17438000001584 Genuine OEM Midea Dryer Belt Safety Switch
The 17438000001584 is a Genuine OEM Midea replacement belt safety switch compatible with select Midea, Criterion, and Insignia electric and gas dryers. This safety switch is positioned near the drive belt and tensioner pulley assembly, where it monitors belt-related conditions and interrupts electrical flow to the motor or heating circuit if a fault or unsafe condition is detected — such as a broken or severely slipped drive belt. This is a key safety mechanism: if the belt fails and the drum can no longer be safely driven, this switch helps prevent the motor from continuing to run unsafely or the heater from continuing to operate without normal airflow from drum rotation.
When this switch fails, the dryer may not start, may shut off unexpectedly during operation, or may fail to heat even though other components test correctly. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438000001584 measures 2"L x 2"W x 3"H and weighs approximately 1 oz. It is found on the same parts diagram as the drive belt, tensioner pulley assembly, and drum support components on compatible models. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The 17438000001584 Genuine OEM Midea Dryer Belt Safety Switch fixes Midea, Criterion, and Insignia dryers that won't start, shut off unexpectedly during operation, or fail to heat despite other components testing normally. Mounted near the drive belt and tensioner pulley assembly — interrupts power if a fault or unsafe belt condition is detected. Dimensions: 2"L x 2"W x 3"H, approx. 1 oz. Genuine OEM. Compatible with Midea MLG45N3BMG, Criterion CDG41N1AW, CDG45N1AW, and related Midea-platform dryer models.
Common Problems This Part Fixes
Dryer not starting — safety switch not signaling normal belt/drive conditions
Dryer shutting off unexpectedly partway through a cycle
Dryer not heating despite the heating element, thermostat, and other components testing normal
Dryer behaving erratically after a drive belt failure or replacement
Intermittent power interruption during operation traced to this switch area
Switch contacts failing continuity test with a multimeter
Replaces Part Numbers
This belt safety switch directly replaces the following part number:
17438000001584, AP7157511, PS18188483
This is the Midea manufacturer part number used across multiple Midea, Criterion, and Insignia dryer models. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This belt safety switch is compatible with select Midea, Criterion, and Insignia dryers, including:
Midea MLG45N3BMG gas dryer
Midea MLG45N1BWW, MLG45N3BWW, and related MLG gas dryer series
Midea MLE series electric dryers (select models)
Criterion CDG41N1AW, CDG45N1AW gas dryers (air vent series)
Insignia electric and gas dryers built on the Midea platform (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
Safety switch mounted near the drive belt and tensioner pulley assembly
Interrupts electrical flow to the motor or heating circuit if a fault or unsafe belt-related condition is detected
Compact design: 2"L x 2"W x 3"H, approximately 1 oz
Compatible with Midea MLG/MLE series, Criterion CDG series, and Insignia Midea-built dryers
Installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
17438000001584
Part Type
Dryer Belt Safety Switch
Condition
Genuine OEM
Application
Electric and Gas Dryers (Midea platform)
Dimensions
2"L x 2"W x 3"H
Weight
Approximately 1 oz
Location
Near drive belt and tensioner pulley assembly
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum, drive belt, and tensioner pulley assembly. Locate the belt safety switch in this area — refer to your model's parts diagram to confirm its exact mounting position, as it is positioned near the belt and tensioner pulley support. Photograph the wire connections before disconnecting. Disconnect the wires from the old switch, remove the mounting screw or clip, and pull the switch free. Install the new 17438000001584 switch in the same position, secure the mounting hardware, and reconnect the wires. While this area is open, it's a good time to inspect the drive belt and tensioner pulley for wear, since this switch is related to belt operation. Reassemble the front panel and top panel in reverse order. Restore gas and power, and run a test cycle to confirm the dryer starts and runs normally. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
What does the belt safety switch do?
The belt safety switch monitors belt-related conditions near the drive belt and tensioner pulley assembly and interrupts electrical flow to the motor or heating circuit if it detects a fault or unsafe condition — such as a broken or badly slipped drive belt. This is a protective measure: if the belt has failed and the drum can no longer be driven normally, the switch helps prevent continued unsafe operation of the motor or heater. It works alongside other safety components in the dryer (like the door/cover switch and thermal limiters) as part of an overall safety system.
My dryer just had a belt replacement and now isn't working right — could this switch be involved?
It's possible. Since this switch is positioned near the belt and tensioner pulley assembly, it can be disturbed, dislodged, or its connector improperly reseated during a belt replacement. If your dryer is behaving erratically after a recent belt repair — failing to start, shutting off, or not heating — check that this switch's connector is fully seated and that the switch itself wasn't damaged during the repair. If the connector is good and the switch tests as an open circuit with a multimeter, it has failed and needs replacement.
How do I test if this safety switch has failed?
Unplug the dryer, disconnect the switch's wire connector, and set your multimeter to continuity mode. With the belt and tensioner mechanism in their normal operating position, the switch should show closed continuity (allowing current to flow). If the switch shows an open circuit when it should be closed, it has failed and needs replacement. Always refer to your specific model's wiring diagram to confirm the expected switch state, since exact behavior can vary by dryer model.
Does this switch fit Insignia and Criterion dryers as well as Midea?
Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in certain configurations are manufactured by Midea and use the same internal components, including this belt safety switch. Confirmed Criterion models include the CDG41N1AW and CDG45N1AW gas dryers. Always verify your specific model number before ordering to confirm compatibility.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same belt safety switch installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH11X34740 Washer Genuine OEM Drain Pump Assembly – Compatible with GE & Hotpoint Washers
Product Description
Restore proper draining and reliable washer operation with the WH11X34740 Washer Drain Pump Assembly. This Genuine OEM replacement pump is responsible for removing water from the washer during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud grinding noises, or error codes. Replacing it with this Genuine OEM assembly helps ensure efficient water removal and dependable washing performance.
Replaces Part Numbers
WH23X25518, WH23X10038, WH23X25461, PD00079543, EAP16743374, AP7195487, PS16743374.
Compatibility
This Genuine OEM replacement washer drain pump assembly fits select GE and Hotpoint washers.
Example compatible models include (but are not limited to):
GE GTW465ASNWW, GTW335ASNWW
Hotpoint HTW240ASKWS
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Genuine OEM – Genuine OEM part
💧 Efficient Water Removal – Restores proper draining during cycles
🔇 Quiet Operation – Helps eliminate grinding or buzzing noises
💪 Durable Motor Construction – Designed for long service life
📐 Product Specification
Part Number: WH11X34740
Component Type: Washer Drain Pump Assembly
Voltage: 120V AC
Mounting: Direct-fit, bolt-on installation
Application: Washer drain and spin system
Quality Level: Genuine OEM
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver, pliers
⚠️ Safety First: Unplug the washer and shut off the water supply before servicing.
Basic Steps:
Disconnect washer power and water supply.
Access the drain pump from the bottom or rear of the washer.
Remove hoses and electrical connectors.
Remove mounting screws and take out the old pump.
Install the new WH11X34740 drain pump assembly.
Reconnect hoses and wiring, reassemble panels, and restore power.
Run a test cycle to confirm proper draining.
⏱️ Time Required: 25–35 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!
A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor
The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line.
Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535.
Quick Answer
The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause.
Common Problems This Part Fixes
Dishwasher won't drain at the end of the cycle
Water pooling at the bottom of the tub after a completed cycle
Grinding or humming noise coming from the pump area
Dishwasher won't start a new cycle because it detects leftover water from the previous one
Dishes not getting properly cleaned due to poor water circulation
Pump running but producing little or no actual drainage
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform.
Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Frigidaire OEM part — factory-specified motor speed and impeller design
Pumps water out of the tub and through the drain hose at the end of each cycle
Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure
Includes pump motor, impeller, and seal
Rated 120V, 60Hz, 35W, 0.8A, 3600RPM
1/4" male terminals for a direct plug-in electrical fit
Direct drop-in replacement — no modification required
Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535
Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
A00126401
Part Type
Dishwasher Drain Pump Motor Assembly
Condition
Genuine OEM
Brand
Frigidaire
Voltage
120V
Frequency
60 Hz
Wattage
35 W
Amperage
0.8 A
Motor Speed
3600 RPM
Terminals
1/4" male
Kit Contents
Pump motor, impeller, seal
Dimensions
Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H
Color
White / Green
Repair Difficulty
Easy to Moderate — under an hour
Quantity
1 drain pump motor assembly
Compatible Brands
Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore
Installation Notes
⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves.
Frequently Asked Questions
My dishwasher won't drain. How do I know if it's actually the pump and not something simpler?
Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix.
I already replaced the pump and it's still not draining. What should I check next?
This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing.
Does this kit include the check valve flapper?
This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH11X39237 Washer Drain Pump
The XPARTCO WH11X39237 is an aftermarket replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle.
This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO WH11X39237 Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the drum after a cycle
Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes)
Loud humming, grinding, or buzzing noise during the drain cycle
Washer stopping mid-cycle due to a drain fault
Water leaking from around the drain pump area
Drain pump running continuously but water not being expelled
Pump impeller jammed by debris and motor burned out
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790.
WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part.
Compatibility
This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines:
GE front-load washers — GFW510 series
GE front-load washers — GFW550 series
GE front-load washers — GFW650 series
GE front-load washers — GFW655 series
GE front-load washers — GFW850 series
GE Profile front-load washers — PFW870, PFW950, PFW955 series
GE Profile front-load washers — PFQ83 series
GE 2-in-1 Washer/Dryer Combo (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included
Removes water from the drum during drain and spin cycles for proper washer operation
Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs
Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models
WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539
Direct replacement — installs into existing pump housing with no modification required
Aftermarket replacement built to OEM-equivalent quality standards
Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series
DIY-friendly repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
WH11X39237
Supersedes
WH11X29539 (discontinued)
Part Type
Washer Drain Pump and Filter Assembly
Condition
Aftermarket Replacement
Application
GE Front-Load Washers and 2-in-1 Washer/Dryer Combos
Voltage
120V AC
Frequency
60 Hz
Amperage
1.2A
Includes
Pump motor, impeller housing, and integrated filter
Compatible Series
GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83
Compatible Brands
GE, GE Profile
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels.
Frequently Asked Questions
What is the difference between WH11X39237 and WH11X29539?
These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order.
Should I check the pump filter before replacing the drain pump?
Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step.
How do I know if my drain pump has failed?
A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out.
Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models?
Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical specifications and physical dimensions of the original WH11X39237 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 6501KW2002B Washer Rotor Position Sensor – Compatible with LG and Kenmore Washers
Product Description
Maintain smooth spin cycles and precise motor control with the XPARTCO 6501KW2002B Washer Rotor Position Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly.
Replaces Part Numbers
6501KW2002B, 6501KW2002A, AP7015078, PD00073205, EAP16556422, 4962510, PS16556422, EAP16556422.
Compatibility
This replacement rotor position sensor fits select LG and Kenmore front-load washers.
Example compatible models include (but are not limited to): LG WM2487HRM, LG WM0642HW, and Kenmore 796.40272900.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
Key Features
Aftermarket Replacement – Designed to match OEM performance and precision
Accurate Rotor Feedback – Helps regulate motor speed and direction for smooth washing
Cost-Effective Fix – Delivers OEM-level performance at a fraction of the price
Plug-and-Play Installation – No wiring modification required
Fixes Common Issues – Resolves LE, UE, SE, and spin cycle errors
Product Specification
Part Number: 6501KW2002B
Component Type: Washer Rotor Position Sensor (Hall Sensor)
Material: Durable printed circuit board with reinforced plastic housing
Mounting: Direct-fit installation on stator assembly
Operating Conditions: Rated for high-humidity, high-vibration washer environments
Compliance: Built to OEM-equivalent quality standards (not OEM)
Installation Notes
Tools Needed: 10 mm socket wrench, Phillips screwdriver
⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock.
Steps:
Disconnect power and remove the rear access panel.
Unscrew the rotor bolt and carefully remove the rotor assembly.
Locate and unplug the old sensor from the stator.
Install the new XPARTCO 6501KW2002B sensor, aligning mounting tabs.
Reconnect the wiring harness, reinstall the rotor, and secure the panel.
Restore power and run a spin test to verify correct operation.
⏱️ Time Required: 20–25 minutes
Shop With Confidence
Trusted Appliance Parts Supplier
30-Day Return Policy
Restore precise washer performance — Add to Cart Now for a reliable, budget-friendly repair!
XPARTCO WL49X20360 Washer Motor Speed Sensor Kit – Compatible with GE & Hotpoint Washers
Product Description
Restore accurate motor speed detection and reliable washer operation with the XPARTCO WL49X20360 Washer Motor Speed Sensor Kit. This high-quality aftermarket replacement kit monitors the washer motor’s rotation speed and sends feedback to the control board for proper agitation and spin performance. A faulty speed sensor can cause error codes, no spin, irregular agitation, or cycle interruptions. Replacing it with this XPARTCO kit helps restore smooth operation and consistent wash cycles.
XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price.
Replaces Part Numbers
WL49X20360, WH12X10515, 3031241, PD00025952, EAP8768455, AP5803767, PS8768455.
Compatibility
This replacement washer motor speed sensor kit fits select GE and Hotpoint washers.
Example compatible models include (but are not limited to):
GE GTW465ASNWW, GTW485ASJWS
Hotpoint HTW240ASKWS
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement Kit – Matches OEM fit and signal performance
⚙️ Accurate Motor Speed Feedback – Ensures proper agitation and spin control
🛠️ Direct-Fit Design – No modifications required
💪 Durable Electronic Components – Built for long-term reliability
💰 Cost-Effective Repair – Reliable alternative to OEM sensor kits
📐 Product Specification
Part Number: XPWL49X20360
Component Type: Washer Motor Speed Sensor Kit
Function: Motor rotation and speed detection
Application: Washer drive motor feedback system
Includes: Speed sensor and mounting hardware (as applicable)
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock.
Basic Steps:
Disconnect washer power.
Access the motor area from the bottom or rear of the washer.
Locate and disconnect the old motor speed sensor.
Remove mounting hardware and replace with the new XPARTCO WL49X20360 sensor.
Reconnect wiring and secure the sensor.
Reassemble panels, restore power, and run a test cycle.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore accurate washer motor control and dependable performance — Add to Cart Now for a reliable, budget-friendly repair!
AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly
The AHA72973309 is a genuine LG OEM drain and circulation pump assembly for LG and select Kenmore front-load washers. This is a dual-purpose pump — an Askoll M120-2 unit — that handles two separate jobs from one motor and housing. During the drain portion of the cycle, it pumps wastewater out of the tub and out through the drain hose. During the wash and rinse portions, it switches roles and recirculates water from the bottom of the tub back up through the dispenser and spray nozzle, showering it back over the load. That recirculation spray is what lets LG's front-load washers clean effectively with less water than an older top-load design would need.
Because this single assembly performs both functions, a failure here can show up in more than one way: standing water left in the tub after a cycle, a washer that won't complete its drain step, unusual grinding or humming noise, or reduced wash performance if the recirculation spray isn't working even though draining still seems fine. Common causes include debris such as coins, buttons, or lint lodged in the impeller, general wear and tear on the motor bearings, or an electrical failure in the pump motor itself. It directly replaces AP5676608, 2659237, AHA72973304, and PS7788830. As a genuine OEM part, the AHA72973309 is manufactured by LG to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly fixes LG and select Kenmore front-load washers with standing water left in the tub after a cycle, a washer that won't drain, unusual grinding or humming noise, or reduced wash performance from a weak recirculation spray. Askoll M120-2 dual-purpose pump — handles both draining and mid-cycle water recirculation. Replaces AP5676608, 2659237, AHA72973304, PS7788830. Installation is average difficulty, 30 to 60 minutes — and on many models it's accessible through the front panel without needing to tip the washer over.
Common Problems This Part Fixes
Standing water left in the tub after a cycle finishes
Washer won't drain, or drains very slowly
Drainage-related error code displayed on the control panel
Unusual grinding, humming, or rattling noise during the drain or wash portion of the cycle
Reduced wash performance — clothes not getting as clean, possibly from a weak recirculation spray
Washer stalling mid-cycle at the drain step
Water leaking from underneath the washer near the pump housing
Pump that hums but doesn't seem to move water — possible clog or seized impeller
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drain and circulation pump assembly directly replaces the following OEM and cross-reference part numbers:
AHA72973309, AHA72973304, AP5676608, 2659237, ALG53336, PD00024680, PS7788830
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain and circulation pump assembly is compatible with select LG front-load washers, and also fits select Kenmore and Kenmore Elite front-load washers built on the LG platform.
Note: This is a dual-function drain-and-circulation assembly specific to LG's front-load platform, built around the Askoll M120-2 pump. It is not a drain-only pump, and it is not intended for top-load washers, which use a different pump design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine LG OEM part — factory-specified motor, impeller, and housing design
Dual-purpose Askoll M120-2 pump — drains the tub and recirculates wash water through the dispenser spray nozzle
Resolves "standing water in the tub," "won't drain," "grinding or humming noise," and "reduced wash performance" symptoms caused by pump failure
Includes all necessary wiring and mounting hardware for a complete replacement
Direct drop-in replacement — no modification required
Replaces AP5676608, 2659237, AHA72973304, and PS7788830
Compatible with LG and select Kenmore/Kenmore Elite front-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Average installation difficulty — typically 30 to 60 minutes
Product Specifications
Part Number
AHA72973309
Part Type
Washer Drain & Circulation Pump Assembly
Condition
Genuine OEM
Brand
LG
Pump Model
Askoll M120-2
Function
Drains tub water and recirculates wash water through the dispenser spray
Kit Contents
Pump assembly with wiring and mounting hardware
Application
Front-Load Washers (LG-Built)
Repair Difficulty
Average — 30 to 60 minutes
Quantity
1 pump assembly
Compatible Brands
LG, select Kenmore, Kenmore Elite
Installation Notes
⚠️ Unplug Washer And Shut Off Water Before Starting — Drain Residual Water First Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Place towels down and have a shallow pan ready, since the pump housing will hold residual water even after a completed cycle — draining this into a pan before disconnecting hoses will save you a mess. On many models, this pump is fully accessible by removing the front lower access panel or kick plate, without needing to tip the washer onto its back — check this first, since it can save significant time and effort compared to some online guides that recommend tipping the unit. Photograph the hose routing and wiring connections before disconnecting anything. Disconnect the two hose clamps connecting the pump to the tub and drain hose, and unplug the electrical connector from the pump motor. Remove the mounting screws or clips securing the pump assembly and lift it free, checking the impeller area for coins, buttons, or debris while it's out — clearing a clog here may have been the actual cause of the original symptom. Install the new AHA72973309 in the same orientation, reconnect both hoses with their clamps, and reconnect the electrical connector fully. Reinstall the front access panel, restore water and power, and run a short cycle to confirm normal draining, recirculation spray, and no leaks around the pump housing. Tools needed: Phillips screwdriver, hose clamp pliers, shallow pan or towels, work gloves.
Frequently Asked Questions
Do I really need to tip the washer over to replace this pump?
Not necessarily — check your model first. While a lot of general online guidance recommends tipping the washer onto its back to access the pump from underneath, many LG and Kenmore Elite front-load models make this pump fully accessible through the front lower access panel or kick plate instead, without any tipping required. It's worth removing that panel first and seeing what you find before committing to the more involved tip-over approach.
Why does this one pump handle both draining and something during the wash cycle?
LG's front-load washers use this same Askoll pump for two different jobs at different points in the cycle: pumping wastewater out during the drain step, and recirculating water from the bottom of the tub back up through the dispenser and spray nozzle during wash and rinse to shower it over the load. That recirculation spray is part of how these washers clean effectively while using less water than an older top-load design. Because one pump does both jobs, a failure can affect draining, wash performance, or both, depending on what's actually gone wrong inside it.
There's water left in the tub after every cycle. Is this definitely the pump?
It's one of the most common causes, but check the easy things first. A clogged drain filter or a kinked drain hose can produce the same "won't drain" symptom and cost nothing to fix. If the filter and hose are clear and water is still standing in the tub, or if the pump hums but doesn't seem to move any water, the pump assembly itself has likely failed.
My washer drains fine but clothes aren't coming out as clean. Could this pump be the cause?
Possibly. Since this same assembly also handles the recirculation spray during wash, a partial failure can leave draining intact while weakening or eliminating that spray function, which reduces how effectively detergent and water reach the load. If drainage is normal but wash performance has noticeably declined, it's worth having this pump checked as one possible cause alongside things like detergent dosing and water hardness.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same Askoll M120-2 dual-function pump design, wiring, and mounting configuration as the drain and circulation pump assembly originally installed in your front-load washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WPW10409079 Washer Genuine OEM Drain Pump
Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079.
Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle. The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.
WH11X39237 Genuine OEM GE Washer Drain Pump
The WH11X39237 is a Genuine OEM GE replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle.
This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The WH11X39237 Genuine OEM GE Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the drum after a cycle
Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes)
Loud humming, grinding, or buzzing noise during the drain cycle
Washer stopping mid-cycle due to a drain fault
Water leaking from around the drain pump area
Drain pump running continuously but water not being expelled
Pump impeller jammed by debris and motor burned out
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790.
WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part.
Compatibility
This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines:
GE front-load washers — GFW510 series
GE front-load washers — GFW550 series
GE front-load washers — GFW650 series
GE front-load washers — GFW655 series
GE front-load washers — GFW850 series
GE Profile front-load washers — PFW870, PFW950, PFW955 series
GE Profile front-load washers — PFQ83 series
GE 2-in-1 Washer/Dryer Combo (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included
Removes water from the drum during drain and spin cycles for proper washer operation
Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs
Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models
WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539
Direct replacement — installs into existing pump housing with no modification required
Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series
DIY-friendly repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
WH11X39237
Supersedes
WH11X29539 (discontinued)
Part Type
Washer Drain Pump and Filter Assembly
Condition
Genuine OEM
Application
GE Front-Load Washers and 2-in-1 Washer/Dryer Combos
Voltage
120V AC
Frequency
60 Hz
Amperage
1.2A
Includes
Pump motor, impeller housing, and integrated filter
Compatible Series
GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83
Compatible Brands
GE, GE Profile
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels.
Frequently Asked Questions
What is the difference between WH11X39237 and WH11X29539?
These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order.
Should I check the pump filter before replacing the drain pump?
Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step.
How do I know if my drain pump has failed?
A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out.
Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models?
Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump and filter assembly installed in compatible GE and GE Profile front-load washers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
W10876600 Washer Genuine OEM Drain Pump – Compatible with Whirlpool, Maytag, Amana, and Crosley Washers
Product Description
Quickly and efficiently remove water from your washer with the W10876600 Washer Genuine OEM Drain Pump. This factory-approved replacement pump removes water from the tub during wash and spin cycles, ensuring smooth performance and proper draining. A faulty drain pump can cause standing water, error codes, or incomplete cycles. Replacing it with this Genuine OEM part restores dependable drainage and long-lasting washer performance.
Replaces Part Numbers
W10876600, 4455877, W10727777, W10876600VP, PD00034529, EAP11738156, AP6004933, PS11738156.
Compatibility
This Genuine OEM drain pump fits select Whirlpool, Maytag, Amana, and Crosley top-load and front-load washers.
Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC465HW0, and Amana NTW4516FW3.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Genuine OEM Replacement – Factory-approved for perfect fit and reliable operation
💧 Efficient Water Removal – Quickly drains water from the washer tub after each cycle
💪 Durable Motor Design – Built to withstand repeated use and heavy loads
🛠️ DIY Installation – Direct-fit replacement installs easily with basic tools
🛡️ Fixes Common Issues – Solves washer not draining, standing water, or “F9E1”/“SD” error codes
📐 Product Specification
Part Number: W10876600
Component Type: Washer Drain Pump Assembly
Material: Heavy-duty plastic pump housing and electric motor
Voltage: 120V AC
Mounting: Direct-fit on washer base with wiring harness connection
Compliance: Genuine OEM certified
🛠️ Installation Notes
Tools Needed: Nut driver, pliers, towel or bucket
⚠️ Safety First: Always unplug the washer and disconnect water supply before performing repairs to prevent electrical shock or leaks.
Steps:
Disconnect power and water hoses.
Tilt the washer back or remove the front access panel.
Unplug the wiring harness and loosen the clamps on the drain hoses.
Remove the old pump and install the new W10876600 pump.
Reconnect hoses and wiring, secure the pump, and restore power.
Run a rinse or drain cycle to verify proper operation.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Genuine OEM Replacement Part
🔄 30-Day Return Policy
Fix washer drainage issues fast — Add to Cart Now for a factory-quality repair that lasts!
W11458345 Genuine OEM Washer Drain Pump - Compatible with Whirlpool, Maytag, Amana
Product Description
Restore your washer’s performance with the W11458345 Genuine OEM Washer Drain Pump. This Whirlpool-manufactured pump is designed as a replacement for select Whirlpool, Maytag, Amana, Inglis, and Kenmore washing machines. It efficiently drains wastewater during wash cycles and includes a large filter that can be cleaned monthly with Washing Machine Cleaner Tablets. This part addresses issues like water not draining, loud buzzing or grinding noises, or failure to enter agitation cycles, often caused by blockages, wear, or pump motor failure.
Note: Includes (1) drain pump assembly. Disconnect power before installation. Verify compatibility with your washer model.
Replaces part numbers: W11458345, W11316609, W10918608, W11319789, PD00062450, EAP16218041, AP6989186, PS16218041.
Compatibility:
Compatible with select washer models, including but not limited to:
Whirlpool: WFW862CHC3, WFW6620HW1, WFW6620HW2, WFW9620HC2, 8TWFW8620HW1
Maytag: MHW5630HW1, MHW5630HW3, 7MWFW5622HW2
Amana: NFW5800HW0
Kenmore: 110.42932200
Inglis: IFW5900HW0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Amana, Inglis, and Kenmore washers.
🔧 Specifications: Genuine OEM Whirlpool drain pump, 120V, stainless steel construction.
💪 Reliable Performance: Efficiently drains wastewater for optimal washer operation.
🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–60 minutes.
🛡️ Effective Fixes: Resolves water not draining, buzzing/grinding noises, or agitation cycle issues.
Product Specification
Part Number: W11458345
Component Type: Washer drain pump assembly
Material: Stainless steel and plastic (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15)
Dimensions: Approximately 9.75" L x 9.5" W x 5.25" H (Based on web:0)
Weight: 3.32 lbs (Based on web:0)
Electrical Specs: 120V, submersible design (Based on web:0, web:2)
Compliance: UL-listed, Prop 65 warning for California (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15)
Installation Notes:
Safety First: Disconnect the washer from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your washer running smoothly today!
Add to cart now for a reliable fix!
