Search results for "washer board"

W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) The W11688995 is a genuine Whirlpool OEM cold water inlet valve for Whirlpool-built front-load washers. Whirlpool's newer front-load platforms use two separate single-function valves instead of one combined hot/cold valve body — this cold-side valve handles only the cold water supply, while a matching hot-side valve (sold separately as W11688994) handles the hot side. When the control calls for a cold fill, it energizes this valve's solenoid coils to open the water path; when the correct level is reached, the valve closes again. If this valve fails to open, the washer won't take on cold water; if it fails to seal fully closed, water can trickle into the drum even when the washer isn't running. Because this is a dedicated single-function valve, a failure here shows up in a very specific way: cold-only fills stop working or slow down dramatically, while hot-only fills (governed by the separate W11688994 valve) continue working normally. Whirlpool's own service guidance links this valve to F8 E1 and LO FL fill-related error codes. Common failure modes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn internal diaphragm. It directly replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730. As a genuine OEM part, the W11688995 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) fixes Whirlpool-built front-load washers where cold water won't fill, fills slowly, overfills, leaks into the drum when off, or throws an F8 E1 or LO FL error code. 120V, 50/60Hz, two-coil cold-only valve, 1/2" NPT threaded connections. Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, EAP17216730. This is the cold-side valve only — the companion hot-side valve is sold separately as W11688994. Common Problems This Part Fixes Washer won't fill with cold water while hot water fills normally Cold water fills much more slowly than it used to Washer overfills or takes on more water than the cycle calls for Water trickling or leaking into the drum on the cold side when the washer is off F8 E1 or LO FL error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash Cold-wash or cold-rinse cycles specifically affected while warm/hot cycles run fine Water pooling underneath or behind the washer near the cold supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. W11486361 and W11316256 were earlier Whirlpool numbers for this same valve, with W11036930 preceding those. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including: Whirlpool front-load washers — WFW series Maytag front-load washers — MHW and MFW series (select Whirlpool-built models) Amana front-load washers (select models) Inglis front-load washers — IFW series (select models) Select Kenmore front-load washers built on the Whirlpool platform Verified model numbers include: 8TWFC6810LW0 (laundry center), IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4, MFW7020RF0, MFW7020RU0, MFW7020RW0, MHW5630HC0, MHW5630HC1, MHW5630HC2, MHW5630HC3, MHW5630HW0, MHW5630HW1, MHW5630HW2, MHW5630MBK0, MHW6630HC0 through MHW6630HC3, MHW6630HW0 through MHW6630HW3, MHW6630MBK0, MHW8630HC0 through MHW8630HC3, MHW8630HW0 through MHW8630HW3, WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW5620HW0 through WFW5620HW3, WFW6620HC0 through WFW6620HC2, WFW6620HW0, WFW6620HW1, WFW8620HC0 through WFW8620HC4, WFW8620HW0 through WFW8620HW4, WFW862CHC0, and WFW862CHC1. Note — cold side only: This is the cold water valve. The matching hot water valve for these same washers is sold separately under part number W11688994. The two are not interchangeable — each is a dedicated single-function valve, and installing this cold valve in place of the hot valve (or vice versa) will not correctly control water temperature. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Dedicated cold-only water inlet valve — two internal coils control flow to the cold supply Resolves "won't fill with cold water," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure Commonly resolves F8 E1 and LO FL error codes 1/2" NPT threaded connections for standard supply line hookups Direct drop-in replacement for W11036930, W11316256, and W11486361 Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730 Compatible with Whirlpool, Maytag, Amana, Inglis, and select Kenmore front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11688995 Part Type Washer Water Inlet Valve — Cold Condition Genuine OEM Brand Whirlpool Application Front-Load Washers (Whirlpool-Built) Voltage 120V Frequency 50/60 Hz Coils 2 (dedicated cold water function) Connection 1/2 in. NPT threaded Companion Part W11688994 (hot water valve, sold separately) Supersedes W11036930, W11316256, W11486361 Quantity 1 valve Compatible Brands Whirlpool, Maytag, Amana, Inglis, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply line from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit side by side and it's easy to cross a wire. Disconnect the electrical connector from the old cold valve, remove its mounting screw or bracket, and pull the valve free — leave the hot valve (W11688994) undisturbed if it isn't also being replaced. Install the new W11688995 in the same position, secure the mounting screw, and reconnect the electrical connector fully. Reattach the cold water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Reinstall the top panel, restore the water supply, and check the connection for leaks before restoring power. Run a short cycle set to a cold wash and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Cold water won't fill but hot water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Because your washer uses two separate single-function valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve (W11688994) keeps working independently. If cold-specific cycles are the ones failing, this cold valve is the correct part to replace. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11688995 valve alone is sufficient. If both hot and cold fills are having problems, or if the valves are original and quite old, some people choose to replace both at once since they're already accessing the same area — but it's not required. My washer shows an F8 E1 or LO FL error. Does that mean this valve is bad? It's a strong indicator, but check the basics first. These codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm the cold supply valve at the wall is fully open, check the inlet screen inside the valve port for sediment or debris, and make sure the cold fill hose isn't kinked. If those check out and cold water still won't fill properly, this valve is the likely cause. Can I use this valve on the hot water side instead? No. This is a dedicated cold-water valve, and the hot-water side uses a separate part number, W11688994. The two are built and calibrated for their specific supply line and are not interchangeable — installing the cold valve on the hot side (or vice versa) will not properly control water temperature during the cycle. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same two-coil solenoid design, seal, and flow-rate calibration as the cold water inlet valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH16X29509 Washer Damper Vent The XPARTCO WH16X29509 is an aftermarket replacement washer damper vent compatible with select GE, Hotpoint, RCA, and Kenmore front-load washers in the GFW510, GFW550, and GFW650 series. The damper vent is a one-way flap valve located on the drain system that automatically opens during draining to equalize pressure inside the drain pipe, allowing water to drain quickly and completely. When closed, it seals the drain path to prevent backflow of residual dirty water and lint from re-entering the drum and soiling clean laundry. Made from high-strength plastic with a reinforced hinge mechanism, this damper vent is designed to resist deformation under high-frequency operation and to prevent lint accumulation that can cause blockages. It directly replaces OEM part numbers WH16X29509, 4982970, AP6990392, and several additional cross-reference numbers. Snap-in installation requires no special tools and takes just minutes to complete. Quick Answer The XPARTCO WH16X29509 Washer Damper Vent fixes GE front-load washers displaying error codes 38, 39, 40, or 84, draining slowly, or returning dirty water or lint to clean clothes. The damper opens during draining and closes to block backflow. Compatible with GE GFW510, GFW550, and GFW650 series. Snap-in installation — no tools required. Common Problems This Part Fixes Slow or incomplete draining during the wash or spin cycle Dirty water or lint backflowing into the drum and soiling clean laundry Washer not draining fully, leaving standing water in the drum Drain hose blockages caused by a stuck or failed damper vent flap Moisture or odor buildup inside the washer due to poor drain ventilation Replaces Part Numbers This washer damper vent directly replaces the following OEM and cross-reference part numbers: WH16X29509, EAP16219913, FIX16219913, AGE26992, PD00079480, AP6990392, PS16219913. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This damper vent is compatible with select front-load washers from the following brands and series: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW850 series (select models) GE Profile front-load washers — PFW series (select models) Hotpoint front-load washers (select models) RCA front-load washers (select models) Kenmore / Sears front-load washers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-way flap valve — opens automatically during draining to equalize pipe pressure and ensure fast, complete drainage Seals shut when not draining — blocks residual dirty water and lint from backflowing into the drum and re-soiling clean laundry High-strength plastic construction with reinforced hinge — resists deformation under high-frequency operation Optimized airflow design minimizes lint accumulation for long-lasting, clog-free performance Heat-resistant materials — withstands high-temperature wash programs Direct replacement for WH16X29509 — snap-in installation, no special tools required Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WH16X29509 Part Type Washer Damper Vent (Drain Vent Flap Valve) Condition Aftermarket Replacement Application Front-Load Washers Function Equalizes drain pipe pressure during draining; blocks backflow when closed Material High-strength plastic Installation Snap-in — no special tools required Error Codes Resolved 38, 39, 40, 84 (on compatible GE models) Compatible Series GFW510, GFW550, GFW650, GFW850, PFW (select models) Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Unplug the washer from the power outlet before beginning any repair. The damper vent is located in the drain system — typically accessible from the front lower panel or by removing the washer's access panel. Locate the existing damper vent on the drain hose or drain port. Press the tabs or release clips to remove the old damper vent from its snap-in mounting position. Align the new WH16X29509 damper vent with the mounting port and press firmly until it snaps into place. Restore power and run a short drain or rinse cycle to verify the washer drains correctly and no error codes are displayed. Tools needed: None for the damper vent itself; a screwdriver may be needed to remove the access panel on some models. Frequently Asked Questions What does the washer damper vent do? The damper vent is a one-way valve on the washer's drain system. During the drain cycle, it opens automatically to equalize the air pressure inside the drain hose, which allows water to drain quickly and completely. When draining stops, the flap closes to create a seal that prevents residual wastewater and lint from flowing back up the drain hose and into the drum — which would re-soil clothes that have already been washed. What error codes does a failed damper vent cause on GE washers? A blocked, stuck, or failed WH16X29509 damper vent is a known cause of error codes 38, 39, 40, and 84 on compatible GE GFW510, GFW550, and GFW650 series front-load washers. These codes are typically triggered when the control board detects a drain pressure or flow issue. Replacing the damper vent resolves the issue in many cases when the drain pump and hose are otherwise clear. How do I know if my damper vent has failed? Common signs of a failed damper vent include slow or incomplete draining, one of the error codes listed above, dirty water or lint reappearing on clothes after a wash cycle, or a stuck flap that is visibly open or closed when it should not be. You can inspect the damper vent by removing the access panel and checking whether the flap moves freely — it should open easily when you apply gentle pressure and spring closed when released. Is the WH16X29509 compatible with GE Profile and GE Café washers? The WH16X29509 is confirmed compatible with select GFW and PFW series models from GE and GE Profile. GE Café washers use different model series — verify your specific model number before ordering. Contact our support team if you need help confirming compatibility for your Café or Profile model. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from high-strength plastic to match the dimensions and performance of the original WH16X29509 damper vent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WP21352320 Genuine OEM Whirlpool Washer Drive Belt The WP21352320 is a genuine Whirlpool OEM drive belt for Whirlpool top-load washers. This belt connects the drive motor to the transmission at the bottom of the washer, and it's what actually spins the basket during the wash and spin cycles. Unlike a dryer's drum belt, which simply tumbles a drum, this washer drive belt has to transfer real torque to spin a heavy, water-filled basket, which puts it under considerably more mechanical stress. Measuring approximately 51" long and 3/8" wide. A worn or broken belt produces a distinctive set of symptoms: the washer may not spin at all, spin only slowly, agitate poorly or not at all, fail to drain properly since the pump relies on the same drive system, or produce a burning smell or loud grinding noise as a worn belt slips against the pulley. One useful diagnostic tip worth knowing: a belt can look intact at a glance but still be worn out — if the sides of the belt appear shiny or glazed rather than matte, that's a sign of slippage-related wear even without a visible crack. It directly replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882. Quick Answer The WP21352320 Genuine OEM Whirlpool Washer Drive Belt fixes Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers with a drum that won't spin, spins slowly, won't agitate, won't drain, or produces a burning smell or loud grinding noise. Approximately 51" long, 3/8" wide. Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, PS11738882. A belt can look intact but still be worn out — check the sides for a shiny, glazed appearance, which indicates slippage wear even without a visible crack. Common Problems This Part Fixes Washer drum won't spin, or spins only slowly Washer won't agitate during the wash cycle Washer won't drain properly Burning smell coming from the washer during operation Loud grinding noise from underneath the washer Washer that shakes or moves excessively during spin Washer that won't start or stalls partway through a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP21352320, 21352320, 21001478, 35-2073, 35-2320, 35-3662, PD00002418, EAP11738882, AP6005822, AWP46532, PS11738882, WP21352320VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Whirlpool top-load washers, and also fits select Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, and Ikea washers built on the Whirlpool platform, including model numbers such as HAV3460AWW. Note: Always verify your full model number before ordering, since Whirlpool uses several different drive belts across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, width, and material Connects the drive motor to the transmission to spin the basket Resolves "won't spin," "won't agitate," "won't drain," "burning smell," and "grinding noise" symptoms caused by belt failure Approximately 51" long, 3/8" wide Direct drop-in replacement matching the original belt routing Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882 Compatible with Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP21352320 Part Type Washer Drive Belt Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Length Approx. 51 in. Width 3/8 in. Attaches To Motor pulley and transmission Repair Difficulty Medium — basic hand tools required Quantity 1 drive belt Compatible Brands Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, Ikea Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Consider The Motor Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker, and shut off both the hot and cold water supply valves before beginning. Pull the washer out from the wall for full access. Wear work gloves. Locate the drive belt around the motor at the bottom of the washer. Use a flathead screwdriver or hex wrench to remove the screws holding the motor bracket in place, which releases tension on the belt. Carefully slide the motor bracket off the motor, and use pliers if needed to work the old belt off the pulley. While the bottom of the washer is accessible, this is a good time to inspect the motor pulley for wear as well, since it's a related component you'll already have exposed. Install the new WP21352320 belt around the pulley and transmission, following the same routing as the old belt, and make sure it's seated securely and tightened properly — a loose or improperly seated belt will slip and wear out quickly. Reattach the motor bracket with its screws. Restore the water supply and power, then run a test cycle to confirm the washer spins, agitates, and drains normally with no unusual noise. Tools needed: multi-bit screwdriver, hex wrench, standard pliers, work gloves. Frequently Asked Questions My belt looks fine — no cracks or visible damage. Could it still need replacing? Yes, and this is a common source of confusion. A belt can appear intact with no cracks and still be worn out. Check the sides of the belt closely: if they look shiny or glazed rather than having a matte, textured surface, that glazing indicates the belt has been slipping against the pulley, which is a clear sign of wear even without visible cracking. My washer pumps and drains but the drum spins slowly or not at all. Is this the belt? Yes, this is one of the most direct symptoms of a worn or slipping drive belt. Since this belt is what actually transfers the motor's power to spin the basket, a worn belt can slip under load, causing slow or absent spinning even though the motor itself and the drain pump are both working normally. Should I replace the motor pulley at the same time? It's worth inspecting while you have the bottom of the washer accessible, even if you don't end up replacing it. A worn pulley can accelerate wear on a brand-new belt, so checking its condition during this repair is a reasonable precaution, especially if your old belt showed the glazed, slipping-related wear pattern. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and routing configuration of the drive belt originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10226427 Refrigerator Genuine OEM Power Supply Board Replaces Part Numbers:  WPW10226427, W10226427, 1551792, OEM18052172, AP6017389, PS11750687. Description: This is a Genuine OEM refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with specific refrigerator models made by Kenmore, Whirlpool, Maytag, and KitchenAid.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W11130362 Washer Suspension Rod Kit The XPARTCO W11130362 is an aftermarket replacement suspension rod kit for Whirlpool top-load washers. The wash tub inside a top-load washer hangs suspended inside the cabinet, and this set of rods is what supports that tub and absorbs the vibration and movement it generates during unbalanced loads and high-speed spin. Without healthy suspension rods, the tub can bang against the cabinet, shake the whole machine, and produce loud, rhythmic noise that gets worse the more unbalanced a load is. This kit includes 4 suspension rods, 4 bushings, and 4 suspension balls, plus installation instructions — everything needed to replace the full suspension system in one job. Each steel rod measures approximately 23.3" long, with plastic components at the connection points. Over time, the bushings and balls wear down, and the rods themselves can lose their damping effectiveness, producing a loud banging or rattling noise often described as a "death rattle" during spin. It directly replaces W10594080, W10735786, W10748956, W10780040, W10821710, W10901056, W11027174, W11033491, W11228718, and W11035751. Quick Answer The XPARTCO W11130362 Washer Suspension Rod Kit fixes Whirlpool, Maytag, Kenmore, and Crosley top-load washers with loud banging, rattling, or a "death rattle" noise during spin, excessive tub movement, or a washer that feels unbalanced even after leveling. Complete kit: 4 rods, 4 bushings, 4 suspension balls. Each rod approx. 23" long. Replaces W10594080, W10735786, W10748956, W10780040, W10821710, W10901056, W11027174, W11033491, W11228718, W11035751. Replace all four rods together, even if only one has failed — uneven wear across the set reduces the effectiveness of the whole suspension system. Common Problems This Part Fixes Loud banging, knocking, or rattling noise during the spin cycle Washer tub that moves excessively or bounces during unbalanced loads Washer that shakes or "walks" even after the unit has been leveled Persistent rattling noise sometimes described as a "death rattle" Tub that wobbles noticeably when pushed by hand Noise that has gradually gotten worse over the years Washer that seems off-balance even with a properly distributed load Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer suspension rod kit directly replaces the following OEM and cross-reference part numbers: W11130362, W11027174, W10780040, W10594080, W10735786, W10748956, W10821710, W10901056, W11033491, W11228718, AP6262443, AWP43166, EAP12347546, PD00038547, PS12347546 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select Whirlpool top-load washers, and also fits select Maytag, Kenmore, and Crosley top-load washers built on the same platform, including model numbers such as: WTW5000DW, WTW5000DW1, WTW5000DW2, WTW5000DW3 WTW5005KW MVWC565FW, MVWC565FW0, MVWC565FW1, MVWC565FW2 MVWX655DW, MVWX655DW1 MVWC555DW Note: Always verify your full model number before ordering, since Whirlpool uses different suspension systems across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement suspension rod kit — supports and dampens tub movement during spin Complete kit includes 4 suspension rods, 4 bushings, and 4 suspension balls Resolves "banging or rattling noise," "excessive tub movement," and "washer that feels unbalanced" symptoms caused by worn suspension Durable steel rods with plastic components at the connection points Each rod approximately 23.3" long Direct drop-in replacement — no modification required Replaces W10594080, W10735786, W10748956, W10780040, W10821710, W10901056, W11027174, W11033491, W11228718, and W11035751 Compatible with Whirlpool, Maytag, Kenmore, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W11130362 OEM Part Number W11130362 Part Type Washer Suspension Rod Kit Condition Aftermarket Replacement Application Whirlpool-Platform Top-Load Washers Kit Contents 4 suspension rods, 4 bushings, 4 suspension balls, installation instructions Rod Length Approx. 23.3 in. each Material Steel rods with plastic components Function Supports the tub and dampens vibration during spin Repair Difficulty Medium — basic hand tools and some disassembly required Quantity 1 kit (4 rods, 4 bushings, 4 balls) Compatible Brands Whirlpool, Maytag, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Replace All Four Rods Together Disconnect power at the outlet and shut off the water supply before beginning. Place a towel underneath the washer to protect the floor from any residual water. Wear work gloves. Open the lid and locate the suspension rod kit connecting the tub to the cabinet. Photograph how each old rod, bushing, and ball connects at both ends before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Use a flathead screwdriver to loosen the screws securing each rod assembly, then carefully pull each one free. Replace all four rods, bushings, and balls together, even if only one position shows obvious wear — the manufacturer specifically advises replacing the full set at once, since uneven wear across the suspension system reduces its overall effectiveness. Install each new rod assembly in the same position, making sure it fits snugly, and tighten the screws securely. Once all four are installed, gently rock the tub by hand to confirm even resistance at each corner before closing the lid. Restore water and power, then run a full spin cycle to confirm the noise and excess movement have resolved. Tools needed: flathead screwdriver, pliers, adjustable wrench, work gloves. Frequently Asked Questions My washer has a loud "death rattle" during spin. Will this kit fix it? Yes, this is one of the most common symptoms this kit resolves. Worn suspension rods, bushings, and balls lose their ability to dampen the tub's movement, and the result is often described as exactly this kind of loud, persistent rattling or banging during spin. Replacing the full suspension system typically restores quiet, stable operation. Do I really need to replace all four rods, or just the one that's broken? It's strongly recommended to replace all four together, and it's the manufacturer's own installation guidance for this kit. All four rods are typically the same age and under the same stress, so if one has worn out or broken, the others are likely not far behind. Replacing only one risks leaving the tub unevenly supported and having to repeat this repair again soon. My washer is off-balance even though it's level and the load looks even. Could this be the cause? Yes, this is a good sign to check the suspension system. If you bounce or push on the tub by hand and feel excessive movement or hear the tub knock against the cabinet even with a properly distributed load, worn suspension rods are a likely cause rather than a leveling or load-balance issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, materials, and mounting configuration of the original W11130362 suspension rod kit used in compatible Whirlpool, Maytag, Kenmore, and Crosley top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11205048 Washer Genuine OEM Water Valve Fits select Kenmore, Maytag, Whirlpool top load washer models.  Replaces Part Numbers: W11205048, 4814041, W10843663, AP6327347, PS12349203. Description:  This Water Inlet Valve is a Genuine OEM part for specific Whirlpool washing machine models. This valve controls the flow of water into the washer, allowing it to fill with the correct amount of water during the wash and rinse cycles.  Over time, the water inlet valve can become clogged with debris, develop electrical issues, or wear out, leading to problems with the water flow. Causes of a bad water inlet valve include mineral buildup from hard water, internal component failure, or damage to the valve body.

Read more less

W10467289 Washer Genuine OEM Temperature Sensor Replaces Part Numbers: WPW10467289, W10467289, 2629420, 8181705, 8182291, 8540225, 8540226, W10176658, W10176659, OEM18065663, AP6021886,, PS11755214. Description: This Water Temperature Sensor is a Genuine OEM part for specific Kenmore, Whirlpool washing machine models. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8318084 Washer Lid Switch Replaces WP8318084 The XPARTCO 8318084 is an aftermarket replacement lid switch assembly compatible with a wide range of Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, Magic Chef, Crosley, and Admiral direct-drive top-load washing machines. The lid switch is a safety component located under the control panel at the top rear left corner of the washer — it detects whether the lid is open or closed and prevents the washer from spinning and agitating when the lid is open. When the lid is closed, the switch signals the control that it's safe to operate. Without a functioning lid switch, the washer may refuse to start, won't spin, won't agitate, won't drain, or stop advancing through its cycle. Gray and white plastic housing. Electrical rating: 125–250V, 50–60Hz, 1/2 HP. Dimensions: 3"L x 2"W x 1-15/16"H. Features 3 flat terminals that the wiring harness plugs onto, plus a green grounding wire. It directly replaces WP8318084, WP8318084VP, AP3180933, AP6012742, AH886960, EA886960, EAP11745957, ES8084, TJ90ES8084, PD00002474, PN8318084, PS886960, PS11745957, and 11480-61. This is one of the most widely used lid switches across the Whirlpool direct-drive platform, fitting hundreds of top-load washer models. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 8318084 Washer Lid Switch fixes Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, and Crosley direct-drive top-load washers that won't start, won't spin, won't agitate, won't drain, won't advance through the cycle, or have a burning smell from the motor. Gray/white, 125–250V, 50–60Hz, 1/2 HP. 3"L x 2"W x 1-15/16"H. 3 flat terminals + green grounding wire. Replaces WP8318084, WP8318084VP, AP3180933, AP6012742, AH886960, EA886960, EAP11745957, ES8084, TJ90ES8084, PD00002474, PN8318084, PS886960, PS11745957. Classic symptom: won't spin but may still fill. Common Problems This Part Fixes Washer won't spin — the classic lid switch failure symptom on direct-drive washers Washer won't start at all — control not detecting a closed lid Washer won't agitate — lid switch blocking motor engagement Washer won't drain — drain is tied to the spin/lid interlock on many models Wash cycle not advancing past fill — stuck waiting for lid-closed signal Burning smell from the motor area — motor stalling because the switch won't engage Lid won't close properly or switch doesn't activate when lid is shut Intermittent operation — washer sometimes works, sometimes doesn't, depending on lid position Lid switch visibly cracked, broken, or with a failed lever Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WP8318084, 8318084, WP8318084VP, ES8084, TJ90ES8084, 045903691979, 11480-61, PN8318084, AWP48129, EAP11745957, 11480-61, PN8318084, PD00002474, AP6012742, PS11745957. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select direct-drive top-load washing machines from the following brands: Whirlpool top-load washers — direct-drive models (including 1CLBR, 1CLSQ, 1CLSR, LSQ, LSR, LSW, WTW series and many more) Kenmore and Kenmore Elite top-load washers (select Whirlpool-built models — 110-series) KitchenAid top-load washers (select models) Roper top-load washers (select models) Estate top-load washers (select models) Maytag top-load washers (select Whirlpool-built models) Amana top-load washers (select models) Magic Chef top-load washers (select models) Crosley top-load washers (select models) Admiral top-load washers (select models) Note: This lid switch is specific to direct-drive top-load washers on the Whirlpool platform. It is NOT the same switch used on stacked laundry centers, washer/dryer combos, or front-load washers — those use different lid switch or door lock part numbers. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-drive washer lid switch assembly — detects whether the lid is open or closed and prevents spinning, agitating, and draining when the lid is open Resolves "won't start," "won't spin," "won't agitate," "won't drain," "cycle not advancing," and "burning smell" symptoms caused by lid switch failure Gray and white plastic housing — durable construction Electrical rating: 125–250V, 50–60Hz, 1/2 HP Dimensions: 3"L x 2"W x 1-15/16"H 3 flat terminals that the wiring harness plugs onto, plus a green grounding wire Located under the control panel on the top rear left corner of the washer One of the most widely used lid switches on the Whirlpool direct-drive platform — fits hundreds of top-load washer models Replaces WP8318084, WP8318084VP, AP3180933, AP6012742, AH886960, EA886960, EAP11745957, ES8084, TJ90ES8084, PD00002474, PN8318084, PS886960, PS11745957, and 11480-61 Compatible with Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, Magic Chef, Crosley, and Admiral direct-drive top-load washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 8318084 OEM Part Number WP8318084 Part Type Washer Lid Switch Assembly (Direct-Drive Top-Load) Condition Aftermarket Replacement Application Direct-Drive Top-Load Washing Machines (Whirlpool platform) Voltage 125–250V Frequency 50–60 Hz Motor Rating 1/2 HP Dimensions 3"L x 2"W x 1-15/16"H Terminals 3 flat terminals + green grounding wire Color Gray / White Material Plastic housing Location Under the control panel, top rear left corner Compatible Brands Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, Magic Chef, Crosley, Admiral Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The lid switch is located under the control panel at the top rear left corner of the washer. To access it, you'll need to remove the control panel: on most direct-drive washers, use a putty knife or flat-blade screwdriver to release the spring clips at the bottom edge of the control panel (typically two clips), then flip the control panel up and back on its hinges to rest against the wall behind the washer. You should now see the lid switch mounted on the left side with two screws. Photograph the wiring before disconnecting. Unplug the wiring harness from the 3 flat terminals on the old lid switch — note how the harness connects. Remove the two mounting screws holding the old switch in place. Also disconnect the green grounding wire (it's attached separately with its own screw). Remove the old switch. Install the new 8318084 switch in the same position using the two mounting screws. Reconnect the green grounding wire with its screw. Plug the wiring harness back onto the 3 flat terminals, matching your photos. Flip the control panel back down and press it into place until the spring clips snap. Plug the washer back in and test by closing the lid and running a cycle — confirm the washer starts, agitates, spins, and drains. Tools needed: Phillips screwdriver, putty knife or flat-blade screwdriver (for spring clips), work gloves. Frequently Asked Questions My washer won't spin but still fills — is the lid switch the problem? Very likely, yes. On direct-drive top-load washers, the lid switch is a safety interlock that prevents spinning and agitating when the lid is open. When the switch fails, the control never receives the "lid closed" signal, so it blocks the spin (and often the agitate and drain) as a safety measure — but filling still works because that doesn't require the lid interlock. If your washer fills but won't advance past that point, or agitates but refuses to spin, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is pressed — a working switch shows continuity when activated. Why would a bad lid switch cause a burning smell? This happens when the motor tries to engage but the lid switch isn't signaling correctly, causing the motor to stall or repeatedly attempt to start without completing the cycle. A stalling direct-drive motor generates heat that produces a burning smell. If you notice a burning smell AND the washer isn't spinning or agitating properly, check the lid switch first — it's far more likely (and cheaper) than a motor failure. If the burning smell continues after replacing the switch, have the motor and motor coupling inspected by a technician. What's the difference between 8318084 and WP8318084? These are the same lid switch across production revisions. 8318084 was the original part number and WP8318084 is the Whirlpool-era part number (with the "WP" prefix Whirlpool adopted). WP8318084VP is a variant packaging code. All are physically and functionally identical — if your washer's parts diagram shows any of these numbers, this listing is the correct replacement. The many additional cross-references (AP3180933, AP6012742, ES8084, PS886960, PS11745957, etc.) are catalog identifiers from various parts distributors for the same switch. Does this fit my stacked laundry center or front-load washer? No — the 8318084 is specifically designed for standalone direct-drive top-load washers on the Whirlpool platform. Stacked washer/dryer laundry centers use different lid switch part numbers (such as the 3355806 for Whirlpool thin twin units), and front-load washers use door lock assemblies instead of lid switches. Always search by your appliance's model number to confirm the correct part. Contact our support team with your model number if you're unsure which switch fits your machine. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (125–250V, 50–60Hz, 1/2 HP), dimensions (3"L x 2"W x 1-15/16"H), 3-flat-terminal configuration, grounding wire, and lid-detection function of the original WP8318084 lid switch used in compatible Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, and related direct-drive top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11688994 Washer Genuine OEM Water Valve Single water inlet valve, hot Replaces Part Numbers: W11688994, W11316255, W11036928, W11486360, AP7218602, PS17216729. Description: This Water Inlet Valve is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals. 

Read more less

WH23X10026 Washer Genuine OEM Drain Pump Description: The GE drain pump assembly is an OEM replacement part responsible for removing wastewater, including dirty water and detergent residue, from the washer's tub during the drain cycle. This pump assembly consists of a motor and an impeller, which removes dirty water through the drain hose and out of the appliance. This part ensures that the washing machine efficiently drains water, allowing for the completion of the laundry cycle. Replaces Part Numbers: WH23X10028, WH23X10026, WH23X10037, AP4324598, AH1766031, EA1766031, PS1766031.   California Residents only WARNING: California’s Proposition 65 

Read more less

XPARTCO AJU75152602 Washer Water Inlet Valve The XPARTCO AJU75152602 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the larger-capacity WT7 series — including the WT7060, WT7100, WT7150, WT7155, WT7250, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, and WT7900 series. The water inlet valve is a multi-port solenoid valve mounted on the back of the washer that controls the flow of hot and cold water into the tub and dispenser compartments during fill and rinse cycles. When any valve port fails, the washer may not fill at all, fill too slowly, fill with the wrong water temperature, overfill, or leak from the valve body. This valve assembly directly replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681. It includes two integrated inlet screens to filter debris from the supply lines. Installs in 15–25 minutes with basic hand tools. Note: the AJU75152602 is for the WT7xxx larger-capacity LG top-load series — it is not the same valve as the AJU75152601, which is used on the earlier and smaller-capacity WT1xxx through WT5xxx series. Verify your model number before ordering. Quick Answer The XPARTCO AJU75152602 Washer Water Inlet Valve fixes LG WT7xxx-series top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or leak from the valve. Includes 2 inlet screens. Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, PD00060681. Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore (LG-built). Note: not the same as AJU75152601 — different model series. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection Water dripping into the tub between cycles — valve not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: AJU75152602, 4873914, 5221EA1008S, U8EONG(9F), IV-248-103, PD00060681, FIX12580369, ALG53788, AP6335382, PS12580369, DC12V 6W, IV-248-103, U8EONG(9F). If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG WT7 series top-load washers and related Kenmore models: LG WT7060CV, WT7060CW LG WT7100CW LG WT7150CW, WT7155CW LG WT7250CW LG WT7300CV, WT7300CW LG WT7305CV, WT7305CW LG WT7400CV, WT7400CW LG WT7405CV, WT7405CW LG WT7800CV, WT7800CW LG WT7880HWA LG WT7900HBA Kenmore 31452 and select LG-built Kenmore models Important — AJU75152602 vs AJU75152601: These are two different valves for different LG washer generations. The AJU75152602 is for the larger-capacity WT7xxx series. The AJU75152601 is for the earlier and smaller-capacity WT1xxx through WT5xxx series. They are not interchangeable. Always verify your model number before ordering. Key Features Multi-port solenoid valve — controls hot water, cold water, and dispenser ports to deliver the correct water temperature and volume for each cycle phase Includes two integrated inlet screens — filter debris and mineral deposits from the supply lines before they reach the valve seat ABS plastic and stainless steel construction — durable and resistant to mineral buildup and corrosion Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681 Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore LG-built models For WT7xxx series only — not the same as AJU75152601 (WT1xxx–WT5xxx series) Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number AJU75152602 Part Type Washer Water Inlet Valve Assembly (Multi-Port) Condition Aftermarket Replacement Application LG WT7xxx Series Top-Load Washers Material ABS plastic / Stainless steel Kit Includes Valve assembly + 2 integrated inlet screens Note WT7xxx series only — not interchangeable with AJU75152601 (WT1xxx–WT5xxx) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose positions before disconnecting. Disconnect the two external supply hoses from the valve inlet ports. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from each solenoid port. Unscrew the mounting screws and remove the old valve. Install the new AJU75152602 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the documented positions. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers. Frequently Asked Questions What is the difference between AJU75152602 and AJU75152601? These are two different water inlet valve assemblies for different generations of LG top-load washers. The AJU75152601 (which also replaces AJU73213301 and 5221EA1008F) is used on LG's earlier and smaller-capacity top-load washers in the WT1xxx, WT4xxx, and WT5xxx series. The AJU75152602 (which replaces 5221EA1008S) is for LG's larger-capacity WT7xxx series. Despite appearing similar, they have different port configurations and are not interchangeable. Always verify your specific model number before ordering. How do I know if the water inlet valve has failed? Common signs are the washer not filling, filling only on one temperature setting, overfilling, dripping between cycles, or leaking from the valve area. Before replacing the valve, check that both supply valves are fully open and the hoses are not kinked. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed. Also inspect and clean the inlet screens inside the supply port openings — mineral-clogged screens can restrict flow enough to cause the same symptoms as a failed valve. What are the two inlet screens included with the valve? The two mesh screens that come with the AJU75152602 install inside the hot and cold water inlet ports of the valve. They catch sediment, mineral particles, and debris from the household water supply before they can reach the solenoid valve seats. Installing fresh screens along with the new valve helps extend the valve's service life, especially in areas with hard water. If the previous valve failed due to mineral buildup rather than an electrical fault, cleaning the supply hoses before installation is also recommended. My LG WT7300CW is only filling with cold water — is this the valve? Filling with only cold water on a warm or hot cycle is a classic sign that the hot water solenoid coil on the inlet valve has failed. Each temperature port is controlled by its own independent solenoid — when the hot solenoid fails, only the cold port opens. Before replacing the valve, also confirm that the household hot water supply valve is fully open and that hot water is reaching the back of the washer in the supply hose. If hot water supply is confirmed and the cold-only fill persists, replace the AJU75152602 valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration and specifications of the original AJU75152602 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less