XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4)
The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine.
Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required.
Quick Answer
The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841.
Common Problems This Kit Fixes
Washer vibrating violently or shaking excessively during the spin cycle
Loud banging or thumping — tub striking the cabinet walls during spin
Washer "walking" or moving across the floor during high-speed spin
Error code dc displayed — Samsung out-of-balance error during spin
Error code UE displayed — unbalanced load error the washer cannot self-correct
Washer repeatedly stopping and rebalancing the load without completing the spin cycle
Visible broken, detached, or sagging suspension rod inside the washer cabinet
Rattling or clunking during agitation — tub no longer centered
Replaces Part Numbers
This suspension rod kit directly replaces the following OEM and cross-reference part numbers:
DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This suspension rod kit is compatible with select top-load washers from the following Samsung series:
Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models
Samsung WA41 series — WA41A3000AW and related models
Samsung WA42 series — WA422PRHDWR and related models
Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models
Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models
Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models
Kenmore / Sears top-load washers (select Samsung-built models)
Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet.
Key Features
Set of 4 suspension rods — complete replacement covering all four tub mounting points
Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact
Resolves Samsung error codes dc (out of balance) and UE (unbalanced load)
Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches
Spring steel construction with plastic end caps — durable and corrosion resistant
Rods are pre-coated with grease — wear work gloves during installation
Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support
No special tools required — installs in 20–30 minutes
Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
DC97-16350U
Part Type
Washer Suspension Rod and Spring Assembly
Condition
Aftermarket Replacement
Application
Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series
Quantity
Set of 4 (replace all four rods at the same time)
Rod Length
26.4–26.5 inches overall
Rod Diameter
1-1/4 inches
Material
Spring steel / Plastic end caps
Color
Brass / Black / White / Pink
Lubrication
Pre-coated with grease — wear gloves during installation
Error Codes Resolved
dc (out of balance), UE (unbalanced load)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves.
Frequently Asked Questions
What is the difference between DC97-16350U and DC97-16350V?
Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering.
Why must I replace all 4 rods instead of just the broken one?
All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair.
Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U?
Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U.
What do error codes dc and UE mean on Samsung washers?
Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases.
Is this an OEM or aftermarket part?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
DC64-01570A Washer Genuine Door Boot
Rubber boot assembly.
Fits select Samsung front-load washer models.
Replaces Part Numbers: DC64-01570A, DC97-14560A, DC97-14560K, DC97-14560L, AP4342244, PS4211426.
Description: This Washer Door Diaphragm is an essential component for maintaining your washer's functionality. This Genuine replacement part ensures a secure and effective seal, preventing leaks and enhancing the overall performance of your washing machine. Specifically designed for compatibility with a range of Samsung washer models, it guarantees a perfect fit and straightforward installation. Made from durable materials,
WPW10435242 Washer Genuine OEM Water Valve
Description: The Water inlet valve assembly is an OEM part for specific Whirlpool washing machine models. This valve assembly controls the flow of water entering the washing machine. It regulates water levels during different wash cycles like filling, rinsing, and draining.
Replaces Part Numbers: WPW10435242, W10435242, W10435236, AP6021375, PS11754698.
California Residents only
WARNING: California’s Proposition 65
XPARTCO 5221ER1003S Washer Water Valve
The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve.
Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number.
Quick Answer
The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order.
Common Problems This Part Fixes
Washer won't fill with cold water at the start of the cycle
Cold water fills much more slowly than it used to
Washer keeps filling continuously, even while water is simultaneously draining out
Water leaking steadily at the cold water connection point
Visible rust or mineral buildup around the valve body or connection
Cycle stalling at the fill step and never advancing to wash
Water pooling underneath or behind the washer near the cold supply line
Cold wash or cold rinse cycles specifically affected while other cycles run fine
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as:
LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW
LG W3600HVA
Kenmore WKE100HVA (select LG-built models)
Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers
Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure
Rated 12V with small male spade terminal connections for a secure electrical fit
Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L
Direct drop-in replacement — mounts underneath the top panel at the original connection point
Replaces 4869496, AP6798394, PS12587936, and EAP12587936
Compatible with LG and select Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair using basic hand tools
Product Specifications
Part Number
5221ER1003S
OEM Part Number
5221ER1003S (also 5221ER1003A)
Part Type
Washer Water Inlet Valve — Cold
Condition
Aftermarket Replacement
Brand
LG
Application
Front-Load Washers
Voltage
12V
Electrical Connection
Small male spade terminals
Color
Gray
Material
Plastic and metal
Height
4.75 in.
Width
3.25 in.
Length
2.25 in.
Location
Underneath the top panel, dispenser and control panel assembly
Quantity
1 valve
Compatible Brands
LG, select Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves.
Frequently Asked Questions
My washer keeps filling even while it's draining. Is that this valve?
Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis.
Cold water won't fill but hot water works fine. Is this the right part?
Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace.
I see rust on my old valve but it isn't leaking yet. Should I still replace it?
It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later.
What's the difference between 5221ER1003S and 5221ER1003A?
These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine Whirlpool 8212546RP Washer Fill Hoses 2-Pack 4 Feet - Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Kenmore
Product Description
Ensure reliable water supply for your washer with the Genuine Whirlpool 8212546RP Washer Fill Hoses 2-Pack. These OEM 4-foot black rubber hoses are designed for Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore washing machines, delivering hot and cold water with anti-corrosive brass couplings and pre-installed high-quality EPDM washers. With a 1050 PSI burst strength, they prevent leaks and ensure consistent water flow, addressing issues like leaking, low water flow, or hose failure.
Note: Includes two 4-foot hoses with built-in O-rings. Disconnect power and water supply before installation. Replace hoses every 5 years to reduce the risk of failure.
Replaces part numbers: 8212546RP, AP3885155, 1178876, 49535, 8212546IP, 8212546RW, PS1156134.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: WFW72HEDW0, WFW75HEFW0, WFW90HEFC0, WTW5000DW0
Maytag: MHW3500FW0, MHW5500FC0, MVWC565FW0, MVWB835DW0
KitchenAid: KSMW1030SS0
Jenn-Air, Amana, Kenmore: (select models, verify compatibility)
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore washing machines.
💧 Specifications: OEM 4-foot black rubber hoses with brass couplings, 1050 PSI burst strength, and EPDM washers.
💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability and leak-free operation.
🛠️ Easy Installation: Requires pliers and work gloves; typically installed in 10–15 minutes.
🛡️ Effective Fixes: Resolves leaking, low water flow, or hose failure issues.
Product Specification
Part Number: Genuine Whirlpool 8212546RP
Component Type: Washer fill hoses (2-pack)
Material: Black rubber with brass couplings, EPDM washers
Dimensions: 4 ft. length.
Mounting: 3/4" male and female connections with built-in O-rings
Operating Conditions: Suitable for hot and cold water in household washing machine environments
Compliance: Exceeds IAPMO, CSA, ANSI, IEC 61770, and RMA standards; Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the washer from the power source and turn off hot and cold water supplies before installation.
Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your washer running efficiently today!
Add to cart now for a reliable fix!
WPW10455261 Dishwasher Genuine OEM Pump and Motor Assembly
Fits specific Whirlpool, Maytag, Kenmore Dishwasher models
Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it.
Replaces Part Numbers: WPW10455261, W10455261, 2312159, W10500284, AP6021679, PS11755005.
California Residents only
WARNING: California’s Proposition 65
W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve
The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting.
Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP.
Quick Answer
The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first.
Common Problems This Part Fixes
Washer not filling with water
Washer filling very slowly
Water continuing to leak into the tub after the wash cycle has completed
No hot water reaching the tub, or no cold water reaching the tub
Cycle stalling at the fill step and never advancing to wash
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2.
Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate
Regulates hot and cold water flow into the washer tub
Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP
Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair
Product Specifications
Part Number
W11210459
Part Type
Washer Water Inlet Valve
Condition
Genuine OEM
Brand
Whirlpool
Application
Top-Load Washers
Function
Controls hot and cold water flow into the tub
Repair Difficulty
Moderate
Quantity
1 valve
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper
Installation Notes
⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves.
Frequently Asked Questions
My washer isn't filling with water. Is this the right part?
Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding.
What's the easiest way to access the control panel for this repair?
Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial.
Is this the same as W11210463?
No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH23X29553 Washer Water Valve
The XPARTCO WH23X29553 is an aftermarket replacement water inlet valve for GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. This valve controls the flow of water into the washer from the household supply line — when the control calls for a fill, the valve's solenoid opens to admit water, and closes again once the correct level is reached. Built with an ABS plastic body and stainless steel components for durability against corrosion.
Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve typically shows up as the washer not filling properly, filling too slowly, or leaking water. It directly replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA. As an aftermarket replacement, the WH23X29553 is built to OEM-equivalent quality standards.
Quick Answer
The XPARTCO WH23X29553 Washer Water Valve fixes GE front-load washers (and select Hotpoint, RCA, Haier, Monogram, and Café models) that aren't filling properly, are filling too slowly, or are leaking water near the valve connections. Replaces AP6983554, PS12743643, EAP12743643, 33090202, 0024000126GA. Not the same part as the similarly-numbered WH23X29538 valve — confirm you have the correct number before ordering.
Common Problems This Part Fixes
Washer not filling with water, or filling only partially
Washer fills much more slowly than it used to
Water leaking near the valve connections
Cycle stalling at the fill step and never advancing to wash
No hot water reaching the tub, or no cold water reaching the tub
Washer not washing properly due to insufficient or incorrect-temperature water
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water valve is compatible with select GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as:
GFW650SPN0SN, GFW650SPN1SN, GFW650SPN2SN, GFW650SPN3SN, GFW650SPN4SN
GFW650SSN0WW, GFW650SSN1WW, GFW650SSN2WW, GFW650SSN3WW, GFW650SSN4WW
GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS
GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW
GFW655SSV0WW
PFW870SPV0RS
PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS
Note — not the same as WH23X29538: A similarly-numbered valve, WH23X29538, is a separate part (replaces 4977241, AP6990115, PS16217225, EAP16217225, 33090201, 0024000126GB) used on related but distinct models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement built to match GE's factory-specified solenoid design and flow rate
ABS plastic body with stainless steel components for corrosion resistance
Resolves "won't fill," "fills slowly," and "leaking near the valve" symptoms caused by valve failure
Direct drop-in replacement — matches the original mounting and hose connections
Replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA
Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPWH23X29553
Part Type
Washer Water Inlet Valve
OEM Part Number
WH23X29553
Condition
Aftermarket Replacement
Brand
GE
Application
Front-Load Washers
Body Material
ABS plastic
Component Material
Stainless steel
Quantity
1 valve
Compatible Brands
GE, Hotpoint, RCA, Haier, Monogram, Café
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Release The Control Panel Carefully Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel on many models. When removing the front control panel, avoid pulling it straight out too far — slotted tabs on the right side of the panel can break if forced. Instead, pull the panel gently forward, then slide it to the right to release it cleanly. With the panel released, locate the valve and disconnect the hot and cold water supply hoses, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the outlet hoses from the old valve, remove its mounting screws, and pull it free. Install the new WH23X29553 in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the control panel and any surrounding trim, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly. Tools needed: Phillips screwdriver, pliers, towel, work gloves.
Frequently Asked Questions
How do I remove the front control panel without breaking it?
Avoid pulling the panel straight out with heavy force — the slotted tabs on the right side of the panel can snap if you pull too far. Instead, pull the panel gently forward first, then slide it to the right to release it from its mounting. This gentler approach avoids the most common way this panel gets damaged during a valve repair.
I've heard this valve sometimes needs replacing again after just a couple of years. Is that normal?
Some owners have reported needing to replace this valve again within a relatively short time, even after a successful repair. While most installations hold up well long-term, if you experience a repeat failure, it's worth double-checking your household water pressure and mineral content, since hard water and high pressure can accelerate wear on any water valve regardless of brand.
Is this the same as WH23X29538? The numbers look almost identical.
No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close match, since ordering the wrong one means it won't fit correctly.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, flow rate, and connection type of the original WH23X29553 valve used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11230103 Dishwasher Sump Pump and Motor
Replaces Part Numbers: W11230103, W10620220, 4591207, AP6329759, PS12349660.
Description: This Pump & Motor is an OEM part for Whirlpool dishwasher models. It serves as the heart of the wash system by providing water circulation and spray throughout all cycles. The pump circulates water mixed with detergent to clean dishes effectively.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WH22X37840 Genuine OEM GE Washer Main Control Board
The WH22X37840 is a genuine GE OEM main control board for GE and Profile UltraFresh front-load washers. This board is the washer's central processor — it reads every button press and cycle selection, drives the motor and inverter, opens and closes the water valves, runs the drain pump, and continuously monitors water level through an integrated water pressure switch built into the board itself. Because so many functions route through this single board, a failing control board can produce almost any symptom: a washer that won't power on, won't start a cycle, stalls partway through, fails to fill or drain, or runs a cycle that doesn't match what was selected on the display.
This board revises and supersedes WH22X36637, and also replaces WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517, WH22X36857, and WH22X37839. As a genuine OEM part, the WH22X37840 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Important: this board is not universal across GE's front-load lineup. It must be matched to your specific model and, after installation, programmed with the correct "personality" code for your washer before it will operate properly.
Quick Answer
The WH22X37840 Genuine OEM GE Washer Main Control Board fixes GE and Profile UltraFresh front-load washers that won't power on, won't start, stall mid-cycle, fail to fill or drain, run the wrong cycle, or have an unresponsive control panel. Genuine OEM, includes an integrated water pressure switch. Revises WH22X36637; also replaces WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517, WH22X36857, WH22X37839. Fits GFW650S, GFW850S, PFW870S, and PFW950S platforms. Requires programming a model-specific "personality" code after install, and the drain pump must be confirmed good before installing — a failed pump can damage a new board.
Common Problems This Part Fixes
Washer won't power on or the display stays completely dark
Washer won't start a cycle even though buttons respond and lights come on
Cycle stalls or stops partway through with no error explanation
Washer won't fill with water, or fills but never advances to wash
Washer won't drain or won't spin at the end of a cycle
Control panel unresponsive — button presses do nothing, or the wrong cycle runs
Display shows scrambled characters, flashing LEDs, or a persistent error code
Washer runs erratically — random starts, stops, or cycle changes on its own
Board that failed after repeated cycles where the drain pump was struggling
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer main control board directly replaces the following OEM and cross-reference part numbers:
WH22X37840, WH22X36637, WH22X35517, WH22X34659, WH22X30898, WH22X29532, WH22X32057, WH22X32457, WH22X36857, WH22X37839, AP7245609, AGE26864, PD00089582, PS17874601.
WH22X36637 was the immediately preceding number that GE revised to WH22X37840. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This main control board is compatible with select GE and Profile UltraFresh front-load washers, including:
GE front-load washers — GFW650S series
GE front-load washers — GFW850S series
GE Profile front-load washers — PFW870S series
GE Profile front-load washers — PFW950S series
Verified model numbers include: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN3SN, GFW650SPN4SN, GFW650SSN4WW, and PFW955SPW0DS.
Note: This board only works for the specific GE and Profile models listed above and must be programmed with the correct personality code for your washer after installation. It is NOT a universal front-load control board. If your model number is not listed above, ordering this board is likely to result in a board that installs but never runs correctly. Always verify your full model number before ordering, and contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified firmware, relay switching, and sensor interface
Functions as the washer's central processor, coordinating the motor, inverter, water valves, and drain pump
Includes an integrated water pressure switch — not available or serviceable as a separate part
Resolves "won't power on," "won't start," "stalls mid-cycle," "won't fill or drain," and "unresponsive control panel" symptoms caused by control board failure
Revises and directly replaces WH22X36637 and 7 additional legacy board numbers
Direct drop-in replacement for the original board mounting and harness connectors
Fits GFW650S, GFW850S, PFW870S, and PFW950S GE and Profile UltraFresh platforms
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WH22X37840
Part Type
Washer Main Control Board (Electronic Control Module)
Condition
Genuine OEM
Brand
GE / GE Profile
Application
GE and Profile UltraFresh Front-Load Washers
Integrated Components
Water pressure switch (built into board, not separately serviceable)
Programming Required
Yes — model-specific personality code must be set after installation
Supersedes
WH22X36637
Repair Difficulty
Medium — top panel removal and electrical connections required
Quantity
1 control board
Compatible Models
GFW650S, GFW850S, PFW870S, PFW950S series
Installation Notes
⚠️ 240V Circuit — Unplug Washer Before Starting. Verify Drain Pump First. Board Requires Programming. Disconnect power at the outlet or shut off the circuit breaker before beginning; front-load washers on this platform run on a 120V/240V circuit and internal components can retain a charge briefly after power is removed. Before replacing the board, confirm the drain pump is working correctly. A drain pump that has been struggling, clogged, or intermittently failing can send the control board erratic electrical feedback that damages a brand-new board the same way it damaged the old one — replacing the board alone, without checking the pump, is one of the most common reasons a "new" board fails again within days. Access is typically through the top panel: remove the rear top screws and slide the panel back, then locate the control board housing (commonly behind the top-front console or in a housing near the top of the cabinet, depending on model). Photograph all harness connections before disconnecting anything — this board has numerous connectors and getting even one out of place will cause a no-start or miswired symptom. Ground yourself before handling the board to avoid static damage to its electronics. Remove the mounting screws, disconnect each harness connector, and lift the old board free. Install the new WH22X37840 in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Before closing the washer back up, you must program the board with the personality code specific to your model. This is done through a button sequence on the control panel — press and release Start repeatedly until the display shows the personality ID number for your model, then confirm to save it; the control will return to an idle state once accepted. GE's official instructions (publication 99-3000289) detail the exact sequence and a Field Service Mode test if the LEDs don't flash correctly after programming — follow those instructions rather than guessing at the code, since an incorrect personality setting will cause the washer to behave unpredictably. Once programmed, reassemble the top panel, restore power, and run a full test cycle to confirm normal fill, wash, drain, and spin behavior. Tools needed: Phillips screwdriver, nut driver, anti-static wrist strap (recommended), and access to GE's personality programming instructions for your model.
Frequently Asked Questions
Do I really need to program the board after installing it?
Yes — this is not optional. The WH22X37840 is shared across several GE and Profile washer models, and it needs to be told which specific model it's installed in through a "personality" code before it will run correctly. Skipping this step, or entering the wrong code, will leave the washer behaving unpredictably even though the board itself is functioning normally. GE provides official programming instructions (publication 99-3000289) with the button sequence for your model — follow those closely rather than guessing.
Why does the listing say to check the drain pump before installing this board?
Because on this platform, a failing or clogged drain pump can feed electrical strain back into the control board that damages it over time — the same failure that likely killed your original board. If you install a new board without addressing a bad drain pump, there's a real risk of burning out the replacement as well. Before installing, run the pump through a diagnostic or physically inspect it for clogs, a seized impeller, or electrical failure, and address any issues found there first.
My washer won't power on at all. Is this the right part?
It's a strong candidate, but rule out the obvious first: confirm the outlet has power, check that the washer's power cord and connection are intact, and check the home's circuit breaker or a blown fuse. If those are all fine and the washer still shows zero signs of life — no lights, no display, no response to any button — the main control board has very likely failed and this board is the correct replacement.
What's the difference between WH22X37840 and WH22X36637?
They are the same board across production revisions. WH22X36637 was the prior GE part number and WH22X37840 is the current number that supersedes it. If your washer's parts diagram shows WH22X36637 or any of the older numbers (WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517), this listing is the correct replacement — it installs and programs the same way.
Does this board include the water pressure switch?
Yes. The water pressure switch that monitors fill level is integrated directly into this control board and is not available as a separate part per GE. If your washer's issue turns out to be water-level detection specifically — overfilling, underfilling, or an error related to water level — this board is the correct and only OEM fix, since the pressure switch cannot be replaced on its own.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It carries the same firmware, relay switching, integrated water pressure switch, and harness layout as the control board originally installed in your washer, and it is the officially supported replacement for your model once the correct personality code is programmed.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
285805 Genuine OEM Whirlpool Washer Water Inlet Valve
The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves.
This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517.
Quick Answer
The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly.
Common Problems This Part Fixes
Washer won't fill with water at the start of the cycle
Washer fills much more slowly than normal
Washer won't stop filling — overfilling past the normal level
Water leaking or dripping from the washer after the cycle has ended
No hot water reaching the tub, or no cold water reaching the tub
Washer not washing properly due to insufficient or incorrect-temperature water
Cycle stalling at the fill step and never advancing to wash
Hot water inlet blocked by calcium or mineral deposits after years of hard-water use
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including:
Whirlpool top-load washers and laundry centers
Maytag top-load washers (select Whirlpool-built models)
KitchenAid, Jenn-Air, and Amana top-load washers (select models)
Roper, Admiral, Hardwick, and Estate top-load washers (select models)
Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models)
Select Kenmore and Ikea top-load washers built on the Whirlpool platform
Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design
Complete kit — includes mounting bracket, screws, and installation instructions
Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections
Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure
One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform
Approximately 5.7" tall, metal and plastic construction
Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
285805
Part Type
Washer Water Inlet Valve Kit
Condition
Genuine OEM
Brand
Whirlpool
Application
Direct-Drive Top-Load Washers / Laundry Centers
Kit Contents
Water inlet valve, mounting bracket, screws, instructions
Ports
2 (hot and cold)
Hose Compatibility
1/2" ID
Thread Specification
Two 3/4"-11 x 1/2" NHT hose threads
Height
Approx. 5.7 in.
Material
Metal and plastic
Color
Blue or green (both correct — varies by production run)
Quantity
1 valve kit
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves.
Frequently Asked Questions
My valve is blue but the old one was green (or vice versa). Did I get the wrong part?
No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance.
The new valve's bracket doesn't match my old one. What do I do?
This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent.
Only hot water won't fill, but cold works fine. Is that this valve?
Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled.
My washer won't stop filling. Is that dangerous, and is it this valve?
It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W11688995 Washer Water Inlet Valve (Cold)
The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached.
When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools.
Quick Answer
The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately).
Common Problems This Part Fixes
Washer not filling with cold water — valve solenoid not opening when commanded
Washer filling slowly with cold water — valve partially clogged or weak solenoid
F8E1 error code displayed — cold water inlet valve fault
LO FL (low flow) error code — valve unable to deliver normal water flow
Fabric softener not being dispensed — cold water flush to dispenser failing
Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing
Water leaks at the valve body — internal seal failure
Wash cycles taking much longer than normal due to slow fill
Replaces Part Numbers
This cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select front-load washers from the following brands:
Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series
Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series
Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series
Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series
Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series
Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series
Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series
Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series
Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related
Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models
Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models
KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models
Kenmore / Sears front-load washers — select Whirlpool-built models
Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering.
Key Features
Aftermarket replacement built to OEM-equivalent quality standards
Controls the flow of cold water into the washer during fill cycles
Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped
Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve
1/2" NPT threaded inlet for standard washer supply hose connection
Dimensions: approximately 3" H x 4" W x 3" L
Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature
Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737
Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers
Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair
Quick DIY repair — installs in 10–15 minutes with basic hand tools
Product Specifications
Part Number
XPW11688995
Part Type
Washer Water Inlet Valve (Cold)
Condition
Aftermarket Replacement
Application
Front-Load Washers (Whirlpool platform)
Water Type
Cold (paired hot valve is W11688994)
Inlet Thread
1/2" NPT
Dimensions
Approximately 3" H x 4" W x 3" L
Color
Blue / White
Material
Plastic / Metal
Error Codes Resolved
F8E1, LO FL (when caused by cold valve fault)
Often Paired With
Hot Water Inlet Valve (W11688994, sold separately)
Compatible Brands
Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves.
Frequently Asked Questions
What do error codes F8E1 and LO FL mean on Whirlpool washers?
Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes.
My washer isn't dispensing fabric softener — could this be the cold valve?
Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue.
Should I replace the hot water valve at the same time?
Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit.
My washer is dripping water into the tub even when it's off — is this the valve?
Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
