Search results for "Dryer Motors"

XPARTCO 3392519 Dryer Thermal Fuse Replaces WP3392519 The XPARTCO 3392519 is an aftermarket replacement dryer thermal fuse compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. The thermal fuse is a critical one-time-use safety device mounted on the exhaust duct or blower wheel housing that monitors the dryer's operating temperature. When the dryer overheats — typically due to a clogged exhaust vent or restricted airflow — the thermal fuse permanently opens the circuit and cuts power to the heating system to prevent a fire. Once blown, the thermal fuse cannot be reset and must be replaced. This part measures 2 inches long x 1/2 inch wide, features two 3/16-inch terminals, and opens at approximately 196°F (91°C). Important: always check and clear the exhaust vent when replacing this fuse, as restricted airflow is the most common cause of thermal fuse failure. Quick Answer The XPARTCO 3392519 Dryer Thermal Fuse fixes dryers that won't start, won't heat, or stop mid-cycle due to overheating. It is a one-time-use safety fuse that permanently opens at 196°F (91°C) to cut power and prevent fires. Compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef dryers. Replaces WP3392519 and many other part numbers. Common Problems This Part Fixes Dryer won't start at all Dryer runs but produces no heat Dryer stops mid-cycle and won't restart Timer advances but drum does not heat Dryer shuts off too soon before clothes are dry No continuity detected across fuse terminals during testing Replaces Part Numbers This thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (including Duet and Cabrio series) Kenmore / Sears dryers (including Elite series) KitchenAid dryers Maytag dryers (including Centennial and Neptune series) Roper dryers Estate dryers Inglis dryers Crosley dryers Amana dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-time-use safety device — permanently opens at 196°F (91°C) to cut power and prevent dryer fires Mounts on the exhaust duct or blower wheel housing — easy access for DIY replacement Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Broad compatibility across 11 major appliance brands DIY-friendly repair — installs with basic hand tools in under 30 minutes Budget-friendly safety fix — one of the most common and least expensive dryer repairs Product Specifications Part Number 3392519 Part Type Dryer Thermal Fuse Condition Aftermarket Replacement Application Gas and Electric Dryers Opening Temperature 196°F (91°C) Length 2 inches Width 1/2 inch Terminal Size 3/16 inch (2 terminals) Resettable No — one-time use only, must be replaced when blown Location on Dryer Exhaust duct / blower wheel housing Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef Installation Notes ⚠️ Safety First — Unplug Dryer and Shut Off Gas Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. The thermal fuse is located on the exhaust duct or blower wheel housing — access it by removing the back or front panel depending on your dryer model. Disconnect the two wire terminals from the old fuse, remove the fuse from its bracket, install the new fuse in the same position, reconnect the terminals, and reassemble the panel. Tools needed: Phillips screwdriver, 1/4-inch nut driver, and a multimeter to confirm the new fuse has continuity. ⚠️ Important: Before completing the repair, always check and clear the exhaust vent of any lint buildup — a blocked vent is the most common cause of thermal fuse failure and will blow the new fuse if not corrected. Frequently Asked Questions Will the 3392519 fit my dryer? This thermal fuse is compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. Use the model search above to verify your model, or contact our support team before ordering. What does a dryer thermal fuse do? The thermal fuse is a one-time-use safety device that monitors the temperature inside the dryer. When the dryer overheats — typically due to a clogged exhaust vent — the fuse permanently opens the circuit, cutting power to the heating system to prevent a fire. Once blown, it cannot be reset and must be replaced. How do I know if my thermal fuse is blown? Test the fuse with a multimeter set to continuity mode. Touch the probes to each of the two terminals. A working fuse will show continuity (beep or near-zero ohms). A blown fuse will show no continuity (open circuit). If there is no continuity, the fuse is blown and must be replaced. Why did my thermal fuse blow? The most common cause is restricted airflow due to a clogged or kinked exhaust vent, a plugged lint trap, or a damaged blower wheel. Always check and clear the exhaust vent before or after replacing the fuse — failing to do so will cause the new fuse to blow again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable overheat protection at a more affordable price point. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

12638200000241 Genuine OEM Midea Dryer Drum Belt The 12638200000241 is a Genuine OEM Midea replacement dryer drum belt compatible with a wide range of Midea, Criterion, and Insignia electric and gas dryers, including the MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, and MDD160 series. The drum belt wraps around the dryer drum and the motor pulley, transferring the motor's rotation to spin the drum during the drying cycle. When the belt breaks, stretches, or wears out, the motor continues to run but the drum no longer spins — clothes sit still in the drum while the motor hums, and the dryer cannot complete a normal cycle. As a Genuine OEM part manufactured by Midea to factory specifications, the 12638200000241 is constructed from durable black rubber. Packaged dimensions are approximately 11" L x 3" W x 2" H. Note: if the drum belt has failed, this is also a good opportunity to inspect the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley assembly while the dryer cabinet is open — these components wear together and a failing roller or pulley can accelerate belt wear. Installs in 45–60 minutes with basic hand tools. Quick Answer The 12638200000241 Genuine OEM Midea Dryer Drum Belt fixes Midea, Criterion, and Insignia dryers where the motor runs but the drum doesn't spin, the belt has snapped or is visibly stretched, or where there's a burning rubber smell during operation. Black rubber drum belt. Packaged dimensions approximately 11" L x 3" W x 2" H. Genuine OEM. Compatible with Midea MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, MDD160 series, plus Criterion CDE41N1AW/CDG41N1AW/CDG45N1AW and Insignia Midea-built models. Common Problems This Part Fixes Drum not spinning — belt has broken or slipped off Motor runs and hums but the drum stays still Drum spins intermittently — belt slipping under load Burning rubber smell during operation — belt slipping on the motor pulley Squealing or chirping noise during the drying cycle — belt frayed or stretched Belt visibly cracked, frayed, broken, or missing inside the dryer cabinet Extended drying times — drum not rotating at correct speed due to a worn belt Replaces Part Numbers This drum belt directly replaces the following part number: 12638200000241, AP7158561, PS18170626 This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drum belt is compatible with select Midea, Criterion, and Insignia electric and gas dryers, including: Midea electric dryers — MLE41N1AWW, MLE45N1AWW, MLE45N1BWW, MLE45N3BMG, MLE45N3BWW, MLE47A3AGG, MLE47C3AWW, MLE47C4AWW, MLE47R5BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — MLTE37N1BWW, CLADE67W, MDD160A2301E1305 and related models Criterion — CDE41N1AW (electric), CDG41N1AW (gas), CDG45N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Wraps around the dryer drum and motor pulley to transfer the motor's rotation to spin the drum Durable black rubber construction designed for continuous flex and motor load Packaged dimensions: approximately 11" L x 3" W x 2" H Compatible with the full Midea, Criterion, and Insignia electric and gas dryer platform Often replaced along with the drum support rollers (Midea 12638000004021) and idler pulley assembly Installs in 45–60 minutes with basic hand tools Product Specifications Part Number 12638200000241 Part Type Dryer Drum Belt Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Material Rubber Color Black Packaged Dimensions Approximately 11" L x 3" W x 2" H Often Replaced With Drum Support Roller (Midea 12638000004021) Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum, drive belt, and motor/idler pulley assembly. Take a photo of the existing belt routing before removing anything — this is essential for correct reassembly. Release the old belt from the idler pulley and slide it off the drum and motor pulley. Carefully lift the drum out and inspect the drum support rollers and idler pulley for wear — replace them now if needed while the dryer is open. Wrap the new 12638200000241 belt around the drum (ribbed side against the drum). Reinstall the drum, then route the belt around the motor pulley and under the idler pulley, allowing the idler to tension the belt. Reassemble the front panel and top panel in reverse order. Restore power (and gas, for gas models) and run a test cycle to confirm smooth, quiet drum rotation. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions How do I know if the drum belt has failed? The clearest sign of a broken drum belt is a dryer where the motor starts and runs normally, but the drum does not spin — you'll hear the motor humming with no drum movement. If you open the door mid-cycle and the drum spins freely with no resistance (as if disconnected from the motor), the belt has either broken or slipped off completely. A stretched or worn belt that still drives the drum may also produce squealing or burning rubber smells from slippage on the motor pulley. Visually inspecting the belt after removing the dryer's front panel confirms the condition. Should I replace the drum rollers and idler pulley at the same time? Yes — since the dryer cabinet must already be opened and the drum removed to replace the belt, this is the ideal time to also inspect and replace the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley. All three components form the drum drive system and tend to wear together. A worn roller or pulley is often what caused the belt to fail prematurely in the first place. Addressing them together in a single repair eliminates the most common drum drive failure points and prevents a near-term repeat teardown. Does this belt fit Insignia and Criterion dryers as well as Midea? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size class are manufactured by Midea and use the same internal components, including this drum belt. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), plus Criterion CDE41N1AW (electric) and CDG41N1AW/CDG45N1AW (gas). Always verify your specific model number before ordering. Which way does the belt go around the drum — ribbed side in or out? On the drum belt, the ribbed (grooved) side should face inward, against the drum surface, while the smooth side faces outward. The ribs grip the smooth drum surface to drive it as the motor pulley turns. On the motor pulley side, the belt seats in the grooves of the small motor pulley. Take a photo of how the original belt was routed before removing it — this is the most reliable way to confirm correct orientation during reinstallation. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same drum belt installed in compatible Midea, Criterion, and Insignia electric and gas dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO AGM30045804 Dryer Thermostat Kit The XPARTCO AGM30045804 is an aftermarket replacement high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does. Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335. As an aftermarket replacement, the AGM30045804 kit is built to OEM-equivalent quality standards. Quick Answer The XPARTCO AGM30045804 Dryer Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step. What's In The Kit Component Function High-Limit Thermostat Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools. Thermistor (with wire harness) Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle. Common Problems This Kit Fixes Dryer overheating, sometimes scorching or damaging clothing Dryer running with little or no heat Inconsistent drying times — cycle shuts off too early or runs longer than necessary Temperature-related error code displayed on the control panel Clothes remaining damp after a full drying cycle High-limit thermostat that keeps tripping repeatedly Dryer that has already had its high-limit thermostat replaced once but the problem returned Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers: AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335, AGM75510744, EAP16746326, PD00083166, ALG53211, AP7195784, PS16746326. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform. Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order. Key Features Aftermarket replacement built to match LG's factory-specified resistance values and switch thresholds Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms Thermistor ships with its wire harness included High-limit thermostat resets automatically after tripping — no replacement needed after each trip Direct drop-in replacement for both original components Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335 Compatible with LG and select Kenmore and GE-branded LG-built dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number AGM30045804 Part Type Dryer High-Limit Thermostat and Thermistor Kit OEM Part Number AGM30045804 Condition Aftermarket Replacement Brand LG Kit Contents High-limit thermostat + thermistor with wire harness Thermistor Location Blower housing High-Limit Thermostat Type Automatically resetting Repair Difficulty Easy to Moderate — 30 to 60 minutes Compatible Brands LG, select Kenmore, GE (LG-built models) Installation Notes ⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead? This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit. What's the difference between the thermistor and the high-limit thermostat? The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating. My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing? Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the resistance values, switch threshold, and wire harness configuration of the original AGM30045804 high-limit thermostat and thermistor kit used in compatible LG, Kenmore, and GE-branded LG-built dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10205415 Dryer Drum Belt Replaces WPW10205415 The XPARTCO W10205415 Dryer Drum Belt is a high-quality aftermarket replacement designed to restore proper drum rotation in compatible dryers. The belt wraps around the dryer drum, connects with the motor pulley and idler pulley, and allows the drum to tumble clothes during the drying cycle. Manufactured with durable reinforced rubber, this 5-rib, 4-groove belt is built to withstand heat, tension, and everyday dryer use. It measures approximately 92 inches long and 3/8 inch wide, making it a direct replacement for W10205415 and WPW10205415. Quick Answer The XPARTCO W10205415 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or the dryer runs but does not dry properly. It fits select Whirlpool, Maytag, Amana, Samsung, Kenmore, KitchenAid, Inglis, Crosley, and Caloric dryers. Common Problems This Part Fixes Dryer drum not spinning while the motor runs Clothes not tumbling during the drying cycle Dryer runs but clothes remain wet Squealing, thumping, or slapping noise during operation Broken, loose, stretched, or worn dryer belt Visible belt pieces inside the dryer cabinet Replaces Part Numbers This dryer drum belt replaces the following OEM and cross-reference part numbers: W10205415, WPW10205415, 35001137, 6602-001314, 1937372, AWP49503, PD00003618, AP5178009, PS3494357. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers Maytag dryers Amana dryers Samsung dryers Kenmore / Sears dryers KitchenAid dryers Inglis dryers Crosley dryers Caloric dryers ⚠️ This compatibility list includes many supported models but may not be complete. Always verify your appliance model number before ordering. If you're unsure, our support team is ready to help confirm fitment. Model Cross Reference Use the Model Cross Reference section on this product page to search your appliance model number and confirm fitment. Exact model matches will show a ✓ Guaranteed Fit badge. When Should You Replace This Belt? Drum stops spinning but motor still runs You hear a snapping sound during operation Belt appears cracked, frayed, or stretched Dryer suddenly stops tumbling mid-cycle Clothes come out wet due to lack of tumbling Key Features Restores proper dryer drum rotation and tumbling 92 inch length x 3/8 inch width 5-rib, 4-groove design for secure grip Durable reinforced rubber construction Direct replacement for W10205415 and WPW10205415 Compatible with select gas and electric dryers Aftermarket replacement built to OEM-equivalent standards Product Specifications Part Number W10205415 Replaces WPW10205415 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92 inches Width 3/8 inch Ribs 5 ribs, 4 grooves Material Reinforced rubber Color Black Compatible Brands Whirlpool, Maytag, Amana, Samsung, Kenmore, KitchenAid, Inglis, Crosley, Caloric Installation Notes ⚠️ Safety First — Disconnect Power Before Servicing Unplug the dryer from the power source before starting the repair. For gas dryers, shut off the gas supply. Remove the top and front panels to access the drum. Remove the old belt and install the new W10205415 belt around the drum with the ribbed side facing inward. Route the belt around the idler pulley and motor pulley, then reassemble the dryer and run a test cycle. Frequently Asked Questions Is W10205415 the same as WPW10205415? Yes. WPW10205415 is the updated OEM part number that replaces W10205415. This aftermarket belt is compatible with both part numbers. How do I know if my dryer belt is broken? A common sign is that the dryer motor runs, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is loose, frayed, or partially broken. Will this belt fit my Kenmore dryer? Many Kenmore dryers are manufactured by Whirlpool and may use this belt. Use the Model Cross Reference search section to verify your exact model before ordering. Is this an OEM part? This is a high-quality aftermarket replacement part built to match OEM-equivalent dimensions and performance standards. It is not a genuine Whirlpool OEM part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WH11X39237 Washer Drain Pump The XPARTCO WH11X39237 is an aftermarket replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH11X39237 Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Aftermarket replacement built to OEM-equivalent quality standards Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Aftermarket Replacement Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical specifications and physical dimensions of the original WH11X39237 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

137292700 Genuine OEM Dryer Drum Belt Product Title 137292700 Dryer Genuine OEM Drum Belt - Compatible with Frigidaire, Electrolux, Kenmore Dryers Product Description Keep your dryer running smoothly with the Genuine OEM 137292700 Dryer Drum Belt from Parts-O-Matic. This Genuine OEM belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum to ensure efficient tumbling and drying. Compatible with select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryers, this belt fixes issues like failure to tumble, unusual noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryer models. 🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying. 💰 Cost-Effective Alternative: Genuine OEM part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair. 🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production. Compatibility: Compatible with models including but not limited to: Frigidaire: FEX831FS2, FEQ332ES0, FER231AS2, AGQ6000ES2 Electrolux: EIMED55IIW0, EIMED60JIW0 Kenmore: 417.91702001, 417.97812700, 417.97812702 Replaces part numbers: 137292700, 134163500, 134503900, 5303283287, AH3408299, EA3408299, AP4565702, PS3408299. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension. Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Caution: Avoid stretching the belt during installation, as this can reduce its lifespan. Shop Parts-O-Matic for Genuine OEM appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

WE11X203 Dryer Genuine OEM Heater Restring Coil Kit  Dryer heating element restring kit. This kit replaces the existing heating coil in your dryer.  This Heater restring Coil Replaces WE11X103 Heater Restring Coil.  The diameter of the coil is 1/2" OD it stretches around the pan over the ceramic insulators.   Replaces Part Numbers:WE11X203, AH265619, AP2620176, DE333, EA265619, K35-408, PS265619, WE11X0203, WE11X103C   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

4 Pack - XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 - Pack Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 6931EL3002M Dryer Blower Thermostat – Compatible with LG and Kenmore Dryers Product Description Restore proper temperature regulation in your dryer with the XPARTCO 6931EL3002M Dryer Blower Thermostat. This Dryer Blower Thermostat is a replacement part for select LG dryer models. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle. Common causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.  Replaces Part Numbers 6931EL3002M, 6931EL3002A, 6931EL3002K, PD00023476, EAP8747887, AP5782317, PS8747887. Compatibility This replacement blower thermostat (mounts on blower housing). fits select LG and Kenmore (manufactured by LG) dryers. Example compatible models include (but are not limited to):LG DLE5977W, DLE3170W, DLEX3470V, and Kenmore 796.81022900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature control performance 🌡️ Accurate Temperature Regulation – Maintains proper blower housing heat levels. Thermostat 85C, 185F. 💰 Budget-Friendly Option – Provides OEM-level reliability at a lower price 🛠️ Easy Installation – Direct-fit design with standard mounting hardware 🛡️ Fixes Common Issues – Solves overheating, no-heat problems, long dry times, and auto-shutoff issues 📐 Product Specification Part Number: 6931EL3002M Component Type: Dryer Blower Thermostat Material: Metal thermostat housing with bimetal sensor Temperature Rating: Opens/closes at OEM-equivalent temperature thresholds Mounting: Two-screw mounting to blower housing Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before performing repairs to prevent electrical shock and injury. Steps: Disconnect power and remove the dryer’s rear access panel. Locate the blower housing and identify the thermostat. Remove the mounting screws and disconnect the wiring. Install the new XPARTCO 6931EL3002M thermostat in the same position. Reconnect wires, reinstall the panel, and restore power. Run a test cycle to confirm proper temperature cycling. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore safe temperature control — Add to Cart Now for a reliable, cost-effective repair!

Read more less

ERP W10909685 Dryer Thermal Fuse Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won't start or will run but not heat. The thermal fuse cannot be reset. Fuses often blow due to a clogged dryer vent. Replaces part Numbers: W10909685, W10693363, G4AP0506, F 091C ACA2, PD00036363, EAP11766766, AP6034383, PS11766766.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine Whirlpool WP37001042 Dryer Drum Roller - Compatible with Admiral, Amana, Magic Chef, Maytag, Speed Queen Product Description Restore smooth and quiet operation to your dryer with the Genuine Whirlpool WP37001042 Dryer Drum Roller. This OEM drum roller is designed for select Admiral, Amana, Magic Chef, Maytag, and Speed Queen dryers, supporting the drum for even tumbling and efficient drying. Made of durable rubber, metal, and plastic, it ensures long-lasting performance, addressing issues like loud rumbling, squeaking, or uneven drum movement. Note: Includes one drum roller. Disconnect power and gas (if applicable) before installation. For even wear, replace all rollers at the same time. Replaces part numbers: WP37001042, 37001042, 14218934, 500214, 500214P, WP37001042VP, 5-0214, 500214P-REPL, 500214-REPL,37001042-REPL, 500214P, 500214, PD00002495, EAP11741913, AP6008773, PS11741913. Compatibility: Compatible with models including but not limited to: Admiral: ADE7005AKW, ADE7005AYW, ADE9005AGW, ADG7005AWW Amana: AEM197, AEM377, AEM397, AEM407L, AEM407W, ALE120RAW, ALE230RAW Maytag: MDE3706AGW, MDG2706AGW Speed Queen: AGM199, AGM379, AGM399 Bosch, Crosley, Danby, Kenmore, Magic Chef: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Admiral, Amana, Magic Chef, Maytag, and Speed Queen dryers. 🔄 Specifications: OEM drum roller made of rubber, metal, and plastic for smooth drum rotation. 💪 Reliable Performance: Authentic Whirlpool part ensures superior durability and performance. 🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves loud rumbling, squeaking, or uneven drum movement. Product Specification Part Number: Genuine Whirlpool WP37001042 Component Type: Dryer drum roller Material: Rubber, metal, plastic Mounting: Bolt-mounted to dryer drum assembly Operating Conditions: Suitable for household and commercial dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

WPW10420741 Genuine OEM Dryer Push To Start Switch - Compatible with Whirlpool, Kenmore, Maytag Product Description Restore your dryer’s functionality with the WPW10420741 Genuine OEM Dryer Push To Start Switch. This Whirlpool-manufactured switch, featuring screw terminals, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It initiates the drying cycle with a simple button press, addressing issues like the dryer not starting or starting inconsistently. Built for durability, it ensures reliable performance under frequent use. Note: Includes (1) push to start switch. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WPW10420741, W10420741, PD00008413, EAP3632880, AP6021228, PS11754549. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WET4027HW0, WET4027HW1, WET4027HW2, YWET4027HW0, 7MWGT4027HW0 Kenmore: 110.97591420, 110.97591220, 110.97592420 Maytag: YNED4655EW, YIED4671EW Roper: RED4516FW0, RED4640YQ0, RED4640YQ1, RED4645EW0 Crosley: VDEW6511RW0, VED6505GW0 Amana: NED4655EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana, and other dryers. 🔧 Specifications: Genuine OEM Whirlpool push to start switch with screw terminals, 120V, 2-terminal configuration. 💪 Reliable Performance: Initiates drying cycle with a button press, ensuring consistent operation. 🛠️ Easy Installation: Requires a screwdriver; typically installed in 10–20 minutes. 🛡️ Effective Fixes: Resolves dryer not starting or inconsistent starting issues. Product Specification Part Number: WPW10420741 Component Type: Dryer push to start switch Material: Plastic and brass/stainless steel Electrical Specs: 120V, 2-terminal, normally open, single-pole single-throw (SPST) Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less