Search results for "refrigerator control board"

5303918214 Genuine OEM Frigidaire Refrigerator Defrost Thermostat The 5303918214 is a genuine Frigidaire OEM defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process. The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214. As a genuine OEM part, the 5303918214 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 5303918214 Genuine OEM Frigidaire Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat. Common Problems This Part Fixes Freezer stays cold but the fresh food refrigerator section runs warm Refrigerator not defrosting on its normal cycle Excessive frost or ice buildup on the evaporator coils Refrigerator or freezer not cooling properly overall Water leaking inside the refrigerator from melting ice buildup Refrigerator running constantly as ice-caked coils reduce cooling efficiency Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers: 5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as: FGHS2631PF4A, FGHS2655PF5A FGHC2331PFAA, FGHC2331PFCA FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA FFSS2614QS6A Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator. Key Features Genuine Frigidaire OEM part — factory-specified temperature threshold and mounting configuration Defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker Monitors evaporator coil temperature and controls power to the defrost heater Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure Ships with wiring diagram guidance for a correct connection Direct drop-in replacement — mounts to the original housing location Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214 Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5303918214 Part Type Refrigerator Defrost Thermostat Kit Condition Genuine OEM Function Monitors evaporator coil temperature and controls power to the defrost heater Typical Location Rear access panel area, near the ice maker on many compatible models Repair Difficulty Moderate — ice maker removal typically required for access Quantity 1 defrost thermostat kit Compatible Brands Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves. Frequently Asked Questions Do I really need to remove the ice maker for this repair? On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair. My freezer is cold but the fridge is warm. Is this the thermostat? Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air. I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next? Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original temperature threshold, mounting configuration, and function of the defrost thermostat originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10498976 Refrigerator Water Inlet Valve Replaces WPW10498976 The XPARTCO W10498976 is an aftermarket replacement refrigerator water inlet valve assembly compatible with select Whirlpool, Maytag, KitchenAid, Kenmore, and Ikea bottom-freezer and French door refrigerators in the WRB, WRF, MBF, GX5, GB9, GB2, and related series. The water inlet valve is a solenoid-operated valve mounted on the back of the refrigerator that controls the flow of water from the household supply line to the ice maker and, on models with a door dispenser, to the water dispenser. When the solenoid coil burns out or the valve seat becomes clogged with mineral deposits, the ice maker stops producing ice, the water dispenser stops working, water trickles weakly, or water leaks from the valve body. Rated 120V, 50/60Hz, 35W solenoid, this valve measures 3-1/2"L x 2-3/4"W x 3"H and includes the valve body and mounting bracket. It connects via 1/4" inlet fitting to the household supply line and uses push-in tube fittings on the outlet side. It directly replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, 2315508, IMV-576, AP6022334, EAP11755667, PD00024636, PS11755667, WP2315576, and WV8047. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W10498976 Refrigerator Water Inlet Valve fixes Whirlpool-family bottom-freezer and French door refrigerators where the ice maker is not making ice, the water dispenser is not working or producing only a trickle, or water is leaking from the back of the refrigerator. 120V/50-60Hz/35W solenoid, 3-1/2"L x 2-3/4"W x 3"H, includes bracket. 1/4" inlet connection. Replaces WPW10498976, W10420082, W10498974, K-78200, 2684516, AP6022334, PS11755667. Compatible with Whirlpool WRB/WRF, Maytag MBF, KitchenAid, Kenmore, and Ikea. Common Problems This Part Fixes Ice maker not producing ice or producing very small cubes due to insufficient water supply Water dispenser not working — no water flows when the lever or button is pressed Water dispenser producing only a trickle — valve partially blocked or solenoid weakening Water leaking from behind the refrigerator near the water valve Ice maker fills but overflows — valve stuck open and not closing properly Humming sound near the back of the refrigerator when requesting ice or water — solenoid energized but valve not opening No water reaching the refrigerator despite supply line being connected and pressurized Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WPW10498976, W10498976, W10420082, AWP50873, EAP11755667, PD00024636, AP6022334, PS11755667.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select bottom-freezer and French door refrigerators from the following brands and series: Whirlpool refrigerators — WRB322, WRB329, WRF535, WRF555, and related WRB/WRF series (French door and bottom-freezer models) Maytag refrigerators — MBF1958, MBF2258, and related MBF series KitchenAid refrigerators — select bottom-freezer and French door models Kenmore / Sears refrigerators — select Whirlpool-built models Ikea refrigerators — select models (Whirlpool-built) Other Whirlpool-platform models including GB9, GB2, GX5, GX2, ET1CH, ET8CH, IX5HH, ED22, and related series Note: Always verify your exact model number before ordering — water inlet valves are model-specific and not universal across all refrigerator configurations. Check that the supply line connection size (1/4") matches your existing supply line before purchasing. Key Features Solenoid-operated valve — opens on command from the refrigerator's control board to supply water to the ice maker and water dispenser Rated 120V, 50/60Hz, 35W — correct electrical specifications for compatible Whirlpool-family refrigerators Dimensions: 3-1/2"L x 2-3/4"W x 3"H — includes mounting bracket for direct installation 1/4" inlet connection — matches standard residential refrigerator supply line diameter Push-in outlet tube fittings — easy connection to existing water supply tubing inside the refrigerator Plastic and metal construction — durable and resistant to mineral buildup Replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, AP6022334, and over 10 additional cross-references Compatible with Whirlpool WRB/WRF series, Maytag MBF series, KitchenAid, Kenmore, and Ikea refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10498976 OEM Part Number WPW10498976 Part Type Refrigerator Water Inlet Valve Assembly Condition Aftermarket Replacement Application Bottom-Freezer and French Door Refrigerators Voltage 120V AC Frequency 50/60 Hz Solenoid Wattage 35W Dimensions 3-1/2"L x 2-3/4"W x 3"H Inlet Connection 1/4 inch Color Brown / Blue / Yellow / Gray Material Plastic / Metal Includes Water valve body and mounting bracket Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Before Starting Unplug the refrigerator and shut off the household water supply valve before beginning. Place a towel and small container under the valve area to catch residual water. Pull the refrigerator away from the wall to access the back lower panel — remove the panel screws to expose the water inlet valve. Photograph the wiring harness connections and water tube connections before disconnecting. Turn off the water supply and disconnect the 1/4" supply line from the valve inlet — use an adjustable wrench, as some compression fittings may be stuck. Squeeze the plastic retaining clips on the outlet tube fittings and pull the internal water tubes free. Disconnect the wiring harness. Unscrew the mounting bracket and remove the old valve. Install the new W10498976 valve with its bracket, reconnect the internal water tubes (push until they click), reconnect the wire harness and supply line. Restore water supply and power. Run a water dispenser test and check for leaks. Tools needed: Phillips screwdriver, adjustable wrench, needle-nose pliers. Frequently Asked Questions What does the refrigerator water inlet valve do? The water inlet valve is an electrically controlled solenoid valve that opens on command from the refrigerator's control board to allow household water pressure to push water through to the ice maker fill tube or the water dispenser. When the ice maker calls for water or you press the dispenser lever, the board sends voltage to the solenoid coil, which opens the valve. When the demand is satisfied, the voltage stops, the spring closes the valve, and water flow stops. A failed solenoid coil — or a valve seat clogged with mineral deposits — prevents the valve from opening or closing correctly, causing no water, weak water, overflow, or dripping. What is the difference between W10498976 and WPW10498976? These are the same water inlet valve. WPW10498976 is the updated Whirlpool OEM part number that superseded the original W10498976. The W10420082 and W10498974 are also cross-references for this same valve from earlier production runs. This aftermarket replacement is compatible with all of these numbers. How do I know if the water inlet valve has failed vs. something else? First confirm the household water supply valve behind the refrigerator is fully open and the supply line is not kinked. Then check the water filter — a clogged filter is one of the most common causes of weak or no water flow and is mistaken for a valve failure. If both supply pressure and the filter are good, test the valve's solenoid coil with a multimeter — a working coil reads 200–500 ohms of resistance; an open circuit confirms failure. If the solenoid tests good but the valve still does not open when the control board sends voltage, the valve seat may be physically clogged with mineral deposits and the valve needs to be replaced. My ice maker is not working but my water dispenser is fine — is it the valve? Possibly — but if the water dispenser works normally, the main valve solenoid is likely functioning. On some refrigerator configurations, the ice maker and the dispenser are controlled by separate solenoid ports on the valve assembly. If only the ice maker port has failed, the dispenser can continue working while ice production stops. Test the ice maker solenoid coil separately. However, a more common cause of ice maker failure with a working dispenser is the ice maker module, freezer temperature, or ice maker shut-off arm — rule out those causes before replacing the valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal to match the electrical specifications and dimensions of the original WPW10498976 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR60X10062 Refrigerator Air Damper Assembly Replaces Part Numbers:WR60X10062, 914163, AH304650, EA304650, AP3184950, PS304650.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WR60X26866 Genuine OEM GE Refrigerator Axial Evaporator Fan Motor The WR60X26866 is a Genuine OEM GE replacement axial evaporator fan motor manufactured by GE to factory specifications, designed as a direct fit for the fresh food section of select GE French door refrigerators, including the CFE28, CFE29, CWE23, CYE22, CYE23, DFE28, DFE29, GFD28, GFE26, GFE27, GFE28, GFE29, GFS26, GFS28, GNE26, GNE29, GYE22, GYS22, PFD28, PFE28, PFE29, PWE23, PYD22, PYE22, PYE23, and ZWE23 series. The evaporator fan motor pulls air through the evaporator coils to remove heat from the circulating air inside the refrigerator. Without a functioning evaporator fan, the refrigerator compartment cannot maintain its target temperature even when the compressor and condenser are running normally — the cold air generated at the evaporator simply isn't being circulated to the food storage areas. The WR60X26866 is a DC motor rated at 13.6V DC, 0.16A, with a fan housing measuring 3-4/7"L x 2"W x 3-1/8"H, plus a multi-color wire harness and plug approximately 11-1/2" long. It includes the axial fan blade and harness as a complete assembly. It directly replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, and PS12172983. Important: if your refrigerator was built between May 2014 and March 2015 with serial range FF–HD, the unit's software must be updated before installing this fan motor — see FAQ below. Installs in 20–30 minutes with basic hand tools. Quick Answer The WR60X26866 Genuine OEM GE Refrigerator Axial Evaporator Fan Motor fixes GE French door refrigerators where the fridge isn't cooling but the freezer is cold, the evaporator coils are frosted over, the ice maker isn't working due to insufficient cooling, or there's loud humming or grinding from the freezer area. Axial fan motor, 13.6V DC, 0.16A. Fan housing: 3-4/7"L x 2"W x 3-1/8"H; harness ~11-1/2"L. Replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, PS12172983. Note: May 2014 – Mar 2015 build refrigerators (serial range FF–HD) require a software update before installation. Common Problems This Part Fixes Refrigerator not cooling properly while the freezer remains cold — classic evaporator fan failure Freezer cold but fridge warm — fresh food compartment air not being circulated Frosty or frozen evaporator coils due to insufficient air circulation Ice maker failure caused by inadequate cooling in the compartment Loud humming, grinding, or buzzing noise from the freezer or fresh food compartment Refrigerator running continuously without reaching set temperature Fan blade not spinning freely or seized when checked by hand Multimeter shows no continuity through the motor windings Replaces Part Numbers This evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE French door refrigerators, including: GE refrigerators — CFE28, CFE29, CWE23, CYE22, CYE23 series (CFE28TP2MBS1, CFE28USHNSS, CWE23SP2MBS1, CYE22TP2MBS1 and related) GE refrigerators — DFE28, DFE29 series (DFE28JELCDS and related) GE refrigerators — GFD28, GFE26, GFE27, GFE28, GFE29 series (GFD28GBLBTS, GFE26GGHEBB and related) GE refrigerators — GFS26, GFS28, GNE26, GNE29 series GE refrigerators — GYE22, GYS22 series (GYE22HMKEES and related) GE refrigerators — PFD28, PFE28, PFE29 series (PFE28KELFDS and related) GE refrigerators — PWE23 series (PWE23KSKDSS and related) GE refrigerators — PYD22, PYE22, PYE23 series (PYE22KSKBSS and related) GE refrigerators — ZWE23 series and select related Café and Profile French door models Important — Software Update Requirement: If your GE refrigerator was manufactured between May 2014 and March 2015 with a serial number in the range FF–HD, the refrigerator's control software must be updated by GE factory service (or via Software Update Module WR98R882802) before installing this fan motor. Installing the new motor without the software update on these affected units may result in improper performance. Check your refrigerator's serial number plate before ordering. Key Features Axial evaporator fan motor for the fresh food section of GE French door refrigerators Pulls air through the evaporator coils to remove heat and circulate cold air through the refrigerator compartment DC motor — rated 13.6V DC, 0.16A — runs on DC voltage from the refrigerator control board Includes the axial fan blade and pre-attached multi-color wire harness with plug Fan housing dimensions: 3-4/7"L x 2"W x 3-1/8"H; harness and plug approximately 11-1/2" long Quiet operation — engineered to minimize hum and vibration in the refrigerator cabinet Plastic and metal construction, black housing with multi-color harness Replaces an extensive list of GE part numbers including WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, and additional cross-references Compatible with GE, GE Café, and GE Profile French door refrigerators in the CFE, CWE, CYE, DFE, GFD, GFE, GFS, GNE, GYE, GYS, PFD, PFE, PWE, PYD, PYE, and ZWE series Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR60X26866 Part Type Refrigerator Evaporator Fan Motor (Fresh Food / Axial) Condition Genuine OEM Application GE French Door Refrigerators Voltage 13.6V DC Amperage 0.16A Fan Type Axial Fan Housing Dimensions 3-4/7"L x 2"W x 3-1/8"H Harness Length Approximately 11-1/2 inches Color Black housing with multi-color harness Material Plastic / Metal Includes Axial fan motor assembly with harness Software Update Required For May 2014 – Mar 2015 builds (serial range FF–HD) — use WR98R882802 Compatible Brands GE, GE Café, GE Profile Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor for the fresh food section is mounted on the back wall of the fresh food (refrigerator) compartment, behind an access panel. Take a photo of the existing fan position and wire harness routing before disconnecting. Remove the shelves and any internal components blocking access to the back wall, then remove the screws holding the rear access panel in place. Disconnect the fan motor's wire harness connector and remove the mounting screws securing the old motor. Note the fan blade orientation on the motor shaft. Install the new WR60X26866 motor assembly in the same position with the blade facing the same direction, reconnect the wiring harness, and reinstall the mounting screws and access panel. Replace the shelves and other internal components, restore power, and confirm the fan spins and the refrigerator cools properly. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions My fridge is warm but my freezer is cold — is the evaporator fan motor the problem? Yes — this is one of the most recognizable symptoms of evaporator fan motor failure on GE French door refrigerators with a separate fresh food evaporator. The freezer side has its own cooling circuit and remains cold, while the fresh food side relies on this fan to circulate air across its evaporator coils. When the fan fails, the freezer continues working but the fresh food compartment loses its cold air supply, warming up while the freezer stays at temperature. If you also notice frost building up on the evaporator coils behind the back panel of the fresh food compartment, the fan failure is confirmed. What is the software update requirement for May 2014 – March 2015 refrigerators? GE issued a software update for certain refrigerators manufactured between May 2014 and March 2015 (serial range FF–HD) before they could properly support newer revisions of the WR60X26866 evaporator fan motor. If your refrigerator falls in this date and serial range, the control software must be updated before installing this fan motor — either by GE factory service or by using the Software Update Module part WR98R882802. Installing the new fan on an unupdated unit can result in improper performance. Check the serial number plate inside your refrigerator (typically on the left side wall) to confirm whether your unit is affected. Refrigerators built outside this range do not require the update. How do I test if the evaporator fan motor has failed? Unplug the refrigerator, then access the fan behind the rear panel of the fresh food compartment. First, try turning the fan blade by hand — if it doesn't spin freely, is stiff, or seizes, the motor bearing has failed. Next, listen during normal operation — if the motor is unusually noisy or makes a grinding sound, the bearings are worn even if it still spins. Finally, with the unit unplugged and the motor disconnected, use a multimeter on the motor windings to check for continuity. If the windings show no continuity, the motor has failed electrically. Also check for approximately 11–14V DC at the connector when the refrigerator is running — if voltage is present but the motor doesn't spin, the motor has failed. My fridge has two evaporator fans — which one does this replace? Some GE French door refrigerators have separate evaporator fan motors for the freezer and the fresh food sections. The WR60X26866 is the fresh food evaporator fan motor — it's the axial fan located behind the rear panel of the fresh food compartment, not in the freezer. If your symptom is "freezer cold, fridge warm," this is the correct part. If your symptom is "freezer warm" or "ice maker not making ice but fridge is fine," the freezer evaporator fan motor (a different part number) is more likely the cause. Confirm which compartment has the cooling problem before ordering. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same axial evaporator fan motor installed in compatible GE, GE Café, and GE Profile French door refrigerators from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR60X26866 Refrigerator Evaporator Fan Motor The XPARTCO WR60X26866 is an aftermarket replacement axial evaporator fan motor for the fresh food section of select GE French door refrigerators, including the CFE28, CFE29, CWE23, CYE22, CYE23, DFE28, DFE29, GFD28, GFE26, GFE27, GFE28, GFE29, GFS26, GFS28, GNE26, GNE29, GYE22, GYS22, PFD28, PFE28, PFE29, PWE23, PYD22, PYE22, PYE23, and ZWE23 series. The evaporator fan motor pulls air through the evaporator coils to remove heat from the circulating air inside the refrigerator. Without a functioning evaporator fan, the refrigerator compartment cannot maintain its target temperature even when the compressor and condenser are running normally — the cold air generated at the evaporator simply isn't being circulated to the food storage areas. The WR60X26866 is a DC motor rated at 13.6V DC, 0.16A, with a fan housing measuring 3-4/7"L x 2"W x 3-1/8"H, plus a multi-color wire harness and plug approximately 11-1/2" long. It includes the axial fan blade and harness as a complete assembly. It directly replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, and PS12172983. Important: if your refrigerator was built between May 2014 and March 2015 with serial range FF–HD, the unit's software must be updated before installing this fan motor — see FAQ below. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WR60X26866 Refrigerator Evaporator Fan Motor fixes GE French door refrigerators where the fridge isn't cooling but the freezer is cold, the evaporator coils are frosted over, the ice maker isn't working due to insufficient cooling, or there's loud humming or grinding from the freezer area. Axial fan motor, 13.6V DC, 0.16A. Fan housing: 3-4/7"L x 2"W x 3-1/8"H; harness ~11-1/2"L. Replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, PS12172983. Note: May 2014 – Mar 2015 build refrigerators (serial range FF–HD) require a software update before installation. Common Problems This Part Fixes Refrigerator not cooling properly while the freezer remains cold — classic evaporator fan failure Freezer cold but fridge warm — fresh food compartment air not being circulated Frosty or frozen evaporator coils due to insufficient air circulation Ice maker failure caused by inadequate cooling in the compartment Loud humming, grinding, or buzzing noise from the freezer or fresh food compartment Refrigerator running continuously without reaching set temperature Fan blade not spinning freely or seized when checked by hand Multimeter shows no continuity through the motor windings Replaces Part Numbers This evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE French door refrigerators, including: GE refrigerators — CFE28, CFE29, CWE23, CYE22, CYE23 series (CFE28TP2MBS1, CFE28USHNSS, CWE23SP2MBS1, CYE22TP2MBS1 and related) GE refrigerators — DFE28, DFE29 series (DFE28JELCDS and related) GE refrigerators — GFD28, GFE26, GFE27, GFE28, GFE29 series (GFD28GBLBTS, GFE26GGHEBB and related) GE refrigerators — GFS26, GFS28, GNE26, GNE29 series GE refrigerators — GYE22, GYS22 series (GYE22HMKEES and related) GE refrigerators — PFD28, PFE28, PFE29 series (PFE28KELFDS and related) GE refrigerators — PWE23 series (PWE23KSKDSS and related) GE refrigerators — PYD22, PYE22, PYE23 series (PYE22KSKBSS and related) GE refrigerators — ZWE23 series and select related Café and Profile French door models Important — Software Update Requirement: If your GE refrigerator was manufactured between May 2014 and March 2015 with a serial number in the range FF–HD, the refrigerator's control software must be updated by GE factory service (or via Software Update Module WR98R882802) before installing this fan motor. Installing the new motor without the software update on these affected units may result in improper performance. Check your refrigerator's serial number plate before ordering. Key Features Axial evaporator fan motor for the fresh food section of GE French door refrigerators Pulls air through the evaporator coils to remove heat and circulate cold air through the refrigerator compartment DC motor — rated 13.6V DC, 0.16A — runs on DC voltage from the refrigerator control board Includes the axial fan blade and pre-attached multi-color wire harness with plug Fan housing dimensions: 3-4/7"L x 2"W x 3-1/8"H; harness and plug approximately 11-1/2" long Quiet operation — engineered to minimize hum and vibration in the refrigerator cabinet Plastic and metal construction, black housing with multi-color harness Replaces an extensive list of GE part numbers including WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, and additional cross-references Compatible with GE, GE Café, and GE Profile French door refrigerators in the CFE, CWE, CYE, DFE, GFD, GFE, GFS, GNE, GYE, GYS, PFD, PFE, PWE, PYD, PYE, and ZWE series Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR60X26866 Part Type Refrigerator Evaporator Fan Motor (Fresh Food / Axial) Condition Aftermarket Replacement Application GE French Door Refrigerators Voltage 13.6V DC Amperage 0.16A Fan Type Axial Fan Housing Dimensions 3-4/7"L x 2"W x 3-1/8"H Harness Length Approximately 11-1/2 inches Color Black housing with multi-color harness Material Plastic / Metal Includes Axial fan motor assembly with harness Software Update Required For May 2014 – Mar 2015 builds (serial range FF–HD) — use WR98R882802 Compatible Brands GE, GE Café, GE Profile Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor for the fresh food section is mounted on the back wall of the fresh food (refrigerator) compartment, behind an access panel. Take a photo of the existing fan position and wire harness routing before disconnecting. Remove the shelves and any internal components blocking access to the back wall, then remove the screws holding the rear access panel in place. Disconnect the fan motor's wire harness connector and remove the mounting screws securing the old motor. Note the fan blade orientation on the motor shaft. Install the new WR60X26866 motor assembly in the same position with the blade facing the same direction, reconnect the wiring harness, and reinstall the mounting screws and access panel. Replace the shelves and other internal components, restore power, and confirm the fan spins and the refrigerator cools properly. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions My fridge is warm but my freezer is cold — is the evaporator fan motor the problem? Yes — this is one of the most recognizable symptoms of evaporator fan motor failure on GE French door refrigerators with a separate fresh food evaporator. The freezer side has its own cooling circuit and remains cold, while the fresh food side relies on this fan to circulate air across its evaporator coils. When the fan fails, the freezer continues working but the fresh food compartment loses its cold air supply, warming up while the freezer stays at temperature. If you also notice frost building up on the evaporator coils behind the back panel of the fresh food compartment, the fan failure is confirmed. What is the software update requirement for May 2014 – March 2015 refrigerators? GE issued a software update for certain refrigerators manufactured between May 2014 and March 2015 (serial range FF–HD) before they could properly support newer revisions of the WR60X26866 evaporator fan motor. If your refrigerator falls in this date and serial range, the control software must be updated before installing this fan motor — either by GE factory service or by using the Software Update Module part WR98R882802. Installing the new fan on an unupdated unit can result in improper performance. Check the serial number plate inside your refrigerator (typically on the left side wall) to confirm whether your unit is affected. Refrigerators built outside this range do not require the update. How do I test if the evaporator fan motor has failed? Unplug the refrigerator, then access the fan behind the rear panel of the fresh food compartment. First, try turning the fan blade by hand — if it doesn't spin freely, is stiff, or seizes, the motor bearing has failed. Next, listen during normal operation — if the motor is unusually noisy or makes a grinding sound, the bearings are worn even if it still spins. Finally, with the unit unplugged and the motor disconnected, use a multimeter on the motor windings to check for continuity. If the windings show no continuity, the motor has failed electrically. Also check for approximately 11–14V DC at the connector when the refrigerator is running — if voltage is present but the motor doesn't spin, the motor has failed. My fridge has two evaporator fans — which one does this replace? Some GE French door refrigerators have separate evaporator fan motors for the freezer and the fresh food sections. The WR60X26866 is the fresh food evaporator fan motor — it's the axial fan located behind the rear panel of the fresh food compartment, not in the freezer. If your symptom is "freezer cold, fridge warm," this is the correct part. If your symptom is "freezer warm" or "ice maker not making ice but fridge is fine," the freezer evaporator fan motor (a different part number) is more likely the cause. Confirm which compartment has the cooling problem before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, fan housing, electrical specifications, and pre-attached wire harness configuration of the original WR60X26866 evaporator fan motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR60X10074 Refrigerator Evaporator Fan Motor The XPARTCO WR60X10074 is an aftermarket replacement evaporator fan motor with thermistor for GE and Hotpoint refrigerators. This motor is located at the back of the freezer and circulates air across the evaporator coils, which convert refrigerant into cooling capacity — the fan is what carries that cooled air into both the freezer and fresh food compartments. Bundled with this motor is a separate thermistor that snaps onto the top portion of the evaporator and sends temperature signals back to the main control board, letting it regulate cooling accurately. Rated 9.75V DC, 3.25W — the same base motor used in our WR60X10185 listing, but this version ships with the thermistor included. GE's own guidance is direct on this point: the thermistor should be replaced at the same time as the evaporator fan, since the two are serviced together under this part number rather than sold and swapped independently. Common failure causes include worn motor bearings and general electrical wear. Symptoms include unusual noise from the freezer, a refrigerator or freezer section running too warm, or inconsistent temperatures overall. It directly replaces AP3191003, 914169, 197D4492G001, and 197D2039P013. Quick Answer The XPARTCO WR60X10074 Refrigerator Evaporator Fan Motor fixes GE and Hotpoint refrigerators with unusual noise from the freezer, a refrigerator or freezer section running too warm, or inconsistent cooling overall. 9.75V DC, 3.25W, includes thermistor. Replaces AP3191003, 914169, 197D4492G001, 197D2039P013. This is the motor-plus-thermistor version — if your old connector has no thermistor wire, you need our WR60X10185 listing instead; this is also a different assembly from our WR60X10318 side-by-side listing, which has the thermistor integrated into the motor's own harness rather than as a separate snap-on piece. Common Problems This Part Fixes Unusual noise — humming, buzzing, or grinding — coming from the freezer Fresh food compartment or freezer running too warm Inconsistent or fluctuating refrigerator temperatures Refrigerator running constantly as it struggles to maintain temperature Fan motor that has gone silent after previously running normally Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X10074, 197D4492G001, 914169, AH304658, AP3191003, AGE29122, PD00001062, EA304658, PS304658 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE and Hotpoint refrigerators, including model numbers such as DSS25PFMCCC. Note — check your connector before ordering: This motor includes the thermistor. If your old motor's connector has no thermistor wire — a plain 4-wire harness with 2 empty pin slots on a 6-pin connector — you need our WR60X10185 listing instead (no thermistor). If your connector has a dedicated light connector, you need WR23X10467. This part is also a separate assembly from our WR60X10318 listing, a side-by-side platform motor with the thermistor built directly into its own 6-pin harness rather than snapping onto the evaporator as a separate piece. Even between similar GE thermistor-equipped motors, always verify your full model number, since GE support has confirmed these are not automatically interchangeable without checking your specific model. Contact our support team with your model number if you're unsure which motor your refrigerator needs. Key Features Aftermarket replacement evaporator fan motor — circulates air across the evaporator coils to cool the freezer and fresh food compartments Includes a separate thermistor that snaps onto the top of the evaporator and reports temperature to the main control board Resolves "unusual noise," "running too warm," and "inconsistent cooling" symptoms caused by fan motor or thermistor failure Rated 9.75V DC, 3.25W Direct drop-in replacement matching the original mounting and blade fitment Replaces AP3191003, 914169, 197D4492G001, and 197D2039P013 Compatible with GE and Hotpoint refrigerators Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WR60X10074 OEM Part Number WR60X10074 Part Type Refrigerator Evaporator Fan Motor with Thermistor Condition Aftermarket Replacement Brand GE Location Back of the freezer, over the evaporator coils Voltage 9.75V DC Wattage 3.25 W Includes Thermistor Yes — snaps onto the top of the evaporator, sold together Weight Approx. 0.6 lb. Quantity 1 fan motor + 1 thermistor Compatible Brands GE, Hotpoint Installation Notes ⚠️ Unplug Refrigerator Before Starting — Replace The Thermistor Along With The Motor Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access is through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator coil, fan, and thermistor. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing. Photograph the wiring harness connector, the fan blade's orientation, and the thermistor's snap-on position before disconnecting anything. Unplug the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Unsnap the old thermistor from the top of the evaporator and disconnect its wiring as well. Install both the new motor and the new thermistor together, even if only one of them tested as failed — GE's own guidance is to replace the thermistor whenever the evaporator fan is replaced, since they're serviced as a pair under this part number. Mount the new motor in the same position, reconnect the wiring harness connector, and snap the new thermistor onto the same spot on the evaporator, reconnecting its wiring. Confirm the fan blade spins freely by hand without contacting the housing before reassembling the back panel. Restore power and monitor both compartments over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Do I really need to replace the thermistor if only the fan motor stopped working? GE's official guidance is yes — the thermistor should be replaced along with the evaporator fan whenever this part number is used, since they're sold and serviced together as a pair rather than as fully independent components. That said, some technicians have successfully replaced just the fan motor alone in certain situations; if you want to attempt a fan-only swap, test your existing thermistor first and keep in mind this isn't the manufacturer-recommended approach. How do I know if I need this motor or the WR60X10185 (no thermistor) version? Look at your old motor's electrical connector before ordering. This WR60X10074 motor comes with a thermistor — if your connector has a thermistor wire running to it, this is the correct part. If your connector is a plain 4-wire harness with no thermistor wire and two empty pin positions on a 6-pin plug, you need our WR60X10185 listing instead, which does not include a thermistor. My fridge isn't cooling but the fan seems to spin fine. Could it still be this part? Yes — if the fan is spinning but the fridge still isn't cooling properly, the thermistor half of this assembly is worth suspecting, since a faulty thermistor can send incorrect temperature readings to the control board even while the fan motor itself works fine. One customer confirmed their control board and thermistor initially "checked good" before eventually tracing a similar symptom to fan circulation — so it's worth testing both components rather than assuming the fan alone is the issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the 9.75V, 3.25W motor design, blade fitment, and thermistor function of the original WR60X10074 evaporator fan motor and thermistor used in compatible GE and Hotpoint refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana Product Description Maintain optimal cooling with the Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat. This OEM defrost thermostat is designed for select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators, monitoring evaporator coil temperature to regulate the defrost cycle, preventing frost buildup and ensuring efficient cooling. It addresses issues like frost accumulation, warm refrigerator temperatures, or freezer not cooling properly, delivering reliable performance as an authentic Whirlpool part. Note: Includes one defrost thermostat with two-wire connector. Disconnect power before installation. Check defrost heater and related components for optimal performance. Replaces part numbers: WPW10392132, AP6020798, W10392132, PD00028150, EAP11754118, 2118359, PS11754118. Compatibility: Compatible with models including but not limited to: Whirlpool: ED5FVGXWS00, ED5VHGXMB10, ED5VHGXML10, GD5DHAXVY00, WRS325FDAM02 Kenmore: 106.51132210, 106.51133210, 106.51173310 KitchenAid: KSRJ25FXMS00, KSRL25FXMT00 Maytag: MSD2559XEM01, MFI2569VEM10 Amana: ASD2522WRB02, ASD2522WRW01 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators. ❄️ Specifications: OEM defrost thermostat, two-wire connector. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves frost buildup, warm refrigerator temperatures, or freezer not cooling properly. Product Specification Part Number: Genuine Whirlpool WPW10392132 Component Type: Refrigerator defrost thermostat Material: Metal and plastic with sealed sensor Electrical Specs: 120V compatible Mounting: Clip-mounted on evaporator coil Operating Conditions: Suitable for low-temperature refrigerator environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO WR07X10131 Refrigerator Compressor Overload Relay The XPARTCO WR07X10131 is an aftermarket replacement compressor start relay and overload, a PTCR combination device, for GE, Hotpoint, Kenmore, and RCA refrigerators. It plugs onto the compressor, helps the compressor start by managing the current it draws at startup, and protects it against overload while it runs. When it fails, the compressor may click but not start, and the refrigerator and freezer stop cooling. This is a direct-fit aftermarket replacement for the original GE part. A failed relay is one of several causes of a compressor that won't run, so confirm the symptoms and test the relay before replacing it. Quick Answer The XPARTCO WR07X10131 Compressor Overload Relay fixes a GE, Hotpoint, Kenmore, or RCA refrigerator whose compressor clicks but won't start, or whose refrigerator and freezer have stopped cooling. Classic symptom: you hear a click from the back of the refrigerator every few minutes, the compressor never runs, and both compartments warm up. Common Problems This Part Fixes Refrigerator and freezer have stopped cooling Compressor clicks but doesn't start Compressor won't start at all Compressor cycles on and off or trips repeatedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This relay and overload directly replaces the following part numbers: WR07X10131, WR08X10074, WR08X10089, WR08X10111, 197D6266P001, 5SP14A319NF, WR09X10124, AGE27632, AP4538934, AH2577842, EA2577842, EAP2577842, PD00001415, PS2577842 These numbers span several generations of GE's own part numbering for this relay as refrigerator models were updated. Confirm against your refrigerator's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This relay and overload is listed for GE, Hotpoint, Kenmore, and RCA refrigerators, including these examples: GE CNE22SSEAFSS, GNE22GSEAFSS, PFSF2MIYAWW (bottom-mount) GE CTH17RBT2RWW, GTH18CCEHRWW, GTS18HBSFRWW (top-freezer) GE GSH22JGDBBB, GSL25JFXNLB Note: One retailer lists this part for more than 600 models, so the models above are only a sample. GE's catalog page for the original part carries a warning about use with flammable refrigerants such as R600a, so confirm the part against your refrigerator's model number before installing. Contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket compressor start relay and overload (PTCR combo) Helps the compressor start and protects it against overload Resolves no-cooling and clicking-compressor problems caused by a failed relay Fits many GE, Hotpoint, Kenmore, and RCA refrigerators Easy repair with basic hand tools, typically 15 to 30 minutes Product Specifications Part Number XPWR07X10131 OEM Part Number WR07X10131 Part Type Refrigerator Compressor Start Relay and Overload (PTCR Combo) Condition Aftermarket Replacement Location On the Compressor Application GE, Hotpoint, Kenmore & RCA Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator before beginning, and wear work gloves. Pull the refrigerator out and remove the rear access cover to reach the compressor, then disconnect the wire connector and any retaining clip, and pull the old relay straight off the compressor terminals. Push the new relay on in the same orientation, reattach the clip and connector, and replace the cover. Do not touch or disturb the sealed refrigerant lines. Allow the refrigerator several hours to cool after restoring power. Frequently Asked Questions My refrigerator isn't cooling and the compressor clicks. Is this the part I need? A failed start relay and overload is a common cause of a clicking compressor that won't start. With the refrigerator unplugged, you can test the relay for continuity. A failed compressor or a failed run capacitor can look similar. What does this part do? It helps the compressor start by regulating the current sent to it at startup, and it protects the compressor from overload while it runs. Do I need to open the sealed refrigerant system? No. The relay plugs onto the compressor terminals from the outside, and the refrigerant lines are not touched. Will this fit my refrigerator? It is listed for many GE, Hotpoint, Kenmore, and RCA refrigerators, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

8558953 Dishwasher Touchpad and Control Panel Genuine OEM Fits Specific Kenmore Dishwasher Models Replaces Part Numbers: WP8558953, 8558953, 1066185, 8558928, 8563373, AP6013229, PS11746451.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WH22X38697 Washer Genuine Control Board Fits Specific GE Washer Model Main Control Board Fl Washer Le W/instructions Replaces Part Numbers: WH22X38697, WH22X37837, WH22X36638, WH22X32458, WH22X35518, WH22X30897, WH22X29546, WH22X32058, WH22X34660, WH22X36858, WH22X37838, AP8054699, PS17874598.

Read more less

215846604 Genuine OEM Frigidaire Refrigerator Defrost Timer The 215846604 is a genuine Frigidaire OEM defrost timer, mounted inside the refrigerator near the top of the back wall. This timer is the scheduler for the defrost circuit: on a set cycle, it switches the refrigerator out of normal cooling mode and into a defrost mode, energizing the defrost heater long enough to melt any frost that has accumulated on the evaporator coil, then switches back to cooling once defrost is complete. This cycle repeats automatically for as long as the refrigerator runs, which is why a healthy timer is essential to preventing frost buildup in the first place. Rated 120V with a 6 hour, 21 minute cycle, measuring approximately 1.5"H x 3.2"L x 2.3"W. When this timer fails, the defrost heater never gets the signal — and the electrical energy — it needs to run, so frost keeps accumulating on the coil unchecked. A failing timer typically shows up as heavy frost or ice buildup on the evaporator coil, a freezer that runs too cold or too warm, or a refrigerator section that isn't cooling properly because ice-caked coils can't transfer heat efficiently anymore. It directly replaces AP2592907, 08003824, 08011620, 1748201, 241809401, 241809402, 442754, 5300541134, 5300800692, 5308003824, AH423802, EA423802, PS423802, and CC304. Quick Answer The 215846604 Genuine OEM Frigidaire Refrigerator Defrost Timer fixes Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers with heavy frost or ice buildup on the evaporator coil, a freezer running too warm or too cold, or a refrigerator section not cooling properly. 120V, 6 hour 21 minute defrost cycle. Replaces AP2592907, 08003824, 08011620, 1748201, 241809401, 241809402, 442754, 5300541134, 5300800692, 5308003824, AH423802, EA423802, PS423802, CC304. Before replacing, test the defrost thermostat and defrost heater with a multimeter — if both test good, the timer is the most likely faulty component. Common Problems This Part Fixes Heavy frost or ice buildup on the evaporator coil Freezer compartment running too cold or too warm Refrigerator section not cooling properly Refrigerator or freezer overheating Refrigerator running constantly as ice-caked coils reduce cooling efficiency Frost visible on interior walls or around the back panel Defrost heater not activating on its normal schedule Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost timer directly replaces the following OEM and cross-reference part numbers: 215846604, 08003824, 08011620, 1748201, 241809401, 241809402, 29811-3, 442754, 5300541134, 5300800692, 5308003824, 54113-1, 54113-4, 55448-3, 55448-4, 55467-1, 8003824, AH423802, CC304, EA423802, F111812, G000158274, G000158291, G000173814, G000187005, G000187464, G158274, G163818, G169069, G173814, G174821, G178820, G185160, G187464, K1224661, K1224662, K1226501, K1226502, K1227229, K1227920, K1227927, K1228104, K1228105, K1230354, K1230534, K1233374, K1233375, NR00422503, R000422503, R000900129, R422503, W188C189A06, W188C189A07, WR422503, PD00005279, EAP423802, AP2592907, PS423802. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost timer is compatible with select Frigidaire refrigerators and freezers, and also fits select Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers built on the same Frigidaire/Electrolux platform. Note — not the same as 215846602: This timer runs a 6 hour, 21 minute defrost cycle. A similarly-numbered part, 215846602, runs a different cycle (6 hour, 40 minute) and replaces a separate set of numbers (215846606, 240371001, 241621501, AP2111929, PS423801). The two are not interchangeable. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which timer fits your refrigerator. Key Features Genuine Frigidaire OEM part — factory-specified cycle timing and switch contacts Automatically schedules the refrigerator's transition between cooling and defrost modes 6 hour, 21 minute defrost cycle Resolves "frost buildup on the coil," "freezer too cold or too warm," and "refrigerator not cooling" symptoms caused by timer failure Compact size: approximately 1.5"H x 3.2"L x 2.3"W Direct drop-in replacement — mounts to the original bracket with the same wiring harness connector Replaces AP2592907, 08003824, 08011620, 1748201, 241809401, 241809402, 442754, 5300541134, 5300800692, 5308003824, AH423802, EA423802, PS423802, and CC304 Compatible with Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 215846604 Part Type Refrigerator Defrost Timer Condition Genuine OEM Brand Frigidaire Voltage 120V Defrost Cycle 6 hours, 21 minutes Location Inside the refrigerator, near the top of the back wall Height 1.5 in. Length 3.2 in. Width 2.3 in. Weight Approx. 2.75 oz. Repair Difficulty Easy — basic tools required Quantity 1 defrost timer Compatible Brands Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, Westinghouse Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Locate the defrost timer control inside the refrigerator, typically near the top of the back wall — on some models it may be located behind a rear access panel or near the control housing instead, so check your specific model if it isn't immediately visible. Photograph the wiring harness connector before disconnecting anything. Use a screwdriver to remove the screws securing the timer in place, then carefully disconnect the wiring harness from the back of the old timer. Connect the wiring harness to the new 215846604 timer, matching the original connector orientation, and secure it in place with the mounting screws. Restore power and monitor the refrigerator over the next day to confirm the defrost cycle is running on schedule and frost is no longer accumulating excessively on the coil. Tools needed: screwdriver, work gloves. Frequently Asked Questions How do I know if the timer is actually the problem and not the defrost heater or thermostat? The defrost timer, defrost heater, and defrost thermostat all work together in the same circuit, so it's worth testing the other two before assuming the timer has failed. Test the defrost thermostat and the defrost heater with a multimeter — if both test as functioning properly, it's very likely the timer is the faulty component causing the defrost cycle not to run. There's heavy frost or ice on the coil. Is that definitely the timer? It's one of the most common causes. If the timer fails to advance into the defrost portion of its cycle, the heater never gets the signal or the power it needs to run, so frost keeps accumulating on the evaporator coil with nothing to melt it off. This is exactly the scenario this timer is designed to prevent when it's working correctly. What's the difference between 215846604 and 215846602? These are different timers with different cycle lengths — this 215846604 runs a 6 hour, 21 minute cycle, while 215846602 runs a 6 hour, 40 minute cycle and replaces a separate group of part numbers. They are not interchangeable, so always confirm which specific number your refrigerator's parts diagram calls for before ordering. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original cycle timing, switch contacts, and wiring harness configuration of the defrost timer originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

242253002 Refrigerator Genuine OEM Water Valve Replaces Part Numbers:242253002, 242102201, 2689640, OEM22679498, AP5669874, PS7321353. Description: This Water Inlet Valve is a Genuine OEM part for specific Frigidaire refrigerator models. It is designed to manage the flow of water to the ice maker and water dispenser. This solenoid-operated valve responds to commands from the refrigerator's electronic control, opening to allow water in and closing to stop the flow, ensuring proper operation of both ice production and water dispensing functions.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less