Search results for "dryer igniters and gas valves"

Genuine OEM WP697772 Dryer Blower Wheel The WP697772 is a genuine OEM blower wheel from Whirlpool for Whirlpool-built dryers and washer-dryer combos sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral names. The blower wheel attaches to the drive motor shaft and moves air over the heat source, through the drum, and out the exhaust vent. When the wheel wears, cracks, loses a fin, or comes loose on the shaft, the dryer gets noisy and airflow drops, so clothes take longer to dry. This is a genuine OEM part, not an aftermarket equivalent, so the fit and balance match the original. If your dryer is only noisy, check the blower for lint buildup first, since a clogged wheel can sound like a failing one. Quick Answer The Genuine OEM WP697772 Blower Wheel fixes a Whirlpool-built dryer that is noisy, has weak airflow, or takes too long to dry because the blower wheel is worn, cracked, or damaged. Genuine OEM from Whirlpool. Classic symptom: a rattling, thumping, or squealing noise from the back of the dryer, with damp clothes at the end of a normal cycle. Common Problems This Part Fixes Dryer noisy, with rattling or thumping from the blower area Weak airflow, or clothes taking too long to dry Visibly cracked, chipped, or broken blower fins Blower wheel loose or slipping on the motor shaft Wheel worn out over time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This blower wheel replaces the following part numbers: WP697772, WPW10211915, 697772, W10211915, 687613, AP6010627, AWP48289,EAP11743811,  FIX11743811, OEM18031890, PD00003053, PS11743811 These are Whirlpool's un-prefixed and earlier numbers for this blower wheel. If your old wheel or parts diagram shows any of them, match against this list. Compatibility This blower wheel is listed for dryers and washer-dryer combos from: Whirlpool, including CEE2760KQ0, WED9470WW1, and WED9400ST1 Kenmore, including 11060052990, 11060056990, and 10687884100 Maytag, including YMEDX700XL0 and MGDX700AG0 KitchenAid, Amana, Crosley, Inglis, and Admiral Note: The model list above is only a sample, since this wheel fits many more models. Confirm fit by matching the number on your old wheel or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM Whirlpool blower wheel, not an aftermarket equivalent Restores quiet, full airflow through the drum and exhaust Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers and combos Straightforward replacement, typically 15–60 minutes with hand tools Product Specifications Part Number WP697772 OEM Part Number WP697772 Part Type Dryer Blower Wheel Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Family Dryers & Washer-Dryer Combos Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker, and shut off the gas supply first if it's a gas model. Wear work gloves. Following your model's service guide, remove the front cover to reach the blower housing, then the back cover to access the motor shaft. Hold the motor shaft steady while you unscrew the retaining nut and pull off the old wheel. Reviewers report that the nut is left-hand threaded on these dryers, so check the thread direction before forcing it. Thread the new wheel on while holding the shaft, tighten it, and replace the covers. Clean the blower housing and exhaust duct of lint while you have the dryer open, and inspect the new wheel on arrival for damage. Frequently Asked Questions My dryer is noisy. Is this the part I need? Possibly. Before replacing the wheel, check whether it is clogged with lint, which can cause noise and imbalance. If the wheel is clean but cracked, chipped, or loose on the shaft, replace it. Also check the drum rollers and idler pulley, which can make similar sounds. Is the nut on the shaft left-hand threaded? Reviewers report that it is on these dryers, so turn it the opposite way to a normal nut when removing the old wheel. Check on your dryer before applying force. My old wheel is marked 697772 or W10211915. Will this work? Yes. Both numbers are on the Replaces list. If you're unsure, contact our support team with your model number and we'll confirm. Is this a genuine Whirlpool part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE4M137 Dryer High Limit Thermostat The XPARTCO WE4M137 is an aftermarket replacement high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip. This is a direct-fit aftermarket replacement built to the same temperature rating and mounting as the original thermostat. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause. Quick Answer The XPARTCO WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool. Common Problems This Part Fixes Dryer shuts off a few minutes into a heat-dry cycle Dryer stops early and won't restart until it cools down Intermittent shutdowns during the drying cycle Clothes coming out damp because the cycle keeps cutting short Dryer won't start at all if the thermostat has failed in an open position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M137, WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900 These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct replacement for this component regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including: Kenmore 2661532110, GE 2661532210 Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket high limit thermostat for GE-built dryers Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse Rated to open at approximately 315°F to prevent overheating damage Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number XPWE4M137 OEM Part Number WE4M137 Part Type Dryer High Limit Thermostat (Auto-Reset) Condition Aftermarket Replacement Temperature Rating L315-65F (Opens ~315°F, Auto-Resets on Cooling) Location Upper Right Side of Heater Housing Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure. Frequently Asked Questions My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need? Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause. Is this a one-time fuse like the thermal fuse, or does it reset itself? This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed. Why does my dryer keep tripping this thermostat? Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again. How do I test if this thermostat has failed? With the dryer unplugged, you can test the thermostat with a multimeter for continuity across its terminals at room temperature. No continuity when it should be closed (cool) is a sign it has failed and needs replacement. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WPW10185972 Dryer Timer The Genuine OEM Whirlpool WPW10185972 is the dryer timer, the electromechanical control that advances through your dryer's preset cycles. Its internal contacts open and close the circuits that control heat and the drum motor, so the dryer runs for the right amount of time at the right setting. When the timer fails, the dryer may not start, may not advance through the cycle, or may over-dry or under-dry your clothes. This is the original Whirlpool part, also sold under the older number W10185972. It is listed for Whirlpool-built electric dryers sold as Whirlpool, Maytag, Amana, Admiral, Roper, Inglis, and Crosley. Check the part number before ordering, because a similar timer, WPW10185971, is listed for different models. Quick Answer The Genuine OEM WPW10185972 Dryer Timer fixes a Whirlpool-built electric dryer that won't start, won't advance through its cycle, or over-dries or under-dries because the timer has failed. It is also listed as W10185972. Classic symptom: the dial turns but the dryer doesn't run or doesn't engage all the cycle selections. Common Problems This Part Fixes Dryer won't start or won't turn on Dryer doesn't engage all cycle selections Dryer over-dries or under-dries clothes Timer dial doesn't advance through the cycle Heat or motor runs at the wrong time in the cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer timer directly replaces the following part numbers: WPW10185972, W10185972, 1481701, WPW10185972VP, 418-617-20-B5, AP6016537, AWP49431, EAP11749827, PD00002683, PS11749827 W10185972 is the older Whirlpool number. No other cross-reference numbers were confirmed. The similar timer WPW10185971 is a different part and is not listed as interchangeable. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This timer is listed for Whirlpool, Maytag, Amana, Admiral, Roper, Inglis, and Crosley electric dryers, including these examples: Whirlpool 4KWED4750BQ1, Maytag 4KMEDC100BQ1, Amana 4KNED4400BQ1, Amana NED5100TQ1 Admiral AED4475TQ1, YAED4475TQ1, Crosley CEDX631VQ1 Inglis IED4400VQ1, YIED4400VQ1, Roper RED4400VQ1, RED4440VQ1, YRED4340SQ2 Note: The models above are a sample from one retailer, not a full list. A similar timer, WPW10185971, is listed for different dryer models (such as Admiral AGD4475TQ1 and Amana NGD5100TQ1), so check which number your model calls out. Confirm your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool dryer timer Advances through preset cycles and switches heat and motor circuits Also listed under the older number W10185972 Resolves no-start, cycle-advance, and over- or under-drying problems Fits Whirlpool-built electric dryers sold under many brand names Product Specifications Part Number WPW10185972 OEM Part Number WPW10185972 Part Type Dryer Timer Condition Genuine OEM Application Whirlpool-Built Electric Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning, and wear work gloves. Remove the control panel as shown in your model's service guide to reach the timer. Before disconnecting anything, photograph the wire connections or note the position of each wire, since the timer has many terminals. Move the wires one at a time to the new timer, mount it, replace the knob, and restore power. Test each cycle selection before closing the dryer. Frequently Asked Questions My dryer won't start. Is this the part I need? A failed timer is a common cause, especially if the dial turns but the dryer doesn't run or doesn't engage every cycle selection. The door switch, start switch, and thermal fuse can cause the same symptom, so check those first. Is WPW10185972 the same as W10185972? Yes. W10185972 is the older Whirlpool number for the same timer, and this part covers both numbers. Can I use WPW10185971 instead? No, don't assume so. WPW10185971 is a separate timer listed for different models. Use the number your model calls out, or contact our support team to confirm before ordering. Will this fit my dryer? It is listed for many Whirlpool-built electric dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10169881 Dryer Genuine OEM Thermostat Kit Description: This Dryer thermostat kit is an OEM replacement part responsible for ensuring the safety and temperature regulation of the dryer. The high-limit thermostat serves as a critical safety device that monitors and regulates the temperature inside the dryer. When the temperature rises to a level beyond the safe operating range, the high-limit thermostat interrupts the flow of electricity to the heating element. The thermal cut-out fuse, included in this kit, offers an additional layer of protection by disconnecting power to the heating element if it detects excessively high temperatures. Replaces Part Numbers: W10169881, 1455409, AH1964653, EA1964653, AP4316800, PS1964653.    California Residents only WARNING: California’s Proposition 65

Read more less

W11568627 Genuine OEM Whirlpool/Kenmore Dryer Drum Belt The W11568627 is a genuine OEM drum (cylinder) belt for select Whirlpool and Kenmore front-load dryers. This belt wraps around the outside of the drum and routes around the drive motor pulley and idler pulley — it's what actually spins the drum during a drying cycle while the motor and blower keep running independently. Over time this belt stretches, glazes, or cracks from heat and friction, and it eventually slips or snaps, leaving the drum motionless even though the rest of the dryer still runs. Manufactured by Whirlpool to factory spec for smooth, durable drum operation under high-demand drying cycles, this is a genuine OEM part — not an aftermarket equivalent — so fit and long-term performance match what came on the dryer originally. Quick Answer The Genuine OEM W11568627 Dryer Drum Belt fixes a Whirlpool or Kenmore dryer whose drum won't spin, or that runs with a rubbing/thumping noise from the drum area. Genuine OEM replacement, factory fit. Classic symptom: motor and airflow run normally, but the drum sits still — or a rubbing sound right before the belt fails completely. Common Problems This Part Fixes Dryer runs (motor and airflow work) but the drum doesn't spin Rubbing, squealing, or thumping noise from inside the dryer during operation Clothes bunch up in one spot instead of tumbling Burning rubber smell from a slipping or overheating belt Visible cracking, glazing, or fraying on the old belt Dryer drum spins freely by hand with no resistance from the motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part number: W11568627, W10577771, AP7175918, AWP45299, EAP16660508, OEM21527763, PD00070745, PS16660508 W10577771 is the previous Whirlpool part number for this belt; W11568627 is the current production number. We were not able to confirm additional cross-reference numbers beyond these two at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with the following Whirlpool and Kenmore dryer models: 11061632610, 11061632611 11061633610, 11061633611, 11061633612 11071632610, 11071633610, 110C61633610 WED9500EC0, WED9500EW0, WGD9500EC0, WGD9500EW0 Note: Not all applicable models are necessarily listed above — this is the compatibility data we were able to confirm from available sourcing, and Whirlpool may use this belt on additional models not shown here. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering. Key Features Genuine OEM drum belt — factory fit and durability, not an aftermarket equivalent Drives drum rotation during the drying cycle Built for smooth, reliable operation under high-demand drying cycles Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms Direct replacement for both W11568627 and the earlier W10577771 numbering One-year manufacturer replacement warranty on genuine parts Product Specifications Part Number W11568627 OEM Part Number W11568627 Part Type Dryer Drum (Cylinder) Belt Condition Genuine OEM Application Whirlpool & Kenmore Dryers Country of Origin Mexico Installation Notes ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's front or rear access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel. Frequently Asked Questions My dryer runs but the drum won't turn — is this the part I need? Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless. Is W10577771 the same belt as W11568627? Yes. W10577771 was the earlier Whirlpool part number for this belt; W11568627 is the current production number for the same design. If your dryer's parts diagram shows W10577771, this part is the correct current replacement. My exact model isn't listed — will this still fit? Possibly. Whirlpool uses this belt across a range of models beyond what's confirmed in our current compatibility data. Contact our support team with your full model number and we'll verify fit before you order. Do I need to replace the idler pulley at the same time? Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB13K10003 Surface Burner Spark Electrode The XPARTCO WB13K10003 is an aftermarket replacement spark electrode for the surface burners on GE, Hotpoint, and Kenmore gas ranges. The electrode is the small ceramic-tipped component mounted at the burner head that actually creates the spark: when you turn the burner knob, the range's spark module sends a rapid series of high-voltage electrical pulses to the electrode, which arcs across a small gap to the metal burner cap. That spark ignites the gas flowing from the burner, and the clicking sound you hear while the knob is turned is literally the sound of that spark firing over and over until the burner catches. Because the electrode's ceramic insulator is what keeps that high-voltage pulse contained to a precise spark path, even small damage matters: a hairline crack in the ceramic can let voltage leak to ground instead of arcing at the tip, carbon and grease buildup on the tip can insulate it just enough to weaken the spark, and the metal tip itself can corrode or erode after years of sparking. A failing electrode typically shows up as a burner that clicks normally but is slow to catch, catches with a small "whoof" as gas builds up before ignition, or doesn't spark at all while the other burners on the same range work fine. It directly replaces AP2020574, 244911, AH231266, EA231266, and PS231266. GE's internal part number for this electrode is WG02F05048. Quick Answer The XPARTCO WB13K10003 Surface Burner Spark Electrode fixes GE, Hotpoint, and Kenmore gas ranges where a specific burner clicks but won't light, sparks weakly or intermittently, or ignites with a delayed "whoof" instead of catching right away. Ceramic-tipped spark electrode for the surface burner. Replaces AP2020574, 244911, AH231266, EA231266, PS231266. If a burner doesn't click at all, the problem is more likely the spark module or igniter switch — not this electrode. Common Problems This Part Fixes A specific surface burner clicks but won't ignite, while other burners work fine Burner sparks weakly, intermittently, or only from certain knob positions Delayed ignition — a noticeable pause with gas smell before the burner catches with a "whoof" Clicking sound that continues well after the burner has already lit Visible carbon buildup, grease, or discoloration on the electrode tip Cracked, chipped, or damaged ceramic insulator visible at the base of the electrode Electrode tip that looks corroded, pitted, or eroded compared to a new one No spark at all from one specific burner position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This surface burner spark electrode directly replaces the following OEM and cross-reference part numbers: WB13K10003, WG02F05048, AP2020574, 244911, AH231266, AGE261531, PD00035924, EA231266, PS231266 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This spark electrode is compatible with select gas surface burners on ranges from the following brands: GE gas ranges — EGR2000, EGR3000, and EGR3001 series GE gas ranges — J2B900 and JGB910 series GE gas ranges — JGBP27 series Hotpoint gas ranges (select GE-built models) Kenmore gas ranges (select GE-built models) Westinghouse, Monogram, Café, Moffat, and Profile gas ranges (select GE-built models) Verified model numbers include: EGR2000EC0BB, EGR2000EC0CC, EGR2000EC0WW, EGR2000EC1BB, EGR2000EC1CC, EGR2000EC1WW, EGR3000ED0BB, EGR3000ED0CC, EGR3000ED0WW, EGR3000ED1BB, EGR3000ED2BB, EGR3000ED3BB, EGR3000EH1BB, EGR3001ED1SS, EGR3001ED2SS, EGR3001ED3SS, EGR3001EF1SS, EGR3001EH1SS, J2B900BEF1BB, J2B900CEF1CC, J2B900SEF1SS, J2B900SEF2SS, J2B900WEF1WW, JGB910BEC1BB through JGB910BEC4BB, JGB910CEC1CC through JGB910CEC4CC, JGB910SEC1SS through JGB910SEC3SS, JGB910WEC1WW through JGB910WEC4WW, and the JGBP27BEA1AD through JGBP27BEA5AD range. Note: GE uses several visually similar spark electrodes across its gas range lineup that differ in overall length and mounting angle — for example, a related electrode sold under WB13K10014 is used on other burner positions and model platforms. Some customers have reported this electrode arriving slightly longer than the original but still fitting with room to spare; if your range has very tight clearance underneath, verify your exact model number and burner position before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement ceramic-tipped spark electrode for gas surface burner ignition Directs high-voltage pulses from the spark module into a precise spark path at the burner cap Resolves "clicks but won't light," "weak or intermittent spark," and "delayed ignition" symptoms caused by a worn or damaged electrode Ceramic insulator construction resists heat and contains the spark path Direct drop-in replacement — mounts to the same burner head bracket and wire connector Replaces AP2020574, 244911, AH231266, EA231266, and PS231266 Compatible with GE, Hotpoint, Kenmore, Westinghouse, Monogram, Café, Moffat, and Profile gas ranges Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WB13K10003 OEM Part Number WB13K10003 (WG02F05048) Part Type Gas Range Surface Burner Spark Electrode Condition Aftermarket Replacement Application Gas Range Surface Burner Ignition Tip Material Ceramic-insulated electrode tip Function Directs spark module pulses to ignite burner gas Mounting Burner head bracket with wire lead connector Quantity 1 electrode Compatible Brands GE, Hotpoint, Kenmore, Westinghouse, Monogram, Café, Moffat, Profile Installation Notes ⚠️ Danger — Gas Appliance Turn off the gas supply to the range at the shutoff valve and unplug the range (or shut off its circuit breaker) before beginning any work near the burners or gas line. After reassembly, check every disturbed connection for leaks using a soapy water solution — bubbling indicates a leak. If you ever smell gas at any point during this repair, do not attempt to light the range or operate any switches; leave the area immediately and contact your gas utility or a qualified technician. ⚠️ Handle The Ceramic Insulator Carefully Wear work gloves. Remove the burner grate and burner cap from the affected position to access the electrode underneath. Photograph the electrode's mounting position and wire connection before removing anything. Most electrodes are held in place with a single screw and connect to the spark module via a simple push-on wire terminal — disconnect the wire first, then remove the mounting screw and lift the old electrode free. The ceramic insulator is more fragile than it looks; avoid gripping or prying on it directly, and handle it by the mounting bracket instead. Install the new WB13K10003 in the same position and orientation, making sure the tip sits at the correct gap and angle relative to the burner cap — too far and the spark won't reach the gas port, too close and it can short against the burner base. Reconnect the wire terminal, secure the mounting screw, and reinstall the burner cap and grate. Restore the gas supply and power, then test ignition at that burner position and check for leaks at any connection you touched before considering the job complete. Tools needed: Phillips or flat-blade screwdriver (model-dependent), soapy water for leak testing, work gloves. Frequently Asked Questions My burner doesn't click at all when I turn the knob. Is this the right part? Probably not, at least not by itself. If a burner produces no clicking sound whatsoever, the issue is more likely the spark module (the component that generates the high-voltage pulses) or the igniter switch behind the knob, rather than the electrode itself — an electrode can't spark if it's never receiving a pulse in the first place. This electrode is the right fix when you hear clicking at that burner position but it fails to ignite, sparks weakly, or ignites with a delay. The burner lights but with a small "whoof" and a delay. Is that dangerous? A delayed ignition means gas is flowing and accumulating for a moment before the spark finally catches it, which is exactly the kind of small buildup that produces that "whoof" sound and flare. It's not something to ignore — a weak or intermittent electrode is the common cause, and replacing it restores immediate, reliable ignition. If delayed ignition continues after replacing the electrode, have the burner and gas supply checked by a qualified technician rather than continuing to use it. Can I clean the electrode instead of replacing it? Light cleaning can sometimes help if the tip is coated in grease or food residue — gently wiping the ceramic and metal tip with a dry cloth or a small amount of rubbing alcohol may restore a weak spark caused purely by surface buildup. But if you see a cracked or chipped ceramic insulator, a visibly eroded or pitted tip, or the spark still fails after cleaning, the electrode itself has degraded and cleaning won't fix that — replacement is the correct next step. One burner sparks weakly but the others are fine. Does that rule out the spark module? Yes, generally. The spark module typically drives all the surface burner electrodes from the same unit, so if only one position is affected while the rest spark normally, the shared module is very unlikely to be the cause — the problem is isolated to that one electrode (or its individual wire connection). If every burner is weak or unreliable at the same time, that points toward the spark module instead. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the ceramic insulator design, tip geometry, mounting bracket, and wire connector of the original WB13K10003 electrode used in compatible GE, Hotpoint, and Kenmore gas ranges. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5300622032 Genuine OEM Dryer Heater Restring - Compatible with Frigidaire, Electrolux, Kenmore Product Description Restore optimal drying performance with the 5300622032 Genuine OEM Dryer Heater Restring. This authentic Frigidaire-manufactured heating element restring coil is designed for select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers, generating heat to efficiently dry clothes. Built for durability and precise fit, it addresses issues like no heat or insufficient heat. Note: Includes one heating element restring coil with 1/4" terminals (4600 watts, 240 volts). Does not include heater housing insulators (131472100) or terminal block (3202786). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: 5300622032, 08015672, 3202787, 3281114, AH451031, DE335, EA451031, NQ00622032, Q000622032, Q622032, TJ90DE335, WQ622032, PD00000126, EAP451031, AP2135127, PS451031. Compatibility: Compatible with models including but not limited to: Frigidaire: FDE646GES0, FDE747GES0, FDE847GES0, F31C336ES0, F31C436ES0 Gibson: GSE746RFS0, GSE746RFS1, GDE336RES1, GDE546RES0 Tappan: TDE336RED0, TDE546REW0 Kenmore, Electrolux, Kelvinator, White Westinghouse: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers. 🔧 Specifications: Genuine OEM heating element restring coil, 1/4" terminals, 4600 watts, 240 volts. 💪 Reliable Performance: Authentic Frigidaire part ensures efficient heat generation and long-lasting operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–45 minutes. 🛡️ Effective Fixes: Resolves no heat or insufficient heat in the dryer. Product Specification Part Number: 5300622032 Component Type: Dryer heating element restring coil Material: Metal alloy coil Electrical Rating: 4600 watts, 240 volts Mounting: Fits within existing heater housing, screw-mounted Operating Conditions: Suitable for household dryer environments Compliance: UL listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer heating efficiently today! Add to cart now for a reliable fix!

Read more less

WP3387749 Dryer Genuine OEM Heating Element – Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Restore your dryer’s heating performance with the WP3387749 Dryer Genuine OEM Heating Element. This factory-approved replacement part generates the heat needed to dry laundry efficiently. A failed heating element may cause your dryer to run but not heat, take longer to dry clothes, or shut down during cycles. Replacing it with this genuine OEM part ensures safe operation and long-lasting performance. Replaces Part Numbers WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418. Compatibility This heating element is compatible with select Whirlpool, Kenmore, Maytag dryers. Example compatible models include (but are not limited to): Whirlpool LER4634EQ2, Kenmore 110.96573220, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Wide Compatibility – Fits Whirlpool, Kenmore, Maytag dryers 🔥 Restores Heating – Generates reliable, consistent heat for drying 💰 Cost-Effective OEM Repair – Genuine part ensures durability and performance 🛠️ DIY Friendly – Installs with standard tools in under 30 minutes 🛡️ Fixes Common Issues – Solves no-heat problems, long drying times, or mid-cycle shutdowns 📐 Product Specification Part Number: WP3387749 Component Type: Dryer Heating Element Material: High-temperature resistant metal coil with mounting housing Mounting: Direct replacement heating element assembly Operating Conditions: Designed for residential dryers Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before beginning repairs to prevent electrical shock. Steps: Disconnect power and remove dryer rear access panel. Locate the heating element housing inside the dryer. Disconnect wire terminals and remove screws securing the old element. Slide out defective element and install the new WP3387749. Reconnect wires, secure housing, and reinstall rear panel. Restore power and test dryer heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dryer heating again — Add to Cart Now for a safe, factory-approved repair! WP3387749 Dryer Genuine OEM Heating Element Cross Reference Information   Part Number WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418.

Read more less

Genuine OEM WE4M137 Dryer High Limit Thermostat The WE4M137 is a genuine OEM high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip. This is a genuine OEM part manufactured to the original factory temperature rating and mounting — not an aftermarket equivalent — so trip point and reset behavior match what came on the dryer originally. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause. Quick Answer The Genuine OEM WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Genuine OEM, factory temperature rating, auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool. Common Problems This Part Fixes Dryer shuts off a few minutes into a heat-dry cycle Dryer stops early and won't restart until it cools down Intermittent shutdowns during the drying cycle Clothes coming out damp because the cycle keeps cutting short Dryer won't start at all if the thermostat has failed in an open position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M137 replaces WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900 These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct genuine replacement for this component regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including: Kenmore 2661532110, GE 2661532210 Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models DBXR463ED1WW, DBXR463ED2WW, DBXR463EG7WW, DHDVH52EF0WW, DHDVH66EH0BB, DPSR610EG0WT, DPSR610EG1WT, DPSR610EG2WT, DPSR610EG3WT, DPSR610EG4WT, DPSR610EG5WT, DPSR610EG6WT, DPSR610EG7WT, DPSR610EG8WT, GFDN245EL1MS, GFDS350GL0WW, GFDS350GL1WW, GFDS355EL0MV, GLDP280ED0WS, GLDP280GD0WS, GTDN500EM0WS, GTDN500EM1WS, GTDN500EM2WS, GTDX180ED0WW, GTDX180ED1WW, GTDX180ED3WW, GTDX180ED4WW, GTDX180ED5WW, GTDX180ED6WW, GTDP180ED0WW, GTDP180ED1WW, GTDP200EF1WS, GTDP220EF1WW, GTDP301EL1WS, GTDP490ED0WS, HTDP120ED0WW, HTDX100ED0WW, NBXR333EG1WW, NWXR483EG8WW Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM high limit thermostat — factory fit and trip-point accuracy, not an aftermarket equivalent Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse Rated to open at approximately 315°F to prevent overheating damage Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number WE4M137 OEM Part Number WE4M137 Part Type Dryer High Limit Thermostat (Auto-Reset) Condition Genuine OEM Temperature Rating L315-65F (Opens ~315°F, Auto-Resets on Cooling) Location Upper Right Side of Heater Housing Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure. Frequently Asked Questions My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need? Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause. Is this a one-time fuse like the thermal fuse, or does it reset itself? This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed. Why does my dryer keep tripping this thermostat? Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again. Is this a genuine GE part or an aftermarket copy? This is a genuine OEM thermostat manufactured to the original factory specification — not an aftermarket equivalent — so trip temperature and reset behavior match what came on the dryer originally. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting. Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP. Quick Answer The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first. Common Problems This Part Fixes Washer not filling with water Washer filling very slowly Water continuing to leak into the tub after the wash cycle has completed No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2. Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates hot and cold water flow into the washer tub Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair Product Specifications Part Number W11210459 Part Type Washer Water Inlet Valve Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Function Controls hot and cold water flow into the tub Repair Difficulty Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves. Frequently Asked Questions My washer isn't filling with water. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. What's the easiest way to access the control panel for this repair? Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial. Is this the same as W11210463? No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3390719 Dryer Thermal Fuse – Replaces WP3390719 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe dryer operation and proper heating with the XPARTCO 3390719 Dryer Thermal Fuse. This dryer Thermal Fuse is a replacement part for specific Whirlpool, Kenmore dryer models. This disposable, one-time fuse ensures safe operation of your appliance by cutting off power if the temperature exceeds safe limits. A bad thermal fuse can cause your appliance to stop functioning or prevent it from turning on altogether. Symptoms of a bad thermal fuse include no heat or a dryer that won't start. It is located on the blower housing and cannot be reset. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WP3390719, 3390719, 15-198, 279650, 3389639, 3389640, 660877, 688841, 690198, 690798, 80004, ET402, G4AP0401, PD00002330, EAP11741444, AP6008309, PS11741444. Compatibility This replacement dryer thermal fuse fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley dryers. Commonly installed on the blower housing or exhaust duct, depending on model. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature ratings 🛡️ Overheat Protection – Shuts off power if unsafe temperatures are detected 🔥 Fixes No-Heat or No-Run Issues – Common solution for blown fuse symptoms 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Reliable alternative to OEM thermal fuses 📐 Product Specification Part Number: 3390719 Component Type: Dryer Thermal Fuse Function: One-time over-temperature safety cutoff Application: Blower housing or exhaust system Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear or front access panel (model dependent). Locate the thermal fuse on the blower housing or exhaust duct. Disconnect wires and remove the old fuse. Install the new XPARTCO 3390719 thermal fuse. Reconnect wiring, reassemble panels, and restore power. Test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and reliable operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

4 Pack - XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 - Pack Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less