the 6-pin harness Resolves "unusual noise from the freezer," "warm or inconsistent temperatures," "frost or ice buildup," and "runs continuously" symptoms caused by fan motor failure Approximately 13-7/8" harness and plug length Direct drop-in replacement matching the original mounting and blade fitment Replaces AP4981643, PS3487992, EAP3487992, and 1812462 Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, though side-by-side units can have tight working clearance around the fan Product Specifications Part Number WR60X10318 Part Type Refrigerator Evaporator Fan Motor Assembly (with Thermistor) Condition Genuine OEM Brand GE Application Side-by-Side Refrigerators Integrated Component 2-wire thermistor built into the wiring harness Harness Connector 6-pin Harness/Plug Length Approx. 13-7/8 in. Production Numbers 197D4964G011, FDQT26GE7 Quantity 1 fan motor assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Side-by-Side Units May Have Tight Clearance Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. On side-by-side models, access can be tight: you may need to remove the rear interior panel, the ice maker, and a fan cover to reach the motor, so budget extra time and patience compared to a simpler platform. If the evaporator coil is heavily iced over, let the unit sit unplugged with the door open for several hours, or run a manual defrost, before continuing — ice can make the old motor difficult to remove cleanly and may be masking the actual point of failure. Photograph the 6-pin wiring harness connector and the fan blade's orientation before disconnecting anything. Remove the mounting screws holding the fan assembly in place, unplug the wiring harness connector, and slide the old assembly out of its housing. Slide the new WR60X10318 assembly into the same housing, secure it with the mounting screws, and reconnect the harness connector fully. Confirm the blade spins freely by hand without contacting the housing before reassembling the fan cover, ice maker, and rear panel. Restore power, open the door to test the fan, and monitor both compartments over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, 1/4" and 5/16" nut drivers, work gloves, and a headlamp or flashlight for visibility in tight spaces. Frequently Asked Questions My freezer is heavily iced over and both compartments are warm. Is this the fan motor? Yes, this is a very common failure sequence on this platform. Once the evaporator fan motor's bearings wear out and the motor slows or seizes, air stops circulating away from the coil, moisture keeps condensing on it, and ice builds up heavily. Once that happens, both the freezer and fresh food compartments typically lose cooling together, since neither is getting circulated cold air anymore. Thawing the ice and confirming the fan motor doesn't spin freely by hand will confirm this diagnosis. Does this include the thermistor, or do I need to buy that separately? It's included. This assembly ships with a 2-wire thermistor built directly into the 6-pin wiring harness, so you don't need to source or install a separate thermistor component — replacing this one part addresses both the fan motor and the thermistor together. Why is access so tight on my side-by-side refrigerator? Side-by-side refrigerators tend to pack components more tightly than French door or top-freezer models, and this evaporator fan often sits behind the ice maker and a dedicated fan cover in addition to the rear interior panel. Removing all of these takes more time than a simpler platform, but the fan motor itself installs the same straightforward way once you have access — a headlamp or flashlight helps considerably in the tighter space. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same motor design, fan blade, integrated thermistor, and 6-pin harness configuration as the evaporator fan motor assembly originally installed in your side-by-side refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DA47-00243K Refrigerator Defrost Thermostat The XPARTCO DA47-00243K is an aftermarket replacement defrost bi-metal thermostat compatible with select Samsung French door and bottom freezer refrigerators. This thermostat is a critical component in the automatic defrost system, functioning as a thermal safety device that monitors the temperature of the evaporator coils during the defrost cycle. When the evaporator reaches the preset maximum temperature of 140°F (60°C), the bi-metal thermostat opens the circuit and cuts power to the defrost heater — preventing overheating and damage to the evaporator. It resets and closes again at 104°F (40°C), allowing the next defrost cycle to begin normally. When the thermostat fails, it can cause excessive frost buildup on the evaporator coils, poor cooling performance, or a heater that won't shut off — all resulting in the refrigerator failing to maintain proper temperatures. Quick Answer The XPARTCO DA47-00243K Refrigerator Defrost Thermostat fixes refrigerators with excessive frost buildup, a freezer that is too cold while the fridge is too warm, a heater that won't shut off, or a refrigerator that stops cooling. It is compatible with select Samsung French door and bottom freezer refrigerators and opens at 140°F to protect the evaporator from overheating. Common Problems This Part Fixes Excessive frost or ice buildup on evaporator coils Freezer too cold while refrigerator section is too warm Defrost heater not shutting off after defrost cycle Refrigerator not cooling or maintaining temperature Food spoiling faster than normal Unusual humming or running sounds from the back of the fridge Replaces Part Numbers This thermostat directly replaces the following OEM and cross-reference part numbers: DA47-00243K, 2025696, DA47-00243B, DA47-00243C, DA47-00243J, ASM30257, PD00002154, EAP4140510, AP4403832, PS4140510. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select refrigerators from the following brands: Samsung French door refrigerators Samsung bottom freezer refrigerators Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bi-metal thermal safety device — opens at 140°F (60°C) to cut power to the defrost heater and prevent evaporator overheating Resets automatically at 104°F (40°C) — allowing the next defrost cycle to begin normally Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Restores proper frost-free operation and refrigerator cooling performance DIY-friendly repair — installs with basic hand tools in 30–45 minutes Budget-friendly alternative to OEM at a lower cost without sacrificing performance Product Specifications Part Number DA47-00243K Part Type Defrost Bi-Metal Thermostat Condition Aftermarket Replacement Application Refrigerator Defrost System Open Temperature 140°F (60°C) Close Temperature 104°F (40°C) Terminals 2 Compatible Brands Samsung Installation Notes ⚠️ Safety First — Unplug Refrigerator Before Starting Unplug the refrigerator from the power source before beginning any repair. Safely remove and store any food that could deteriorate while the power is off. Wear work gloves to protect your hands. Access the evaporator coils by removing the rear panel inside the freezer compartment. Disconnect the wiring harness from the old thermostat and clip the new DA47-00243K thermostat onto the evaporator coil in the same position. Reconnect the wiring harness and reassemble the freezer panel. Allow 24 hours for the refrigerator to return to normal operating temperature. Consult your refrigerator's service manual for model-specific instructions. Frequently Asked Questions Will the DA47-00243K fit my Samsung refrigerator? This thermostat is compatible with select Samsung French door and bottom freezer refrigerators. Use the model search above to verify your model, or contact our support team before ordering. What does a defrost thermostat do? The defrost bi-metal thermostat monitors the temperature of the evaporator coils during the defrost cycle. It opens the circuit and cuts power to the defrost heater when the evaporator reaches 140°F (60°C), preventing overheating. It automatically resets and closes again at 104°F (40°C) to allow the next cycle. What are signs that my defrost thermostat needs replacement? Common signs include: excessive frost or ice buildup on the evaporator coils, the freezer running too cold while the refrigerator section is too warm, the defrost heater failing to shut off, or the refrigerator not maintaining proper temperatures and food spoiling faster than normal. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is designed to deliver reliable, long-lasting performance at a more affordable price point. At what temperatures does the DA47-00243K open and close? The thermostat opens (cuts power to the heater) at 140°F (60°C) and closes (resets) at 104°F (40°C). Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WR60X27396 Refrigerator Air Damper Assembly The WR60X27396 is a genuine OEM air damper assembly for GE refrigerators, including side-by-side and bottom-mount models. The damper is a motorized flap that opens and closes to direct cold air from the freezer into the fresh food compartment, which is how the refrigerator keeps the fresh food section at the right temperature. When it sticks open or closed, or its motor stops working, the compartments fall out of balance: the fresh food section can run too warm or too cold, frost can build up, and the damper may make noise as it moves. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent, so the fit and operation match the original. It supersedes the earlier WR31X20918 damper assembly. Quick Answer The Genuine OEM WR60X27396 Air Damper Assembly fixes a GE refrigerator whose fresh food section is too warm or too cold, or has uneven temperatures, frost buildup, or damper noise because the damper is stuck or has failed. Genuine OEM from GE Appliances. Classic symptom: the freezer is cold but the fresh food section is warm, or the fresh food section freezes items, even with normal settings. Common Problems This Part Fixes Fresh food section too warm while the freezer stays cold Fresh food section too cold, freezing food Damper stuck open or closed, causing a temperature imbalance Unusual clicking or buzzing noises when the damper moves Frost or ice buildup that interferes with the damper Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This air damper assembly replaces the following part numbers: WR60X27396, 4590355, WR09X10065, WR31X20918, WR9X10065, AGE29713, AP6280910, EAP12172988, PD00047584, PS12172988. WR60X27396 is GE's current number for this damper, superseding WR31X20918. If your old damper or parts diagram shows WR31X20918, this is the matching replacement. Compatibility This damper assembly is listed for GE refrigerators, including: Side-by-side models such as ZISS360DNKSS, ZIS420NNEII, and ZISS480DPESS Bottom-mount models such as CFE26KP2NLS1, CDB36LP2RBS1, GDE21EGKARWW, and ZIC360NHDLH Note: The model list above is only a sample, since one retailer lists over 150 compatible models. Confirm fit by matching the number on your old damper or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM GE damper assembly, not an aftermarket equivalent Motorized damper that regulates cold airflow from the freezer into the fresh food section Restores even temperatures between compartments Authorized by GE for refrigerators using flammable refrigerant such as R600a Supersedes the earlier WR31X20918 Product Specifications Part Number WR60X27396 OEM Part Number WR60X27396 Part Type Refrigerator Air Damper Assembly (Motorized) Condition Genuine OEM Manufacturer GE Appliances Supersedes WR31X20918 Application Select GE Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator before starting, and move perishable food to a cooler or another refrigerator so it stays safe during the repair. Following your model's service guide, remove the panels or covers needed to reach the damper, which sits in the air path between the freezer and the fresh food section. Note the position of the old damper, disconnect its wiring connector, and remove the fasteners holding it in place. Install the new damper in the same position, reconnect the connector, and replace the panels. Restore power and allow time for the temperatures to stabilize before judging the repair. Frequently Asked Questions My freezer is cold but the fresh food section is warm. Is this the part I need? It can be. If the damper is stuck closed, not enough cold air reaches the fresh food section. Before replacing it, check that the vents aren't blocked by food and that frost isn't jamming the damper. A stuck or failed damper is a likely cause when those are clear. My fresh food section is freezing my food. Could this be the damper? Yes. A damper stuck open lets too much cold air in from the freezer, which can freeze items in the fresh food section. My old damper is marked WR31X20918. Will this work? Yes. WR31X20918 is on the Replaces list, and WR60X27396 is its current replacement. If you're unsure, contact our support team with your model number and we'll confirm. Is this a genuine GE part? Yes. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

12002782 Refrigerator Genuine OEM Overload Relay Kit Replaces Part Numbers: 12002782, 1194680, 61005518, AH2004057, EA2004057, OEM12028982, AP4009659, PS2004057. Description: This is a Genuine OEM compressor overload and relay kit for Specific Whirlpool, Maytag, Kenmore Refrigerator models. Kit was recently redesigned by manufacturer.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less