Search results for "washer switch"

WH01X29528 Genuine OEM GE Washer Door Lock The WH01X29528 is a genuine GE OEM door lock assembly for GE front-load washers and select GE Ultrafast 2-in-1 combo washer/dryers. This is a safety mechanism, not just a switch: when the door closes, the lock engages automatically and secures the door shut for the full length of the cycle, only releasing once the control confirms it's safe to open. This prevents the door from being opened mid-cycle, which would otherwise let water and detergent spill out and create both a mess and a safety hazard. Rated 120VAC, 60Hz, 16A. Over time, the door lock can fail from physical damage or ordinary wear, and when it does, the symptoms can be wide-ranging: a washer that won't start because the control never confirms the door is locked, a cycle that stops partway through, a door that won't unlock at the end of a cycle, or in some cases excessive noise and shaking during operation since the lock also plays a role in keeping the door assembly seated correctly. It directly replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, and 0024000128GE. As a genuine OEM part, the WH01X29528 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH01X29528 Genuine OEM GE Washer Door Lock fixes GE front-load washers and GE Ultrafast combo washer/dryers where the door won't lock, the washer won't start, the door pops open or unlocks unexpectedly during the cycle, or the cycle stops partway through. 120VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, 0024000128GE. Before replacing, try a power reset — unplug the washer for 30 seconds and plug it back in — or hold Start/Pause for 15 seconds to command the control to release the lock; either can resolve a door stuck locked without needing a new part. Common Problems This Part Fixes Washer won't start because the door lock never confirms as locked Door lock fails to engage, or the door pops open after locking Door unlocks unexpectedly during the wash cycle Cycle stops or interrupts partway through Door won't unlock at the end of a completed cycle Excessive noise or shaking during operation related to a loose door seal Error code related to the door lock displayed on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, V13305, AGE26402, PD00060769, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock is compatible with select GE front-load washers and GE Ultrafast 2-in-1 combo washer/dryers, including model numbers such as: GFW510SCN0WW, GFW510SCN1WW, GFW510SCN2WW, GFW510SCN3WW, GFW510SCN4WW, GFW510SCN5WW GFW550SPN0DG, GFW550SPN2DG, GFW550SSN1WW GFW650SPN1SN, GFW650SPN2SN, GFW650SSN2WW, GFW650SSN3WW GFW655SSV0WW, GFW655SPV0WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS, GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW, GFW850SSN4WW, GFW850SSN5WW PFQ97HSPV0DS (GE Ultrafast 2-in-1 combo washer/dryer) PFW870SPV0RS, PFW870SSV0WW PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note: Always verify your full model number before ordering, since GE uses several different door lock assemblies across its front-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified locking mechanism and switch design Safety lock that secures the door shut for the full length of the wash cycle Resolves "won't lock," "won't start," "door pops open," and "cycle interruptions" symptoms caused by lock failure Rated 120VAC, 60Hz, 16A Direct drop-in replacement — matches the original mounting and harness connector Replaces AP6985313, EAP12749276, 4958749, PS12749276, PD00060769, ITW 12070-71, V13305, and 0024000128GE Compatible with GE front-load washers and GE Ultrafast 2-in-1 combo washer/dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH01X29528 Part Type Washer Door Lock Assembly Condition Genuine OEM Brand GE Application Front-Load Washers, GE Ultrafast Combo Washer/Dryers Voltage 120VAC Frequency 60 Hz Current Rating 16A Function Locks the door shut during the wash cycle; releases when the control confirms it's safe Quantity 1 door lock assembly Compatible Brand GE Installation Notes ⚠️ Unplug Washer Before Starting — Try A Power Reset First If The Door Is Stuck Locked Before replacing the part, try the simplest fixes first. Unplug the washer, wait 30 seconds, and plug it back in to let the control fully reboot — a simple power reset can release an operational lock and clear the problem without any disassembly. If that doesn't work, try holding the Start/Pause or Power button for 15 seconds to command the control to unlock the door; this doesn't always succeed but is quick to try before opening up the washer. If the door is still locked and you need physical access, never work on the appliance while it's connected to power. Once you've confirmed replacement is necessary, disconnect power at the outlet or shut off the circuit breaker. Wear work gloves. Access is typically from the front, working around the door boot/gasket to reach the lock assembly mounted to the front panel. Photograph the wiring harness connector and mounting position before disconnecting anything. Disconnect the harness connector from the old lock, remove its mounting screws, and pull it free. Install the new WH01X29528 in the same position, secure the mounting screws, and reconnect the harness connector fully. Reseat the door boot/gasket if it was disturbed, restore power, and run a test cycle to confirm the door locks, stays locked through the cycle, and releases normally at the end. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My washer's door is stuck locked. Do I need to replace this part right away? Not necessarily — try the simple resets first. Unplug the washer for 30 seconds and plug it back in to let the control fully reboot, which can release an operational lock on its own. If that doesn't work, try holding the Start/Pause or Power button for 15 seconds, which commands the control to release the lock electronically. These steps resolve many stuck-door situations without needing to replace the lock assembly at all. My washer won't start. Is that this part? It's a strong possibility. The control won't begin a cycle until it receives confirmation that the door is locked, so if this lock has failed and isn't sending that signal, the washer will simply refuse to start even though everything else appears normal. Try the power reset steps above first, then check for a door lock-related error code on the display before assuming the part has failed. I already replaced this lock once and it failed again. What should I check? If a newly replaced lock fails again relatively quickly, it's worth having the washer's control board checked, since a board that's sending incorrect signals to the lock can cause repeat failures that look like the lock itself is bad. It's also worth confirming the door boot/gasket is seated correctly, since a misaligned door can put uneven stress on the lock mechanism. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same locking mechanism, switch design, and harness connector as the door lock originally installed in your GE front-load washer or Ultrafast combo washer/dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC34-00025B Washer Door Lock Replaces Part Numbers: DC34-00025B, AP5799391, PS8763546. Fits Specific Samsung Washer Models DC 12V Description: This Door Lock Switch is essential for maintaining the secure operation of your washer. fits specific Samsung washer models. This replacement part ensures that the door lock mechanism functions correctly, providing peace of mind during every wash cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.  

Read more less

XPARTCO WE04X10052 Dryer Door Switch - Compatible with GE, Hotpoint Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO WE04X10052 Dryer Door Switch. This door switch is designed for select GE and Hotpoint dryers, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WE04X10052, 877374, WE4X10052, EXPWE4X10052, PD00030680, AH265289, EAP265289, EA265289, AP2042951, PS265289. Compatibility: Compatible with models including but not limited to: GE: WSM2420D0CC , WSM2420D0WW , WSM2420D1CC , WSM2420D1WW , WSM2420D2CC , WSM2420D2WW , WSM2420D3WW , WSM2420D4WW , WSM2420D5WW , WSM2420TAAAA , WSM2420TAACC , WSM2420TAAWW , WSM2420TBAAA , WSM2420TBAWW , WSM2480D0WW , WSM2480D1WW , WSM2480D2WW , WSM2480D3WW , WSM2480TAAAA , WSM2480TAAWW , WSM2480TBAAA , WSM2480TBAWW , WSM2480TCAAA , WSM2480TCAWW Hotpoint: HTDP120EDWW, NVLR333EE0WW, HTDX100GDWW Other brands: Select models requiring WE04X10052 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Hotpoint, and other dryers requiring WE04X10052. 🔥 Specifications: replacement dryer door switch, 2- or 3-terminal configuration, push-to-start functionality. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop. Product Specification Part Number: XPWE04X10052 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: 2- or 3-terminal (model-specific, verify before purchase) Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

285805 Genuine OEM Whirlpool Washer Water Inlet Valve The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves. This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517. Quick Answer The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer won't stop filling — overfilling past the normal level Water leaking or dripping from the washer after the cycle has ended No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cycle stalling at the fill step and never advancing to wash Hot water inlet blocked by calcium or mineral deposits after years of hard-water use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including: Whirlpool top-load washers and laundry centers Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Complete kit — includes mounting bracket, screws, and installation instructions Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform Approximately 5.7" tall, metal and plastic construction Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 285805 Part Type Washer Water Inlet Valve Kit Condition Genuine OEM Brand Whirlpool Application Direct-Drive Top-Load Washers / Laundry Centers Kit Contents Water inlet valve, mounting bracket, screws, instructions Ports 2 (hot and cold) Hose Compatibility 1/2" ID Thread Specification Two 3/4"-11 x 1/2" NHT hose threads Height Approx. 5.7 in. Material Metal and plastic Color Blue or green (both correct — varies by production run) Quantity 1 valve kit Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions My valve is blue but the old one was green (or vice versa). Did I get the wrong part? No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance. The new valve's bracket doesn't match my old one. What do I do? This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent. Only hot water won't fill, but cold works fine. Is that this valve? Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled. My washer won't stop filling. Is that dangerous, and is it this valve? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC64-00828B Dryer Door Switch The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open. This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers. Common Problems This Part Fixes Dryer not starting even though the door is closed Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently Error codes dC, dF, dE, or d0 displayed on models with digital displays Dryer continuing to run with the door open (unsafe failure mode — replace immediately) Interior dryer light not turning on when the door is opened Door switch button visibly broken, stuck, or not making the expected click when pressed Multimeter test shows the switch fails to change state when actuated Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including: Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related) Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related) Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related) Samsung dryers — DV5 series (DV50K7500EW and related) Samsung dryers — DVE series (DVE60M9900W and related electric models) Samsung dryers — DVG series (DVG45N5300V and related gas models) Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch that detects whether the dryer door is closed — required for the dryer to start and run Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing Durable plastic housing with metal contacts — withstands frequent door open/close cycles Resolves Samsung door-related error codes including dC, dF, dE, and d0 Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436 Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC64-00828B Also Replaces DC64-00828A (prior version) Part Type Dryer Door Switch (Door Jamb Switch) Condition Aftermarket Replacement Application Electric and Gas Dryers (Samsung platform) Dimensions Approximately 1.73"L x 1.73"W x 0.47"H Color White Material Plastic / Metal Error Codes Resolved dC, dF, dE, d0 (door-related) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What do error codes dC, dF, dE, and d0 mean on Samsung dryers? These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage. My dryer is running with the door open — what should I do? A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer. What is the difference between DC64-00828B and DC64-00828A? These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing. My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch? Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB24X10146 Microwave Door Switch The XPARTCO WB24X10146 is an aftermarket replacement micro switch (also called a door interlock switch) compatible with a wide range of GE, Hotpoint, RCA, Kenmore, and Sears over-the-range and countertop microwaves. This is a "stand on" style normally-open (NO) interlock switch, identified by the internal designation KW3A-NO, that mounts near the door latch and only closes its circuit when the door is fully shut and latched. The control board reads this switch as part of a multi-switch safety interlock chain that confirms the door is secure before allowing the magnetron to energize. When this switch fails, the microwave commonly won't start at all, trips a door-related error code, or in rare cases can allow the unit to run with the door not fully secured — which is a safety-relevant fault, not just a convenience one. It directly replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO WB24X10146 Microwave Door Switch fixes GE, Hotpoint, RCA, and Kenmore/Sears microwaves that won't start, display a door-related error code, or have a door that doesn't reliably confirm as closed. Normally-open (NO) "stand on" interlock switch, rated 250VAC / 16A, with 0.187" (4.7mm) quick-connect terminals. Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Classic symptom: turntable light and display work, but pressing Start does nothing. Common Problems This Part Fixes Microwave won't start when Start is pressed, even though the display and light work Door-related error code or fault light on the display Microwave randomly shuts off mid-cycle Door feels like it isn't latching or registering as closed Clicking sound from the door area with no response from the microwave Intermittent operation that seems tied to how hard the door is closed ⚠ Safety-Relevant Component Door interlock switches are safety components that prevent the magnetron from energizing unless the door is fully closed and latched. Never bypass, jumper, or defeat a microwave door switch to "get it working" — doing so can allow microwave energy to leak while the door is open, which is a genuine radiation safety hazard. Always disconnect power before servicing, and replace all interlock switches in the chain if more than one shows signs of wear. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with a wide range of GE-built microwaves across the following brands: GE over-the-range and countertop microwaves (JVM, PVM, and CEB series, including JEM3072DH1BB, JEM3072SH1SS, JNM3161DF2BB, and CCWK15C1W1DS/SS) Hotpoint microwaves (GE-built models) RCA microwaves (GE-built models) Kenmore and Sears microwaves (select GE-built models) Note: Do not confuse this with the similarly styled EXP499/EXP497 microwave door switches, which also use 4.7mm terminals but are not the same switch. WB24X10146 is a "stand on" style switch specific to GE's own interlock design — always match by part number, not terminal size alone. Always verify your appliance model number before ordering. Key Features Normally-open (NO) "stand on" door interlock switch, internal designation KW3A-NO Resolves "won't start," "door error code," and "shuts off mid-cycle" symptoms caused by interlock switch failure Rated 250VAC / 16A for reliable switching under microwave load 0.187" (4.7mm) quick-connect terminals for a secure wire connection Direct-fit mounting to match the original interlock bracket Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 Compatible with GE, Hotpoint, RCA, Kenmore, and Sears microwaves across dozens of models Aftermarket replacement built to OEM-equivalent quality and safety standards Product Specifications Part Number XPWB24X10146 OEM Part Number WB24X10146 Part Type Microwave Door Interlock Switch ("Stand On" / KW3A-NO) Condition Aftermarket Replacement Switch Type Normally Open (NO) Voltage Rating 250VAC Current Rating 16A Terminal Width 0.187" (4.7mm) Compatible Brands GE, Hotpoint, RCA, Kenmore, Sears Installation Notes ⚠️ Unplug Microwave Before Starting Disconnect power at the outlet, and for built-in/over-the-range units also switch off the dedicated circuit breaker — microwaves store high voltage in the capacitor even after unplugging. Remove the outer cabinet or control panel cover to access the door switch assembly near the latch mechanism. Photograph the wiring before disconnecting, since GE microwaves typically use two or three interlock switches wired in sequence and mixing up the connections can leave the unit unsafe to operate. Disconnect the quick-connect terminals from the old switch, noting which wire goes to which terminal. Remove the mounting screw(s) holding the switch to its bracket and remove the old switch. Install the new WB24X10146 in the same position and secure it with the mounting screw(s). Reconnect the terminals exactly as photographed. Reassemble the cabinet or panel, restore power, and test that the door registers correctly and the microwave starts normally. Tools needed: Phillips screwdriver, nut driver (for cabinet screws). Frequently Asked Questions My microwave's display and turntable light work, but it won't start — is this the part? This is a classic symptom of a failed door interlock switch. The control board needs a confirmed "door closed and latched" signal from all switches in the interlock chain before it will energize the magnetron. If that signal is missing from even one switch, most GE microwaves will power up normally but refuse to start a cook cycle. Confirm with a multimeter continuity test on the suspect switch before ordering, since GE microwaves usually use more than one interlock switch. Is this the same as the EXP499 or EXP497 microwave door switch? No — while all three use similar 4.7mm terminals, they are different switches used in different microwave platforms and are not interchangeable. WB24X10146 is GE's own "stand on" KW3A-NO design. Always match by part number rather than terminal size or general appearance. Is it safe to keep using the microwave if I suspect this switch is bad? We'd recommend not continuing to use it until it's repaired. Door interlock switches exist specifically to prevent microwave energy from leaking out while the door is open or not fully latched. If a switch is failing intermittently, the microwave may seem to work sometimes, but that's not a reason to keep using it — replace the switch before further use, and never attempt to bypass or jumper an interlock switch. How many interlock switches does my GE microwave have, and do I need to replace them all? Most GE microwaves use two or three interlock switches wired in sequence (often a primary switch, a secondary/monitor switch, and sometimes a door sensing switch). You typically only need to replace the specific switch that's testing bad, but if one has failed from age or wear, the others are often not far behind — some technicians replace the full set at once to avoid a repeat repair call. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406108 Dryer Door Switch - Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO 3406108 Dryer Door Switch. This door switch is designed for select Whirlpool, Kenmore, Maytag, and other dryer models, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch with 2 wire leads and a two-prong plug. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP3406108, 3406108, PD00029356, EAP11741702, PS11741702, AP6008562.  Compatibility: Compatible with models including but not limited to: Whirlpool: LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. Kenmore: 11060012000, 11060022010, 11060232000 Maytag: MEDC400VW0, AED4475TQ1 Other brands: Select models requiring 3406108 (e.g., Amana, Crosley, Roper) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Roper dryers requiring 3406108. 🔥 Specifications: Replacement dryer door switch, 2 wire leads, two-prong plug, 120-240V, 50-60Hz, 11A, 1/3HP. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop when door is opened. Product Specification Part Number: XP3406108 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: Two-prong plug with 2 wire leads Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO W10913953 Washer Shift Actuator The XPARTCO W10913953 is an aftermarket replacement washer shift actuator assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper top-load washers with VM (variable motor) transmissions — including Whirlpool Cabrio, Maytag Centennial, and Maytag Bravos series. The shift actuator is a small synchronous gearmotor assembly located beneath the washer tub that controls how the transmission shifts between agitation mode and spin mode during the wash cycle. It moves the arm on the cam ring assembly to engage the basket (for spinning) or disengage it and engage only the agitator or wash plate (for agitation). The shift actuator also contains an internal tachometer that continuously reports the basket's rotational speed to the control board. When the shift actuator fails — most commonly due to a stripped or broken gear inside the gearmotor — the washer may not agitate, not spin, get stuck in one phase of the cycle, display error codes F7E1 or F7E5, or produce a loud grinding or clicking noise as the gears fail. This 6-pin plug assembly is rated 120V, 60Hz, 4W with a synchronous motor running at 3 RPM clockwise rotation. It measures 4-1/4"L x 2-3/4"W x 1-7/8"H and directly replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, 50SM21-1-221B, AP6037270, and PS11769864. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10913953 Washer Shift Actuator fixes Whirlpool Cabrio, Maytag Centennial, and Maytag Bravos top-load washers that won't agitate, won't spin, display error codes F7E1 or F7E5, or make grinding/clicking noises when trying to shift cycles. 6-pin plug, 120V/60Hz/4W synchronous motor, 3 RPM CW, 4-1/4"L x 2-3/4"W x 1-7/8"H. Replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, AP6037270, PS11769864. Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper VM-transmission top-load washers. Common Problems This Part Fixes Washer not agitating — basket fills with water but agitator or wash plate does not move Washer not spinning — cycle advances to spin but basket does not rotate Washer getting stuck in one phase — completing wash or fill but not advancing to spin Clothes soaking wet after a full cycle — washer is not reaching high-speed spin Error codes F7E1 or F7E5 displayed — motor shift or basket speed sensing fault Loud grinding, clicking, or buzzing noise during cycle transitions between agitate and spin Washer pumping normally but basket not spinning after draining Replaces Part Numbers This shift actuator directly replaces the following OEM and cross-reference part numbers: W10913953, W10815026, 4455082, 49TYZ-E120A1, 50SM21-1-221B, KT-155867_rev011, EAP11769864, AP6037270, AWP42172, PD00032232, PS11769864. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shift actuator is compatible with select top-load washers with VM transmissions from the following brands and series: Whirlpool top-load washers — Cabrio series (WTW5000, WTW4816, WTW4850, WTW4915, WTW4950, WTW4955 and related models) Maytag top-load washers — Centennial series (MVWC215, MVWC415, MVWC416, MVWC465, MVWC555, MVWC565 and related models) Maytag top-load washers — Bravos series (MVWX655 and related models) Kenmore / Sears top-load washers (select Whirlpool-built models) Amana top-load washers — NTW series (NTW4516, NTW4655 and related models) Crosley top-load washers (select models) Inglis top-load washers (select models) Roper top-load washers (select models) Note: The W10913953 is for VM (variable motor) transmission top-load washers. It is not compatible with older Whirlpool top-load washers using a different transmission type. Always verify your model number before ordering. The shift actuator works in conjunction with the pulley clutch kit (W10721967 / W10006384) — if the actuator is good but the issue persists, the clutch kit should also be inspected. Key Features Controls transmission shifting between agitation mode and spin mode during the wash cycle Moves the cam ring arm to engage the basket for spinning, or disengage it to allow only the agitator/wash plate to move Integrated tachometer — continuously reports basket rotational speed to the control board for cycle management Synchronous gearmotor — 120V, 60Hz, 4W, 3 RPM clockwise rotation 6-pin plug connector — direct plug-in installation on compatible models Dimensions: 4-1/4"L x 2-3/4"W x 1-7/8"H Resolves F7E1 and F7E5 error codes on compatible Whirlpool and Maytag top-load washers Replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, and AP6037270 Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos, Amana NTW, and Kenmore VM-transmission top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10913953 Also Replaces W10815026, W10597177 (prior versions) Part Type Washer Shift Actuator Assembly (Mode Shift Actuator) Condition Aftermarket Replacement Application Top-Load Washers with VM Transmission (Cabrio, Centennial, Bravos) Motor Type Synchronous gearmotor Voltage 120V AC Frequency 60 Hz Wattage 4W Speed 3 RPM, clockwise rotation Connector 6-pin plug Dimensions 4-1/4"L x 2-3/4"W x 1-7/8"H Includes Integrated tachometer for basket speed sensing Error Codes Resolved F7E1, F7E5 Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. The shift actuator is located beneath the washer tub on the drive shaft assembly. To access it, remove the washer cabinet by unscrewing the top panel and releasing the front panel, or lay the washer on its back if your model requires it. The shift actuator is mounted to the bottom of the drive shaft assembly with mounting screws and connects to the washer's control harness via a 6-pin plug. Photograph the wiring before disconnecting. Remove the mounting screws, disconnect the 6-pin harness, and slide the old actuator off the shaft. Install the new W10913953 actuator in the same position and orientation, secure the mounting screws, and reconnect the 6-pin harness. Reassemble the cabinet, restore power and water, and run a test cycle through both agitation and spin to confirm normal operation. Note: if grinding noise continues after replacing the actuator, inspect the pulley clutch kit (W10721967 / W10006384) for wear. Tools needed: Phillips screwdriver, 1/4" nut driver, Torx screwdriver (T20 on some models). Frequently Asked Questions What does the shift actuator do in a top-load washer? The shift actuator is a small synchronous gearmotor that controls the transmission shifting in Whirlpool Cabrio, Maytag Centennial, and Bravos-style VM-transmission top-load washers. During a wash cycle, the control board signals the actuator to move the cam ring arm — this engages or disengages the drive connection between the motor and the basket. When the cam moves one way, only the agitator or wash plate moves (agitation mode). When it moves the other way, the basket engages and spins at high speed (spin mode). The actuator also contains a tachometer that tells the control board how fast the basket is rotating, which the board uses to manage spin speed and detect imbalance. What are error codes F7E1 and F7E5? On compatible Whirlpool Cabrio and Maytag Centennial/Bravos top-load washers, F7E1 indicates a motor shift error — the actuator failed to complete the shift between agitate and spin mode within the expected time. F7E5 indicates a basket speed sensing fault — the tachometer inside the actuator is not providing a valid speed signal to the control board. Both codes are commonly caused by a failed shift actuator, though a failed drive motor, clutch assembly, or control board can also produce these codes. Replacing the shift actuator resolves both error codes in most cases. Should I also check the pulley clutch kit? Yes — if the shift actuator is replaced but the grinding noise persists, or if the washer still does not agitate or spin properly after the new actuator is installed, inspect the pulley clutch kit (W10721967 / W10006384). The clutch kit is a separate assembly that works in conjunction with the shift actuator to engage the drum. A worn or stripped clutch can produce the same symptoms as a failed actuator and is a common companion failure. Since the washer is already disassembled to replace the actuator, it is a good opportunity to inspect the clutch for wear. What is the difference between W10913953 and W10815026? The W10815026 was an earlier version of this shift actuator, and the W10913953 is the updated current replacement. Both are the same functional component — Whirlpool updated the part number during a production revision. The W10597177 and WPW10597177 are also cross-references for this same actuator. If your washer's parts diagram shows any of these older numbers, the W10913953 is the correct current replacement to order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a synchronous gearmotor and ABS housing to match the electrical specifications and dimensions of the original W10913953 shift actuator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11248040 Washer Console (Control Panel Housing) Genuine Whirlpool part Replaces Part Number W11248040, 4845509, W11035013, W11120176, W11192407, PD00087512, EAP12584120, AP6783239, PS12584120. Model Cross Reference This part #W11248040 works with all models listed. Kenmore / Sears 110.27132412 Washer Kenmore / Sears 110.27132413 Washer  

Read more less

XPARTCO EXP497 Microwave Door Switch (Normally Open) The XPARTCO EXP497 is an aftermarket replacement Normally Open (NO) microwave door interlock switch compatible with a wide range of GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, and Sharp microwaves. The door interlock switch is one of several safety switches in the microwave door system. It allows the microwave to operate only when the door is fully closed — when the door closes, the switch is mechanically activated, completing the circuit and signaling the control board that it's safe for the magnetron to fire. When the door is open, the switch is released and the circuit is broken, preventing the microwave from generating microwave radiation. This switch is rated for 16A at 125/250V AC, giving it the heavy-load capacity required for microwave door safety circuits. It directly replaces an extensive list of cross-reference part numbers from multiple manufacturers, including 3B73362F, SZM-V16-FA-63, WB24X816, WB24X829, WB24X10180, 6600W1K003C, WP56001036, 5304408938, AP4437957, PS3522738, and dozens more. Important: confirm your original switch is a Normally Open (NO) type before ordering — this part will not replace Normally Closed (NC) or COM-style switches. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO EXP497 Microwave Door Switch (Normally Open) fixes microwaves that won't start, won't heat, stop mid-cycle, or won't shut off when the door opens. Universal-fit Normally Open (NO) interlock switch, 16A at 125/250V AC. Replaces 3B73362F, SZM-V16-FA-63, WB24X816, WB24X829, WB24X10180, 6600W1K003C, WP56001036, 5304408938, AP4437957, PS3522738 (and many more). Compatible with GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, and Sharp microwaves. Important: confirm your original switch is "Normally Open" before ordering. Common Problems This Part Fixes Microwave won't start when the door is closed and the start button is pressed Microwave runs but produces no heat — turntable spins, light works, but food doesn't warm Microwave starts and then immediately stops mid-cycle Microwave continues running with the door open (unsafe failure mode — replace immediately) Intermittent start failure — works sometimes, doesn't work other times Door switch button visibly stuck, broken, or fails to click when pressed Multimeter continuity test on the switch shows it doesn't change state when actuated Replaces Part Numbers This Normally Open microwave door switch directly replaces an extensive list of OEM and cross-reference part numbers: 3B73362F, 3B73362E, 6600W1K003D, 6600W1K004C, 6600W1K004F, AH3522738, EA3522738, AP4437957, PS3522738, WB24X816, WB24X0816, AP2024324, QSWMA085WRE0, QSWMA168WRZZ, WB24X10180, AH2370055, EA2370055, AP4484237, PS2370055, 00606693, 00415824, 1386418, 35-00-780, 415824, 606693, AH3477005, EA3477005, PS3477005, AP4070531, PS8726630, 00633795, 00415825, 35-00-781, 415825, 4162223, AP5952985, PS10060855, WB23X10019, 1810578, AH3486591, EA3486591, AP4980343, PS3486591, WB24X10204, WB24X10148, WB24X28940, 251201600929, 3025958, AP5790848, PS8754454, 5304408938, 5304430284, 639405, AH471434, EA471434, AP2151217, PS471434, WB24X10047, WB24X10029, WB24X0815, WB24X10072, WB24X10113, WB24X815, AH237015, EA237015, AP2622452, PS237015, 5304408938, 5304430284, 639405, AH471434, EA471434, AP2151217, PS471434, 5304423463, 892734, AH472733, EA472733, AP2151744, PS472733, 5304493153, 5304440026, 3018427, 5303319558, 5304467694, 75304440026, 75304467694, AP5804011, PS8769124, WB24X10139 1086028, AH953555, EA953555, PS953555, AP3792702, WB24X10140 AH953556, EA953556, AP3792654, PS953556, WB24X829, WB24X10038, WB24X368, WB24X384, WB24X414, WB24X426, WB24X439, WB24X441, WB24X445, WB24X796, WB24X5228, WB24X796, AP2024337, AH237421, EA237421, PS237421, WP56001036, 56001036, 0053464, R0654097, AP6009674, PS11742843, 3405-001034, 3405-000178, 111698, 2028597, AP4044834, PS4131192, WB24X823, WB24X0820, WB24X0823, WB24X820, AH237415, EA237415, AP2024331, PS237415, 5304509460, 5304520020, 5304464099, 4583656, AP6230615, PS12071303, WB24X28941, AH1019163, EA1019163, MW-7100-33, AP3866977, PS1019163, 5304493153, 5304440026, 3018427, 5303319558, 5304467694, 75304440026, 75304467694, AP5804011, PS8769124, D3V-16G-3C25, SZM-V16-FA63. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This Normally Open door switch is compatible with select microwaves from a wide range of brands: GE microwaves (countertop, over-the-range, and built-in models) Whirlpool microwaves Samsung microwaves LG microwaves — MV, LMV, LMH, MQ, MS, LMA, LMVM series (MV1560M, MV1310W, MV1560T, LMV1625B, LMA2112WT, MS1443ASV, LMH1017CVST and many more) Frigidaire microwaves Kenmore / Sears microwaves (multi-brand built models) Panasonic microwaves Sharp microwaves Bosch microwaves (select models — cross-references 00606693, 00633795) Important — Confirm Switch Type Before Ordering: This is a Normally Open (NO) switch. Microwaves typically use 2–3 door switches: one Normally Open and one or two Normally Closed/COM. They are not interchangeable. Inspect your original switch's markings or test it with a multimeter before ordering — if your failed switch is Normally Closed, you need the EXP499 instead. If you're unsure, contact our support team with your microwave model number. Key Features Normally Open (NO) microwave door interlock switch — closes the circuit when the door is closed, allowing the microwave to operate Rated 16A at 125/250V AC — heavy-duty capacity for microwave door safety circuits Universal fit — replaces door switches from GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, Sharp, and Bosch Replaces 50+ OEM and aftermarket cross-reference part numbers across multiple appliance brands Common alternate part numbers include 3B73362F, SZM-V16-FA-63, D3V-16G-3C25, AP4437957, and PS3522738 Important: verify your switch is Normally Open before ordering — NOT a replacement for Normally Closed (use EXP499) or COM-style switches Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number EXP497 Part Type Microwave Door Interlock Switch (Normally Open) Condition Aftermarket Replacement Application Microwaves (cross-brand) Switch Type Normally Open (NO) Max Current 16A Voltage Rating 125/250V AC Common OEM Equivalents 3B73362F, SZM-V16-FA-63, D3V-16G-3C25 Compatible Brands GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, Sharp, Bosch Installation Notes ⚠️ High-Voltage Safety Warning — Microwave Capacitor Microwaves contain a high-voltage capacitor that can hold a lethal electrical charge even after the appliance is unplugged. Before opening the microwave cabinet to access the door switches, always unplug the unit and discharge the high-voltage capacitor using proper safety procedure (with an insulated screwdriver across the capacitor terminals while wearing insulated gloves). If you are not familiar with safely discharging a microwave capacitor, have this repair done by a qualified technician. ⚠️ Wear Work Gloves — Identify Switch Position Before Removing Disconnect power before beginning. Wear work gloves to protect your hands. After safely discharging the high-voltage capacitor, remove the microwave's outer cabinet or control panel as needed to access the door interlock switch assembly — typically located behind the right side of the door frame on most microwaves. Take a photo of all switch positions and wire connections before disconnecting anything. Microwaves usually have 2–3 switches in the door interlock assembly: confirm which one is the Normally Open switch (the EXP497 fits this position only). Disconnect the wires from the old switch — make a note of which wire goes where. Release the switch from its mounting tabs and pull it free. Install the new EXP497 in the same position with the same wire connections. Reassemble the cabinet, restore power, and test the microwave by closing the door and confirming it starts and heats normally, then opening the door and confirming it shuts off immediately. Tools needed: Phillips screwdriver, work gloves, insulated tools (for capacitor discharge). Frequently Asked Questions What's the difference between a Normally Open and Normally Closed microwave door switch? Microwave door interlock systems use both types together to provide redundant safety. A Normally Open (NO) switch — like the EXP497 — has open contacts at rest; when the door closes and pushes the switch button, the contacts close to complete a circuit, signaling "door closed." A Normally Closed (NC) switch is the opposite — contacts are closed at rest and open when the door pushes the button. Most microwaves use one or more of each type wired together so the control system can confirm the door is genuinely closed from multiple inputs. They are not interchangeable — you must replace each switch with the same type. If your switch is NC, order the EXP499 instead. How do I know if I need the Normally Open or Normally Closed switch? The easiest way is to read the part number printed on the side of the failed switch and compare it to the cross-reference lists for the EXP497 (Normally Open) versus the EXP499 (Normally Closed). If the markings are unreadable, you can also test the switch with a multimeter set to continuity mode: with the switch at rest (button released), a Normally Open switch reads open (no continuity) and a Normally Closed switch reads closed (continuity). Replacing each switch with the same type is essential — installing the wrong type can prevent the microwave from starting or create unsafe conditions. My microwave runs but doesn't heat — could this be the door switch? Yes — this is one of the most recognizable symptoms of a failed door switch in a multi-switch interlock system. A microwave that turns on (light, fan, turntable) but does not heat often has a failed door switch in one of the door positions while the others continue to work. The control system may allow the auxiliary components to run but blocks the magnetron from firing without confirmation from all switches. Check all door switches systematically — one Amazon review noted a customer needed three identical switches to fully repair their microwave because the third switch (at the top of the door) was the actual cause of the no-heat condition. Replacing all door switches together is a common approach. My microwave keeps running with the door open — what should I do? This is a serious safety concern. Disconnect power to the microwave immediately and do not use it until the door switch is replaced. A microwave that continues to run with the door open exposes you to microwave radiation, which can cause serious injury. This usually indicates one or more door switches are stuck in the "door closed" position. Replace the failed switches with matching NO or NC type (EXP497 for NO, EXP499 for NC) before using the microwave again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a manufacturer-branded OEM switch from any single brand, but is manufactured to match the dimensions, contact configuration, and 16A/125-250V AC rating of the dozens of OEM door switches it cross-references across multiple appliance brands. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 131763302 Washer Door Striker The XPARTCO 131763302 is an aftermarket replacement washer door striker compatible with a wide range of Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers — including the Frigidaire Affinity series and a broad set of GLTF, FAFW, FFFW, FFFS, ATF, ATFB, BLTF, CTF, CRTF, FCCW, FRFW, FTF, and FWFB models. The door striker (also called a door strike or door catch) attaches to the inside edge of the washer door and physically enters the lock mechanism on the front panel when the door closes. Once engaged, the strike is what the lock latches onto — and the strike also activates the door switch, signaling the control board that the door is safely closed and the washer can start. When the striker fails — typically by cracking, chipping, or breaking off from repeated door closures — the washer will not start, will not lock the door, may leak water, or may fail to advance past the fill phase. Gray/red plastic construction, approximately 2.6" x 1.3". This is the current production part number that supersedes many earlier revisions. It directly replaces 131763302, 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640, 1032664, 1564512, LP3310, PA66-GF25, WH10X10004, AP3580441, AP4508273, AH2378364, AH890617, EA2378364, EA890617, PD00000164, PS2378364, and PS890617. Often replaced together with the matching door lock assembly (131763256, sold separately). Installs in under 5 minutes — no tools required beyond a Phillips screwdriver. Quick Answer The XPARTCO 131763302 Washer Door Striker fixes Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers where the door won't lock, won't start, won't close properly, leaks water, or won't fill. Gray/red plastic. Approx 2.6" x 1.3". Current production part — supersedes 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640, 1032664, 1564512, LP3310, PA66-GF25, WH10X10004, AP3580441, AP4508273, AH890617, EA890617, PS890617, AH2378364, PS2378364. Often paired with the door lock assembly (131763256, sold separately). Common Problems This Part Fixes Washer door won't latch properly — striker broken or worn down Washer won't start because the door isn't detected as locked Washer door won't close — striker missing or damaged Washer door will not open at the end of the cycle — striker stuck inside the lock Washer pumps but won't spin — spin cycle blocked by broken striker Washer won't fill with water — fill cycle blocked by broken striker Water leaking around the door — door not fully sealing because striker isn't fully engaging Striker visibly broken, chipped, or missing on the inside edge of the door Door lock failure — actuator damaged Replaces Part Numbers This washer door striker directly replaces the following OEM and cross-reference part numbers: 131763302, 134456600, 131763300, 131763340, 134456602, 134456640, 1564512, AH2378364, EA2378364, EAP2378364, AP4508273, AFR14210, PD00000391, PS2378364. 131763302 is the current OEM production part superseding all listed earlier revisions. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door striker is compatible with select front-load washers from the following brands: Frigidaire front-load washers — Affinity series (FAFW3001LW0-LW7, FAFW3511KW0-KW2, FAFW3801LW0/LW2/LW3/LW4/LW5, FAFW3921NW0/NW1, FAFW4011LW0, FAFW4221LW0) Frigidaire front-load washers — ATF6000ES0/ES1, ATF6000FS0/FS1/FS2, ATFB6000ES0/ES1, ATFB6000FS0, ATF7000FE0, ATFB7000ES0 series Frigidaire front-load washers — BLTF2940ES0-ES3, BLTF2940FS0/FS1, BLTF6100FS0 series Frigidaire front-load washers — FFFS5115PW0, FFFW4000QW0, FFFW5000QW0 series Frigidaire front-load washers — FRFW3700LW0, FCCW2000LS0, FCCW3000ES0/FS0/FS1/FS2/FS3/FS4 series Frigidaire front-load washers — FTF1040AS0, FTF1240FS0/FS1, BTF2140FS1, CRTF1240AS0, CRTR9300AS0, CTF140ES0, CTF140FS0/FS1/FS2 series Frigidaire front-load washers — GLTF1040/GLTF1240/GLTF1570/GLTF2940 series and related GLEH/GLGH models Frigidaire front-load washers — Additional 38712, 38802, 970L48022A0, 970L48422E0 and related legacy models Electrolux front-load washers — select models with the matching striker configuration Kenmore / Sears front-load washers — 4124182300/2301, 412180/181/182/183/184, 4129042992, 4129052991, 410032990, 410042990, 410052990, 4101400, 410410, 410411 and related Frigidaire-built models Crosley front-load washers — BTF1240ES0/ES1, BTF1240FS0 and related models Gibson front-load washers — select models Kelvinator, Tappan, Westinghouse front-load washers — select models Note: The door striker (131763302) and the door lock assembly (131763256) are two separate components that work together — the striker enters the lock, and the lock grips the striker. If both are worn or one has caused damage to the other, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new part. Always verify your model number before ordering. Key Features Washer door striker — mounts to the inside edge of the door and enters the lock mechanism when the door closes Activates the door switch to signal the control board that the door is safely closed and ready for the wash cycle Restores the proper engagement between the door and lock assembly for consistent locking every cycle Current OEM production part number — supersedes many earlier revisions (131763310, 131763300, 131763340, 134456600, and more) Gray and red plastic construction, approximately 2.6" x 1.3" Replaces 20+ OEM and cross-reference part numbers spanning Frigidaire, Electrolux, GE (WH10X10004), and universal aftermarket catalogs Compatible with Frigidaire Affinity series and a broad set of Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers Often replaced together with the matching door lock assembly (131763256, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 5 minutes with a Phillips screwdriver Product Specifications Part Number XP131763302 Supersedes 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640 Part Type Washer Door Striker (Door Strike / Door Catch) Condition Aftermarket Replacement Application Front-Load Washers (Frigidaire platform) Dimensions Approximately 2.6" x 1.3" Color Gray / Red Material Plastic Mounting Location Inside edge of washer door Often Paired With Door Lock Assembly (131763256, sold separately) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Washer Before Starting — Quick Toolless Replacement Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, use a putty knife to release the manual override latch through the bottom service opening. Locate the old door striker on the inside edge of the washer door. It's typically secured by a single Phillips screw. Unscrew the mounting screw and remove the old striker. If the striker has broken off inside the lock mechanism on the front panel, remove any broken pieces from the lock before proceeding — leaving debris in the lock will damage the new striker and prevent proper engagement. Take the new 131763302 striker and align it with the mounting hole in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Secure the new striker with the Phillips mounting screw. Close the door and confirm the striker enters the lock slot smoothly. Restore power and run a test cycle to confirm the door locks properly and the washer starts. Tools needed: Phillips screwdriver, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door striker and the door lock assembly? These are two separate parts that work together as a system to lock the washer door. The door striker (131763302) is the plastic part attached to the inside edge of the washer door — when the door closes, the striker enters the lock. The door lock assembly (131763256) is the assembly mounted on the front panel just inside the door opening — it contains the latching mechanism that grips the striker and the electrical switch that tells the control board the door is closed. If the striker is broken, the lock has nothing to grip and the washer won't start. If the lock is broken, the striker can still enter the slot but the lock won't hold it or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. What is the difference between 131763302 and the older 131763310 or 131763300? All are the same door striker across production revisions. 131763300 was the original OEM part number, 131763310 and 131763340 were mid-generation revisions, and 131763302 is the current OEM production version. Frigidaire also uses 134456600, 134456602, and 134456640 as additional catalog references for the same part. All are physically and functionally interchangeable — if your washer's parts diagram shows any of these numbers, the 131763302 is the correct current replacement, and this listing covers all of them. My washer won't start and the door seems to close normally — could this be the striker? Yes, this is one of the most common symptoms of a failed door striker on Frigidaire-platform front-load washers. Even though the door appears to close, if the striker has cracked or worn down, it may not physically engage the lock or activate the door switch correctly. Visually inspect the striker on the inside edge of the door — if it's broken, missing, chipped, or its tab has worn down, replacement is straightforward. Also inspect the lock opening on the front panel: if there are broken plastic pieces inside from the old striker, they need to be removed before the new striker can seat properly. Do I really only need a Phillips screwdriver for this repair? Correct — the 131763302 striker is held in place by a single Phillips mounting screw on the inside edge of the washer door. Remove the old striker, install the new one in the same orientation, and tighten the screw. The whole replacement typically takes under 5 minutes once you have the new part in hand. Just make sure to install it in the correct direction — installing the striker backwards will prevent the lock from engaging when the door closes. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable plastic to match the dimensions (approximately 2.6" x 1.3"), mounting configuration, and lock-engagement function of the original 131763302 door striker used in compatible Frigidaire, Electrolux, Kenmore, Crosley, and related front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less