Search results for "washer switch"

XPARTCO MFG63099101 Washer Door Strike (Door Lock Hook) The XPARTCO MFG63099101 is an aftermarket replacement washer door strike — also called a door lock hook or door latch hook — compatible with a wide range of LG front-load washers and Kenmore 796-series washing machines. The door strike is the metal hook component mounted on the inside edge of the washer door. When the door closes, the hook enters the door lock switch on the front panel and engages the electromagnetic lock mechanism, signaling the control board that the door is closed and locking it for safe operation during wash and spin cycles. Without an intact door strike, the lock can't grip anything, and the washer will not start. When the strike breaks — typically from repeated use, sudden impact, or stress over thousands of door cycles — the washer will not start, may stop mid-cycle, may display DE1 or DE2 error codes, leak water around the door, or fail to lock altogether. It directly replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132. Important: replacing the strike requires removing the inside door panel to access the hook — note that the inner glass insert is loose during disassembly and must be handled carefully. Often replaced alongside the matching door lock switch (EBF61315802, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO MFG63099101 Washer Door Strike fixes LG and Kenmore 796-series front-load washers where the door won't lock, won't start, stops mid-cycle, displays DE1 or DE2 errors, or leaks at the door. Metal hook attaches to the inside of the washer door — engages the lock switch when the door closes. Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132. Often paired with the door lock switch (EBF61315802, sold separately). Common Problems This Part Fixes Washer door not latching properly — strike broken or worn down Washer not starting because the door isn't detected as locked Washer stopping mid-cycle due to a door fault DE1 or DE2 error codes displayed on the control panel Minor water drips or leaks around the door during operation — door not sealing because the strike isn't fully engaging Door strike visibly broken, chipped, or missing on the inside edge of the door Door not staying closed — strike worn from repeated impact Washer not powering on Replaces Part Numbers This washer door strike directly replaces the following OEM and cross-reference part numbers: MFG63099101, 2759645, AGF77417823, PD00046132, EAP8752721, AP5787149, PS8752721. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the number printed on your original door hook may be a production batch code rather than the OEM part number — this does not affect fit. Compatibility This door strike is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3170CW/00, WM3180CW series LG front-load washers — WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HVA/01, WM3370HWA, WM3370HWA/01, WM3370HWA/00 series LG front-load washers — WM3400CW, WM3500CW, WM3500CW/00, WM3555HWA, WM3555HWA/00 series LG front-load washers — WM3570HVA, WM3570HVA/00, WM3575CW series LG front-load washers — WM3600HVA, WM3600HWA, WM3600HWA/00, WM3670HRA, WM3670HRA/00, WM3670HVA, WM3670HWA series LG front-load washers — WM3700HVA, WM3700HWA, WM3770HVA, WM3770HWA series LG front-load washers — WM3900HBA, WM3900HWA series LG front-load washers — WM4000HBA, WM4000HWA, WM4270HVA, WM4270HVA/00, WM4370HKA, WM4370HWA series Kenmore / Sears washers — 796-series (79641162410, 79641162411, 79641262610, 79641283310, 79641283311, 79641302610, 79641303610, 79641382410, 79641382411, 79641383410, 79641383411, 79641482410, 79641482411, 79641483410, 79641483411, 79641582410, 79641582411, 79641583211, 79641583410, 79641583411, 79641962610, 79641963610 and many related models) Note: If both the door strike (MFG63099101) and the door lock switch (EBF61315802) have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new strike. Always verify your model number before ordering. Key Features Metal door strike (door lock hook) — mounts to the inside edge of the washer door and engages the door lock switch when the door closes Resolves DE1 and DE2 error codes when caused by a broken door strike on compatible LG and Kenmore washers Restores the proper engagement between the door and latch assembly for a firm, consistent connection every cycle Durable metal construction — designed to withstand repeated opening and closing impact Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132 Compatible with LG WM1388, WM3050, WM3170, WM3270, WM3370, WM3500, WM3570, WM3600, WM3670, WM3700, WM3770, WM3900, WM4000, WM4270, WM4370 series and Kenmore 796-series front-load washers Often replaced together with the door lock switch (EBF61315802, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number MFG63099101 Part Type Washer Door Strike (Door Lock Hook / Latch Hook) Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore LG-built platform) Location Inside edge of washer door Material Metal Often Paired With Door Lock Switch (EBF61315802, sold separately) Error Codes Resolved DE1, DE2 (when caused by broken strike) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Don't Drop the Inner Glass Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a broken strike, use a putty knife to pry the white latch on the door lock through the bottom service opening to release the door. With the door open, locate the screws around the perimeter of the inner door panel. Remove the screws to release the inner door panel from the outer frame. Important: the inner glass insert is loose once the panel is unscrewed — support the glass with one hand as you pry the panel away to prevent it from falling out and breaking. Note the orientation of the old door strike (the direction it points and how it's seated). Use needle-nose pliers or tweezers to pull out the retaining pin holding the old strike in place, then remove the broken strike. Install the new MFG63099101 strike in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Reinsert the retaining pin to secure it. Carefully reposition the glass insert into the door, reinstall the inner door panel, and tighten the screws. Restore power and run a test cycle to confirm the door locks properly and there are no leaks. Tools needed: Phillips screwdriver, needle-nose pliers or tweezers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door strike and the door lock switch? These are two separate parts that work together to lock the washer door. The door strike (MFG63099101) is the metal hook attached to the inside edge of the washer door — when the door closes, the hook is what physically enters the lock assembly. The door lock switch (EBF61315802) is the assembly mounted on the front panel just inside the door opening — it contains the electromagnetic mechanism that grips and locks the strike, and the electrical sensor that tells the control board the door is closed. If the strike is broken, the lock has nothing to grip and the washer won't start. If the switch is broken, the strike can still enter the slot but the lock won't engage or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing strike has broken off inside the lock or the lock won't release, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the strike installation. Always disconnect power from the washer first. The number on my old strike doesn't match — is it still compatible? In many cases, yes. LG sometimes prints production batch codes on door strikes that look like part numbers but don't match the official OEM part number. As long as your washer's parts diagram lists MFG63099101 (or one of its cross-references: AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132), this strike is the correct fit. If you're unsure, contact our support team with your washer model number and we'll verify before you order. Should I replace the door lock switch (EBF61315802) at the same time? Not always, but often. The strike and the lock switch work together as a pair — if one is worn, the other has typically experienced the same load over thousands of cycles and is approaching the end of its service life. When a broken strike is the cause of the failure, examine the lock switch when the panel is open: if the lock mechanism shows visible wear, doesn't grip the new strike firmly, or has corroded contacts, replace it at the same time. Since the door is already partially disassembled and you have the washer apart, doing both at once saves a second repair session. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal to match the dimensions, mounting configuration, and lock-engagement function of the original MFG63099101 door strike used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X29528 Washer Door Lock The XPARTCO WH01X29528 is an aftermarket replacement door lock assembly compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Monogram front-load washing machines — as well as select GE UltraFast 2-in-1 combo washer/dryer units. The door lock is a safety mechanism mounted at the front of the washer where the door closes — it automatically engages when the door is shut, securing it closed for the entire wash and spin cycle so water and detergent can't spill out and cause injury. It also signals the control board that the door is safely locked, which is what allows the washer to start filling and running. When the door lock fails, the washer typically won't start, won't lock the door, stops mid-cycle, or throws a door-related error code. Rated 120 VAC, 60Hz, 16A. Failure usually comes from physical damage or normal wear over time. As a direct replacement for the GE WH01X29528, it also replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 (additional production markings: ITW 12070-71, V13305, 0024000128GE). Installation is straightforward with no wiring modifications — remove the old lock and install the new one, typically in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO WH01X29528 Washer Door Lock fixes GE, GE Profile, Café, and Haier front-load washers (and GE UltraFast 2-in-1 combo units) where the door won't lock or unlock, the washer won't start, the washer stops mid-cycle, the door feels loose or won't seal, or a door-latch error code appears. 120 VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, PS12749276, PD00060769, 4958749. Compatible with GE GFW510, GFW550, GFW650, GFW850, PFW870, PFW950, PFQ97 series front-load washers. No wiring modifications — installs in 10–15 minutes. Common Problems This Part Fixes Washer door won't lock at the start of the cycle Washer won't start — control board not detecting a locked door Washer door won't unlock at the end of the cycle Washer stops mid-cycle due to a door lock fault Door-latch related error code displayed on the control panel Door feels loose or doesn't seal properly Excessive noise and shaking while the washer is running (related to a door not securing properly) Intermittent locking — washer sometimes starts, sometimes doesn't Door lock assembly visibly broken, cracked, or with a failed latch Burning/electrical smell or humming from the door lock area (failed lock solenoid) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AGE26402, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, OEM20955948, V13305, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock assembly is compatible with select front-load washing machines and combo washer/dryer units from the following brands: GE front-load washers — GFW510 series (GFW510SCN0WW–SCN5WW, GFW510SCV0WW) GE front-load washers — GFW550 series (GFW550SPN0DG–SPN3DG, GFW550SPR0RS/SPR3RS/SPR4RS/SPR5RS, GFW550SSN0WW–SSN5WW) GE front-load washers — GFW650 series (GFW650SPN0SN–SPN4SN, GFW650SSN0WW–SSN4WW) GE front-load washers — GFW655 series (GFW655SPV0DS, GFW655SSV0WW) GE front-load washers — GFW850 series (GFW850SPN0DG–SPN5RS all DG/RS variants, GFW850SSN0WW–SSN5WW) GE Profile front-load washers — PFW870 series (PFW870SPV0RS, PFW870SSV0WW), PFW950 series (PFW950SPT0DS/SPT1DS/SPT2DS) GE Profile combo units — PFQ97HSPV0DS (UltraFast 2-in-1 combo washer/dryer) GE Café, Haier, Hotpoint, RCA, Monogram — select front-load models using the same door lock Sears Kenmore and Crosley — select GE-built front-load models Always verify your appliance model number before ordering. The WH01X29528 fits the specific models listed — please double-check your model number. Contact our support team if you're unsure. Key Features Door lock and switch assembly — locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Prevents the door from being opened mid-cycle, keeping water and detergent safely contained Resolves "won't lock," "won't unlock," "won't start," "stops mid-cycle," and door-latch error codes when caused by a failed lock Rated 120 VAC, 60Hz, 16A — correct electrical specifications for compatible GE front-load washers Integrates with the washer's main control board, door switch, and load detection system Durable, moisture-resistant materials resist deformation, wear, and short circuits for long service life No wiring modifications required — direct-fit replacement using the original connector Replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 Compatible with GE GFW510/GFW550/GFW650/GFW850, PFW870/PFW950, and PFQ97 series front-load washers and UltraFast combo units, plus select Café, Haier, Hotpoint, RCA, Monogram, Kenmore, and Crosley GE-built models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPWH01X29528 Part Type Washer Door Lock and Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers & Combo Washer/Dryer Units (GE platform) Voltage 120 VAC Frequency 60 Hz Amperage 16A Additional Production Markings ITW 12070-71, V13305, 0024000128GE Function Locks door during wash/spin; signals control board door is secure Location Front of washer at the door opening Compatible Brands GE, GE Profile, Café, Haier, Hotpoint, RCA, Monogram, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, you may need to access the manual release. Peel back the rubber door boot/gasket from the front panel edge near the lock to expose the door lock assembly — on some models this requires releasing the spring-loaded wire clamp that secures the boot with needle-nose pliers. Photograph the wire harness connection before disconnecting anything. Remove the mounting screws holding the door lock assembly to the front panel. Reach in and pull the assembly out through the door opening far enough to access the wire connector. Disconnect the wire harness plug from the old assembly (no wiring modifications are needed — it's a direct plug connection). Snap the new WH01X29528 assembly onto the wire harness plug until it clicks firmly, position it in the front panel opening, and secure it with the mounting screws. Press the rubber door boot back into its groove and reinstall the spring-loaded wire clamp if applicable. Restore power and test by closing the door and starting a cycle — confirm the door locks, the washer runs, and the door unlocks at the end. Tools needed: Phillips screwdriver, needle-nose pliers, work gloves. Frequently Asked Questions My GE washer won't start and shows a door error — is this the part? Very likely, yes. GE front-load washers won't start unless the control board receives confirmation from the door lock that the door is closed and locked — it's a safety interlock. When the door lock fails, the washer either won't lock the door, won't start, or displays a door-related message on the panel. If your door appears to close normally but the washer won't begin the cycle (or stops shortly after starting), the door lock is the most common cause. Replacing the WH01X29528 typically resolves it. If you've already replaced the door lock and the problem persists, the issue may be the main control board instead. I replaced the door lock and it worked briefly, then failed again — what's wrong? If a new door lock works for a short time (seconds to minutes) and then the washer goes back to showing a door error, the problem may not be the lock itself but the main control board that powers and monitors it. A control board with a failing door-lock circuit can damage or fail to properly drive the lock, causing repeated symptoms even after replacing the lock. Some customers report an electrical smell or humming from the lock in these cases. If you've replaced the door lock (especially more than once) and the door error returns, the main control board is the next component to investigate. Contact our support team with your model number for the correct control board part. Does this fit the GE UltraFast 2-in-1 combo washer/dryer? Yes — the WH01X29528 is used on select GE UltraFast 2-in-1 combo washer/dryer units (such as the PFQ97HSPV0DS) in addition to standalone GE front-load washers. The combo units use the same door lock design as the front-load washers in the GFW/PFW families. As always, confirm your specific model number against the compatibility list before ordering, since GE uses different door locks across different washer generations. How do I open the door if it's stuck locked and the washer won't run? If the door is stuck in the locked position because of a failed lock, first make sure there's no water in the drum (run or complete a drain cycle if possible). Then unplug the washer and wait a few minutes — some GE models release the lock after power is removed. If it's still stuck, most front-load washers have a manual release mechanism accessible from behind the lower kick panel at the front of the machine — a tab or cord you pull to manually disengage the lock. Consult your model's manual for the manual release location. Once the door is open, you can proceed with replacing the lock. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable, moisture-resistant materials to match the electrical specifications (120 VAC, 60Hz, 16A), connector configuration, mounting, and door-locking function of the original WH01X29528 door lock used in compatible GE, GE Profile, Café, Haier, and related front-load washers and combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 165256 Dishwasher Float Switch Replaces 00165256 Product Overview The XPARTCO 165256 Dishwasher Float Switch Replaces 00165256 is designed to monitor water levels inside the dishwasher and prevent overfilling. This float switch detects rising water levels and signals the control system to stop filling, protecting your appliance from leaks and water damage. Quick Answer If your dishwasher is overfilling, not filling correctly, or leaking due to excess water, the 165256 float switch may be faulty. Replacing it restores proper water level control and prevents overflow issues. Replaces Part Numbers Replaces OEM part number: 00165256, 165256, 935359, EAP8697040, ABS10088, PD00035415, AH3439096, EA3439096, PS3439096, AP2802373, PS8697040. Compatibility This dishwasher float switch is compatible with select Bosch, Thermador, and other compatible dishwashers. Bosch Dishwashers Thermador Dishwashers Compatible European-style Dishwashers Always verify your appliance model number before ordering. Common Problems This Part Fixes Dishwasher overfilling Water leaking due to excess fill Incorrect water level detection Dishwasher not filling properly Key Features Monitors dishwasher water level Prevents overfilling and leaks High-quality aftermarket replacement Reliable and durable construction Product Specifications Part Number: 165256 Part Type: Dishwasher Float Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dishwasher Water Level Control Troubleshooting Guide Dishwasher overfills → Faulty float switch Water keeps filling → Float switch stuck or failed Dishwasher won’t fill → Switch not detecting properly When Should You Replace This Float Switch? Replace this float switch if your dishwasher is overfilling, leaking, or not detecting correct water levels. Installation Notes ⚠️ Disconnect power and water supply before installation. Access the float switch inside the tub area and install securely according to your dishwasher model. Related Parts Water Inlet Valve Dishwasher Float Assembly Control Board Frequently Asked Questions Will this float switch fit my dishwasher?This part fits many Bosch and compatible dishwashers. Always verify your model number. What does a float switch do?It monitors water levels and prevents overfilling inside the dishwasher. What are signs of a bad float switch?Overfilling, leaking, or improper water level control. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO WH11X39237 Washer Drain Pump The XPARTCO WH11X39237 is an aftermarket replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH11X39237 Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Aftermarket replacement built to OEM-equivalent quality standards Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Aftermarket Replacement Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical specifications and physical dimensions of the original WH11X39237 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

ACP72929002CM Washer Shift Actuator Coupling Assembly Shift actuator. Fits specific LG top load washer models. Replaces Part Numbers: ACP72929002, 4323EA2001C, 1958330, 2653835, ACP73029001, AH3522903, EA3522903, 4323EA2001B, 1327673, AH3577589, EA3577589, AP5674447, AP5258825, PS7786658, PS3522903, AP5245586, PS3577589 Description: This Top Load Washer Coupling Assembly is a replacement component specifically designed for specific LG brand top-loading washing machine models. This assembly connects the agitator shaft to the transmission inside the washer, allowing oscillating motions to be transferred through the transmission from the motor.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO EBF49827801 Washer Door Lock 120V, 60Hz, lid lock and switch assembly. Fits select LG front load washers with front control panel. Replaces Part Numbers: EBF49827801, 6601ER1004C, 1268254, 1463541, 6601ER1004B, 6601ER1004E, 6601ER1004G, EBF49827802, AP4998848, PS3533609. Description: This Washer Door Lock Switch is a replacement part for select Kenmore, LG washing machine models. This critical safety feature locks the washer door during operation to prevent it from being opened, which ensures safety and proper functioning. The door lock switch also communicates with the washer's control system to indicate that the door is securely closed and the machine can begin its cycle. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WH23X28418 Washer Genuine GE OEM Drain Pump The WH23X28418 is a Genuine GE OEM replacement drain pump and motor assembly compatible with select GE, Hotpoint, Haier, RCA, and Kenmore top-load and front-load washers. The drain pump removes water from the washer drum during the drain and spin cycles — expelling water and detergent through the drain hose so that clothing comes out clean and free of excess water. When the pump fails, the washer will not drain, may leave standing water in the tub, or may produce loud noises during the drain cycle. This complete drain pump and motor assembly is rated at 120V, 60Hz, 1.25A with a duty cycle of 10 minutes on and 50 minutes off. It includes the pump and motor with harness — the harness and plug extend approximately 10 inches from the motor. The pump measures 5-1/4" L x 5-1/8" W x 5-1/2" H and includes a drain pump seal. It directly replaces WH23X24178 and WH23X27574, as well as several additional cross-reference numbers. Installs in 20–40 minutes with basic hand tools. Quick Answer The WH23X28418 Washer Genuine GE OEM Drain Pump fixes GE, Hotpoint, Haier, and RCA washers that won't drain, leave standing water in the tub, are noisy during draining, or leak around the pump area. Complete pump and motor with harness and drain pump seal. 120V/60Hz/1.25A. Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H; harness extends approx. 10". Replaces WH23X24178 and WH23X27574. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault or drain-related error code Loud humming, grinding, or buzzing noise during the drain cycle Washer pumps but will not spin — pump failure preventing cycle completion Water leaking from around the drain pump area Clothes not clean or coming out soaking wet due to incomplete drainage Pump impeller jammed by debris causing motor burnout Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH23X24178, WH23X28418, WH23X27574, 290D1201G001, 290D1201G002, 290D1201G003, AGE26155, B40-3A01, B30-3A02, PD00055680, EAP12723115, AP6889136, PS12723115. WH23X28418 is the current updated part number replacing the discontinued WH23X24178 and WH23X27574. If your washer documentation or old pump label shows either of those numbers, this is the correct replacement. Compatibility This drain pump is compatible with select washers from the following brands and series: GE top-load washers — GTW220, GTW330, GTW335, GTW460, GTW465, GTW485, GTW490, GTW500, GTW680, GTW720, GTW725, GTW750 series and others GE front-load washers — select GFW series models Hotpoint top-load washers — HTW200, HTW240 series and others Haier top-load washers — select models RCA top-load washers — select models Kenmore / Sears washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water and detergent from the washer drum during drain and spin cycles Complete assembly — includes pump motor, harness, and drain pump seal Rated 120V, 60Hz, 1.25A with a 10-minute on / 50-minute off duty cycle Dimensions: 5-1/4" L x 5-1/8" W x 5-1/2" H; harness and plug extend approximately 10" from motor Plastic and metal construction rated CL.A — durable and chemical resistant Includes drain pump seal to prevent leaks at the pump connection Current updated replacement for discontinued WH23X24178 and WH23X27574 — direct fit Note: The drain pump motor has been redesigned by the manufacturer — the replacement may look different from the original but fits and functions identically Genuine GE OEM part — factory-exact fit, materials, and specifications DIY-friendly repair — installs in 20–40 minutes with basic hand tools Product Specifications Part Number WH23X28418 Supersedes WH23X24178, WH23X27574 (both discontinued) Part Type Washer Drain Pump and Motor Assembly Condition Genuine OEM Application GE, Hotpoint, Haier, RCA Top-Load and Front-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.25A Rating CL.A Duty Cycle 10 minutes ON / 50 minutes OFF Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H Harness Length Approximately 10 inches from motor Color White / Black / Gray Material Plastic / Metal Includes Pump and motor with harness, drain pump seal Compatible Brands GE, Hotpoint, Haier, RCA, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Have towels and a shallow pan ready to catch residual water. For top-load GE washers, the drain pump is typically accessed from the bottom of the machine — carefully tilt the washer back onto a support or lay it on its side to reach the pump from underneath. Disconnect the outlet hose by loosening the hose clamp and pulling it free. Disconnect the electrical harness connector. Remove the mounting screws (typically three) securing the pump to the washer base. Twist and firmly pull the old pump out. Install the new WH23X28418 pump in reverse order — connect the hose, tighten the clamp, reconnect the harness, and secure the mounting screws. Restore power and water supply and run a test cycle to verify proper drainage and no leaks. Tools needed: Phillips screwdriver, flat-head screwdriver, slip-joint pliers, shallow pan. Frequently Asked Questions What is the relationship between WH23X28418, WH23X24178, and WH23X27574? All three are GE washer drain pumps — WH23X28418 is the current updated part number that replaced both the discontinued WH23X24178 and WH23X27574. GE redesigned the pump motor during its production cycle, so the replacement may look slightly different from the original, but it fits and functions identically. If your washer uses either of the older numbers, order WH23X28418. How do I know if my washer drain pump has failed? The most common signs are standing water in the tub after a cycle, the washer stopping mid-cycle with a drain error, or loud humming during the drain phase — which indicates the motor is running but the impeller is not moving. A grinding or rattling noise suggests debris in the pump or physical damage. If the pump is completely silent during what should be the drain cycle, the motor has likely burned out and the pump needs replacement. Does the WH23X28418 fit both top-load and front-load GE washers? The WH23X28418 is primarily used in GE and Hotpoint top-load washers — the GTW and HTW series make up the majority of compatible models. It also fits select GE front-load models. Always verify your specific model number before ordering to confirm compatibility for your washer type. What is the duty cycle rating and why does it matter? The duty cycle of 10 minutes on / 50 minutes off means the pump motor is rated for up to 10 consecutive minutes of operation before requiring a 50-minute rest period. In normal washer operation this is never an issue — drain cycles are brief. However, if a drain fault causes the pump to run continuously without successfully draining, the motor can overheat. If you replace the pump due to burnout and the new pump also fails quickly, check for a drain hose blockage or control board fault that may be causing the pump to run without limit. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications — the exact same drain pump and motor assembly installed in compatible models from the factory, with guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W11457841 Washer Lid Latch Strike The XPARTCO W11457841 is an aftermarket replacement washer lid latch strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid latch strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the latch strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid latch strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. This W11457841 aftermarket replacement is built to OEM-equivalent specifications and supersedes the earlier W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The XPARTCO W11457841 Washer Lid Latch Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic latch strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid latch strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid latch strike visibly broken, cracked, or missing on the underside of the lid Latch strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid latch strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid latch strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Aftermarket replacement built to OEM-equivalent quality standards — direct fit for compatible Whirlpool platform washers Plastic latch strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Latch Strike Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid latch strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old latch strike: rotate it counterclockwise until the retaining tab breaks free and pulls back, then pull the old latch strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the latch strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid latch strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid latch strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current part number that superseded it. Both are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this aftermarket part covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid latch strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the latch strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the latch strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid latch strike uses a twist-in design with no screws or hardware. To remove the old latch strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, twist-in mounting design, and lid switch activation function of the original W11457841 lid latch strike used in compatible Whirlpool, Maytag, and Kenmore HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH05X24185 Washer Clutch The XPARTCO WH05X24185 is an aftermarket replacement clutch for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This clutch engages and disengages the transmission during the wash and spin cycles, transferring the motor's power to spin the basket so your clothes finish damp rather than soaked. Made of white plastic with a glossy finish, measuring approximately 3"L x 3"W x 1"H. Sold individually and does not include any other parts, such as the shift actuator (our WH03X30517 listing) that works alongside it. Common causes of failure include wear and tear over time, excessive load, or mechanical obstruction. Symptoms of a worn or failing clutch include clothes coming out wet even after a completed spin cycle, a slight burning odor during operation, or issues with spinning or agitating. It directly replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473. Quick Answer The XPARTCO WH05X24185 Washer Clutch fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers where clothes come out wet after spinning, there's a slight burning odor during operation, or the washer has trouble spinning or agitating. White plastic, glossy finish, ~3"L x 3"W x 1"H. Sold individually. Replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473. If you also see grease pooling on the floor under the washer, that's more likely a transmission gearcase leak than this clutch — and if the agitator only slips in one direction, check the agitator bolt before assuming the clutch has failed. Common Problems This Part Fixes Clothes coming out wet even after a completed spin cycle Slight burning odor during operation Washer having trouble spinning or agitating Reduced washer performance from clutch wear Grinding or unusual noise tied to the transmission area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer clutch directly replaces the following OEM and cross-reference part numbers: WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This clutch is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform. Note: This clutch is commonly replaced alongside our WH03X30517 shift actuator, since the two work together in the same wash/spin transition system, but they are sold separately. If your washer also isn't switching between agitation and spin, check the actuator as well. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement clutch — engages and disengages the transmission during wash and spin Resolves "clothes still wet," "burning odor," and "trouble spinning or agitating" symptoms White plastic, glossy finish Approximately 3"L x 3"W x 1"H Direct drop-in replacement matching the original mounting Replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Aftermarket replacement built to OEM-equivalent quality standards Sold individually Product Specifications Part Number XPWH05X24185 OEM Part Number WH05X24185 Part Type Washer Clutch Condition Aftermarket Replacement Color White Material Plastic Finish Glossy Dimensions Approx. 3"L x 3"W x 1"H Related Part WH03X30517 shift actuator (sold separately) Repair Difficulty Moderate — some disassembly required Quantity 1 clutch (sold individually) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning to cut off electricity and prevent accidental shocks. Wear work gloves. Remove the two screws at the back of the washer with a Phillips head screwdriver, then pull off the main console and carefully set it aside. Locate the access plate on the transmission side and remove the screws securing it. Take the belt off the pulley and remove the belt guard. Remove the four screws that secure the clutch and take it off from the wet end of the transmission. Install the new WH05X24185 clutch and replace the four screws. Reattach the belt, pulley, and access plate, and replace their screws. Put the main console back onto the washer and secure it with the two screws. Restore power and run a test cycle to confirm clothes are coming out properly damp at the end of the spin cycle, with no burning odor or unusual noise. Tools needed: Phillips screwdriver, socket wrench, work gloves. Frequently Asked Questions My clothes come out wet after the spin cycle. Is this the clutch I need? Yes, this is one of the most common symptoms of a worn or failing clutch. Since this clutch is what engages the transmission to spin the basket at high speed, a worn clutch can slip rather than fully engaging, leaving clothes wetter than they should be at the end of the cycle. A slight burning odor during operation is another documented sign of the same wear. I noticed grease on the floor under my washer. Is that this clutch leaking? Not directly — grease pooling under the washer typically comes from the gearcase transmission itself rather than the clutch. If you're seeing this symptom, the transmission may need attention in addition to, or instead of, this clutch, depending on what else you're experiencing. My agitator slips going one direction but not the other. Is that the clutch? Not necessarily. This specific symptom — the agitator pulling fine in one direction but slipping in the other — is more often traced to a loose agitator bolt. It's worth checking and tightening that bolt first; if the problem persists, the agitator base hybrid assembly may need inspection before assuming this clutch is at fault. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the material, dimensions, and mounting configuration of the original WH05X24185 clutch used in compatible GE, Hotpoint, Haier, Monogram, and Café top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE4M137 Dryer High Limit Thermostat The XPARTCO WE4M137 is an aftermarket replacement high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip. This is a direct-fit aftermarket replacement built to the same temperature rating and mounting as the original thermostat. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause. Quick Answer The XPARTCO WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool. Common Problems This Part Fixes Dryer shuts off a few minutes into a heat-dry cycle Dryer stops early and won't restart until it cools down Intermittent shutdowns during the drying cycle Clothes coming out damp because the cycle keeps cutting short Dryer won't start at all if the thermostat has failed in an open position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M137, WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900 These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct replacement for this component regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including: Kenmore 2661532110, GE 2661532210 Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket high limit thermostat for GE-built dryers Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse Rated to open at approximately 315°F to prevent overheating damage Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number XPWE4M137 OEM Part Number WE4M137 Part Type Dryer High Limit Thermostat (Auto-Reset) Condition Aftermarket Replacement Temperature Rating L315-65F (Opens ~315°F, Auto-Resets on Cooling) Location Upper Right Side of Heater Housing Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure. Frequently Asked Questions My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need? Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause. Is this a one-time fuse like the thermal fuse, or does it reset itself? This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed. Why does my dryer keep tripping this thermostat? Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again. How do I test if this thermostat has failed? With the dryer unplugged, you can test the thermostat with a multimeter for continuity across its terminals at room temperature. No continuity when it should be closed (cool) is a sign it has failed and needs replacement. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

74009254 Range Fan Control Switch Replaces Part Numbers: WP74009254, 74009254, 04100131, 1035493, 12002045, 12002046, 12200015, 706171, 74007635, 7403P832-60, AP6011114, PS11744308. Genuine Whirlpool part

Read more less

EXPMS33 Microwave Door Switch Set – Universal Replacement for GE, Whirlpool, Samsung, LG & Kenmore Microwaves Product Description Restore safe and reliable microwave operation with the EXPMS33 Microwave Door Switch Set. This high-quality aftermarket kit includes the commonly used microwave interlock door switches, designed to ensure the unit operates only when the door is fully closed. Failed or worn door switches can cause the microwave not to start, stop mid-cycle, blow fuses, or run intermittently. Replacing the complete switch set helps restore proper door sensing and safe microwave performance. Note: All Switches are not the Same Replaces all Following Microwave Door Switch Parts number and more: Normally Closed Cross Reference Info: WB24X10075, WB24X800, WB24X830, WB24X0830, WB24X817, WB24X10112, FFSBA016 (No Fuse Included), 00606695, 5304408937 Normally open Cross Reference Info: 3B3362F, WB24X816, 6600W1K003C, QSWMA085WRE0, WB24X829, WB24X10180, 00606693, 00633795, WB23X10019, 241201600929, 5304408938. Compatibility This universal microwave door switch set fits many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, and Kenmore microwave ovens. Commonly used in countertop, over-the-range, and built-in microwave models that use standard NO (Normally Open) and NC (Normally Closed) interlock switches. Always confirm switch configuration and terminal layout before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Set – Designed to match OEM electrical performance 🚪 Complete Door Interlock Solution – Includes multiple switches for proper safety operation ⚡ Reliable Electrical Contacts – Ensures consistent microwave startup 💪 Durable Construction – Built for repeated door open/close cycles 🛡️ Fixes Common Issues – Solves microwave not starting, stopping mid-cycle, or blowing fuses 📐 Product Specification Part Number: EXPMS33 Component Type: Microwave Door Interlock Switch Set Include Switch Types: 2 X Normally Open (NO) and 1 X Normally Closed (NC) Voltage Rating: 125/250V AC | 16A, 1/2HP Terminal Type: Spade terminals Mounting: Snap-in brackets (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the microwave before servicing. Microwaves contain high-voltage components—always disconnect power before repair. Steps: Disconnect power from the microwave. Remove the outer cover or control panel as required. Locate the door switch housing near the latch assembly. Remove old switches one at a time, noting wire positions. Install the new EXPMS33 switches in the same locations. Reassemble panels and restore power. Test microwave operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore safe microwave operation — Add to Cart Now for a reliable, budget-friendly repair!

Read more less