WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit
The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet.
This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours.
Quick Answer
The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258.
Common Problems This Part Fixes
Dishes not getting clean — food soil, grit, or film left behind after a full cycle
Top rack not getting wet or not getting cleaned while the bottom rack washes normally
Spray arms turning slowly or not turning at all — insufficient water pressure
Loud humming, whining, or grinding noise during the wash portion of the cycle
Dishwasher runs a full cycle quietly with no audible water circulation
Water pooling in the base pan under the dishwasher from a leaking pump shaft seal
Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle
Cleaning performance that has gradually declined over months as bearings wear
Pump motor humming but the impeller not turning — seized shaft or jammed impeller
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers:
WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands:
GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series)
Café dishwashers (CDT865 and CDT866 series)
Monogram dishwashers (ZDT915 and ZDT975 series)
Hotpoint dishwashers (select GE-built models)
Haier dishwashers (select GE-platform models)
Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS.
Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile
Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed
Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump
Drives water through the lower spray arm, middle spray arm, and upper wash manifold
Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure
Sealed shaft design protects the motor from sump water intrusion
Direct drop-in replacement for the superseded WD26X22789 — no modifications required
Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms
Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WD26X25103
Part Type
Dishwasher Variable Wash Pump Kit (Circulation Pump)
Condition
Genuine OEM
Brand
GE Appliances
Motor Type
Variable speed
Voltage
120V / 60 Hz
Function
Circulates water under pressure to the spray arms and upper wash manifold
Kit Contents
Wash pump assembly + integrated wiring harness
Location
Underneath the tub, mounted to the sump housing
Connections
2 hose clamps + 2 electrical connections
Supersedes
WD26X22789
Repair Difficulty
Moderate — 1 to 2 hours
Quantity
1 pump kit
Compatible Brands
GE, GE Profile, Café, Monogram, Hotpoint, Haier
Installation Notes
⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves.
Frequently Asked Questions
My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump?
It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced.
What does "variable" mean on this pump, and does it matter?
It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly.
The dishwasher is making a loud grinding noise. Do I need the whole pump?
Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak.
I found water in the pan underneath the dishwasher. Could the pump cause that?
Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear.
Does this kit include everything, or do I need to reuse parts from the old pump?
The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks."
What's the difference between WD26X25103 and WD26X22789?
They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11665769 Dishwasher Sump Pump and Motor
Pump and Motor Assembly
Replaces Part Numbers: W11665769, W11085683, W10917110, W11164469, AP7212556, PS16875975.
Description: This dishwasher pump and motor assembly is compatible with specific Whirlpool, Maytag, Kenmore dishwasher models. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.
Genuine Whirlpool OEM
Whirlpool WP3946430 Washer Genuine OEM Timer Control
Factory-original quick-connect mechanical timer for select Whirlpool automatic washers.
Product Overview
WP3946430 is a Genuine Whirlpool OEM washer timer control. The timer controls the washer's electrical components and determines the duration and progression of the wash, rinse, drain, and spin portions of the selected cycle.
This is a quick-connect style timer designed for specific Whirlpool-built washer models. Match the complete washer model number and original timer part number before ordering.
Quick Answer
Yes — WP3946430 is a Genuine Whirlpool OEM washer timer. It replaces original timer numbers 3946430, 3351811, and 3347766.
Common Problems This Part May Fix
Washer will not advance through the cycle
Washer stops before completing a cycle
Selected cycle does not start or progresses incorrectly
Washer skips agitation, drain, rinse, or spin portions of a cycle
Timer contacts are worn, burned, or mechanically damaged
Timer failures can resemble lid-switch, motor, wiring, pump, or transmission problems. Diagnose the washer before replacing the timer.
Replaces and Cross-References
WP3946430, 3946430, 1126, 3347766, 3351811, J27-641, AP6008848, EAP11741989, PS11741989, AWP47890, PS11741989.
All cross-references are shown in one box for identification. Always verify by complete appliance model number.
Compatibility
Fits select Whirlpool automatic washers. Verified model examples include:
LA5500XSF1
LA5500XSG1
LA5500XSM1
LA5500XSN0
LA5500XSW0
LA5500XTG0
LA5580XTW0
LA6300XTM1
LA5668XTW0
LA8580XWG0
LA5580XSF2
LA5578XTN1
Important: This is a partial compatibility list. Whirlpool produced many similar washer timers with different internal contact sequences. Verify the complete washer model number and original timer number before purchase.
Key Features
Genuine Whirlpool OEM replacement part
Quick-connect washer timer
Controls cycle progression and timing
Controls electrical functions according to the selected cycle
Direct replacement for 3946430, 3351811, and 3347766
Product Specifications
Manufacturer Part Number
WP3946430
Manufacturer
Whirlpool
Part Type
Washer Timer / Timer Control
Connection Style
Quick Connect
Condition
New
Quality
Genuine OEM
Application
Select Whirlpool Automatic Washers
Installation Notes
Unplug the washer before service.
Remove the control-panel access hardware according to the washer service procedure.
Document the original timer wiring/connector positions before disconnecting the old timer.
Transfer the timer knob or dial components if required by the model.
Install the replacement timer and reconnect all plugs securely.
Reassemble the console and test the washer through a complete cycle.
Safety: Disconnect electrical power before installation. If you are not comfortable servicing line-voltage washer controls, use a qualified appliance technician.
FAQ
Is WP3946430 a Genuine Whirlpool part?
Yes. WP3946430 is a Genuine Whirlpool OEM washer timer.
What does this washer timer control?
It controls electrical components and the duration/progression of the washer's selected cycle.
Does WP3946430 replace 3946430?
Yes. It also replaces 3351811 and 3347766.
Can I choose a timer only by appearance?
No. Similar-looking timers can have different contact sequences. Always verify the complete washer model number and part number.
Shop With Confidence
Factory-original Whirlpool replacement part for supported washer models. Verify your complete appliance model number before ordering.
Genuine Whirlpool OEMQuick-Connect TimerModel Verification Recommended
DC97-14421A Genuine OEM Washer Tub Support
Description: The Spider Arm Assembly is an OEM component compatible with specific Samsung front-loading washing machines. It is the linkage mechanism connecting the transmission shaft and pulley system inside the drive motor. With integrated spring coils and joints, the multi-armed assembly facilitates smooth rotational movement of the wash basket essential for various cycles such as agitation, spinning, and drainage.
Replaces Part Numbers: DC97-14421A, 2076567, AP4452794, PS4220154.
W11281268 Genuine OEM Whirlpool Washer Drain Hose
The W11281268 is a genuine Whirlpool OEM external drain hose for Whirlpool, Maytag, and Amana washers. This hose carries wastewater from the washer to your house drain during the drain phase of every cycle, connecting to the washer's outlet spout on one end and to your standpipe or utility sink on the other.
This 6' black flexible hose features an elbow bracket and a grey 90-degree coupler end with a 1" inner diameter, and includes a metal clamp. The manufacturer has updated the design of the rubber fitting that attaches to the back of the washer since earlier versions of this hose were produced — the new fitting looks slightly different but fits and functions the same way as the original. Over time, drain hoses can crack, split, or become brittle with age, or may simply be missing if replaced or damaged during a move. A failing or missing hose typically shows up as water leaking or pooling near the back of the washer during the drain cycle, or no hose present at all on a newly acquired unit. It directly replaces WPW10267638, W10267638, W11250143, W11044871, W11198580, W11234073, and W11050506.
Quick Answer
The W11281268 Genuine OEM Whirlpool Washer Drain Hose fixes Whirlpool, Maytag, and Amana washers with a cracked, split, or missing drain hose, or water leaking near the back of the washer during the drain cycle. 6' black flexible hose, elbow bracket, 1" ID grey 90-degree coupler, metal clamp included. Replaces WPW10267638, W10267638, W11250143, W11044871, W11198580, W11234073, W11050506. You'll need to transfer your existing hose clamps onto the new hose during installation.
Common Problems This Part Fixes
Cracked, split, or leaking drain hose
Water pooling or leaking near the back of the washer during the drain cycle
Missing drain hose on a newly acquired or moved washer
Drain hose that's too short to reach the standpipe or utility sink
Brittle or deteriorated hose material from age
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drain hose directly replaces the following OEM and cross-reference part numbers:
W11281268, W11250143, W10267638, W11198580, WPW10267638, 4814006, W11044871, W11050506, W11234073, AP6784154, AWP44196, EAP12584563, FIX12584563, PD00044515, PS12584563.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain hose is compatible with select Whirlpool washers, and also fits select Maytag and Amana washers built on the Whirlpool platform.
Note: Whirlpool also sells a separate drain hose, W11244231, used on other Whirlpool and Maytag washer series (1CWTW4, 2DWTW, 3DWTW, 4GNTW4, 4KNTW, and related Kenmore 110.2 numbers) — this is a different part with its own cross-reference set. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hose your washer needs.
Key Features
Genuine Whirlpool OEM part — factory-specified length, coupler, and fitting design
Carries wastewater from the washer to your house drain during the drain cycle
Resolves "cracked or leaking hose," "missing drain hose," and "hose too short" symptoms
6' black flexible hose with elbow bracket
Grey 90-degree coupler end, 1" inner diameter
Includes metal clamp
Direct drop-in replacement — matches the original fitting and length
Replaces WPW10267638, W10267638, W11250143, W11044871, W11198580, W11234073, and W11050506
Compatible with Whirlpool, Maytag, and Amana washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W11281268
Part Type
Washer External Drain Hose
Condition
Genuine OEM
Brand
Whirlpool
Length
6'
Color
Black
Material
Rubber, flexible
Coupler End
Grey, 90-degree, 1" inner diameter
Includes
Elbow bracket, metal clamp
Repair Difficulty
Easy — basic hand tools, novice repair experience
Quantity
1 drain hose
Compatible Brands
Whirlpool, Maytag, Amana
Installation Notes
⚠️ Unplug Washer Before Starting — Transfer Your Old Clamps To The New Hose Unplug the washer, or shut off the house circuit breaker for the appliance, before beginning. Wear work gloves. Remove the back panel of the washer, then the lower front access panel to access the drain hose connection. Place a towel down before disconnecting any hoses to catch any remaining water. Squeeze the clamp ring with pliers and remove the old hose from the outlet spout on the back of the washer, and disconnect the other end from your standpipe or drain connection. You'll need to transfer your existing hose clamps onto the new W11281268, since a new one isn't included. Fit the new hose over the outlet spout and squeeze the clamp back into place with pliers, then reconnect the other end to your house drain. Reinstall the lower front access panel and back panel. Restore power and run a test cycle to confirm the hose is secure with no leaks. Tools needed: pliers, work gloves, towel.
Frequently Asked Questions
Is this repair difficult?
No, it's a very straightforward repair. Several customers describe it as simple as squeezing the clamp ring with pliers, fitting the new hose over the outlet spout, and moving the clamp back into place — no special tools or advanced skills required.
The rubber fitting looks different from my old hose. Did I get the wrong part?
No, this is expected. The manufacturer has updated the design of the rubber fitting that attaches to the back of the washer since earlier versions of this hose were made. The new fitting will fit and function exactly the same as the original, even though it may look slightly different.
Does this come with new hose clamps?
This hose includes its own metal clamp for the coupler end, but you'll still need to transfer your existing clamps from the old hose for the connections that don't come with a new one included. Keep your old clamps on hand during the swap rather than discarding them with the old hose.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length, coupler design, and fitting configuration of the drain hose originally installed on your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11612327 Dishwasher Genuine Circulation Pump
Circulation pump and motor assembly
Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935.
Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.
Genuine OEM 5220FR2075V Washer Water Valve
The Genuine OEM LG 5220FR2075V is the water inlet valve assembly for select LG and Kenmore front-load washers. The valve connects your home's water supply to the washer and opens and closes under control of the washer's control board, letting water into the tub and the detergent dispenser during each cycle. When it fails, the washer may fill slowly, fill with the wrong water, fill continuously, or not fill at all.
This is the original LG part. LG lists 5221ER1003M as an alternate number for this valve. Because LG makes several look-alike inlet valves that differ in coil count and connections, check your model number before ordering.
Quick Answer
The Genuine OEM 5220FR2075V Water Inlet Valve fixes an LG or Kenmore front-load washer that won't fill, fills slowly, fills with the wrong water temperature, or leaks or keeps filling at the valve. LG also lists it as 5221ER1003M. Classic symptom: the washer starts the cycle but stays empty or fills very slowly, and the water supply and hoses are fine.
Common Problems This Part Fixes
Washer won't fill with water
Slow filling, or a low water level
Detergent or bleach dispenser doesn't flush
Washer keeps filling or leaks at the valve
Water too hot or too cold because one inlet isn't opening
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This water inlet valve directly replaces the following part numbers:
5220FR2075V, ALG312873, AP7003066, PD00074485, 5221ER1003M, 4869495, ALG51888, AP6334246, EAP12579227, PD00050119, PS12579227
LG's Canadian parts catalog lists 5221ER1003M as an alternate to 5220FR2075V. This is a single-source cross-reference, so confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Similar-looking valves such as 5220FR2075L and 5221ER1003A are different parts and are not interchangeable with this one.
Compatibility
This valve is listed for LG and Kenmore front-load washers, including these examples:
LG WM3400CW, WM3500CW, WM3600HVA, WM3600HWA
LG WM3700HRA, WM3700HVA, WM3700HWA
LG F3L2CYV5T.ASSEVUS, F3P1CYV5T.ASSEVUS
Note: The models above are a sample from retailer listings, not an official full list. LG makes several inlet valves that look alike but differ in coil count and connections, so a wrong match is easy to make. Enter your model number at checkout or contact our support team to verify fit before ordering.
Key Features
Genuine OEM LG water inlet valve assembly
Controls water flow from the supply into the tub and dispenser
Also listed under LG alternate number 5221ER1003M
Resolves no-fill, slow-fill, and continuous-fill problems
Fits select LG and Kenmore front-load washers
Product Specifications
Part Number
5220FR2075V
OEM Part Number
5220FR2075V
Part Type
Washer Water Inlet Valve Assembly
Condition
Genuine OEM
Application
LG & Kenmore Front-Load Washers
Installation Notes
⚠️ Unplug Power and Shut Off the Water Unplug the washer and turn off both water supply valves before beginning. Wear work gloves, and have a towel and shallow pan ready for water left in the hoses. Pull the washer out and remove the rear or top panel as shown in your model's service guide. Disconnect the supply hoses, the wire connectors, and the dispenser hoses from the old valve, noting where each goes. Install the new valve in the same position, reconnect everything, and check for leaks with the water on before pushing the washer back.
Frequently Asked Questions
My washer won't fill. Is this the part I need?
A failed inlet valve is a common cause, but first check that both water supply valves are open and that the inlet screens at the hose connections aren't clogged. If those are fine and the washer still won't fill, the valve is a likely cause.
Is 5220FR2075V the same as 5221ER1003M?
LG's Canadian catalog lists 5221ER1003M as an alternate to 5220FR2075V. This is a single-source cross-reference, so check your model's parts diagram or ask our support team to confirm.
Can I use 5220FR2075L or 5221ER1003A instead?
No. They are different valves, and LG sells several that look alike. Use the number your model calls out, or contact our support team to confirm before ordering.
Will this fit my washer?
It is listed for select LG and Kenmore front-load washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
WPW10352973 Washer Genuine Dispenser Actuator
Dispenser Drawer Switch Actuator for Washer
Replaces Part Numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574.
✅ Product Description:
Restore proper detergent dispensing with this genuine OEM WPW10352973 washer dispenser actuator. Designed to control the flow of detergent and fabric softener into your wash cycle, this part is a direct replacement for worn or non-functioning actuators in many Whirlpool, Maytag, Amana, Kenmore, and Crosley top-load washing machines.
Part Features:
Genuine OEM quality – built to factory specs
Replaces part numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574.
Controls dispenser drawer movement for proper release timing
Easy to install with basic tools
Fixes the following symptoms:
Dispenser drawer not opening
Detergent or softener not dispensing
Error codes related to actuator failure
Inconsistent or incomplete wash cycles
Compatible with:Many models from Whirlpool, Maytag, Kenmore, Amana, and more.(Check model number before ordering or contact us for fitment help.)
✅ Why Buy from Parts-O-Matic?
Guaranteed OEM-quality parts
Always Fast and Free U.S. shipping
Competitive pricing
Expert support for part compatibility
🛒 Get your washer working like new – order the WPW10352973 Dispenser Actuator now at Parts-O-Matic.com, and enjoy fast, free shipping with no minimum.
XPARTCO W10721967 Washer Drive Clutch Kit
The XPARTCO W10721967 is an aftermarket replacement drive clutch kit — often called a "splutch" kit — for Whirlpool-built top-load washers. This assembly sits at the base of the transmission and works together with the mode shift actuator to control how power reaches the washer: during agitation, the clutch engages to drive the washplate back and forth, and during spin, it locks up to spin the inner wash basket at full speed. The name "splutch" comes from what it actually is — part spring, part clutch — and that spring-loaded design is what lets the same assembly smoothly transition between the gentle agitate motion and the much more forceful spin cycle.
This is a complete 6-piece kit: spring, clutch housing, cam ring, basket drive gear, drive pulley, and mounting nut, so you're replacing the entire wear-prone assembly at once rather than chasing individual worn components. Over time the clutch's friction surfaces glaze over and wear down, the cam ring's engagement points round off, and the spring loses tension — all of which produce the same telltale complaint: a loud grinding, clicking, or clunking noise during agitation or spin, sometimes alongside a washer that spins weakly, agitates but won't spin, or runs hot and starts to smell from the friction of a slipping clutch. It directly replaces AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10721967VP, W10818965, W11396423, 3319979, and PS10057144.
Quick Answer
The XPARTCO W10721967 Washer Drive Clutch Kit fixes Whirlpool-built top-load washers with loud grinding, clicking, or clunking noise during agitation or spin, a washer that agitates but won't spin, weak or no spin, an overheating smell, or a drum that doesn't spin the pump properly. Complete 6-piece "splutch" kit — spring, housing, cam ring, basket drive gear, pulley, and nut. Replaces AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10721967VP, W10818965, W11396423, 3319979, PS10057144. Often replaced together with the drive belt, since both wear on a similar schedule and share the same teardown.
Common Problems This Part Fixes
Loud grinding, clicking, or clunking noise during agitation or spin
Washer agitates normally but won't spin, or spins very weakly
Drive pump doesn't rotate properly, leading to slow or incomplete draining
Washer stops agitating partway through a cycle
Washer running unusually hot, sometimes with a burning or odd odor
Loud noise specifically when transitioning between agitate and spin
Clothes coming out excessively wet because the spin cycle isn't reaching full speed
Rattling or looseness felt at the drive pulley when the basket is turned by hand
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drive clutch kit directly replaces the following OEM and cross-reference part numbers:
W10721967, W10721967VP, AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10818965, W11396423, 3319979, PS10057144, EAP10057144, AWP40988, PD00005593.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drive clutch kit is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including:
Whirlpool top-load washers — WTW series
Maytag top-load washers — MVWC series (select Whirlpool-built models)
Kenmore top-load washers — KATW and NTW series (select Whirlpool-built models)
Amana top-load washers (select models)
Crosley top-load washers (select models)
Roper top-load washers (select models)
Inglis top-load washers (select models)
Verified model numbers include: 1CWTW4705GW0, 1CWTW4705GW1, 1CWTW4705GW2, 1CWTW4815EW0, 1CWTW4815EW1, 1CWTW4815EW2, 1CWTW4815EW3, 1CWTW4840YW2, 1CWTW4845EW0, 1CWTW4845EW1, 1CWTW4845EW2, 1CWTW4845EW3, 2DWTW4740YQ1, 4GWTW1805LW0, 4GWTW1805LW1, 4GWTW1955LW0, 4GWTW1955LW1, 4GWTW3000FW0, 4GWTW3000FW1, 4GWTW4740YQ3, 4GWTW4800YQ3, 4KATW5215FW0, 4KATW5415FW0, 4KMVWC215FW0, 4KMVWC315FW0, 4KMVWC410JW0, 4KMVWC415FW0, 4KMVWC420JW0, 4KMVWC425FW0, 4KMVWC430JW0, 4KMVWC440JW0, 4KNTW3100JW0, 4KNTW3200JW0, 4KNTW3300JW0, 7MWGT4027HW1, WTW5000DW1, and MVWX655DW1.
Note: This kit fits Whirlpool's belt-drive top-load washer platform specifically. It is not intended for direct-drive designs that don't use a separate clutch and belt system. Because this drive clutch kit fits an extremely broad range of model years and revisions, always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Complete 6-piece "splutch" kit — spring, clutch housing, cam ring, basket drive gear, drive pulley, and mounting nut
Works together with the mode shift actuator to engage agitation and lock up for full-speed spin
Resolves "grinding or clicking noise," "won't spin," "agitates but won't spin," and "overheating smell" symptoms caused by clutch wear
Replaces the entire wear-prone assembly at once rather than individual components
Direct drop-in replacement for the washer transmission's drive pulley and clutch assembly
Replaces AP5951296, W10006352, W10006353, W10006354, W10006356, W10006382, W10239973, W10315818, W10326374, W10536113, W10721967VP, W10818965, W11396423, 3319979, and PS10057144
Compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, Crosley, Roper, and Inglis top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
W10721967
OEM Part Number
W10721967 / AP5951296
Part Type
Washer Drive Clutch Kit ("Splutch")
Condition
Aftermarket Replacement
Application
Whirlpool-Built Belt-Drive Top-Load Washers
Kit Contents
Spring, clutch housing, cam ring, basket drive gear, drive pulley, mounting nut
Function
Engages agitation and locks up for full-speed spin
Repair Difficulty
Moderate — 30-45 minutes
Quantity
1 clutch kit (6 pieces)
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, Crosley, Roper, Inglis
Installation Notes
⚠️ Unplug Washer And Shut Off Water Before Starting — Tip Onto Its Back Or Front With Care Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Access is from underneath the washer: remove the inner wash basket first (this typically requires a large basket-hub or spanner tool and applying steady upward pressure to break the basket free from the drive hub), then carefully tip the washer onto its back or front, protecting the top and any control panel with a blanket or padding as you lay it down. Photograph the belt and pulley arrangement before disconnecting anything. Remove the drive belt from the motor pulley, then remove the mounting nut and pull the old clutch/pulley assembly off the transmission shaft — a puller tool can help if it's seized. Install the new W10721967 assembly onto the shaft in the same orientation, torque the mounting nut to the manufacturer's specification, and reinstall the drive belt, checking that it seats correctly in the pulley grooves. Carefully stand the washer back upright, reinstall the wash basket, and reconnect it to the drive hub. Restore water and power, then run a full test cycle through agitate and spin, listening for the grinding or clicking noise that prompted the repair. Tools needed: basket-hub removal tool or spanner wrench, socket set, 13mm socket, 5/16" nut driver, pliers, work gloves, and a helper to assist with tipping the washer.
Frequently Asked Questions
What does "splutch" mean, and why is it sold as one kit instead of individual parts?
"Splutch" is shorthand for spring-clutch — the assembly combines a spring-loaded clutch mechanism with the drive pulley and gear that together control agitation and spin. Whirlpool sells this as a single kit because the individual components wear together and interact closely; replacing just the pulley while leaving a worn cam ring or a fatigued spring in place often means the noise or slipping symptom returns quickly. Replacing the complete kit resolves the failure at its actual source.
My washer agitates fine but won't spin. Is this the clutch?
It's one of the most common causes of exactly that symptom. The clutch has to lock up firmly to transfer full power into spinning the basket; if its friction surfaces have worn down or glazed over, it can still engage well enough for the lighter agitation motion but slip under the higher torque demand of spin. If you hear grinding or clicking specifically as the washer transitions into spin, that reinforces the clutch as the likely cause.
Should I replace the drive belt at the same time?
It's worth strongly considering. The belt and clutch wear on a similar schedule and share the same teardown — you're already tipping the washer over and removing the belt to access the clutch, so replacing a belt that's showing wear at the same time saves you from repeating the whole disassembly again in the near future. Inspect the belt for glazing, cracking, or fraying while it's off and replace it if it shows any of those signs.
The washer smells hot or burnt. Is that dangerous, and does it point to this part?
A worn clutch that's slipping generates friction heat, which can produce a warm, slightly burnt smell — this is a real symptom of clutch wear and not something to ignore, since continued operation in that state accelerates wear on the clutch and can stress the drive motor. If you notice this smell along with weak or absent spin, stop using the washer and address the clutch before running further loads.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the spring tension, cam ring engagement geometry, pulley dimensions, and mounting configuration of the original W10721967 clutch kit used in compatible Whirlpool, Maytag, Kenmore, Amana, Crosley, Roper, and Inglis top-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly
The WPW10605057 is a genuine Whirlpool OEM circulation pump and diverter motor assembly for Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers. This assembly pumps water up through the spray arms throughout the wash cycle, and the integrated diverter motor controls which spray arm receives that water at any given moment. This assembly includes the circulation pump and diverter motor only — it does not include the drain pump, which is a separate component on this platform.
Over time, the pump motor's internal windings can wear out or fail electrically, or the diverter mechanism can stick or bind. A failing assembly typically shows up as a dishwasher that isn't washing dishes properly because water isn't circulating through the spray arms, or leaking from underneath the unit. Whirlpool's own guidance recommends checking the motor's resistance with a multimeter if water isn't circulating, to confirm the assembly before replacing it. It directly replaces AP6023350, WPW10482502, W10482502, W10605057, 3021439, 3023239, PS11756692, W10236194, W10534160N, W10300740, and W10500285.
Quick Answer
The WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly fixes Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers that aren't washing dishes properly because water isn't circulating, or that are leaking from underneath. Includes the circulation pump and diverter motor — not the drain pump. Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. Check the motor's resistance with a multimeter before replacing to confirm this assembly is actually the cause.
Common Problems This Part Fixes
Dishes not getting clean because water isn't circulating through the spray arms
Dishwasher leaking from underneath the unit
Weak or absent water spray during the wash cycle
Motor humming without spraying water normally
Inconsistent washing results from cycle to cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher pump and motor assembly directly replaces the following OEM and cross-reference part numbers:
WPW10605057, WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This pump and motor assembly is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers built on the Whirlpool platform, including model numbers such as KDTE104ESS, WDT710PAHZ, KDFE104DSS, WDT780SAEM, and WDT710PAHB.
Note — circulation pump only, not the drain pump: This assembly includes the circulation pump and diverter motor. The drain pump on this platform is a separate component and is not included with this assembly. If your dishwasher isn't draining rather than not washing properly, you likely need the drain pump instead. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dishwasher needs.
Key Features
Genuine Whirlpool OEM part — factory-specified pump and diverter motor design
Includes the circulation pump and diverter motor, which controls spray arm water flow
Resolves "not washing properly," "water not circulating," and "leaking underneath" symptoms
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692
Compatible with Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
DIY-friendly repair, typically about 30 minutes
Product Specifications
Part Number
WPW10605057
Part Type
Dishwasher Circulation Pump & Diverter Motor Assembly
Condition
Genuine OEM
Brand
Whirlpool
Function
Circulates water through the spray arms; diverter motor controls spray arm flow
Includes Drain Pump
No — sold separately
Repair Difficulty
Moderate — approx. 30 minutes
Quantity
1 pump and motor assembly
Compatible Brands
Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, Ikea
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the lower dish rack, the impeller/spray arm, and the drain filter to access the interior floor of the tub. Working from underneath the dishwasher, release the drain hose from the pump using pliers, then hand-unscrew the drain pump and temperature sensor about a quarter-turn each, being careful to release the small clip holding the drain pump in place — leave both of these components in place, since they're not part of this replacement. Release the three levers that clamp the pump and motor assembly to the bottom of the dishwasher, positioned roughly at 0, 120, and 240 degrees around the assembly. Photograph the electrical connections before disconnecting anything, since keeping track of exactly how everything was wired makes reassembly straightforward. Pop the old assembly up and out through the bottom of the dishwasher. If your old assembly used a separate counterweight, transfer it to the new assembly. Install the new WPW10605057 assembly through the same opening, reconnect all electrical connections exactly as photographed, and re-engage the three clamping levers. Reconnect the drain pump, temperature sensor, and drain hose you set aside earlier. Reinstall the drain filter, spray arm/impeller, and lower rack. Restore water and power, then run a test cycle to confirm normal water circulation with no leaks underneath. Tools needed: multi-screwdriver, pliers, work gloves.
Frequently Asked Questions
My dishwasher isn't cleaning dishes well. How do I know if this is the right part?
Whirlpool's own guidance recommends checking the pump motor's resistance with a multimeter first if water isn't circulating properly. If the motor tests outside its expected resistance range, or shows no continuity at all, that confirms this assembly has failed and needs replacing rather than a different component being at fault.
Should I replace the drain pump at the same time?
Not necessarily — this assembly doesn't include the drain pump, and if your dishwasher is washing normally but just not draining, the drain pump (a separate part) is the more likely cause rather than this circulation assembly. If both symptoms are present, it's worth checking both components, but they aren't sold together in this listing.
Do I need to replace the counterweight or reuse the old one?
If your dishwasher's original assembly used a separate counterweight component, transfer it from the old assembly to the new one during installation rather than assuming a new one is included. Check your specific model's parts diagram if you're not sure whether this applies to your dishwasher.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, diverter motor function, and mounting configuration of the circulation pump and motor assembly originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
