Search results for "Dryer Switch"

XPARTCO 3406107 Dryer Door Switch – Replaces WP3406107 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers Product Description Ensure your dryer starts safely and operates correctly with the XPARTCO 3406107 Dryer Door Switch. This high-quality aftermarket replacement detects when the dryer door is closed, enabling the motor to run and heat to activate. A defective switch can prevent your dryer from starting or cause it to stop mid-cycle. Replacing it with this reliable XPARTCO switch restores normal operation and dependable performance. Replaces Part Numbers WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, PS11741701. Compatibility This replacement door switch fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Estate dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.60902990, and Maytag MEDC200XW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Engineered to match OEM safety and electrical performance 🚪 Restores Start Function – Ensures dryer runs only when the door is fully closed 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ Quick Installation – Simple plug-in wiring and snap-in mounting 🛡️ Fixes Common Issues – Solves dryer not starting, shutting off mid-cycle, or running with door open 📐 Product Specification Part Number: 3406107 Component Type: Dryer Door Switch Assembly Material: Plastic body with metal actuator lever and 3-pin terminal Mounting: Snap-in installation behind front panel Electrical Rating: 15A / 125-250V AC Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect power and open the dryer door. Remove the top or front panel (depending on model). Unplug the old switch’s wire connectors. Press the locking tabs and remove the old switch. Install the new XPARTCO 3406107 switch, reconnect wires, and secure panels. Restore power and test dryer start function. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s start function — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO DC64-00828B Dryer Door Switch The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open. This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers. Common Problems This Part Fixes Dryer not starting even though the door is closed Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently Error codes dC, dF, dE, or d0 displayed on models with digital displays Dryer continuing to run with the door open (unsafe failure mode — replace immediately) Interior dryer light not turning on when the door is opened Door switch button visibly broken, stuck, or not making the expected click when pressed Multimeter test shows the switch fails to change state when actuated Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including: Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related) Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related) Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related) Samsung dryers — DV5 series (DV50K7500EW and related) Samsung dryers — DVE series (DVE60M9900W and related electric models) Samsung dryers — DVG series (DVG45N5300V and related gas models) Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch that detects whether the dryer door is closed — required for the dryer to start and run Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing Durable plastic housing with metal contacts — withstands frequent door open/close cycles Resolves Samsung door-related error codes including dC, dF, dE, and d0 Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436 Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC64-00828B Also Replaces DC64-00828A (prior version) Part Type Dryer Door Switch (Door Jamb Switch) Condition Aftermarket Replacement Application Electric and Gas Dryers (Samsung platform) Dimensions Approximately 1.73"L x 1.73"W x 0.47"H Color White Material Plastic / Metal Error Codes Resolved dC, dF, dE, d0 (door-related) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What do error codes dC, dF, dE, and d0 mean on Samsung dryers? These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage. My dryer is running with the door open — what should I do? A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer. What is the difference between DC64-00828B and DC64-00828A? These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing. My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch? Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10820036 Washer / Dryer Door Switch The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running. Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed. Quick Answer The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing. Common Problems This Part Fixes Washer/dryer combo won't start even though the door is fully closed Cycle stops partway through, as if the door had been opened Door doesn't feel like it's "clicking" or latching the way it used to Console shows a door-related error or won't advance past the door-closed step Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed Visibly cracked, loose, or broken switch housing or lever Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following OEM part number: W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153. No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions. Model list not yet confirmed: A specific compatible model list for W10820036 was not available at the time this page was built. Please verify your exact model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase. Key Features Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units Detects whether the door is closed and latched before allowing the wash or dry cycle to run Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms Direct drop-in replacement for the original W10820036 switch — no modification required Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10820036 OEM Part Number W10820036 Part Type Washer/Dryer Combo Door Safety Switch Condition Aftermarket Replacement Application Whirlpool-Built Washer/Dryer Combination Units Function Door-closed safety interlock for wash and dry cycles Quantity 1 switch Compatible Brand Whirlpool (combo platform) Installation Notes ⚠️ Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the door switch on combo units is typically through the front or top control panel — photograph the wiring harness before disconnecting it so you can match it exactly on reassembly. Confirm the new switch's lever aligns with the door strike before securing the mounting screws, and test for a firm, positive click when the door closes before restoring power and running a cycle. If your unit's service manual is available, follow its specific access and mounting steps rather than relying solely on general guidance. Frequently Asked Questions My combo unit won't start. Is this definitely the door switch? It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit. Does this switch control both the washer and dryer functions? On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10420741 Genuine OEM Dryer Push To Start Switch - Compatible with Whirlpool, Kenmore, Maytag Product Description Restore your dryer’s functionality with the WPW10420741 Genuine OEM Dryer Push To Start Switch. This Whirlpool-manufactured switch, featuring screw terminals, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It initiates the drying cycle with a simple button press, addressing issues like the dryer not starting or starting inconsistently. Built for durability, it ensures reliable performance under frequent use. Note: Includes (1) push to start switch. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WPW10420741, W10420741, PD00008413, EAP3632880, AP6021228, PS11754549. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WET4027HW0, WET4027HW1, WET4027HW2, YWET4027HW0, 7MWGT4027HW0 Kenmore: 110.97591420, 110.97591220, 110.97592420 Maytag: YNED4655EW, YIED4671EW Roper: RED4516FW0, RED4640YQ0, RED4640YQ1, RED4645EW0 Crosley: VDEW6511RW0, VED6505GW0 Amana: NED4655EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana, and other dryers. 🔧 Specifications: Genuine OEM Whirlpool push to start switch with screw terminals, 120V, 2-terminal configuration. 💪 Reliable Performance: Initiates drying cycle with a button press, ensuring consistent operation. 🛠️ Easy Installation: Requires a screwdriver; typically installed in 10–20 minutes. 🛡️ Effective Fixes: Resolves dryer not starting or inconsistent starting issues. Product Specification Part Number: WPW10420741 Component Type: Dryer push to start switch Material: Plastic and brass/stainless steel Electrical Specs: 120V, 2-terminal, normally open, single-pole single-throw (SPST) Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

XPARTCO 3406105 Dryer Door Switch Replaces WP3406105 The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open. This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560. Common Problems This Part Fixes Dryer will not start at all — door switch not completing the circuit when door is closed Dryer starts only when the door is slammed or held firmly closed Dryer continues to run after the door is opened — switch not opening the circuit Drum light not turning on when the door is opened (on models with drum light) Dryer starts intermittently — door switch contact worn and making unreliable contact Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear Door switch visibly cracked, broken, or the actuator button no longer springs back Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Roper dryers Estate dryers Crosley dryers Inglis dryers Admiral dryers Jenn-Air dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L Stainless steel terminals and heat-resistant housing Kit includes switch and 3-wire harness assembly — complete plug-in replacement Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560 Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3406105 OEM Part Number WP3406105 Part Type Dryer Door Switch Assembly (SPDT 3-Wire) Condition Aftermarket Replacement Application Gas and Electric Dryers Switch Type Single Pole, Double Throw (SPDT) Wires 3-wire Voltage 120-240V Frequency 50-60Hz Amperage 11A Horsepower 1/3 HP Switch Body Dimensions 1-3/4" L x 1-5/8" W x 1-1/4" H Harness Length 7-3/4 inches Color Off-White / Black / Gray Material Plastic / Metal (stainless steel terminals) Includes Switch and 3-wire harness assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife. Frequently Asked Questions What does the dryer door switch do? The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit. How do I test the door switch with a multimeter? Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed. What is the difference between 3406105 and 3406104? The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement. Why does this switch have 3 wires when my old switch only had 2? The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406108 Dryer Door Switch - Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO 3406108 Dryer Door Switch. This door switch is designed for select Whirlpool, Kenmore, Maytag, and other dryer models, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch with 2 wire leads and a two-prong plug. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP3406108, 3406108, PD00029356, EAP11741702, PS11741702, AP6008562.  Compatibility: Compatible with models including but not limited to: Whirlpool: LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. Kenmore: 11060012000, 11060022010, 11060232000 Maytag: MEDC400VW0, AED4475TQ1 Other brands: Select models requiring 3406108 (e.g., Amana, Crosley, Roper) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Roper dryers requiring 3406108. 🔥 Specifications: Replacement dryer door switch, 2 wire leads, two-prong plug, 120-240V, 50-60Hz, 11A, 1/3HP. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop when door is opened. Product Specification Part Number: XP3406108 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: Two-prong plug with 2 wire leads Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

17438000001584 Genuine OEM Midea Dryer Belt Safety Switch The 17438000001584 is a Genuine OEM Midea replacement belt safety switch compatible with select Midea, Criterion, and Insignia electric and gas dryers. This safety switch is positioned near the drive belt and tensioner pulley assembly, where it monitors belt-related conditions and interrupts electrical flow to the motor or heating circuit if a fault or unsafe condition is detected — such as a broken or severely slipped drive belt. This is a key safety mechanism: if the belt fails and the drum can no longer be safely driven, this switch helps prevent the motor from continuing to run unsafely or the heater from continuing to operate without normal airflow from drum rotation. When this switch fails, the dryer may not start, may shut off unexpectedly during operation, or may fail to heat even though other components test correctly. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438000001584 measures 2"L x 2"W x 3"H and weighs approximately 1 oz. It is found on the same parts diagram as the drive belt, tensioner pulley assembly, and drum support components on compatible models. Installs in 30–45 minutes with basic hand tools. Quick Answer The 17438000001584 Genuine OEM Midea Dryer Belt Safety Switch fixes Midea, Criterion, and Insignia dryers that won't start, shut off unexpectedly during operation, or fail to heat despite other components testing normally. Mounted near the drive belt and tensioner pulley assembly — interrupts power if a fault or unsafe belt condition is detected. Dimensions: 2"L x 2"W x 3"H, approx. 1 oz. Genuine OEM. Compatible with Midea MLG45N3BMG, Criterion CDG41N1AW, CDG45N1AW, and related Midea-platform dryer models. Common Problems This Part Fixes Dryer not starting — safety switch not signaling normal belt/drive conditions Dryer shutting off unexpectedly partway through a cycle Dryer not heating despite the heating element, thermostat, and other components testing normal Dryer behaving erratically after a drive belt failure or replacement Intermittent power interruption during operation traced to this switch area Switch contacts failing continuity test with a multimeter Replaces Part Numbers This belt safety switch directly replaces the following part number: 17438000001584, AP7157511, PS18188483 This is the Midea manufacturer part number used across multiple Midea, Criterion, and Insignia dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This belt safety switch is compatible with select Midea, Criterion, and Insignia dryers, including: Midea MLG45N3BMG gas dryer Midea MLG45N1BWW, MLG45N3BWW, and related MLG gas dryer series Midea MLE series electric dryers (select models) Criterion CDG41N1AW, CDG45N1AW gas dryers (air vent series) Insignia electric and gas dryers built on the Midea platform (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Safety switch mounted near the drive belt and tensioner pulley assembly Interrupts electrical flow to the motor or heating circuit if a fault or unsafe belt-related condition is detected Compact design: 2"L x 2"W x 3"H, approximately 1 oz Compatible with Midea MLG/MLE series, Criterion CDG series, and Insignia Midea-built dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number 17438000001584 Part Type Dryer Belt Safety Switch Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Dimensions 2"L x 2"W x 3"H Weight Approximately 1 oz Location Near drive belt and tensioner pulley assembly Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum, drive belt, and tensioner pulley assembly. Locate the belt safety switch in this area — refer to your model's parts diagram to confirm its exact mounting position, as it is positioned near the belt and tensioner pulley support. Photograph the wire connections before disconnecting. Disconnect the wires from the old switch, remove the mounting screw or clip, and pull the switch free. Install the new 17438000001584 switch in the same position, secure the mounting hardware, and reconnect the wires. While this area is open, it's a good time to inspect the drive belt and tensioner pulley for wear, since this switch is related to belt operation. Reassemble the front panel and top panel in reverse order. Restore gas and power, and run a test cycle to confirm the dryer starts and runs normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the belt safety switch do? The belt safety switch monitors belt-related conditions near the drive belt and tensioner pulley assembly and interrupts electrical flow to the motor or heating circuit if it detects a fault or unsafe condition — such as a broken or badly slipped drive belt. This is a protective measure: if the belt has failed and the drum can no longer be driven normally, the switch helps prevent continued unsafe operation of the motor or heater. It works alongside other safety components in the dryer (like the door/cover switch and thermal limiters) as part of an overall safety system. My dryer just had a belt replacement and now isn't working right — could this switch be involved? It's possible. Since this switch is positioned near the belt and tensioner pulley assembly, it can be disturbed, dislodged, or its connector improperly reseated during a belt replacement. If your dryer is behaving erratically after a recent belt repair — failing to start, shutting off, or not heating — check that this switch's connector is fully seated and that the switch itself wasn't damaged during the repair. If the connector is good and the switch tests as an open circuit with a multimeter, it has failed and needs replacement. How do I test if this safety switch has failed? Unplug the dryer, disconnect the switch's wire connector, and set your multimeter to continuity mode. With the belt and tensioner mechanism in their normal operating position, the switch should show closed continuity (allowing current to flow). If the switch shows an open circuit when it should be closed, it has failed and needs replacement. Always refer to your specific model's wiring diagram to confirm the expected switch state, since exact behavior can vary by dryer model. Does this switch fit Insignia and Criterion dryers as well as Midea? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in certain configurations are manufactured by Midea and use the same internal components, including this belt safety switch. Confirmed Criterion models include the CDG41N1AW and CDG45N1AW gas dryers. Always verify your specific model number before ordering to confirm compatibility. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same belt safety switch installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE04X24719 Dryer Start Button – Compatible with GE Dryers Product Description Restore dependable operation with the WE04X24719 Dryer Start Button. This replacement button allows you to start and control drying cycles. A worn, cracked, or unresponsive button can prevent the dryer from starting or make operation difficult. Replacing it with this replacement button ensures smooth function and reliable performance. Replaces Part Numbers WE04X24719, PD00046802, AP6034220, 4587500, PS11766637. Compatibility This start button is compatible with select GE dryers. Example compatible models include (but are not limited to): GE GTD42EASJ2WW, GE GTD65EBSJ3WS, and GE GTD45EASJ2WS. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Reliable Replacement – Reliable aftermarket replacement for GE dryer start button 🔘 Reliable Operation – Restores start functionality for dryer cycles 💰 Cost-Effective Fix – Affordable way to replace a worn or broken button 🛠️ Quick Installation – Installs in minutes with basic tools 🛡️ Fixes Common Issues – Resolves unresponsive, cracked, or missing start button problems 📐 Product Specification Part Number: XPWE04X24719 Component Type: Dryer Start Button Material: Durable plastic construction Mounting: Snap-in design, direct replacement Operating Conditions: Residential dryer use 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver (if needed) ⚠️ Safety First: Always unplug dryer before starting repairs to avoid electrical shock. Steps: Unplug dryer and locate control panel. Remove panel screws to access start button assembly. Release old button from mounting clips. Insert new WE04X24719 button into slot until it clicks securely. Reassemble control panel and restore power. Test dryer to ensure button works correctly. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix your dryer start function today — Add to Cart Now for a genuine, factory-approved repair!

Read more less

XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor Replaces WP8557403 The XPARTCO 8557403 is an aftermarket replacement dryer high-limit thermostat and thermistor sensor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers — including the Whirlpool Duet and Maytag MED series. This single component combines two functions: the high-limit thermostat (rated L146-44C, opens at 295°F) acts as a resettable safety switch that cuts power to the heating element if the dryer air temperature exceeds safe limits, and the integrated 50-ohm thermistor continuously monitors air temperature and sends resistance-based readings to the control board to regulate the drying cycle. When this part fails — whether the thermostat opens permanently or the thermistor provides incorrect temperature data — the dryer may produce no heat, run too hot, take too long to dry, overheat, or display temperature-related error codes. It measures 1-5/8"L x 1-5/8"W x 2"H with approximately 1-5/8" between mounting holes and is constructed from black/gray plastic and metal. It directly replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386. Note: the exhaust duct thermostat and thermal fuse are separate parts — if those have also failed, they must be ordered separately. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor fixes Whirlpool Duet, Maytag MED, and related dryers with no heat, overheating, or erratic temperature. Combined part: L146-44C high-limit thermostat (opens at 295°F, auto-resets) + 50-ohm NTC thermistor. 1-5/8"L x 1-5/8"W x 2"H, ~1-5/8" between mounting holes. Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, PS11746386. For Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, and Admiral electric dryers. Common Problems This Part Fixes Dryer produces no heat — high-limit thermostat has failed open Dryer overheating — thermostat not opening at the correct temperature Dryer takes too long to dry — thermistor providing incorrect temperature readings to the control board Dryer cycling on and off erratically — thermistor fault causing incorrect cycle control Temperature-related error codes on models with digital displays Multimeter test shows open circuit on the thermostat at room temperature Multimeter test shows open or shorted thermistor (not ~50 ohms at room temperature) Replaces Part Numbers This thermostat/thermistor assembly directly replaces the following OEM and cross-reference part numbers: WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat and thermistor is compatible with select electric dryers only from the following brands: Whirlpool electric dryers — Duet, WED5000, WED5500, WED5600, WED5620, WED8000, WED8200, WED8500, WED9200, WED92HEF, WED7000 series and related models Maytag electric dryers — MED3500, MED5630, MED6630, MED7230, MEDB835 series and related models Kenmore / Sears electric dryers — 110-series (Whirlpool-built models) Amana electric dryers (select models) KitchenAid electric dryers (select models) Jenn-Air electric dryers (select models) Roper electric dryers Admiral electric dryers Norge electric dryers Magic Chef electric dryers Note: This part is for electric dryers only. The exhaust duct thermal fuse and cycling thermostat are separate parts — if those have also failed, they must be ordered separately. Always verify your model number before ordering. Key Features Combined high-limit thermostat and thermistor in a single assembly — replaces both functions in one part High-limit thermostat rated L146-44C — opens at 295°F (146°C), resets automatically when cooled Integrated 50-ohm NTC thermistor — continuously monitors dryer air temperature and sends readings to the control board for cycle regulation Dimensions: 1-5/8"L x 1-5/8"W x 2"H; approx. 1-5/8" between mounting holes Black/gray plastic and metal construction Electric dryers only — not for gas dryer models Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386 Compatible with Whirlpool Duet, Maytag MED, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8557403 OEM Part Number WP8557403 Part Type Dryer High-Limit Thermostat with Integrated Thermistor Sensor Condition Aftermarket Replacement Application Electric Dryers Only Thermostat Rating L146-44C — opens at 295°F (146°C), auto-resets Thermistor 50-ohm NTC (at room temperature ~25°C) Dimensions 1-5/8"L x 1-5/8"W x 2"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Black / Gray Material Plastic / Metal Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. The 8557403 thermostat/thermistor assembly is typically located on the heating element housing or duct inside the dryer — access it by removing the back panel. On Whirlpool Duet and Maytag front-load-style dryers, the component may be accessible by removing the lower front panel. Photograph all wire connections before disconnecting — the thermistor wires and thermostat wires must be reconnected to the correct terminals. Remove the two mounting screws and pull the old assembly off. Note the position and orientation before removing. Install the new 8557403 assembly in the same position and orientation, reconnect all wires, and reinstall the mounting screws and panel. Restore power and run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions What makes this part unusual — why does it combine a thermostat and a thermistor? The WP8557403 is a combined assembly used on newer Whirlpool Duet and Maytag MED series dryers that use electronic temperature control rather than purely mechanical thermostats. The high-limit thermostat (L146-44C) provides the traditional safety function — it opens the circuit if dryer temperature exceeds 295°F. The integrated NTC thermistor continuously reports resistance-based temperature data to the electronic control board, which uses the data to regulate the heating element and control cycle timing. Both functions are built into a single compact housing, making this a unique part that replaces what older dryers used to handle with separate components. How do I test the thermostat and thermistor? Set your multimeter to continuity or resistance mode. For the thermostat portion: probe the thermostat terminals — at room temperature, a working thermostat shows closed continuity (near-zero resistance). An open circuit at room temperature confirms the thermostat has failed. For the thermistor portion: probe the thermistor terminals — at room temperature (approximately 25°C/77°F), a working 50-ohm NTC thermistor should read approximately 50 ohms. A reading of zero ohms (shorted) or open circuit (no continuity) confirms the thermistor has failed. Either failure mode warrants replacing the complete 8557403 assembly. What is the difference between 8557403 and WP8557403? These are the same part. WP8557403 is the updated Whirlpool OEM part number that superseded the original 8557403. The 1180102 is also a cross-reference for this same assembly. This aftermarket replacement is compatible with all of these numbers. Do I also need to replace the thermal fuse or cycling thermostat? The 8557403 replaces the high-limit thermostat and thermistor mounted on the heating element housing area. The exhaust duct thermal fuse (WP3392519 on most Whirlpool-family dryers) and cycling thermostat (WP3387134) are separate components located on the exhaust duct and are not included in or replaced by the 8557403. If your dryer has no heat, test all thermal components before ordering — check the 8557403 assembly, the thermal fuse, and the cycling thermostat, then order only what has failed. If an overheating event caused the high-limit to fail, the other thermal components may be stressed as well. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal with an L146-44C thermostat and 50-ohm NTC thermistor to match the specifications and performance of the original WP8557403 assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less