ERP 00759374 Oven Cooling Fan Assembly
Fits Specific Bosch brands include Bosch, Thermador, Gaggenau Oven models
Description: This Fan Blower is a replacement part compatible with specific Bosch oven models. It is responsible for circulating air and dissipating heat inside the oven cavity.
Replaces Part Numbers: 00759374, 00755055, 4163073, AP5950846, PS10058376.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
W11623080 Oven Genuine OEM Door Gasket
Replaces Part Numbers: W11623080, WPW10282960, W10282960, W10739089, AP7194861, PS16745120.
Description: This Oven Door Seal is a Genuine OEM part specifically designed for specific Whirlpool wall oven models. It provides an airtight barrier between the door and oven interior during cooking and baking. Made of heat-resistant materials, the door seal withstands high oven temperatures. Common causes of a bad door seal can include normal wear and tear from repeated use over many years of cooking. Exposure to extremely high heat cycles may also degrade the seal prematurely.
XPARTCO H150 Furnace Silicon Nitride Rod Ignitor
The H150 universal gas furnace igniter come with a 1.95-inch ceramic nitride heating element, a 1.25-inch ceramic insulator, a 304 stainless steel bracket, and a 15.5-inch high temperature resistant wire(20 AWG). Voltage: 120V±10%-15%, 50/60HZ. Power Rating: 150W. Cold resistance: 9-17Ω. At 120V furnace igniter H150 can reach 1200 degrees in a short time
The H150 universal furnace igniter replacement can be used in a wide range of machines and is the perfect replacement for silicon carbide ignitors in water heater boilers and gas forced-air furnaces, replacing more than 180 types of ignitors and covering nearly 90% of all applications. Such as stoves, furnace, warm air motion, gas ignition, hot surface igniter, infrared light source, pool heater, boiler, etc
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WB44T10055 Oven Genuine GE OEM Bake Element
Oven Bake Element
Description: This Oven Bake Element is an OEM part for specific GE oven models, designed to provide the heat necessary for baking. This element is located at the bottom of the oven cavity and turns red hot when electricity flows through it, thereby heating the oven to the desired temperature. It's a crucial component for ensuring your oven can reach and maintain the set baking temperatures, playing a key role in the cooking process by providing consistent, even heat. The most common cause of bake element failure is normal wear and tear over time. Frequent use can lead to the element burning out, which prevents it from heating. Additionally, physical damage during cleaning or cooking can also cause the element to fail prematurely.
Replaces Part Numbers:WB44T10055, 1087447, WB44T10021, AH956152, EA956152, AP3793599, PS956152.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 22003483 Washer Drive Belt
The XPARTCO 22003483 is an aftermarket replacement drive belt for Whirlpool-built Maytag Atlantis top-load washers. This belt is the mechanical link between the drive motor and the washer's drive system — it's what actually transmits the motor's rotation to spin the drum, so both agitation and spin depend entirely on this belt gripping its pulleys correctly and staying properly tensioned.
Made of black rubber, this belt measures 52 inches long. Over years of use, the belt material gradually hardens and glazes over, becoming smooth and "slick" rather than gripping the pulleys firmly — this degradation can cause the belt to slip under load even before it shows any visible cracking or damage. A worn belt produces a range of symptoms depending on how far the wear has progressed: the washer may pump water but fail to spin, fail to agitate at all, spin noticeably slower than normal, or produce a chirping or slipping noise, especially as the motor shifts between wash and spin modes. It directly replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667.
Quick Answer
The XPARTCO 22003483 Washer Drive Belt fixes Maytag (Whirlpool-built) top-load washers that pump but won't spin, won't agitate, spin slowly, or make a chirping/slipping noise as the motor shifts modes. 52 inches long, black rubber. Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, 824667. A belt can slip and cause symptoms well before it looks visibly worn — years of use leave the rubber "slick" and unable to grip the pulleys properly, even without visible cracking.
Common Problems This Part Fixes
Washer pumps water but won't spin
Washer won't agitate
Washer spins noticeably slower than it used to
Chirping or slipping noise, especially as the motor shifts between wash and spin modes
Belt that has become glazed, hardened, or "slick" from years of use
Visible cracking, fraying, or glazing on the belt surface
General noise or vibration during the wash or spin cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drive belt directly replaces the following OEM and cross-reference part numbers:
WP22003483 22003483, 22002709, 62618130, 824667, AP6006365, EAP11739438, WP22003483VP, AWP47150, PD00002551, PS11739438
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drive belt is compatible with select Maytag Atlantis top-load washers built on the Whirlpool platform, including model numbers such as:
MAV4057AWQ, MAV4057AWW, MAV4500AWW
MAV5000AWQ, MAV5000AWW, MAV5057AWQ, MAV5057AWW, MAV5960AWW
MAV6000AWQ, MAV6000AWW, MAV6057AWQ, MAV6057AWW
MAV6200AWQ, MAV6200AWW, MAV6250AWQ, MAV6250AWW, MAV6257AWQ, MAV6257AWW
MAV6548AWQ, MAV6548AWW, MAV6601AWQ, MAV6601AWW, MAV6650AWW, MAV7000AWQ
Note: Always verify your full model number before ordering, since Whirlpool and Maytag use different belt lengths and profiles across their washer lineup. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drive belt — transmits motor power to spin the washer drum
Resolves "pumps but won't spin," "won't agitate," "spins slowly," and "chirping/slipping noise" symptoms caused by belt wear
52 inches long, black rubber construction
Rides on three pulleys to transfer motor rotation to the drive system
Direct drop-in replacement matching the original length and profile
Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667
Compatible with Maytag Atlantis top-load washers built on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
22003483
OEM Part Number
WP22003483
Part Type
Washer Drive Belt
Condition
Aftermarket Replacement
Application
Maytag Atlantis Top-Load Washers (Whirlpool-Built)
Length
52 inches
Material
Rubber
Color
Black
Function
Transmits motor rotation to the drive system to spin the drum
Quantity
1 drive belt
Compatible Brand
Maytag (Whirlpool-built)
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the motor and belt area. Loosen the motor's mounting screws so the motor can be pushed toward the drum, releasing tension on the old belt. Slide the old belt off its three pulleys and remove it. Route the new 22003483 belt over the same three pulleys, matching the original path. With the belt in place, gently push the motor away from the drum by hand to apply tension, then tighten the motor's mounting screws while continuing to check belt tightness — the belt should have firm, even tension across all three pulleys with no excess slack. Reinstall the rear panel, restore power, and run a full test cycle through both agitate and spin to confirm smooth, quiet operation with no chirping or slipping. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
My washer makes a chirping noise when it shifts from agitate to spin. Is that the belt?
Yes, this is a documented symptom of a worn belt. One long-term owner traced this exact chirp to a 10-year-old belt that had become "slick" from age — smooth and hardened enough that it briefly slipped on the pulleys as the motor shifted between modes, rather than moving cleanly into position. Replacing the belt resolved the noise completely.
My belt doesn't look cracked or damaged. Could it still be the problem?
Yes. A belt can degrade in ways that aren't obvious at a glance — the rubber can harden and glaze over time, becoming slick and losing its grip on the pulleys even without visible cracking or fraying. If your washer is slipping, chirping, or spinning weakly and the belt has been in service for many years, age-related slickness is a reasonable explanation even if the belt still looks intact.
How do I know if I have the right belt length for my washer?
This belt is 52 inches long and specific to the Maytag Atlantis top-load platform. Whirlpool and Maytag use different belt lengths across other washer models, so always confirm your model number matches the compatibility list, or measure your old belt for comparison, before ordering.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, profile, and material of the original WP22003483 drive belt used in compatible Maytag Atlantis top-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
9759242 Oven Thermal Fuse
This non resettable oven thermal cut out fuse acts as a safety cutting power to the oven if it becomes over heated.
Replaces Part Numbers: WP9759242, 9759242, 4452223, OEM18042050, AP6014015, PS11747248, WP9759242VP
Description: This Thermal Fuse is a Genuine part for specific KitchenAid, Kenmore, Whirlpool oven models. It acts as a safety device that cuts off power to the oven if it overheats, preventing potential damage or fire hazards. Common causes of a bad thermal fuse can include prolonged exposure to high temperatures, electrical surges, or faulty oven components that cause overheating. When the fuse blows, it disrupts the electrical circuit, rendering the oven inoperative until the fuse is replaced.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
318254916 Oven Genuine OEM Bake Element
Description: This oven bake element is a Genuine part responsible for generating the heat necessary for baking and roasting in a oven. This part is located at the bottom of the oven's interior cavity or beneath the oven floor or base. When the oven is in use and the bake function is selected, electric current flows through the bake element, causing it to heat up. This heat rises and circulates within the oven, providing the consistent and even temperature required for cooking.
Replaces Part Numbers: 318254916, 318254915, 1940637, 318254903, 318254911, 7318254903, 7318254911, AH3497886, EA3497886, AP5270425, PS3497886.
California Residents only:
WARNING: California’s Proposition 65
WG24 Microwave Universal Mica Sheet, Waveguide Cover (2.5" × 4.2") – Fits Most Microwave Ovens
Product Description
Restore safe and efficient microwave operation with the WG24 Microwave Universal Mica Sheet / Waveguide Cover. This heat-resistant mica sheet protects the waveguide opening from grease, moisture, and food splatter while allowing microwaves to pass through efficiently. A damaged or burned waveguide cover can cause sparking, arcing, or uneven heating. Replacing it with this durable WG24 mica sheet helps prevent damage to the magnetron and ensures consistent microwave performance.
Replaces Part Numbers
WG47, Microwave Mica Sheet, Universal Waveguide Cover, Microwave Waveguide Plate
Compatibility
This universal microwave mica sheet is compatible with most countertop, over-the-range, and built-in microwave ovens from major brands including GE, Whirlpool, Samsung, LG, Panasonic, Kenmore, Frigidaire, and more.
⚠️ Universal fit — may be trimmed to size if required.
Always verify dimensions before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Universal Replacement – Fits most microwave waveguide openings
🔥 Heat-Resistant Mica Material – Withstands high temperatures without burning
⚡ Prevents Sparking & Arcing – Protects waveguide and magnetron
✂️ Customizable Fit – Can be trimmed for exact size
💰 Cost-Effective Repair – Extends microwave life at minimal cost
📐 Product Specification
Part Number: WG24
Component Type: Microwave Waveguide Cover / Mica Sheet
Material: Natural mica
Dimensions: 2.5 inches × 4.2 inches
Thickness: OEM-equivalent
Color: Light brown
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Scissors (if trimming required), Phillips screwdriver
⚠️ Safety First: Unplug the microwave before servicing.
Steps:
Disconnect microwave from power.
Remove the old or damaged waveguide cover.
Clean the waveguide opening area.
Trim the WG24 mica sheet if necessary.
Install the new mica sheet using the original mounting method.
Restore power and test microwave operation.
⏱️ Time Required: 5–10 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Eliminate sparking and protect your microwave — Add to Cart Now for a simple, effective repair!
XPDE60-20066A Microwave Mounting Flat Bolt
Fits Specific Samsung, GE, Whirlpool Over The Range Microwave models.
Replaces Part Numbers:DE60-20066A, AP4219712, OEM12659141, PS4226718, WB01X10180, OEM9617897, AP3205964, 942461, AH651196, EA651196, PS651196, WB1X10180.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
W10201551 Oven Genuine OEM Broil Element
Description: This Oven Broil Element is an OEM part for specific Whirlpool oven models. It is responsible for providing the necessary heat for broiling, ensuring that food is cooked evenly from above. Causes of a bad broil element can include electrical malfunctions, wear and tear from regular use, or damage from high temperatures and thermal cycling over time. These issues can impair the element's ability to heat properly.
Replaces Part Numbers: W10201551, 1471986, 74004106, 7406P237-60, 7406P474-60, AH2342087, EA2342087, AP4365339, PS2342087, W10201551VP.
California Residents only:
WARNING: California’s Proposition 65
