Search results for "washer knob"

XPARTCO WH01X29528 Washer Door Lock The XPARTCO WH01X29528 is an aftermarket replacement door lock assembly compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Monogram front-load washing machines — as well as select GE UltraFast 2-in-1 combo washer/dryer units. The door lock is a safety mechanism mounted at the front of the washer where the door closes — it automatically engages when the door is shut, securing it closed for the entire wash and spin cycle so water and detergent can't spill out and cause injury. It also signals the control board that the door is safely locked, which is what allows the washer to start filling and running. When the door lock fails, the washer typically won't start, won't lock the door, stops mid-cycle, or throws a door-related error code. Rated 120 VAC, 60Hz, 16A. Failure usually comes from physical damage or normal wear over time. As a direct replacement for the GE WH01X29528, it also replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 (additional production markings: ITW 12070-71, V13305, 0024000128GE). Installation is straightforward with no wiring modifications — remove the old lock and install the new one, typically in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO WH01X29528 Washer Door Lock fixes GE, GE Profile, Café, and Haier front-load washers (and GE UltraFast 2-in-1 combo units) where the door won't lock or unlock, the washer won't start, the washer stops mid-cycle, the door feels loose or won't seal, or a door-latch error code appears. 120 VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, PS12749276, PD00060769, 4958749. Compatible with GE GFW510, GFW550, GFW650, GFW850, PFW870, PFW950, PFQ97 series front-load washers. No wiring modifications — installs in 10–15 minutes. Common Problems This Part Fixes Washer door won't lock at the start of the cycle Washer won't start — control board not detecting a locked door Washer door won't unlock at the end of the cycle Washer stops mid-cycle due to a door lock fault Door-latch related error code displayed on the control panel Door feels loose or doesn't seal properly Excessive noise and shaking while the washer is running (related to a door not securing properly) Intermittent locking — washer sometimes starts, sometimes doesn't Door lock assembly visibly broken, cracked, or with a failed latch Burning/electrical smell or humming from the door lock area (failed lock solenoid) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AGE26402, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, OEM20955948, V13305, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock assembly is compatible with select front-load washing machines and combo washer/dryer units from the following brands: GE front-load washers — GFW510 series (GFW510SCN0WW–SCN5WW, GFW510SCV0WW) GE front-load washers — GFW550 series (GFW550SPN0DG–SPN3DG, GFW550SPR0RS/SPR3RS/SPR4RS/SPR5RS, GFW550SSN0WW–SSN5WW) GE front-load washers — GFW650 series (GFW650SPN0SN–SPN4SN, GFW650SSN0WW–SSN4WW) GE front-load washers — GFW655 series (GFW655SPV0DS, GFW655SSV0WW) GE front-load washers — GFW850 series (GFW850SPN0DG–SPN5RS all DG/RS variants, GFW850SSN0WW–SSN5WW) GE Profile front-load washers — PFW870 series (PFW870SPV0RS, PFW870SSV0WW), PFW950 series (PFW950SPT0DS/SPT1DS/SPT2DS) GE Profile combo units — PFQ97HSPV0DS (UltraFast 2-in-1 combo washer/dryer) GE Café, Haier, Hotpoint, RCA, Monogram — select front-load models using the same door lock Sears Kenmore and Crosley — select GE-built front-load models Always verify your appliance model number before ordering. The WH01X29528 fits the specific models listed — please double-check your model number. Contact our support team if you're unsure. Key Features Door lock and switch assembly — locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Prevents the door from being opened mid-cycle, keeping water and detergent safely contained Resolves "won't lock," "won't unlock," "won't start," "stops mid-cycle," and door-latch error codes when caused by a failed lock Rated 120 VAC, 60Hz, 16A — correct electrical specifications for compatible GE front-load washers Integrates with the washer's main control board, door switch, and load detection system Durable, moisture-resistant materials resist deformation, wear, and short circuits for long service life No wiring modifications required — direct-fit replacement using the original connector Replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 Compatible with GE GFW510/GFW550/GFW650/GFW850, PFW870/PFW950, and PFQ97 series front-load washers and UltraFast combo units, plus select Café, Haier, Hotpoint, RCA, Monogram, Kenmore, and Crosley GE-built models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPWH01X29528 Part Type Washer Door Lock and Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers & Combo Washer/Dryer Units (GE platform) Voltage 120 VAC Frequency 60 Hz Amperage 16A Additional Production Markings ITW 12070-71, V13305, 0024000128GE Function Locks door during wash/spin; signals control board door is secure Location Front of washer at the door opening Compatible Brands GE, GE Profile, Café, Haier, Hotpoint, RCA, Monogram, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, you may need to access the manual release. Peel back the rubber door boot/gasket from the front panel edge near the lock to expose the door lock assembly — on some models this requires releasing the spring-loaded wire clamp that secures the boot with needle-nose pliers. Photograph the wire harness connection before disconnecting anything. Remove the mounting screws holding the door lock assembly to the front panel. Reach in and pull the assembly out through the door opening far enough to access the wire connector. Disconnect the wire harness plug from the old assembly (no wiring modifications are needed — it's a direct plug connection). Snap the new WH01X29528 assembly onto the wire harness plug until it clicks firmly, position it in the front panel opening, and secure it with the mounting screws. Press the rubber door boot back into its groove and reinstall the spring-loaded wire clamp if applicable. Restore power and test by closing the door and starting a cycle — confirm the door locks, the washer runs, and the door unlocks at the end. Tools needed: Phillips screwdriver, needle-nose pliers, work gloves. Frequently Asked Questions My GE washer won't start and shows a door error — is this the part? Very likely, yes. GE front-load washers won't start unless the control board receives confirmation from the door lock that the door is closed and locked — it's a safety interlock. When the door lock fails, the washer either won't lock the door, won't start, or displays a door-related message on the panel. If your door appears to close normally but the washer won't begin the cycle (or stops shortly after starting), the door lock is the most common cause. Replacing the WH01X29528 typically resolves it. If you've already replaced the door lock and the problem persists, the issue may be the main control board instead. I replaced the door lock and it worked briefly, then failed again — what's wrong? If a new door lock works for a short time (seconds to minutes) and then the washer goes back to showing a door error, the problem may not be the lock itself but the main control board that powers and monitors it. A control board with a failing door-lock circuit can damage or fail to properly drive the lock, causing repeated symptoms even after replacing the lock. Some customers report an electrical smell or humming from the lock in these cases. If you've replaced the door lock (especially more than once) and the door error returns, the main control board is the next component to investigate. Contact our support team with your model number for the correct control board part. Does this fit the GE UltraFast 2-in-1 combo washer/dryer? Yes — the WH01X29528 is used on select GE UltraFast 2-in-1 combo washer/dryer units (such as the PFQ97HSPV0DS) in addition to standalone GE front-load washers. The combo units use the same door lock design as the front-load washers in the GFW/PFW families. As always, confirm your specific model number against the compatibility list before ordering, since GE uses different door locks across different washer generations. How do I open the door if it's stuck locked and the washer won't run? If the door is stuck in the locked position because of a failed lock, first make sure there's no water in the drum (run or complete a drain cycle if possible). Then unplug the washer and wait a few minutes — some GE models release the lock after power is removed. If it's still stuck, most front-load washers have a manual release mechanism accessible from behind the lower kick panel at the front of the machine — a tab or cord you pull to manually disengage the lock. Consult your model's manual for the manual release location. Once the door is open, you can proceed with replacing the lock. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable, moisture-resistant materials to match the electrical specifications (120 VAC, 60Hz, 16A), connector configuration, mounting, and door-locking function of the original WH01X29528 door lock used in compatible GE, GE Profile, Café, Haier, and related front-load washers and combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8181651 Washer Door Striker  Replaces Part Numbers: WP8181651, 8181651, 906446, AP6011711, PS11744910. Description: This Door Strike is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

Genuine OEM WH23X35712 Washer Water Valve The Genuine OEM GE WH23X35712 is an electromagnetic (solenoid) water valve for GE, Hotpoint, and Kenmore washers. The valve connects your home's water supply to the washer. It opens when the control energizes it to let water into the washer and shuts off to prevent overfilling. When it fails, the washer may not fill, may fill intermittently, or may fill slowly or weakly. This is the original GE part. GE washers use several different water valves that look alike, so confirm the part number against your model before ordering. Quick Answer The Genuine OEM WH23X35712 Water Valve fixes a GE, Hotpoint, or Kenmore washer that won't fill, fills intermittently, or fills slowly. It is a sealed on/off solenoid valve. Classic symptom: the cycle starts but little or no water comes in, and the supply taps and hoses are clear. Common Problems This Part Fixes Washer won't fill with water Intermittent filling during the cycle Slow or weak fill Valve that leaks or doesn't shut off properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water valve directly replaces the following part number: WH23X35712, 4984177, AGE26168, AP7211666, EAP17139268, PD00089992, PS17139268 No other GE part numbers were confirmed for this valve. Other GE washer valves with similar numbers, such as WH23X29553, are different parts. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This valve is listed for GE, Hotpoint, and Kenmore washers. GE-family washers sold as General Electric, Hotpoint, RCA, and Kenmore Note: We could not confirm a model list for this valve, so compatibility is stated by brand only. GE makes several look-alike washer valves that differ in coil count and connections. Enter your model number at checkout or contact our support team to verify fit before ordering. Key Features Genuine OEM GE electromagnetic (solenoid) water valve Sealed on/off valve that controls water flow into the washer Resolves no-fill, intermittent-fill, and slow-fill problems Listed for GE, Hotpoint, and Kenmore washers Product Specifications Part Number WH23X35712 OEM Part Number WH23X35712 Part Type Washer Electromagnetic (Solenoid) Water Valve Condition Genuine OEM Application GE, Hotpoint & Kenmore Washers Installation Notes ⚠️ Unplug Power and Shut Off the Water Unplug the washer and turn off the water supply before beginning. Wear work gloves, and have a towel and shallow pan ready for water left in the hoses. Follow your model's service guide to reach the valve, note the position of each wire connector and hose, and disconnect them. Handle the new valve by its body and avoid stressing the electrical connectors or the inlet and outlet fittings. Inspect the hoses and fittings, replace any worn seals, then reconnect everything and check for leaks with the water on. Frequently Asked Questions My washer won't fill. Is this the part I need? A failed water valve is a common cause. First check that the water supply taps are fully open and that the inlet screens at the hose connections aren't clogged. If both are fine and the washer still fills slowly or not at all, the valve is a likely cause. What does this valve do? It is an on/off solenoid valve. It opens when energized to let water in and closes to stop the flow and prevent overfilling. Can I use a different GE washer valve? Not unless your model's parts diagram calls it out. GE makes several valves that look alike but differ in coil count and connections. Use the number your model calls out, or contact our support team to confirm. Will this fit my washer? It is listed for GE, Hotpoint, and Kenmore washers, but we could not confirm a model list. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WB03X24818CM Range Control Knob Burner Knob. Fits specific GE Gas Range models. Replaces Part Numbers: WB03X24818, AP5989029, PS11729081. Description: This Range Knob is a replacement part for specific GE ranges and oven models. It is used to control the temperature and settings of the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W11165546 Washer Water Inlet Valve The XPARTCO W11165546 is an aftermarket replacement washer water inlet valve assembly compatible with Maytag Bravos XL, Whirlpool Cabrio, Kenmore 700-series, and related Whirlpool-platform HE top-load washers. This 4-solenoid assembly controls the flow of hot and cold water from the household supply lines into the washer tub and dispenser compartments. It includes an integrated thermistor on the center outlet that monitors incoming water temperature and communicates it to the control board so the washer can achieve the correct wash temperature. When the valve fails — or when a single solenoid coil burns out — the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. Rated 120V, 60Hz, with 2 inlet ports and 3 outlet ports, this assembly measures 5-3/8"L x 4-1/4"W x 3"H. The valve body may be blue or green in color depending on production run — both are functionally identical. It is compatible with 1/2" ID supply hoses. It directly replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, WV5546, 33090105, 4545980, AP6284346, EAP12348013, PD00037668, and PS12348013. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO W11165546 Washer Water Inlet Valve fixes Maytag Bravos XL and Whirlpool Cabrio/WTW HE top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. 4-solenoid valve with thermistor. 120V/60Hz. 2 inlet / 3 outlet ports. 5-3/8"L x 4-1/4"W x 3"H. Compatible with 1/2" ID supply hoses. Replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, 33090105, 4545980, AP6284346, PS12348013. Common Problems This Part Fixes Washer not filling with water — error code F8E1, LF, or LO FL displayed Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection — thermistor failed Water dripping into the tub between cycles — valve not closing completely Water leaking from the back of the washer near the valve Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: W10839828, 33090105, 4545980, W10599423, W10758828, W11096267, W11165546VP, AP6284346, AWP43457, EAP12348013, PD00037668, PS12348013. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select HE top-load washers from the following brands and series: Maytag top-load washers — Bravos XL series (MVWB765FW0, MVWB765FW1, MVWB765FW2, MVWB765FW3, MVWB765FC1, MVWB765FC2, MVWB766FW0, MVWB766FW1, MVWB835DW1, MVWB835DW2, MVWB835DW3, MVWB835DW4, MVWB855DC2, MVWB855DC3, MVWB865GC0, MVWB865GW0, MVW6230HW2, MVW7230HW0, MVW7232HW0 and related models) Whirlpool top-load washers — Cabrio / WTW series (WTW7500GC0, WTW7500GW0, WTW8500DC2, WTW8500DC4, WTW8500DC5, WTW8500DR4, WTW8500DR5, WTW8500DW4, WTW8500DW5, WTW8700EC1, 7MWTW8500EC2 and related models) Kenmore / Sears top-load washers — 700 series (11028132410, 11028132411, 11028132412, 11028132413, 11028133410, 11028133411, 11029132411, 11029133410 and related models) Crosley top-load washers (select models) Note: The valve body color may be blue or green depending on production run — both are functionally identical. This valve is for HE top-load washers only. Always verify your model number before ordering. Key Features 4-solenoid valve assembly — controls hot water, cold water, and additional dispenser/recirculation ports to fill the tub with the correct temperature water for each cycle Integrated thermistor on center outlet — monitors incoming water temperature and communicates with the control board to achieve the correct wash temperature Resolves F8E1, LF, and LO FL error codes on compatible Maytag and Whirlpool HE top-load washers Rated 120V, 60Hz — correct electrical specifications for compatible models Dimensions: 5-3/8"L x 4-1/4"W x 3"H 2 inlet ports, 3 outlet ports — compatible with 1/2" ID supply hoses Valve body color (blue or green) varies by production run — functionally identical Replaces W10599423, W10758828, W10839828, W11096267, and W11165546VP Compatible with Maytag Bravos XL MVWB series, Whirlpool WTW7xxx/WTW8xxx, Kenmore 700 series, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number W11165546 Part Type Washer Water Inlet Valve Assembly (4-Solenoid with Thermistor) Condition Aftermarket Replacement Application HE Top-Load Washers — Bravos XL, Cabrio, WTW series Solenoids 4-coil (hot, cold, and additional ports) Thermistor Integrated on center outlet — monitors water temperature Voltage 120V AC Frequency 60 Hz Dimensions 5-3/8"L x 4-1/4"W x 3"H Inlet Ports 2 (hot and cold) Outlet Ports 3 Supply Hose ID 1/2 inch Color White / Blue or Green (production run dependent — functionally identical) Error Codes Resolved F8E1, LF, LO FL Compatible Brands Maytag, Whirlpool, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose routing before disconnecting. Disconnect the two external supply hoses from the valve inlet ports using pliers to loosen any stuck connections. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from all solenoid coils and the thermistor. Unscrew the mounting hardware and remove the old valve. Install the new W11165546 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the same positions as documented. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers, channel-lock pliers for stubborn hose connections. Frequently Asked Questions What do error codes F8E1, LF, and LO FL mean on Maytag and Whirlpool washers? F8E1 (also displayed as LF or LO FL on some models) indicates a long fill fault — the washer was unable to fill to the required water level within the expected time. The most common causes are a failed water inlet valve (solenoid coil burned out or valve seat clogged), low household water pressure, or kinked supply hoses. Before replacing the valve, confirm both supply valves are fully open, the supply hoses are not kinked, and household water pressure is adequate. If all supply conditions are good and the error persists, the water inlet valve is the most likely cause. What is the difference between W11165546 and W11096267? These are the same water inlet valve assembly. W11096267 was an earlier version, and W11165546 is the current updated part number. The W10599423 and W10758828 are also cross-references to earlier versions of this same valve. The W11165546VP is the Whirlpool factory-packaged version. All of these are covered by this aftermarket replacement. Why does this valve have 4 solenoids? Modern HE top-load washers like the Maytag Bravos XL and Whirlpool Cabrio use multiple water paths for different wash functions — hot water inlet, cold water inlet, a bleach dispenser port, and a fabric softener/recirculation port. Each path is controlled by its own independent solenoid coil on the same valve assembly. This allows the control board to independently open any combination of ports needed for a given cycle phase. When any single solenoid coil fails, only the function controlled by that coil is affected — which is why the washer might fill normally with cold water but not hot, or fail to activate only one dispenser. Does the valve color (blue vs green) matter? No — the blue and green valve body colors are simply the result of different production runs at the factory. Both colors are the same part number (W11165546) with identical electrical specifications, port configuration, thermistor, and dimensions. Either color will function correctly in your washer. There is no functional difference between the two. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with 4 solenoid coils and an integrated thermistor to match the electrical specifications and port configuration of the original W11165546 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X24697 Washer Drive Belt The XPARTCO WH01X24697 is an aftermarket replacement drive belt for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This belt connects the drive motor to the drive system, transmitting rotation to spin the basket during the wash and spin cycles. Measures approximately 21" long, made of durable, flexible rubber engineered to reduce slipping and squeaking while withstanding regular tension and wear. Over time, the belt stretches, cracks, or breaks from age and normal use. If your washing machine is making unusual noise, not spinning correctly, or the basket isn't moving, this drive belt may be the cause. It directly replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. Quick Answer The XPARTCO WH01X24697 Washer Drive Belt fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers with unusual noise, a basket that won't spin correctly, or a basket that isn't moving at all. Approximately 21" long. Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. Not the same as the similarly-numbered WH01X24180 or WH01X27538 belts, which are separate parts used on other GE/Hotpoint models — confirm your exact part number before ordering. Common Problems This Part Fixes Basket not spinning or not moving at all Unusual noise during operation, including squeaking Basket slipping or spinning inconsistently Wash cycle running without proper agitation or spin Belt visibly stretched, cracked, or broken Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WH01X24697, 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as GTW220ACK1WW, GTW220ACK2WW, GTW220ACK3WW, GTW330ASK0WW, GTW330ASK1WW, GTW330ASK2WW, GTW460AMJ1WW, GTW460AMJ3WW, GTW460AMJ4WW, GTW460ASJ1WW, GTW460ASJ3WW, GTW460ASJ4WW, GTW460ASJ5WW, GTW460ASJ6WW, GTW460ASJ7WW, HTW200ASK0WW, HTW200ASK1WW, HTW200ASK2WW, HTW240ASK0WS, HTW240ASK1WS, and HTW240ASK2WS. Note — not the same as WH01X24180 or WH01X27538: These are separate GE/Hotpoint drive belts with their own cross-reference sets, used on different models. The similar numbering makes them easy to confuse. Always verify your exact part number before ordering. Contact our support team with your model number if you're unsure which belt your washer needs. Key Features Aftermarket replacement drive belt — connects the drive motor to the drive system to spin the basket Resolves "won't spin," "unusual noise," and "basket not moving" symptoms caused by belt failure Approximately 21" long Durable, flexible rubber construction engineered to reduce slipping and squeaking Direct drop-in replacement matching the original length and profile Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair with basic tools Product Specifications Part Number WH01X24697 OEM Part Number WH01X24697 Part Type Washer Drive Belt Condition Aftermarket Replacement Length Approx. 21" Material Rubber Function Connects the drive motor to the drive system to spin the basket Repair Difficulty Easy to Moderate Quantity 1 drive belt Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel of the washer using a socket wrench set, taking out the securing screws and carefully lifting the panel away. Locate the drive belt near the motor, at the bottom of the washer. Use a screwdriver to loosen the tensioner, then gently slide the old belt off the pulleys. Fit the new WH01X24697 belt around the pulleys in the same path as the old one, then re-tension it with the tensioner. Reinstall the back panel and secure its screws. Restore power and run a test cycle to confirm the basket spins smoothly with no unusual noise. Tools needed: socket wrench set, screwdriver, work gloves. Frequently Asked Questions My washer's basket isn't spinning. Is this the belt I need? Yes, this is one of the most common symptoms of a failed drive belt. Since this belt is what transmits rotation from the drive motor to the basket, a stretched, cracked, or broken belt can leave the motor running while the basket doesn't spin correctly or at all. Is this a difficult repair? No, it's a straightforward repair for a confident DIYer with basic tools. It involves removing the back panel to access the belt near the motor, loosening the tensioner, and swapping the belt — no specialized skills required. Is this the same as WH01X24180 or WH01X27538? No, these are separate GE/Hotpoint drive belts with their own distinct cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old belt rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the length, material, and pulley fit of the original WH01X24697 drive belt used in compatible GE, Hotpoint, Haier, Monogram, and Café top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly The AAN73209838 is a genuine LG OEM combined drain pump and cabinet base assembly for LG washers. This assembly bundles the washer's drain pump — which pumps water out of the drum and through the drain hose at the end of each cycle — together with the cabinet base structure it's mounted to. Because these two components ship together as one assembly, replacing this part addresses both the drain pump function and the base structure it sits in at the same time. Common causes of failure include a worn or jammed drain pump motor, or physical damage or corrosion to the cabinet base itself over years of use. A failing assembly typically shows up as the washer failing to drain, unusual noise during the drain phase, or water leaking from underneath the unit. Quick Answer The AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly fixes LG washers that won't drain, make unusual noise during the drain phase, or are leaking water from underneath the unit. Combined drain pump and cabinet base assembly. This is a larger, heavier assembly than a standalone drain pump — installation involves more disassembly than a simple pump swap. Common Problems This Part Fixes Washer not draining — standing water left in the tub after a cycle Unusual noise during the drain phase of the cycle Water leaking from underneath the washer Cycle stalling or failing to advance past the drain step Visible damage or corrosion to the cabinet base structure Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers AAN73209838, 4873470, 4985882, AHA75673401, AP6991753, AP6991765, EAP12580277, EAP16222263, FIX16222263, PS12580277, PS16222263, ALG51685, PD00091778 We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This drain pump and cabinet base assembly is compatible with select LG top-load washers, including model numbers such as WT7060CW, WT7100CW, WT7250CW, WT7300CV, T1780WFHT, and T1789EFH5T/T1789EFH5U/T1789EFHT/T1789EFHKD variants. Note: This is a combined assembly, not a standalone drain pump — if your washer only needs the pump replaced and the cabinet base is intact, ask our support team whether a standalone pump option is available for your model before ordering this larger assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified pump and base assembly Combined drain pump and cabinet base assembly in a single part Resolves "won't drain," "noisy drain phase," and "leaking underneath the washer" symptoms Direct drop-in replacement — matches the original mounting and hose connections Compatible with a range of LG top-load washer models Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AAN73209838 Part Type Washer Drain Pump & Cabinet Base Assembly Condition Genuine OEM Brand LG Application Top-Load Washers Function Pumps water from the drum through the drain hose; provides the cabinet base structure Repair Difficulty Moderate to Hard — larger assembly than a standalone pump Quantity 1 combined assembly Compatible Brand LG Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Remove Standing Water First Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Because this is a combined pump and cabinet base assembly rather than a standalone pump, access typically requires tipping the washer back or removing more of the cabinet than a simple pump swap — check your model's service diagram for the exact disassembly sequence, since it varies by model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old assembly, remove the fasteners securing it to the washer frame, and carefully remove it, noting how the base supports the rest of the cabinet. Install the new AAN73209838 assembly in the same position, reconnect the drain hose connections securely, reconnect the electrical connector fully, and secure all mounting fasteners. Reassemble the cabinet in reverse order, restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, socket set, pliers, towels or a small cup for removing standing water, work gloves. Frequently Asked Questions Do I need this whole assembly, or is there a smaller drain pump option for my model? Some LG washer models offer a standalone drain pump as a separate, smaller part, while others require this combined pump-and-base assembly because the two are integrated on that particular platform. Check with our support team using your model number to confirm whether a standalone pump is available for your washer before ordering this larger assembly, since it can save you time and cost if a smaller part fits your model. Why is this repair more involved than a typical drain pump replacement? Because this part includes the cabinet base structure along with the pump, accessing and replacing it typically involves more disassembly than swapping a standalone pump alone — you're not just disconnecting a pump, you're also working with part of the washer's supporting frame. Budget more time for this repair than you would for a simple pump-only replacement, and consider having a second person help support the cabinet during removal and installation. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, hose connections, and cabinet base mounting configuration of the assembly originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

285805 Genuine OEM Whirlpool Washer Water Inlet Valve The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves. This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517. Quick Answer The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer won't stop filling — overfilling past the normal level Water leaking or dripping from the washer after the cycle has ended No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cycle stalling at the fill step and never advancing to wash Hot water inlet blocked by calcium or mineral deposits after years of hard-water use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including: Whirlpool top-load washers and laundry centers Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Complete kit — includes mounting bracket, screws, and installation instructions Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform Approximately 5.7" tall, metal and plastic construction Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 285805 Part Type Washer Water Inlet Valve Kit Condition Genuine OEM Brand Whirlpool Application Direct-Drive Top-Load Washers / Laundry Centers Kit Contents Water inlet valve, mounting bracket, screws, instructions Ports 2 (hot and cold) Hose Compatibility 1/2" ID Thread Specification Two 3/4"-11 x 1/2" NHT hose threads Height Approx. 5.7 in. Material Metal and plastic Color Blue or green (both correct — varies by production run) Quantity 1 valve kit Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions My valve is blue but the old one was green (or vice versa). Did I get the wrong part? No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance. The new valve's bracket doesn't match my old one. What do I do? This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent. Only hot water won't fill, but cold works fine. Is that this valve? Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled. My washer won't stop filling. Is that dangerous, and is it this valve? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH03X36897 Washer Genuine OEM Mode Shifter Actuator – Compatible with GE & Hotpoint Washers Product Description Restore proper wash and spin operation with the WH03X36897 Washer Genuine OEM Mode Shifter Actuator. This factory-approved component shifts the washer between agitation and spin modes during the wash cycle. A failing mode shifter can cause the washer to agitate but not spin, spin improperly, make clicking noises, or display cycle errors. Replacing it with this Genuine OEM actuator ensures precise shifting, reliable performance, and correct cycle operation. Replaces Part Numbers WH03X36897, WH18X27186, AP7225424, PD00087767, EAP17626543, PS17626543 Compatibility This Genuine OEM mode shifter actuator fits select GE and Hotpoint top-load washers. Example compatible models include (but are not limited to):GE GTW335ASN1WW, GTW465ASN2WW, GTW485ASJ1WSHotpoint HTW240ASK6WS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and dependable operation 🔄 Accurate Mode Shifting – Properly switches between wash and spin cycles 🔇 Quiet, Smooth Operation – Reduces clicking or erratic shifting noises 💪 OEM-Grade Durability – Designed for long service life under repeated cycles 🛡️ Fixes Common Issues – Solves no-spin, improper agitation, or cycle errors 📐 Product Specification Part Number: WH03X36897 Component Type: Washer Mode Shifter Actuator Voltage: 120V AC Mounting: Direct-fit installation on transmission assembly Function: Controls agitation-to-spin shifting Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Steps: Disconnect power and tilt the washer back for bottom access. Locate the mode shifter actuator near the transmission. Disconnect the wiring harness and remove mounting screws. Install the new WH03X36897 actuator and secure it in place. Reconnect wiring, return washer upright, and restore power. Run a test cycle to confirm proper shifting. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore correct washer cycle operation — Add to Cart Now for a factory-quality repair!

Read more less

XPARTCO DC96-01703H Washer Water Pressure Switch - Compatible with Samsung Washers Product Description Ensure your Samsung washer operates flawlessly with the replacement DC96-01703H Washer Water Pressure Switch. This replacement part is designed for select Samsung washing machines, providing precise water level control to prevent overfilling, underfilling, or water leakage. It resolves issues like error codes, inconsistent water levels, or failure to start wash cycles, delivering reliable performance for your appliance. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: DC96-01703H, PD00030634, EAP8764044, AP5799898, 3997570, PS8764044. Compatibility: Compatible with models including but not limited to: Samsung: WA48J7700AW/A2, WA48H7400AW/A2, WA50F9A7DSP/A2, WA52M7750AV/A4, WA56H9000AP/A2 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung washing machines. 🔥 Specifications: Water pressure switch with electrical connectors and 28" hose attachment. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves water level issues, error codes, and improper filling. Product Specification Part Number: XPDC96-01703H Component Type: Washer water pressure switch Mounting: Secures to washer control panel with screws or clips Operating Conditions: Suitable for washer environments Installation Notes: Safety First: Disconnect the washer from power and water sources before installation. Follow the owner’s manual for guidance. Shop for high-quality replacement appliance parts with a 30-day return policy. Fix your washer today! Add to cart now for a reliable solution!

Read more less

W11244231 Genuine OEM Whirlpool Washer Drain Hose The W11244231 is a genuine Whirlpool OEM drain hose for Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers. This flexible tube carries used water from the washer tub to your house drain after every wash cycle, connecting the washer's outlet to your standpipe or utility sink drain connection. This hose is approximately 4 feet long and ships as a kit that includes a clamp. Over time, normal wear and tear, exposure to high water pressure or temperature, or physical damage from kinks and pinches can cause the hose to crack, bulge, or leak. A failing drain hose typically shows up as water leaking around the hose connections or along its length, slow or improper draining, or visible cracks and bulges in the hose material. It directly replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897. Quick Answer The W11244231 Genuine OEM Whirlpool Washer Drain Hose fixes Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers with a cracked, bulging, or leaking drain hose, slow draining, or a missing hose. Approximately 4 feet long, includes clamp. Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, PS12578897. This is a separate part from our W11281268 drain hose listing, which fits a different set of washer models — always confirm your exact model number before ordering. Common Problems This Part Fixes Water leaking around the hose connections or along its length Slow draining or improper drainage of the tub Visible cracks, bulges, or damage to the hose material Missing drain hose on a newly acquired or moved washer Reduced washer efficiency from a clogged, worn, or damaged hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain hose directly replaces the following OEM and cross-reference part numbers: W11244231, W10826733, W10221546, 4814009, W10769870, W10821090, W11199768, W11199820, W11203364, W11249137, AP6339776, AWP43752, OEM19019337, PD00045186, PS12578897 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain hose is compatible with select Whirlpool washers, and also fits select Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers built on the Whirlpool platform, spanning Whirlpool series 1CWTW4, 2DWTW, 3DWTW, 3LWTW, 3NWTW4800, 3SWTW4800, and 4GWTW, and Maytag series 3LMVWC, 4GMVW, 4KMVW, 4KNTW, 7MMVW, and MVWX6, including specific model numbers such as: MVWX655DW1, NTW4516FW3, VAW3584GW0 WTW4816FW2, WTW5000DW1, WTW5000DW2, WTW5000DW3, WTW9500EC0 WTW5100HC0, WTW5500BW0, WTW5600XW0, WTW5700AC0, WTW5800BC0, WTW6120HC0 WTW7000DW0, WTW8000DW0 ITW4871FW0, ITW4871FW1, ITW4871FW2 4KMVWC415FW0, 4KMVWC430JW0, 7MWTW1504DQ0 Kenmore 11026112310 Note — not the same as W11281268: This is a separate part from our W11281268 drain hose listing, which fits a different set of Whirlpool, Maytag, and Amana washer models with its own cross-reference set. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hose your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified length and fitting design Carries wastewater from the washer to your house drain during the drain cycle Resolves "leaking around connections," "slow draining," and "cracked or bulging hose" symptoms Approximately 4 feet long Ships as a kit including a clamp Direct drop-in replacement — matches the original fitting and length Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897 Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11244231 Part Type Washer Drain Hose Kit Condition Genuine OEM Brand Whirlpool Length Approx. 4 feet Includes Clamp Related Part W11281268 (6' hose, different model fitment, sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 drain hose kit Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Transfer Your Old Clamps To The New Hose Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off the water supply before beginning. Wear work gloves. Remove the back panel of the washer, then the lower front access panel to access the drain hose connection. Place a towel down before disconnecting any hoses to catch any remaining water. Disconnect the old hose from the washer's outlet spout and from your standpipe or drain connection. Transfer your existing hose clamps onto the new W11244231 hose during installation. Fit the new hose over the outlet spout and secure the clamp, then reconnect the other end to your house drain. Reinstall the lower front access panel and back panel. Restore the water supply and power, then run a test cycle to confirm the hose is secure with no leaks. Tools needed: multi-screwdriver, standard pliers, work gloves, towel. Frequently Asked Questions My washer is leaking. Is this the right part? It's worth checking, especially if the leak appears to come from around the hose connections or along its length rather than from the washer's tub or valve area. A cracked, bulging, or worn drain hose is a documented cause of leaking and can be resolved by replacing the hose to restore proper drainage. Is this the same as your W11281268 listing? No, these are two separate genuine Whirlpool drain hoses that fit different sets of washer models, with their own distinct cross-reference lists. Always confirm your exact model number against the compatibility list for each listing rather than assuming either hose is a universal fit. Do I need to buy new hose clamps separately? This hose kit includes a clamp, but you'll still need to transfer your existing clamps from the old hose for any connections that don't come with a new one included. Keep your old hardware on hand during the swap rather than discarding it with the old hose. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length and fitting configuration of the drain hose originally installed on your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH10X29537 Front Load Washer Door Fits specific GE Washer models. Description: This Washer Door is a Genuine OEM replacement part for GE washing machines. It is the main access point to the washer drum, allowing you to load and unload your laundry with a secure and tight seal during operation. 

Read more less