Genuine OEM WE4M137 Dryer High Limit Thermostat
The WE4M137 is a genuine OEM high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip.
This is a genuine OEM part manufactured to the original factory temperature rating and mounting — not an aftermarket equivalent — so trip point and reset behavior match what came on the dryer originally. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause.
Quick Answer
The Genuine OEM WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Genuine OEM, factory temperature rating, auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool.
Common Problems This Part Fixes
Dryer shuts off a few minutes into a heat-dry cycle
Dryer stops early and won't restart until it cools down
Intermittent shutdowns during the drying cycle
Clothes coming out damp because the cycle keeps cutting short
Dryer won't start at all if the thermostat has failed in an open position
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This thermostat directly replaces the following part numbers:
WE4M137 replaces WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900
These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct genuine replacement for this component regardless of which number appears on your dryer's parts diagram.
Compatibility
This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including:
Kenmore 2661532110, GE 2661532210
Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models DBXR463ED1WW, DBXR463ED2WW, DBXR463EG7WW, DHDVH52EF0WW, DHDVH66EH0BB, DPSR610EG0WT, DPSR610EG1WT, DPSR610EG2WT, DPSR610EG3WT, DPSR610EG4WT, DPSR610EG5WT, DPSR610EG6WT, DPSR610EG7WT, DPSR610EG8WT, GFDN245EL1MS, GFDS350GL0WW, GFDS350GL1WW, GFDS355EL0MV, GLDP280ED0WS, GLDP280GD0WS, GTDN500EM0WS, GTDN500EM1WS, GTDN500EM2WS, GTDX180ED0WW, GTDX180ED1WW, GTDX180ED3WW, GTDX180ED4WW, GTDX180ED5WW, GTDX180ED6WW, GTDP180ED0WW, GTDP180ED1WW, GTDP200EF1WS, GTDP220EF1WW, GTDP301EL1WS, GTDP490ED0WS, HTDP120ED0WW, HTDX100ED0WW, NBXR333EG1WW, NWXR483EG8WW
Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM high limit thermostat — factory fit and trip-point accuracy, not an aftermarket equivalent
Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse
Rated to open at approximately 315°F to prevent overheating damage
Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms
Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models
Straightforward swap — typically 15–30 minutes with basic hand tools
Product Specifications
Part Number
WE4M137
OEM Part Number
WE4M137
Part Type
Dryer High Limit Thermostat (Auto-Reset)
Condition
Genuine OEM
Temperature Rating
L315-65F (Opens ~315°F, Auto-Resets on Cooling)
Location
Upper Right Side of Heater Housing
Application
GE, Hotpoint & Kenmore Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure.
Frequently Asked Questions
My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need?
Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause.
Is this a one-time fuse like the thermal fuse, or does it reset itself?
This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed.
Why does my dryer keep tripping this thermostat?
Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again.
Is this a genuine GE part or an aftermarket copy?
This is a genuine OEM thermostat manufactured to the original factory specification — not an aftermarket equivalent — so trip temperature and reset behavior match what came on the dryer originally.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH13X10014 Washer Water Inlet Valve
The XPARTCO WH13X10014 is an aftermarket replacement water inlet valve for GE washer/dryer combination units — a single cabinet that houses both wash and dry functions and shares one door, lid, and control system for both. This valve sits at the point where the hot and cold water supply lines connect, and it's the gatekeeper for every drop of water that enters the tub during the wash portion of a cycle. When the control calls for a fill, the valve's solenoid opens to admit water; once the correct level is reached, it closes again.
Common causes of failure include mineral or sediment buildup inside the valve body that prevents it from sealing fully, and a burned-out internal solenoid coil. A failing valve on a combo unit produces the same core symptoms you'd see on a standalone washer: the wash side won't fill, fills too slowly, won't stop filling, or leaks after the cycle ends — but because a combo unit shares more components in a single cabinet than separate machines do, it's worth confirming the water issue is isolated to the valve and not connected to other combo-specific parts nearby, such as our WH12X955 lid switch listing, which serves this same GE combo platform. It directly replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040.
Quick Answer
The XPARTCO WH13X10014 Washer Water Inlet Valve fixes GE washer/dryer combo units that won't fill with water, fill slowly, won't stop filling, or leak after the cycle ends. For GE's combination washer/dryer platform (WSM2420/WSM2480 series). Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, 944040. This valve is specific to GE's washer/dryer combo unit — not a standalone front-load or top-load washer valve.
Common Problems This Part Fixes
Washer/dryer combo won't fill with water at the start of the wash cycle
Water fills much more slowly than normal
Unit won't stop filling — water continues past the normal level
Water leaking or dripping after the cycle has ended
Cycle stalling at the fill step and never advancing to wash
No hot water reaching the tub, or no cold water reaching the tub
Unit not washing properly due to insufficient or incorrect-temperature water
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
WH13X10014, WH13X0084, WH13X10013, WH13X84, AP3203931, 944040, AH756629, EA756629, AGE844170, PD00066092, PS756629
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select GE washer/dryer combination units, including model numbers such as:
GE WSM2420D0WW, WSM2420D1WW, WSM2420D2WW, WSM2420D3WW, WSM2420D4WW, WSM2420D5WW
GE WSM2420D0CC, WSM2420D1CC, WSM2420D2CC
GE WSM2420TAAWW, WSM2420TBAWW, WSM2420TCAWW, WSM2420TAAAA, WSM2420TAACC, WSM2420TBAAA
GE WSM2420SAZAA, WSM2420SBZAA, WSM2420SBZWW, WSM2420SCZAA, WSM2420SCZWW, WSM2420SDZWW
GE WSM2480D0WW, WSM2480D1WW, WSM2480D2WW, WSM2480D3WW
GE WSM2480SAZAA, WSM2480SAZWW, WSM2480SBZAA, WSM2480SBZWW, WSM2480SEZAA, WSM2480TCAWW
Note: This valve is built specifically for GE's washer/dryer combination units. It is not the same valve used on GE's standalone front-load washers (such as our WH13X10029 listing) and is not interchangeable with them. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement water inlet valve for GE washer/dryer combination units
Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure
Solenoid-actuated design opens and closes precisely on the control's signal
Direct drop-in replacement — matches the original mounting and hose connections
Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040
Compatible with GE washer/dryer combo units, including WSM2420 and WSM2480 series
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair using basic hand tools
Product Specifications
Part Number
WH13X10014
OEM Part Number
WH13X10014
Part Type
Washer Water Inlet Valve
Condition
Aftermarket Replacement
Application
GE Washer/Dryer Combination Units
Actuation
Solenoid-operated
Connections
Hot and cold water supply inlets
Quantity
1 valve
Compatible Brand
GE
Installation Notes
⚠️ Shut Off Water Supply And Unplug Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. On these combination units, the top of the cabinet often lifts off or opens as a single enclosure covering both the wash and dry sections, which also carries the lid switch wiring — note this connector's location before pulling the panel free. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove its mounting screws, and pull it free. Install the new WH13X10014 in the same position, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold water supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet enclosure, reconnecting the lid switch harness if it was disturbed, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the wash side fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves.
Frequently Asked Questions
Is this the same valve used on a standalone GE washer?
No. This valve is built specifically for GE's washer/dryer combination units, which share a single cabinet and control system for both wash and dry functions. GE's standalone front-load washers use a different valve (such as our WH13X10029 listing), and the two are not interchangeable. Always confirm whether your appliance is a combo unit or a standalone washer before ordering.
My unit won't stop filling. Is that this valve?
Yes, this is one of the most common symptoms of a failing valve. A worn internal seal can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it.
Only hot or only cold water isn't coming in. Do I need the whole valve?
Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold or serviced as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, connection type, and mounting configuration of the original WH13X10014 valve used in compatible GE washer/dryer combination units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH11X39237 Genuine OEM GE Washer Drain Pump
The WH11X39237 is a Genuine OEM GE replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle.
This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The WH11X39237 Genuine OEM GE Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the drum after a cycle
Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes)
Loud humming, grinding, or buzzing noise during the drain cycle
Washer stopping mid-cycle due to a drain fault
Water leaking from around the drain pump area
Drain pump running continuously but water not being expelled
Pump impeller jammed by debris and motor burned out
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790.
WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part.
Compatibility
This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines:
GE front-load washers — GFW510 series
GE front-load washers — GFW550 series
GE front-load washers — GFW650 series
GE front-load washers — GFW655 series
GE front-load washers — GFW850 series
GE Profile front-load washers — PFW870, PFW950, PFW955 series
GE Profile front-load washers — PFQ83 series
GE 2-in-1 Washer/Dryer Combo (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included
Removes water from the drum during drain and spin cycles for proper washer operation
Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs
Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models
WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539
Direct replacement — installs into existing pump housing with no modification required
Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series
DIY-friendly repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
WH11X39237
Supersedes
WH11X29539 (discontinued)
Part Type
Washer Drain Pump and Filter Assembly
Condition
Genuine OEM
Application
GE Front-Load Washers and 2-in-1 Washer/Dryer Combos
Voltage
120V AC
Frequency
60 Hz
Amperage
1.2A
Includes
Pump motor, impeller housing, and integrated filter
Compatible Series
GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83
Compatible Brands
GE, GE Profile
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels.
Frequently Asked Questions
What is the difference between WH11X39237 and WH11X29539?
These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order.
Should I check the pump filter before replacing the drain pump?
Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step.
How do I know if my drain pump has failed?
A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out.
Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models?
Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump and filter assembly installed in compatible GE and GE Profile front-load washers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
3405-001117 Genuine OEM Refrigerator Dispenser Control Switch - Compatible with Samsung
Product Description
Restore your refrigerator’s dispenser functionality with the 3405-001117 Genuine OEM Refrigerator Dispenser Control Switch. This Samsung-manufactured microswitch is designed for select Samsung refrigerators, controlling the activation of the water and ice dispenser mechanism. It ensures reliable dispensing, addressing issues like unresponsive or intermittent water/ice dispensing for a seamless user experience.
Note: Includes (1) dispenser control microswitch. Disconnect power before installation. Verify compatibility with your refrigerator model.
Replaces part numbers: 3405-001117, DA34-00011A, 110634, 3727507, PD00033242, EAP11712663, AP5962465, PS11712663.
Compatibility:
Compatible with select Samsung refrigerator models, including but not limited to:
Samsung: RS2530BBP, RS2530BSH, RS2530BWP, RS2555BB, RS2555SL, RS2555SW, RS2577BB, RS2577SL, RS2577SW, RS2630SH, RS2630WW, RS265LABP, RS265LAWP, RS277ACBP, RS277ACPN, RS277ACWP
Common models: Samsung RS253BABB, RS253BAVQ, RS255BABB, RS255BASB, RS257BARB
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung refrigerators with water and ice dispensers.
🔧 Specifications: Genuine OEM Samsung microswitch, single-pole, double-throw (SPDT), 0.1A, 125/250V.
💪 Reliable Performance: Ensures precise activation of the water and ice dispenser mechanism.
🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–20 minutes.
🛡️ Effective Fixes: Resolves unresponsive or intermittent water/ice dispensing issues.
Product Specification
Part Number: 3405-001117
Component Type: Refrigerator dispenser control switch
Material: Durable plastic housing with metal contacts
Operating Conditions: 0.1A, 125/250V, suitable for refrigerator dispenser environments
Compliance: UL-listed, Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the refrigerator from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator’s dispenser working smoothly today!
Add to cart now for a reliable fix!
XPARTCO 131763310 Washer Door Striker
The XPARTCO 131763310 is an aftermarket replacement door striker (also called a door strike or door catch) compatible with select Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan front-load washers. The door striker is a small plastic tab mounted on the washer door that engages with the door lock assembly on the front of the washer when the door is closed — activating the door switch and allowing the washer to start, fill, and spin. When the striker breaks or wears down, the door will not properly activate the door lock, causing the washer not to start, not to fill, or to display a door-related error code.
Made from durable white plastic, this striker measures approximately 1-1/4" L x 9/16" W x 2-9/16" H with approximately 2 inches between mounting holes (center to center). It directly replaces 131763300, 134456600, 1032664, LP3310, AP3580441, and several additional cross-reference numbers. Sold individually. Installs in under 15 minutes with a Phillips screwdriver.
Quick Answer
The XPARTCO 131763310 Washer Door Striker fixes Frigidaire-platform front-load washers where the door won't activate the door lock, the washer won't start, won't fill, leaks from the door, or shows a door-related error code. White plastic, approx. 1-1/4" L x 9/16" W x 2-9/16" H, ~2" between mounting holes. Sold individually. Phillips screwdriver only — installs in under 15 minutes. Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, and more.
Common Problems This Part Fixes
Washer door will not properly latch or activate the door lock when closed
Washer will not start — door switch not being triggered by the striker
Washer will not fill with water — door lock not engaged
Washer will not spin — door lock fault preventing cycle completion
Water leaking from the door area due to door not sealing properly
Door-related error codes displayed on compatible models
Broken, cracked, or missing door striker visible on the washer door
Replaces Part Numbers
This door striker directly replaces the following OEM and cross-reference part numbers:
131763310, 134456600, 131763302, 1032664, 131763300, AH890617, EA890617, AP3580441, PS890617, AFR14210, PD00000391, EAP2378364, AP4508273, PS2378364, WH10X10004, 824421, AH269392, EA269392, AP2621447, PS269392.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door striker is compatible with select front-load washers from the following brands:
Frigidaire front-load washers (ATF, ATFB, BLTF, GLTF, LTF, FTF, FAFW, FRFW series and more)
Kenmore / Sears front-load washers (select Frigidaire-built models)
Electrolux front-load washers (select models)
Crosley front-load washers (CFW, CLCE series)
Gibson front-load washers (GTF series)
White-Westinghouse front-load washers
Kelvinator front-load washers
Tappan front-load washers
Note: The 131763310 (white) and 131763302 (gray) are interchangeable and functionally identical — the only difference is color. Either part will work as a replacement regardless of which color was originally installed.
Key Features
Engages with the door lock assembly to activate the door switch, allowing the washer to start, fill, and run
Critical safety component — washer will not operate without a properly functioning door striker
Durable white plastic construction — strong and wear-resistant for long service life
Dimensions: approx. 1-1/4" L x 9/16" W x 2-9/16" H; ~2" between mounting holes (center to center)
Sold individually — one striker per order
Direct replacement for 131763300, 134456600, 1032664, and LP3310
Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan washers
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver only
Product Specifications
Part Number
131763310
Part Type
Washer Door Striker (Door Strike / Door Catch)
Condition
Aftermarket Replacement
Application
Front-Load Washers
Dimensions
Approx. 1-1/4" L x 9/16" W x 2-9/16" H
Mounting Hole Spacing
Approx. 2" center to center
Color
White
Material
Plastic
Sold As
Single striker
Compatible Brands
Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, Tappan
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. Open the washer door and locate the door striker — it is the small plastic tab mounted on the inside of the door, typically near the top or center of the door panel. Remove the two Phillips screws securing the old striker to the door. If the striker is broken, the screws may already be loose or missing. Align the new 131763310 striker with the mounting holes in the door and secure it with the two Phillips screws. Close the door to confirm it clicks firmly into the door lock assembly. Restore power and run a short cycle to verify the washer starts, fills, and runs normally. Tools needed: Phillips screwdriver only.
Frequently Asked Questions
What does the washer door striker do?
The door striker is the small plastic tab on the washer door that engages with the door lock assembly mounted on the front of the washer when the door is closed. As the door closes, the striker pushes into the door lock, activating the door switch — a signal to the control board that the door is securely closed. The washer will not start, fill, or spin unless the door switch is activated by the striker. A broken or worn striker means the door lock is never properly engaged, so the washer appears to be in a constant "door open" state even when the door is physically shut.
What is the difference between the 131763310 and 131763302 door strikers?
Both are Frigidaire-platform door strikers, they are different color and interchangeable. The 131763310 is used on older Frigidaire front-load washer models (ATF, GLTF, FAFW series and others). The 131763302 is a gray color used on newer Frigidaire and Electrolux models. Always compare your existing striker's shape and dimensions to confirm, or contact our support team with your model number.
Should I also replace the door lock assembly when replacing the striker?
Not necessarily — in most cases the striker is the only part that needs replacement. The striker is a small plastic tab that takes repeated impact every time the door is closed, making it the most commonly worn part in the door latch system. The door lock assembly (131763202) is more durable and less prone to failure. Inspect the door lock for any cracks, burn marks, or a latch that does not spring back after pressing — if it appears damaged, replace it as well. If the lock looks intact, the 131763310 striker alone should resolve the issue.
My washer door closes but the washer still won't start — is it the striker?
It may be. If the striker is cracked, worn, or broken, it may appear to engage the door lock but not push far enough into the lock assembly to fully activate the door switch. In other cases, a fully intact striker may not be the cause — the door lock assembly itself (131763202) or the door latch on the frame side may also be the culprit. Visually inspect the striker first — if it is visibly broken, replace it. If it appears intact, the issue may be with the door lock assembly or wiring.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 131763310 door striker.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
DC97-19289F Genuine OEM Samsung Washer Drain Pump Assembly
The DC97-19289F is a Genuine OEM Samsung replacement washer drain pump assembly compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA48, WA50, WA52, and WA54 series, as well as select Kenmore models built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will display error codes 5C, SE, nd, 5E, FO2, or E5, leave standing water in the tub, stop mid-cycle, or produce unusual noise during draining.
This complete drain pump assembly is rated 120V, 60Hz, 80W, 1.1A with a 30-minute on / 30-minute off duty cycle. It directly replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01. Note: the wire plug on the new pump may differ slightly from the original — if the connector does not match your washer's harness, transfer the wiring harness from the old pump to the new one. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The DC97-19289F Genuine OEM Samsung Washer Drain Pump Assembly fixes Samsung top-load washers displaying error codes 5C, SE, nd, 5E, FO2, or E5, not draining, leaving standing water, or making loud noise during the drain cycle. 120V/60Hz/80W/1.1A, 30 min on/30 min off duty cycle. Compatible with Samsung WA40 through WA54 series and Kenmore (Samsung-built). Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, PX3516-01. Note: if wire plug differs, transfer harness from old pump.
Common Problems This Part Fixes
Error codes 5C, SE, nd, 5E, FO2, or E5 — washer cannot drain within the allotted time
Washer not draining — standing water remaining in the tub after a cycle
Washer stopping mid-cycle due to a drain fault
Loud humming, grinding, or rattling noise during the drain cycle
Water draining very slowly — worn pump motor below rated performance
Water leaking from the drain pump area at the bottom of the washer
Pump running continuously but water not being expelled from the tub
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
DC97-19289F, DC97-17349B, DC97-19289B,DC97-17366A, DC97-17366J, DC97-19289A,ASM772133, AP6806651, EAP12592631, PD00049911, PX3516-01, PS12592631.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select top-load washers from the following brands and series:
Samsung top-load washers — WA40 series (WA400PJHDWR and related models)
Samsung top-load washers — WA41 series (WA41A3000AW and related models)
Samsung top-load washers — WA42 series
Samsung top-load washers — WA44 series (WA44A3205AW and related models)
Samsung top-load washers — WA45 series (WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW and related models)
Samsung top-load washers — WA48 series (WA48H7400AW and related models)
Samsung top-load washers — WA50 series (WA50F9A7DSP, WA50M7450AW and related models)
Samsung top-load washers — WA52 series (WA52M7750AW, WA52M8650AW and related models)
Samsung top-load washers — WA54 series (WA54M8750AV and related models)
Samsung top-load washers — WA456DRHDSU series
Kenmore / Sears top-load washers (select Samsung-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Removes water from the tub during the drain and spin cycles for proper washer operation
Resolves Samsung error codes 5C, SE, nd, 5E, FO2, and E5 caused by drain pump failure
Rated 120V, 60Hz, 80W, 1.1A — correct electrical specifications for compatible Samsung top-load models
30-minute on / 30-minute off duty cycle — matches the operational requirements of compatible models
Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01
Wire plug may differ from original — transfer harness from old pump if connector does not match
Compatible with Samsung WA40 through WA54 series and Kenmore Samsung-built top-load washers
Genuine OEM part manufactured by Samsung to factory specifications — guaranteed fit and performance
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
DC97-19289F
Also Replaces
DC97-19289A, DC97-19289B (prior versions)
Part Type
Washer Drain Pump Assembly
Condition
Genuine OEM
Application
Samsung Top-Load Washers
Voltage
120V AC
Frequency
60 Hz
Wattage
80W
Amperage
1.1A
Duty Cycle
30 minutes on / 30 minutes off
Error Codes Resolved
5C, SE, nd, 5E, FO2, E5
Connector Note
Wire plug may differ — transfer harness from old pump if needed
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Tilt the washer back or lay it on its side to access the drain pump at the bottom of the machine. Place towels and a shallow pan to catch residual water when the pump is disconnected. Note the wiring connector orientation before disconnecting — take a photo if needed. If the new pump's connector does not match the washer's harness, carefully transfer the wiring harness from the old pump to the new pump. Disconnect the drain hoses from the pump using pliers to loosen the clamps. Unscrew the pump mounting screws and remove the old pump. Install the new DC97-19289F pump in the same position, reconnect drain hoses and secure with clamps, and reconnect the wiring harness. Restore water supply and power, then run a drain cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels.
Frequently Asked Questions
What error codes indicate a drain pump failure on Samsung washers?
Error codes 5C, SE, nd, 5E, FO2, and E5 on Samsung top-load washers all indicate a drain fault — the washer was unable to drain within the expected time. These codes can also be caused by a clogged drain filter, blocked hose, or kinked drain line, so check those first. If the filter and hose are clear and the error persists after clearing them, the drain pump is the most likely cause.
What is the difference between DC97-19289F, DC97-19289A, and DC97-19289B?
These are successive revisions of the same Samsung drain pump assembly. DC97-19289A was the original version, DC97-19289B was an update, and DC97-19289F is the current version. Samsung issues revised part numbers when minor production changes are made — all three perform the same function and the DC97-19289F is the correct current replacement for any of the earlier versions. The DC97-17349B, DC97-17366A, and DC97-17366J are additional older cross-references for this pump used on earlier Samsung top-load models.
Why might the wire plug on the new pump differ from the original?
Samsung revised the wiring connector on this drain pump across different production runs. If the DC97-19289F pump you receive has a different connector than your washer's harness, do not force the connection. Instead, carefully remove the wiring harness from the old pump and transfer it to the new pump — both versions use the same internal terminals and the harness swap is straightforward. This is a known and documented step for this part and does not affect performance or safety.
Should I check the drain filter before replacing the pump?
Yes — always check and clean the drain filter and inspect the drain hose for kinks or blockages before replacing the pump. A clogged filter or blocked hose can cause the same error codes as a failed pump and clearing the blockage may resolve the problem without needing a new part. On Samsung top-load washers the drain filter is typically located at the bottom front of the machine. If the filter and hose are clear and the error persists, the pump needs replacement.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by Samsung to factory specifications. It is the exact same drain pump assembly installed in compatible Samsung and Kenmore top-load washers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
DC31-20014C Washer Genuine OEM Shift Actuator
This clutch (part number DC31-20014C) is for washers. Clutch DC31-20014C spins the basket during the spin cycle.
Fits specific Samsung washer Models
Replaces Part Numbers:DC31-20014C, 2068406, AP4211210, PS4204941.
California Residents only: WARNING: California’s Proposition 65
XPARTCO 8572717 Washer Motor Start Capacitor
The XPARTCO 8572717 is an aftermarket replacement motor start capacitor for Whirlpool-built top-load washers and washer/dryer combination units. Unlike a run capacitor that stays in the circuit continuously, this start capacitor's job is brief and intense: at the instant the motor is commanded to start, it delivers a strong momentary boost of voltage to help the motor overcome its own inertia and get up to speed quickly. Once the motor reaches running speed, a relay switches it out of the circuit, handing off to the run capacitor for continuous operation. That short, high-stress duty cycle is exactly why start capacitors are a common failure point — they work hard for a fraction of a second on every single cycle start.
Rated 189–227 MFD at 125VAC, 60Hz. The capacitor is a black cylindrical component mounted to the rear panel of the washer, held in place by a small plastic retaining clip and wrapped in a foam shield that protects it from moisture. Common failure modes include the internal dielectric breaking down from repeated startup stress, and in some cases the capacitor overheating badly enough to produce visible smoke if it fails while still energized. A failing start capacitor produces a clear symptom: the washer motor hums but won't start, or the motor fails to spin up while other functions of the washer still respond normally. It directly replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006.
Quick Answer
The XPARTCO 8572717 Washer Motor Start Capacitor fixes Whirlpool-built top-load washers and washer/dryer combos where the motor hums but won't start, the washer won't agitate or spin, or there's a burning smell from the motor area. Includes foam shield. 189–227 MFD, 125VAC, 60Hz. Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling.
Common Problems This Part Fixes
Washer motor hums but won't start
Washer won't agitate
Washer won't spin or drain because the motor never starts
Burning smell coming from the motor area
Washer that starts a cycle but the drum never begins moving
Motor that struggles to start under load but may start when the drum is empty
Visible discoloration, bulging, or a burnt smell from the capacitor itself
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer motor start capacitor directly replaces the following OEM and cross-reference part numbers:
8572717, WP8572717, 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This motor start capacitor is compatible with select Whirlpool-built top-load washers and washer/dryer combination units across the Whirlpool family of brands, including:
Whirlpool top-load washers and washer/dryer combos — WET, WGT series
Kenmore top-load washers (select Whirlpool-built 110-series models)
Maytag, KitchenAid, Jenn-Air, and Amana washers (select models)
Roper, Admiral, Hardwick, and Estate washers (select models)
Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric washers (select models)
Select Ikea washers built on the Whirlpool platform
Verified model numbers include: WET4027EW, WET4024EW, LTE5243DQ, WET3300XQ, WGT3300XQ, MTW5670TQ0, SAWS800JQ1, LSN7233BW1, LSR7233DZ1, LSQ8243HQ0, LSQ8512KQ0, LSQ8543JQ0, LSQ8543JQ1, LSQ8543JT0, LSQ8543JT1, LSQ9244EQ0, LSQ9544KQ0, LSQ9549LG0, LSQ9549LG1, LSQ9549LG2, LSQ9549LG3, LSQ9549PW2, 8LSC6244BQ0, and Kenmore 110.72407600, 110.72408440, 110.74414130, 110.81360430, 110.82074620, 110.82984100, 110.91565810, and 110.98573110.
Note: This capacitor fits both standalone washers and Whirlpool washer/dryer combination units. Always verify your full model number before ordering, since specifications and mounting can vary by platform. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement start capacitor — delivers a momentary voltage boost to get the washer motor spinning at startup
Resolves "motor hums but won't start," "won't agitate," "won't spin," and "burning smell" symptoms caused by capacitor failure
Rated 189–227 MFD, 125VAC, 60Hz
Includes foam shield to protect against moisture — transfer or reuse per your model's original configuration
Direct drop-in replacement — mounts to the same rear panel retaining clip
Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and related top-load washers and washer/dryer combos
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
8572717
OEM Part Number
WP8572717
Part Type
Washer Motor Start Capacitor
Condition
Aftermarket Replacement
Application
Top-Load Washers / Washer-Dryer Combos (Whirlpool-Built)
Capacitance
189–227 MFD (µF)
Voltage
125VAC
Frequency
60 Hz
Shape
Cylindrical (black)
Included Components
Foam moisture shield
Mounting
Rear panel, plastic retaining clip
Quantity
1 start capacitor
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Ikea
Installation Notes
⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Unplug the washer or shut off the house circuit breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching either terminal, discharge the capacitor by shorting its two terminals together using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified appliance technician replace this part instead.
⚠️ Transfer The Foam Shield To The New Capacitor Wear work gloves. Remove the washer's console and then the spring clips that secure the top/body assembly to the washer frame, using a putty knife to gently release them. With the body lifted or set aside, locate the capacitor — a black cylindrical component mounted to the rear panel, held in place by a small plastic retaining clip. Using a flat-blade screwdriver, gently pop the plastic clip away from the capacitor to release it. After confirming the capacitor is fully discharged, unplug it from the appliance wiring. Remove the foam shield from the old capacitor and transfer it onto the new one before installing — this shield protects the capacitor from moisture, and skipping it leaves the new part more exposed to washer humidity. Connect the new 8572717 capacitor to the wiring, snap it back into the plastic retaining clip in the same position, and reassemble the body, spring clips, and console in reverse order. Restore power and run a test cycle to confirm the motor starts promptly on both agitate and spin. Tools needed: putty knife, flat-blade screwdriver, Phillips screwdriver, insulated-handle screwdriver or capacitor discharge tool, work gloves.
Frequently Asked Questions
My washer motor hums but won't start. Is this the right part?
Yes, this is the classic symptom of a failed start capacitor. Since this capacitor's entire job is delivering the momentary voltage boost needed to get the motor spinning from a standstill, a failure here often leaves the motor energized and humming but unable to actually overcome its own inertia and start turning.
What's the difference between a start capacitor and a run capacitor?
A start capacitor works only for a brief moment — it delivers a strong voltage boost the instant the motor is told to start, then a relay switches it out of the circuit once the motor reaches running speed. A run capacitor, by contrast, stays in the circuit continuously while the motor operates, correcting current phase for efficiency. Because the start capacitor works so hard in such a short burst on every single start, it's a more common failure point than a run capacitor on this type of motor.
Do I need to reuse the foam shield from my old capacitor?
Yes, it's worth transferring. The foam shield wraps around the capacitor to protect it from moisture inside the washer cabinet, and reusing it on the new capacitor helps the replacement hold up the same way the original was designed to. If the foam has degraded significantly, you can skip it, but it's a simple step that adds meaningful protection.
My old capacitor got hot and smoked. Is that dangerous?
Yes — a capacitor that overheats to the point of smoking has failed in a way that can pose a fire or electrical hazard, and the washer should not be used again until it's replaced. This kind of failure typically happens when a capacitor stays energized longer than it should, generating heat it isn't designed to dissipate. Replace the capacitor and, if the washer's start relay or timer seems to be holding the capacitor in the circuit too long, have that checked as well.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (189–227 MFD, 125VAC, 60Hz), cylindrical form factor, and mounting configuration of the original WP8572717 start capacitor used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, and related top-load washers and washer/dryer combos.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 3405-001034 Microwave Door Switch (Normally Open)
The XPARTCO 3405-001034 is an aftermarket replacement normally open (NO) microwave door interlock switch for select Samsung, Whirlpool, Maytag, Kenmore and other microwave ovens, replacing part 3405-001034. The switch detects when the door is fully closed and completes the safety circuit, so the microwave runs only when the door is shut. When it fails, the microwave may not start, may not heat, or may only run if you push or jiggle the door.
Microwaves often use more than one door switch, and each is sold individually. Check that the switch you are replacing is the normally open type and goes in the same position.
⚠️ Critical Safety Part — Switch Type And Position Must Match Exactly Door interlock switches work together as a safety system. Installing the wrong type (normally open vs. normally closed) or putting a switch in the wrong position can let the microwave run with the door open, a serious radiation hazard. Replace each switch with the exact same type in the exact same position, and test the microwave after replacement. If you are not qualified to service microwave ovens, use a trained technician.
Quick Answer
The XPARTCO 3405-001034 Microwave Door Switch (Normally Open) replaces a failed normally open door interlock switch on a compatible microwave. Replaces 3405-001034 and 3405-000178. Classic symptoms: the microwave won't start, won't heat, or only runs when you push or jiggle the door.
Common Problems This Part Fixes
Microwave won't start
Microwave runs but doesn't heat
Microwave only works if you push or jiggle the door
Microwave doesn't shut off properly when the door opens
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This microwave door switch directly replaces the following part numbers:
3405-001034, 3405-000178, AP4044834, ASM392474, EAP11741686, PD00025810, PS4131192, WP3405-001034, AP6008546, AWP47167, PD00078424, PS11741686
Samsung also uses nearby numbers, such as 3405-001033, for different switches. They are not interchangeable by number alone. If your old switch shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This switch is listed for Samsung, Whirlpool, Maytag, Amana, Jenn-Air, Kenmore and Magic Chef microwave ovens and microwave/oven combinations, including these examples:
Kenmore 40180082010, 40180099700, 40185042010
Samsung SMH1622W
Note: The models above are a small sample of those listed by retailers. Confirm that your original switch is normally open and goes in the same position, check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Normally open (NO) microwave door interlock switch
Aftermarket replacement for Samsung and Whirlpool 3405-001034
Completes the safety circuit only when the door is fully closed
Sold individually, one switch per order
Product Specifications
Part Number
3405-001034
OEM Part Number
3405-001034
Part Type
Microwave Door Interlock Switch
Condition
Aftermarket Replacement
Switch Type
Normally Open (NO)
Application
Select Microwave Ovens and Microwave/Oven Combinations
Installation Notes
⚠️ Unplug Microwave And Beware Of The High Voltage Capacitor Unplug the microwave before starting and never operate it with the cabinet open. The high voltage capacitor can hold a lethal charge even after the microwave is unplugged. If your repair requires removing the outer cabinet, discharge the capacitor safely first, or have a qualified technician do the work.
⚠️ Photograph Switch Positions Before Removing Anything The switches are accessed at the door latch assembly. Before disconnecting anything, photograph each switch and its wiring, and move the wires one at a time so each goes back to the correct terminal. Make sure the actuator lines up with the latch and the switch clicks freely. After reassembly, test the microwave with a microwave-safe cup of water.
Frequently Asked Questions
My microwave won't heat or start. Is this the part I need?
A failed door switch is a common cause, but a microwave has several switches and other parts can cause the same symptoms. Identify which switch failed and confirm it is normally open before ordering.
Is this switch normally open or normally closed?
This is a normally open (NO) switch. It is not interchangeable with normally closed switches, which do a different job in the interlock system.
Is this an OEM or aftermarket part?
This is an aftermarket replacement from XPARTCO, made to replace part 3405-001034. If you specifically need a genuine part, contact our support team.
Will this fit my microwave?
It is listed for many Samsung, Whirlpool, Maytag and Kenmore models, but the model list above is only a sample. Check your full model number and the type and position of your original switch, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM WPW10453947 Washer or Dryer Control Knob
The Genuine OEM WPW10453947 is a factory-original control knob used on both washers and dryers across the Whirlpool platform — the same knob design is shared between select top-load washer cycle-selector dials and dryer cycle/timer dials, depending on the model. It mounts onto the control shaft on the console and is what the user grips to select a wash or dry cycle. Over time these knobs commonly crack, the D-shaped shaft-grip inside wears out and starts spinning freely on the shaft, or the knob's pointer/indicator fades or breaks off.
As the genuine Whirlpool part, it matches the factory shaft profile, detent feel, and indicator marking of the original equipment, so there's no fit or cosmetic mismatch. It directly replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Installs in under 5 minutes with no tools required — it's a simple push-on friction fit in most applications.
Quick Answer
The Genuine OEM WPW10453947 Washer or Dryer Control Knob fixes Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers with a cracked, spinning, or missing cycle-selector knob. This is the factory-original Whirlpool knob — not an aftermarket equivalent — and is used on both washer and dryer control panels depending on model. Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Classic symptom: knob spins freely on the shaft without turning the dial, or won't stay in the selected cycle position.
Common Problems This Part Fixes
Control knob spins freely on the shaft without engaging the dial underneath
Knob is cracked, chipped, or has broken retaining tabs on the back
Knob won't stay pointed at the selected cycle
Indicator marking or pointer on the knob is faded, worn, or broken off
Knob is missing entirely, making it difficult to select a cycle
Knob feels loose or wobbly on the control shaft
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This control knob directly replaces the following OEM and cross-reference part numbers:
W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This control knob is compatible with select washer and dryer models from the following brands:
Whirlpool washers and dryers (including WTW4616FW1, NTW4700YQ0, and related models)
Amana washers and dryers (select models)
Admiral washers and dryers (select models)
Inglis washers and dryers (select models)
Roper washers and dryers (select models)
Kenmore washers and dryers (select Whirlpool-built models)
Crosley washers and dryers (select models)
Maytag washers and dryers (select Whirlpool-built models)
Note: This same knob is used across hundreds of washer and dryer model numbers on both appliance types. Always verify fit using your appliance's exact model number before ordering, since visually similar knobs with a different shaft profile are used on other platforms. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM control knob — factory-original fit, feel, and appearance
Used on both washer and dryer control panels across the Whirlpool platform
Resolves "knob spins freely," "cracked knob," and "missing cycle indicator" symptoms
Matches original detent feel and cycle-position indicator
Push-on friction fit — no tools required for installation
Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979
Compatible with Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers
Genuine OEM part — factory-specified materials and markings
Product Specifications
Part Number
WPW10453947
OEM Part Number
WPW10453947
Part Type
Washer / Dryer Control Knob
Condition
Genuine OEM Replacement
Application
Washer or Dryer Cycle-Selector Control Panel
Mounting
Push-on friction fit to control shaft
Compatible Brands
Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, Maytag
Installation Notes
ℹ️ No Tools Required — Unplug Appliance First Disconnect power to the washer or dryer before beginning. Note the current cycle position of the old knob before removing it, so you can align the new one the same way. Grip the old knob firmly and pull straight outward, away from the console, to release it from the friction fit on the shaft. If it's cracked and difficult to grip, work a flat-blade screwdriver gently behind the knob's edge to help pry it free, taking care not to damage the console. Line up the new WPW10453947 knob's D-shaped (or splined) center opening with the flat side of the control shaft, and press straight in until it seats fully against the console. Restore power and test that the knob turns smoothly through each cycle position and the indicator lines up correctly.
Frequently Asked Questions
Is this knob for a washer or a dryer?
Both — this is a shared control knob design used on select Whirlpool-platform washers and dryers, depending on the model. The knob itself is identical; what it controls (wash cycle vs. dry cycle) depends on which appliance and console it's installed in. Confirm your appliance's model number before ordering to make sure this is the correct knob for your specific control panel.
My knob spins freely and doesn't change the cycle — is this the fix?
Yes, in most cases. This happens when the knob's internal shaft-grip (the D-shaped or splined opening that mates with the control shaft) wears out or cracks, so the knob spins independently of the shaft underneath it. Replacing the knob restores a snug grip on the shaft so turning it actually moves the selector.
Do I need any tools to install this?
No — it's a simple push-on friction fit. Pull the old knob straight off the shaft (a flat-blade screwdriver can help pry a stuck or cracked one loose) and press the new one on, matching the shaft's flat side to the knob's opening. No screws or fasteners are involved.
Is this a genuine Whirlpool part or an aftermarket equivalent?
This is the genuine, factory-original Whirlpool knob — not an aftermarket equivalent. It matches the original shaft profile, detent feel, and cycle-indicator markings, so there's no mismatch in fit or appearance versus the original equipment.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine Whirlpool OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM 5220FR2075V Washer Water Valve
The Genuine OEM LG 5220FR2075V is the water inlet valve assembly for select LG and Kenmore front-load washers. The valve connects your home's water supply to the washer and opens and closes under control of the washer's control board, letting water into the tub and the detergent dispenser during each cycle. When it fails, the washer may fill slowly, fill with the wrong water, fill continuously, or not fill at all.
This is the original LG part. LG lists 5221ER1003M as an alternate number for this valve. Because LG makes several look-alike inlet valves that differ in coil count and connections, check your model number before ordering.
Quick Answer
The Genuine OEM 5220FR2075V Water Inlet Valve fixes an LG or Kenmore front-load washer that won't fill, fills slowly, fills with the wrong water temperature, or leaks or keeps filling at the valve. LG also lists it as 5221ER1003M. Classic symptom: the washer starts the cycle but stays empty or fills very slowly, and the water supply and hoses are fine.
Common Problems This Part Fixes
Washer won't fill with water
Slow filling, or a low water level
Detergent or bleach dispenser doesn't flush
Washer keeps filling or leaks at the valve
Water too hot or too cold because one inlet isn't opening
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This water inlet valve directly replaces the following part numbers:
5220FR2075V, ALG312873, AP7003066, PD00074485, 5221ER1003M, 4869495, ALG51888, AP6334246, EAP12579227, PD00050119, PS12579227
LG's Canadian parts catalog lists 5221ER1003M as an alternate to 5220FR2075V. This is a single-source cross-reference, so confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Similar-looking valves such as 5220FR2075L and 5221ER1003A are different parts and are not interchangeable with this one.
Compatibility
This valve is listed for LG and Kenmore front-load washers, including these examples:
LG WM3400CW, WM3500CW, WM3600HVA, WM3600HWA
LG WM3700HRA, WM3700HVA, WM3700HWA
LG F3L2CYV5T.ASSEVUS, F3P1CYV5T.ASSEVUS
Note: The models above are a sample from retailer listings, not an official full list. LG makes several inlet valves that look alike but differ in coil count and connections, so a wrong match is easy to make. Enter your model number at checkout or contact our support team to verify fit before ordering.
Key Features
Genuine OEM LG water inlet valve assembly
Controls water flow from the supply into the tub and dispenser
Also listed under LG alternate number 5221ER1003M
Resolves no-fill, slow-fill, and continuous-fill problems
Fits select LG and Kenmore front-load washers
Product Specifications
Part Number
5220FR2075V
OEM Part Number
5220FR2075V
Part Type
Washer Water Inlet Valve Assembly
Condition
Genuine OEM
Application
LG & Kenmore Front-Load Washers
Installation Notes
⚠️ Unplug Power and Shut Off the Water Unplug the washer and turn off both water supply valves before beginning. Wear work gloves, and have a towel and shallow pan ready for water left in the hoses. Pull the washer out and remove the rear or top panel as shown in your model's service guide. Disconnect the supply hoses, the wire connectors, and the dispenser hoses from the old valve, noting where each goes. Install the new valve in the same position, reconnect everything, and check for leaks with the water on before pushing the washer back.
Frequently Asked Questions
My washer won't fill. Is this the part I need?
A failed inlet valve is a common cause, but first check that both water supply valves are open and that the inlet screens at the hose connections aren't clogged. If those are fine and the washer still won't fill, the valve is a likely cause.
Is 5220FR2075V the same as 5221ER1003M?
LG's Canadian catalog lists 5221ER1003M as an alternate to 5220FR2075V. This is a single-source cross-reference, so check your model's parts diagram or ask our support team to confirm.
Can I use 5220FR2075L or 5221ER1003A instead?
No. They are different valves, and LG sells several that look alike. Use the number your model calls out, or contact our support team to confirm before ordering.
Will this fit my washer?
It is listed for select LG and Kenmore front-load washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve
The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting.
Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP.
Quick Answer
The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first.
Common Problems This Part Fixes
Washer not filling with water
Washer filling very slowly
Water continuing to leak into the tub after the wash cycle has completed
No hot water reaching the tub, or no cold water reaching the tub
Cycle stalling at the fill step and never advancing to wash
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2.
Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate
Regulates hot and cold water flow into the washer tub
Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP
Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair
Product Specifications
Part Number
W11210459
Part Type
Washer Water Inlet Valve
Condition
Genuine OEM
Brand
Whirlpool
Application
Top-Load Washers
Function
Controls hot and cold water flow into the tub
Repair Difficulty
Moderate
Quantity
1 valve
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper
Installation Notes
⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves.
Frequently Asked Questions
My washer isn't filling with water. Is this the right part?
Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding.
What's the easiest way to access the control panel for this repair?
Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial.
Is this the same as W11210463?
No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
