Search results for "Furnace Safety"

XPARTCO EXP571 Dryer Door Catch The XPARTCO EXP571 is an aftermarket replacement door catch for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 1 door catch. Quick Answer The XPARTCO EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 1 catch per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 1 door catch per order Product Specifications Part Number EXP571 OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 1 Door Catch Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 1 door catch. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO S97018253 Range Vent Hood Light Fuse The replacement S97018253 Range Vent Hood Light Fuse is designed for select Broan range hood models. This replacement fuse protects the range hood’s light circuit from power surges or faults. Ideal for restoring functionality to select Broan range hoods experiencing light-related issues, such as non-functioning lights or intermittent power. Note: Disconnect power before installation. Handle glass fuse carefully. Replaces part numbers: S97018253, 1930589, 97018253, AP5616207, PS10280886. Compatibility (S97018253): Compatible with select Broan range hood models, including but not limited to: Broan: QP2, QP3, QP4 series (e.g., QP230BC, QP230BL, QP230SS, QP236BC, QP236BL, QP236SS, QP236WW, QP242BC, QP242BL, QP242SS, QP242WW, QP330BL, QP330SS, QP330WW, QP336BL, QP336SS, QP336WW, QP342BL, QP342SS, QP342WW, QP430SS, QP436SS, QP442SS) Verify your model number or contact our support team for assistance. Key Features (S97018253): ✅ Brand Compatibility: Fits select Broan range hood models. 🔥 Specifications: Replacement fuse, 8A, 120V, glass fuse (5x20mm), heat-resistant. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (e.g., screwdriver, pliers); typically installed in 10–15 minutes. 🛡️ Reliable Fixes: Addresses range hood light issues like non-functioning lights or intermittent power. Installation Notes (S97018253): Safety First: Disconnect the appliance from the power source before installation. Location: Typically found in the upper left corner of the range hood control board; remove filters and bottom pan to access. Tools: Use a screwdriver to access the control board and pliers to remove and install the fuse. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your microwave or range hood running today! Add to cart now for a budget-friendly fix!

Read more less

WPW10165425 Refrigerator Genuine Defrost Thermostat Replaces Part Numbers: WPW10165425, W10165425, 126393249SP, 12639324SP, 1455131, OEM24064262, AP6016065, PS11749348. Description: This Bimetal Defrost Thermostat is a Genuine OEM part for select Whirlpool refrigerator models. It plays a vital role in the defrost system, regulating the freezer temperature to prevent excessive frost buildup. The thermostat serves as a safety device by shutting off power to the defrost heater if the temperature gets too high, thereby protecting the appliance from overheating and potential damage.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

4TM-D14 Refrigerator / Freezer Compressor Overload Refrigerator / Freezer Thermal Overload Protector Replaces Part Numbers: WP4344040, 4344040, 10377011, 10377015, 14251316, 4343849, 4357157, 4434376, 61001898, 68001203, R0213308, AP6009230, PS11742383. Description: This Overload is a replacement for specific refrigerator models. It is an important component of the refrigerator's compressor system, providing protection against electrical overload. The overload helps safeguard the compressor from excessive electrical currents, preventing potential damage and ensuring the longevity of the refrigerator. It acts as a safety measure by interrupting the power supply to the compressor when necessary. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WB27X10542 Range Vent Hood Fuse – Compatible with GE and Hotpoint Range Hoods Product Description Protect your vent hood electronics from power surges and overheating with the XPARTCO WB27X10542 Range Vent Hood Fuse. This high-quality aftermarket replacement fuse interrupts electrical current when excessive heat or voltage occurs, safeguarding the control board and motor. A blown fuse can cause the vent hood lights or fan to stop working. Replacing it with this durable XPARTCO fuse restores safe, reliable operation at a fraction of the OEM cost. Replaces Part Numbers WB27X10542, 946789, AH239683, EA239683, PD00040792, AP3185501, PS239683. Compatibility This replacement line fuse fits select GE and Hotpoint range hoods. Example compatible models include (but are not limited to): GE JV347H1WW, GE JV348L1SS, and Hotpoint RVM1535DM1BB. Always verify your vent hood’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM performance for GE range hoods ⚡ Electrical Protection – Prevents control board and motor damage from power surges 💰 Budget-Friendly Fix – Reliable replacement at a lower cost than OEM 🛠️ Quick Installation – Direct-fit design requires only basic tools 🛡️ Fixes Common Issues – Solves power loss, fan not running, or lights not turning on 📐 Product Specification Part Number: WB27X10542 Component Type: Range Hood Line Fuse - FUSE 5 A 125V Material: Ceramic and metal fuse with insulated leads Mounting: Inline wiring harness or control board clip Operating Conditions: Rated for high-temperature kitchen environments Compliance: Built to OEM-equivalent safety standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the range hood or switch off the circuit breaker before performing repairs to prevent electrical shock. Steps: Disconnect power to the range hood. Remove the cover or control panel to access the fuse holder. Carefully disconnect the old fuse from its terminals. Install the new XPARTCO WB27X10542 fuse in the same orientation. Replace the cover, restore power, and test operation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore safe vent hood operation — Add to Cart Now for a reliable, cost-effective repair!

Read more less

XPARTCO 8577274 Dryer Thermistor - Compatible with Whirlpool, Kenmore, Maytag Product Description Ensure optimal drying performance with the XPARTCO 8577274 Dryer Thermistor. This replacement temperature-sensing resistor is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers, offering a cost-effective alternative to the original. It monitors air temperature changes during the drying cycle, providing feedback to the control board to regulate heat levels, preventing overheating and ensuring efficient drying. This part addresses issues like prolonged or shortened drying times, inaccurate temperature readings, or error codes, often caused by a faulty thermistor. Note: Includes (1) thermistor (mounting hardware not included). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP8577274, 8577274, 1181075, 3390292, 3406294, 3976615, 772546, ER8577274, WP8577274VP, PD00002401, EAP11746740, AP6013514, PS11746740. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: 3LCED9100WQ0, 7MGGW9200MW3, 7MWGD8300SW1, 7MWGD8500SR1, WED6200SW1, WED8000DW3, WED8300SW0, MEDB880BW0 Kenmore: 110.60884990, 110.6007299, 110.6093699, 110.7095299 Maytag: 7MMGDB850WL0, MVWC565FW0 KitchenAid, Amana, Inglis, Crosley: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, and Crosley dryers. Specifications: High-quality thermistor, approximately 11K Ohms at 70°F (21°C), located on blower housing. Reliable Performance: Monitors drum air temperature to prevent overheating and ensure efficient drying. Easy Installation: Requires 1/4-inch nut driver, small flathead screwdriver, and pliers; typically installed in 15–30 minutes. Effective Fixes: Resolves prolonged or shortened drying times, inaccurate temperature readings, or error codes. Product Specification Part Number: XPARTCO 8577274 Component Type: Dryer thermistor Material: Plastic and metal Electrical Specs: Approximately 11K Ohms at 70°F (21°C), varies with temperature Compliance: Prop 65 warning for California. Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO DC47-00016A Dryer Thermal Fuse The XPARTCO DC47-00016A is an aftermarket replacement thermal fuse for Samsung dryers. Mounted on the blower housing near the heat source, this fuse is a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb dangerously high — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to the dryer. That's why a blown thermal fuse produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. This fuse terminates in 1/4" male spade connectors for a direct plug-in fit. Unlike a thermostat, a thermal fuse cannot be reset once it blows — it must be replaced. Critically, a blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what the fuse is designed to react to. A failing thermistor can also cause repeated fuse blows, since the two work together to regulate temperature. It directly replaces 2068545, AP4201894, AP4201899, PS4205213, EAP4205213, PS2038378, PS2038533, and 35001087. Quick Answer The XPARTCO DC47-00016A Dryer Thermal Fuse fixes Samsung dryers that won't start at all — no lights, no tumble, no response to any button — after overheating from restricted airflow. 1/4" male spade terminals. Replaces 2068545, AP4201894, AP4201899, PS4205213, EAP4205213, PS2038378, PS2038533, 35001087. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after a load felt unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Dryer that recently smelled like burning or overheating before failing Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal fuse directly replaces the following OEM and cross-reference part numbers: DC47-00016A, L0016A, AP4201894, PS4205213, AP6008681, EAP4205213, OEM12605691, EAP11741821, ASM868996, PD00005341, PD00003747, PS11741821, 35001087, WP35001087. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Samsung dryers, and also fits select LG and Kenmore dryers built on a compatible platform, including model numbers such as: DV209AEW/XAA, DV210AEW, DV210AEW/XAA DV218AEB/XAA, DV218AEW/XAA, DV219AEW/XAA, DV220AEW, DV220AEW/XAA DV330AEW, DV350AEW/XAA, DV419AEW/XAA Note: This fuse is commonly paired with a matching thermistor (DC32-00007A) and thermostat (DC96-00887A / DC47-00018A), and manufacturer guidance recommends replacing the thermistor at the same time as the fuse, since the two work together and a failing thermistor is a common cause of repeated fuse blows. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement thermal fuse — one-time safety device that cuts power if the dryer overheats Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse 1/4" male spade terminal connectors for a direct plug-in electrical fit Mounts to the blower housing near the heat source Replaces 2068545, AP4201894, AP4201899, PS4205213, EAP4205213, PS2038378, PS2038533, and 35001087 Compatible with select Samsung, LG, and Kenmore dryers Aftermarket replacement built to OEM-equivalent quality standards Quick, simple repair — no special tools required beyond a basic screwdriver Product Specifications Part Number DC47-00016A OEM Part Number DC47-00016A Part Type Dryer Thermal Fuse (Thermal Cut-Off) Condition Aftermarket Replacement Location Blower housing, near the heat source Terminals 1/4" male spade connectors Resettable No — one-time use, must be replaced once blown Companion Parts Thermistor DC32-00007A, thermostat DC96-00887A / DC47-00018A Quantity 1 thermal fuse Compatible Brands Samsung, LG, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted, usually alongside the thermistor. Photograph the wiring before disconnecting the spade terminals from the old fuse. Remove the mounting screw holding the fuse in place and pull it free, disconnecting both spade terminal wires. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new DC47-00016A in the same mounting position, reconnect both spade terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the thermistor and thermostat checked as well, since a failing thermistor can also trigger repeated fuse blows. Can I just reset the thermal fuse instead of replacing it? No. Unlike a thermostat, a thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. Should I replace the thermistor at the same time as the fuse? It's worth strongly considering, and it's a common manufacturer recommendation. The thermistor and thermal fuse work together to manage temperature, and a failing thermistor can cause the dryer to run hotter than it should, leading directly to repeated fuse blows. Replacing both together, especially if your dryer has blown this fuse more than once, addresses the more likely root cause rather than just the symptom. My clothes came out extremely hot right before the dryer died. Is that related? Yes, this is a classic warning sign. Clothes coming out unusually hot indicates the dryer was already running hotter than normal, which is exactly the condition that leads to a blown thermal fuse. If you noticed this before the dryer stopped working, it strongly points to a ventilation or airflow problem that should be fully addressed before running the dryer again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications, spade terminal connections, and mounting configuration of the original DC47-00016A thermal fuse used in compatible Samsung, LG, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3977767 Dryer Hi Limit Thermostat 250 -80F Limit Thermostat. Fits specific Maytag, Kenmore, Whirlpool dryer models. Replaces Part Number: WP3977767, 3977767, 3399693, ER3977767, SET185, TJ90SET185, WP3977767VP, AP6009043, PS11742185. Description: This Hi-Limit Thermostat is a replacement part for specific Maytag, Kenmore, Whirlpool dryer models. It functions as a critical safety device that monitors and controls the temperature within the dryer, preventing it from overheating. When the dryer reaches a temperature that is too high, this thermostat will cut off the power to the heating element to mitigate the risk of fire.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 316489403 Gas Oven Igniter The XPARTCO 316489403 is an aftermarket replacement gas oven igniter compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges, ovens, and stoves. The oven igniter is the component that lights the gas burner — when you set the oven to bake or broil, electricity flows through the igniter, heating it until it glows bright orange. This heat both ignites the gas and draws enough current to open the gas safety valve, releasing gas to the burner. When the igniter weakens with age, it may still glow but no longer pull enough current to open the safety valve — so the oven fails to light, takes a long time to heat, or heats unevenly. This is a flat-style, open-cage igniter. Electrical rating: 3.2–3.6 amps, 120V AC. Made of silicon carbide and ceramic for high heat resistance and long service life. Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; the lead and plug measure approximately 16" long. Includes the flat-style igniter assembly with bracket and leads/plug. It directly replaces 316489403, 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063. Important: the igniter element is fragile — handle it only by the bracket, never by the element itself. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 316489403 Gas Oven Igniter fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ovens that won't light, take too long to heat, heat unevenly, or where you smell gas because the igniter is too weak to open the safety valve. Flat-style open-cage igniter. 3.2–3.6A, 120V AC. Silicon carbide/ceramic. Overall 3-1/2"L x 1-3/4"W x 13/16"H, 16" lead. Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, PS2364063. Handle by the bracket only — the element is fragile. Common Problems This Part Fixes Oven won't light or heat at all — igniter too weak to open the gas safety valve Oven takes a long time to reach temperature — igniter glowing but drawing insufficient current Oven heats unevenly or undercooks food — weak or slow ignition Igniter glows but the burner never ignites — classic sign of a degraded igniter Igniter doesn't glow at all — burned out or open circuit (no power reaching the burner) Gas smell when the safety valve opens but the burner doesn't light Oven runs erratically or won't maintain temperature Igniter visibly cracked, broken, or with a damaged element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas oven igniter directly replaces the following OEM and cross-reference part numbers: 316489403, 5304508786, 7316489403, Model 501RB, AH2364063, EA2364063, EAP2364063, AFR16172, AP4433236, PD00000756, PS2364063. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: on some models this is the broil (upper) igniter, and the bake (lower) igniter is a different part — see the FAQ below on bake vs broil igniters. Compatibility This gas oven igniter is compatible with select gas ranges, ovens, and stoves from the following brands: Frigidaire gas ranges and ovens — including many Frigidaire Gallery models (LGGF, FGGF, FFGF series and related) Electrolux gas ranges and ovens (select models) Crosley gas ranges and ovens (select models) Gibson gas ranges and ovens (select models) Kelvinator gas ranges and ovens (select models) Tappan gas ranges and ovens (select models) White-Westinghouse gas ranges and ovens (select models) Ikea gas ranges and ovens (select Frigidaire-built models) Kenmore / Sears gas ranges and ovens (select Frigidaire-built models, including 790-series) Note: This igniter fits specific models — always verify against your appliance's model number before ordering. On ranges with two igniters (a bake igniter and a broil igniter), confirm which one you need (see the bake-vs-broil FAQ below). Contact our support team with your model number if you're unsure. Key Features Gas oven igniter — heats up to ignite the burner and draws current to open the gas safety valve Flat-style, open-cage design Resolves "won't light," "slow to heat," "uneven heating," "glows but won't ignite," and "gas smell" symptoms caused by a weak or failed igniter Electrical rating: 3.2–3.6 amps, 120V AC Silicon carbide and ceramic construction — high heat resistance and long service life Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; lead and plug approximately 16" long Includes the flat-style igniter assembly with bracket and leads/plug (some kits include ceramic wire nuts) Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 316489403 Part Type Gas Oven Igniter (Flat Style, Open Cage) Condition Aftermarket Replacement Application Gas Ranges, Ovens, and Stoves (Frigidaire platform) Amperage 3.2–3.6 Amps Voltage 120V AC Igniter Style Flat, open cage Overall Dimensions 3-1/2"L x 1-3/4"W x 13/16"H Ceramic Block 1.5" L Lead Length Approximately 16" Material Silicon carbide / ceramic / metal Color Almond / White / Gray Includes Igniter assembly with bracket and leads/plug Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Shut off the gas supply to the range at the shutoff valve and disconnect electrical power at the breaker before beginning any repair. After installation, if you smell gas at any point, leave the area immediately and contact your gas utility provider. If you're not comfortable working around gas components, have this repair done by a qualified appliance technician. Improper gas appliance repairs can cause fire, explosion, or carbon monoxide hazards. ⚠️ Handle the Igniter by the Bracket Only — The Element Is Fragile Disconnect power at the breaker and shut off the gas supply before beginning. Wear work gloves and safety glasses. The silicon carbide igniter element is extremely fragile and cracks easily — handle the new igniter only by its metal bracket, never by touching the element itself. Skin oils and any impact can shorten its life or break it. Locate the igniter: the bake igniter is beneath the oven floor panel (remove the oven racks, then the floor panel, and on some models the bottom drawer for access), while the broil igniter is mounted near the top of the oven cavity. Photograph the wiring connection before disconnecting. Disconnect the old igniter's wire leads at the connector (they're often joined with ceramic wire nuts). Remove the screws securing the old igniter bracket and lift it out. Install the new 316489403 by securing its bracket in the same position and orientation, then connect the wire leads (use the included or existing ceramic wire nuts — regular wire nuts can't handle the heat). Route the leads away from the burner flame. Restore gas and power. Test by setting the oven to bake (or broil, if that's the igniter you replaced) — the igniter should glow bright orange within a minute or so, and the burner should light within about 60–90 seconds. Tools needed: Nut driver, Phillips screwdriver, work gloves, safety glasses. Frequently Asked Questions My igniter glows but the oven won't light — do I still need to replace it? Yes — this is actually the most common way an oven igniter fails, and it's counterintuitive. The igniter has two jobs: to get hot enough to ignite the gas, AND to draw enough electrical current to open the gas safety valve. As an igniter ages, it can still glow (so it looks like it's working) but weaken to the point where it no longer pulls enough current to open the safety valve — so no gas is released and the burner never lights. If your igniter glows orange but the burner doesn't light within about 90 seconds, the igniter is weak and needs replacement. A good rule of thumb: if it takes more than 90 seconds from glow to flame, the igniter is on its way out. Is the 316489403 the bake igniter or the broil igniter? This is an important distinction, and there's genuine confusion in the industry about it. On many Frigidaire gas ranges, the 316489403 is used as the broil (upper) igniter with an approximately 14–16" lead, while the bake (lower) igniter is a different part — 5304506545 (which superseded 316489404) — often with a shorter lead. However, some sources and parts diagrams list them differently or even reversed, and on some models the 316489403 serves the bake position. The safest approach: look up YOUR specific model number to confirm which igniter you need, and compare your old igniter's lead length to the replacement. If your old igniter's leads reach a connector far from the igniter (14–16"), the 316489403 with its 16" lead is likely correct. Contact our support team with your model number and we'll confirm. Why do I smell gas when I try to use the broiler? If you smell gas when the broiler's safety valve opens but the burner doesn't light, it usually means the igniter isn't getting hot enough (or drawing enough current) to ignite the gas that's being released — so raw gas escapes before shutting off. This points to a weak igniter. To confirm which part is at fault: with the gas off, do a voltage test at the oven safety valve on the broil side — you should read between 3.0 and 3.3 VAC. If the voltage is correct but the burner won't light, the igniter is the problem. If there's no proper voltage, or the burner tube has spider webs or debris blocking it, address those first. Also inspect the gas supply tube from the safety valve to the burner for damage or loose connections. Why do I need to handle the igniter so carefully? The igniter's heating element is made of silicon carbide, a material that's excellent at withstanding heat but is brittle and cracks easily from impact or flexing. Even touching the element with bare fingers can leave oils that create hot spots and shorten its life, and a small bump can crack it invisibly, causing premature failure. Always handle the new igniter by its metal bracket, never by the element or the ceramic block. When installing, be careful not to bump the element against the oven walls or burner. This care is the single biggest factor in whether your new igniter lasts years or fails early. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from silicon carbide and ceramic to match the electrical specifications (3.2–3.6A, 120V AC), flat open-cage style, dimensions (3-1/2"L x 1-3/4"W x 13/16"H, 16" lead), and ignition function of the original 316489403 gas oven igniter used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE04X29793 Dryer Genuine OEM High Limit Thermostat Fits Specific GE Dryer Models.  Replaces Part Numbers: WE04X29793, OEM20955920, AP6985305, PS12749247. Description: This High Limit Thermostat is a Genuine OEM replacement part for specific GE electric dryer models. Located internally near heating components .   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 35001087 Dryer Thermal Cut Off - Compatible with Samsung, Kenmore, Maytag Dryers Product Description Safeguard your dryer with the replacement XPARTCO 35001087 Dryer Thermal Cut Off. This thermal cut-off fuse is designed for select Samsung, Kenmore, and Maytag dryers, shutting off the heating element or burner when the dryer overheats to prevent fires or damage. It addresses issues like no heat, failure to start, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one thermal cut-off fuse with two 1/4" male spade terminals. Disconnect power before installation. Replaces part numbers: WP35001087, 35001087, 1122480, PD00003747, EAP11741821, AP6008681, PS11741821.  Compatibility: Compatible with models including but not limited to: Samsung: DV203AES, DV209AEW/XAA-0000, DV210AEW/XAA, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Maytag: MDE3000AYW, MEDB200VQ0, MEDB850WB0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, Maytag, Amana, and Inglis dryers. 🔥 Specifications: replacement thermal cut-off fuse, opens at 185°F (85°C), 25A at 125/250VAC. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, failure to start, or premature shutoff due to overheating. Product Specification Part Number: XPARTCO 35001087 Component Type: Thermal cut-off fuse Material: Plastic and metal Electrical Specs: 25A at 125/250VAC, opens at 185°F (85°C) Mounting: Two 1/4" male spade terminals, 1" between mounting holes (center to center) Operating Conditions: Suitable for high-temperature dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and operational today! Add to cart now for a budget-friendly fix!

Read more less

(5 Pack) EXP25A Ceramic Line Fuse, Fast Blow,  25A, 250V  It can be used in many applications.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less